Feasibility of Recycling Ultrafine Leaching Residue by Backfill : Experimental and CFD Approaches

Large amounts of leaching residue are released into tailings dams from mines, and their acid content can cause environmental pollution. The aim of this study was to research the feasibility and value of a leaching residue backfill recycling method. The combination of property detection, laboratory tests (the neutralization method, strength test and diffusivity test) and numerical simulation methods (3D computational fluid dynamics (CFD) simulations of pipeline transportation properties) were used to assess the performance of the leaching residue backfill. The results show that backfill body with the cement:sand mass ratio of 1:3, the leaching residue:classified tailings ratio of 1:6, and slurry mass concentration of 71 wt % can meet the strength and pipeline self-flowing transportation requirements of mine backfill. The leaching residue is a good backfill aggregate, and its recovery ratio can reach 19.5 wt %. In addition, the recycling of leaching residue effectively alleviates the problem of mine waste emissions and protects the ecological environment surrounding the mining area. This study serves as a guide for the recycling of fine tailings and the environmental governance of the mining area.


Introduction
The processing and management of mine tailings has been receiving more and more attention around the world [1,2].As the main solid waste of mines, most of the tailings are stored in tailings dams and are hard to recycled.Many large tailings dams have to be built to contain mining waste [3,4].However, they are often accompanied by many types of hazards, and the harm of waste tailings to the environment, the safety of lives and property is very significant [5][6][7][8].In order to address those issues that mine tailings entail, some mining researchers proposed the backfill method to improve the recovery of the tailings.Furthermore, the paste backfill technology has been widely used all over the world for mine tailings treatment [9,10].As pointed out by Edraki et al. [11] and Benzaazoua et al. [12], the mine backfill is an effective method to dispose of the tailings.
The Fan Kou lead-zinc mine, located in the northeastern Guangdong Province of China, outputs 1.4 million tons of ore per year.Also, more and more advanced technologies are used to increase the extraction rate of minerals by grinding the crushed ore into finer and finer particles.This leads to 26,000 tons of super fine leaching residue that are piled into the tailings dam every year.It is well known that the ultrafine tailings will reduce the mass concentration of backfill slurry significantly, and the strength of backfill will also decline correspondingly, which makes it impossible to uses ultrafine tailings as a backfill aggregate separately [13].However, on the other side, Minerals 2017, 7, 54 2 of 13 the ultrafine particles have been proven to be of benefit to the transportation of the backfill slurry [14].Combined with that, there is a large amount of classified tailings in this mine that will harm the pipeline due to its coarse particles when utilized as a backfill aggregate.Thus, the question is raised: what if utilizing a mixture of ultrafine leaching residue and coarse classified tailings as an aggregate?To test this idea, it is necessary to research the backfill characteristics with different mixing ratios of the two materials.As we know, in industrial production, the strength of backfill and the fluidity of backfill slurry are both key factors affecting the efficient recycling of tailings [15].Without the optimized mixing ratio, the inevitable sedimentation and segregation in backfill will lead to the coarse particles gathering at the bottom of a stope and the fine particles gathering at the top with water, i.e., low strength [16].What is more, backfill technology is generally utilized in pipeline transportation, therefore transportability is also a key factor that affects the choice of mixing ratio [17].There is a series of technical problems in deep mining, with the problem of backfill pipeline transportation being a significant one [18].For this mine, the common fluidity experiments in the laboratory, such as slump tests, diffusivity and the looping pipe experiment, however, cannot fully reflect the flow state and the pipeline resistance.The computational fluid dynamics (CFD) technology is applied to study the pressure and velocity of slurry transport by building a pipeline transportation model [19][20][21].Thus, it is also a reliable way to illustrate the details of slurry transport resistance and flow state.
Therefore, in this study, a series of scientific research methods was used to find the suitable backfill method to recycle leaching residues effectively.The recycling of leaching residue can not only bring huge economic benefits, but also protect the environment of the mining area.

