A Study on the Flow Resistance of Fluids Flowing in the Engine Oil-Cooler Chosen

: Oil-coolers are necessary components in high performance diesel engines. The heat removed by the cooler is a component in the total heat rejection via the engine coolant. Oil-cooler absorbs the heat rejected during the piston cooling and engine rubbing friction power loss. During ﬂows of both coolant and engine oil via the oil-cooler, some ﬂow resistances occur. The aim of the study is to determine values of the ﬂow resistance coefﬁcient for oil going through the cooler at various temperatures. The test stand was developed to determine time needed to empty tanks from liquids ﬂowing through oil-cooler. The ﬂow model was elaborated to study the mentioned ﬂow resistance coefﬁcient with respect to changing liquid temperature. The 20 ◦ C increase in liquid temperature resulted in a ﬂow resistance coefﬁcient decrease of 30% for coolant and of the much more for engine oil. It was found that better results would be achieved with ﬂows forced by means of pumps instead of using gravitational forces on the test stand.


Introduction
To provide their high performances and low emissions many heavy-duty direct injection (DI) compress ignition (CI) engines possess oil-coolers utilizing the engine coolant for heat transfer therein. The heat took out by the oil-cooler is a component in the total heat rejection via an engine coolant. Oil-cooler obtains the heat rejected during the piston cooling and the one resulted from the engine rubbing friction power loss.
According to [1] the total rubbing friction can be estimated by subtracting the numerically determined pumping loss and accessory power from the measured engine motoring power.
The engine accessories' power comprises ones of the water pump, the oil pump, the fuel pump, and the alternator.
The motoring power can be estimated using the Willan's line [2], where a chart of fuel flow rate as a function of the brake mean effective pressure (BMEP) allows an extrapolation to zero fuel flow rate. Such rate is needed to estimate the motoring mean effective pressure (MEP) or power.
Taraza et al. [3] elaborated a global friction model considering the individual friction components (e.g., piston assembly, bearings, valvetrain) and auxiliaries (injection pump, oil one, and coolant one). This global model allowed an enhancement in simulation accuracy both for steady state and transient engine operations.
Mitan et al. [70] studied the effect of commercial oil additive (COA) to mineral and semi-synthetic lubricants performance in four-stroke motorcycle engine.
A complex tribological model of piston-assembly lubrication dynamics was reported in [71].

Application of the Oil-Coolers
According to Wittebrood et al. [72] vehicle engines often utilize plate-type oil-coolers. The plate heat exchangers are commonly applied during vacuum manufacturing. The components of such exchanger are brazed with vacuum brazing. The latter is used for products requiring excellent internal cleanliness. It is needed to prevent any flux residue to be carried into the engine by the cooled oil as it may cause wear. In some cases, it is necessary to avoid the coolant side interaction with residual brazing flux.
Palmgren and Wallborg [73] present five concepts of improved oil-coolers and numerically evaluated their performances.
Sarma et al. [74] studied theoretically the properties of engine oil crossflow heat exchanger cooled with cold air at various flight altitudes. The effect of temperature in the oil ducts on the properties of engine oil was considered there. The results of theoretical predictions were compared with the conventional empirical equations of heat transfer presented in literature. It was found that the calculated effectiveness of the heat exchanger enhanced with the altitude of the flight. Additionally, the thermal properties varied with the altitude and hence the effectiveness of the heat exchanger in turn depended on Reynolds Number of the hot and cold fluids, number of transfer units, and specific heat variations.
Di Battista and Cipollone [75] utilized the heat from exhaust gases to warm up an engine oil. Researchers tested a turbocharged engine (F1C 3L IVECO), with the oil circuit modified to heat up the oil during the cold phase of the driving by the exhaust gases. A significant decrease in fuel consumption and pollutant emissions for an engine tested has been reported.
Rajpoot et al. [76] conducted the optimization of the finned tube oil/water cooler for hydro-electric turbine guide bearing application by effective utilization of fin area.
Azadi and Azadi [77] analyzed the failure of a heat exchanger used for cooling the oil in a marine diesel engine during its operation in the marine environment.
It was found that very little information is available relative to the resistance to flow for liquids flowing via oil-coolers.

