Using Costs and Health Benefits to Estimate the Priority of Air Pollution Control Action Plan: A Case Study in Taiwan

A comparative analysis was conducted between the costs and health benefits of the Air Pollution Control Action Plan (APCAP), which can be implemented in any country to improve air quality and human health. In this study, air quality modeling was used to simulate several scenarios and implement the Kriging method to describe the PM2.5 reduction concentration instantly. Then, health benefits were estimated using the environmental benefit mapping and analysis program (BenMAP) with results from the air quality modeling and Kriging method. To estimate the priority of APCAP, 14 pollution control measures that cover point, mobile, and area sources of air pollution in Taiwan were analyzed. The results indicate that the health benefits of the Taiwan APCAP (TAPCAP) are generally greater than the technical costs. Thus, the implementation of this strategy may result in net benefits. In addition, the benefit-to-control cost ratio for health for the 14 pollution control measures was calculated. The results provide evidence to prioritize the implementation of air quality policies with a higher benefit-cost ratio.


Introduction
Air pollution is internationally recognized as a major threat to human health, as continued human exposure to air pollution exacerbates mortality risks and increases medical costs for treating air pollution-related illnesses [1][2][3][4][5][6][7]. According to a 2015 study conducted by the World Health Organization (WHO), early deaths owing to air pollution cost the European Union 1.43 trillion USD in 2010. Moreover, if associated medical costs are considered, this value increases to 1.58 trillion USD. The Organization for Economic Co-operation and Development (OECD) conducted an empirical study on 41 countries in 2017, which demonstrated that 3.2 million people died in 2015 due to air pollution [8]. The corresponding economic losses were estimated at 5.1 trillion USD. Due to the health and economic impacts of air pollution, the control and prevention of air pollution are now among the most important environmental management issues for many countries.
assessments. The three stages conducted when using the IPA framework to perform a monetized assessment of the effects of air pollutant emissions on human health are: (1) simulating the effects of air pollutant emissions on air pollution concentrations, (2) estimating the health impacts caused by changes in pollution concentration, and (3) monetizing these health impacts. One of the strengths of the IPA framework is its ability to clearly describe impact pathways through which air pollutants are emitted and eventually transferred to affected subjects. In addition, it enables quantitative modeling of the effects of pollutants at each key stage of an impact pathway. The IPA framework is, at present, the most commonly used assessment framework for the analysis of air quality policies. The ABaCAS-Taiwan was jointly developed by the Taiwan EPA, U.S. EPA, and the University of Tennessee. In addition to the intrinsic strengths of the ABaCAS system, the ABaCAS-Taiwan system also includes several technical parameters that have been adapted for local application in Taiwan. Therefore, this system is well-suited for air quality analyses in the Taiwanese context, but can also be adapted for use in other countries.
For example, Wang et al. [3] used Software for Model Attainment Test-Community Edition (SMAT-CE) to identify the pollutant concentrations that must be reduced to achieve the 2020 O 3 and PM 2.5 targets (75 ppb and 12 µg/m 3 , respectively) of the U.S. They revealed that anthropogenic NO x , anthropogenic SO x emissions, residential wood combustion PM 2.5 , and direct PM 2.5 emissions from non-electric generating units must be reduced by 25%, 25%, 100%, and 50% over their corresponding 2007 levels, respectively, to meet the 2020 PM 2.5 target. Zhu et al. [4] combined the response surface model (RSM)-linear coupled fitting with SMAT-CE to reduce the dimensions required to establish air quality modeling, and used this approach to investigate the contributions of primary emissions to ambient PM 2.5 levels in the Yangtze River Delta in January and August 2010. In a study on power plants in the Yangtze River Delta, Sun et al. [5] used a multi-pollutant control cost model to identify viable pollution control measures to achieve China's air quality targets, as well as their corresponding emission control costs.
The ABaCAS-Taiwan assessment system is based on the standard ABaCAS framework, and it was created by incorporating Taiwanese data to localize the system. The database includes air quality monitoring data, Taiwan emission data, population, inflation data, incidence rates, prevalence rates, and mortality rates. ABaCAS-Taiwan consists of four modules: Taiwan emission control analysis system (TECAS), advance response surface model (RSM), software for model attainment test (SMAT), and environmental benefits mapping and analysis program-community edition (BenMAP-CE). The TECAS module can be used to estimate the technical cost of a pollution control strategy, while RSM can be used to quickly estimate both O 3 and PM 2.5 levels. Furthermore, RSM can be employed for the rapid calculation of precursor emissions with a minimum number of simulations [6,7,21]. SMAT is used to correct for errors between observed and simulated values, to ensure that the simulated values can be a better fit for the observed values. BenMAP-CE is applied to estimate the health benefits that result from reductions in air pollution, based on the results of the aforementioned simulations [22][23][24][25][26]. As this study required the use of the RSM, SMAT, and BenMAP-CE modules, we have provided a brief description of their technical details in the following subsections.

