Relationship between the Intermediate Soil State and Se tt lement Control Measures during Tunnel Construction Undercrossing the Existing Station

: Se tt lement control of existing stations has consistently been a key issue in tunnel construction. Intermediate soil has a signi ﬁ cant in ﬂ uence on the se tt lement of the existing station as a connector between the new tunnel and the existing station which should be considered when selecting se tt lement control measures. To clarify the relationship between the state of the intermediate soil and the se tt lement and control measures of the existing station, this study investigated 49 new tunnel projects under existing stations and elucidated the relationship between the se tt lement and the se tt lement control measures of the existing station and the intermediate soil. The relationship be-tween the failure of the intermediate soil and the se tt lement of the existing station was further analyzed by numerical simulation. Lastly, a simple mechanical model of intermediate soil failure was constructed to determine the stress state of the intermediate soil in constructing a tunnel under the existing station to guide the formulation of se tt lement control measures for the existing station. Hence, when the intermediate soil is completely destroyed, active control measures, such as jack or grouting lifting, should be implemented; when the intermediate soil is partially damaged, passive control measures should be undertaken. Thus, this study can provide a reference for se tt lement control of tunnels under existing stations.


Introduction
With the gradual improvement of the subway system, the number of underpass construction cases has increased [1][2][3][4]. In a new tunnel undercrossing an existing station, the existing station has a large span and complex structure and is prone to settlement, severely affecting its operational safety. Although the settlement control of existing stations is key to underpass construction [5][6][7][8][9][10][11][12], engineering safety problems are likely to occur during its construction [13,14]. Excessive settlement will lead to the local collapse of existing stations [15,16], thereby affecting regular operation and use, while surface ancillary structures will cause settlement collapse damage. In short-distance underpass construction, excavation soil disturbance has an evident influence on the settlement of the existing station. Owing to its limited bearing capacity, the soil cannot support the existing load, thus increasing the settlement of the existing station [17][18][19][20][21][22][23][24][25][26].
Therefore, many scholars have studied settlement control laws and control measures for tunnels under existing stations. Li [27] reported that the jack support method could effectively control the settlement of an overlying tunnel during the construction of an existing tunnel. Wu [28] proposed that the combined pre-support technology of a pipe roof and grouting reinforcement can effectively consolidate the in situ stress and improve the bearing capacity of the soft rock surrounding the rock, which plays a significant role in controlling settlement. Kummerer [29] reported compensation grouting to be an active method that can be divided into two stages: adjusting the intermediate soil and actual grouting, which can offset the settlement caused by tunnel excavation. Focusing on the project of Shenyang Metro Line 9 Olympic East-Olympic Center interval underpassing the existing Olympic Center Station of Line 2, Huo [30] verified the superiority of the CRD method in underpass construction via numerical simulation and simultaneously suggested deep-hole grouting reinforcement and jack-up technologies for the effective control of the settlement of existing structural floors. Through case analysis, field monitoring, and other methods, Zhang [31] clarified the response of an overlying subway station to the characteristics of double tunnels and land subsidence, as well as the importance of jacks in the application of tight underpass engineering. Li [32] compared the freezing method with three other reinforcement methods and reported that the freezing method is better at controlling surface displacement and vault settlement, while the grouting, pipe-shed, and pipe-curtain methods are favorable in controlling surface uplift.
As a connector between the new tunnel and the existing station, the intermediate soil significantly affects the settlement of the existing station. Zheng [33] reported that, when Qingdao underpasses the station, the intermediate soil is slightly weathered granite with a thickness of 4.45 m. The soil parameters were satisfactory, and the existing structural settlement was within a safe range. Zhao [34] found that the gravity load of intermediate soil is partially borne by its self-stability, whereas the remainder is borne by the lower presupport. The lower structure is deformed under the load of the intermediate soil layer. The deformation of the intermediate soil caused settlement deformation of the upper existing structure, which became smaller with an increase in the intermediate soil foundation coefficient. Fu [35] explored the minimum safe construction distance for a new tunnel in an existing structure under different surrounding rock conditions, i.e., the minimum intermediate soil thickness. Hage Chehade [36] analyzed the position of double holes via numerical simulation and found that the soil settlement mode depended on the distance between the tunnels. Shahin [37] analyzed the earth pressure distribution and ground motion around a tunnel during tunnel excavation using finite element analysis, which depended on the distance and position between the two tunnels.
Many researchers have realized that the state of intermediate soil significantly affects the settlement of existing stations; therefore, the state of intermediate soil should be considered when selecting settlement control measures for existing stations. At present, no research has established the relationship between the state of the intermediate soil and the existing settlement control measures, which leads to the choice of settlement control measures to be discussed. To clarify this relationship, the present study first investigated 49 new tunnel projects under existing stations and elucidated the relationship between the settlement and the settlement control measures of the existing station and the intermediate soil. The relationship between the failure of the intermediate soil and the settlement of the existing station was further analyzed via numerical simulation. Lastly, a simple mechanical model of intermediate soil failure was constructed to examine the stress state of the intermediate soil in constructing the tunnel under the existing station to guide the formulation of settlement control measures for the existing station.

