Multi-Objective Optimization for Finding Main Design Factors of a Two-Stage Helical Gearbox with Second-Stage Double Gear Sets Using the EAMR Method

: When optimizing a mechanical device, the symmetry principle provides important guidance. Minimum gearbox mass and maximum gearbox efficiency are two single objectives that need to be achieved when designing a gearbox, and they are not compatible. In order to address the multi-objective optimization (MOO) problem with the above single targets involved in building a two-stage helical gearbox with second-stage double gear sets, this work presents a novel application of the multi-criteria decision-making (MCDM) method. This study’s objective is to identify the best primary design elements that will increase the gearbox efficiency while lowering the gearbox mass. To carry this out, three main design parameters were selected: the first stage’s gear ratio and the first and second stages’ coefficients of wheel face width (CWFW). Furthermore, a study focusing on two distinct goals was carried out: the lowest possible gearbox mass and the highest possible gearbox efficiency. Furthermore, the two stages of the MOO problem are phase 1 and phase 2, respectively. Phase 2 solves the single-objective optimization issue to minimize the difference between variable levels and the MOO problem to determine the optimal primary design factors. To solve the MOO problem, the EAMR (Evaluation by an Area-based Method of Ranking) method was also chosen. The following are important features of this study: First, a MCDM method (EAMR technique) was successfully applied to solve a MOO problem for the first time. Secondly, this work explored the power losses during idle motion to calculate the efficiency of a two-stage helical gearbox with second-stage double gear sets. This study’s findings were used to identify the optimal values for three important design variables to design a two-stage helical gearbox with second-stage double gear sets.