RSM
The main purpose of the RSM module is to obtain the maximum number of control scenario assessments from the minimum number of scenario simulations [27], thus allowing policymakers to rapidly obtain accurate simulations. To construct an RSM, the first step is to perform weather simulations using the weather research and forecasting model (WRF) and to validate the simulations using meteorological observatory data. We used the same meteorological conditions for the multiple scenarios and only the emissions were altered in different scenarios. The control variables and control matrix needed for the second step were obtained from the Taiwan Emission Data System, with 2013 as the baseline year. There are many factors in the control matrix, including point, line, and area sources in counties in Taiwan. Community Multi-scale Air Quality model (CMAQ) is a model which could simulate by integrating various pollution issues, including ozone, particulate matter (PM), acid deposition and toxic substances, to create the effect of interaction of simulation among different subjects and allow model stimulation to be in line with atmospheric chemistry phenomena [26]. If there are many scenarios, additional time will be needed when using CMAQ. To calculate the results of reduction scenarios within a reasonable time, an analysis formula was used to build an RSM system based on the results of CMAQ. The RSM experimental design covers a change in the baseline emissions of zero to 400 percent, utilizing a staged Latin Hypercube statistical method [17]. The detail of choosing the RSM control variable and building control matrix have been described in a previous study [26]. A control matrix defines the multi-dimensional experiments consisting of a set of emission control scenarios parameterized by control variables [28].
Many emission reduction scenarios were simulated, but only after the baseline scenario conformed to the requirements of Taiwan's air quality simulation standards. In the third step, high-dimensional Kriging [28] was used with Equation (1) to construct the air quality modeling database: In this equation, β is a d × 1 vector for the unknown regression coefficients; F is an n × d matrix of regression functions for the training data; z(x) is the covariance of a Gaussian stochastic process. In the derivation of z(x), → R is the n × 1 correlation vector of γ n 0 , and the various functions → γ T 0 and Y n are the process simulations of Y x 0 and y n , respectively.

SMAT
The function of the SMAT module is to calibrate the simulation results. SMAT estimates a future design value (DVF) at a monitoring site using the air quality model data and observation data from the base year to construct the relative response factors (RRFs) [15,28,29]. DVB is the base design value monitored at the monitoring site. The aforementioned algorithm may be summarized as Equation (2):

