Petrographic and Geochemical Analysis of Indus Sediments: Implications for Placer Gold Deposits, Peshawar Basin, NW Himalaya, Pakistan

: Alluvial placer gold deposits that accumulate in streams across the globe are essentially allochthonous sedimentary deposits that are transported from their source to their location of deposition. The purpose of this study was to ﬁnd placer gold deposits in alluvial sediments along the Indus River in the NW Himalaya of Pakistan. The investigated region was divided into ﬁve clusters based on river morphology. The research focused on mineralogical distribution, sediment source, gold transport distance, elemental composition, and gold concentration in river sediments. Throughout, during the deposition at point and channel bars, the mixed source of alluvial sediments was revealed by its mineralogical composition. However, the SEM analysis demonstrated that the gold grains had a high ﬂatness index, indicating that they had been transported a signiﬁcant distance. The elemental composition of several samples revealed a signiﬁcant concentration of silicon dioxide, iron oxide, and alumina oxide transported from the Himalaya. The study of the trace elements indicated gold and related base metals with granitic provenance were transported from an acidic/granitic source. Based on gold concentration, it is demonstrated that the left riverbank (clusters C1, C2, and C3) has a higher concentration of gold deposits and higher potential for economic gold exploration than the right bank (clusters C4 and C5) due to the lower velocity of running water in the study area. The ﬁndings revealed that the studied area has good potential for commercial exploration of gold resources, and the workﬂow can be adopted in any region with a similar geological setting and morphology.


Introduction
Gold is one of the most valuable minerals on the planet, consisting mostly of elemental gold with traces of mercury, silver, copper, iron, nickel, manganese, and tinier amounts of selenium, platinum-group metals, bismuth, and rhenium [1][2][3][4][5]. When the gold is about 4 g/ton with other accumulated deposits, it is included in mineral deposits [6]. Placer gold is a type of allochthonous sedimentary deposit that mostly accumulates along shallow streams and rivers with other heavy minerals [7,8]. Mineralogy, morphology, elemental composition, and concentration of trace elements within placers are all debatable studies for the exploration of economic gold resources. This analysis aided in the identification of gold mineralization, prospective source rock, major oxides associated with gold, and concentration of economic gold deposits [9][10][11][12][13]. Moreover, since the accumulation of economic gold deposits is largely reliant on morphological characteristics, distinct clusters may be identified. As they influence the flow of water, features such as canyon exits, waterfalls, and point bars may change its accumulation in the same place. The aforementioned characteristics substantially reduce water velocity and may be good places for the deposition of heavy minerals, such as gold grains [5].
Gold exploration in the NW Himalaya along the Indus River has been ongoing for a long time [9]. Over the past several decades, national and international organizations have boosted their exploration operations to investigate economic minerals. In 1992-1995, the Gold Exploration and Mineral Analysis Project (GEMAP) undertook commercial mineral investigations, mostly for gold, as part of the Australian Aid for International Development [9]. The aim of this project was to focus on gold and associated minerals in the NW Himalaya. Moreover, many investigations in this region indicate the possibility of gold occurrences eroded from their source rocks [14][15][16][17].
The study area is located in the eastern Peshawar Basin of the NW Himalaya, where alluvial sediments of the Indus River are being investigated. Reconnaissance surveys and earlier geological investigations in several areas of the Peshawar Basin have shown the presence of heavy minerals, including gold (Au), in river deposits [18][19][20][21]. However, there are no detailed studies available on petrographic, geochemical, or spatial distribution models based on geochemical analysis. Similarly, the identification of economic Au in possible areas of the river environment has not previously occurred. The objectives of this research were to determine the mineralogical and elemental compositions of the alluvial sand deposits in order to understand their possible source and chemical composition. Further, the morphology of alluvial gold is determined based on its internal structure and deposition pattern. The placer gold deposits and the associated trace elements with them are also analyzed in order to determine the economic potential of gold deposits. Finally, a model was developed to identify potential areas for profitable investigation of placer gold deposits.