Introduction
One of the most important parts of the drive is the gearbox.It can lower the torque and speed transfer from the motor shaft to the working shaft.Of all the gearbox types, the helical gearbox is the most widely used.This is because the structure of the helical gearbox is straightforward.Its pricing is also reasonable because neither its fabrication nor its design are complex.This is the reason why many scholars are trying to optimize the helical gearbox.
A variety of methods have been used to solve the gearbox MOO problem.Using the NSGA-II (Non-Dominated Sorting Genetic Algorithm II) method, Tudose L. et al. [1] Symmetry 2024, 16, 783 2 of 19 conducted a MOO study for designing helical gears.The goal of the work was to lower both the gearing mass and the flank adhesive wear speed.The MOO of a two-stage helical gear train was solved by R. C. Sanghvi et al. [2] using three different approaches: the MATLAB optimization toolbox, genetic algorithms (GA), and NSGA-II.The optimization of volume and load-carrying capacity were two of the study's goals.The results' comparison indicated that, with regard to both objectives, the NSGA-II approach yielded a better outcome than the other methods.Kalyanmoy D. and Sachin J. [3] carried out a multi-speed gearbox design optimization problem which had four conflicting objectives of design using the NSGA-II technique.It was found from the study that to obtain the same output speed requirement, a larger module is needed for larger delivered power.Also, for low-powered gearboxes, the wear stress failure is more critical than bending stress failure; for highpowered gearboxes, the opposite is true.Edmund S. M. and Rajesh A. [4] used the NSGA-II and the TOPSIS (Technique for Order of Preference by Similarity to Ideal Solution) approach to solve a MOO by taking three objectives into consideration: the gearbox volume, the power output, and the center distance.The study's findings provide insights into the design of small gearboxes.A two-stage helical gearbox was the subject of a MOO by M. Patil et al. [5], with two objective functions: the lowest gearbox volume and the smallest gearbox total power loss.Several tribological and design limitations were used for this investigation.It has been observed that the multi-objective technique reduces the gearbox's overall power loss by half and that solutions derived from single-objective minimization without tribological constraints have a significant probability of wear failure.A. Parmar et al. [6] also used the NSGA-II method to solve an optimization study of a planetary gearbox while accounting for significant regular mechanical and tribological constraints.Utilizing the study's conclusions resulted in a significant reduction in weight and power loss when comparing the outcomes of single-objective optimization with and without tribological limitations.In addition, the method has been applied in [7] to enhance the hypoid gears' operational features and in [8] to reduce the power loss and the vibrational excitation caused by meshing.
An auto encoder and bidirectional long short-term memory (BLSTM) are used in a neural network-based model presented by Sreenatha, M. and P. Mallikarjuna [9] to categorize the state of the gearbox for wind turbines into excellent or bad (broken tooth) condition.To assess the trade-off between three functions-axle stiffness, assemblability score, and overall mass-a MOOP is performed in [10].By creating the Pareto front in this work, a precise and effective trade-off between the gearbox design's objectives may be made, enabling one to choose the optimum gearbox design in a logical manner.A. Kumar et al. [11] conducted a study on optimization of a three-stage wind turbine gearbox with two objectives: minimizing weight and minimizing power loss.In the study, the standard mechanical design restrictions as well as tribological constraints were considered and various synthetic-based ISO VG PAO (Polyalphaolefin) oils were used.It was reported that PAO 320 oil performs better than the other two grades (PAO 680 and 1000).Also, the power loss is significantly reduced with tribological restriction for the selected model.A spur gear set design optimization technique was established by Jawaz Alam and Sumanta Panda [12] to decrease gear weight, contact stress, and ideal film thickness at the contact site.This work combined particle swarm optimization, particle swarm optimization-based teaching learning optimization, and Jaya methods to ensure a significant decrease in weight and contact stress of a profile-modified spur gear set with sufficient film thickness at the site of contact.The study's conclusions show that, compared to traditional designs, the gear design with optimal addendum coefficient values inside the design space is significantly better.G. Istenes and J. Polák [13] conducted research to cooperatively optimize an electric motor and a gearbox in order to construct a drive system for electric automobiles.Reducing the weight of the driving system and total energy waste was the aim of this work.The optimization results were compared with previous research to emphasize the added possibilities of cooperative optimization.It was reported that increasing the gear ratio boosts the system's overall efficiency if the overall drive system is adjusted.The multi-objective design of transmission using helical gear pairs is investigated by Sabarinath P. et al. [14].Gear volumes and the opposing number of overlap ratio are indications of the objective functions.The optimization issue in this study was solved using the Parameter Adaptive Harmony Search Algorithm (PAHS).In [15], an optimal multiobjective study of a cycloid pin gear planetary reducer is described.Using Pareto optimal solutions, the reducer volume, turning arm bearing force, and pin maximum bending stress were examined with the aim of reducing all three of these objectives.According to the study's findings, the updated algorithm can produce Pareto optimum solutions that are superior to those produced by the routine design.In [16], the optimization of tooth modifications for spur and helical gears was solved using a mono-objective selfadaptive algorithm technique.This strategy is based on particle swarm optimization (PSO) technology.The maximal contact pressures and root mean square values of the transmission error signal were improved with the multi-objective optimization.The multi-objective design of transmission using helical gear pairs is investigated in [16].The Taguchi and Grey relation analysis (GRA) methods were recently used by X.H. Le and N.P. Vu [17] to investigate the MOO problem of building a two-stage helical gearbox.Two goals were chosen for this study: the lowest gearbox mass and the highest gearbox efficiency.The study's findings were used to determine the ideal values for the five key design elements that encompass creating a two-stage helical gearbox.In order to maximize the gearbox efficiency and minimize the gearbox volume, the optimal primary design parameters for a two-stage bevel helical gearbox were also determined in [18] using a combination of Taguchi and GRA approaches.Moreover, these methods were applied to solve the optimization of a two-stage helical gearbox with second-stage double gear sets in [19] to increase the efficiency and reduce the mass of the gearbox.
Analysis shows that numerous investigations into the MOO problem of helical gearbox have been conducted up to this point.Power loss in gears has been the subject of numerous studies ( [2,4,5,17,18], etc.).But the study previously stated did not take into consideration the power loss that happens while a gear is idling or when it is immersed in a lubricant during bath lubrication.In addition, a range of methods have been used to solve MOO problems, such as the NSGA-II method [1][2][3][4][5][6][7][8], Parameter Adaptive Harmony Search Algorithm (PAHS) [14], PSO method [16], Taguchi and GRA [17][18][19], etc.Among them, the NSGA-II approach is more frequently employed to solve the MOO problem.Nevertheless, a set of a lot of solutions is typically obtained when the MOO problem is solved using the NSGA-II approach (for instance, 389 Pareto optimum solutions [2]).As a result, to obtain the final results, it is required to combine the NSGA-II approach with another method, like TOPSIS (as in [4]).
While helical gearbox MOO has been extensively studied, MCDM's technique has not been used to find the optimal primary design parameters for these gearboxes.This paper presents the results of a MOO study conducted on a two-stage helical gearbox with double gear sets in the second stage.The two main objectives of this optimization effort are to reduce the gearbox mass and increase the gearbox efficiency.Additionally, the first stage's gear ratio and the CWFW for both stages-three optimal fundamental design characteristics for the gearbox-were looked at.Furthermore, the optimization task was approached using the EAMR method, and the weights of the criteria were determined using the Entropy method.One of the main findings of this research is the suggestion to apply an MCDM technique to solve MOO problems in conjunction with two-step problem solving, tackling single-and multi-objective problems.Moreover, the problem's solutions are more effective than those of earlier studies.

