Coseismic Ground Displacement after the M w 6.2 Earthquake in NW Croatia Determined from Sentinel-1 and GNSS CORS Data

: At the very end of the year 2020, on 29 December, a hazardous earthquake of M w = 6.2 hit the area of Petrinja and its surroundings, in the NW of Croatia. The earthquake was felt across the area of 400 km, leaving an inconceivable damage in the vicinity of the epicenter, devastated towns and ruined lives. In order to map the spreading of earthquake waves and to determine the coseismic ground displacement after the mainshock, we have analyzed open satellite radar images of Sentinel-1 and the GNSS data from the nearest CORS station related to the epicenter, along with the seismic faults. In this paper, we addressed and mapped the displacement linear surface ruptures detected by the SAR interferometry. The results show the vertical ground displacement to the extent of − 12 cm in the southern area and up to 22 cm in the north-western part of a wide area struck by the earthquake impact, related to the epicenter. Subsidence and uplift in a range of ± 5 cm over a wider affected area indicate a spatial extent and hazardous impact made by the earthquake. The ground displacement of 30 cm to the West and 40 cm to the East has been identiﬁed considering the intersection of Pokupsko and Petrinja strike-slip fault system in the seismic zone of Pannonian basin. Accordingly, we obtained matching results of 5 cm south-easting shift and − 3 cm subsidence on Sisak GNSS CROPOS station, addressing the tectonic blocks movement along the activated complex fault system. The results compared with the geology data conﬁrm the existence of two main faults; the Pokupsko and the Petrinja strike-slip faults and interpret the occurrence of secondary post-seismic events over the observed area.


Introduction
In addition to damages caused by hazardous earthquake, another significant repercussion of earthquake is land displacement. Most visible deformations are found over the faults forming surface ruptures. Nevertheless, the displacements invisible to the naked eye but still occurring are the ground displacements that can be determined by surveying techniques. Since the displacements can result in shifts on the scale from millimeter to meter, they are relevant to be observed and estimated.
Optimal estimation of surrounding area displacement can be made by precise leveling, static GPS measurements and other precise geodetic field works. However, the mentioned techniques are time-consuming and always challenging in terms of funding. In the meantime, until the field works are carried out, satellite images are of a great relevance providing almost immediate first response to such occurrence.
In the last decade, Satellite Aperture Radar (SAR) has become a well established measurement technique, suitable for different applications due to its possibility to observe and record the Earth surface regardless of the weather or clouds. The satellites equipped with SAR record images of the Earth's surface by emitting radar signal along the radar's beam line of sight (LOS) [1]. SAR satellites are continuously circling around the globe, in the ascending and descending orbits, providing multiple spatio-temporal images that provide thousands of images over the same area in different time periods. Repetition of images over an identical area results in detection of land changes. A significant property of the SAR technology is the phase value. Throughout the phase information mapped on the interferograms, deformations due to large earthquakes can be detected and main faults revealed. Some of the studies mentioned in [2] use SAR interferometry (InSAR) to detect the displacement related to land subsidence [3], earthquakes ( [4][5][6]), highway deformation [7] and similar land displacements ( [8], anthropogenic deformation phenomenon [9,10]), or urban change ( [11,12]). It has also been proved by a recent study [13] that InSAR measurements produce noise, but the noise can be reduced without the loss of significant data information by applying the processing techniques. Many recent studies have focused to the usage of SAR technology in the estimation of ground deformation after large earthquakes: Reference [14] estimated the land displacement but without detecting the active major faults; Reference [15] highlighted the need to consider the coherence change analysis and identify the limitations of the SAR applications; others ( [16][17][18][19][20]) estimated earthquake's impact assessment based on the data derived from SAR. Furthermore, the SAR technique is now used for the study of earthquakes and has been applied around the World ( [21][22][23][24][25]) and in Europe ( [26][27][28]).
Considering the mentioned recent studies and parameters to be considered in appliance of SAR images for earthquake's impact assessment, the area of interest in this study is free of heavy vegetation, and the coherence maps were used to minimize the atmosphere effect. In this paper, we present the usage of multiple SAR satellite images acquired in the period before and after the earthquake, in order to map the ground deformation and displacement caused by the earthquake of magnitude M w = 6.2. The output of SAR interferometry is LOS displacement that can be converted to vertical and west-east displacement, estimating the ground displacement. Therefore, we have analyzed SAR and GNSS data and compared them to geological data, confirming the existence of two main faults over the affected area and deriving the estimation of surface deformation of the surrounding area.