Regional Geology
The Himalaya are the result of the continuous collision of the Indian and Eurasian plates. The Kohistan Island Arc (KIA) is a Cretaceous-era intraoceanic island arc that has been situated between these two plates [22]. The Eurasian plate is separated from the KIA by the Main Karakoram Thrust (MKT), also known as the Shyoke Suture Zone (SSZ) (Figure 1). The Indian Plate and KIA are separated by the Indus-Tsangpo Suture Zone (ITSZ), a major tectonic boundary. The KIA is divided into three parts: the northern and western parts (volcanics and metasediments), the central part (batholith), and the southern part (e.g., contains three tectono-metamorphic units: the Chilas Complex, Kamila Amphibolite, and Jijal Complex). The Himalaya extend about 2000 km in length and are further subdivided into the Greater Himalaya (GH), Lesser Himalaya (LH), and Tethyan Himalaya (TH) [22,23]. The Main Central Thrust (MCT) separates the high-grade crystalline rocks of the GH from the low-grade crystalline rocks of the LH. However, in the west Himalaya, the Zanskar Shear Zone (ZSZ), also known as the South Tibetan Detachment (STD) fault, is present. The Main Boundary Thrust (MBT) separates the LH from the Sub-Himalayan/Himalayan Foreland Basin [24]. The area consists of vast networks of tributaries connected to rivers that run through the Himalaya and impact sediment erosion, transport, and deposition over a long distance ( Figure 1). Economic heavy minerals are also transported and deposited along the adjacent areas of these rivers. The Indus River is the main river in the NW Himalaya, rising from GH tributaries including the Hunza, Ghizar, Gilgit, Shyok, and Shigar rivers [10]. The Hunza River originates from the Karakoram through different lithological units, mainly Permian and Triassic limestone and Hunza plutons. It enters the KIA after passing through the Kohistan Batholith (KB). Further, the river enters the metasedimentary rocks of the Gilgit complex by joining the Ghizar River, also known as the Gilgit River. From there on, the Gilgit River connects to the Indus River and flows into the KB. Both the Shyok River, which starts in the SSZ, and Astor River,  [25]. river in the NW Himalaya, rising from GH tributaries including the Hunza, Ghizar, Gilgit, Shyok, and Shigar rivers [10]. The Hunza River originates from the Karakoram through different lithological units, mainly Permian and Triassic limestone and Hunza plutons. It enters the KIA after passing through the Kohistan Batholith (KB). Further, the river enters the metasedimentary rocks of the Gilgit complex by joining the Ghizar River, also known as the Gilgit River. From there on, the Gilgit River connects to the Indus River and flows into the KB. Both the Shyok River, which starts in the SSZ, and Astor River, that rises in the Deosai Mountains, flow from the KB and join the Shigar River before joining the Indus River in the KIA. The Indus River flows mostly parallel to the strike of KIA. After passing through the Main Mantle Thrust (MMT), it eventually enters the Indian Plate's Besham Basement Complex (BBC) and flows through the Indian Plate rocks. The BBC consists of heterogeneous gneisses, quartzofeldspathic gneisses, amphibolites, granodiorites, pegmatites, quartzite, metacarbonate sedimentary rocks, and leucocratic granites [25]. The Peshawar Basin is an intermontane basin located on the Indian Plate in the LH, along the southern edge of the Pakistan Himalaya [5,23]. This intermontane basin originated in the Plio-Pleistocene during the late stages of orogenetic episodes caused by Figure 1. The regional tectonic map of Himalaya indicating the Peshawar basin and the major rivers flowing from the Himalaya to the study area, modified after [24,26,27].
The Peshawar Basin is an intermontane basin located on the Indian Plate in the LH, along the southern edge of the Pakistan Himalaya [5,23]. This intermontane basin originated in the Plio-Pleistocene during the late stages of orogenetic episodes caused by Indian-Eurasian plate collisions [24,28,29]. It is responsible for the sediment accumulation in the Attock-Cherat Range and causes pounding drainage [28]. Exposed igneous and metamorphic rocks eroded from northern Pakistan have the potential to provide primary gold in the Himalaya that can be deposited mostly via river systems [5]. These depositions may consist of scattered economic gold clusters deposited by gravity settling [29,30].
