Spray-Pyrolytic Tunable Structures of Mn Oxides-Based Composites for Electrocatalytic Activity Improvement in Oxygen Reduction

: Hybrid nanomaterials based on manganese, cobalt, and lanthanum oxides of different morphology and phase compositions were prepared using a facile single-step ultrasonic spray pyrolysis (USP) process and tested as electrocatalysts for oxygen reduction reaction (ORR). The structural and morphological characterizations were completed by XRD and SEM-EDS. Electrochemical performance was characterized by cyclic voltammetry and linear sweep voltammetry in a rotating disk electrode assembly. All synthesized materials were found electrocatalytically active for ORR in alkaline media. Two different manganese oxide states were incorporated into a Co 3 O 4 matrix, δ -MnO 2 at 500 and 600 ◦ C and manganese (II,III) oxide-Mn 3 O 4 at 800 ◦ C. The difference in crystalline structure revealed ﬂower-like nanosheets for birnessite-MnO 2 and well-deﬁned spherical nanoparticles for material based on Mn 3 O 4 . Electrochemical responses indicate that the ORR mechanism follows a preceding step of MnO 2 reduction to MnOOH. The calculated number of electrons exchanged for the hybrid materials demonstrate a four-electron oxygen reduction pathway and high electrocatalytic activity towards ORR. The comparison of molar catalytic activities points out the importance of the composition and that the synergy of Co and Mn is superior to Co 3 O 4 /La 2 O 3 and pristine Mn oxide. The results reveal that synthesized hybrid materials are promising electrocatalysts for ORR. The also by the state of Mn oxide. SEM images reveal ﬂower-like nanosheets for hybrid materials with birnessite-MnO 2 and well-deﬁned spherical nanoparticles for material based on Mn 3 O 4 and for the material based only on Co as catalysts (Co 3 O 4 /La 2 O 3 ). The electrochemical performance of MnO x /Co 3 O 4 and Co 3 O 4 /La 2 O 3 demonstrate a comparable ORR activity to Pt/C and superior activity to the pristine Mn oxide electrodes. It was shown that the mass activity of synthesized hybrid materials not supported on carbon blacks outperforms the literature values of carbon-based materials. Mass activity performance was compared to the molar activity—calculated per mol of the Mn and Co oxides being in charge for the catalytic performance in oxygen reduction reaction. It was revealed that the synergic coupling of Mn oxides and Co 3 O 4 have better catalytic performance in comparison to the electrodes based on pristine MnO 2 and Co 3 O 4 /La 2 O 3 . It was found that molar and mass activities give different information, since different amounts of active components are affecting the synergistic catalysis.


Introduction
Economic development and extensive use of fossil fuels has led to fast depletion of energy resources. Hence, the development of clean energy storage and conversion devices, such as metal-air batteries, supercapacitors, fuel cells, and other renewable energy technologies, is in the main focus of numerous researchers and laboratories worldwide [1,2]. The efficiency of these energy devices mainly depends on the electrochemical oxygen reduction reaction (ORR) that occurs at the cathode side, as limiting reaction [3]. High activation barriers, poor rate capability, sluggish kinetics, and serious voltage gap of oxygen electrode reactions limit the performance of energy devices that rely on ORR [4][5][6].
Until now, the most investigated ORR catalysts have been based on noble metals such as Pt and Pt alloys, to achieve favorable reaction rates [7]. However, the high price and scarcity of the precious metals, inferior stability and sensitivity to CO poisoning, severely limit their widespread applications [2,3,8]. To overcome the above-mentioned to combine it with other oxides and carbon materials [38][39][40]. Due to its high potential as a stabilizing agent and high activity when mixed with other oxides, in this work it was utilized in the synthesis with Mn-and Co-oxide.
It was shown that combination of oxides, especially TMOs, and their structures, like spinel and perovskite-type oxides, could exhibit excellent ORR activities owing to the combination of metal elements, compared to single-metal oxides [7,41,42]. For example, Co-oxide nanoparticles modified with Mn-oxide nanotube have served as oxygen cathode catalyst for rechargeable zinc-air batteries [43]. La-, Co-, Mn-oxide prepared with carbon nanotubes (CNT) as composite has been successfully used as a bi-functional air electrode in Zn-air batteries [37]. The improved synergy effect has been reported in comparing to single oxide utilization. For example, various structures like honeycomb double-layer MnO 2 /Cobalt doped for primary zinc-air batteries [44], 3D hollow sphere Co 3 O 4 /MnO 2 -CNT [45], and core-shell Co 3 O 4 @MnO 2 [46] have been evaluated as bifunctional catalysts materials and applied for batteries and supercapacitors.
