Cavitation Morphology Study between Hemispherical Textured Rotating Friction Pairs

: A non-direct contact rotary interface uses a viscous fluid as the lubricant working medium. Because the oil film friction coefficient formed is extremely small, so it has great application potential in sealing, fluid transmission, thermosolutal convection, and bionics. Research on mechanical seals, wet clutches, and dynamic load bearing have proven that micro-textures can effectively improve friction and lubrication performance. However, when the fluid flows through the texture boundary, pressure disturbances can induce hydrodynamic cavitation. A pair of rotating disks are selected as our research objects. From the simulation and experiment research, we found that cavitation volume does not always increase with an increase in the texture rate, and cavitation always occurs preferentially at the outer diameter, so it is necessary to avoid machining the texture structure at the outer diameter of the mechanical seal end. Once the conditions for cavitation are met, a com-plete cavity is formed in approximately 0.015 s. The study also verifies that the cavitation gas origi-nates from the phase change of the oil.


Introduction
The first step in our perceptual understanding of cavitation came in 1893, when the speed of a British destroyer suddenly dropped during a voyage. A later inspection found that there were several perforations caused by cavitation effects on the propeller. Hydrodynamic cavitation is actually a phase transformation and an intricate transient microscopic phenomenon. Cavitations are usually detrimental to hydraulic machinery. When cavitation bubbles collapse, they can release tremendous energy into the surrounding fluid [1], produce local high temperatures (2300 K-4600 K) [2] and high pressures (1000 bar) [3], produce shock waves [4], damage the mechanical surface [5] (Figure 1), corrode the flow channel, and affect the service life and safety of hydraulic machinery. Therefore, it is of great significance to study the mechanism of cavitation and reduce cavitation occurrence in hydraulic machinery. To date, there has been abundant research on the effects of flow fields and cavitation on hydraulic machinery. In 1998, Schouveiler et al., studied oil flow between the stationary disk and the rotating disk and found that when the Reynolds value was high, the turbulent flow broke the periodicity of the oil flow, and secondary flow appeared at the outer diameter [6]. Subsequently, Soong et al., analyzed the flow structure of oil between disks by the paraffin fluorescence method and found that, when the rotational speed of two disks is the same and the Reynolds number is increased, the flow field will be stable then complex and then stable again, which verified the secondary flow phenomenon discovered by Schouveiler [7]. Bilal [8] found that the fluid momentum response decreases with Reynolds number and Deborah number. Shah [9][10][11] revealed the characteristics of water-based hybrid nanofluid flows dispersed by single-walled carbon nanotubes and found that the concentration distribution decreases with increasing Reynolds number due to the dominant effect of inertial forces. In 2016, Pahlovy et al. established a mathematical model of drag torque based on two rotating coaxial disks and analyzed the influence of speed difference, clearance of friction pairs, and other parameters on drag torque [12]. They set up a visual test bed and collected the flow states between friction pairs and eventually found that the theoretical results were basically consistent with the change trends of the test results [13]. Pratomo et al. studied cavitation using the Zwart-Gerber-Belamri model based on the commercial computational fluid dynamics (CFD) software ANSYS. It was found that the cavitation model has a great influence on the performance of the system and that neglecting cavitation leads to the misalignment of the pressure distribution and verified the importance of considering cavitation effects when studying hydrodynamic systems [14]. Thomas Neupert et al., established a torque transfer model that considered the radial grooves of friction disks and analyzed the influence of oil viscosity temperature characteristics and gas-liquid two-phase flow on the transfer torque. It was found that groove structural parameters influence the transfer torque [15]. Liangyan et al., studied the performance characteristics of journal bearings lubricated with coupled stress fluid and established a modified Reynolds equation of coupled stress lubrication that considered the viscous effect and found that the viscous effect can improve the viscosity, friction coefficient, and maximum film pressure [16]. S. Klingl et al., demonstrated that different types of rotating disk boundary layers are absolutely unstable, and for radial inward and outward flow, no absolute instability is found for narrow disc spacing and merging boundary layers [17].