Physicochemical Properties
The applied research measured the leaching residue size and classified tailings size using a laser granulometer (S3500, Microtrac, FL, USA), and the results are shown in Figure 1. Figure 1 shows that the leaching residue in the Fan Kou mine is ultrafine with proportions of more than 99 wt % for particles less than 19 µm in diameter.An excess of ultrafine particles makes the slurry become a paste at lower mass concentrations, which cannot meet the high mass concentration transport requirements [22][23][24].The physical properties and the chemical composition of the leaching residue and classified tailings are listed in Tables 1 and 2. The non-uniform coefficient of the leaching residue is less than 5, which indicates that it has poor gradation.In addition, the leaching residue backfill body cannot be dehydrated over time, and the strength is not sufficient due to the low permeability.Therefore, the leaching residue cannot be used as a backfill aggregate alone, and it must be used in conjunction with the classified tailings.Table 2 shows that the SiO 2 content in the leaching residue is as high as 84.08 wt %, indicating that the leaching residue is a good backfill aggregate.particles have been proven to be of benefit to the transportation of the backfill slurry [14].Combined with that, there is a large amount of classified tailings in this mine that will harm the pipeline due to its coarse particles when utilized as a backfill aggregate.Thus, the question is raised: what if utilizing a mixture of ultrafine leaching residue and coarse classified tailings as an aggregate?To test this idea, it is necessary to research the backfill characteristics with different mixing ratios of the two materials.
As we know, in industrial production, the strength of backfill and the fluidity of backfill slurry are both key factors affecting the efficient recycling of tailings [15].Without the optimized mixing ratio, the inevitable sedimentation and segregation in backfill will lead to the coarse particles gathering at the bottom of a stope and the fine particles gathering at the top with water, i.e., low strength [16].
What is more, backfill technology is generally utilized in pipeline transportation, therefore transportability is also a key factor that affects the choice of mixing ratio [17].There is a series of technical problems in deep mining, with the problem of backfill pipeline transportation being a significant one [18].For this mine, the common fluidity experiments in the laboratory, such as slump tests, diffusivity and the looping pipe experiment, however, cannot fully reflect the flow state and the pipeline resistance.The computational fluid dynamics (CFD) technology is applied to study the pressure and velocity of slurry transport by building a pipeline transportation model [19][20][21].Thus, it is also a reliable way to illustrate the details of slurry transport resistance and flow state.Therefore, in this study, a series of scientific research methods was used to find the suitable backfill method to recycle leaching residues effectively.The recycling of leaching residue can not only bring huge economic benefits, but also protect the environment of the mining area.

Physicochemical Properties
The applied research measured the leaching residue size and classified tailings size using a laser granulometer (S3500, Microtrac, FL, USA), and the results are shown in Figure 1. Figure 1 shows that the leaching residue in the Fan Kou mine is ultrafine with proportions of more than 99 wt % for particles less than 19 µm in diameter.An excess of ultrafine particles makes the slurry become a paste at lower mass concentrations, which cannot meet the high mass concentration transport requirements [22][23][24].The physical properties and the chemical composition of the leaching residue and classified tailings are listed in Tables 1 and 2. The non-uniform coefficient of the leaching residue is less than 5, which indicates that it has poor gradation.In addition, the leaching residue backfill body cannot be dehydrated over time, and the strength is not sufficient due to the low permeability.Therefore, the leaching residue cannot be used as a backfill aggregate alone, and it must be used in conjunction with the classified tailings.Table 2 shows that the SiO2 content in the leaching residue is as high as 84.08 wt %, indicating that the leaching residue is a good backfill aggregate.Table 1 shows that leaching residue is strongly acidic (pH = 3.29-3.79).Because it is easy for acid tailings to cause widespread land contamination and river pollution and because acid slurries can cause corrosion of the backfill pipe [25], the neutralization treatment of leaching residues should be carried out first to keep the backfill slurry weakly alkaline.The essence of the neutralization reaction is a process of hydrogen ion (H + ) and hydroxyl ion (OH − ) combination to form water (H 2 O) [26].Table 3 shows that the extraction toxicity of the leaching residue is within the identification standards for the hazardous wastes of China.Therefore, we just need to address the acidity of the leached residue.