Therefore, we aimed to synthesize and investigate hybrid nanomaterials based on the Mn/Co/La oxides of ordered structure generated by ultrasonic spray pyrolysis (USP) as electrocatalyst for ORR. USP technique was chosen for the synthesis of these materials as it allows a simple single step approach of synthesizing nanomaterials with precisely controllable morphologies and chemical compositions. Different compositions and morphologies were synthesized depending on USP temperature and tested.
One of the issues to be considered is that the future ORR materials should not contain rather electrochemically unstable carbonaceous materials as support. The investigated MnO x -Co 3 O 4 TMO hybrid electrode nanomaterials were carbon free. The influence of manganese oxide type on the ORR as well as difference in composition of Mn and Co was evaluated. The second important issue that we tackled is that the materials should be synthesized using a low-cost, simple technique that can be easily applied also for the large scales such as USP.

Material Synthesis
The synthesis of Co/Mn/La oxide hybrid materials was performed by single-step ultrasonic spray pyrolysis process. The solution for the material synthesis was prepared by mixing starting precursor solutions to give desired stoichiometric mole ratios La:Co:Mn = 3:5:10. The ratio of La:Co:Mn of 3:5:10 was chosen based on previous research [47,48], since we wanted to investigate the influence of Mn in mixture for ORR reaction. Aqueous 0.1 M solutions of La(NO 3 ) 3 , Mn(NO 3 ) 2 and CoCl 2 were used as precursors. The USP conversion temperature was adjusted and controlled using a thermostated furnace. All powders were synthesized by ultrasonic spray pyrolysis in the equipment with horizontal nebula flow.
Nebula generation from the prepared solutions of precursors took place in an ultrasonic atomizer (Gapusol 9001, RBI/France) with an ultrasonic nebulizer (Prizma Kragujevac, Serbia) to create an nebula-born aerosol [47,48]. The nebula with droplets having a diameter of around 2.3 µm was produced with an ultrasound frequency of 2.5 MHz. The nebulization/aerosol generation was carried out in O 2 /N 2 atmosphere as carrier gas, having O 2 to N 2 in volume ratio of 2:1 and continuous flow rate of 3 dm 3 min -1 . The synthesis temperatures were set to 500, 600, or 800 • C.

Electrode Preparation
For the electrochemical measurements, the catalyst-modified surface of electrodes was prepared from the glassy carbon disc (Pine Research Instrumentation USA, 5 mm). Prior to the use, glassy carbon disc was polished with alumina slurry kit (Pine Research Instrumentation, Durham, NC, USA) of different grades, and then cleaned ultrasonically in ethanol and water.
The electrodes were prepared in the following way. Firstly, 5 mg mL −1 of water suspension of the USP-synthesized powder was agitated in an ultrasonic bath for 30 min in order to form homogeneous ink. Then, 20 µL of the ink were cast by micropipette onto the glassy carbon disc and left to air-dry for 2 h. In the next step, 10 µL of Nafion solution (100:1 diluted commercial Nafion solution) were pipetted onto the catalyst-covered GC disc, as binding agent, and left to dry at room temperature.

Material Characterization
Structural and phase analysis of the synthesized materials was investigated by X-ray diffraction (XRD). The measurements were undertaken on a Philips PW 1050 powder diffractometer with Ni-filtered CuKα radiation at room temperature and scintillation detector within the range 10-82 • in steps of 0.05 • with the scanning rate of 5 s/step.
Scanning electron microscopy (SEM) with an energy dispersive X-ray spectroscopy (EDS) were employed to analyze morphology and element composition of porous Mn/Co/La oxide hybrid materials. Scanning electron microscope (Zeiss DSM 982 Gemini; Vega TS 5139MM Tescan, Brno, Czech Republic) was employed for the examination of obtained particles on a different magnification level providing different information on the morphology and particle shape and size. The elemental composition was determined by EDS with Si(Bi) X-ray detector connected to SEM and a multi-channel analyzer.

Electrochemical Measurements
Electrochemical measurements were performed using BioLogic potentiostat (BioLogic SAS, SP-240, Grenoble, France). The electrocatalytic properties of the hybrid materials were checked by means of cyclic voltammetry (CV) and linear sweep voltammetry (LSV), using the scan rate of 50 and 2 mV s −1 , respectively. In order to check the material activity for oxygen reduction reaction, 3-electrode set-up, using a rotating disk working electrode was employed. The GC modified with synthesized materials as described in Section 2.2.2 were used as working electrode, while saturated calomel (SCE) and Pt electrode were employed as the reference and counter electrode, respectively. All the potentials presented are referred to the SCE. The supporting electrolyte was a 0.1 M aqueous KOH solution. All electrochemical experiments were performed at 25 • C under nitrogen or oxygen atmosphere at 600, 800, 1000, 1500, or 2500 rpm rotation of the working electrode. Prior to every experiment, either in N 2 or O 2 atmosphere, the gas was bubbled through the electrolyte for at least 20 min.