Geodynamic Framework
The Republic of Croatia is a member country of the European Union situated in the southern part of Europe, on the eastern coast of the Adriatic Sea. As for its location, the country lies in a very seismically active area due to continuous movement of the Adriatic litospheric microplate to the North [29]. Although Croatia comprises five different tectonic settings: the Pannonian Basin, the Eastern Alps, the Dinarides, the transition zone between the Dinarides and the Adriatic plate, and the Adriatic micro plate itself [30], it has been divided in 17 seismic zones for a detailed assessment of the seismic hazard [31], shown in Figure 1. Additionally, the faults across Croatia, derived from the European Database of Seismogenic Faults (EDSF), model FSBG V6.1 [32], are presented in the Figure 1. Seismicity source in Croatia is mainly twofold: On its coastal side, the country lies on the border of Micro Adriatic tectonic plate [33] and the mountainous chain of the Dinarides which collide [34,35] while on the inland country side, the active faults cross over the middle part of the country and belong to the Pannonian Basin fault zone. , is derived from [36], while the faults are derived from EDSF project, model V6.1 [32], and seismic zones from [31]. Topography is generated from the 1 arc second SRTM [37], with Open Street Maps in the background.
Micro Adriatic tectonic plate and its movement have not been completely discovered yet. Although it was first mentioned by McKenzie in 1972 [38], the first far-reaching geodetic researches of its movement were made in the 90s. Ward [39] made the first space geodetic measurements of the Adriatic micro plate using VLBI data. Other studies (Calais et al. [40], Battaglia et al. [29], Grenerczy et al. [41], Serpelloni et al. [42] D'Agostino et al. [43], Devoti et al. [44], Marjanovic et al. [45]) analyzed the movement based on GPS measurements but with different approaches: Their divergence was about the size of the plate and the position of the pole of rotation for velocity vector. The latest studies predict convergence of the Adriatic micro plate in the Dinarids at a rate of velocity vectors of <5 mm/yr [46]. Regarding the position and the size of the Adriatic micro plate, Ollier [47] recently tried to determine it, but he found it too complex to be determined. Instead, he has defined it as a consistent block, surrounded by the Apennine-Adriatic-Dinarids block, not supporting the idea of the plate floating northwards or the idea of its collision in the zone between the Africa and Europe. Hence, the Adriatic micro plate exists, it has its own movement, the studies determine its velocity vectors, but its final size is still not known. Recent studies ( [33,48,49]) agree upon the thesis that the micro Adriatic plate is responsible for a present tectonic evolution of mountainous area of the Dinarides along the Croatian coast.
In the middle continental part of the country, a fault running through the country is a southern marginal fault of the Pannonian Basin [50] which continues to run southward to Banja Luka fault in Bosnia and Herzegovina. The Pannonian Basin is often neglected since the most seismic events do occur at the coastal part of Croatia, and there is no record of strong earthquake on that area until XIX century. First recorded earthquake greater than VII MCS happened in 1861 [51]. However, the Pannonian fault area has become well known in the seismic community due to Mohorovičić research made exactly in that area after the Kupa valley earthquake in 1909. At that time, Mohorovičić proved the existence of a boundary-level Moho discontinuity, between the Earth's crust and its mantle [52]. It was also the time when Mohorovičić proposed a procedure for unique location of earthquake focus and the analytical expression for the increase of elastic wave velocity with depth, so called Mohorovičić's law [53]. Kupa valley earthquake was the strongest earthquake on the Pannonian basin area that occurred before the Petrinja 2020 event. Its epicenter was located 9 km North of Pokupsko with magnitude of M w 5.8, and the hypocentral depth of 14 km [54]. The estimated intensity was VIII• MCS. After that earthquake, over the last 100 years, the magnitude of earthquakes in this area has not been greater than 5.4 on the Richter scale (VI MCS) [31], until December 2020.