Cavitation is generally considered to have negative effects on hydraulic machinery. Muhammad Yusvika et al., analyzed that cavitation on ship propellers would cause vibrations and noise [18]. Matevž Dular et al., used two high-speed cameras to capture the movement and collapse process of cavitation bubbles, which produce circular dimples in the aluminum film when they collapse [19]. Marcio Abreu et al., found that heavy diesel engines are most likely to be destroyed by cavitation erosion in the part exposed to liquid [20]. Xinping Long et al., found that intensive cavitation phenomenon in a jet fish pump causes dangerous flow in the surrounding flow field and increases the pressure [21]. Conversely, cavitation also has many promising applications, such as surface cleaning [22], emulsification [23], sonophoresis [24], etc. Simulations and experiments are usually used to analyze cavitation effects. Hidalgo used the Zwart-Gerber-Belamri cavitation model to analyze the three-dimensional unsteady cavitation flow around the plane convex hydrofoil, and the numerical results clearly showed the processes of cavitation development, shedding, and collapse under high-speed cavitation [25]. Qureshi et al. [26] studied flow behavior of non-Newtonian fluid through orthogonal porous surfaces, and researched the heat flux and mass transfer source of non-Newtonian CNT fluid. Pahlovy et al., observed the flow state of oil between friction disks on rough surfaces using a visual wet clutch test rig and found that few long strip bubbles appeared under low rotational speed and that the number and volume of bubbles increased with an increase in rotational speed [27]. Ebrahim et al. researched high-speed visualization of cavitation using a cavitation generator, analyzed the spatial structure and time evolution of local cavitation in non-constant flow regime, and found that for a cylindrical vacuole generator can effectively mitigate large-scale cloud cavitation [28]. Boubendir et al. investigated the effect of using non-Newtonian fluids as lubricants to analyze the performance of multi-self-lubricating porous plain bearings and found that non-Newtonian fluids reduced the bearing load-bearing performance compared to Newtonian lubricants [29]. Batchelor [30] and Stewartson [31] were the first to study the fluid flow in a system of infinitely large double rotating disks based on the study of single-disk flow. Batchelor simplified the control equations for incompressible axisymmetric flow and obtained the corresponding set of ordinary differential equations. He pointed out that in co-rotating and rotor-stator systems, a fluid boundary layer is formed on the surface of both disks, and radial flow occurs mainly inside the boundary layer. In the "inviscid core" between the two boundary layers, the fluid rotates with constant angular velocity as a rigid body without radial flow, and Stewartson solves a similar set of equations for the flow of two infinitely large rotating disks in Reynolds number power form. A different conclusion from Batchelor was obtained. He proposed that in a system of rotating disks, the boundary layer is formed only on the surface of the rotating disk, while the fluid between the disks remains stationary.
Prior work found that the surface texturing of friction pairs can effectively improve the lubrication performance and increase the bearing capacity. Mizuki et al., visualized the flow of lubricating oil on the texture surface using fluorescent particles as tracking targets. By observing particles' movement, they found that the flow speed of lubricating oil in texture dimples decreased significantly [32]. Lbatan et al., studied the boundary friction of friction pairs and subsequently found that oil stored in the micro-cavity of negative surface texture dimples can effectively trap abrasive particles to reduce further wear. At high speeds, the dynamic pressure generated by micro-dimples can effectively prevent direct contact with the friction disk [33]. Fan et al. studied the working performance of surface texture with uncertain size using a statistical model and found that the most critical geometric parameter affecting liquid film lubrication is texture dimple depth, and the key parameter affecting liquid film bearing capacity is the proportion of texture area [34]. Slawomir et al. carried out friction tests on textured surfaces and polished surfaces at room temperature and high temperature (80 °C ) using a needle disc friction test machine. The tested components were lubricated with different oils, and it was found that texture always produced beneficial lubrication performance [35]. Weili et al. proposed a method that combined surface deformation with longitudinal or transverse micro-vibration and found that vibration could pull out the lubricating oil trapped in texture dimples, thus increasing the thickness of the lubricating oil film and improving the bearing capacity [36].
Due to the literature summary, cavitation in hydromechanics has been extensively studied, but most of them focus on groove cavitation and cavitation macroscopic morphology. In this paper, the mechanism of cavitation induced by hemispherical texture is studied from microscopic view, and the relationship between pressure and cavitation, and the phase change law of vapor and oil fluid are visualized. The method of weakening cavitation is also proposed, which can provide reference for the design of surface structure of internal combustion engine cylinder, dynamic pressure bearing, and mechanical seal.
The simplified friction pair model is shown in Figure 2. The cavitation phenomena were simulated and experimentally analyzed. The specific implemented methodologies include governing equations analysis, geometric and CFD model study, CFX simulation research, test bench construction, and experimental result analysis. In addition, the change in cavitation bubble morphology, transfer between gas phase and liquid phase, and change in cavitation bubble structure were also systematically studied.

