Zun ‐ Kholba Orogenic Gold Deposit, Eastern Sayan, Russia: Geology and Genesis

: In this paper, we present a new point of view on the deposit geology and genesis of the largest gold deposit in Eastern Sayan, Zun ‐ Kholba. Quartz–sulfide replacement ores and shallow quartz veins are of great economic importance. At the deposit, quartz–pyrite ore bodies are domi ‐ nant, whereas paragenetically late base metal ‐ bearing quartz veins occur only at shallow levels. The study of the fluid inclusions, stable isotopes (C–O–S), and mineral geothermometry allowed us to determine the P–T conditions of ore deposition. It is established that the temperature of ore for ‐ mation changed from 380 to 433 °C at the deepest levels of the deposit to 316 °C at the shallowest levels. The pressure estimates for gold deposition at 570–950 bar were calculated for the 1490 ‐ m level in the center of the deposit. The determined P–T conditions can help estimate the average depth of deposit formation at about 3.6 km. Ore mineral assemblages were formed from homoge ‐ neous fluids of low to moderate salinity (2.4–7.9 wt.% eq. NaCl). The sulfur isotope composition of sulfide minerals ( δ 34 S = 0–4.6‰), as well as pyrite geochemistry, corresponds to that of older vol ‐ canogenic massive sulfide (VMS) occurrences, which are widespread within the Eastern Sayan oph ‐ iolitic belts. Lens ‐ like fragments of metamorphosed VMS ‐ type sulfide ores are also present in the Zun ‐ Kholba deposit. The oxygen isotope data indicate a metamorphic origin for the ore ‐ forming fluids . Migrating metamorphic fluids may have become enriched in gold, sulfur, and other metals during the flow through the complex ore ‐ hosting lithologies, including ophiolitic bodies with sul ‐ fide ‐ rich VMS fragments that are characterized by a relatively high content of gold and related ore elements. The obtained data allow us to suggest a metamorphic devolatilization model for the gen ‐ esis of the Zun ‐ Kholba gold deposit.


Introduction
Orogenic gold deposits are formed within accretionary and collision orogenic belts.Hypozonal, mesozonal, and epizonal subtypes of such deposits are distinguished by their differences in depth of formation [1].Moreover, they may differ in sources of ore-forming fluids and metals [2,3].
The P-T conditions and genesis of each of these deposit subtypes have been welldiscussed in the recent literature.Most often, orogenic gold deposits do not have any genetic association with magmatism, and deposit host rocks are metamorphosed [4].The origin of orogenic deposits is most commonly explained by the metamorphic or slab devolatilization model [5][6][7].According to this model, gold-bearing fluids are generated from greenschist facies metamorphic rocks during amphibolite facies metamorphism followed by the migration and redeposition of gold.Nevertheless, some orogenic gold deposits may have formed from magmatic fluids [3,8,9].
The Zun-Kholba gold deposit is the largest past producer in Eastern Sayan, having yielded more than 50 tons of Au during past mining operations.However, deposit mining continues to a lesser extent.The Zun-Kholba is considered to be a typical orogenic gold deposit with a high sulfide content [10].
At the earliest publications origin of the Zun-Kholba deposit is assumed to be related to ore-forming fluids that were separated from Sumsunur series granitoids [11].In this case, spatially associated deposits (Pioneer, Barun-Kholba, etc.) are suggested to represent different types of gold mineralization reflecting mineral zoning around a granitoid massif.Later, it was suggested that the main reason for the formation of gold mineralization is the processes of multiple tectonic transformations of rocks [12].This model is based predominantly on the structural observations of the ore bodies.According to an alternative multistage model, ores of the Zun-Kholba deposit are a product of regeneration of Neoproterozoic weakly gold-bearing sulfide ores of submarine volcanogenic sedimentary origin [13].However, actual mechanisms for the ores' formation have not been established.Thus, hypotheses about the genesis of the deposit vary from an intrusion-related to a syn sedimentary with an overprinting hydrothermal activity model.There is no consensus yet.Moreover, features of the deposit geological structure are open to discussion.Ore mineralogy and geochemistry, despite the long-time mining history of the deposit, have been studied insufficiently.Important information about P-T-X parameters of ore formation, as well as stable isotope composition features of quartz-sulfide ores, has not been obtained earlier in detail.
In this paper, we suggest a new point of view on the deposit geology and genesis of the Zun-Kholba gold deposit obtained as a result of geological observations; a mineralogical stable (S, O, and C) isotope; and fluid inclusion studies and also using the materials published by predecessors.

Regional Geology and Tectonics
The Eastern Sayan Mountains form the southern margin of the Siberian Craton and are also located in the northern part of the Central Asian Orogenic Belt.The studied area during this research represents the southeastern part of Eastern Sayan that is also the northern part of the Tuva-Mongol microcontinent, which is the largest tectonic unit of the orogenic belt.The microcontinent is surrounded by ophiolitic sequences and active and passive continental margin rock series.A detailed description of the geological setting of the studied region has been published elsewhere [14].Crystalline basement fragments of the Tuva-Mongol microcontinent form gneissic blocks with amphibolite and migmatite interlayers.The isotopic age of these rocks is about 2900 Ma [14].The Late Neoproterozoic cover of the Tuva-Mongol microcontinent is composed of carbonate rocks with minor shales and sandstones.All parts of ophiolitic assemblages are present, but ultrabasic rocks are dominant.The ophiolites of Eastern Sayan are the oldest ophiolite rocks of the Central Asian Orogenic Belt accreted onto the Tuva-Mongol microcontinent [15].Island arc rocks are represented by metamorphosed volcanic rocks of the Sarkhoy series and schists of the Oka terrane accretionary prism [14].In the southeastern part of the region, terrigenous rocks of a passive continental margin form the Ilchir terrane.All sedimentary and volcanic assemblages are intruded by abundant magmatic rocks that formed at different stages of the tectonic development of the region.
The tectonic evolution of the southeastern part of Eastern Sayan began with the appearance of the Neoproterozoic Paleoasian Ocean about 1 billion years ago and in which primitive island arc complexes developed [14,16].This stage ended about 800 million years ago with the accretion of ophiolites and island arcs to the Archean Gargan continental block, resulting in the formation of the Tuva-Mongol microcontinent.Subsequently, the Sarkhoy and Shishkhid island arcs were formed near the microcontinent margin [17].From about 500 to 420 Ma, the microcontinent collided with the Siberian craton and formed an early part of the Central Asian Orogenic Belt.The early Paleozoic orogeny led to thee formation of most of the orogenic gold deposits in Eastern Sayan [18].In the Late Paleozoic (ca.380-280 Ma), shear deformation occurred throughout much of the Central Asian Orogenic Belt.The deformation events were caused first by collision of the Kazakhstan block with the Siberian Craton and, later, by collision of the East European Craton with the developing North Asian continent [19].Numerous crushing zones in the frame of the Zun-Kholba deposit were formed due to the Paleozoic shear deformations that appeared throughout Eastern Sayan.During the deformations, two parts of granitoid pluton were displaced relative to each other (Figure 1).
The southeastern part of Eastern Sayan in the metallogenic zoning is the Oka ore province [20], which includes some large gold districts (Ilchir, Bokson-Gargan, Oka, and Khamsara) hosting numerous gold deposits [21].The most significant economic orogenic gold deposits are located near the edge of the Archean Gargan block, a part of the basement of the Tuva-Mongol microcontinent and in spatial association with surrounding ophiolite belts.This area is known as the Urik-Kitoi gold ore zone or district [22].This zone includes the largest gold deposit in East Sayan, the Zun-Kholba gold deposit.