Strength Test
The strength of the backfill is an important factor to ensure the safe working conditions of stopes [16].The orthogonal test is a method for designing a study to determine the influences of multiple factors and multiple levels [28].Therefore, in this work, the orthogonal test was chosen to study the compressive strength of the backfill body.The three factors are (A) the cement:sand mass ratio; (B) the leaching residue:classified tailings mass ratio; (C) and the slurry mass concentration.Every factor has four levels, and they are as follows: 1:3 (A 1 ), 1:4 (A 2 ), 1:5 (A 3 ) and 1:6 (A 4 ); 1:4 (B 1 ), 1:5 (B 2 ), 1:6 (B 3 ) and 1:7 (B 4 ); and 67 wt % (C 1 ), 69 wt % (C 2 ), 71 wt % (C 3 ), and 73 wt % (C 4 ).According to the principles of the orthogonal test, the orthogonal table of L 16 (4 3 ) was chosen to implement the backfill test.The backfill test specimens were made using a 7.07 cm × 7.07 cm × 7.07 cm standard triple test mold and cured in a standard curing box with a temperature of 21 • C and a humidity of 81%.Finally, as shown in Figure 2, the compressive strengths at 3 days, 7 days and 28 days were measured using a WDW-2000 rigid hydraulic pressure servo machine (Ruite, Guilin, China).

Diffusivity
The backfill slurry must be transported to the stope under the force of gravity or by pumping.Diffusivity tests were used to measure the fluidity of flowing concrete by the resulting dispersion area from the natural accumulation.Diffusion degree is used as a quantitative index to characterize the fluidity of the slurry; the greater the dispersion area, the better the fluidity of the slurry.The experiments were carried out using a self-designed device, which included a cylinder that was 8 cm high with an upper and lower diameter of 8 cm. Figure 3 shows the experimental method.

Diffusivity
The backfill slurry must be transported to the stope under the force of gravity or by pumping.Diffusivity tests were used to measure the fluidity of flowing concrete by the resulting dispersion area from the natural accumulation.Diffusion degree is used as a quantitative index to characterize the fluidity of the slurry; the greater the dispersion area, the better the fluidity of the slurry.The experiments were carried out using a self-designed device, which included a cylinder that was 8 cm high with an upper and lower diameter of 8 cm. Figure 3 shows the experimental method.

Diffusivity
The backfill slurry must be transported to the stope under the force of gravity or by pumping.Diffusivity tests were used to measure the fluidity of flowing concrete by the resulting dispersion area from the natural accumulation.Diffusion degree is used as a quantitative index to characterize the fluidity of the slurry; the greater the dispersion area, the better the fluidity of the slurry.The experiments were carried out using a self-designed device, which included a cylinder that was 8 cm high with an upper and lower diameter of 8 cm. Figure 3 shows the experimental method.

CFD Simulations of Pipeline Transportation
Finally, the recovery and utilization of the leaching residue are achieved through pipeline transportation.Therefore, research into the resistance of pipe flow with different pipe diameters, slurry mass concentrations and transportation velocities is very important.As shown in Figure 4, a three-dimensional model was developed for a typical L-shaped backfill pipeline for long-distance transportation, which is used here to study the transport properties of the backfill slurry.The pipe was made of a seamless steel pipe, and its detailed geometrical parameters include a 200 m vertical pipe height, a 500 m horizontal pipe length, a 150 mm inner pipe diameter, a 168 mm outer pipe diameter (with a 9 mm pipe wall thickness), a 90 • elbow angle and a 1 m elbow radius.In addition, its backfill ability is 80 m 3 /h.