Multiphase Model
In cavitation flow calculation, the homogeneous flow model ignores the difference in gas-liquid two-phase flow parameters, so it is easier to converge [37], and the gas and liquid phases are treated as a single phase flow, as is shown in Figure 3, where R is the radius of the cavitation bubble and N2 is the number of cavitation bubbles. In addition, it is assumed that the gas phase and liquid phase have the same velocity and saturation temperature and that the parameter transport volume between the two phases is the same: where φ is a general scalar of the flow field, χ is the different phase of fluid and is generally presented as a subscript, ρ is the fluid density in kg/m 3 , NP is the phase number in the fluid, λ is the volume fraction of each phase, U is the vector velocity in m/s, Г is the phase diffusion ability in kg/(m·s), and SM is the mass source in kg/(m 3 ·s).

Turbulence Model
The shear stress transport (SST) turbulence model is one of the best comprehensive vortex viscosity models available and has been very widely used in recent years. Therefore, it is highly respected by model researchers and those who have experience in using turbulence models. The basic principle of the standard SST turbulence model is to use the k-ω model near the wall, and the k-ε model in the outer boundary layer and free shear. With the development of computational power in recent years, computational fluid dynamics has also developed rapidly, allowing one to use finer meshes and more accurate algorithms to compute more complex cases, such as large Eddy simulations. The application of the SST turbulence model to computational chemistry is more in the areas of combustion, explosions, and aerodynamic thermodynamics.
When oil flows into the dimple, vortex flow will be generated [38,39], so we select the turbulence model in the simulation calculation. The gap between the two friction plates is small, so the film thickness is very thin here, and since the SST model [39][40][41] has excellent applicability to the boundary layer and free shear layer of the film flow field, we selected this model for our research. The turbulent viscosity equation, k equation, ω equation, and weighting function equation are as follows [41]:  (9) where ωh is the turbulence frequency, Pk is the incidence of turbulence caused by viscous forces in kg/(m·s 3 ), μt and μ are the turbulent viscosity and dynamic viscosity, respectively, in kg/(m·s), υ is the kinematic viscosity in m 2 /s, y is the distance near the wall in m, Pkb and Pωb are buoyant turbulence terms, S′ is the strain rate, and the other constants are β″ = 0.09, β′ = 0.075, α = 5/9, σk = σω =2, σω2 =1/0.856.

Cavitation Model
In cavitation flow, there is convective exchange of mass and volume fractions between the gas phase and the liquid phase [37], where the transport equation of the gas volume is: where λv is the volume fraction of the gas phase, ρv is the gas density of the gas phase in kg/m3, u is the vector velocity of the gas phase in m/s, and ̇ is the source term for evaporation and condensation.
The Rayleigh-Plesset equation describes the growth of bubbles in liquids: (11) where RB is the cavitation bubble radius in m, pv is the pressure (saturated vapor pressure of liquid) in the cavitation bubble in Pa, p is the liquid pressure around the cavitation bubble in Pa, ρf and ρv are the liquid and vapor density, respectively, in kg/m 3 , and τ is the coefficient of the surface tension between the liquid and vapor in N•m.
By ignoring the second derivative term and the surface tension term, Equation (11) can be simplified as: The change rates of bubble volume and mass can be calculated as follows: If the number of bubbles per unit volume in fluid is NB, then the volume fraction of vapor in the fluid λv can be expressed as: then the total mass transfer rate between different phases (evaporation or condensation) per unit volume is: where F is the empirical correction coefficient, which means the difference in evaporation or condensation rate. Generally, evaporation is faster than condensation. Empirically, evaporation mainly occurs at the nucleation point and decreases the density at this location. Therefore, the mass transfer rate equation of the evaporation process needs to be modified [41].
where λnuc is the volume fraction in the nucleation center.