BenMAP
Once the pollutant reductions that result from the implementation of some pollution control measures have been modeled using the aforementioned modules, the BenMAP module of the ABaCAS-Taiwan framework can be used to estimate the consequent health benefits of these improvements in air quality. BenMAP is a mature tool for assessing the health benefits of improvements in air quality, and has been employed in many countries [9,22,23,[30][31][32][33][34].
BenMAP is an assessment tool based on the IPA framework [19,20,33]. Three types of technical parameters are required for BenMAP analysis: (1) The results of pollutant dispersal simulations, (2) health impact functions, and (3) monetization functions. In this study, the results of pollutant dispersal simulations were mainly derived from the simulation results of the RSM and SMAT modules. The change in health impact was evaluated using Equation (3), which is based on the BenMAP methodology: In this equation, ∆Y is the expectation value of the change in health events, with Y 0 being the probability of health events in the baseline scenario; β is the literature-derived coefficient of estimation of the health impact function, and it is used to gauge the dependence of health events on pollutant concentrations; Pop is the size of the affected population. Equation (3) can be used to convert changes in pollutant concentration into an expected value of health impact, in units of occurrences. Numerous studies have been conducted to estimate the β value of each health event. In BenMAP, the β values obtained in each study can be unified into a representative β value through a meta-analysis of the pooled data. The unified β may then be used to assess health impacts [20]. In this study, a random-effects meta-analysis was performed to unify the β value.
Finally, the economic cost of pollution can be estimated in BenMAP by monetizing the health impacts using Equation (4). Decreases in pollutant concentration will reduce the expected health impact, which then increases health benefits in the monetized assessment. Conversely, a rise in pollutant concentration will increase health costs: In Equation (4), Health Impact is the expectation value of changes in the occurrence of a certain health event and is given by Equation (3); Value of Health Impact refers to the monetized metric of this health event. The health impacts of air pollution generally include changes in morbidity and mortality risk. However, Liou [35] noted that reductions in mortality risk accounted for over 98% of the health benefits that resulted from reductions in air pollution, whereas the reduction in medical costs owing to improvements in morbidity only accounted for approximately 2% of these health benefits. Therefore, this study will only focus on mortality risk when considering the health impact of air pollution. Changes in mortality risk were monetized using the value of statistic life (VSL) metric.

Cost of Pollution Control and Effectiveness of Pollution Reduction
The TAPCAP being implemented by the Taiwan EPA incorporates 14 pollution control measures; these include power sector regulations, installation of pollution control devices in factories, and replacement of heavy-oil boilers with gas boilers. Old diesel vehicles will also be retired, while newer vehicles will be equipped with smoke filters. As the implementation of the TAPCAP began only in 2017, its pollution control measures were only expected to be fully implemented in 2019. Therefore, it was expected that the pollution-reducing effects of the TAPCAP would start being realized in 2019. The technical costs and expected pollution reductions of each of the pollution control measures of the TAPCAP are listed in Table 1.
The 14 measures included in the TAPCAP can be categorized as administrative or technical measures. Administrative measures pertain to the use of legal measures or administrative methods to reduce pollution. In this case, pollution reductions are derived from increments in technical efficiency, rather than the incorporation of pollution control technologies. For this reason, administrative measures do not require expenditure on pollution control devices. The measures that fall under this category include (1) regulation of fugitive dust from construction sites and stockpiles of dust-generating materials, (2) control of fugitive dust from riverbeds, (3) elimination of 1 million two-stroke motorcycles, and (4) introduction of new vehicle regulations. Technical measures require the use of various pollution control techniques, which need additional investments on equipment. These investment costs are defined as the technology cost of pollution control measures.

Dispersion Simulations: Emissions Data
The emission data in this study were obtained from the 9th edition of the Taiwan Emission Data Systems (TEDS), which was published by the Taiwan EPA and uses 2013 as the baseline year. The PM 2.5 , SO x , and NO x contributions of each source of pollution are presented in Figure 1. It is demonstrated that PM 2.5 pollution in Taiwan is primarily caused by construction sites and road dust, which account for 41% of all PM 2.5 emissions. SO x pollution is mainly caused by industrial emissions, which account for 80% of all SO x emissions. The largest contributor to NO x pollution is traffic emissions (49%), followed by factory emissions (41%). Open data from Taiwan Government [36]. 1 The emission totals were obtained from the Taiwan Emission Data Systems (TEDS 9.0) report, which covers Keelung City, Taipei City, New Taipei

Health Benefits: BenMAP Parameter Data
To estimate the health benefits of each air pollution control measure, the following data were included in the BenMAP database: population data, geographic layers, pollution monitoring data, and mortality rate from the National Health Insurance Research Database [38][39][40][41][42][43][44]. A meta-analysis was then performed to calculate the coefficient of estimation of the health impact function.
The VSL is a fatal risk monetization metric that has been used extensively in health benefit assessment studies [45,46]. The basic concept of VSL suggests that people have a willingness to pay (WTP) for the reduction of a certain percentage of fatal risk; VSL represents the summation of the WTPs in the unit of risk [35].