XRD Analysis
The hybrid nanomaterials based on rare earth/transition metal oxides were synthesized with facile and cost-effective USP procedure, bearing in mind the methodology as follows. One group of electrocatalyst is based on manganese, cobalt, and lanthanum metals and the effects of three different USP temperatures were investigated (500, 600, and 800 • C). The other group of materials was prepared by the same synthesis procedure, but without manganese component-it was only based on cobalt and lanthanum oxide, in order to investigate the influence of USP-synthesized Mn oxide within hybrid oxide electrocatalysts. For the sake of comparison, the electrocatalytical performance of commercial manganese oxide was also included in the investigations.
The crystalline structures of the hybrid materials were revealed by XRD analysis. X-ray diffraction patterns of synthesized materials are presented in Figure 1. As can be seen in Figure 1a, the materials synthesized at 500 and 600 • C are composed mainly of manganese (IV) oxide in the form of birnessite, also denoted as δ-MnO 2 , as defined by main diffraction peaks at 2θ of 12.4, 25.3, 37, and 66 • . The specific XRD peaks correspond to a card no.: JCPDS 00-043-1456 (MnO 2 ). Birnessite is reported as 2D layered manganese oxide with lamellar structure consisting of edge-sharing MnO 6 octahedra, and is considered to be the most active phase for ORR among other crystalline structures of MnO 2 [49][50][51]. In addition, the diffraction peaks at 18.9, 31.2, 45, and 59 • reveal the presence of Co 3 O 4 (JCPDS card no. 01-080-1535). However, La oxide or other compounds which should indicate the La presence are not evidenced. It follows that La is present as poorly crystalline or amorphous lanthanum compound(s). These "La-hided" states of Co-La oxide hybrids corresponds to our recent findings [48].

SEM and EDS Characterization
The morphology of as-synthesized catalytic materials was investigated by SEM. Depending on the preparation temperature the samples morphology appears different, as shown in Figure 2. For the materials prepared at the temperatures 500 and 600 °C, the results indicate formation of spherical grains, Figure 2a,c, with a petal-like structure discovered at the higher-resolution images (Figure 2b,d). It can be seen that the petal-structured grains, having the size of around 2 µm, are built from numerous nanosheets. The nanosheets appear finer and more densely packed at higher USP tem- (JCPDS card no. 03-06502776). Additionally, the diffraction peaks related to the JCPDS card no. 01-075-0440 confirms the formation of the perovskite structure-LaMnO 3 . It can be seen that XRD peaks in Mn-containing compounds synthesized at 800 • C are sharper than those at lower temperatures, which indicate highly crystalline nature of those compounds. The formation of different manganese oxide types at different temperatures is expected. It has been already reported that under these conditions Mn changes its form from Mn(IV) oxide to Mn(II, III) oxide [52]. Synthesized hybrid materials are denoted as MnO 2 /Co 3 O 4 -500, MnO 2 /Co 3 O 4 -600, and Mn 3 O 4 /Co 3 O 4 -800 in the further text, according to XRD findings.
The structural and phase characteristics of the Mn-free synthesized material, based on cobalt and lanthanum compounds, is presented in Figure 1c. XRD peaks clearly confirm formation of Co 3 O 4 . In addition, weak peaks at positions 26.2 • , 29.8 • , and 78 • indicate the formation of La 2 O 3 , although it can be assumed that this oxide is present mainly in an amorphous form. Thus, this catalytic material is denoted as Co 3 O 4 /La 2 O 3 in further text.

SEM and EDS Characterization
The morphology of as-synthesized catalytic materials was investigated by SEM. Depending on the preparation temperature the samples morphology appears different, as shown in Figure 2. For the materials prepared at the temperatures 500 and 600 • C, the results indicate formation of spherical grains, Figure 2a,c, with a petal-like structure discovered at the higher-resolution images (Figure 2b,d). It can be seen that the petal-structured grains, having the size of around 2 µm, are built from numerous nanosheets. The nanosheets appear finer and more densely packed at higher USP temperature (Figure 2b,d). The very similar structures were observed by Che et al. reporting the core-shell microspheres composed of Co 3 O 4 @MnO 2 with flower-like structured Co 3 O 4 as the core onto which MnO 2 nanosheets have been subsequently grown [46]. This typical flower-like morphology of birnessite-MnO 2 forming micro/nanospheres has been also reported to have high surface area that might exhibit fast electrode kinetics and good stability. MnO 2 nanosheets are thus recognized as excellent candidates for electrocatalytic materials for electrochemical oxygen reactions [50,51,53].