Deposit Geology
The Zun-Kholba gold deposit was discovered in 1955 and subsequently explored during a long time period.Mining of the deposit began in 1992 and has continued until the present day.Mining of the deposit is presently nearing completion due to the great depth of the remaining ore.The main geological features of the deposit were described in detail in other scientific papers [11][12][13]22] and unpublished company reports.
The Zun-Kholba deposit is restricted to the Kholba shear zone [23], which also controls some other gold deposits in the ore zone (e.g., Barun-Kholba and Haranur).The deposit is located in a large-scale lens-like zone (see Figure 1) of tectonic mélange.This lenslike structure is similar in shape to a transpressive duplex that is commonly steeply dipping or subvertical [24].
The mélange includes a mixture of granitoids, gneisses, ophiolites, carbonates, black shales, and other rocks that underlie the Zun-Kholba deposit area (Figure 2).These rock fragments are imbedded into finely crushed and altered tectonites (cataclasites).Hydrothermal alterations of many lithologies in the mélange are mostly evident by quartz-sericite zones, well-developed listvenites in the basic or ultrabasic rocks, and widespread silicification.The lamprophyre dike is inferred as a single body at the 1390-m horizon.This dike is intensely deformed and presents lens-like fragments in the ore zones, suggesting a pre-ore to syn-ore emplacement.In contrast, the porphyry dikes cut the ore zones and were emplaced post-ore.
Rare pyrite-pyrrhotite lens-like bodies are observed in the ore-hosting mélange zones as rare boudins.These bodies are analogous to the earlier studied pyrrhotite ores from ophiolites of Eastern Sayan [25].They represent fragments of ancient VMS occurrences that were introduced to the ore field as a part of an ophiolite assemblage.The main ore bodies of the Zun-Kholba deposit represent quartz-sulfide replacement zones and quartz veins with locally as much as 40%-50% sulfides.Descriptions of the ore bodies and ore mineralogy are presented below.

Sampling and Analytical Methods
The Zun-Kholba gold deposit was mined to a depth of more than 1 km by underground operations.We conducted geological observations and collected samples on the 1260, 1290, 1340, 1390, 1440, 1490, 1740, 2032, 2134, and 2250-m levels, as well as from the surface of the deposit (about 2300 m).More than 200 samples of ores and host rocks were taken, which were pieces weighing from 300 g to 1 kg.Geological and structural studies were conducted on the Severnoye, Vavilovskoye, Sulfidnoye, and Dorozhnoye ore bodies.For this study, we collected samples mainly from the quartz-sulfide replacement ores characterized by different ratios of quartz to sulfide.In addition, massive pyrite-pyrrhotite ore lenses were sampled at the 1290-m level.At the surface (2250-m level), both quartz-sulfide replacement zones and sulfide-bearing quartz veins were sampled.
Individual grains of quartz, sulfide minerals, muscovite, and carbonate minerals were hand-picked from crushed ore samples using an optical microscope.
The sulfur isotope compositions of the sulfides were determined by a mass spectrometer (Delta V Advantage dual inlet mode) at the Shared research facilities for Multi-elemental and Isotope Research SB RAS (Novosibirsk).The isotopic composition of sulfur is expressed in δ 34 S notation in permil (‰) relative to the Canyon Diablo Troilite standard, and its analytical precision is about ±0.2‰.
The oxygen and carbon isotopic compositions were analyzed at Analytical Center "Geospectr" of Dobretsov Geological Institute, SB RAS, Ulan-Ude, Russia.The oxygen in the silicates was analyzed using laser fluorination, while the carbon and the oxygen in the carbonates were analyzed using the technique of decomposition of the sample by orthophosphoric acid with the Gasbench option at 60-70 °C for 2-4 h with CO2 extraction and its analysis.In this case, other silicate minerals (e.g., quartz or micas) do not have influence on the analysis results.All the measurements were carried out on a Finnigan MAT 253 mass spectrometer using a double-inlet system for oxygen in silicates and continuous helium flow for carbonates.The measurements were calibrated using international standards NBS-28 (quartz), NBS-30 (biotite) [26] for silicates, and NBS-18 and NBS-19 [27] for carbonates.The error of the obtained values did not exceed 0.2‰ to 0.3‰.
The chemical compositions of the minerals were analyzed at Geological Institute of SB RAS, using a LEO-1430 scanning electron microscope with an attached Inca-Energy energy-dispersion device for quantitative analysis.The lower detection limit of this method is about 0.1 wt.%.For mineral thermometry, the SEM-EDS analyses were converted to atomic percentages, and the relevant parameters (XFeS in sphalerite and NAg in electrum) were determined.
The trace elements in pyrite and pyrrhotite were studied using a New Wave Research UP-213 laser ablation system, coupled with an Agilent 7700x (Agilent Technologies, Santa Clara, CA, USA) plasma mass spectrometer in the South Urals Research Center of Mineralogy and Geoecology of the Urals Branch of the Russian Academy of Sciences (Miass, Russia).The measurements were carried out with an Nd: YAG UV source, frequency quadrupled (wavelength 213 nm) with the fluence settings of 3.0-3.5J/cm 2 , repetition rate 10 Hz, and helium cell carrier gas and a flow rate of 0.6-0.65 L/min.The mass spectrometer settings were as follows: RF Power 1550 W, carrier gas Ar, flow rate 0.90-1.05L/min, plasma gas flow (Ar) 15 L/min, and auxiliary gas flow (Ar) 0.9 L/min.Each analysis was performed in linear mode across the sulfide crystal with a laser spot size of 100 μm and speed of 10 μm/sec.The element contents were calibrated against reference materials USGS GSD-1g, USGS MASS-1, and UQAC-1 using 57 Fe = 46.5 wt.% for pyrite as the internal standard.
The fluid inclusions (FI) in quartz were investigated by thermometry and cryometry.To determine the homogenization temperature, eutectic temperature and ice melting temperatures of aqueous solutions, and temperatures of dissolution of the daughter phases, a Linkam THMSG-600 microthermal camera with a temperature range from −196 to +600 °C was used.The standard instrumental measurement error was ±0.1 in the negative and ±5 °C in the positive temperature range.The bulk salinity of the solutions (eq.NaCl) was determined by cryometry data, according to Reference [28].The salt composition was identified based on the eutectic temperature of the fluid using the data by Borisenko [29].