The Indus River flows through the Peshawar Basin of the NW Himalaya in the study region, passing through the Alkaline Igneous Province of the Peshawar Plain and unconsolidated sands, silt, and loess of Quaternary age. The basin is bounded by the Attock-Cherat Range to the south, the Gandghan Range to the east, and the Khyber Range to the west (Figure 2a). These ranges comprise metasediments from the Himalaya as well as unmetamorphosed sediments from the GH's Kohat-Potwar plateau [21,31]. The Peshawar Basin is composed of sedimentary fold-and-thrust belts to the south and metamorphic terrains to the north [32]. The Peshawar Basin lithostratigraphy is composed of lithological units ranging from the Precambrian to the Quaternary (Figure 2b). Precambrian formations include the Dakhner Formation, Manki Formation, and Shakhot Formation. The Paleozoic age comprises the Ambar Formation, Misri Formation, Panjpir Formation, and Nowshera Formation [5]. The Peshawar Basin sediments are mostly lacustrine silt, river sand, and gravel [33]. The Quaternary deposits of the Peshawar Basin are mainly composed of alluvial fans, flood plains, lacustrine, deltaic, fluvial, and loess deposits. Pleistocene lakes within the Peshawar Basin are responsible for the presence of parallel bedded, fining upward sand layers, silts, and clays [34].  [5,35].

Materials and Methods
Based on river morphology, the study region is divided into five clusters, including Atttock-Khurd, Mula Mansoor, Kund, and Allah Dher (Figure 3b). The river morphology was mainly focused on midpoint bars and the inner side of meandering, because they are suitable areas for placer gold deposits. The sedimentary deposits in the study area are mostly composed of river channels and point bars with sand to clay-sized particles found in a finning upward sequence. The various sizes were determined in the field by observing

Materials and Methods
Based on river morphology, the study region is divided into five clusters, including Atttock-Khurd, Mula Mansoor, Kund, and Allah Dher (Figure 3b). The river morphology was mainly focused on midpoint bars and the inner side of meandering, because they are suitable areas for placer gold deposits. The sedimentary deposits in the study area are mostly composed of river channels and point bars with sand to clay-sized particles found in a finning upward sequence. The various sizes were determined in the field by observing the grittiness of the rocks. From each cluster along the Indus River, we obtained a total of 25 samples. After removing organic content by hand picking, about 8-20 kg of material was collected from a 1 m depth for each sample. The samples were subsequently taken to the riverbank for panning. Further, the heavy mineral concentrations in the samples were collected from the field by refining through sieving and panning to decrease the volume and weight (100-200 g). The samples were named based on their cluster design and collection from the field (Figure 3b).  Further, the samples were studied using a stereoscope (Bioevopeak Inc, Seattle, WA, USA), and gold granules were recovered for scanning electron microscopy (SEM, at University of Azad Jammu and Kashmir, Pakistan) analysis to study the morphology of the grains. Representative samples from each cluster, on the other hand, were processed into thin sections and then powdered for X-ray fluorescence spectroscopy (XRF at Centralized Resources Laboratory, University of Peshawar, Pakistan.) and atomic adsorption spectroscopy (AAS at Centralized Resources Laboratory, University of Peshawar, Pakistan) analysis to identify the mineralogical composition, elemental compositions, and quantity of gold in the studied samples, respectively. inductively coupled plasma-atomic emission spectroscopy (ICP-OES at Pakistan Institute of Nuclear Science and Technology (PINSTECH), Islamabad, Pakistan.) analysis was also used to identify the trace elements. The study concluded with a geographical spatial distribution model of gold that identifies economic zones in the studied region.