Mesh Model
As the flow is circumferential, the finite element model is designed as a sector with a center angle of 12°, inner radius of 27 mm, and outer radius of 32 mm. The default film thickness h0 is 0.1 mm and the default texture depth ht is 0.0564 mm. The flow field model is shown in Figure 4. When a separator plate is textured with regularly arranged micro-dimples, there will be a corresponding micro-convex, as is shown in Figure 5. When the texture rate is 3.205%, the distance between the two micro-convexes is 0.5 mm in the radial direction, and in the circumferential direction, the center angle of the two neighboring micro-dimples is 1°. Cavitation mainly occurs under high-speed conditions, so the default rotation speed n is 6000 rpm, inlet pressure p0 is 0.08 MPa, and initial oil temperature T0 is 293 K. Figure  6 shows the boundary conditions in the flow field. The properties of the oil and its vapor are shown in Table 1. Since temperature has a great influence on oil viscosity, a linear interpolation function is used to define the relationship between oil viscosity and temperature in CFX software [42].
where μx = 0.18 × 10 −3 Pa·s, T is the temperature in Celsius, and μ40 is the oil dynamic viscosity at a temperature of 40 °C in Pa•s.

Cavitation under Different Texture Rate
In order to test the influence of the quality of mesh division on the accuracy and convergence of the calculation results, different mesh division schemes were made. The cavitation volume fraction was chosen as a measure of computational convergence and stability, and the total volume fraction of cavitation of a single oil film under the default operating conditions was calculated using the CFX steady-state simulation method. As shown in Table 2, five meshing schemes were designed, and different O-grid layers were used in Schemes 1 and 2, and it was found that the cavitation volume increased significantly with more O-grid layers. In Schemes 3 and 4, the number of circumferential layers in the non-texture region has been increased and the cavitation volume fraction has remained essentially stable. In Scheme 5, the number of meshes increased significantly after the number of O-grid layers was continued to be increased, and the cavitation volume fraction remains unchanged. Therefore, in order to save computational time and take into account the convergence and stability of the calculation, scheme 4 is chosen as the final meshing division. The selected meshing parameters in this paper are as follows: 121 layers in the texture region, 124 layers in the non-texture region, and 11 layers in the O-grid. Texture, as a roughness element, is the leading cause of cavitation. The volume fraction is directly proportional to the cavitation intensity. First, the volume fraction of oil film cavitation is analyzed at the texture rates of 3.205%, 6.41%, and 12.917%. As is shown in Figure 7, when the texture rate is 0, there is no cavitation. Cavitation occurs when the texture ratio is 3.205%, but it is not obvious. When the texture rate is 6.41%, the cavitation volume fraction increases significantly, but when the texture rate is 12.917%, the value decreases, indicating that cavitation does not increase with an increase in texture rate. Therefore, we can surmise that there is an optimal texture rate that can reduce the occurrence of cavitation. Surface texture technology is widely used to increase the oil film load-bearing capacity in dynamic bearings and mechanical seals, but cavitation caused by texture is an unavoidable problem. Based on the results above, we can assume that there is an optimal weave rate that can combine the increase of oil film load capacity and the weakening of cavitation.  Figure 8 shows the morphology development of cavitation over time over 0.1 s. When the texture rate is 3.205%, the cavitation diffused along textured dimples into non-textured regions and developed rapidly between 0 and 0.013 s, with a volume fraction of 0.00063409. After 0.014 s, the cavitation volume fraction finally stabilizes at 0.00064191. After increasing the texture rate, the cavitation extends along the weave to the surrounding area. Figures 9 and 10 show similar patterns to Figure 8, so it is unnecessary to describe them.