Sturcture of the Ore Bodies
There are some ore bodies in the Zun-Kholba deposit: Dorozhnoye, Severnoye, Sulfidnoye, Vavilovskoe, and Perevalnoye (see Figure 2).Each ore body can be divided into several parts (for example, Severnoye-1 and Severnoye-2, etc.), which is caused by the inconsistency along the strike due to intense tectonic deformation.All of them are quartzsulfide-mineralized zones that are confined into metasomatically altered cataclasites (tectonites).Near the surface, there are vein and vein-like bodies, whereas ore bodies transform with the depth into mineralized shear zones.The internal structure of the ore bodies is heterogeneous (Figure 3).Quartz-sulfide areas are most often lenticular bodies with sinuous boundaries, merging into larger extended quartz-sulfide zones.Inside the ore bodies, there are also barren areas, "windows", the lengths of which can reach several tens of meters.We studied four ore bodies-Severnoye, Vavilovskoe, Sulfidnoye and Perevalnoye.The Severnoye ore body is located in the northwestern part of the deposit.The ore body has no distinct geological boundaries.It is often determined by sampling results, although sometimes its boundaries are identified by pinching out quartz-sulfide lenses and veins or gold-bearing host rocks.The total length of the ore body reaches 320 m, the thickness varies within 0.5-5 m, and the size increases with the depth.
The Vavilovskoye ore body is located between the Severnoye and Sulfidnoye ore bodies in the central part of the deposit.Below the 1740-m level, it is combined with the Severnoye and Sulfidnoye ore bodies.The length of the Vavilovskoye ore body is 96 m on the surface.With an increase in depth, its length increases to 500 m.The thickness is 0.15-0.8m, with swells up to 4.5 m.
The Sulfidnoye ore body is the largest in the Zun-Kholba deposit.Its size increases with depth from 25 m on the surface (about the 2300-m level) to 600 m at the 1740-m level.Its thickness also increases with the depth from 1.0 to 1.5 m on the upper horizon of the deposit to 5 m on average at 1740 m (horizon of Gallery-12).The ore body is characterized by a regular alternation of swelling and pinching.Moreover, this alternation is observed both along the strike and along the dip.The length of the largest swelling is 130 m, and the thickness is 16 to 17 m.
The Perevalnoye is found only on the upper horizons of the deposit.It is a southeastern continuation of the Sulfidnoye ore body.Its length is 100-125 m, its thickness varies from 1.5 m to 2.0-2.5 m, and in swells, it reaches 8.0 m.It differs from the other ore bodies by a relatively high content of pyrrhotite among the sulfide minerals.
All the ore bodies are steeply (subvertical) dipping and have a lens-like morphology.Near the surface, they are represented by vein-like bodies that are transformed with the depth into mineralized crumple zones composed of a quartz-(carbonate)-sulfide assemblage.The bulk vertical extent of the ore bodies exceeds 1 km.The quartz-sulfide bodies lack clear boundaries and represent the products of silicification and sulfidization of tectonically fragmented and quartz-sericite-altered rocks, with the highest-grade ores formed in silicified and sulfidized limestone blocks (see Figure 3).The sulfide-bearing quartz veins occur only in the upper levels of the deposit, near the current surface.The composition of the ore bodies does not depend on the lithology of any host rock.Vertical zoning of the ores occurred as the base metal sulfides (galena, sphalerite, and chalcopyrite) increased at the upper levels of the deposit.
Previous age estimates for formation of the Zun-Kholba ores used 40 Ar/ 39 Ar dating methods on the tectonites and quartz-sericite-altered rocks.The measurements range from 386 to 354 Ma [18].Most likely, these dates are rejuvenated, since we have no orogenic events at this time, except for the Early Paleozoic orogeny.The problem of reliable determination of the Zun-Kholba deposit age still remains.