CFD Simulations of Pipeline Transportation
Finally, the recovery and utilization of the leaching residue are achieved through pipeline transportation.Therefore, research into the resistance of pipe flow with different pipe diameters, slurry mass concentrations and transportation velocities is very important.As shown in Figure 4, a three-dimensional model was developed for a typical L-shaped backfill pipeline for long-distance transportation, which is used here to study the transport properties of the backfill slurry.The pipe was made of a seamless steel pipe, and its detailed geometrical parameters include a 200 m vertical pipe height, a 500 m horizontal pipe length, a 150 mm inner pipe diameter, a 168 mm outer pipe diameter (with a 9 mm pipe wall thickness), a 90° elbow angle and a 1 m elbow radius.In addition, its backfill ability is 80 m 3 /h.The leaching residue slurry is a paste slurry material because of its high mass fraction, low water content and good integrity.In the present work, the flow of the slurry was modeled as a Bingham fluid [29].The shear stress model for a Bingham fluid is: Where τ is the shear stress (Pa), τ0 is the yield stress (Pa), µ is the plastic viscosity (Pa•s), and γ  is the shear rate (1/s).
The slurry enters the backfill pipe under the action of gravity and flows through the backfill pipe.The steady conservation equations for continuous momentum and pressure are expressed as follows [30]: The leaching residue slurry is a paste slurry material because of its high mass fraction, low water content and good integrity.In the present work, the flow of the slurry was modeled as a Bingham fluid [29].The shear stress model for a Bingham fluid is: where τ is the shear stress (Pa), τ 0 is the yield stress (Pa), µ is the plastic viscosity (Pa•s), and • γ is the shear rate (1/s).
The slurry enters the backfill pipe under the action of gravity and flows through the backfill pipe.The steady conservation equations for continuous momentum and pressure are expressed as follows [30]: (3) Minerals 2017, 7, 54 6 of 13 where t is the time, ρ is the density of the slurry, v is the velocity of the slurry, X, Y and Z are the surface forces in the different directions, F is the force on the fluid element, F i is the pressure at the corresponding position, g is the gravitational acceleration, and h f is the resistance from z 1 to z 2 .
The effects of heat exchange, vibration, stress waves and compression were not considered in the simulations.The applicable boundary conditions were as follows [31,32]: (1) At the walls, the standard wall function was used in all pipe segments.
(2) At the pipe inlet, the velocity (v) function given below was used at the inlet face.
(3) At the pipe outlet, the outflow function was used at the outlet face.
The governing equations together with the computational model and boundary conditions were solved using the finite volume CFD code Fluent 14.5 [30].The equations were solved with the Semi-Implicit Pressure-Linked Equation (SIMPLE) algorithm, using second-order upwind discretization.

Neutralization Method
Because the leaching residue contains hydrochloric acid (HCl), the backfill slurry prepared by the leaching residue is acidic.Therefore, slaked lime [Ca(OH) 2 ] was used to neutralize the acidity.A mass of 100 g of the leaching residue was used to prepare a leached residue solution mass concentration of 13.2 wt %.Ca(OH) 2 was added until the measured pH value was greater than 7. Acid-base titration was performed to ensure that the backfill slurry was weakly alkaline.The mass concentration of the leaching residue solution was maintained at 13.2 wt %, and Ca(OH) 2 was added until the solution pH reached 9.76.After repeated experiments using 100 g of leaching residue, the usage of Ca(OH) 2 was 1 g.The weakly alkaline backfill slurry can avoid pipeline corrosion and pollution of the underground environment.Figure 5 shows the experimental.
where t is the time, ρ is the density of the slurry, v is the velocity of the slurry, X, Y and Z are the surface forces in the different directions, F is the force on the fluid element, Fi is the pressure at the corresponding position, g is the gravitational acceleration, and hf is the resistance from z1 to z2.The effects of heat exchange, vibration, stress waves and compression were not considered in the simulations.The applicable boundary conditions were as follows [31,32]: (1) At the walls, the standard wall function was used in all pipe segments.
(2) At the pipe inlet, the velocity (v) function given below was used at the inlet face.
(3) At the pipe outlet, the outflow function was used at the outlet face.
The governing equations together with the computational model and boundary conditions were solved using the finite volume CFD code Fluent 14.5 [30].The equations were solved with the Semi-Implicit Pressure-Linked Equation (SIMPLE) algorithm, using second-order upwind discretization.

Neutralization Method
Because the leaching residue contains hydrochloric acid (HCl), the backfill slurry prepared by the leaching residue is acidic.Therefore, slaked lime [Ca(OH)2] was used to neutralize the acidity.A mass of 100 g of the leaching residue was used to prepare a leached residue solution mass concentration of 13.2 wt %.Ca(OH)2 was added until the measured pH value was greater than 7. Acid-base titration was performed to ensure that the backfill slurry was weakly alkaline.The mass concentration of the leaching residue solution was maintained at 13.2 wt %, and Ca(OH)2 was added until the solution pH reached 9.76.After repeated experiments using 100 g of leaching residue, the usage of Ca(OH)2 was 1 g.The weakly alkaline backfill slurry can avoid pipeline corrosion and pollution of the underground environment.Figure 5 shows the experimental.