Velocity Analysis in Cavitation Area
When the texture rate was 6.41% and the rotating speed was 6000 rpm, we researched the instantaneous relative velocity of the oil and cavitation gas in a specific area of the oil film. Part of the area in the upper left corner of the oil film was selected as the research object. In Figure 11, a1, a2, and a3 are velocity vectors of oil at different time nodes. Ripples around circles mean that hemispherical dimples cause severe flow field disturbance, and the flow field tends to be stable when away from the dimples. Accordingly, b1, b2, and b3 are velocity vectors of cavitation gas at the same position. By comparison, it can be clearly concluded that the direction of oil flow is strictly consistent with that of the cavitation gas. The gas flows with the oil, and the oil flows faster than the cavitation gas.

Pressure Analysis in Cavitation Area
Low pressure is an essential and significant element of cavitation occurrence. In our research, the saturated vapor pressure pv of oil was determined to be 1000 Pa; that is, cavitation occurs when the pressure in the flow field is lower than 1000 Pa. From Figures 9  and 13, we can see that texture dimples can definitely disturb the pressure distribution; however, except for the oil near the texture boundaries or dimples, the oil pressure distribution in other positions was evenly consistent, and the cavitation location was consistent with the low pressure area. The radial flow of oil is mainly driven by inlet pressure and centrifugal force, and flow velocity increases along the radial direction. According to Bernoulli's principle, the pressure distribution has the opposite trend from that of flow velocity distribution. It is known that the circular angle θ of an oil film model is 12°, and the radius of θ = 6° is on the center line of the radial texture dimple. Figure 14 shows that when there is no texture, the pressure decreases uniformly along the radial direction, and the pressure curve was smooth (origin 6°). When textured, the pressure drop curve was smooth in the non-textured area, and there were pressure fluctuations in the textured area.  Figure 15 shows the pressure distribution in a single texture dimple (0.9-1.1° is a nontexture area; 0.8-0.9° and 1.1-1.2° are texture areas). It can be seen that cavitation was induced by local low pressure that is lower than pv at the downstream boundary of the texture, local high pressure was generated in the upstream area of the texture boundary, and the peak value of local high pressure gradually decreased with time. It is worth mentioning that the analysis of cavitation pressure is concentrated on the pressure analysis of the whole flow field, and there is very little analysis of the pressure inside the weave at the micron scale. Figure 15. Pressure distribution at different times in a single hemispheric texture dimple.

Mass Transfer Analysis
Combined with the above analysis, we can conclude that cavitation occurs when the pressure in the texture dimple is lower than the saturation vapor pressure. The cavitation bubble gradually disappears when the pressure increases as cavitation is generated in the outer diameter (30.5 mm < r < 32 mm) and the cavitation volume fraction disappears around inner diameter (27 mm < r < 30.5 mm). That is, there are no directly observed bubbles. It is assumed that the gas-phase mass generation rate is negative and that the gasphase mass disappearance rate is positive to analyze the mass transfer between the gas and liquid phases when cavitation is generated. Figure 16 shows the cloud diagram of the instantaneous mass transfer rate of the gas phase in a single texture dimple over time.   Figure 16. Cavitation developed rapidly during t = 0-0.01 s, and the gas mass generation rate reached the maximum at t = 0.003 s. Then, the gas mass generation rate gradually decreased, and the gas mass disappearance rate remained basically unchanged. Simultaneously, the generation of the gas phase was accompanied by a disappearance; that is, the collapse of the cavitation bubble was accompanied by cavitation generation, and the peak value of the disappearance rate of the gas phase was smaller than the generation rate, so the cavitation area gradually increased with time.