On the other hand, the Mn 3 O 4 /Co 3 O 4 material synthesized at 800 • C has homogenous dense structure as presented in Figure 3. The enlarged SEM image reveals well-defined submicron particles of the catalytic material ( Figure 3b). Similar change in morphology, leading to the formation of defined particles instead of flower-like structure, has been reported and assigned to the presence of Mn 3 O 4 type of Mn oxide, in comparison to the distinguished nanosheets typical for MnO 2 [54,55]. The SEM images of Co 3 O 4 /La 2 O 3 catalytic material shows highly agglomerated particles with irregular shapes and various sizes ranging from nano-to several µm ( Figure 3d). The porous agglomerated particles of Co 3 O 4 material have also been reported, providing large micro-and mesoporous surface [56].
The elemental composition, done by energy dispersive X-ray spectroscopy (EDS), confirms the presence of Mn, Co, La, and O with the atomic ratios presented in Table 1. It can be seen that for MnO 2 /Co 3 O 4 -500, MnO 2 /Co 3 O 4 -600, and Mn 3 O 4 /Co 3 O 4 -800 materials, the obtained atomic ratio of Mn:Co is close to 2:1, which is in accordance to the projected atomic ratio used for synthesis. On the other hand, the atomic ratio between lanthanum, cobalt, and manganese is smaller than projected ratio. This anticipates that the material is likely structured as separated phases of the oxides of well-resolved crystalline state, MnO 2 and Co 3 O 4 , covering poorly crystalized La compounds, as found by XRD, which can mask its EDS response. Finally, it was seen in XRD patterns that Co 3 O 4 /La 2 O 3 catalytic material exhibits diffraction peaks similar to La 2 O 3 card, which can cause the apparently hidden XRD state of La 2 O 3 by crystalline Co 3 O 4 .

Electrochemical Characterization
To study the electrocatalytic performances of synthesized Mn/Co/La-hybrid materials for oxygen reduction reaction, three-electrode half-cell design was used. Electrodes were prepared with catalytic material as described above in Section 2.2.2 and used as working electrodes in an RDE system to provide constant hydrodynamic conditions. On the other hand, the Mn3O4/Co3O4 material synthesized at 800 °C has homogeno dense structure as presented in Figure 3. The enlarged SEM image reveals well-defin sub-micron particles of the catalytic material (Figure 3b). Similar change in morpholo leading to the formation of defined particles instead of flower-like structure, has b reported and assigned to the presence of Mn3O4 type of Mn oxide, in comparison to distinguished nanosheets typical for MnO2 [54,55]. The SEM images of Co3O4/La2O3 c alytic material shows highly agglomerated particles with irregular shapes and vario sizes ranging from nano-to several µm (Figure 3d). The porous agglomerated particle Co3O4 material have also been reported, providing large micro-and mesoporous surf [56].
The elemental composition, done by energy dispersive X-ray spectroscopy (ED confirms the presence of Mn, Co, La, and O with the atomic ratios presented in Table 1 can be seen that for MnO2/Co3O4-500, MnO2/Co3O4-600, and Mn3O4/Co3O4-800 materi the obtained atomic ratio of Mn:Co is close to 2:1, which is in accordance to the projec atomic ratio used for synthesis. On the other hand, the atomic ratio between lanthanu cobalt, and manganese is smaller than projected ratio. This anticipates that the materia likely structured as separated phases of the oxides of well-resolved crystalline st MnO2 and Co3O4, covering poorly crystalized La compounds, as found by XRD, wh can mask its EDS response. Finally, it was seen in XRD patterns that Co3O4/La2O3 cataly  [44,51,57]. The redox processes appeared suppressed upon increase in synthesis temperature. On the other hand, CV behavior of Co 3 O 4 /La 2 O 3 hybrid material shows fully reversible redox transitions of much higher currents at the potentials positive to −0.1 V, which can be assigned to redox transitions of Co. This CV performance has been reported as typical behavior of cobalt oxide nanoparticles [58]. The shape of CV curves of Co 3 O 4 /La 2 O 3 is different in comparison to that of MnO 2 /Co 3 O 4 materials, with considerably higher capacitive currents. It seems that CV fingerprints follow the registered structural organization of the oxides in the Co 3 O 4 /La 2 O 3 material. Cobalt oxide particles dictate the CV behavior of Co 3 O 4 /La 2 O 3 material in a way to resemble completely the redox processes of pure Co 3 O 4 . On the other hand, Mn-based materials are of CV behavior similar to pristine MnO 2 , since the particle surface composition is of twice as much as nominal loading of manganese with respect to cobalt. CV response of MnO 2 /Co 3 O 4 synthesized at lower temperature (MnO 2 /Co 3 O 4 -500) strives for the shape more similar to that of Co 3 O 4 . This could be related to the more spaced petals (Figure 2b) with respect to dense appearance of petals at higher synthesis temperature (MnO 2 /Co 3 O 4 -600, Figure 2d). It follows that C O3 O 4 contributes more to CV response through the more spaced MnO 2 -rich petals (Table 1). Additionally, it seems that the absence of petal-like structure and transition from MnO 2 to Mn 2 O 3 (Figures 1b and 3d)

Electrochemical Characterization
To study the electrocatalytic performances of synthesized Mn/Co/La-hybrid m rials for oxygen reduction reaction, three-electrode half-cell design was used. Electro were prepared with catalytic material as described above in Section 2.2.2 and used working electrodes in an RDE system to provide constant hydrodynamic conditions.