The Pannonian fault is characterized by rare occurrence of significant shocks [55]. Markušić et al. [31] attribute it to an intraplate seismicity, while Aljinović et al. [35] and Herak et al. [56] defined tectonic movements in the area of Pannonian Basin as predominantly vertical on steeply dipping faults. The common properties of previous earthquakes on this area are that the epicentral area elongates NW-SE. Herak et al. (2009) in [57] assumed, by observing historical earthquakes of 1861 and 1909, that future earthquake could generate fault corresponding either to NW-SE striking dextral or NE-SW striking sinistral fault set, and when reactivated, the fault zone would invert accommodating dextral and reverse motions due to recently NE-SW directed compression in this region.

Seismicity of Croatia
Regarding the geodynamic framework, the coastal part of Croatia is the most seismically active one. In historical records, the Dubrovnik area was the most seismically active area, with even 8 seismic events greater than IX MCS [53], out of which the strongest earthquake occurred in 1667, with intensity X MCS. Nevertheless, there have been other significant earthquakes along the Adriatic coast in the 15th, 16th, and 18th centuries. During the last decades, also significant seismicity in the Central Adriatic has been noticed due to the increase in quality and number of regional seismological stations [53]. Considering the most populated area, namely the capital city Zagreb and its metropolitan area, large number of strong earthquakes occurred there in the 17th century [53], of which the largest one had an intensity of M w 6.3, occurring in 1880 in Zagreb.
Considering the seismicity in Croatia from 1900, all significant earthquakes with M w > 5 (Biokovo earthquake in 1962 with M w 6.1, Ston-Slano earthquake in 1996 with M w 6.0, and the earthquake sequence on Jabuka island in south Adriatic in 2003 with M w 5.5 [53]) occurred in the south Adriatic, except the Kupa Valley earthquake, occurred in Pannonian basin in 1909. Figure 2 displays the earthquakes that happened in the last 16 years, in the period between 2004-2021, over Croatian territory. The time span has been set to the last 16 years due to available seismic data distributed publicly by the European-Mediterranean Seismological Centre (EMSC) [58]. Left subfigure shows the earthquakes that happened in period between 2004 and December 2020, while the subfigure on the right side shows the earthquakes that happened in the period between 15 December 2020 and 1 February 2021. The main aftershocks are occurring along the NW-SE direction, following the Pannonian fault location (see Figure 2, subfigure on the right, orange dots).
In the last 16 years until December 2020, more than a thousand seismic events happened on the Croatian territory, out of which about 25% were of magnitude M w 2.5. Furthermore, in that period, there have been 19 (data by EMCS) occurrences of earthquakes M w 4 and only one M w > 5. This M w 5.4 earthquake was also a hazardous earthquake with the epicenter near the Croatian capital city, also dating from 2020 (March), which caused human loss and enormous material damage [59].

Study Area
The Pannonian fault is situated between 45 • and 45.6 • N (see in Figure 2) and 16 • and 17 • E, as shown in Figure 2 and its dangerous seismic potential is often ignored since most of the seismicity is (3 >= M w <= 4) is distributed along the Croatian coast ( Figure 2), and the Pannnian basin is considered as a low seismic risk zone by recent seismic risk maps of Croatia ( [60,61]).
However, on 29 December 2020, Croatia was hit by one of the most hazardous earthquakes in its seismic history, M w 6.2 on the Richter scale. According to [62], the earthquake's intensity can be described by primary and secondary effects via the Environmental Seismic Intensity scale (ESI) 2007. Considering the ESI scale [62], Petrinja earthquake belongs to the IX-destructive type of earthquake, since the ground ruptures developed up to a few km long with offset of about several cm as a primary effect, and as secondary effect, significant cracks in paved road-shave, liquefaction, cracks and fissuring occurred in a diameter of 10 km related to the epicenter.
The tremor occurred at a depth of 6 km [54]. A day before the mainshock, there were two major events of M w 5.2 (28 December 2020 at 05:28) and M w 5.0 (28 December 2020 at 06:49) that were considered as a mainshock until the 29th. The analysis of the possible preceding events related to the mainshock on the 29th and the main foreshock on the 28th showed that during the one year period prior to the mainshock, there had been only one event exceeding the magnitude of two Richter scale (M w 3.0), in August 2020. Two events greater than magnitude two Richter (M w 2.0 and M w 2.8) occurred on the day of the mainshock, but regarding the earthquakes of the magnitude around 5 the day earlier, these two events were classified as a normal events following the major shocks while it was still believed that the mainshock was the one of the magnitude M w 5.2.