The petrographic examination was carried out by producing thin sections of sediment granules for mineralogical identification by using a Lica DM 750P microscope ( At the lab of the Institute of Geology, University of Azad Jammu and Kashmir, Pakistan, in polarized light and cross nickel). Further, the opaque minerals were analyzed for the identification of heavy minerals by using a stereoscope. SEM was used to investigate the morphological characteristics and internal structures of gold grains. SEM images were used to estimate the flatness index (FI) of gold grains by comparing their length, width, and Further, the samples were studied using a stereoscope (Bioevopeak Inc., Seattle, WA, USA), and gold granules were recovered for scanning electron microscopy (SEM, at University of Azad Jammu and Kashmir, Pakistan) analysis to study the morphology of the grains. Representative samples from each cluster, on the other hand, were processed into thin sections and then powdered for X-ray fluorescence spectroscopy (XRF at Centralized Resources Laboratory, University of Peshawar, Pakistan.) and atomic adsorption spectroscopy (AAS at Centralized Resources Laboratory, University of Peshawar, Pakistan) analysis to identify the mineralogical composition, elemental compositions, and quantity of gold in the studied samples, respectively. inductively coupled plasma-atomic emission spectroscopy (ICP-OES at Pakistan Institute of Nuclear Science and Technology (PINSTECH), Islamabad, Pakistan.) analysis was also used to identify the trace elements. The study concluded with a geographical spatial distribution model of gold that identifies economic zones in the studied region.
The petrographic examination was carried out by producing thin sections of sediment granules for mineralogical identification by using a Lica DM 750P microscope (At the lab of the Institute of Geology, University of Azad Jammu and Kashmir, Pakistan, in polarized light and cross nickel). Further, the opaque minerals were analyzed for the identification of heavy minerals by using a stereoscope. SEM was used to investigate the morphological characteristics and internal structures of gold grains. SEM images were used to estimate the flatness index (FI) of gold grains by comparing their length, width, and thickness. FI values were computed using the following formula: (l + b)/2t, where l is the length, b is the breadth, and t is the thickness of the grain [5]. It helps with the interpretation of gold deposits transported a distance from the source rock. The settings employed for the SEM analysis included an accelerating voltage of −10 kV and a counting duration of 40 s.
The elemental compositions of the samples were identified using XRF (EDX-7000 instrumentat Centralized Resource Laboratory, University of Peshawar, Pakistan.) analysis. For this purpose, 10 g of pan concentrate sample was converted into powdered form. The boric jackets were produced from powdered materials, which were put in a plastic beaker and mixed with 2 cc of elvactite biding agent before drying for 15 min. The samples were placed into a steel ring (3-4 cm in diameter) to form a disk. Powdered boric acid was poured into the sample, which was subsequently compressed at 20 tons for 15-30 s. It helps in the preparation of boric jackets that have been dried for 15 min. The resulting peaks were then calibrated in order to determine the various components and their percentage composition in each sample. The X-Ray Data Booklet [36] was used to calibrate the energy (k) values as well as the photon bombardment range. The ICP-OES analysis, on the other hand, was used to determine accurate ranges of traces (including gold) and rare earth elements from different clusters, which was then used to pinpoint locations with greater potential for gold deposits. Before the study started, the following parameters were set: radio frequency generator power, 1150 W; pump rate, 50 rpm; auxiliary gas flow rate, 0.5 L min −1 ; and viewing plasma height, 14 mm. A scan run was originally conducted on all of the sample solutions to validate the targeted elements. For each element, three distinct analytical wavelengths were preselected. For additional quantitative investigations, the wavelength with the highest intensity, few detection limits, and low influence on the background of an emission line was selected among these. To begin the analysis, samples were also aspirated for 1 min, and the equipment was planned to generate the average values by analyzing each solution three times.