Cyclic voltammograms were recorded in the potential window between −0.9 and  ( Figure 2b) with respect to dense appearance of petals at higher synthesis tempe (MnO2/Co3O4-600, Figure 2d). It follows that CO3O4 contributes more to CV re through the more spaced MnO2-rich petals (Table 1). Additionally, it seems that sence of petal-like structure and transition from MnO2 to Mn2O3 (Figures 1b and the case of Mn2O3/Co3O4-800 does not affect much the CV response of rather low-c featureless characteristics. (a) (b) The electrocatalytic activities of the prepared nanocatalysts for ORR were eva by means of LSV in O2-saturated alkaline electrolyte. Figure 5 presents ORR e chemical performances of Mn/Co/La oxides synthesized at three different temper As can be seen, when the electrolyte was saturated with O2, remarkable reductio rents are observed, which introduces the synthesized materials as ORR-active. Th potential of all electrodes was approx. −0.3 V vs. SCE, which is competitive to othe based materials [56]. The electrode material at 500° and 600° show similar curve and activity, which is expected for similar flower-like birnessite MnO2, having electrochemical activities between 1 and 2.5 mA cm −2 (Figure 5a) [51]. The Mn3O4 material, obtained at 800 °C, exhibits higher ORR activity than MnO2/Co3O4-5 MnO2/Co3O4-600 materials. This can be ascribed to the presence of Mn3O4 as cataly mixed oxidation state (+2, +3) in comparison to the MnO2 with +4 oxidation state The electrocatalytic activities of the prepared nanocatalysts for ORR were evaluated by means of LSV in O 2 -saturated alkaline electrolyte. Figure 5 presents ORR electrochemical performances of Mn/Co/La oxides synthesized at three different temperatures. As can be seen, when the electrolyte was saturated with O 2 , remarkable reduction currents are observed, which introduces the synthesized materials as ORR-active. The onset potential of all electrodes was approx. −0.3 V vs. SCE, which is competitive to other TMO based materials [56]. The electrode material at 500 • and 600 • show similar curve shape and activity, which is expected for similar flower-like birnessite MnO 2 , having similar electrochemical activities between 1 and 2.5 mA cm −2 (Figure 5a) [20]. Additionally, as it is registered by SEM, two different manganese types provide different morphologies. Consequently, the ORR current increases continuously for Mn3O4/Co3O4-800, whereas the reduction on MnO2/Co3O4-500 and -600 appears stepped, with a transition around −0.7 V. This could be the indication of different ORR mechanisms on MnO2/Co3O4 and Mn3O4/Co3O4. For the sake of comparison to pristine MnO2, electrode activities calculated per mass of MnO2 (mass activity) was performed, as presented in Figure 5b. It can be seen that nanostructured MnO2/Co3O4 materials are of significantly improved ORR activity compared to the pristine manganese oxide. This proves the validity of the hybrid oxides approach of ordered structure for the synthesis of materials for ORR. In order to study ORR activity further, the series of polarization curves (LSV) in saturated oxygen atmosphere were recorded at different electrode rotating rates between 600 and 2500 rpm. As can be seen in Figure 6a, ORR current is increasing with the increase of the rotation rate at higher overpotentials, due to the improved mass transfer. However, the first reduction step (positive to −0.7 V) for MnO2/Co3O4-500 and -600 appears negligibly dependent on rotation rate. It follows that corresponding process(es) are For the sake of comparison to pristine MnO 2 , electrode activities calculated per mass of MnO 2 (mass activity) was performed, as presented in Figure 5b. It can be seen that nanostructured MnO 2 /Co 3 O 4 materials are of significantly improved ORR activity compared to the pristine manganese oxide. This proves the validity of the hybrid oxides approach of ordered structure for the synthesis of materials for ORR.