Mineralogy of the Ores
Altered host rocks.Ore-hosting rocks at the Zun-Kholba gold deposit have undergone intensive crushing and metasomatic alterations.Wall rock alterations at the Zun-Kholba gold deposit are mainly sericitization, silicification, and sulfidization.Moreover, ultrabasic rocks composing some blocks are listvenitized.These alterations characterize all the rocks that are mostly present as tectonites or cataclasites (e.g., crushed granitoids, gneisses, and ophiolitic rocks) and impure (silicified and sulfidized) limestones.These altered rocks often have flow textures indicating the metasomatic origin of the quartz-sulfide-mineralized zones (Figure 4).Mineral composition of ores.The ore mineral composition of the Zun-Kholba gold deposit has been described in detail by previous workers [11][12][13]22].The main ore minerals comprising the quartz-sulfide ores are presented in Table 1.Our study confirms the previous results, but we additionally identified some minerals such as millerite and vikingite.The most common ore mineral is pyrite.Pyrrhotite, sphalerite, galena, chalcopyrite, tetrahedrite, and native gold and rare arsenopyrite, hessite, native bismuth, scheelite, tetradymite, millerite, and vikingite were also identified.The main mineral assemblage in the quartz-sulfide ores is mainly independent of the wall rock composition.
Quartz-base metal-sulfide (pyrite-chalcopyrite-sphalerite-galena) ores are represented by sulfide-bearing quartz veins and veinlets that occur only in the upper levels of the deposit and in surface exposures.The sulfide mineral content is up to 50% (Figure 5d).The main ore minerals are pyrite, galena, sphalerite, chalcopyrite, and tetrahedrite, with minor pyrrhotite, marcasite, and rare hessite as sporadic micro-inclusions (Figure 6e).Pyrite prevails and forms aggregates of euhedral and subhedral crystals, which are partially corroded by relatively late base metal-sulfides (chalcopyrite, galena, and sphalerite) (Figure 6c,d).This pyrite is further indicated as pyrite2.Marcasite is minor, and it forms anhedral porous grains in association with base metal-sulfides (see Figure 6d).Probably, marcasite is formed as a product of pyrrhotite replacement.Rare pyrrhotite relics are similar in morphology to marcasite grains.Scheelite is present as rare subhedral grains at the ore mineral hosting a quart-sericite aggregate.Base metal-sulfides (sphalerite, galena, chalcopyrite, pyrrhotite, and marcasite) are present as compound assemblages corroding pyrite2 crystal aggregates (see Figure 6c,d).These base metal-sulfide assemblages also include tetrahedrite grains.All minerals of this assemblage are anhedral.Some rare minerals such as hessite, native bismuth, tetradymite, and vikingite form small anhedral lenslike grains and veinlets intersecting the earlier base metal-sulfides-chalcopyrite and pyrite are sometimes rare minerals that form small anhedral grains in quartz.Native gold in the quartz-sulfide replacement ores is present as inclusions of various shapes in quartz and pyrite, often observed along the edges and in cracks of pyrite grains.Gold also forms aggregates with base metal-sulfides (galena, sphalerite, and chalcopyrite).According to chemical compositions, two gold types are distinguished: electrum with a fineness of 550‰-650‰ and medium-grade gold with a fineness of 750‰-850‰ (Figure 7).The medium-grade gold is associated with pyrite-1 (Figure 8a,b), whereas the low-grade gold (electrum) is associated with base metal-sulfides (Figure 8c,d).Additionally, Bi-and Te-bearing mineral assemblages contain low-grade gold, with modal fineness values of about 600‰.The gold composition is independent of the depth.Quartz at quartz-sulfide ores predominantly has a granulate medium-grained microstructure (Figure 9a).Partially, relatively large grains are recrystallized at the grain boundaries where fine-grained quartz aggregates are formed (Figure 9b).Often, quartz aggregates are deformed (Figure 9c).Sulfide minerals are spatially associated with the recrystallized areas, although rarely can be present at the medium-grained matrix (granulated quartz) (Figure 9d).Carbonates and muscovite aggregates are present mostly as veinlets and disseminated grains at the fine-grained recrystallized quartz areas.Accord-ing to the classification of quartz recrystallization mechanisms, the observed microstructure is similar to the bulging recrystallization with beginning of subgrain rotation recrystallization, which occurs at the temperature of about 400 °C [30].Pre-ore massive pyrite-pyrrhotite bodies.These bodies comprise up to 90% sulfides and the main mineral is pyrrhotite (Figure 10a).These ores contain round-shaped globular pyrite and irregular-shaped chalcopyrite as minor minerals, whereas sphalerite, galena and marcasite are rare (Figure 10b).Although the massive pyrrhotite is a pre-ore VMS occurrence, these sulfide boudins are overprinted by gold-sulfide mineralization formed during the main ore of the Zun-Kholba deposit formation.This has led to appearing of epigenetic (regarding to the VMS type relic ore minerals) sulfides (pyrite1, sphalerite, and galena), tellurides (tetradymite and hessite) and native gold.The gold fineness in the pyrite-pyrrhotite bodies is similar to the gold fineness of the quartz-pyrite association which is evidence of the epigenetic nature of this gold.The bodies have modal gold fineness values in the range of 700‰-750‰ (see Figure 7).Appearing of the epigenetic ore minerals is caused by the flow of ore-forming fluids through the pre-ore metamorphosed VMStype pyrite-pyrrhotite bodies.Based on the ore mineral relationships, three ore-forming mineral assemblages (quartz-pyrite, quartz-base metal-sulfide and Bi-telluride) have been identified.Precipitation of the quartz-pyrite assemblage with gold and minor base-metal sulfide occurred at deep levels of the deposit.This assemblage is accompanied by the wall-rock sericitization, sulfidization, and silicification.Some rare minerals, such as arsenopyrite, scheelite, and millerite, as well as relatively medium-grade native gold, were formed within the assemblage.The quartz-base metal sulfide assemblage is characterized by predominance of galena, sphalerite, chalcopyrite.Additionally, in this assemblage, pyrrhotite, marcasite, tetrahedrite, and low-grade native gold were formed.Minerals of this assemblage are particularly observed at the near-surface levels of the deposit.It allows to consider that this assemblage was formed slightly later than the main quartz-pyrite association given that fluid migration occurred up the section as well as with ore deposition temperature decreasing with reducing of the depth.The oldest third assemblage includes a small amount of the Bi-and Te-bearing minerals, such as native bismuth, hessite, tetradymite, vikingite, and low-grade native gold.
All the mineral assemblages were formed within single ore-controlling structure (shear-zone) which suggests single hydrothermal ore-forming system presence, where ore deposition occurred during the decreasing of P-T conditions.As a result, three multi-temperature mineral associations were formed at different levels of the deposit.Nevertheless, some inherent paragenetic associations are distinct and can be used for mineral and isotope geothermometry, such as electrum-sphalerite and arsenopyrite-pyrite pairs.
The bulk of the ore-forming mineral deposition sequence is shown in Table 2.
The distribution of ore-forming minerals in the deposit shows that the appearance of some minor minerals is influenced by the ore-hosting substrate.For example, the lamprophyre dike generates some bismuth, because all Bi-bearing minerals were diagnosed only near the dike, whereas Bi mineralization is absent in other parts of the deposit.Ore bodies hosting by listvenites contain small amounts of Ni-bearing minerals (millerite, pentlandite et al.).Scheelite is present within the ores which are replace the granitoid rocks.This distribution of minerals indicates that a part of the ore-forming components were mobilized from the ore-hosting wall rocks.

Pyrite and Pyrrhotite Geochemistry
Concentrations of trace elements vary significantly, which is reflected in high values of the standard deviation.These variations are due to both the heterogeneity of trace element distribution in the pyrite structure and the presence of micro-inclusions of other sulfide minerals-galena, sphalerite, chalcopyrite, etc.It is known that distribution of trace elements in sulfide minerals is most often heterogeneous, and some elements are concentrated on the surfaces of sulfide grains that make up the mineral aggregate [31].Micro-inclusions of other minerals are clearly observed as peaks in the laser ablation profiles and can be easily excluded from quantitative calculations (Figure 11).Due to the uneven distribution, the trace element concentrations have been averaged (Table 3).This made it possible to observe some geochemistry features of different species of pyrite and pyrrhotite.
Globular pyrite from the pyrite-pyrrhotite lens-like body (pre-ore), subhedral pyrite crystals from the main quartz-sulfide ores (Pyrite1) and from the quartz-base metal-sulfide ores (Pyrite2) have been analyzed.Pyrrhotite from the pre-ore lens-like pyrite-pyrrhotite bodies has been analyzed as well.All the values of element concentrations given in this chapter are average (see Table 3).Pyrite from the main quartz-pyrite ores contains the highest concentrations of the following elements: Bi (49.98 ppm), Ag (50.67 ppm), Mo (0.99 ppm), and Se (5.6 ppm).Gold content is slightly less than in the globular pyrite (1.99 ppm).
A distinctive feature of the pyrite from the quartz-base metal-sulfide ores is high content of As (474 ppm), Zn (1244.7 ppm), Sb (11.93 ppm), and Ni (67.9 ppm).However, this pyrite is depleted in Bi, Te, Au, Ag.Contents of Au (0.65 ppm) and Ag (3.78 ppm) are significantly lower than for the other analyzed pyrites.
Based on the data on pyrite geochemistry, some trends in the concentrations of trace elements can be observed.Thus, from early (pre-ore globular pyrite) to late pyrites, there is a gradual decrease in concentrations of Co, Cu, Zn, Ge, Te, Au, and Pb, while content of As increases.
The Au-As and Au-Cu binary diagrams show the compositions of the analyzed pyrites.According to the data [32][33][34] pyrite composition fields for different types of gold depositsorogenic, porphyry, and VMS are plotted.The Au-Cu diagram shows that contents of Cu and Au regularly decrease from early to late pyrites (Figure 12a).Such trend is especially well distinguished using the average values of the element concentrations (marked with stars in Figure 12a).On the Au-As diagram, plots of all the analyzed pyrites form compact fields also corresponding to the pyrite composition of VMS type deposits (Figure 12b).