Optimization Problem
In this part, the gearbox mass and efficiency are first calculated in order to build the optimization problem.Next, the specified objective functions and constraints are given.To facilitate calculations, the nomenclature used in the optimization problem are presented in Table 1.Weight density of gear materials ρ g kg/m 3

Calculation of Gearbox Mass
The gearbox mass m gb , is calculated with in which m g , m gh , and m s can be found in detail as follows: (+) Determining m g : in which In the above Equations, i = 1 ÷ 2; ρ g = 7800 (kg/m 3 ) because the material of the gears is steel; e 1 = 1 and e 2 = 0.6 [20]; and a wi can be found with [20] where T 1i (i = 1 ÷ 2) is determined by the following equations: For the gearbox, m gh can be calculated by in which V gh can be found by (see Figure 1) wherein ) in which Vgh can be found by (see Figure 1) wherein In the above Equations, L, H, B1, and SG are calculated by [21]  = ( +  /2 +  /2 +  /2 + 22.5)/0.975 = ( ;  ) + 8.5 •  (18)

(+) Determining m s :
For the gearbox, m s can be determined by where In ( 22), l sj is determined by (see Figure 1) The diameter of the shaft j (j = 1 ÷ 3) can be found by [20] In the above Equations, ρ g = ρ s = 7800 (kg/m 3 ) as the gear and shaft materials are steel; [τ] = 17 (Mpa) [20].

Calculation of Gearbox Efficiency
For the gearbox, η gb is determined by wherein P l can be calculated by [22] P l = P lg + P lb + P ls + P Z0 in which P lg , P lb , P ls , and P zo can be found by (+) Determining P lg : in which where η gi can be determined by [23] In (31), β ai and β ri are found by [23] where f is calculated by the following Equations [17]: (+) Determining P lb [22]: in which i = 1 ÷ 6 and f b = 0.0011 (the radical ball bearings with angular contact were selected) [14].
(+) Determining P s [22]: where i is the ordinal number of seal (i = 1 ÷ 2), and P si can be found by (+) Determining P zo [22]: in which k = 2 is the total number of gear pairs of the gearbox; n is the number of revolutions of a driven gear; T Hi is calculated by [22] T where C Sp = 1 in the case of stage 1 when the involved oil has to pass until the mesh; in another instance (for stage 2) (Figure 2), C Sp can be determined by wherein l hi is determined by [22] In ( 40 in which i = 1 ÷ 6 and  = 0.0011 (the radical ball bearings with angular were selected) [14].
(+) Determining Ps [22]: where i is the ordinal number of seal (i = 1 ÷ 2), and  can be found by (+) Determining Pzo [22]: is the total number of gear pairs of the gearbox; n is the num revolutions of a driven gear;  is calculated by [22]

𝑇 = 𝐶 • 𝐶 • 𝑒
• where  = 1 in the case of stage 1 when the involved oil has to pass until the m another instance (for stage 2) (Figure 2),  can be determined by wherein lhi is determined by [22]  = (1.

