Development of Various Types of Independent Phase Based Pulsewidth Modulation Techniques for Three ‐ Phase Voltage Source Inverters

: Discontinuous pulse ‐ width ‐ modulation (DPWM) methods have been extensively used in the industrial area to reduce overall losses, which decreases the corresponding thermal stress on the power switches of converters. However, local thermal overload can arise due to different aging con ‐ ditions of semiconductor devices or failure in the cooling system. This leads to reduced reliability of the converter system due to the low expected lifespan of the most aged switches or phase legs. In this paper, the modified DPWM strategies for independent control of per ‐ phase switching loss are introduced to deal with this matter. The proposed per ‐ phase DPWM techniques are generated by modifying the conventional three ‐ phase DPWM methods for reducing the switching loss in a spe ‐ cific leg, whereas the output performance is not degraded. This paper reports on output perfor ‐ mance, including output current total harmonic distortion (THD) and power loss of switching de ‐ vices, analysis for the various modified DPWM strategies for independent control of per ‐ phase switching loss, which is applicable in 2 ‐ level 3 ‐ phase voltage source inverters (2L3P VSIs). The re ‐ sults are compared to the corresponding continuous PWM technique to verify and analyze the ef ‐ fectiveness and accuracy of the modified DPWM strategies for independent control of per ‐ phase switching loss.


Introduction
The increasing number of power electronics applications in industry, consumer electronics, and transportation emphasizes the rising significance of power converters in the power system.Their importance becomes evident in their role in offering grid services.However, there is potential for improvement in converter reliability as costly failures and system downtime are associated with them [1][2][3].Due to the discovery that power semiconductor devices within power modules experience frequent failures [4,5], significant efforts have been dedicated to enhancing the expected lifespan of these components.Semiconductor manufacturers optimize the hardware to increase reliability, but it also sharply raises the cost of devices.The reliability of power modules is closely linked to thermal stress, as evidenced by the correlation between thermal cycles and lifespan, demonstrated in [6], which has been corroborated by several follow-up studies [3,7].Therefore, various control strategies which aim at increasing the reliability of power converters by controlling thermal stress are extensively developed [8][9][10][11][12].Among developed solutions, the decrease of switching loss is extensively used because the switching loss of the power switch is predominantly impacted by switching frequency.The research presented in [13,14] proposed regulating the switching frequency as a means to relieve thermal stress.However, this approach leads to an undesired fluctuation in the output current spectrum, making it unsuitable for many applications.Typically, the DPWM is employed to minimize switching losses by clamping the output voltage at either the positive or negative dc-link voltage [15,16].This leads to a significant decrease in losses when compared to continuous PWM since the power semiconductors remain unswitched during the clamping intervals.However, the clamping behavior leads to an increase in the THD of the output currents, necessitating a larger output filter or a higher switching frequency.
Under ideal operating conditions, the three-phase converters can achieve a similar aging condition in each phase leg.However, in practical operating conditions, within the three-phase converter, individual phase legs may exhibit diverse aging conditions or expected lifespan arising from uneven stress during operation or prior replacement of power switches.Furthermore, manufacturing techniques have been recognized as a potential origin of power semiconductor device failures [17].However, the active thermal control methods mentioned earlier do not take into consideration the case that the converter legs could undergo differing aging conditions despite efforts to enhance the converter's overall reliability.Another approach to managing switching losses at the device level involves existing gate control.The relationship between the gate voltage, resistor, and the lifespan of power devices has been established through a precise field mission profile [18].The gate control does not impact the converter's output current ripple, but it necessitates an additional circuit, which increases the system's complexity.The gate drive voltage has an impact on saturation voltage and switching loss, allowing for the regulation of power device losses.When the operating temperature of power transistors increases, their on-state resistance and power losses increase as well.To mitigate this, it is recommended to increase the amplitude of the applied driving level [19].Nevertheless, the precise control of voltage levels required for this technique makes it impractical.In addition, the author in [20] proposes a voltage and current control scheme for a 2-level 4wire converter that aims at controlling phase output power depending on its aging condition.Nevertheless, this approach has its constraints because of the converter's design.The author in [21] proposes a hybrid offset approach to control the phase switching frequency following the aging degree.Since the output current is directly used to identify the clamping areas, this method is only effective when the power factor is close to unity where the output voltage and current are in phase.An approach based on modifying the DPWM for individual loss reduction for each phase of the voltage source rectifier is proposed in [22].However, this study only considers a single case of the DPWM technique for per-phase control, which cannot give a comprehensive study about per-phase DPWM techniques.Hence, it is essential to implement various per-phase control strategies that focus on minimizing switching losses to prolong the lifespan of a specific phase within the inverter.
In this paper, the modified DPWM strategies for independent control of per-phase switching loss, aimed at delaying the failure of the most aged phase leg to extend the lifespan of the entire converter, are proposed.Different from conventional three-phase DPWM techniques, the per-phase DPWM strategies generate clamping regions for only the most aged phase leg, whereas the two remaining phase legs are operated as in continuous PWM.This led to an increase in the lifetime of the most aged leg but avoided degrading the output performance of the converter too much.The simulation and experimental results are explored by implementing various modified per-phase DPWM strategies in a 2L3P VSI.In Section 2 of this paper, an initial overview is provided concerning the 2L3P VSI and the principle of previous three-phase DPWM strategies.In Section 3, the modified DPWM strategies for independent control of per-phase switching loss are presented.The subsequent Section, Section 4, outlines an evaluation conducted through simulation, accompanied by the inclusion of experimental findings.The final Section offers a summarization of the developed comparative assessment of the various modified perphase DPWM techniques proposed in this study.