Case Analysis
For the analysis, 49 new tunnels beneath existing stations were investigated. Appendix A presents the tunnel construction methods, buried depth of existing stations, geological features, intermediate soil thickness, and existing settlement. The settlement control measures of the existing station in the underpass construction of the new tunnel are divided into two categories. First, if the bearing capacity of the intermediate soil is insufficient, an external force must be applied to the existing structure to restore its original deformation position and compensate for the settlement deformation; compensatory jacking measures to compensate for the settlement of existing structures include jacking of jacks and grouts. Second, the limited bearing capacity of the intermediate soil must be improved through passive reinforcement measures to support the upper load. Passive reinforcement measures include freezing methods, pipe sheds (curtains), and grouting reinforcements. As shown in Figure 1, compared to the excavation span of the new tunnel, the thickness of the intermediate soil is more closely related to the settlement control measures of the existing station; the buried depth of the existing stations only had a slight effect. Thus, the correlation between the influencing factors and settlement control measures of the existing station was in the order of intermediate soil thickness > excavation span > station buried depth.
When the thickness of the intermediate soil is considerably low, tunnel excavation can easily lead to its destruction and is, thus, unable to support the existing structure effectively. Therefore, adopting compensatory jacking or relatively strong stratum reinforcement methods, such as freezing, is essential. When the thickness of the intermediate soil is less than 2 m, the jack lifting, grouting lifting, and freezing methods account for 40.42%, 12.76%, and 6.38%, respectively. When the thickness of the intermediate soil is more than 2 m, the reinforcement measures are primarily passive support measures, such as pipe roof (curtain) support and grouting reinforcement, and the proportion of compensation jacking control measures is 0. The excavation span of the tunnel also affects the selection of settlement control measures for existing stations. When the excavation span of the tunnel is large, the intermediate soil is relatively thin and long, which makes its destruction easy. Hence, strong reinforcement measures such as compensatory jacking are required. When the tunnel excavation span is greater than 20 m, the jack and grouting lifting measures account for 28.95% and 5.26%, respectively.
The study also analyzed the settlement of existing stations with different reinforcement measures, as shown in Figure 2.   The settlement of existing stations is influenced by several factors, such as the buried depth of the station, reinforcement measures, thickness of the intermediate soil, excavation span, and stratum conditions. This leads to a large dispersion in the settlement of existing stations, as shown in Figure 2. When the intermediate soil is thinner, the buried depth of the existing station, excavation span, and settlement of the existing station are larger. Figure 2 does not illustrate the law as a whole, indicating that settlement control measures play a key role. For projects with thin intermediate soils and large excavation spans, active control measures are often adopted to effectively suppress the settlement of existing structures.