Sulfur Isotopes
The results from the sulfur isotope study of the Zun-Kholba deposit ores show that the total range of δ 34 S values varies from 0.0 to +4.6‰ (Table 4).The sulfur isotope composition does not change vertically within the deposit.For pyrite, the values range from 0.2 to 4.6‰, for chalcopyrite from 1.3 to 2.3‰, and for pyrrhotite from 0.0 to 0.2‰.All the obtained values correspond to a deep (mantle) source of sulfur.The sulfur isotope measurements for the Zun-Kholba deposit are almost identical to those from other orogenic gold deposits in the southeastern part of Eastern Sayan (i.e., the Zun-Ospa and Vodorazdelnoe deposits) (Figure 13).All these deposits exhibit a sulfur isotope composition range corresponding to that of ophiolite associated pyrrhotite-rich VMS ores, which are metamorphosed analogues of ancient "black smokers" [25].It is known that "black smokers" contain mantle-derived sulfur.A temperature calculation can be made for co-existing globular pyrite and pyrrhotite using the sulfur isotope ratios (sample Zk-97 and Zk-99-1, see Table 4).The resulting calculation shows a value of 433 °C when based on existing equations [35].This temperature reflects the conditions in the deep part of the deposit during the replacement of pre-ore sulfide bodies (boudins) which was accompanied by isotopic equilibrium for pyrite-pyrrhotite.For this temperature, the sulfur isotope composition of H2S in equilibrium fluid was calculated.All the values fall into a narrow range from −0.6 to +3.4‰, corresponding to meteorite-like (mantle) sulfur.Calculations of fluid sulfur isotope composition values for the spatially associated pyrite2 and chalcopyrite at the near-surface levels (sample Zk-233, 2250 m, see Table 4) shows their nonequilibrium precipitation (chalcopyrite were formed later than pyrite2), although measured δ 34 S values are similar.

Oxygen and Carbon Isotopes
According to the quartz petrography it was established that medium-grained granulate quartz is predominant.Due to the small grains size as well as small amounts of the recrystallized quartz it is impossible to separate samples of these quartz generations.However, according to the articles [39,40], quartz deformation and recrystallization do not affect the oxygen isotopic composition considering that source of the both granulated and recrystallized quartz forming fluid most likely was single.Moreover, small amounts of the recrystallized quartz admixture cannot make a significant influence to the bulk isotopic composition.Therefore, the bulk quartz oxygen isotope composition allows us to identify some features of the oxygen isotopes distribution at the deposit.The δ 18 O values in quartz vary from 12.4 to 17.8‰ (Table 5).A slight decrease of the δ 18 O values with a decrease in depth (for example, levels 1490-1740-1840) is observed for some areas, although this pattern does not apply to the entire deposit.It is probably caused by some degree of fluid-rock interaction with varied lithological fragments within the deposit.Another calculation of mineral formation temperature was completed based on the isotopic compositions of coexisting quartz and muscovite using published equations [41,42].A quartz-muscovite pair was sampled at the deepest level of the mine (1260 m: sample Zk-330, see Table 5).The metasomatic nature of quartz-sulfide ores suggests that quartz and muscovite formation occurred contemporaneously as a result of the same process.The observed petrographic relationship between the quartz and muscovite (sericite) in the analyzed sample proved their simultaneous formation where joint quartz-sericite aggregates have been formed (Figure 14).The calculated value of 420 °C is similar to the temperature of the formation of the coexisting sulfides (433 °C, see above).The oxygen isotopic composition of the ore-forming fluid at the 1260 m level was thus estimated using this temperature and published equations [42].For other levels the temperatures obtained by the mineral geothermometry were used.These temperature values are shown at the chapter 5.6.The bulk range of the δ 18 Ofl values is 6.0 to 13.1, where the near-surface ore has the lowest value (sample Zk-229, see Table 5).
The study of the O and C isotopes from gold-bearing carbonates, which are present as partially silicified and sulfidized limestones, showed δ 13 C values varying from −1.72 to +1.18‰ and δ 18 O values varying from 8.0 to 16.1‰, (see Table 5).A δ 13 C versus δ 18 O diagram shows a shift in the carbonate isotope composition pointing towards mantle values (Figure 15).

Fluid Inclusion Study
The Zun-Kholba deposit is unfavorable for fluid inclusion study, because it contains an extremely low amount of primary fluid inclusions.This is caused by the intensive postore tectonic deformation destroying the majority of the ore-related inclusions (see Figure 9).We studied only 15 inclusions, which were amenable to useful micro-thermometric experiments.However, due to the small amounts of studied inclusions all defined parameters and conclusions can be considered as a preliminary.
The inclusions were found only in grey quartz with granulate medium-grained microstructure from the quartz-pyrite ores from the 1490 m level (see Figure 9a).Therefore, these inclusions were trapped during the early granulated quartz formation.The fluid inclusion study results are presented in Table 6.The studied fluid inclusions have drop-shaped, rounded, and irregular shapes.The size of the inclusions varies mainly from 5-8 microns, with some cases being up to 14 microns.All fluid inclusions are two-phase (vapor + liquid).Homogenization temperatures (Thom) of the inclusions fall into the interval of 168-340 °C.However, the distribution of the values is bimodal, which allows us to distinguish two generations of fluid inclusions differing by their temperatures of homogenization (Figure 16).The homogenization temperatures for the relatively high-temperature mode range from 305-340 °C.These inclusions have even contours and are relatively rare (Figure 17a,b).The majority of the salinity values for these inclusions vary from 2.4 to 7.9 wt.% eq.NaCl, corresponding to low to moderate salinity fluids.
Relatively low-temperature inclusions have a wide range of homogenization temperature values from 168 to 280 °C.They have irregular shape with a sinuous contour (Figure 17c-f).The majority of salinities is also characterized by a large range of values from 0.9 to 9.2 wt.% eq.NaCl.
Eutectic temperatures (Тeut) are similar for the both high-and low-temperature inclusions.The values the Teut vary from −38 to −37 °C, which indicates FeCl2 as the main salt component, probably with an admixture of Mg-, K-, and Na-bearing chlorides [29].
Appearing of the relatively low-temperature inclusions can be caused by the post ore deformations influence.Therefore, these inclusions study data were excluded during the pressure values calculations.Nevertheless, the similar eutectic temperatures allow to assume the genetic relation of both inclusion types.