Three-Phase DPWM Techniques
The typical configuration of a 2L3P VSI is shown in Figure 1. stands for the dclink voltage, and  represents a virtual neutral point of the dc-link. and   , ,  indicate the switching patterns for upper and lower switches in each phase, respectively.  , ,  stands for phase output currents.The three pole-voltage references or modulation voltages of three-phase VSI,   , ,  , can be defined as: where   , ,  is the phase reference voltage and  is the zero-sequence voltage signal.The zero-sequence voltage  corresponds to the voltage difference between the neutral point of load and the midpoint of dc-link [23,24].When  0, it yields sinusoidal PWM.
The modulation voltage   , ,  are physically limited by the dc-link voltage  as: In the linear modulation range, the modulation voltages are physically limited as shown in equation (2).Hence, from equations ( 1) and ( 2), the condition of zero-sequence voltage can be yielded as follows [24]:  (3).The use of an injected zero-sequence voltage signal for a three-phase inverter initiated the research on non-sinusoidal carrier-based PWM.Different zero-sequence signals lead to different non-sinusoidal PWM modulators and different advantages, such as lower harmonic currents, higher available modulation index, or switching loss reduction compared to the sinusoidal PWM.
Here, the various conventional three-phase DPWM approaches will be introduced based on a PWM scheme.Following previous knowledge [24,25], it is common that introducing an identical zero-sequence voltage to the voltage references of the inverter does not alter the fundamental voltages delivered to the load.Thanks to this characteristic, various DPWM strategies have been previously proposed with the goal of diminishing  Figure 3 illustrates the reference voltage signal, modulation voltage, and zero-sequence voltage signal waveforms in phase  of six common DPWM strategies.DPWMx (x = 0,1,2,3) consists of clamping the upper switch and lower switch for alternatively, respectively, 60 within a fundamental period.The clamping intervals are distributed symmetrically.Among the DPWMx (x = 0,1,2,3) strategies, the DPWM1 scheme generates clamping intervals at peaks of reference voltages [26].Meanwhile, the DPWM0 and DPWM2 approaches have the clamping phase-shifted by 30 and 30 with respect to DPWM1, respectively [27,28].It will be observed that it is possible to provide other intermediate placements of saturations to favor certain operating points.The DPWM3 divides the clamping interval of 120 into four intervals, each spanning 30 [27].In the DPWMMAX, only the upper switch in the phase leg of the inverter remains in a high state for the clamping interval of 120 in the fundamental period [27], while only the lower switches in the phase leg of the inverter maintain the high state for the same duration in the DPWMMIN [29].Furthermore, the DPWM1 positions the center of each clamping interval in alignment with the peak of the reference voltage, rendering it appropriate for applications requiring a unity power factor.The DPWM0 and DPWM2 prove effective for power factors with a 30 leading and lagging phase, respectively.In contrast, the DPWM3 can find utility in reactive power compensation applications.A generalized relation that enables constructing the zero-sequence voltage signal as a function of ,  and  is expressed as follows: In equation ( 4)  can take any form (constant or time-varying) ranging between zero and unity [24,25].The DPWMx is obtained when  1 0.5 1  3   and varying the modulation angle  .When  0.5 , the zero-sequence voltage  0.5   , results in the continuous modulation, named SVPWM.The zero-sequence voltage of DPWMMAX is determined by the maximum value among three reference voltages, resulting in   , which is equivalent to  0. If  1, the DPWM-MIN is obtained.The zero-sequence voltage of the DPWMMIN is determined by the maximum value among three reference voltages, resulting in   .It is important to recognize that employing the DPWMMIN or DPWMMAX leads to an imbalanced allocation of switching loss and thermal stress between the upper and lower switching devices.Certainly, under the DPWMMAX approach, the upper switch has a lower switching loss than the lower one, whereas it is the opposite of the DPWMMIN technique.Table 1 summarizes the different types of DPWM following the values of .In Table 1,  defines the load angle, which is the phase angle between voltage and current caused by the load condition.  SVPWM 0.5 x DPWM0 1 0.5 1  3    30 In previous conventional DPWM, the current is disregarded, resulting in a fixed pattern of modulation that is chosen based on its application.To increase the efficiency of the DPWM methods, a generalized DPWM (GDPWM) is proposed in [30].The GDPWM detects the magnitude of phase output current relative to the inverter reference voltage and determines the optimum clamping interval instantaneously.Variable clamping intervals can be achieved based on the magnitude of the phase current.