Oil-Cooler Studied
An engine oil-cooler ( Figure 1) using the engine coolant was used for the tests. The flow diagram through that cooler is shown in Figure 2. The warm coolant flows to the engine radiator. There, the heat from the coolant is picked up by the airflow blowing the radiator.    The tested oil-cooler model was installed in the car models presented in Table 1. The tested oil-cooler model was the one installed in the FORD MONDEO MK3. Such cooler was installed in the engine version given in Table 2. The heated oil from the engine flows into the oil-cooler through one collective channel, which is then divided into several parallel flow paths with complex geometries. Then the cool liquid is led through one collective channel to the oil-cooler and then divided into several parallel flow paths with complex geometry. The portion of surface bounding the volume of the path through which the oil flows in the cooler is circumscribed by extruded aluminum ribs washed by coolant flowing in adjacent flow paths. The upstream and downstream flow paths contain the flowing coolant. The heat from the heated oil is transferred to the cool coolant. The mentioned ribbing intensifies the heat transfer between the flowing oil and the coolant. The cooled oil flows further to the engine lubrication system. The warm coolant flows to the engine radiator. There, the heat from the coolant is picked up by the airflow blowing the radiator.
The tested oil-cooler model was installed in the car models presented in Table 1. The tested oil-cooler model was the one installed in the FORD MONDEO MK3. Such cooler was installed in the engine version given in Table 2.

The Oil Studied
For the engines applied in FORD Mondeo MK3 one oil type is predestined [78], as specified in Table 3. Such oil can be supplied by various manufacturers. However, its properties, particularly viscosity and density can differ from each other [79], as shown in Table 4.   [80].
The kinematic viscosity ν is related to the dynamic one µ via Equation (1) where ρ(T)-density of oil as a function of temperature, given and tabulated in [81].
To estimate the dynamic viscosity of oil at temperature values different than these equal to 40 or 100 • C the Equation (2) based in the Andrade equation [82] was used where A [Pas]-the proportional factor, B [1/K]-the exponent factor.

The Coolant Studied
For the engines applied in FORD Mondeo MK3 various coolants from various manufacturers [83] can be applied, as specified in Table 5. Table 5. Properties of engine coolant from various manufacturers.

Product
Line/ Version For the tests conducted it was chosen the engine coolant MANNOL AF13++, Highperformance. It was assumed that it is a mixture contain 50% ethanediol, 0.2% sodium hydroxide, and 49.8% distilled water. Omitting the amount of sodium hydroxide in the mixture, due its small value, the MANNOL coolant can be treated as the 50/50 mixture of ethanediol and distilled water. The dynamic viscosity of such mixture is equal to 3.192 × 10 −3 Pa·s at the temperature of 20 • C and to 0.979 × 10 −3 Pa·s at the temperature of 40 • C [84]. The density of such mixture is equal to 1079 kg/m 3 at the temperature of 20 • C and to 1067 kg/m 3 at the temperature of 40 • C [84].

Hydraulic Diagram of the Test Stand
The diagram of the hydraulic system of the test stand is shown in Figure 3. The system comprises the upper oil tank 1, the upper coolant tank 2; thermometers 3; the shut-off valves 4, the oil-cooler studied 5, the lower oil tank 6 and the lower coolant tank 7.

Hydraulic Diagram of The Test Stand
The diagram of the hydraulic system of the test stand is shown in Figure 3. The system comprises the upper oil tank 1, the upper coolant tank 2; thermometers 3; the shutoff valves 4, the oil-cooler studied 5, the lower oil tank 6 and the lower coolant tank 7. In the test stand, the flows of heat-exchanging fluids in the tested oil-cooler were carried out by gravity, by using the differences in the height of the respective tanks: upper and lower. In addition, thermometers were installed in the hydraulic system of the stand, measuring the temperature of the coolant and oil in characteristic places.

Design of The Test Stand
The completed test stand is presented in Figure 4.  In the test stand, the flows of heat-exchanging fluids in the tested oil-cooler were carried out by gravity, by using the differences in the height of the respective tanks: upper and lower. In addition, thermometers were installed in the hydraulic system of the stand, measuring the temperature of the coolant and oil in characteristic places.

Design of the Test Stand
The completed test stand is presented in Figure 4. The diagram of the hydraulic system of the test stand is shown in Figure 3. The system comprises the upper oil tank 1, the upper coolant tank 2; thermometers 3; the shutoff valves 4, the oil-cooler studied 5, the lower oil tank 6 and the lower coolant tank 7. In the test stand, the flows of heat-exchanging fluids in the tested oil-cooler were carried out by gravity, by using the differences in the height of the respective tanks: upper and lower. In addition, thermometers were installed in the hydraulic system of the stand, measuring the temperature of the coolant and oil in characteristic places.