Mineral Geothermometry
To determine the temperature of the ore minerals formation at the Zun-Kholba gold deposit, we used two mineral geothermometers: electrum-sphalerite and arsenopyrite (Table 7).The electrum-sphalerite geothermometer is based on distribution of sphalerite iron content (XFeS) and atomic amount of silver in co-existing native gold (electrum) (NAg) [44,45].Paragenesis of sphalerite and electrum is determined by mineralogical observations (Figure 18a, see Figure 8c).The geothermometry suggests that the temperature increases with increasing depth (Table 8).The samples from the deepest 1260 m level show an average temperature value of 437 °C.At intermediate depths at the 1490 m level, measurements have an average value of 382 °C, and at the near-surface 2134 m level, the average temperature value is 316 °C.
Arsenopyrite geothermometry is based on experimental studies of the dependence of arsenopyrite composition (S and As content) on temperature and sulfur fugacity in equilibrium with the Fe-S-bearing minerals such as pyrite and pyrrhotite.In the studied quartz-sulfide ores, the pyrite-arsenopyrite assemblage is established as at equilibrium (Figure 18b, see Figure 7b).
Temperature values were determined using the Fe-As-S phase diagram [46].Our calculations are based on the chemical composition of the arsenopyrite associated with pyrite (see Table 8).Average values on all the levels vary from 357 to 393 °C, which corresponds to those of the moderate depth level obtained by electrum-sphalerite geothermometry.However, in this case, a relationship between temperature and depth of sampling is not observed.

Pressure Estimations
The pressure estimations could only be calculated using the high-temperature fluid inclusion data because the low-temperature inclusions had too wide of ranges for homogenization temperature and salinity values.This scatter prevents reliable determination of representative pressure values.
The estimation of mineral formation pressures is based on the average temperature value obtained by mineral geothermometry from the 1490 m level ores, because the fluid inclusions were studied in quartz from this level.The values used for calculating the average temperature are emphasized in bold italics in Table 8.The calculated average temperature is 388 °C.Based on an existing program [47], the pressures were calculated using measured fluid inclusion homogenization temperatures and bulk salinities of the hightemperature fluid inclusions in quartz.Pressure calculations are based on known PVTX properties of the H2O-NaCl system, micro-thermometric data from fluid inclusions, and independent data of the mineral-forming temperature.Obtained pressure values vary in the range of 0.57-0.95kbar (see Table 6).According to the data [48] at a temperature of 388 °C, the critical curve configuration for the FeCl2-H2O system corresponds to the NaCl-H2O system critical curve.Therefore, we can consider the calculated pressures as being close to the true conditions of ore deposition.

P-T Conditions of Ore-Formig Mineral Deposition
Comparison of the oxygen isotope and electrum-sphalerite thermometry results shows their temperature values convergence, reflecting the relatively high-temperature conditions of about 420-430 °C.The similar temperature values were obtained by the sulfur isotope geothermometer using the pyrite-pyrrhotite pair despite the controversy of their association.Temperatures of about 400 °C can be assumed based on the quartz microstructure.This concurrence of obtained data allow us to suggest these values as the most probable ore precipitation temperature conditions at the deep levels of the Zun-Kholba deposit.At the intermediate levels also the consistent temperature values (average value is 388 °C) of electrum-sphalerite and arsenopyrite geothermometers are observed.These values are consistent with the fluid inclusions trapping conditions considering the pressure correction.And the near-surface ores formation temperatures we can estimate using only electrum-sphalerite geothermometer (average value is 316 °C).
Thus determination of the temperature conditions at different levels of the Zun-Kholba deposit shows that the temperatures of ore formation decrease toward the surface.At the deep levels, temperature values range from 382-437 °C.The average temperature value for veins at the surface is 316 °C.Thus, the temperatures are significantly lower at shallower depth, which broadly correlates with the δ 18 Ofl value decreasing to 6‰ at shallow levels, whereas the deeper quartz samples range from 8.4‰-13.1‰.This can best be explained by mixing of meteoric water with the deeper hydrothermal fluids at the shallow depths as it was established for epithermal gold deposits [49].However, it cannot be ruled out that the temperature reduction is caused by cooling of the fluids as they move upward [50].
The pressures of ore formation were determined for the intermediate level (1490 m) of the deposit and range from 570-950 bar.It is known that pressure can be a very variable parameter of an ore-forming hydrothermal system [51].Pressure variations can be caused by changes in hydrostatic pressure due to the flow of the mineral-forming fluid through an inhomogeneous environment represented by rocks with contrasting competencies within a tectonic melange.In such an environment, local areas of pressure build-up may occur, causing variations in fluid pressure during consequential fracturing [52,53].Pressure variations can also be a reason for the heterogeneity of the ore temperatures for the deep samples.
For a rough estimation of possible depth of the ore formation, we can use the highest pressure value of 950 bar.According to the lithostatic gradient (260 bar/km) this pressure value corresponds to the depth of about 3.6 km.The pressures were calculated for the ores sampled at the 1490 m level, which is 800 m below the uppermost level of mineralization at the modern-day surface.Considering that the Eastern Sayan is a mountainous Phanerozoic orogenic belt, the calculated depth of about 3.6 km is close to the true depth of ore formation.These P-T conditions, as well as the depth of ore formation, correspond to those of a mesozonal to epizonal orogenic gold deposit [1,2].
According to the phase diagram for the H2O-FeCl2 system [48], the obtained P-T parameters correspond to those reflecting a homogeneous supercritical fluid.This is also proven by the fact that all the examined fluid inclusions show petrographic evidence of homogeneous trapping.The recognition of FeCl2 as the main salt in the ore-forming fluid is consistent with pyrite being the dominant sulfide in the ore assemblage.Previously, it was established that iron chloride is the predominant salt in fluids forming quartz veins within the pyrrhotite ores from the ophiolitic shales within Eastern Sayan [25].These pyrrhotite ores are widely distributed in the upper volcanosedimentary sequences of the Eastern Sayan ophiolite assemblage and represent metamorphosed fragments of VMS type ores (ancient "black smokers") [25].Ophiolitic rocks, as well as fragments of the massive pyrrhotite ores, are also found in the Zun-Kholba deposit area.It is further evidence of the ophiolitic rocks being involved in the gold ore formation process.