Per-Phase DPWM Technique for Independent Control of Switching Loss
As previously discussed, the aging state among phase legs of converter might be different attributed to reasons like the manufacturing procedure, uneven distribution of thermal stress, and prior replacements.Consequently, the remaining useful lifespan of phase leg is not similar to each other.The converter would cease operation in the event of malfunction in any one leg, it becomes essential to extend lifespan of the most aged leg.A fundamental concept for extending the lifespan of the most aged leg involves lowering their switching loss.However, a reduction in switching frequency will lower the output performance of the VSIs.Furthermore, improperly decreasing the switching frequency of a specific phase within the VSI will lead to a degradation in the output currents.Therefore, lowering the switching frequency of specific legs using a modified modulation strategy is the most suitable solution without degrading the output performance and any additional circuits or equipment.Therefore, in this study, the DPWM strategies will be modified to precisely manage the switching frequency of specific phase legs in 2L3P VSI.As for the proposed per-phase DPWM strategies, it requires determining the most aged phase leg.The diagnosis methods require the aging indicator to identify the current aging status of the power semiconductor devices.The aging indicator identification on the power semiconductor device has been carried out by performing an accelerated aging experiment with monitoring of selected parameters.Accelerated aging tests allow the effects of failure mechanisms to be analyzed and aging indicators to be identified.Various electrical aging indicators for the IGBT have been investigated and proposed in the literature such as changes in temperature, component transconductance, collector-emitter on-state voltage  , , and threshold voltage  .However, the diagnosis method is out of scope of this study, a detailed description is not included.To control the switching frequency of a specific leg, phase  is considered as an example; the possible clamping interval can be determined, as depicted in Figure 5.The reference voltage of phase  includes two parts, including possible clamping interval and impossible clamping interval, corresponding to the cases that    and    , respectively.As indicated earlier, it is common that introducing an identical zero-sequence voltage to the voltage references of the inverter does not alter the fundamental voltages delivered to the load.Hence, to avoid compromising the output current quality but reducing the switching frequency of specific phase, the calculation of zero-sequence voltage will be adjusted based on the possible clamping and impossible clamping intervals as follows: where  _ indicates the zero-sequence voltage at the possible clamping interval, whereas  _ indicates the zero-sequence voltage at the impossible clamping interval.To guarantee the output performance and avoid deteriorating the output currents waveform at the possible clamping interval,  _ is injected into both three phases voltage references.Meanwhile, at impossible clamping intervals,  _ , which is calculated as in the SVPWM method, is injected.The flowchart of zero-sequence voltage generation in the modified DPWM for independent control of per-phase switching loss is presented in Figure 6.Determine maximum reference voltage V max and minimum reference voltage In addition to the modified DPWM strategies, the GDPWM can also be modified for independent control of per-phase switching loss.The same principle as in the modified DPWM strategies is applied to the GDPWM.The flowchart of zero-sequence voltage generation in the modified GDPWM for independent control of per-phase switching loss is depicted in Figure 8a.The zero-sequence voltage is determined by evaluating the absolute value of  and  , where  min  ,  ,  and  max  ,  ,  at the clamping interval.Figure 8b