Objectives Functions
The MOO problem in this paper has two single objectives: where the vector representing the design variables is denoted by X.There are three primary design factors for a two-stage helical gearbox with second-stage double gear sets: u 1 , X ba1 , X ba2 , AS 1 , and AS 2 .Furthermore, it was shown that AS 1 and AS 2 's maximum values correspond to their ideal values [17].As a result, the three primary design aspects in this work, u 1 , X ba1 , and X ba2 , were chosen as the variables for the optimization problem, and the result is The following limitations must be met by the multi-objective function: Three primary design factors are chosen as variables for the MOO problem, as mentioned in Section 2.3.Table 2 lists these variables along with their minimum and maximum values.In reality, it is challenging to solve the MOO problem using an MCDM technique.The reason is because there are a lot of options or potential solutions when it comes to dealing with a MOO problem.To ensure the accuracy of the parameters and avoid missing the optimization problem's solution, the three parameters in this work have limits, as shown in Table 2, and the difference between variables is 0.02.As a result, the number of options (or experimental runs) that must be determined and compared is (9 − 1)/0.02•(0.4− 0.25)/0.02•(0.4− 0.25)/0.02= 22, 500 (runs).The OMO problem cannot be solved directly with the MCDM method due to the enormous number of options.In order to determine the ideal values for the three primary design variables, the MOO issue in this work was approached using the EAMR method.The two objectives were minimum gearbox mass and maximum gearbox efficiency.To solve the MOO problem for a two-stage helical gearbox with second-stage double gear sets, a simulation experiment was built.Moreover, because this is a simulation experiment, the number of experiments can be raised without a consideration of the budget for each experiment by utilizing the full factorial design.Because there are three experimental variables (as previously specified) and five levels for each variable, the result will be 5 3 = 125 experiments.However, Table 2 indicates that u 1 has the broadest spread among the three specified variables (ranging from 1 to 9).As a result, even with five levels, there was still a significant disparity between the levels of this variable (in this case, ((9 − 1)/4 = 2).To close this gap, reduce time, and improve the accuracy of the outcomes, a strategy for resolving multi-objective issues was proposed (Figure 3).The two parts of this procedure are as follows: phase 1 factors solve the MOO problem to identify the optimal primary design, and phase 2 factors solve the single-objective optimization problem to minimize the gap between levels.Additionally, in the process of addressing the multi-objective problem, the EAMR issue will be rerun using the smaller distance between two levels of the u 1 if the variable's levels are not sufficiently close to one another or if the best answer is not appropriate for the requirement (see Figure 3).ing the smaller distance between two levels of the u1 if the variable's levels are not sufficiently close to one another or if the best answer is not appropriate for the requirement (see Figure 3).

Method to Solve MCDM Problem:
The EAMR technique is implemented in the following stages [24]: - Step 1: Creating the decision-making matrix: where 1 ≤ d ≤ k, the decision maker's number is k, and their indication is denoted by d. - Step 2: For each criterion, ascertain the mean value of each possibility by - Step 3: Determine the weights of creation: - Step 4: Find each criterion's weighted average: - Step 5: Calculate nij using

Method to Solve MCDM Problem:
The EAMR technique is implemented in the following stages [24]: - Step 1: Creating the decision-making matrix: where 1 ≤ d ≤ k, the decision maker's number is k, and their indication is denoted by d.