Finally, AAS was utilized to determine the quantity of gold in the studied samples. It comprises the measurement of gold in typical samples using the graphite furnace atomic absorption spectrometry technique [37,38]. The samples were finely powdered for this purpose, and 10 g of this powder was placed in a conical flask using an analytical balance. Then, aqua regia was added to the sample (mixture of HCl and HNO 3 , 3:1), for 10 min before being put on a hot plate and heated to about 80 to 90 • C. After allowing the samples to cool for 10 min, distilled water was added to dilute the solution to 50 mL. The solution was allowed to rest for a while so that the solid component could settle. The beaker's content was filtered and washed with 6N HCl to get a filtrate of 50 mL volume. The filtrate was added to a 250 mL separator funnel, followed by another 50 mL of distilled water to make the solution 100 mL. After that, 20 mL of methyl-isobutyl ketone was added, and the mixture was rolled for 8 min. After some time, the two layers were formed in the separatory funnel, with the lower layer being acidic (inorganic) and the upper layer containing gold, being methyl-isobutyl ketone. Finally, the two layers were separated from each other, and samples were analyzed on AAS, by using formula (1) through which the values of gold in ppm ( µg g ) were calculated [39].
V a = volume of the sample after dilution. V b = volume taken for methyl-isobutyl ketone (MIBK) extraction. A standard sample of gold was run to ensure the precision and accuracy of the results, which are shown in the concentration and absorbance graph. The AAS plastic nebulizer was discharged into the sample to conduct this analysis. The AAS sucked in the fluid and detected the gold concentration, displaying the results in milligrams per liter on the system associated via its software. The readings were then converted from milligrams per liter to parts per million (ppm). Following these experiments, an ArcGIS geographical distribution model was developed using AAS data. The inverse distance weighted (IDW) interpolation technique, which provides a definite result on the distribution of placer gold to find the economic potential zones in the study area, was employed for this purpose.

Petrographic Study
A petrographic study was carried out to determine the mineralogical composition within Indus River deposits. The microscopic features of the quartz grains mostly indicate that they are angular to subangular. The general composition indicates that the quartz ranges from 40% to 49%. The quartz grains are monocrystalline and polycrystalline (Figure 4k). Whereas monocrystalline quartz varies from 30% to 42% and polycrystalline quartz ranges from 3% to 14%. The feldspars recognized as plagioclase, orthoclase, and microcline perthite in the samples are up to 24% to 37%. Further, the rock fragments include igneous (2% to 8%), metamorphic (3% to 8%) and sedimentary (2% to 7%) clasts. These rock fragments are of different shapes, including angular to subangular. The accessory minerals (including muscovite and biotite constitute) vary from 3% to 10%, while tourmaline, hornblende, and epidote range from 3% to 7% (Table 1). The opaque minerals, on the other hand, vary from 1% to 5%. Because this study is based on clusters, the proportion of quartz in clusters C4 and C5 is slightly higher than in C1, C2, and C3, whereas clusters C1, C4, and C5 have more feldspar content than C2 and C3. Clusters C2 and C5 are enriched in igneous and sedimentary rock fragments. Cluster C2 contains slightly more metamorphic fragments than other clusters. Further, clusters C2 and C3 have relatively high accessory minerals, though clusters C1 and C2 have comparatively low opaque minerals ( Figure 5).     In order to investigate the unidentified mineral type in heavy minerals, opaque mineral identification was also analyzed using a stereoscope. Zircon, olivine (Figure 4l Table 2). The alteration of plagioclase to sericite (sericitization) is also observed (Figure 4d). Plagioclase also consists of sericite and biotite (Figure 4a), which were altered into muscovite due to sedimentary alterations.

Morphological Features of the Alluvial Gold
The gold particles picked with the stereoscope were further analyzed to understand the internal structure and transport distance of the alluvial gold particles. The morphology of gold particles from recent alluvial deposits varies according to transport distance due to internal ductile deformation [40]. It is assumed that the majority of the grains are well rounded and folded (Figure 6a,b). Their surface textures are almost smooth, elongated, and flattened (Figure 6c-f). The particle size ranges from 100 to 3000 µm. The recovered grains' flatness index (FI) values range from 4.8 to 31.21, indicating their transit distance from a distal source in an alluvial setting (Table 3).   C1  3  3  53  15  5  13  8  3  100  C2  2  4  52  16  4  15  7  2  100  C3  2  2  54  12  6  17  6  3  100  C4  3  2  50  13  7  17  7  4  100  C5  2  3  52  10  10  16  6 3 100

Morphological Features of the Alluvial Gold
The gold particles picked with the stereoscope were further analyzed to understand the internal structure and transport distance of the alluvial gold particles. The morphology of gold particles from recent alluvial deposits varies according to transport distance due to internal ductile deformation [40]. It is assumed that the majority of the grains are        Table 4).