Settlement Characteristics of Existing Stations
The settlement control measures of existing stations in the underpass construction include two categories: compensation jacking and passive reinforcement. Different settlement control measures lead to different settlement laws for the existing structures.
(1) Settlement of existing stations under the action of jack and grouting jacking The compensation jacking method primarily includes jack and grouting jacking. Both directly apply a jacking force to the existing structure through different media to ensure its settlement. Owing to the weak bearing capacity of the lower soil and insufficient support for the existing structure, the surface and existing structure have a large settlement. The settlement compensation of the existing structure is realized by actively applying jacking force, thus restoring the structural deformation and reducing large-scale settlement.
Zhang [38] provided the settlement law of an existing station in the construction of a tunnel between the Chaoyangmen and Dongdaqiao Stations of Beijing Metro Line 6 under the existing Chaoyangmen Station of Line 2 ( Figure 3). A tunnel was constructed using the CRD method, and the excavation span was 22.7 m. The stratum consisted of round pebbles and silty clay. The existing station has a three-span, rectangular frame structure. Jacks were used to lift the existing station to control its settlement.  As shown in Figure 3, the existing station has a large settlement in tunnel excavation owing to excavation unloading. In the later stage of the excavation, a jack was used to lift the existing structure and control its settlement, and the deformation of the existing station was restored to its initial position. The jack-lifting force plays an important role in lifting existing stations, and the magnitude of the lifting force directly affects the settlement deformation of the existing structures. When the lifting force was high, the lifting effect of the existing station was more significant. However, when the jacking force was excessively high, it easily caused an uplift of the existing station floor and affected normal operation. Therefore, controlling the size of the jacking force is the crucial in the lifting of the existing station.
Zhang [39] provided the settlement law of the existing station in the project of the Pingguoyuan Station of Beijing Metro Line 6, underpassing the Pingguoyuan Station of the existing Metro Line 1 at zero distance ( Figure 4). A tunnel was constructed using the pile-beam-arch method. The excavation span was 23.5 m, and the stratum was a sandy pebble. The existing station is a two-story, three-span box-frame structure. Grouting jacking was used to lift the existing station and control its settlement.  Similar to the jack-lifting law, grouting lifting causes an uplift in the existing structure. This ensures that the settlement deformation of the existing station is within the control standard. When the grouting pressure was higher, the lifting effect of the existing station was more evident. When the grouting pressure was excessively high, the existing structure was also uplifted.
Compensation lifting measures provide the existing structure with a compensation deformation, and the size of the compensation deformation depends on the jacking load. A reasonable jacking load setting is the key to compensating for jacking. Excessive jacking loads can cause structural damages. The jack jacking load is a concentrated load which can easily lead to an excessive load on the structure, whereas the grouting jacking load is close to a uniform load, which causes less damage to the existing structure.
(2) Settlement of the existing station under the passive reinforcement of intermediate soil The passive reinforcement of intermediate soil controls the existing settlement by strengthening the soil and improving its bearing capacity; this mainly includes grouting reinforcement, the freezing method, and pipe shed support. Although the freezing method has a strong reinforcement effect, it is limited to the stratum, and the number of applications is less than that of grouting reinforcement and pipe roof support.
Zhang [40] presented the settlement law for existing stations in the construction of the Chongwenmen underground excavation station of Beijing Metro Line 5 under an existing subway tunnel ( Figure 5). The tunnel was constructed using the column hole method. The excavation span was 24.2 m, and the stratum was silt. A pipe roof was used to support the existing station and control its settlement.  Figure 6 shows the settlement of an existing structure with a pipe roof support. Owing to the different stiffnesses of the pipe roof and soil, the soil displacement was uneven after the construction of pipe roof, and the stress was redistributed. The soil in the excavation area converts the upper load into compressive stress, which is transferred to the feet of the arch on both sides to form a micro-soil arch. This improves the bearing capacity of the soil between the pipes. Simultaneously, the pipe roof has a certain stiffness that protects the vault from collapsing and plays an important role in carrying the upper load. The soil and pipe roof constituted a vast bearing body that shared the upper load and reduced the settlement of the existing station. Compared with compensation jacking, passive reinforcement measures of the intermediate soil fully mobilize its bearing capacity, which has a certain economy. Meanwhile, the settlement of the existing station did not exhibit a reverse deformation, and the structural damage was smaller. (image by Wang [41]). Blue indicates that the plastic zone is not damaged. Green represents the range of plastic zone damage. Red represents the most severe damage to the plastic zone.
Compensated jacking actively compensates for the settlement deformation of existing structures by applying a jacking force. In contrast, the passive reinforcement of intermediate soil improves its bearing capacity and reduces the settlement of existing structures. Thus, the state of the intermediate soil has a significant relationship with the settlement control of existing stations. In particular, settlement control measures should be selected according to the intermediate soil state.