Deposit Genesis
Textures of quartz-sulfide ores show that the ore precipitation occurred due to the replacement of the ore-hosting tectonic melange rocks.A very well-developed quartzsulfide assemblage replaces the limestones.
Due to the uneven distribution of different rock fragments in the ore-hosting mélange, the ore bodies are discontinuous, mostly composed of lenticular zones of quartzsulfide assemblage.This is clearly observed from the morphology of the ore bodies (see Figure 3).Ore bodies have a subvertical extension where the total range of mineralization is more than 1 km.However, they have not yet been contoured in depth.Vertical zoning is occurred in the fact that under near-surface conditions, ores appear enriched in base metal sulfides and quartz-veined zones appear there.All of the above facts indicate the inflow of ore-forming fluids from the deep levels of the deposit.
The C-O isotope study of carbonates also shows the deep-source origin for the oreforming fluid, with additional carbon added from the limestones.These deep-source fluids can be derived from the mantle rocks composing the subducted oceanic crust.Indication of fluid flow events are well observed in the textures of the wall rock alteration zones and in the quartz-sulfide ores (see Figures 4 and 5).Therefore, it can be that one of the main factors for the ore formation is probably a change in fluid chemistry due to fluidrock interaction, which is the result of the metasomatic replacement of the mélange rocks [54].However, in the upper levels of the deposit, sulfide-bearing quartz veins provide evidence for crack-filling processes in the near-surface, as well as for the metasomatic replacement.
The key to indicating the genesis of the gold mineralization is to determine the origin of the ore-forming fluid.This fluid flowed through a major tectonic zone and re-deposited gold and related metals.Igneous rocks occurring in the deposit area are represented by granitoids of the Sumsunur complex.However, their age is Neoproterozoic whereas the gold mineralization is late Paleozoic and thus much younger than the granitoids.Lamprophyre dikes could be syn-gold in age, but their abundance is too limited in scale as to be responsible for the large volume of gold mineralization; only one small, deformed dike is recognized in the deposit.Moreover, it is possible that the lamprophyres were pre-gold.Therefore, there is no connection between ore formation and any magmatic event at the Zun-Kholba deposit.
Oxygen isotope study has shown that the δ 18 O values of the ore-forming fluid (6.0‰-13.1‰)are similar to the values of fluids from many orogenic gold deposits [2].These values correspond to metamorphic water [55].In the shallow part of the Zun-Kholba deposit, the low δ 18 O values suggest addition of meteoric water accompanied ore deposition.This mixing process can also cause a temperature decrease.Nevertheless, the primary source of the ore-forming fluid is dynamometamorphism of the underlying rock assemblages including ophiolites which were involved to the shear-zone.It allows us to suggest a metamorphic devolatilization model as the main ore-forming process.
Zones of high-pressure metamorphism (blueschist belts) trace large suture zones in the southeastern part of the Eastern Sayan [14,23].Because the orogenic gold deposits of the studied region, including the Zun-Kholba, are spatially associated with ophiolite rocks, it can be assumed that relatively high-pressure and high-temperature metamorphism occurred in the deep parts of the Kholba shear zone.Our investigations of pyrrhotite ores from ophiolites allowed us to determine the conditions of metamorphism corresponding to the amphibolite facies [25].According to the mentioned model of metamorphic devolatilization [5], the processes of ore-bearing fluid generation occurs under the conditions of the amphibolite facies of metamorphism.
All analyzed sulfides at the Zun-Kholba deposit have the similar sulfur isotope composition regardless of stage of mineral formation.It is evidence of the single source of sulfur for the deposit.The sulfur isotope values correspond to those described from both massive pyrrhotite-rich VMS ores from ophiolites and from other orogenic gold deposits of the Eastern Sayan (see Figure 13).All orogenic gold deposits in the southeastern part of Eastern Sayan are spatially associated with the ophiolite belt surrounding the Gargan Block.It allows us to suggest that ophiolites, including VMS type ore fragments, are the source of ore-forming components, particularly the sulfur and gold.It is consistent with the increased gold content in the East Sayan ophiolitic rocks [22,56].VMS ores as a one of the sources of sulfur, gold and accompanied elements can explain the high sulfide contents at the Zun-Kholba deposit ores.According to the modern model for the origin of orogenic gold deposit subducted oceanic crust devolatilization is one of the main sources of gold and accompanying elements [6].It explains the spatial association of Eastern Sayan orogenic gold deposits with ophiolite belts [20,21].
Low trace element concentrations in pyrrhotite confirm its metamorphic origin.It is suggested that pyrrhotite occurred due to the metamorphism of primary VMS ores generated by ancient black smokers.As a result, early Fe sulfides were converted to pyrrhotite depleted by trace elements during the phase transition pyrite → pyrrhotite.This mechanism is confirmed by the geochemistry of pyrites in the Zun-Kholba deposit.All the analyzed pyrites correspond to pyrites from VMS type deposits, which is reflected in the Au-As and Au-Cu binary diagrams (see Figure 12).Differences in geochemical characteristics of different pyrite species are due to the evolution of ore-forming elements during the formation of the deposit.Pre-ore globular pyrite is characterized by maximum concentrations of most trace elements, and Cu content is similar to copper concentration in pyrrhotite which proves their genetic relation.Increased contents of Bi and Mo in pyrite1 from the main quartz-pyrite ores are due to the influence of granitoid rocks (including gneisses), numerous fragments of which are present in the ore-hosting mélange.The successive decrease in contents of trace elements from pyrite1 (quartz-pyrite assemblage) to pyrite2 (quartz-base metal-sulfide assemblage) is explained by the crystallization of own mineral phases of these trace elements and their segregation from the pyrite structure [32].In particular, sharp depletion of such elements as Bi, Te, Ag and Pb of pyrite2 is due to the crystallization of a relatively large volume of sulfosalts due to a decrease in the P-T parameters of ore deposition in near-surface conditions.Relatively low-temperature conditions for the formation of quartz-base metal-sulfide ores have been identified based on the data of thermometric studies.
The geological setting of the deposit-hosting lens-like structure shows that ophiolites, as well as fragments of the Tuva-Mongol microcontinent basement and its cover, were added into duplex structures during formation of the Kholba shear zone.These rock fragments were mixed to form a mélange and structurally confined between two parts of a granitoid massif.The generation of metamorphic fluids was caused by dynamic metamorphism in deep parts of the transpressive shear zone.The P-T conditions of dynamic metamorphism in shear zones can reach more than 500 °C and 8.5 kbar [57].These conditions are sufficient for devolatilization of the wall rocks and metamorphic fluid generation [5].Therefore, we consider the Zun-Kholba gold deposit formation to be consistent with the metamorphic devolatilization model.The ore fluids were extracted from deep-seated metamorphic rocks underlying the Urik-Kitoi gold district.These source rocks may be the ancient subducted oceanic crust that was formed at the Tuva-Mongol microcontinent margin.Metamorphic fluids became enriched in gold, sulfur, and other metals during their flow through the ore-hosting environment.This environment consists of rock assemblages containing ophiolites and gneisses, which are characterized by a high gold content [56].Probably the ophiolitic blocks contained significant amounts of VMS type sulfide ores, which provided a source of sulfur and most metals.Moreover, the bulk of the subducted oceanic crust was also relatively enriched in sulfur and some ore-forming elements, including gold [58].The fragments of granitoids, dikes, and ultrabasic rocks contributed some elements that could explain the presence of Bi-, W-, Te-, Ni-, and Co-bearing phases in the epigenetic gold ores.These element enrichments are unusual for the Eastern Sayan orogenic gold deposits [21,36] although they are known to be present in other orogenic gold deposits [7,9,59,60].At a depth of about 3-5 km, the ore formation began.The main factors controlling ore precipitation were probably changes in the chemistry of solutions as a result of water-rock interaction and decreases in the pressure and temperature of the rising fluid.In the nearsurface, some amount of meteoric water was added into the gold-transporting metamorphic fluids.It led to an additional temperature decrease and precipitation of the basemetal sulfides in association with sulfosalts.Low pressure conditions near the surface caused the crack-filling quartz vein formation that hosts the base-metal sulfides.
Tectonic events that led to Eastern Sayan orogeny were caused by the Paleoasian Ocean closure at ca. 500-420 Ma [18].In the late Paleozoic, shear deformation was widespread throughout much of the Central Asian Orogenic Belt including in Eastern Sayan.The Kholba shear zone developed during these tectonic events.The lens-like structure hosting the Zun-Kholba deposit probably was formed as a large transpressional zone.Transpressional shear zones often control the location of orogenic gold deposits [61,62].The rocks of the Tuva-Mongol microcontinent basement and cover, as well as blocks of ophiolites and fragments of granitoids, were sheared together along this lens-like structural zone.All these lithologies within the mélange that hosts the Zun-Kholba deposit were sources for various ore-forming components.