Health Benefits: BenMAP Parameter Data
To estimate the health benefits of each air pollution control measure, the following data were included in the BenMAP database: population data, geographic layers, pollution monitoring data, and mortality rate from the National Health Insurance Research Database [38][39][40][41][42][43][44]. A meta-analysis was then performed to calculate the coefficient of estimation of the health impact function.
The VSL is a fatal risk monetization metric that has been used extensively in health benefit assessment studies [45,46]. The basic concept of VSL suggests that people have a willingness to pay (WTP) for the reduction of a certain percentage of fatal risk; VSL represents the summation of the WTPs in the unit of risk [47].
The estimation of health benefits owing to improvements in air pollution was performed using the value transfer method (VTM) on the VSL derived by Liou [47] for Taiwan in 2014. In the VTM, the value transfers were based on two aspects, the differences in income and consumer prices between the two years. The adjustments for differences in income were performed by substituting the salary income elasticity of the VSL estimated by Liou [47] into Equation (5): In Equation (5), VSL 2019 is the nominal VSL value for 2019, ∈ w is the salary income elasticity of the VSL estimated by Liou [47], and W 2019 and W 2014 are the average monthly salary incomes of Taiwanese workers in 2014 and 2019.
The differences in consumer prices were adjusted using Equation (6): In this equation, RSVL 2019 is the VSL value after consumer price adjustments, while CPI 2019 and CPI 2014 are the 2019 and 2014 consumer price indices (CPIs), respectively.
The empirical data used in this study and their descriptions are shown in Table 2. Health Impact Function (Cr-Function) Meta-analysis was applied to health impact function using a random effect approach. 7

Simulations on the Effectiveness of the Pollution Control Measures
The emissions recorded in January, April, July, and October 2013 were simulated to analyze the seasonal characteristics of air pollution in Taiwan. Based on these results, we then estimated the annual mean of air pollutant concentrations in Taiwan. The simulation included all of Taiwan and East Asia, and the performance of the simulation conformed to the air quality simulation standards established by the Taiwan EPA [50].
By varying the control matrix, the RSM system can be used to adjust various pollutant concentrations simultaneously to provide insight into the effects of pollution control measures on air quality. The performance of the RSM model was validated using the method developed by Ashok et al. [27], i.e., by computing the coefficient of determination (R 2 ) between the RSM and CMAQ models. We applied RSM to the training samples and used four additional CMAQ cases to fit and validate the RSM [14,51]. In this study, the R 2 always ranged between 0.998 and 0.99, while mean bias and mean normal bias ranged between 0.03-0.02 and 0.01-0.04, respectively. Therefore, the results of the RSM simulation are exceptionally reliable (Figure 2). Here, we estimate the changes in PM2.5 concentration that result from each pollution control measure and their corresponding health benefits with the assumption that the meteorological conditions of the target year are equal to those in 2013. The average PM2.5 concentration in Taiwan is 30.5 μg/m 3 . Figure 3 illustrates that the largest reductions in PM2.5 concentration are due to the TAPCAP that occurred in central and southern Taiwan. Between the various pollution control measures, reductions in the number of diesel trucks resulted in the largest difference in PM2.5 concentration (2 μg/m 3 or 6.5%) ( Table 3). The next most significant measures are the port area air quality regulations and power sector regulations, which reduced the average PM2.5 concentration of Taiwan by 0.5 μg/m 3 and 0.4 μg/m 3 , respectively. This result is consistent with the findings of Lai et al. [51], which indicated that the control of road traffic emissions is highly effective in reducing PM2.5 concentration and that it is necessary to simultaneously control multiple sources of PM2.5 to maximize reductions in PM2.5 pollution. Here, we estimate the changes in PM 2.5 concentration that result from each pollution control measure and their corresponding health benefits with the assumption that the meteorological conditions of the target year are equal to those in 2013. The average PM 2.5 concentration in Taiwan is 30.5 µg/m 3 . Figure 3 illustrates that the largest reductions in PM 2.5 concentration are due to the TAPCAP that occurred in central and southern Taiwan. Between the various pollution control measures, reductions in the number of diesel trucks resulted in the largest difference in PM 2.5 concentration (2 µg/m 3 or 6.5%) ( Table 3). The next most significant measures are the port area air quality regulations and power sector regulations, which reduced the average PM 2.5 concentration of Taiwan by 0.5 µg/m 3 and 0.4 µg/m 3 , respectively. This result is consistent with the findings of Lai et al. [52], which indicated that the control of road traffic emissions is highly effective in reducing PM 2.5 concentration and that it is necessary to simultaneously control multiple sources of PM 2.5 to maximize reductions in PM 2.5 pollution.