In order to study ORR activity further, the series of polarization curves (LSV) in saturated oxygen atmosphere were recorded at different electrode rotating rates between 600 and 2500 rpm. As can be seen in Figure 6a, ORR current is increasing with the increase of the rotation rate at higher overpotentials, due to the improved mass transfer. However, the first reduction step (positive to −0.7 V) for MnO 2 /Co 3 O 4 -500 and -600 appears negligibly dependent on rotation rate. It follows that corresponding process(es) are not directly related to ORR, but to partial reduction of the material induced by the presence of oxygen (please see Equations (3)-(7)).
Mn 3+ , which is followed by adsorption and reduction of oxygen. Hence, the promotion of Mn 3+ generation could lead to more effective ORR over stronger oxygen adsorption and accelerated O2 reduction to OH − , which results in overall increase in catalytic activity [49]. Furthermore, it has been reported that porous structure can also stabilize Mn 3+ species at the particle surface [36]. For the synthesized materials, Figure 6b reveals that the number of transferred electrodes, calculated from the slope, for MnO2/Co3O4-500 and -600 catalytic materials are 3.6 and 3.89 which is close to 4 indicating that ORR catalyzed by those materials proceeds via quasi-four-electron ORR mechanism. However, the overall electron transfer number of Mn3O4/Co3O4-800 material is calculated to be 3, indicating that both of the suggested schemes coexist in the catalyzing process [60]. Even though the higher oxidation states of Mn (Mn 4+ and Mn 3+ ) are considered as crucial for manifestation of Mn cation defects and oxygen vacancies that are important as catalytically active sites, the morphology of samples at 500, 600, and 800, as well as their mutual interaction with Co-oxide, also plays an important role in catalytic activity. The Co3O4/La2O3 material was also checked for the ORR performance at various rotation speeds, as presented in Figure 7. The ORR on this hybrid material starts at approx. −0.35 V vs. SCE, which is in accordance to other Co3O4 reported nanomaterials, but still is considerably negative if compared to the commercial 20 wt.% Pt@XC-72 catalyst (−0.16 V) [56]. On the other hand, the current of approx. −3.3 mA cm −2 is higher in comparison to the performance of similar nanomaterials, found as −2.5 [56], −1.5 [43], and −1 mA cm −2 The number of the electrons that are involved in oxygen reduction reaction is an important parameter for evaluating the catalytic performance of the synthesized materials. Therefore, the ORR was further analyzed using Koutecky-Levitch (KL) equation (Equation (1)). The corresponding linear fit that is presented in Figure 6b at E = −1 V, was used to calculate the number of electrons transferred during the oxygen reduction with synthesized materials. In the equation: where j corresponds to the measured current density, n is the overall number of electrons exchanged, F stands for Faraday constant (F = 96486 C mol −1 ), C 0 is the oxygen concentration in 0.1 M KOH (typically C 0 = 1.2 × 10 −6 mol cm −3 ), D is oxygen diffusion coefficient (typically D = 1.9 × 10 −5 cm 2 s −1 ), υ is the kinematic viscosity of the solution (υ = 0.01 cm 2 s −1 ); surface area of the electrode used to calculate current density is A = 0.196 cm −2 .
It has been reported that the ORR in alkaline media can proceed either via two-electron pathway, which involves the formation of hydrogen peroxide as an intermediate, or via direct four-electron reduction pathway where oxygen is directly reduced to OH − [59]. Generally, direct four-electron transfer pathways are more desirable than the partial reduction pathway since it provides a higher rate for ORR. Although the ORR mechanism on Mn-oxide is still not fully understood, the possible pathway suggests the reactions described: The overall reaction of Equations (3), (4), and (6) equals to the four-electron reduction process, whereas the summary of Equations (3), (5), and (7) results in an overall two-electron transfer mechanism oxygen reduction. In the first step, Mn 4+ is reduced to Mn 3+ , which is followed by adsorption and reduction of oxygen. Hence, the promotion of Mn 3+ generation could lead to more effective ORR over stronger oxygen adsorption and accelerated O 2 reduction to OH − , which results in overall increase in catalytic activity [49]. Furthermore, it has been reported that porous structure can also stabilize Mn 3+ species at the particle surface [36]. For the synthesized materials, Figure 6b reveals that the number of transferred electrodes, calculated from the slope, for MnO 2 /Co 3 O 4 -500 and -600 catalytic materials are 3.6 and 3.89 which is close to 4 indicating that ORR catalyzed by those materials proceeds via quasi-four-electron ORR mechanism. However, the overall electron transfer number of Mn 3 O 4 /Co 3 O 4 -800 material is calculated to be 3, indicating that both of the suggested schemes coexist in the catalyzing process [60]. Even though the higher oxidation states of Mn (Mn 4+ and Mn 3+ ) are considered as crucial for manifestation of Mn cation defects and oxygen vacancies that are important as catalytically active sites, the morphology of samples at 500, 600, and 800, as well as their mutual interaction with Co-oxide, also plays an important role in catalytic activity.