Experimental Facilities
In order to further analyze the cavitation phenomena between rotating friction pairs, we processed a separator disk with a texture ratio of 6% using a laser marking machine ( Figure 18). Our research team has extensive experience in building friction test rigs [43]. We set up a visual transparent testbed, which included a transparent host, hydraulic system, and data acquisition system. The transparent host is the main object of power input and output, which is mainly composed of a frequency converter, a three-phase asynchronous motor, and a host. We can observe oil film morphology through it. As is shown in Figure 19, the motor speed is controlled by the frequency converter to adjust the input speed, and the evolution process of cavitation morphology is mainly filmed using a high-speed camera. The fill light illuminates the host directly to measure the driven plate, and the light source is added to obtain the clear flow field motion pattern. Figure 19. Transparent test platform (1 = high-speed camera; 2 = lens; 3 = computer; 4 = fill light; 5 = host; 6 = motor; 7 = data collection unit; 8 = magnet powder brake; 9 = torque sensor; 10 = coupling; 11 = base).

Experimental Results
In our experiment, we first selected the non-texture friction disk as the object, and the motor speed was adjusted to 350 rpm, 550 rpm, and 1050 rpm using the frequency converter. The flow field morphology is shown in Figure 20. It can be seen that although the speed increased, the oil film remained intact during the whole test cycle, and there were no cavitation bubbles. Therefore, the pressure pulsation of texture dimples is considered to be an important factor of cavitation. It should be noted that a few linear highlighted areas along the radial direction in the figure were scratches left by transparent box processing. In the next experiment, when the shot angle was adjusted, the linear highlighting area was no longer present. Then, we repeated the experiment with a textured disk ( Figure 21). When the rotation speed was 350 rpm, the oil film remained intact and no cavitation phenomenon occurred. When the speed was increased to 550 rpm, the circumferential velocity increased, and cavitation happened obviously. Due to the joint action of wall adsorption and oil film shear, the two "Bubble" areas appeared as narrow arcs. When the rotation speed increased to 1050 rpm, compared with 550 rpm, the bubble sizes increased, and the number of narrow bubbles increased. The cavitation area at the outer diameter increased and gradually moved in the inner diameter's direction. It can be seen in Figure 21 that there were obvious cavitation bubbles when the rotation speed was 550 rpm. In order to conduct a more detailed study, high-speed cameras were used to catch cavitation morphology. We took 3218 photos in total. We took the time from a single cavitation bubble's debut to its regeneration to be period T. We focused on a single bubble and observed a total of 46 photos in T. The cavitation evolution pattern is shown in Figure 22. As is shown in Figure 22, when t = 1/46 T, the cavitation bubble looks like a sheet with a fixed and obvious boundary attached to the disk surface in a long and narrow arc shape. The cavitation bubble was very thin. From t = 1/46 T to 35/46 T, the cavitation bubble moved clockwise along the oil flow direction and got closer to the outer diameter. In the free state, the cavitation bubble grew bigger and longer. When t = 35/46 T, the cavitation bubble reached its maximum spanwise width (spanwise is the direction perpendicular to the incoming flow direction and parallel to the surface of the disk). When t = 39/46 T, the bubble's oncoming surface burst first, possibly because the bubble entered into negative pressure gradient region and squeezed the oncoming surface first. Simultaneously, the front end of the cavitation bubble started to fall off from the initial sheet cavitation into tiny bubbles in a process called cloud cavitation. The cavitation bubble split into a front-end cloud cavitation and a back-end sheet cavitation and started to collapse. From t = 39/46 T to 43/46 T, the cavitation morphology changed from sheet cavitation to cloud cavitation along the front to back end, and the bubble's boundary became totally fuzzy. The spanwise width reached its maximum, and the cavitation bubble completely changed from sheet cavitation to cloud cavitation and free bubble cavitation. At t = 46/46 T, the cavitation bubble disappeared. The cavitation collapse is extremely rapid, accounting for 7/46 of the cycle of a single cavitation bubble. However, this time ratio is still very high. The possible reason is that the viscosity of the hydraulic oil used in the test slows down the collapse rate.
When the rotational speed was 550 rpm, another larger cavitation bubble was selected for monitoring. According to our test results, 83 photos of this cavitation bubble survived in our view, as shown in Figure 23. In contrast to Figure 22, the larger bubble did not completely collapse during the cycle. The cavitation bubble expanded to the maximum width and then decreased, and finally moved out of the monitoring window. In Figure 23, when t = 1/83 T, the bubble was just coming into view. From t = 1/83 T to t = 30/83 T, the integral shape of the cavitation bubble appeared in the monitoring window and moved to the outer diameter gradually. The bubble's length was close to the characteristic length of the friction disk, so this can be defined as supercavitation. When t = 40/83 T, the supercavitation bubble reached its maximum size and burst into numerous small bubbles at the front. From t = 40/83 T to t = 71/83 T, the cavitation bubble gradually moved to the outer diameter and fell off, and a new generation bubble appeared at t = 80/83 T. Compared with Figure 22, it can be seen that the bubbles of large structures can survive longer and are less prone to collapse than those of small structures.
At 1050 rpm, the cavitation was more intense, and the survival law of a single cavitation bubble was similar to that shown in Figures 22 and 23, so it will not be repeated. Figure 24 shows that cavitation occurred periodically, and the oil film shrunk. The oil film shrink expanded to the outer diameter and was accompanied by the debut and growth of fresh cavitation. When the cavitation collapsed, a new round of oil film shrinkage occurred. In particular, a gas-liquid two-phase flow region was generated at the outer diameter of the textured disk.