Conclusions
1. Using different independent thermobarometric methods, it has been found that the formation of quartz-sulfide replacement ores in the Zun-Kholba gold deposit occurred at temperatures from 420-433 °C in the deepest part to 316 °C in the shallowest part of the deposit.Pressures during ore formation in the middle part of the deposit were 570-950 bar.The pressure and temperature of the ore formation decreased upwards.2. The determined P-T parameters of ore formation allow us to classify the Zun-Kholba deposit as a mesozonal to epizonal orogenic gold deposit.3. The ores were formed from homogeneous fluids of low to moderate salinity (2.4 to 7.9 wt.% eq.NaCl), where Fe chlorides were the dominant salt.4. The sulfur isotope compositions, as well as pyrite geochemistry, show that the source of some ore-forming elements is ancient fragments of "black smokers" being hosted by ophiolitic blocks.These pre-ore VMS occurrences are scattered in the Zun-Kholba deposit area. 5. Oxygen isotope data prove the metamorphic origin of the ore-forming fluids with some mixing with meteoric waters at the shallow depths.6. Ore formation at the Zun-Kholba deposit is consistent with the metamorphic devolatilization model, where the ophiolites containing sulfide ore fragments and partly host rocks were a source of gold, sulfur, and related ore-forming components.7. The Zun-Kholba deposit was formed during the late Paleozoic deformation caused by the appearance of a regional transpressional shear zone.

Figure 1 .
Figure 1.Regional geological setting of the Zun-Kholba gold deposit.

Figure 3 .
Figure 3. Morphology of the Vavilovskoye and Sulfdinoye ore bodies at the horizon of 1740 m.

Figure 4 .
Figure 4. Thin section photos: (a,b) flow textures in the quartz-sericite-altered rocks, (c) highly sulfidized and silicified limestone, and (d) the flow texture in silicified limestone.Scale bar is 0.2 mm.

Figure 8 .
Figure 8. Native gold morphology: (a,b) medium-grade gold inclusions in pyrite1, (c) low-grade gold in association with sphalerite and chalcopyrite, and (d) low-grade gold in association with galena as an inclusion in pyrite1.Reflected light.Abbreviations: Py-pyrite, Au-native gold, Sphsphalerite, Cpy-chalcopyrite, and Gal-galena.

Figure 9 .
Figure 9. Quartz microstructures: (a) typical granulate medium-grained quartz aggregate; (b) granulate quartz with partly recrystallized fine-grained quartz at the grain boundaries; (c) deformed quartz with both medium-and fine-grained areas; (d) relationships of the quartz and sulfides (Sf).Thin section photos.Scale bar is 0.2 mm.

Figure 11 .
Figure 11.Laser ablation profile in the pyrite2 grain.Small peaks of Zn and Cu (marked by arrows) are probably caused by the occurrence of chalcopyrite and sphalerite micro-inclusions.The pyrrhotite is characterized by low content of trace elements.Most of the analyzed elements are characterized by the concentrations from 0.05 to 11.67 ppm.Only Cu (1250 ppm) and Pb (623 ppm) concentrations are relatively high.In addition, Ge content (11.83 ppm) in pyrrhotite is relatively higher than in pyrites.Compared to the pyrites from the main ores, the pre-ore globular pyrite is characterized by the highest contents of such elements as Co (1390 ppm), Cu (1287.6 ppm), Cr (15.16 ppm), Ge (11.8 ppm), Cd (30.98 ppm), Te (22.44 ppm), Au (2.66 ppm).Pyrite from the main quartz-pyrite ores contains the highest concentrations of the following elements: Bi (49.98 ppm), Ag (50.67 ppm), Mo (0.99 ppm), and Se (5.6 ppm).Gold content is slightly less than in the globular pyrite (1.99 ppm).A distinctive feature of the pyrite from the quartz-base metal-sulfide ores is high content of As (474 ppm), Zn (1244.7 ppm), Sb (11.93 ppm), and Ni (67.9 ppm).However, this pyrite is depleted in Bi, Te, Au, Ag.Contents of Au (0.65 ppm) and Ag (3.78 ppm) are significantly lower than for the other analyzed pyrites.Based on the data on pyrite geochemistry, some trends in the concentrations of trace elements can be observed.Thus, from early (pre-ore globular pyrite) to late pyrites, there is a gradual decrease in concentrations of Co, Cu, Zn, Ge, Te, Au, and Pb, while content of As increases.The Au-As and Au-Cu binary diagrams show the compositions of the analyzed pyrites.According to the data[32][33][34] pyrite composition fields for different types of gold depositsorogenic, porphyry, and VMS are plotted.The Au-Cu diagram shows that contents of Cu and Au regularly decrease from early to late pyrites (Figure12a).Such trend is especially well distinguished using the average values of the element concentrations (marked with stars in Figure12a).On the Au-As diagram, plots of all the analyzed pyrites form compact fields also corresponding to the pyrite composition of VMS type deposits (Figure12b).

Figure 12 .
Figure 12.Binary Au-Cu (a) and Au-As (b) diagrams for the analyzed pyrites.Globular pyrite from the pre-ore pytite-pyrrhotite bodies; Pyrite1-pyrite from the main quartz-pyrite ores; Pyrite2pyrite from the quartz-base metal-sulfide ores.Element concentrations in ppm.

Figure 13 .
Figure 13.Sulfur isotope composition diagram for the Zun-Kholba gold deposit in comparison with other gold deposits of Eastern Sayan and pyrrhotite ores from ophiolitic sequences[25,36,37].Mantle and marine sulfate values from Reference[38].

Figure 17 .
Figure 17.Morphology of the studied fluid inclusions: (a,b)-relatively high-temperature fluid inclusions with even contours; (c-f)-low-temperature fluid inclusions with sinuous contours.The numbers are homogenization temperatures.Scale line size is 10 μm.

Table 1 .
Minerals comprising the quartz-sulfide ores of the Zun-Kholba gold deposit.

Table 2 .
Stages and the sequence of sulfide mineralization formation at the Zun-Kholba gold deposit.

Table 3 .
LA-ICP-MS analysis results for pyrite and pyrrhotite, ppm.

Table 4 .
Sulfur isotope composition of the sulfide minerals.
Note: *-samples for calculating the temperature of the mineral formation.

Table 5 .
Carbon and oxygen isotope composition of carbonates, muscovite, and quartz.

Table 6 .
Fluid inclusion study results.

Table 7 .
Chemical composition of minerals used for thermometry.
Note: in the numerator the range of values, in the denominator-the mean value.