Trace and Rare Earth Elements
ICP-OES analysis was performed to identify and quantify trace and rare earth elements in representative samples of different clusters. The results indicated higher ranges of Mn, V, Ce, Cr, La, and Nd can be explored economically for industrial usage. However, elements such as Zn, Y, As, and Co were identified in lesser amounts. Precisely, gold is detected in this analysis with these trace and rare earth elements. It is observed that the clusters (C1, C2, C3) have a higher gold content value than the other clusters (C4, C5). The rare earth elements La, Ce, Nd, Yb, and Lu were also detected. La, Ce, and Nd are light rare earth elements (LREE), whereas Yb and Lu are heavy rare earth elements (HREE). The trace element and rare earth element composition of the alluvial sediments are given in Table 5.
The correlations between the detected trace element composition of the sedimentary bulk and the upper continental crust (UCC) are also evaluated [41]. As a result, trace element concentrations are influenced by weathering, provenance, sediment sorting, diagenesis, and aqueous geochemistry. The Indus sediments are considerably enriched in Au, As, Lu, Sc, Yb, and Zn and depleted in Ba, Ce, Co, Cr, La, Mn, Nd, Ni, Sc, Sr. V, and Y compared to UCC (Figure 7).
Further, the granite provenance data plots (Cr/v vs. Y/Ni) also demonstrate that these sediments come from an acidic/granitic source (Figure 8).

Gold Determination in Quaternary Sediments
According to the AAS analysis, the quantity of gold varies in each sample from different clusters. Overall, the results specified that the gold detection ranged from 0.34 to 13.02 ppm in the studied area. The clusters (C1, C2, C3) on the left bank of the Indus River have high values. The clusters (C4, C5) on the right bank contain a low concentration of gold. The average concentration of economic gold for exploration is greater than 5 ppm [43]. The findings show that the average value of clusters C1, C2, and C3 has a greater gold content and can be more cost-effective for exploration (Table 6).   Further, the granite provenance data plots (Cr/v vs. Y/Ni) also demonstrate that these sediments come from an acidic/granitic source (Figure 8). Further, the gold spatial distribution model was developed using the results of the AAS analysis ( Figure 9). According to the spatial distribution of gold, the southeastern half (C1) of the studied area has significant concentrations of gold deposits, although the C2 and C3 on the same side of the river had AAS values of more than 10 ppm gold. C4 and C5 have the lowest gold concentrations.

Gold Determination in Quaternary Sediments
According to the AAS analysis, the quantity of gold varies in each sample from different clusters. Overall, the results specified that the gold detection ranged from 0.34 to 13.02 ppm in the studied area. The clusters (C1, C2, C3) on the left bank of the Indus River have high values. The clusters (C4, C5) on the right bank contain a low concentration of gold. The average concentration of economic gold for exploration is greater than 5 ppm [43]. The findings show that the average value of clusters C1, C2, and C3 has a greater gold content and can be more cost-effective for exploration (Table 6).    Further, the gold spatial distribution model was developed using the results of the AAS analysis ( Figure 9). According to the spatial distribution of gold, the southeastern half (C1) of the studied area has significant concentrations of gold deposits, although the C2 and C3 on the same side of the river had AAS values of more than 10 ppm gold. C4 and C5 have the lowest gold concentrations.