The Co 3 O 4 /La 2 O 3 material was also checked for the ORR performance at various rotation speeds, as presented in Figure 7. The ORR on this hybrid material starts at approx. −0.35 V vs. SCE, which is in accordance to other Co 3 O 4 reported nanomaterials, but still is considerably negative if compared to the commercial 20 wt.% Pt@XC-72 catalyst (−0.16 V) [56]. On the other hand, the current of approx. −3.3 mA cm −2 is higher in comparison to the performance of similar nanomaterials, found as −2.5 [56], −1.5 [43], and −1 mA cm −2 [58] at similar electrode potentials. ORR on synthesized Co 3 O 4 /La 2 O 3 was studied also using a KL plot shown in Figure 7b. The number of electrons transferred, calculated based on KL equation, is 3.7 suggesting predominantly the pathway of direct four-electron reduction of oxygen. This is fairly comparable to the state-of-the-art electrode based on Pt (20% wt. Pt@XC-72), which is reported to be between 3.8 and 4.03 [56].
Metals 2022, 11, x FOR PEER REVIEW 12 of 17 [58] at similar electrode potentials. ORR on synthesized Co3O4/La2O3 was studied also using a KL plot shown in Figure 7b. The number of electrons transferred, calculated based on KL equation, is 3.7 suggesting predominantly the pathway of direct four-electron reduction of oxygen. This is fairly comparable to the state-of-the-art electrode based on Pt (20% wt. Pt@XC-72), which is reported to be between 3.8 and 4.03 [56]. Finally, the comparison of all synthesized oxide combinations as catalytic materials is presented in Figure 8. As can be seen, Co3O4/La2O3 catalyst outperforms MnO2/Co3O4 and Mn3O4/Co3O4 materials, in comparison to the onset electrode potential, as well as in electrocatalytic activity toward ORR in the studied potential region. Similar behavior has been reported by Xu et al. showing that Co3O4/La2O3 supported by carbon nanotubes (CNT) has shown better activity in comparison to the MnO2/Co3O4-CNT. Although CNT have been used to increase catalytically active surface area, the activities of the studied Finally, the comparison of all synthesized oxide combinations as catalytic materials is presented in Figure 8. As can be seen, Co 3 O 4 /La 2 O 3 catalyst outperforms MnO 2 /Co 3 O 4 and Mn 3 O 4 /Co 3 O 4 materials, in comparison to the onset electrode potential, as well as in electrocatalytic activity toward ORR in the studied potential region. Similar behavior has been reported by Xu et al. showing that Co 3 O 4 /La 2 O 3 supported by carbon nanotubes (CNT) has shown better activity in comparison to the MnO 2 /Co 3 O 4 -CNT. Although CNT have been used to increase catalytically active surface area, the activities of the studied hybrid materials are in the range 1.8-4 mA cm −2 that is comparable to our hybrid materials but without addition of a carbon support [37].
Finally, the comparison of all synthesized oxide combinations as catalytic materials is presented in Figure 8. As can be seen, Co3O4/La2O3 catalyst outperforms MnO2/Co3O4 and Mn3O4/Co3O4 materials, in comparison to the onset electrode potential, as well as in electrocatalytic activity toward ORR in the studied potential region. Similar behavior has been reported by Xu et al. showing that Co3O4/La2O3 supported by carbon nanotubes (CNT) has shown better activity in comparison to the MnO2/Co3O4-CNT. Although CNT have been used to increase catalytically active surface area, the activities of the studied hybrid materials are in the range 1.8-4 mA cm −2 that is comparable to our hybrid materials but without addition of a carbon support [37].
(a) (b) Figure 8. Comparison of (a) synthesized materials in mA (b) calculated per mass of Co.
As mentioned above, the mechanism on the synthesized electrode most probably proceeds with an additional MnOOH reaction step. It has been reported that this reaction is unfavorable due to the strength of the Mn-O bond which makes the initial reduction more difficult. This leads to lower electrocatalytic activity of the electrodes with high Figure 8. Comparison of (a) synthesized materials in mA (b) calculated per mass of Co.
As mentioned above, the mechanism on the synthesized electrode most probably proceeds with an additional MnOOH reaction step. It has been reported that this reaction is unfavorable due to the strength of the Mn-O bond which makes the initial reduction more difficult. This leads to lower electrocatalytic activity of the electrodes with high percentage of Mn oxide of birnessite type. It is also speculated that the crystal phase (channel structure) can be another determining criterion for ORR kinetics at manganese oxides.
Additionally, the observed larger inner-spacing between nanoparticles in Co 3 O 4 /La 2 O 3 ( Figure 3) in comparison to dense structure of MnO 6 octahedral sheet of birnessite MnO 2 , provides more active surface area that is more accessible to the electrolyte (reactant). In addition, it is reported that Co 3 O 4 has high affinity toward O 2 molecules, which enables better oxygen transport within its porous structure [61].