Computation Module
The stress state of the intermediate soil significantly affects the settlement of the existing structure. Therefore, a finite element model of the new tunnel beneath the existing station was established to analyze the relationship between the stress state of the intermediate soil and the settlement of the existing station. The minimum width of an ordinary subway station is 8 m, while the dimensions of the model were 90 m × 60 m. The section size of the existing station was 15 m × 10 m, the section size of the new tunnel was 9 m × 7 m, the initial support thickness was 0.35 m, the roof thickness was 1.1 m, the side wall thickness was 1.0 m, the floor thickness was 1.0 m, and the concrete strength was C30. The calculation model is illustrated in Figure 7. The formation and station parameters are detailed in Tables 1 and 2

Influence of Intermediate Soil Thickness on the Settlement of Existing Stations
The As shown in Figure 8a, when the thickness of the intermediate soil was larger, the settlement of the existing station was smaller. When the thickness of the intermediate soil was 15 m, the maximum settlement at the existing station was 0.2 mm. When the thickness of the intermediate soil was 1 m, the maximum settlement at the existing station was 9.8 mm. In addition, when the intermediate soil was thinner, the supporting effect of the soil on the upper structure was weaker; thus, the destruction of the soil under excavation unloading became easy. As shown in Figure 8b, as the intermediate soil became thinner, the settlement of the existing station structure accelerated. This indicated that the intermediate soil was destroyed as it became thinner, and the settlement of the existing structure increased rapidly. Figure 9 shows the plastic distribution of the intermediate soil for different intermediate soil thicknesses. As shown in Figure 9, when the thickness of the intermediate soil was less than 2 m, the plastic zone was mainly distributed on both sides of the excavation area of the new station and within the scope of the intermediate soil. At this time, the plastic zone penetrates the intermediate soil, which is completely destroyed. When the thickness of the intermediate soil was more than 2 m, the intermediate soil was destroyed above the new tunnel. However, the plastic zone did not completely penetrate the intermediate soil, which was partially destroyed. When the intermediate soil was completely destroyed, the bearing capacity was lost, and no supporting effect was present on the existing station. The settlement of existing stations was evidently increased. When the intermediate soil is not completely destroyed, it can provide support to the existing stations. The calculation shows that the critical thickness of the intermediate soil damage was approximately 2-4 m, which was also the critical point for an evident increase in the settlement of the existing station ( Figure 8b). An existing station cannot be supported when the intermediate soil is completely destroyed. Therefore, compensation jacking measures should be implemented to reduce settlement of existing stations. When the intermediate soil is not destroyed completely, using the intermediate soil for bearings is economical, which can be reinforced to improve its bearing capacity.

Influence of Mechanical Parameters of Intermediate Soil on the Settlement of Existing Stations
The intermediate soil can be easily destroyed when its mechanical properties are weak, which lowers its bearing capacity. Hence, the effects of the elastic modulus, internal friction angle, and cohesion of the intermediate soil are discussed. As shown in Figure 10, when the elastic modulus was 80 MPa, the maximum settlement of the existing station was 5.1 mm. In contrast, when the elastic modulus was 160 MPa, the maximum settlement of the existing station was 1.8 mm. The elastic modulus of the soil has an evident influence on the settlement deformation of the existing stations. When the elastic modulus is larger, the mechanical properties of the soil are improved. Consequently, the capacity of the soil to bear the upper load is improved, and the settlement of the existing stations becomes smaller. As shown in Figure 11, as the elastic modulus of the soil layer increased, the failure range of the plastic zone of the intermediate soil gradually decreased. Thus, a greater elastic modulus of the soil denotes a stronger stability, gradually enhancing its bearing capacity. Under the same load, the degree of soil damage was small, and the settlement deformation of the existing station was gradually reduced. As shown in Figure 12, the effect of varying cohesion on the settlement of existing stations was not evident. When the soil cohesion was 30 kN/m 2 , the maximum settlement at the existing station was 6.25 mm. When the soil cohesion was 90 kN/m 2 , the maximum settlement at the existing station was 6.9 mm. With an increase in soil cohesion, the settlement deformation of the existing station gradually decreased, but the change in cohesion had only a slight effect on the station settlement. As shown in Figure 13, with an increase in soil cohesion, the failure range of the soil plastic zone gradually decreased. With an increase in soil cohesion under the influence of the same stress, the ability to resist deformation increased, the degree of soil damage decreased, and the settlement of existing stations decreased. As shown in Figure 14, when the friction angle was 30°, the maximum settlement at the existing station was 6.5 mm. When the friction angle was 22°, the maximum settlement of the existing station was 10 mm. The soil friction angle exhibits a good linear relationship with the settlement of the existing station. With an increase in the friction angle, the failure range of the contact force chain between the soil particles decreases, and the settlement deformation of the existing station gradually decreases. The overall effect of the soil parameters on the settlement of the existing stations was not as sensitive as that of the thickness. When the intermediate soil is completely destroyed, the effect of controlling settlement is not significant even when the intermediate soil is reinforced.