Verification and Evaluation Results
The performance of different DPWM strategies for independent control of per-phase switching loss is validated using simulation and experiment findings.The performance comparison among the per-phase DPWM control schemes concerning the loss calculation is acquired by employing a thermal module in the PSIM software.To ensure the power loss calculation is correct, the model of power switches is selected from the device library in PSIM, whereas the device's information from manufacturer's datasheet is added into corresponding device.The 2L3P VSI has listed parameters in Table 2. Figure 9 depicts the block diagram of a closed-loop current control-based proportional-integral (PI) controller for 2L3P VSI.The use of a PI controller is favored due to its simplicity and ease of implementation when contrasted with more advanced controllers.The inherent stability of the PI controller makes it less susceptible to oscillations than its advanced ones.Moreover, tuning the gains of a PI controller is generally straightforward, while more complex controllers may involve adjusting additional parameters that require careful attention.The value of PI gains is listed in Table 2.The phase voltage reference signals are generated by the PI controller, whereas different zero-sequence voltage signals corresponding to different per-phase DPWM strategies are generated using schemes shown in Figures 6 and 8.

Determine maximum reference voltage V max and minimum reference voltage V min
Assign maximum current i max and minimum current i min associated with V max and V min Read the generated reference voltage v refa , v refa, v refa and measured output current i oa , i ob , i oc Yes  The simulation of a 2L3P VSI is implemented in the PSIM software environment.The simulation results of output currents, modulation voltage, zero-sequence voltage, and switching patterns obtained by the various per-phase DPWM strategies for independent control of per-phase switching loss are shown in Figure 10.The output currents obtained by the various per-phase DPWM strategies have sinusoidal waveform and accurate magnitude and phase.The switching pattern of phase   generated by various per-phase DPWM strategies has the clamping interval, which relates to the clamping interval of phase  modulation voltage.Meanwhile, the switching pattern of phase   and   do not include clamping interval due to the corresponding modulation voltages do not clamp at  2 ⁄ .As shown in Figure 10g, the per-phase GDPWM strategy generates the clamping interval corresponding to the interval that phase  output current has the highest absolute value as expected.Due to the load angle  20 , the per-phase GDPWM is quite similar to the per-phase DPWM2 strategy.The output current THD percentages obtained by various per-phase DPWM strategies are shown in Figure 11a.The output performance of continuous modulation, i.e., the SVPWM method, is considered a reference object for comparison.As observed in Figure 11a, the SVPWM method has the lowest phase  and the average THD percentage at 0.73%.The clamping interval or unmodulated period in the per-phase DPWM strategies results in poorer output current quality, e.g., higher THD percentage.The phase  output current THD obtained by the per-phase DPWMx (x = 0,1,2,3) and per-phase GDPWM strategies are about 42% higher than that of the SVPWM scheme, while the average output current THD acquired by these per-phase DPWM strategies is about 26% higher than the SVPWM scheme.It is noticeable that from Figure 11b, the per-phase DPWM strategies decrease switching frequency in phase  by approximately 33% compared to the SVPWM method.The power loss of phase , including switching and conduction losses, and total loss of VSI are presented in Figure 11c,d, respectively.In terms of power loss in phase , the conduction loss slightly increases in per-phase DPWM strategies due to the clamping interval compared to SVPWM.In Figure 11c, the switching loss reduction in the various per-phase DPWM strategies is different due to the different positions of the clamping interval.Looking at Figure 11c in more detail, per-phase DPWM2 and per-phase GDPWM strategies have the same reduction of switching loss at about 47% compared to the switching loss of the SVPWM.Meanwhile, the switching loss of the per-phase DPWM1 and per-phase DPWM3 strategies are less reduced than other the per-phase DPWM strategies at about 32%.The chart in Figure 11d shows the total loss of the VSI resulting from the different per-phase DPWM strategies.As observed in Figure 11d, it is noticeable that the reduction of total loss obtained by various per-phase DPWM strategies is smaller than that of phase  switching loss in Figure 12c.This is due to the two remaining phase legs , and  are kept continuously operating at a predefined switching frequency as in the SVPWM method, resulting in similar switching loss and conduction loss in phases  and .The total loss reduction obtained by the per-phase DPWM strategies is slight, ranging from 6.7% to 9.2% compared to the SVPWM method.As for efficiency, the difference among approaches is negligible.The performance of 2L3P VSI, implemented at another load angle  75 , is shown in Figure 12.Because the phase difference between phase output current and phase output voltage increases along with the rise of load angle, the performance of various perphase DPWM strategies will change remarkably.As observed in Figure 12a, the output current THD percentage in phase  and average value of SVPWM is the lowest at 0.39%.The phase  output current THD percentage of the per-phase DPWM0 is the highest at 0.86%, which increases by 120% compared to the SVPWM.Regarding the average output current THD, the per-phase DPWM2 strategy has the highest at 0.74%, which increases by about 90% compared to the SVPWM.In terms of switching frequency, due to the same magnitude of the clamping interval, the reduction acquired by the per-phase DPWM strategies is similar to the previous load angle  20 .It can be noticed from Figure 12c that the reduction of switching loss acquired by various per-phase DPWM strategies is lower than load angle  20 .The phase  switching loss of the per-phase GDPWM schemes decreases by about 37.5%, compared to the SVPWM method.Meanwhile, the decrease in switching loss acquired by remaining the per-phase DPWM strategies ranges from 18% to 37%.Regarding the total loss of VSI, the per-phase DPWM2 and per-phase GDPWM schemes have the lowest loss, which is about 7.5% lower than that of the SVPWM method.Hence, it can be concluded that the increase in load angle weakens the effect of the per-phase DPWM strategies in terms of switching loss reduction.As for efficiency, the difference among approaches is negligible.