Variance Analysis
The results and the orthogonal table are shown in Table 4. SPSS software [33,34] was used to analyze the variance of the strength test and diffusivity test results, and the analysis results are shown in Table 5.When the significance level is greater than 0.05, the influence of the factors is not significant.

Strength Analysis
Table 5 shows that factor B has no significant effect on the strength of the backfill specimens, and the significance order is B = C > A. This means that the effect of the slurry mass concentration on the backfill body strength is the largest, followed by the cement:sand mass ratio and then the influence of the leaching residue:classified tailings mass ratio.
The average compressive strength values corresponding to each level are shown in Figure 6. Figure 6 shows that the strength of the backfill specimens increased with both the cement:sand mass ratio and slurry mass concentration.However, the strength effect with the leaching residue:classified tailings mass ratio has a minimum value at B2 (1:5).This indicates that from B2 (1:5) to B1 (1:4), the increase in the leaching residue causes many fine aggregates to fill the gaps between the coarse aggregates, increasing the strength of the backfill body.However, from B4 (1:7) to B2 (1:5), the increase in the fine aggregates is not sufficient to make up for the influence of the coarse aggregates on the strength of the backfill body, so the strength decreases.increase in the fine aggregates is not sufficient to make up for the influence of the coarse aggregates on the strength of the backfill body, so the strength decreases.

Diffusivity Analysis
Table 5 shows that the factor A has no significant effect on the diffusivity of the backfill slurry, and the significance order is C > A > B. This means that the effect of the slurry mass concentration and the leaching residue:classified tailings ratio on the backfill slurry diffusivity is larger than that of the cement:sand mass ratio.
The average diffusivity values corresponding to each level are shown in Figure 7. Figure 7 shows that the diffusivity increases as the leaching residue:classified tailings mass ratio decreases, but it decreases as the leaching residue:classified tailings mass ratio increases.The reason for this is that the leaching residue is made of ultrafine tailings, and its high viscosity can easily increase the flow resistance.In addition to slurry compositions at low mass concentrations, it is easy to form a paste with a large number of fine tailings, and it can cause the viscosity of the slurry to increase and show poor fluidity.Therefore, we consider the leaching residue:classified tailings mass ratios of 1:5-1:7 (B2 and B3) and slurry mass concentrations of 69 wt %-71 wt % (C2 and C3) as the range for achieving good diffusivity.

Diffusivity Analysis
Table 5 shows that the factor A has no significant effect on the diffusivity of the backfill slurry, and the significance order is C > A > B. This means that the effect of the slurry mass concentration and the leaching residue:classified tailings ratio on the backfill slurry diffusivity is larger than that of the cement:sand mass ratio.
The average diffusivity values corresponding to each level are shown in Figure 7. Figure 7 shows that the diffusivity increases as the leaching residue:classified tailings mass ratio decreases, but it decreases as the leaching residue:classified tailings mass ratio increases.The reason for this is that the leaching residue is made of ultrafine tailings, and its high viscosity can easily increase the flow resistance.In addition to slurry compositions at low mass concentrations, it is easy to form a paste with a large number of fine tailings, and it can cause the viscosity of the slurry to increase and show poor fluidity.Therefore, we consider the leaching residue:classified tailings mass ratios of 1:5-1:7 (B2 and B3) and slurry mass concentrations of 69 wt %-71 wt % (C2 and C3) as the range for achieving good diffusivity.
Minerals 2017, 7, 54 8 of 13 increase in the fine aggregates is not sufficient to make up for the influence of the coarse aggregates on the strength of the backfill body, so the strength decreases.