Influence of Excavation Span of the Underground Tunnel on the Settlement of Existing Station
The effects of different excavation spans on the settlement of existing stations are also different, which affects the settlement deformation of the existing structures. To examine the influence of different excavation spans on the settlement of existing stations, finite element models with excavation spans of 5, 6, 7, 8, 9, 10, and 11 m were established, and the settlement deformation maps of existing stations at different excavation spans were extracted for comparative analysis (Figure 16). As shown in Figure 16, when the excavation span was 5 m, the maximum settlement at the existing station was 4.05 mm. When the excavation span was 11 m, the maximum settlement at the existing station was 8.26 mm. With an increase in the excavation span, the settlement of the existing station gradually increased, and the increasing trend is accelerated.
To determine the effect of different excavation spans on the settlement of the existing stations, a cloud diagram of the plastic zone of the intermediate soil was extracted, as shown in Figure 17. As shown in Figure 17, when the excavation span was 5 m, the plastic zone of the intermediate soil was mainly concentrated above the excavation area and had not yet penetrated the entire intermediate soil. Meanwhile, the intermediate soil was partially damaged and had a partial bearing capacity that could be controlled by passive reinforcement of the intermediate soil. When the excavation span was 11 m, the plastic zone penetrated the intermediate soil layer; the intermediate soil was completely damaged and lost all its bearing capacity. Therefore, the compensation jacking method must be used to control the settlement of existing stations. A larger excavation span results in a larger slenderness ratio of the intermediate soil, which is then easier to destroy. This causes a large settlement of the existing structure.

Influence of Buried Depth of Station on Settlement of Existing Station
To further explore the factors influencing the settlement of the existing station, finite element models of the station buried at depths of 10, 12, 14, 16, 18, and 20 m were established, and the settlement deformation maps of the existing station under different buried depths were extracted ( Figure 18). As shown in Figure 18, the buried depth of the station significantly affected the settlement deformation of the existing structure. A good linear relationship existed between the buried depth of the station and the settlement of the existing structure. When the buried depth of the existing station was 10 m, the maximum settlement of the existing station was 6.7 mm. When the buried depth of the existing station was 20 m, the maximum settlement of the existing station was 7.6 mm. Under the condition of same thickness of the intermediate soil, the relationship between the buried depth and the settlement of different existing stations is consistent. As the buried depth of the existing station increased, the settlement deformation of the existing station gradually increased.
To determine the influence of the buried depth of different stations on the settlement of existing stations, a cloud map of the plastic zone of the intermediate soil was extracted ( Figure 19). As shown in Figure 19, when the buried depth of the existing station was 10 m, the plastic zone of the intermediate soil was not penetrated; it still had a partial bearing capacity and presented a partial failure state. However, when the buried depth was 25 m, the plastic zone of the intermediate soil was severely damaged, the bearing capacity was considerably low, and the intermediate soil was in a completely failed state. With an increase in the buried depth of the existing station, the load on the station and intermediate soil is larger, and the damaged area of the intermediate soil is larger, resulting in a larger settlement of the existing station. According to the change in the plastic zone of the intermediate soil at different buried depths, the buried depth of the existing station affected the development of the plastic zone of the intermediate soil during excavation. In particular, a larger buried depth led to more evident damage to the intermediate soil. However, because an existing station can bear an upper load, the buried depth is not sensitive to damage in the intermediate soil.