In the following month after the mainshock until the 1 February, numerous aftershocks occurred in the affected area, more than a thousand of them altogether still occurring at a rate of few of them per day. Most of the earthquakes which occurred after the mainshock had a magnitude bellow M = 2.5, 9 of them exceeded the magnitude M = 4, and one out of those nine was stronger than M = 5 on the Richter scale, on 6 January 2021. The scattered occurrence of aftershocks' magnitudes can be seen in Figure 3, where it is also visible that the trend of afterquakes' weakened frequency and magnitude as time passed.

Data and Methodology
On 29 December 2020, a strong earthquake M w 6.2 hit near Strašnik village in the NW Croatia [63]. The tremor occurred at a depth of around six kilometers, with intensity at the epicenter of VIII EMS scale, occurring on the intersection of longitudinal NW-SE right-lateral and transverse NE-SW left-lateral faults along the transitional contact zone of the Dinarides and the Pannonian Basin [54]. All significant institutions for earthquake detection registered and processed the data of the earthquake. In a recent paper [54], Figure  4 shows the focal parameters of the earthquake determined by the INGV [64] and the USGS that describe it as a result of shallow strike-slip faulting within the Eurasia Plate [65]. In order to map the event of this earthquake and its effects on the ground displacement in the area affected by the earthquake, we analyzed the multiple spatio-temporal Sentinel-1 satellite C-SAR (C-band synthetic aperture radar) images and the continuous s GNSS data of the nearest reference station.

SAR Data
Sentinel-1 is the first mission of a Copernicus initiative, the European initiative for online dissemination of global satellite data free of charge. Copernicus is the European Union's Earth observation program fully operated since 2014 [66]. It is a joint program coordinated in partnership between the European Commission, European Space Agency (ESA), the EU Member States, and EU agencies providing an open information service with satellite and non-satellite Earth observation data. Sentinel-1 has two polar-orbiting satellites: Sentinel-1A and Sentinel-2B launched in 2014 and 2016, respectively. The Sentinel mission has four modes of distribution of its data. We chose the Interferometric Wide Swath (IWS) mode. Overall coverage of one Sentinel image in IWS mode is 250 km swath, 5 × 20 spatial resolution [67]. Each Sentinel-1 IWS image is referred to as swath and is divided into three horizontal areas called sub-swaths. A sub-swath consists of nine vertical areas called bursts. Each satellite has 12 days revisit time cycle with 175 orbits/cycle. They are circulating around the globe with the path on which they travel from the South to the North belonging to the ascending orbit, while the descending orbit is directed vice versa. Therefore, the Sentinel images can be acquired in an ascending or descending orbit. The Sentinel-1 data products are distributed in three levels shown in Table 1. Since the energy of this earthquake M w 6.2 caused effects on the building stock, such as the collapse of houses and the destruction of towns and villages, and on the natural environment, such as the activation of landslides, it was necessary to evaluate, quickly, the ground displacements of the land, in order to get a ground displacements assessment. For that purpose, we used a Level-1 images of Sentinel-1, Single Look Complex (SLC), partially processed data with preserved phase (see Table 1). Furthermore, since the most advantageous feature of SAR technology is that it enables acquiring images regardless of the clouds or any weather condition, we used interferometric wide (IW) sub-swaths.
Even though SAR satellites record the distance along the radar path, it is not possible to say whether the Earth's surface has moved vertically or horizontally only by using one of the satellite orbits (ascending or descending). The displacement that is identified by SARs corresponds to the spatial displacement vector in the direction of the radar signal. To estimate ground movement, it is necessary to combine both orbits. Therefore, we chose both Sentinel-1A and Sentinel-1B images. Sentinel-1A images were in ascending orbit, in relative orbit number T146, while Sentinel-1B images were in descending orbit, number T124. The two satellites are complementary, each has revisiting time of twelve days mutually spaced apart by six days, which makes it possible to get the images of the area of interest in a time span of six days. For the first stack of before, we have selected Sentinel-1A on 18 December 2020 and Sentinel-1B on 23 December 2020, and for after earthquake state-of-the-art, we used Sentinel-1A on 30 December 2020. and Sentinel-1B on 4 Januray 2021 respectively (see Table 2). These images were the only ones available for the area of interest at the moment of research, which was in the first week after the earthquake. The images were selected and downloaded via Copernicus Sci Hub data site [68]. Later on, during January 2021, we downloaded two more pairs of corresponding images ( Table 2) in order to analyze land displacement after the series of earthquakes. We conducted a well established procedure for interferometry processing [69] in a Sentinel Application Platform (SNAP), European Space Agency's (ESA) open toolbox for Sentinel analysis [70]. Our sequence of processing is given in a Figure 4. We created interferograms of unwrapped phase for each subswath in case of Sentinel-1A, merged them after debursting, and continued with a single product in differential SAR processing and unwrapping the phase. We did the unwrapping with the SNAP's plugin snaphu outside of SNAP toolbox, but later on, we computed the displacements separately using well known equations for displacement computation from the unwrapped phase (more details in [12,15]). After the determination of the Line of Sight (LOS) displacement, we corrected the values for the topographic correction and finally computed the estimation of vertical ground displacement after the earthquake. The vertical ground displacement was computed by LOS displacement and incident angle θ using the expression ( [71,72]): As for the elevation data for the removal of topographic phase, we used 1 arc second Shuttle Radar Topography Mission (SRTM) [37] digital elevation model (more details on: https://lpdaac.usgs.gov/products/srtmgl1v003/, accessed on 10 Januray 2021).