Design of The Test Stand
The completed test stand is presented in Figure 4.  The supporting structure of the test stand was based on a frame made of standard BOSCH 40 × 40 four-groove system profiles connected with each other by means of angle bracket, screws, and nuts. Three horizontal subframes (three levels) were made. Two tanks, called upper tanks, were attached to the upper level, one was filled with oil, the other with coolant. The upper tanks were attached to Fischer FLS 17/1 16 × 20 × 46 C-shaped mounting rails screwed to the frame and sealed with a special adhesive for sealing hydraulic systems. At the outlet of each upper tank there was a shut-off valve connected to a pipe made of plastic.
On the middle level, the tested oil-cooler was attached to the profile with a dedicated adapter. The cooler was attached with DIN EN ISO 7046-1 M6 × 16 screws to the 6 mm thick plates, which were bent at an angle of 90 • and fixed to the profile with screws ( Figure 5). The cooler has been installed in the same position as it was originally on the engine to maintain proper flow through the oil-cooler. Shut off valves were placed on the inlet and the outlet of the oil-cooler to allow for the entire system to be filled with liquids. The shut-off valves located on the inlet of the oil-cooler are connected to the appropriate shut-off valves at the outlets of the upper tanks. On the other hand, the shut-off valves located on the outlet of the oil-cooler are connected to the appropriate shut-off valves located at the inlets of the lower tanks. The supporting structure of the test stand was based on a frame made of standard BOSCH 40 × 40 four-groove system profiles connected with each other by means of angle bracket, screws, and nuts. Three horizontal subframes (three levels) were made. Two tanks, called upper tanks, were attached to the upper level, one was filled with oil, the other with coolant. The upper tanks were attached to Fischer FLS 17/1 16 × 20 × 46 Cshaped mounting rails screwed to the frame and sealed with a special adhesive for sealing hydraulic systems. At the outlet of each upper tank there was a shut-off valve connected to a pipe made of plastic.
On the middle level, the tested oil-cooler was attached to the profile with a dedicated adapter. The cooler was attached with DIN EN ISO 7046-1 M6 × 16 screws to the 6 mm thick plates, which were bent at an angle of 90° and fixed to the profile with screws ( Figure 5). The cooler has been installed in the same position as it was originally on the engine to maintain proper flow through the oil-cooler. Shut off valves were placed on the inlet and the outlet of the oil-cooler to allow for the entire system to be filled with liquids. The shutoff valves located on the inlet of the oil-cooler are connected to the appropriate shut-off valves at the outlets of the upper tanks. On the other hand, the shut-off valves located on the outlet of the oil-cooler are connected to the appropriate shut-off valves located at the inlets of the lower tanks. On the bottom level, afore mentioned bottom tanks were attached to Fischer FLS 17/1 16 × 20 × 46 C-shaped mounting rails screwed to the subframe and sealed with a special adhesive for sealing hydraulic systems. At the inlet of each bottom tank there was a shutoff valve connected to a pipe made of plastic.
The distance between the levels was 600 mm (Figure 6), which allowed the fluid to flow freely, and the conduit used was routed as straight as possible to limit the flow resistance. On the bottom level, afore mentioned bottom tanks were attached to Fischer FLS 17/1 16 × 20 × 46 C-shaped mounting rails screwed to the subframe and sealed with a special adhesive for sealing hydraulic systems. At the inlet of each bottom tank there was a shut-off valve connected to a pipe made of plastic.
The distance between the levels was 600 mm (Figure 6), which allowed the fluid to flow freely, and the conduit used was routed as straight as possible to limit the flow resistance. Four identical digital thermometers were used to monitor the temperature of the liquids. Temperature was measured on the inlet of the oil-cooler and on the inlet of the lower tank ( Figure 7). Such setup of thermometers was performed in both two flow lines of the tested liquids. Four identical digital thermometers were used to monitor the temperature of the liquids. Temperature was measured on the inlet of the oil-cooler and on the inlet of the lower tank (Figure 7). Such setup of thermometers was performed in both two flow lines of the tested liquids. Four identical digital thermometers were used to monitor the temperature of the liquids. Temperature was measured on the inlet of the oil-cooler and on the inlet of the lower tank ( Figure 7). Such setup of thermometers was performed in both two flow lines of the tested liquids.