Conclusions
In this study, first, the governing equations and models used in the simulation analysis are discussed, including the homogeneous flow model, turbulence model, and cavitation model. Second, a flow field model was established to analyze the cavitation morphology of a 3D textured surface. The cavitation law was analyzed from the perspectives of pressure distribution, cavitation gas fraction, and gas-liquid mass transfer, simultaneously. Third a transparent test device was built to capture the cavitation morphology, and it was found that the photos taken during the experiment were consistent with the simulation results. The research results can be applied to the optimal design of mechanical seals and wet clutches, and after extension, can be further applied to internal combustion engine cylinders and bionics equipment. It can improve the sliding performance and weaken the cavitation effect in practical applications.
By analyzing the cavitation flow field, the pressure in the cavitation region is always found to be lower than the saturated steam pressure. By comparing the velocity vector arrows of the two-phase flow, it was found that the motion directions of the liquid phase and vapor phase are consistent, and there is mass transfer between the two phases, so it is verified that cavitation bubbles originate from the phase transition. At the same time, cavitation debut and collapse exist simultaneously, and cavitation generation is faster than cavitation collapse, so the cavitation area expands.
In application scenarios requiring high bearing capacities and low torque, such as mechanical seals, the treatment of the end texture is already a mature technology. The cavitation sum caused by texture is not proportional to the texture ratio. Therefore, it is worth analyzing the optimal texture ratio in future research to provide guidance for engineering projects. It was also found that cavitation was more likely to occur at the outer diameter of the rotating disk, i.e., the region of higher radial velocity. Therefore, in order to obtain the beneficial effect of the texture structure, it is possible to consider processing the micro-texture in the range of the inner diameter region.
Low pressure and cavitation core are the most influential factors. This study verifies that uneven surfaces of machinery equipment are key inducers of cavitation, we used nontexture friction pair as a reference experiment, and the simulation analysis and experimental study both verify that smooth surfaces do not generate cavitation. The surface of the textured friction pair shows a severe cavitation phenomenon. Therefore, more attention should be paid to surface roughness when machining micro-textures. Cavitation is more likely to occur at high rotational speeds.

Patents
The patent number is CN201810435987.8.

Data Availability Statement:
The data that support the findings in this study are available from the author J.S. upon reasonable request.
Acknowledgments: In addition to the efforts of the co-authors, I need to thank the School of Mechanical Engineering of Jiangsu University for providing the experimental apparatus and experimental materials. As well as colleagues from the Institute of Mechatronic and Hydraulic Control for their help in the experiments.

Conflicts of Interest:
The authors declare no conflicts of interest.