Reduction in Health Risk
In this study, long-term health effects (i.e., changes in mortality risk) were used as the metric for quantifying improvements in health risk. According to the simulation, the population density of Taiwan is 644 people/km 2 , and the implementation of the 14 air pollution control measures in the TAPCAP will reduce the average PM2.5 concentration of Taiwan by 3.7 μg/m 3 , thus preventing 26 deaths every 100,000 people. The most beneficial measure is the "retirement of Stage 1 and Stage 2 diesel trucks," as it is expected to prevent the deaths of 3846 (994-9415) people. The next most beneficial control measures are "the strengthening of port area air pollution regulations" and "power facility regulations," which are expected to prevent the deaths of 994 (255-2430) and 827 (213-2022) people, respectively. The values presented in the parentheses represent the 90% confidence interval of the expected reduction in deaths.
In the PM2.5 concentration difference map (Figure 3a) and the avoided deaths map (Figure 3b), the largest changes in PM2.5 concentrations are observed in central and southern Taiwan, whereas the most significant improvements in health risks are observed in the northern and southern cities of Taiwan. This implies that the effectiveness of air pollution control strategies also depends on population density, in addition to the magnitude of the changes in pollutant concentration.

Reduction in Health Risk
In this study, long-term health effects (i.e., changes in mortality risk) were used as the metric for quantifying improvements in health risk. According to the simulation, the population density of Taiwan is 644 people/km 2 , and the implementation of the 14 air pollution control measures in the TAPCAP will reduce the average PM 2.5 concentration of Taiwan by 3.7 µg/m 3 , thus preventing 26 deaths every 100,000 people. The most beneficial measure is the "retirement of Stage 1 and Stage 2 diesel trucks," as it is expected to prevent the deaths of 3846 (994-9415) people. The next most beneficial control measures are "the strengthening of port area air pollution regulations" and "power facility regulations," which are expected to prevent the deaths of 994 (255-2430) and 827 (213-2022) people, respectively. The values presented in the parentheses represent the 90% confidence interval of the expected reduction in deaths.
In the PM 2.5 concentration difference map (Figure 3a) and the avoided deaths map (Figure 3b), the largest changes in PM 2.5 concentrations are observed in central and southern Taiwan, whereas the most significant improvements in health risks are observed in the northern and southern cities of Taiwan. This implies that the effectiveness of air pollution control strategies also depends on population density, in addition to the magnitude of the changes in pollutant concentration.