THD (%)
Phase a Average value Output current THD  Figure 13 presents a performance comparison among the per-phase DPWM strategies at variation of carrier frequency.The SVPWM has the highest switching frequency, and the remaining per-phase DPWM strategies exhibit the same switching frequency.Because of continuous modulation, the SVPWM exhibits the lowest average output current THD under variation of carrier frequency.In terms of power loss, the conduction loss of phase  obtained by the per-phase DPWM strategies is similar under variation of carrier frequency.Meanwhile, the per-phase GDPWM has the lowest switching and total losses under variation of carrier frequency thanks to the clamping interval corresponding to the interval that magnitude of conducted current is the largest.Figure 14 presents a performance comparison among the per-phase DPWM strategies at variation of modulation index.As presented, the switching frequency in different control schemes does not change under variation of modulation index.Due to continuous modulation, SVPWM has the lowest average output current THD under variation of modulation index.In terms of power loss, both conduction and switching losses increase following the rise of modulation index.The conduction loss of phase  acquired by different approaches are similar.Meanwhile, the per-phase GDPWM has the lowest switching and total losses under variation of modulation index thanks to the clamping interval is corresponding to the interval that magnitude of conducted current is the largest.Figure 15 presents a performance comparison among per-phase DPWM strategies at variation of load angle.As presented, the switching frequency in different control schemes does not change under variation of load angle.Due to continuous modulation, the SVPWM has the lowest average output current THD under variation of load angle.As can be seen, the output current THD decreases when the load angle increase.In terms of power loss, conduction loss in phase  decreases along with the rise of load angle.Meanwhile, the switching loss in phase  increase when the load angle increase.It validates that the increase of load angle reduces the effect of the per-phase DPWM strategies.Meanwhile, the per-phase GDPWM has the lowest switching and total losses under variation of load angle thanks to the clamping interval is corresponding to the interval that magnitude of conducted current is the largest.The per-phase DPWM strategies are also verified and implemented in the laboratory on an experimental setup of the 2L3P VSI connected to a three-phase   load, as displayed in Figure 16.The experiment is conducted using the identical parameters outlined in Table 2.The control schemes are applied and run using a Texas Instrument TMS320F28335 digital signal processor (DSP).In the experiment, the THD of output currents are measured by using waveform inspector function in MSO3054 Oscilloscope from Tektronix.Figure 19 presents the measured THD of each per-phase DPWM strategy against the THD given by the SVPWM.As can be seen in Figure 19, due to being the CPWM, the SVPWM has the lowest THD value, whereas the per-phase DPWM3 has the highest THD.For further verification, the proposed per-phase DPWM strategies are employed under unbalanced load condition.It should be noted that the 2L3P VSI does not have the flow path for the zero-sequence current of the unbalanced load, this results in unbalanced output currents when implementing the proposed per-phase DPWM approaches.However, these proposed per-phase DPWM approaches do not require information of load, thus, the generation of clamping interval in each per-phase DPWM is guaranteed.As can be seen in Figure 20