GNSS CORS Data
To independently assess the results obtained by SAR analysis, we processed the GNSS data obtained at the national GNSS CORS reference station SISA, located on the observed area, in Sisak. SISA station is one of 30 continuously operating reference stations (CORS), belonging to Croatian GNSS network of continuous observing reference stations. CROPOS was established in 2008, with three running services. It provides the accuracy of 2 cm positional and 4 cm in vertical sense for a real-time (RTK) GNSS measurements and subcentimeter accuracy for post-processing [73]. High level of accuracy was achieved on the grounds that it had continuous millimeter stability. Such stability is needed in order to have centimeter real-time positioning and in order to act as a national reference frame for displacement and other geophysical studies.
We downloaded and used daily 30 s interval GNSS measurements from SISA reference station for 10 days before and 10 days after the earthquake. The GNSS measurements were downloaded in RINEX (eng. Receiver Independent Exchange) v. 3.03. format from the GPPS service for the purpose of post-processing. Due to the substantial amount of data, the authors found it appropriate to use the 30-minute interval, and therefore, originally sampled data of 1 s were resampled to 30 s. A period of ten days before and ten days after the earthquake was observed. Median value of ten days prior to the earthquake for each of three coordinates was set as a reference coordinate value for further analysis. Regarding the reference value, the shift in northing, easting, and height direction was computed, given in detail in the next section.

Results
The interferogrammetric phase represents the difference in a recorded signal's distance acquired by two SAR's. It is expressed by wavelength, and it can be mapped on interferogram. Each visible fringe on the interferogram corresponds to the wavelength unit depending on a band used by the radar. In case of C-SAR images used in this study, the wavelength for C-band is 5.6 cm. Figure 5 shows four interferograms: On the upper left, there is the interferogram for the Sentinel-1A ascending orbit, and on the upper right, there is for Sentinel-1B descending orbit acquired in the period of one week before and one after the earthquake, while on the lower left and right insets the interferograms in the period of weeks after the earthquake have been shown determined from the Sentinel-1A ascending orbit and the Sentinel-1B descending orbit, respectively. Both (a) and (b) interferograms shown in Figure 5 show a good correlation with the signal dominated by deformations, not by atmosphere, orbit, or digital elevation model errors. In that way, the interferogram clearly indicates the existence of the deformation. The slight mutual differences are visible, but it is expected due to different incident angles ranging from 36.24 to 45.78 and 35.03 to 41.73 degrees for Sentinel-1A and Sentinel-1B, respectively. From the after-earthquake state-of-the-art interferograms, shown in (c) and (d) insets of Figure 5, the deformation is still visible but on the smaller scale, implicating that the ground displacements are still occurring as the ground continuously trembles a month after the earthquake.
By unwrapping the interferometric phase, we obtained the displacement in line of sight (LOS) of the SAR radar. Although it is expected for the inverse orbits when analyzed separately to yield different results with mutually inverse sign, it is still interesting to see ( Figure 6) the significant differences obtained: Amplitude of LOS displacements obtained by the Sentinel-1A has the range of 74 cm unlike the one obtained by the Sentinel-1B with the range of 53 cm. LOS displacement is not a value that expresses the exact ground movement of the Earth's surface, but it reveals the existence of land motion. By combining the inverse orbits and having in mind that the SAR is more sensitive to vertical motion than to horizontal, vertical movement can be roughly isolated and determined.