Health Benefits
The health improvements resulting from each measure were monetized based on VSL, and the monetized results are shown in Table 4. The results demonstrate that the 14 measures of the TAPCAP require an investment of 295.4 billion NTD. The implementation of these measures is expected to provide an average of 2570.5 billion NTD/year in health benefits, as compared with the scenario where these measures are not implemented. After the costs of these measures have been deducted, the net benefit is 2275.1 billion NTD. The benefit-cost (B-C) ratio of the TAPCAP is then 8.7, which indicates that each NTD of investment in pollution control creates a benefit of 8.7 NTD. Based on the 2019 Gross Domestic Product (GDP) of Taiwan, the net benefits of the TAPCAP are worth 12% of Taiwan's GDP. These results show that overall, the advantages of implementing the TAPCAP far outweigh its disadvantages for Taiwan. Therefore, this strategy should be implemented.
In the next step, we will inspect the benefits of each type of measure. The 14 control measures can be classified into two categories based on their attributes; administrative measures and technical measures. There are four administrative measures, denoted as M1-M4 in Table 4, and the health benefits of each of these measures are illustrated in Figure 4. The implementation of these four measures will yield a total benefit of 210.3 billion NTD/year. The tightening of vehicle standards is the most beneficial measure (benefit: 75.8 billion NTD), followed by the control of fugitive dust from riverbeds (benefit: 68.5 billion NTD), control of fugitive dust from construction sites and dust-generating material stockpiles (benefit: 64.2 billion NTD), and promotion of electric vehicles (up to 2100 vehicles) for the transportation of fresh produce (benefit: 1.8 billion NTD).
In the TAPCAP, there are 10 technical measures, denoted as T1-T10 in Table 4, and the benefits of each of these measures are illustrated in Figure 5 are remarkably cost-effective, they should be prioritized for future implementation. However, there is one technical measure that has a net benefit lower than 0 (B-C ratio lower than 1). This is the regulation of boiler facilities, where the government seeks to reduce air pollution by providing subsidies to retire 5000 industrial boilers and 1000 commercial boilers. The government has invested 54 billion NTD on this measure, but the expected health benefit is only 41.6 billion NTD. Therefore, this measure could be improved in terms of cost-effectiveness.  In the TAPCAP, there are 10 technical measures, denoted as T1-T10 in Table 4, and the benefits of each of these measures are illustrated in Figure 5

Summary and Conclusions
The ABaCAS-Taiwan assessment framework was used in this study to perform a comparative analysis between the costs and health benefits of the Taiwan TAPCAP being implemented by the government. Our empirical analysis indicates that the implementation of the TAPCAP has resulted in a net benefit (cost < benefit). Therefore, this ex post facto analysis provides evidence that the TAPCAP is a cost-effective policy. Furthermore, we have calculated the health benefits of each of the 14 pollution control measures that comprise the Air Pollution Control Action Plan (APCAP) and we computed their net benefits and B-C ratios by comparing their costs with the benefits. This was undertaken to demonstrate whether these measures should be implemented (i.e., whether they have a net benefit greater than 0), and allows them to be compared in terms of cost efficiency (by comparing their B-C ratios). These results will serve as a useful reference for policymakers deciding on future pollution control measures. The policy implications of these results include the following points.
All 14 pollution control measures can be categorized into administrative and technical measures. The administrative measures are implemented by strengthening regulations and controls to realize pollution reductions that require administrative rigor. As these measures do not require additional expenditure, they enable pollution reduction to be realized at a relatively low cost. The implementation of these administrative measures will yield a total benefit of 210.3 billion NTD/year. The tightening of vehicle standards is the most beneficial measure (benefit: 75.8 billion NTD), followed by the control of fugitive dust from riverbeds (benefit: 68.5 billion NTD), control of fugitive dust from construction sites and dust-generating material stockpiles (benefit: 64.2 billion NTD), and promotion of electric vehicles (up to 2100 vehicles) for the transportation of fresh produce (benefit: 1.8 billion NTD). Therefore, we suggest that administrative pollution control measures be prioritized for planning and execution.
In terms of technical control measures, the total health benefits of implementing these measures are 2360.1 billion NTD, and the net benefit is 2064.8 billion NTD after accounting for costs. The three most beneficial measures are (1) the retirement of 80,000 Stage 1 and Stage 2 diesel vehicles (benefit: 1401.9 billion NTD), (2) ship speed reductions, ship fuel usage regulations, and the promotion of shore power (benefit: 362.3 billion NTD), and (3) power facility regulations (benefit: 301.4 billion NTD). The relative importance of the technical measures can be decided based on their B-C ratios. The technical measures with higher B-C ratios should generally be prioritized for implementation, as long as there exists an opportunity for the resulting actions to reduce pollution. In the future, policymakers should utilize existing B-C ratio datasets to create budgets and decide on the