Conclusions
This paper explores the output performance, including output current THD and power loss of switching devices, of the various modified DPWM strategies for independent control of per-phase switching loss, which are applicable in 2L3P VSIs.From the simulation and experimental result, it can be concluded that the per-phase DPWM strategies can precisely manage the switching frequency and switching loss of specific legs in 2L3P VSI.Thanks to the clamping interval, which is always located at the peak absolute value of output current, per-phase GDPWM is the most effective way to decrease the switching loss of specific phase legs, though it slightly increases the output current THD percentage.However, it requires knowing the instantaneous magnitude of phase output currents.The remaining per-phase DPWM strategies, including the DPWMx (x = 0,1,2,3) per-phase, the per-phase DPWMMIN, and the per-phase DPWMMAX strategies, prettily decrease the switching loss but are not stable, where the performance of these techniques is dependent on the load power factors and applications.Additionally, the increase in load angle weakens the effect of per-phase DPWM strategies in terms of switching loss reduction.The trade-off-between reducing loss and deterioration of the harmonic of the output current may reduce efficiency in electrical loads, particularly inductive loads like electric motor.This can be resolved by using a passive filter to attenuate specific harmonics or designing an active power filter to cancel out the undesired harmonics.This work will be considered in future research.

Figure 2
depicts the general control diagram of VSI using a carrier-based PWM (CBPWM) scheme, where three modulation voltages   , ,  are compared to one triangular carrier to generate the switching patterns   , ,  .

Figure 2 .
Figure 2. General control diagram of VSI using CBPWM.Based on the zero-sequence voltage  and modulation voltage   , ,  , PWM strategies are divided into two categories as follows: the continuous PWM (CPWM) and DPWM.The CPWM maintains modulation voltages without clamping throughout a cycle of the fundamental voltage, except for instances of overmodulation.Two widely recognized CPWM techniques are the sinusoidal PWM (SPWM) and space vector PWM (SVPWM) [24].On the other hand, in DPWM, modulation voltages contain clamping interval that equals onethird of the fundamental period.The switching state is kept unchanged during the clamping interval.Consequently, the switching frequency of the VSI is lowered, leading to a reduction in the corresponding switching losses.Various three-phase DPWM techniques have been investigated in this Section based on the positioning of the clamping interval.Figure3illustrates the reference voltage signal, modulation voltage, and zero-sequence voltage signal waveforms in phase  of six common DPWM strategies.DPWMx (x = 0,1,2,3) consists of clamping the upper switch and lower switch for alternatively, respectively, 60 within a fundamental period.The clamping intervals are distributed symmetrically.Among the DPWMx (x = 0,1,2,3) strategies, the DPWM1 scheme generates clamping intervals at peaks of reference voltages[26].Meanwhile, the DPWM0 and DPWM2 approaches have the clamping phase-shifted by 30 and 30 with respect to DPWM1, respectively[27,28].It will be observed that it is possible to provide other intermediate placements of saturations to favor certain operating points.The DPWM3 divides the clamping interval of 120 into four intervals, each spanning 30[27].In the DPWMMAX, only the upper switch in the phase leg of the inverter remains in a high state for the clamping interval of 120 in the fundamental period[27], while only the lower switches in the phase leg of the inverter maintain the high state for the same duration in the DPWMMIN[29].Furthermore, the DPWM1 positions the center of each clamping interval in alignment with the peak of the reference voltage, rendering it appropriate for applications requiring a unity power factor.The DPWM0 and DPWM2 prove effective for power factors with a 30 leading and lagging phase, respectively.In contrast, the DPWM3 can find utility in reactive power compensation applications.
Figure 4 depicts the zerosequence voltage signal, modulation voltage signals, and phase output current waveforms obtained by the GDPWM with load angle  20 and  70 .The clamping intervals follow the peak of corresponding phase currents and are different between two cases of load angle.

Figure 4 .
Figure 4. Modulation voltages, zero-sequence voltage signal waveforms, and phase output current waveforms obtained by GDPWM with (a) load angle  20 , (b) load angle  70

Figure 6 .
Figure 6.Flowchart of zero-sequence voltage generation in modified DPWM for independent control of per-phase switching loss.