The Determination of Resistance to Flow through the Oil-Cooler
Determining of resistance to flow of the liquid studied through the oi-cooler or the replacing it short section of plastic pipe was conducted using the model presented in

The Determination of Resistance to Flow through the Oil-Cooler
Determining of resistance to flow of the liquid studied through the oi-cooler or the replacing it short section of plastic pipe was conducted using the model presented in Figure 8. The liquid studied flows from the upper tank successively through: the outlet shut-off valve connected to the upper tank, characterized by the local flow losses factor ζ 1 = 0.24 [85], -the plastic pipe section with length l 1 = 10 mm and inner diameter d = 15 mm, characterized by the length loss factor ζ 1 [85], -the elbow pipe section, characterized by the local flow losses factor ζ 2 = 0.132 [85], -the plastic pipe section with length l 2 = 620 mm and inner diameter d, characterized by the length loss factor ζ 2 [85], -the elbow pipe section, characterized by the local flow losses factor ζ 3 = 0.132 [85], -the plastic pipe section with length l 3 = 250 mm and inner diameter d, characterized by the the length loss factor ζ 3 [85], -the inlet shut-off valve connected to the oil-cooler or to the alternative short section of plastic pipe, characterized by the local flow losses factor ζ 4 = 0.24 [85], -the oil-cooler characterized by the coefficient of resistance to flow α, or the alternative short section of plastic pipe with length l 4 = 80 mm and inner diameter d, characterized by the length loss factor ζ 4 [85], -the outlet shut-off valve connected to the oil-cooler or to the alternative short section of plastic pipe, characterized by the local flow losses factor ζ 5 = 0.24 [85], -the plastic pipe section with length l 5 = 200 mm and inner diameter d, characterized by the length loss factor ζ 5 [85], -the elbow pipe section, characterized by the local flow losses factor ζ 6 = 0.132 [85], -the plastic pipe section with length l 6 = 300 mm and inner diameter d, characterized by the length loss factor ζ 6 [85], -the elbow pipe section, characterized by the local flow losses factor ζ 7 = 0.132 [85], where = 9.81 m/s 2 -acceleration due to gravity, -density of the liquid studied, ∑ ℎ -the sum of the flow losses determined from Equation (4) where ℎ -flow losses in the pipe section of length , determined from Equation (5) where  -the length loss factor for the pipe section of length , -the linear resistance coefficient, for the assumed laminar flow, • -Reynolds number,the kinematic viscosity of liquid studied, ℎ -local flow losses at , determined from Equa- where ζ -the local flow losses factor. The flow speed of liquid studied in the upper tank-due to a much larger cross-sectional area of the upper tank in relation to the cross-sectional area of the inlet hole of the bottom tank ( ≫ )-is negligible ( 0). Therefore, Equation (3) can be simplified to the form (7) and then it can be obtained Equation (8) allowing determination of the flow speed [v(z t )] 2 2·g where g = 9.81 m/s 2 -acceleration due to gravity, ρ-density of the liquid studied, ∑ h lossesthe sum of the flow losses determined from Equation (4) where h li -flow losses in the pipe section of length l i , determined from Equation (5) [85] where ξ i = λ l i d -the length loss factor for the pipe section of length l i , λ = 64 Re -the linear resistance coefficient, for the assumed laminar flow, Re ≈ v(z b )·d ν -Reynolds number, ν-the kinematic viscosity of liquid studied, h j -local flow losses at j, determined from Equation (6) [85] where ζ j -the local flow losses factor. The flow speed v(z t ) of liquid studied in the upper tank-due to a much larger cross-sectional area of the upper tank in relation to the cross-sectional area of the inlet hole of the bottom tank (A t A o )-is negligible (v(z t ) ≈ 0). Therefore, Equation (3) can be simplified to the form (7) and then it can be obtained Equation (8) The flow speed can be the solution of the Equation (9) [ which is given by the Equation (10) v The flow rate balance is given by Equation (11) − After rearranging of Equation (12) it was obtained the Formula (13) For the case of the liquid flowing through the oil-cooler the time T oc of emptying the upper tank was determined from the Equation (14) where v(z bo−c )-flow speed v(z b ) for the case of liquid flowing through the oil-cooler. For the case of the liquid flowing through the alternative short plastic pipe section, the time T p of emptying the upper tank was determined from the Equation (15) where v z bp -flow speed v(z b ) for the case of liquid flowing through the alternative short plastic pipe section. From Equations (10), (14) and (15) the parameter α can be numerically determined. After rearrangement of Equation (15) we obtain Equation (16) 32·ν·v z bp Its solution is given by Equation (17) v From the evenness of the flowing volumes of liquid we obtained Equation (18) v z bp ·T p = v(z boc )·T oc , After re-arrangement of Equation (14) we obtain Equation (19) 32·ν·v(z boc ) Substituting Equation (18) in Equation (19), after rearrangement we obtained Equation (20) for the coefficient α The flow rate of liquid flowing through the oil-cooler was determined from Equation (21) .
where ρ-density of the liquid studied flowing through the oil-cooler, A oc = πd 2 oc 4 -cross section area of the inlet hole of the oil-cooler, d oc = 12 mm-diameter of the inlet hole of the oil-cooler.
The pressure drops ∆p caused by liquid studied flowing through the oil-cooler was estimated from Equation (22)