On 9 January 2021, while we were working on this research, the Croatian Geological Institute (CGI) released their new findings [74] about the earthquake, mapping the direction of two faults that are intersecting near the epicenter of this earthquake. The NW-SE fault defined by Croatian Geological Institute is in accordance with the ESDF global Faul Model V6.1, but somewhat eastwards. It is obvious that both sources (ESDF V6.1 and CGI's faults) have the same fault mapped, but we assume that the global model is a rough estimate, and CGI is a more precise one due to thorough regional measurements made by CGI. Hence, we included the newly mapped faults of Pokupsko fault (stretching NW-SE) and Petrinja fault (stretching SW-NE) determined by Tvrtko Korbar from CGI [54,74]. The two faults are dividing the area distressed by the earthquake in four quadrants. The faults can be clearly recognized from the LOS displacements in the period of the week before and after the mainshock, registered by the SAR satellite, seen in Figure 6. Based on Equation (1), we made an estimation of the Earth's surface ground displacement, in vertical up-down and horizontal east-west direction. The computation was made using LOS displacement incident angle values [14] at every pixel prior to conducting the terrain correction. During the DinSAR processing, pixel size was set to 27 m. Incident angle was obtained from the corresponding SAR images, ranging from 36.24 to 45.78 and 35.03 to 41.73 degrees for Sentinel-1A and Sentinel-1B, respectively. The values of computed ground displacement differ from LOS displacement values by 30% and 50% for vertical and horizontal displacements, respectively, as seen in Table 2. This relation between the LOS and ground displacements corresponds to similar studies [71], where authors have used fixed value for the incident angle and therefore got the enlargement of 20% in favor of vertical displacement regarding the LOS displacement. However, for the purpose of this study conducted on a relatively small area, it was found necessary to use origin pixel values of incident angle to estimate behavior of ground deformation as much as possible with SAR data. During the January 2021, we acquired subsequent time-series of SAR images (see Table 1) and analyzed the behavior of the ground movement in the weeks following the mainshock. We corrected the displacement for the coherence factor of <0.4, eliminating the noise signal and giving the true insight in the most significantly affected areas. We have analyzed four pairs of subsequent images from both orbits, but the ground movement is visible only on the first pair taken shortly prior and after the earthquake. Despite the fact that more than a thousand aftershocks happened during January (see Figure 3), the images acquired in the month following the mainshock show neglectable ground displacement of only few millimeters, while the first pair of images clearly identifies Petrinja town as the most displaced one, shifted up to 40 cm to the east (see Figure 7), situated on the eastern part of the Pokupsko fault. On the western side of Pokupsko fault and on the side of the epicenter, the displacement toward the West is visible with the greatest shift of 60 cm luckily mainly in the uninhabited area, reaching Glina city at its borders. Majske poljane is the village that has been razed to the ground. The Figure 8 gives an insight: Majske poljane is located over the Petrinja fault where there was also the epicenter is located. This is the area mostly affected by the western displacement of Pokupsko surface rupture. The twofold impact made an immense damage both in Majske Poljane and Petrinja.