Diffusivity Analysis
Table 5 shows that the factor A has no significant effect on the diffusivity of the backfill slurry, and the significance order is C > A > B. This means that the effect of the slurry mass concentration and the leaching residue:classified tailings ratio on the backfill slurry diffusivity is larger than that of the cement:sand mass ratio.
The average diffusivity values corresponding to each level are shown in Figure 7. Figure 7 shows that the diffusivity increases as the leaching residue:classified tailings mass ratio decreases, but it decreases as the leaching residue:classified tailings mass ratio increases.The reason for this is that the leaching residue is made of ultrafine tailings, and its high viscosity can easily increase the flow resistance.In addition to slurry compositions at low mass concentrations, it is easy to form a paste with a large number of fine tailings, and it can cause the viscosity of the slurry to increase and show poor fluidity.Therefore, we consider the leaching residue:classified tailings mass ratios of 1:5-1:7 (B2 and B3) and slurry mass concentrations of 69 wt %-71 wt % (C2 and C3) as the range for achieving good diffusivity.

Proportioning Scheme
To meet the safety requirements for production, the strength of the backfill body is as follows: (1) room stopes: the cement:sand mass ratio is 1:6~1:8; 28 days compressive strength is greater than 4 MPa; (2) pillar stopes: the cement:sand mass ratio is above 1:12; 28 days compressive strength is 2-3 MPa; (3) artificial bottom, casting surface and first backfill layer: the cement:sand mass ratio is 1:3-1:4; 3 days compressive strength is greater than 1.5 MPa, and 28 days compressive strength is greater than 5 MPa.
Based on the test results and strength requirements, the proportioning scheme includes the cement:sand mass ratio of 1:3, the leaching residue:classified tailings mass ratios of 1:4, 1:6 and 1:7, and a slurry mass concentration of 71 wt % and 73 wt %.Regarding alignment of the required strength and diffusivity (with the leaching residue:classified tailings mass ratio 1:5-1:7 and slurry mass concentration 69 wt %-71 wt %), the proportioning scheme includes the cement:sand mass ratio of 1:3, the leaching residue:classified tailings mass ratios of 1:6 and 1:7, and slurry mass concentration of 71 wt %.

Pressure
Preparation of the slurry using the proportioning scheme that we chose (the cement:sand mass ratio of 1:3, the leaching residue:classified tailings mass ratios of 1:6 and 1:7, and slurry mass concentration of 71 wt %), and the results of the pressure tests, are shown in Table 6.To achieve the self-flowing transport of a backfill material through a pipeline, the gravitational potential energy must be greater than the resistance loss of the pipeline, which is defined as the total pressure difference between the inlet and outlet of the pipeline.The equations for the gravitational potential energy and resistance loss are as follows [35]: p = ρgh (5) where p is the gravitational potential energy (Pa), g is the gravitational acceleration (i.e., 9.8 m/s 2 ), h is the height difference (m), h f is the resistance loss (Pa), p y is the total pressure difference (Pa), p in is the total pressure at the inlet (Pa), and p out is the total pressure at the outlet (Pa).As shown in Table 6, the resistance values of case 1 and case 2 are smaller than the gravitational potential energy, and both meet the requirements for self-flowing transportation.Thus, the backfill slurry can be carried to the stopes properly; eliminating the use of the pump will greatly decrease the cost of backfill.

Velocity
Controlling the transport velocity of the slurry is also an important factor in pipeline transport [36].The speed needs to be maintained within a suitable range to prevent the solid particles from settling or the pipe wall from wearing.The velocities of the slurry at the elbow for different cases are shown in Figure 8.As shown in Figure 8, the flow core zone gradually becomes smaller and moves from the center of the pipe to the exterior of the elbow, and the flow state of the slurry fluctuates.The maximum velocities for the different leaching residue:classified tailings mass ratios of 1:6 and 1:7 are 2.69 m/s and 2.72 m/s, respectively.Figure 9 shows the velocity distribution at the outlet of the pipe with different leaching residue:classified tailings mass ratios.As shown in Figure 9, the velocity distribution has areas of localized enlargement, and the high velocity areas are still concentrated in the center of the pipe.The maximum velocities for the different leaching residue:classified tailings mass ratios of 1:6 and 1:7 are 2.30 m/s and 2.31 m/s, respectively.The velocity variation trend shows an increase in the vertical pipe and a decrease in the horizontal pipe; the maximum velocity occurs at the elbow of the pipe.The mine backfill experience of South Africa indicated that the velocity of the horizontal pipe should not exceed 4 m/s [19].Therefore, the two proportioning schemes both meet the requirements of backfill.