Figure 7
Figure7shows the zero-sequence voltage signal, modulation voltages, and corresponding switching pattern obtained by various per-phase DPWM methods  200 V, load angle  20 .Assuming that phase  is the most aged leg.In Figure7, the injected zero-sequence voltage signal generated the clamping intervals at  2 ⁄ in phase  modulation voltage, which results that switching pattern  keeps current state during the clamping period.Meanwhile, phase  and  modulation voltages do not clamp, which results that the switching patterns  and  continuously change their status.Additionally, the zero-sequence voltage signal is different from the previous one in the standard DPWM strategies.As observed in Figure7, the clamping interval of phase  modulation voltage is equivalent to the standard three-phase DPWM strategies shown in Figure3, whereas the non-clamping interval of phase  modulation voltages is equivalent to the standard SVPWM strategy.

Figure 8 .
Figure 8.(a) Flowchart of zero-sequence voltage generation in modified GDPWM for independent control of per-phase switching loss, (b) Output currents, zero-sequence voltage signal, modulation voltages, and corresponding switching patterns waveforms obtained by per-phase GDPWM  200 V, load angle  20 .

Figure 9 .
Figure 9. Block control diagram of per-phase DPWM methods based PI controller.

Figure 12 .
Figure 12.Comparison results of conventional SVPWM and various per-phase DPWM strategies (a) Average output current THD, (b) Switching frequency of phase , (c) Power loss in phase , (d) Total loss, (e) Efficiency. 200 V, modulation index 0.42, load angle  75 .

Figure 13 .
Figure 13.Comparison results of the conventional SVPWM and various per-phase DPWM strategies under variation of carrier frequency (a) Switching frequency of phase , (b) Average switching frequency, (c) Average output current THD, (d) Conduction loss in phase ,(e) Switching loss in phase , (f) Total loss. 200 V, carrier frequency  10 kHz, load angle  20 .

Figure 14 .
Figure 14.Comparison results of the conventional SVPWM and various per-phase DPWM strategies under variation of modulation index (a) Switching frequency of phase , (b) Average switching frequency, (c) Average output current THD, (d) Conduction loss in phase ,(e) Switching loss in phase , (f) Total loss. 200 V, carrier frequency  10 kHz, load angle  20 .

Figure 15 .
Figure 15.Comparison results of the conventional SVPWM and various per-phase DPWM strategies under variation of load angle (a) Switching frequency of phase , (b) Average switching frequency, (c) Average output current THD, (d) Conduction loss in phase ,(e) Switching loss in phase , (f) Total loss. 200 V, carrier frequency  10 kHz, load angle  20 .

Figure 16 .
Figure 16.Experimental configuration of 2L3P VSI and control stage.

Figure 17
Figure 17 depicts the experimental results of output current waveforms, phase  modulation voltage, and zero-sequence voltage signal obtained by different per-phase DPWM strategies.It can be seen that all per-phase DPWM strategies generate sinusoidal output currents.The waveform of phase  modulation voltage and zero-sequence voltage signal acquired by the different per-phase DPWM strategies is matched to the simulation waveforms.Figure 18 presents the experimental waveforms of output current waveforms, modulation voltage, and switching pattern of phase  obtained by different per-phase DPWM strategies.As observed in Figure 18, phase  switching state is kept at a high state or low state, correctly corresponding to the clamping interval of the modulation voltage.The experiment results present identical waveforms as in the simulation Section, which verifies the correctness and effectiveness of the per-phase DPWM strategies.

Figure 17 .Figure 18 .
Figure 17.The experimental waveforms of output currents, phase  modulation voltage, and zerosequence voltage signal obtained by different per-phase DPWM strategies (a) Per-phase DPWM0,

Figure 19 .
Figure 19.Comparison results of conventional SVPWM and various per-phase DPWM strategies in terms of output current THD obtained from experimental results.
, the output currents obtained by the per-phase DPWM strategies are sinusoidal and correct in terms of magnitude following the difference in load resistance.Meanwhile, the switching pattern of phase   generated by various per-phase DPWM strategies has the clamping interval, which relates to the clamping interval of phase  modulation voltage.Meanwhile, the switching pattern of phase   and   do not include clamping interval due to the corresponding modulation voltages do not clamp at  2 ⁄ .It verifies that the proposed per-phase DPWM strategies operate correctly under unbalanced load conditions.