Measurement Procedure
During the tests, the resistance to the flow of engine oil and engine coolant through the oil-cooler was measured. The measurement took place at two room temperatures of 20 • C and 40 • C.
First, the total flow resistance was determined in the flow lines of the tested liquids on the stand outside the oil-cooler. The mentioned resistances were caused by the presence of shut-off valves and relatively long lines between the tanks and the oil-cooler. During the measurement of those resistances, the oil-cooler was replaced with short sections of plastic pipes with an internal diameter of 15 mm and a length of 80 mm, which were connected to the appropriate shut-off valves.
For two room temperatures of 20 • C and 40 • C, respectively, were measured separately:  In the next phase of testing at the stand, the short sections of plastic pipes were removed, and the shut-off valves were connected to the relevant stub pipes of the oil-cooler.
For a room temperature of 40 °C, it was measured separately: When the coolant was not circulating through the oil cooler, the time of flow of oil could not be determined with a high confidence level. This was due to an increased flow resistance caused by higher oil density at tested temperature. Air was appearing in the pipes between the upper oil tank and the oil-cooler, and it was very difficult to remove it during the measurement. Therefore, the results of measurements for this case could be considered as the coarse ones.
During all the measurements carried out, the temperature of the fluids was controlled in the designated places. There were no differences between the room temperature and the temperature of the flowing test liquid.
In all tested cases, filling the upper tanks with coolant and engine oil, respectively, took place with the outlet shut-off valves of the upper tanks closed. After the upper tank was half filled with the liquid, the outlet shut-off valve of the upper tank was opened, which allowed for gradual filling of the pipe between the outlet shut-off valve of the upper tank and the inlet shut-off valve connected to the cooler or the alternative short section of plastic pipe. After filling said pipe, the outlet shut-off valve connected to the radiator or to the alternative short piece of plastic pipe was opened. This made it possible to gradually fill the relevant main line in the oil-cooler with liquid or a short section of plastic pipe replacing this cooler. Finally, the outlet shut-off valve connected to the oil-cooler or a short piece of plastic pipe replacing of the oil-cooler was opened and the test liquid gradually In the next phase of testing at the stand, the short sections of plastic pipes were removed, and the shut-off valves were connected to the relevant stub pipes of the oil-cooler.
For a room temperature of 40 • C, it was measured separately: When the coolant was not circulating through the oil cooler, the time of flow of oil could not be determined with a high confidence level. This was due to an increased flow resistance caused by higher oil density at tested temperature. Air was appearing in the pipes between the upper oil tank and the oil-cooler, and it was very difficult to remove it during the measurement. Therefore, the results of measurements for this case could be considered as the coarse ones.
During all the measurements carried out, the temperature of the fluids was controlled in the designated places. There were no differences between the room temperature and the temperature of the flowing test liquid.
In all tested cases, filling the upper tanks with coolant and engine oil, respectively, took place with the outlet shut-off valves of the upper tanks closed. After the upper tank was half filled with the liquid, the outlet shut-off valve of the upper tank was opened, which allowed for gradual filling of the pipe between the outlet shut-off valve of the upper tank and the inlet shut-off valve connected to the cooler or the alternative short section of plastic pipe. After filling said pipe, the outlet shut-off valve connected to the radiator or to the alternative short piece of plastic pipe was opened. This made it possible to gradually fill the relevant main line in the oil-cooler with liquid or a short section of plastic pipe replacing this cooler. Finally, the outlet shut-off valve connected to the oil-cooler or a short piece of plastic pipe replacing of the oil-cooler was opened and the test liquid gradually drained into the lower tank. Such successive opening of the shut-off valves was dictated by safety considerations to properly identify and early eliminate possible leaks in connections and prevent unnecessary loss of tested liquids. It also partially prevented the formation of air bubbles and facilitated their evacuation to the upper reservoir by deliberately repeatedly moving (deflecting from the original position) the lines filled with the tested liquid. During the flow from the upper to the lower tank, the liquid level in the upper tank was lowered and the tested liquid had to be replenished until the visible air bubbles in the conduits were eliminated. Then the outlet cut-off valve connected to the oil-cooler or a short piece of plastic pipe replacing of the oil-cooler was closed, and the liquid in the upper tank was replenished until the assumed upper (primary) level was reached. At that time, the stand was considered ready for flow time measurement. The test liquid accumulating in the lower tank can be poured through the outlet shut-off valve located at the bottom of the lower tank into a separate canister and re-poured into the upper tank if necessary. The flow time was measured from the moment of reopening the outlet cut-off valve connected to the oil-cooler or a short piece of plastic pipe replacing of the oil-cooler until the assumed lower level of the tested liquid in the upper tank was reached. The time control was carried out with the use of a camera tracking the changes in the position of the liquid surface tested in the upper tank.