Discussions
Petrographic studies of river sediments were carried out to determine the origin of these sediments. The petrographic investigation revealed that the detected quartz is mostly angular, subangular, and rounded in shape. It was observed in all of the clusters, suggesting a mixed Himalayan origin. It also suggests that the sediments were mostly composed of epidote, sericite, tourmaline, zircon, and actinolite. Epidote is derived from greenschists or formed by hydrothermal alteration, while sericite is a fine-grained white mica formed by feldspar alteration. In felsic igneous rocks, pegmatites, and metamorphic rocks, tourmaline is formed (granet gneiss). Zircon may be identified in three types of rocks: igneous, metamorphic, and sedimentary. Actinolite indicates that it was metamorphosed from Himalayan mafic and ultramafic rocks. The lithic fragments are composed of volcanic (Figure 3f), metamorphic, and sedimentary rocks, indicating a diverse source of Himalayan sediments. The mineral assemblage suggests that these sediments were derived from plutonic, volcanic basic, and ultrabasic rocks. Certain mineral assemblages, on the other hand, indicate the origin of metamorphic and sedimentary rocks.
In the QFL diagram [44], the modal compositional data of the alluvial sediments were plotted on the recycled orogen provenance field that occurred in the Himalaya (Figure 10a,b), where igneous, metamorphic, and sedimentary rocks were deformed and uplifted due to the ongoing Himalayan Orogeny, and these sediments were transported by active fluvial systems, where finally this detritus (also including gold grains and other heavy minerals) was deposited where the velocity of water sufficiently dropped. It is believed that the Indus River contains a rich amount of sediment from the Karakorum and Hindukush regions. The sediments of the Hunza River originate from the Ladakh and Kohistan tributaries. Further, the Shyok and Astor rivers (originating in the Deosai Mountains) and the Gilgit River (originating in the Gilgit Complex) are depositing sediments from Himalayan tributaries through the Indus River.
According to the morphological study, the samples mostly consist of microscopic flaky gold grains. The roundness, flatness, flakiness, and smallness are all related to a spongy surface appearance. It indicates that gold grains have traveled a long distance from the source through the active fluvial system of the Himalaya. It is interpreted that the highenergy fluvial system with a sharp slope often contains placer deposits that are occasionally altered. The Ako'ozam and Njabilobe are river streams in the southwestern Cameroon range that also transport gold grains through an active fluvial system. The gold grains recovered from the Indus sediments range from 100 to 3000 µm, whereas the gold particles of the Ako'ozam and Njabilobe stream placers range from 50 to >600µm [45]. In both cases, the gold grains have a sub-rounded, elongated, and folded shape. The Ako'ozam and Njabilobe gold particles, on the other hand, were transported from a nearby source, while the Indus gold particles were transported from a distal source.
The elemental composition of the sediments is a very powerful tool in provenance analysis. The Fe 2 O 3 is thought to have been derived from hematite, limonites, and magnetite. The CaO and TiO 2 originated from limestone and either rutile or sphene, respectively. Titanite (sphene) is therefore an accessory mineral in I-type granites as well as formed in metamorphosed rocks. This shows the presence of I-type granites and metamorphosed rocks in the source. As a result, intrusion-related gold systems are associated with I-type granites [46]. The Amani River in Tanzania also transports gold grains through fluvial systems. As a comparison between the geochemical characteristics of these rivers, it is interpreted that these characteristics are similar in both rivers, as both rivers have a high SiO 2 content. The Amani River, on the other hand, has a wide range of silica concentration (45% to 75%) owing to acidic and alkaline rocks, but the Indus River has a narrow range [41]. Similarly, the least abundant oxides in Amani River sediments are Cr 2   heavy-mineral assemblages, ZRT + LgM = ultrastable minerals zircon tourmaline rutile + low grade minerals mostly epidote group minerals, A + Px = amphibole + pyroxene, Gt + HgM = garnet + high-grade minerals mainly sphene, carried by the Indus River plot near the boundary between recycled orogen (RO), magmatic arc (MA), and continental block (CB) provenance fields [44].