Dominant impact of the earthquake on horizontal movement is visible from the computed east-west ground displacement shown in Figure 8. Moreover, the enlargement of the horizontal displacement related to LOS displacement implies such a conclusion. Taking into account that SAR images show the movement relative to satellite position and are not referenced to fixed ground point, ground displacements obtained from the SAR can be used for the interpretation and indication, not as an absolute determination of the displacement.   The vertical displacements range between −12 cm and 22 cm stretching over the earthquake stricken area (see Figure 9). The spatial split between the land subsidence and the land uplift follows the directions of Pokupsko and Petrinja strike-slip faults mapped by Croatian Geological Institute [74]. Vertical displacement is mostly expressed in the western quadrant; on the other hand, the displacement across the faults themselves is minimal. However, we find the increased values of displacement on the western and southern quadrant relatively expected due to topography indented in that area. On other hand, in the northern and eastern quadrant, the displacement is lower than the topography regarding the faults of Pokupsko and Petrinja, but there is still a displacement range of ±5 cm suggesting a real ground movement related to the earthquake and independent of topography also in a wider affected area. The results of the horizontal west-east displacement coincide with the recently published GNSS field measurements [75]. Comparing the results from [75] with the results of the SAR analysis, the ground displacements around the epicenter are the resultant vector of two identified strike-slip faults: Pokupsko and Petrinja, as seen in Figure 9. The results of analyzed GNSS data show that there has been a significant shift of SISA station of 5 cm towards the East and 2 cm to the South (see Figure 10). The eastern shift coincides with the results we obtained from the SAR analysis, while the north-south direction is not straightforward in SAR processing since SAR technique is more sensitive to horizontal east-west shift neglecting the north-south shift since the orbit path stretches along the north-south direction. As for the height, the SISA station shows subsidence up to 3 cm, as seen in Figure 11, which is the complementary result obtained by the SAR analysis: The identical displacement is obtained at the location of SISA station when vertical displacement is derived from SAR analysis, shown in Figure 9. Considering the geological field data acquired after the earthquake, a hundred sinkholes [76] opened as one of the extreme post-seismic near-surface effects [54] in a small place Mečenčani, located on a south-east line of Pokupsko strike-slip faults, as shown in Figure 9. Comparing the vertical displacements results obtained by SAR analysis and the geological occurrence of sinkholes, it is visible from Figure 9 that the impact on the vertical dimension was the strongest on the west side of Pokupsko strike-slip fault, reaching −6 cm subsidence over the Mečenčani area, probably activating the occurrence of sinkholes. Figure 10. The graph shows two-dimensional displacement of a CROPOS's SISA station due to the earthquake, with ten blue dots representing SISA's location ten days before the earthquake and ten red dots the position during ten days after the earthquake. Figure 11. The graph shows positional (Northing and Easting) and vertical (Height) displacement of a GNSS CORS CROPOS station SISA located 30 km from the epicenter. Blue color represents the state before the earthquake and red color after the earthquake.

Conclusions
The work presented in this paper was focused on the hazardous earthquake of M w = 6.2 that happened in NW Croatia on 29 December 2020. The research was conducted on a real time basis as the Sentinel images were getting available.
By combining the ascending and descending orbits, we estimated the ground displacement over the affected area. The left-lateral and right-lateral surface shifts are visible from the ground displacement maps derived from SAR Sentinel-1 data. Horizontal ground displacement is around 30 cm to the West and 40 cm to the East, shifting to the East and to the West related to Pokupsko strike-slip fault, while vertical displacement has overall range amplitude of 35 cm, most pronounced along Hrastovička gora, the mountainous area on the western side of Pokupsko fault also stretching in the NW-SE direction. Although the majority of foreshocks and aftershocks occurred along the Pokupsko fault, the impact of this complex tectonic setting is visible from the obtained vertical and west-east ground displacements, which are not one-way oriented, but on the contrary, they are dispersed unevenly around the intersection of Pokupsko and Petrinja strike-slip faults. We found the highlighted subsidence of −12 cm in the southern area and an uplift of 22 cm in the north-west area as highly correlated and partially influenced by topography which is indented over that area. However, the whole area distressed by the earthquake is facing vertical displacement in the range of ±5 cm, which we found causes a significant impact on activating the sinkholes at the south-east line of Pokupsko strike-slip fault.
The GNSS analysis has yielded the results compliant to the SAR analysis, clearly showing vertical subsidence of 3 cm in the area of Sisak and horizontal displacement of 5 cm to the south-east. Maximum east-west horizontal displacement of GNSS CORS CROPOS station follows the direction of a resultant vector of Pokupsko and Petrinja fault movement, NW-SE Pokupsko fault striking dextral and NE-SW Petrinja fault striking sinistral, confirming the complex tectonic setting at the intersection of these two strike-slip faults.
Based on the conducted multi temporal SAR analysis, this research confirmed the existence of two surface ruptures, Pokupsko and Petrinja strike-slip fault, seen by separating line, being the boundary line of the area where the ground displacements towards east and west occur. The results are compliant with the recent study of [54], identifying the dextral coseismic strike-slip displacement along the Pokupsko fault and the sinistral strikeslip displacement along the Petrinja fault. However, this research is important since the estimated ground displacements identify and explain some of the secondary post-seismic events that occurred over the affected area. Regarding the range of the estimated ground deformations, the future analysis should address the stability of national reference system and the detail accuracy research of real-time GNSS measurements over the affected area.