Results and Discussion
The obtained values of kinematic viscosity of the coolant and oil studied were presented in Table 6. An increase of the temperature with 20 • C resulted in the decrease of the kinematic viscosity, namely, the 3.22-fold one for the coolant and the 2.47-fold one for the engine oil, respectively. The measured values of time needed to empty the upper tank from liquids flowing under various conditions were presented in Table 7. An increase of the temperature with 20 • C resulted in the decrease of the time necessary for the emptying of the upper tank, namely, the 1.25-fold one and the 1.22-fold one for the coolant flowing via oil-cooler and via short plastic pipe section, respectively. Similarly, the mentioned increase in temperature resulted in a much higher decrease of the time needed for the emptying of the upper tank, namely, the 1.56-fold one and the 1.29-fold one for the engine oil flowing via an oil-cooler and via a short plastic pipe section, respectively. The obtained values of the coefficient of resistance to flow α were shown in Table 8. An increase of the temperature with 20 • C resulted in the decrease of the coefficient of resistance to flow α, namely, the 1.43-fold one and the 61-fold one for the coolant and the engine oil, respectively. The obtained values of the flow speed for the liquids studied and relative flow rate and pressure drop-in oil-cooler were showed in Table 9. The obtained value of pressure drop caused at 20 • C by an engine oil flowing through the oil-cooler was close to that reported in [49], obtained for the other type of oil-cooler applied in the diesel engine, for the minimal flow rate reported, which was by two orders higher compared to the case of oil analyzed during the present study. However, the temperature of an engine oil supplied to the oil-cooler described in [49] was also much higher resulting in the lower values of the oil viscosity. At the temperature of 40 • C the pressure drop was about 1.4-fold and 1.1-fold lower for a coolant and an engine oil, respectively than that at temperature of 20 • C.

Conclusions
Based on the results obtained, we have made some conclusions: 1.
The analyzed oil-cooler was filled with engine oils SAE 5W-30 viscosity. Considering different manufacturers, the kinematic viscosity and density differed from one another. Apart from that, some manufacturers specified the oil density at 15 • C, while the others used 20 • C. Many manufacturers did not report exact values for the mentioned quantities at all.

2.
Similarly, the studied oil-cooler was also filled with coolants supplied by different manufacturers. Those coolants differed from one another by its kinematic viscosity and density. Some of manufacturers specified the values of these quantities determined at a temperature of 20 • C, but most of them did not provide such values. 3.
The test stand allowed for the time estimation of emptying the upper tanks from a coolant and an engine oil flowing via the oil-cooler studied. 4.
The flow model allowed for estimation of flow resistance coefficient α for the coolant and the engine oil flowing through the oil-cooler.

5.
Obtained values of flow resistance coefficient α were affected by the temperature. An increase in temperature from 20 • C to 40 • C resulted in a decrease in flow resistance coefficient α, namely, the 1.43-fold one and the 61-fold one for the coolant and the engine oil, respectively.

6.
As the engines are using pumps to force the fluids, instead of using gravity, the flow model needs to be further developed to consider the possibility of forcing oil and coolant temperature changes.