The elemental composition of the sediments is a very powerful tool in provenance analysis. The Fe2O3 is thought to have been derived from hematite, limonites, and magnetite. The CaO and TiO2 originated from limestone and either rutile or sphene, respectively. Titanite (sphene) is therefore an accessory mineral in I-type granites as well as formed in metamorphosed rocks. This shows the presence of I-type granites and metamorphosed rocks in the source. As a result, intrusion-related gold systems are associated with I-type granites [46]. The Amani River in Tanzania also transports gold grains through fluvial systems. As a comparison between the geochemical characteristics of these rivers, Figure 10. The triangular plots show (a) petrography, Q = quartz, F = feldspar, L-Lc = lithic-lithics carbonates and (b) heavy-mineral assemblages, ZRT + LgM = ultrastable minerals zircon tourmaline rutile + low grade minerals mostly epidote group minerals, A + Px = amphibole + pyroxene, Gt + HgM = garnet + high-grade minerals mainly sphene, carried by the Indus River plot near the boundary between recycled orogen (RO), magmatic arc (MA), and continental block (CB) provenance fields [44].
The concentration of trace and rare earth elements in alluvial sediments is another crucial factor in determining their origin. There is an enrichment of LREE in the studied alluvial sediments compared to HREE, suggesting that these sediments originated from crustal rocks. The presence of hornblende, garnet, sphene, and pyroxene in these sediments likely contributed to the presence of rare earth elements ( Table 2). The results presented on the provenance discrimination diagram Cr/V vs. Y/Ni confirm the river sediments' granitic origin. Minor minerals of I-type granites that include porphyry copper, tungsten, and molybdenum deposits include hornblende, sphene, and pyroxene. In addition to copper deposits, porphyry copper deposits contain gold. By comparison, the trace elements associated with gold identified in the Amani River sediments are believed to have essentially identical concentrations of As, Co, Cr, Mn, Ni, Se, Sr, V, and Zn to those reported in the Indus deposits [47].
According to AAS analysis and spatial distribution of river sediments, there is a high concentration of gold on the left bank of the river compared to the right bank of the river. The reason is that the left side of the river has more potential for gold exploration due to low water velocity in point bars and channel bars of the river (Figure 9). Hence, the rivers have two banks. On one bank, it erodes the sediments due to its high velocity, while on the other bank, it deposits the sediments due to its low velocity. The deposition occurs where the velocity sufficiently drops. In the study area, the channel bars were located on the left bank of the river, which deposited the sediments opposite to the erosional bank.
The Indus River passes through the KIA, which is composed of ultramafic and mafic rocks with very unstable high-temperature minerals. These minerals were not identified in the samples, suggesting that they were weathered during transportation.

Conclusions
Based on the petrographic, SEM, and geochemical investigations, the following conclusions are drawn.
According to petrographic studies, the Indus River sediments (which include heavy minerals) are transported from the Himalaya's deformed and uplifted rocks, which are composed of igneous (plutonic and volcanic basic and ultrabasic rock origins) and metamorphic rocks. The mixed source of sediment deposition is also indicated by the elemental composition. The presence of high concentrations of silicon dioxide, iron oxide, and aluminum oxide has been identified. The petrographic investigation also reveals the presence of hornblende, pyroxene, and sphene, which are minor minerals observed in I-type granites. porphyry Cu, Mo, and W deposits are identified in I-type granite. Gold is detected as a byproduct in porphyry Cu deposits. It is determined that these alluvial deposits are mostly the result of weathering and erosion of I-type granites. The trace elements show that the sedimentary bulk in the study area is quite enriched in Au, As, Lu, Sc, Yb, and Zn. The provenance discrimination plotted using geochemical data reveals that both sediments originated from the same granitic source. According to the SEM analysis, the gold grains have a high flatness index and are well rounded and folded. Their surface texture is partially smooth, elongated, and flattened, suggesting a transportation of more than 100 km. The AAS analysis summarizes the feasible areas (C1, C2, and C3) for further investigation of gold deposit economic potential. According to the study, clusters C1, C2, and C3 have higher gold concentrations owing to low water velocity caused by channel bars and point bars compared to clusters C4 and C5, which have a relatively high running-water velocity.
The spatial distribution model reveals that the left riverbank of the studied area has a high concentration of gold resources that may have greater potential for commercial gold exploration than the right riverbank. Overall, the analysis reveals that the research region has high potential for commercially exploiting gold reserves.