Relationship between Failure Mode of the Intermediate Soil and the Reinforcement Method
Numerical simulations showed that the failure mode of the intermediate soil can be divided into complete and partial failures. After the intermediate soil was completely destroyed, the bearing capacity of the existing structure was lost, and the settlement of the existing structure increased. When the intermediate soil was completely destroyed, the intermediate soil was unable to bear the upper load even after it was reinforced. Therefore, the settlement control of existing stations should adopt a method of compensation jacking. Passive soil reinforcement measures should be adopted when intermediate soil is partially destroyed. By reinforcing the intermediate soil, the bearing capacity is improved, and the settlement of the existing structure is reduced. Therefore, the determination of the stress state of the intermediate soil is crucial for the formulation of settlement measures for existing stations.
In practical engineering applications, the geological conditions of various projects vary. Determining whether the intermediate soil is damaged on the basis of the thickness of the intermediate soil, buried depth of the existing station, excavation span, and mechanical parameters of the soil may be inaccurate. Hence, a mechanical model of the intermediate soil was established, which was related to the strength index of the intermediate soil, to determine the failure mode of the intermediate soil, and the corresponding reinforcement control measures can be considered.

Intermediate Soil Mechanics Model
After the excavation of the new station, although the lining project has not yet been conducted, the simplified method can be used to calculate the situation of the intermediate soil. This method simplifies the intermediate soil into an upper beam that is affected only by the gravity and formation pressure of the existing station, and the soil around the lower excavation area provides vertical support. Simultaneously, the self-weight of the intermediate soil can be simplified into a uniform load acting on the beam according to the conversion method of the constant body and surface forces in elastic mechanics [43][44][45]. Finally, a mechanical model of the intermediate soil is obtained (Figure 20) [46]. (1) After solving Equation (1), the full solution of the equilibrium differential equation can be obtained as where Ф is Airy stress function. Considering a constant body force, Ф is used as the equation for an unknown function. Ф can be solved by the stress function method, and the compatibility equation expressed by stress function can be obtained as follows: According to the theory of material mechanics, the stress components σx, σy, and τxy are mainly caused by bending moment, shear force, and load F, respectively. According to the intermediate soil mechanics model σy is a function of y.
( ) (4) Substituting Equation (4) into Equation (2) gives The stress function form is obtained by integrating x as By substituting Equation (6) Equation (7) is a quadratic equation of x, and the stress function must satisfy the compatibility equation; therefore, the coefficient and free term of Equation (7) are zero. That is, The expressions for f(y), f1(y), and f2(y) can be obtained by solving for the three equalities in Equation (8).
By substituting Equation (9) into Equation (6), the expression for the stress function can be obtained as Substituting Equation (10) into Equation (2), the expression for each stress component is obtained as follows: According to the boundary conditions of the intermediate soil mechanics model and the principle of the Saint-Venant local effect, the following can be observed: According to the aforementioned conditions, the expression for the final stress component is obtained as follows:

Intermediate Soil Failure Criterion
The intermediate soil is dominated by shear failure when the strength fails, and the strength of the intermediate soil can be analyzed using the third strength theory [38]. In this theory, the maximum shear stress is assumed to be the factor that causes the yield failure of geotechnical materials. Regardless of the stress state, the material will yield as long as the maximum shear stress at a point in the component reaches the limit value of the material yield. The corresponding equation is as follows: If the maximum shear stress calculated by Equation (14) where c is cohesion, q is the overload on both sides, q d γ = (where γ is the weight of intermediate soil and d is its thickness), and b is the width of intermediate soil. Nc, Nq, and Nγ are bearing coefficients, which can be obtained according to the friction angle (Table 3).

Engineering Case Analysis
The Combined with practical cases, the comparative relationship between the shear stress and ultimate bearing capacity of intermediate soil with the influence of different intermediate soil thicknesses, excavation spans, and buried depths of existing stations was analyzed ( Figure 21). When the thickness of the intermediate soil was less than 2 m, compensation jacking measures were required to reduce the settlement of the existing structure. When the thickness of the intermediate soil exceeded 2 m, the settlement of the station was controlled by reinforcing the soil. At the construction site, the grouting jacking method was used to control the settlement of existing stations, and good results were achieved.

Conclusions
Intermediate soil has a significant influence on the settlement of the existing station as a connector between the new tunnel and the existing station. Data Availability Statement: Not applicable.

Conflicts of Interest:
The authors declare no conflict of interest.
Appendix A Residual cohesive soil, granite fully strong weathered layer and medium weathered, slightly weathered zone Grouting reinforcement Step method initial support + shield segment 6.1 Chongqing Rail Line 10 Hongtudi Station of Rail Line 6 5.06 11.54 Sandy mudstone, sandstone, sandy mudstone strata Grouting reinforcement CRD method 8.42