This all contributed to the observed behavior that the  [43]. This likely can be another reason for the lower catalytic activity of our MnO 2 /Co 3 O 4 oxides catalysts. Although the synergic effect of MnO 2 and Co 3 O 4 oxides has been reported in many publications to increase ORR activity [43,45], the investigation of the parameters such as the composition, crystalline structure, and morphology are to be investigated in order to propose the most probable synergy mechanism.
Since the synthesized hybrid materials have different compositions, and consequently structures, the kinetic comparison would be more informative if would be presented as activity (currents) per mol of Co 3 O 4 and MnO 2 . Figure 9 presents the comparison of molar activities with respect to Co 3 O 4 for the samples containing Co oxide, and with respect to MnO 2 for the samples synthesized at 500 and 600 • C, taking into account the compositions found by EDS ( Table 1). As can be seen from Figure 9a, the Co 3 O 4 /La 2 O 3 electrode is of higher activity at the beginning (at lower overpotentials) due to a different ORR reaction mechanism occurring in comparison to the Mn-based electrodes (additionally involves the Mn oxide electrochemical transformations). However, in the region of higher overpotentials that are more relevant for the electrochemical devices (fuel cells, batteries), the electrodes based on synergy of Mn/Co oxides outperform the electrode without Mn (Co 3 O 4 /La 2 O 3 ). This result is somewhat contrary to the presented performance of the current calculated per mass (Figure 8), which indicated the electrode without Mn (Co 3 O 4 /La 2 O 3 ) as the one of best performances. In addition, Figure 9b shows that trends of molar activities of MnO 2 -containing electrodes are similar to those of mass activity (Figure 5b). This clearly emphasizes the importance of the calculations to take into consideration the mole fractions in hybrid materials of different compositions in order to quantify the synergy effects.
ORR reaction mechanism occurring in comparison to the Mn-based electrodes (addi tionally involves the Mn oxide electrochemical transformations). However, in the region of higher overpotentials that are more relevant for the electrochemical devices (fuel cells batteries), the electrodes based on synergy of Mn/Co oxides outperform the electrode without Mn (Co3O4/La2O3). This result is somewhat contrary to the presented perfor mance of the current calculated per mass (Figure 8), which indicated the electrode without Mn (Co3O4/La2O3) as the one of best performances. In addition, Figure 9b shows that trends of molar activities of MnO2-containing electrodes are similar to those of mass activity (Figure 5b). This clearly emphasizes the importance of the calculations to take into consideration the mole fractions in hybrid materials of different compositions in order to quantify the synergy effects.

Conclusions
In summary, highly active electrocatalysts based on Mn and rare earth oxides with Co 3 O 4 for ORR, have been successfully synthesized using the ultrasonic spray pyrolysis process. For the sake of comparison, the hybrid materials with and without Mn oxides were investigated.
It was shown that different Mn oxides were well incorporated in the Co 3 O 4 matrix. Different synthesis temperatures led to the formation of two different manganese oxidesbirnessite type δ-MnO 2 at 500 and 600 • C, and manganese (II, III) oxide-Mn 3 O 4 at 800 • C. The catalysts morphology has been also affected by the state of Mn oxide. SEM images reveal flower-like nanosheets for hybrid materials with birnessite-MnO 2 and well-defined spherical nanoparticles for material based on Mn 3 O 4 and for the material based only on Co as catalysts (Co 3 O 4 /La 2 O 3 ). The electrochemical performance of MnO x /Co 3 O 4 and Co 3 O 4 /La 2 O 3 demonstrate a comparable ORR activity to Pt/C and superior activity to the pristine Mn oxide electrodes. It was shown that the mass activity of synthesized hybrid materials not supported on carbon blacks outperforms the literature values of carbon-based materials. Mass activity performance was compared to the molar activity-calculated per mol of the Mn and Co oxides being in charge for the catalytic performance in oxygen reduction reaction. It was revealed that the synergic coupling of Mn oxides and Co 3 O 4 have better catalytic performance in comparison to the electrodes based on pristine MnO 2 and Co 3 O 4 /La 2 O 3 . It was found that molar and mass activities give different information, since different amounts of active components are affecting the synergistic catalysis.
The crystal structure and morphological characteristics, as well as right amounts of investigated oxides, play the crucial role for high catalytic activity. Taking into account that the investigated materials are very low-cost materials especially compared to the state-of-the-art Pt/C-based electrodes, the demonstrated hybrid materials are promising catalysts for practical application for rechargeable metal-air batteries and fuel cells.  Data Availability Statement: All available data is contained within the article.