Summary and Conclusions
The ABaCAS-Taiwan assessment framework was used in this study to perform a comparative analysis between the costs and health benefits of the Taiwan TAPCAP being implemented by the government. Our empirical analysis indicates that the implementation of the TAPCAP has resulted in a net benefit (cost < benefit). Therefore, this ex post facto analysis provides evidence that the TAPCAP is a cost-effective policy. Furthermore, we have calculated the health benefits of each of the 14 pollution control measures that comprise the Air Pollution Control Action Plan (APCAP) and we computed their net benefits and B-C ratios by comparing their costs with the benefits. This was undertaken to demonstrate whether these measures should be implemented (i.e., whether they have a net benefit greater than 0), and allows them to be compared in terms of cost efficiency (by comparing their B-C ratios). These results will serve as a useful reference for policymakers deciding on future pollution control measures. The policy implications of these results include the following points.
All 14 pollution control measures can be categorized into administrative and technical measures. The administrative measures are implemented by strengthening regulations and controls to realize pollution reductions that require administrative rigor. As these measures do not require additional expenditure, they enable pollution reduction to be realized at a relatively low cost. The implementation of these administrative measures will yield a total benefit of 210.3 billion NTD/year. The tightening of vehicle standards is the most beneficial measure (benefit: 75.8 billion NTD), followed by the control of fugitive dust from riverbeds (benefit: 68.5 billion NTD), control of fugitive dust from construction sites and dust-generating material stockpiles (benefit: 64.2 billion NTD), and promotion of electric vehicles (up to 2100 vehicles) for the transportation of fresh produce (benefit: 1.8 billion NTD). Therefore, we suggest that administrative pollution control measures be prioritized for planning and execution.
In terms of technical control measures, the total health benefits of implementing these measures are 2360.1 billion NTD, and the net benefit is 2064.8 billion NTD after accounting for costs. The three most beneficial measures are (1) the retirement of 80,000 Stage 1 and Stage 2 diesel vehicles (benefit: 1401.9 billion NTD), (2) ship speed reductions, ship fuel usage regulations, and the promotion of shore power (benefit: 362.3 billion NTD), and (3) power facility regulations (benefit: 301.4 billion NTD). The relative importance of the technical measures can be decided based on their B-C ratios. The technical measures with higher B-C ratios should generally be prioritized for implementation, as long as there exists an opportunity for the resulting actions to reduce pollution. In the future, policymakers should utilize existing B-C ratio datasets to create budgets and decide on the appropriate combination of measures to maximize the cost-effective of the pollution control strategy. In addition, our findings demonstrate that government-subsidized decommissioning of boilers incurs higher costs than health benefits; this demonstrates that the cost-effectiveness of this measure needs to be improved. We suggest that the subsidies for this measure be adjusted to enable cost-effective pollution reduction to be realized.
Further research should be performed in two directions. First, several international technical parameters that exist in the ABaCAS-Taiwan framework have yet to be localized for Taiwan. Thus, a future study could involve updating the framework with locally appropriate technical parameters to improve the accuracy and rationality of the framework's estimations. According to previous studies, the reduction of expected deaths caused by air pollution improvement can cause a positive effect on macroeconomics through increased labor force. These positive economic effects can be simulated using macroeconomic models, such as the computable general equilibrium model. Therefore, we propose further study to incorporate the economic models to investigate how air pollution levels could affect the economy as a whole through the labor market.
As the framework includes the ability of reduction benefit estimation, any new control measure could be examined and then implemented or declined. The findings of this study suggest that ex post facto analysis as well as the future APCAP could use ABaCAS as a regular estimation tool. According to air pollution policymaking processes in many countries, the ABaCAS system can be adopted as a powerful tool. The case study of the ABaCAS-Taiwan demonstrates that it can already estimate the impact of air pollution on populations, however, future studies could use economic models to analyze how changes in air pollution affect the overall economy. The methodology used in this study can be extended to countries other than Taiwan, especially for countries that the air quality is closing to the target, they can build up the local datasets including emission inventory, control technology with its cost, and human health benefit at first, then using ABaCAS to evaluate the performance of air quality policy.