Recoverability
Regarding the comprehensive analysis above, to recycle the leaching residue as much as possible under the premise of meeting the strength and pipeline transportation requirements, the final   Figure 9 shows the velocity distribution at the outlet of the pipe with different leaching residue:classified tailings mass ratios.As shown in Figure 9, the velocity distribution has areas of localized enlargement, and the high velocity areas are still concentrated in the center of the pipe.The maximum velocities for the different leaching residue:classified tailings mass ratios of 1:6 and 1:7 are 2.30 m/s and 2.31 m/s, respectively.The velocity variation trend shows an increase in the vertical pipe and a decrease in the horizontal pipe; the maximum velocity occurs at the elbow of the pipe.The mine backfill experience of South Africa indicated that the velocity of the horizontal pipe should not exceed 4 m/s [19].Therefore, the two proportioning schemes both meet the requirements of backfill.

Recoverability
Regarding the comprehensive analysis above, to recycle the leaching residue as much as possible under the premise of meeting the strength and pipeline transportation requirements, the final The velocity variation trend shows an increase in the vertical pipe and a decrease in the horizontal pipe; the maximum velocity occurs at the elbow of the pipe.The mine backfill experience of South Africa indicated that the velocity of the horizontal pipe should not exceed 4 m/s [19].Therefore, the two proportioning schemes both meet the requirements of backfill.

Figure 1 .
Figure 1.Particle size grading of leaching residue and classified tailings.

Figure 1 .
Figure 1.Particle size grading of leaching residue and classified tailings.

Figure 2 .
Figure 2. Pressure testing machine and test block: (a) pressure testing machine and (b) test block.

Figure 2 .
Figure 2. Pressure testing machine and test block: (a) pressure testing machine and (b) test block.

Figure 2 .
Figure 2. Pressure testing machine and test block: (a) pressure testing machine and (b) test block.

Figure 4 .
Figure 4.The diagram of the pipeline transport system.

Figure 4 .
Figure 4.The diagram of the pipeline transport system.

Figure 6 .
Figure 6.The average compressive strength (curing age: 3 days, 7 days and 28 days) of the backfill body at each level.

Figure 7 .
Figure 7.The average diffusivity of the slurry at each level.

Figure 6 .
Figure 6.The average compressive strength (curing age: 3 days, 7 days and 28 days) of the backfill body at each level.

Figure 6 .
Figure 6.The average compressive strength (curing age: 3 days, 7 days and 28 days) of the backfill body at each level.

Figure 7 .
Figure 7.The average diffusivity of the slurry at each level.Figure 7. The average diffusivity of the slurry at each level.

Figure 7 .
Figure 7.The average diffusivity of the slurry at each level.Figure 7. The average diffusivity of the slurry at each level.

8 .
As shown in Figure8, the flow core zone gradually becomes smaller and moves from the center of the pipe to the exterior of the elbow, and the flow state of the slurry fluctuates.The maximum velocities for the different leaching residue:classified tailings mass ratios of 1:6 and 1:7 are 2.69 m/s and 2.72 m/s, respectively.

Figure 9
Figure9shows the velocity distribution at the outlet of the pipe with different leaching residue:classified tailings mass ratios.As shown in Figure9, the velocity distribution has areas of localized enlargement, and the high velocity areas are still concentrated in the center of the pipe.The maximum velocities for the different leaching residue:classified tailings mass ratios of 1:6 and 1:7 are 2.30 m/s and 2.31 m/s, respectively.

Table 1 .
Physical properties of leaching residue and classified tailings.

Table 2 .
Chemical composition of leaching residue size and classified tailings (unit in wt %).

Table 3 .
Extraction toxicity of the leaching residue (unit in mg/L).

Table 4 .
The results of the compressive strength test and diffusivity test.

Table 5 .
Variance analysis of the compressive strength test and diffusivity test.

Table 6 .
The results of the compression strength test and diffusivity test.