-
Step 2: For each criterion, ascertain the mean value of each possibility by - Step 3: Determine the weights of creation: - Step 4: Find each criterion's weighted average: - Step 5: Calculate n ij using in which e j is determined by e j = max i∈{1,...,m} x ij (54) - Step 6: Find the normalized weight using - Step 7: Determine the criteria's normalized score: (+) When criteria j is greater as better: (+) When criteria j is smaller as better: - Step 8: Calculate the ranking values (RVs) from G i + and G i − : - Step 9: Calculate the alternatives' evaluation score using The best option is the one with the largest S i .

Method to Find the Weight of Criteria:
In this paper, the Entropy technique was used to establish the weights of the criteria.The actions listed below can be used to put this strategy into practice [25].
-Calculate indicator normalized values as follows: -Determine the Entropy for each indicator as follows: -Find the weight of each indicator as follows:

Single-Objective Optimization
In this study, a direct search strategy was used to solve the single-objective optimization problem.Furthermore, an Excel computer program was created to solve two single-objective problems: reducing gearbox mass and optimizing gearbox efficiency.The following are some of the program findings' figures and observations (calculated with u gb = 20).Figure 4 shows the relationship between η gb and u 1 .It is evident that η gb achieves its maximum value at an optimal value of u 1 .Figure 5 shows how u 1 and m gb are related.When u 1 is at its optimal value, m gb reaches its lowest value (Figure 4).Figures 6 and 7 show the associations between X ba1 and X ba2 as well as η gb and m gb , respectively.These results (Figures 6a and 7a) demonstrate that as X ba1 and X ba2 rise, η gb will fall.However, as X ba1 and X ba2 rise, m gb also rises (Figures 6b and 7b). Figure 8 illustrates the link between the ideal gear ratio, u 1 , for the first stage and the overall gearbox ratio, u t .Moreover, Table 3 displays newly computed restrictions for the variable u 1 based on the outcomes of single-objective problems.

Multi-Objective Optimization
A computer program was created based on the optimization (in Section 2) to carry out the simulation experiment.The gearbox ratios of 10,15,20,25,30,35, and 40 were all included for the analysis.This problem, with ugb = 30, has the answers displayed below.This total gearbox ratio was used for the 125 initial testing cycles (as specified in Section 3.1).The experiment's output values, the gearbox mass and efficiency, will be used as input parameters by EAMR to resolve the MOO issue.Figure 9 illustrates the procedure for determining the optimal major design values when using the EAMR technique.The distance between the two levels of each variable will decrease with each EAMR's step.For instance, in step 1, u1 increases from 4.19 to 4.63 when ugb = 30 (Table 3).As a result, (4.63-4.19)/4 = 0.11 is the distance between the two levels of u1.This procedure will be repeated until there is less than 0.02 separating the two levels of u1.The primary design parameters and output responses for ugb = 30 in the fourth and final iteration of the EAMR experiment are shown in Table 4.The criteria's weights were established using the Entropy technique (see Section 3.3) as follows: First, use Equation (59) to obtain the normalized values of pij.Use Equation (60) to determine each indicator mej's Entropy value.Finally, use Equation (61) to find the weight of the criteria wj.The weights of mgb and ηgb for the most recent EAMR experiment were determined to be 0.4886 and 0.5114, respectively.Guidelines for using the EAMR technique in multi-objective decision making are given in Section 3.2.After that, the decision matrix should be assembled using Formula (50), considering the fact that k = 1 and there is only one result set.Determine the mean of the choices for each criterion using Equation (51), bearing in mind that x = x since k = 1.The average weighted values can then be obtained using Formula (52) while noting that w = w because k = 1.Utilizing Formula (53) and the definition of ej given by ( 54), obtain nij.Next, use Formula (55) to compute vij.Use Equation (56) for gearbox efficiency and Equation

Multi-Objective Optimization
A computer program was created based on the optimization (in Section 2) to carry out the simulation experiment.The gearbox ratios of 10, 15, 20, 25, 30, 35, and 40 were all included for the analysis.This problem, with u gb = 30, has the answers displayed below.This total gearbox ratio was used for the 125 initial testing cycles (as specified in Section 3.1).The experiment's output values, the gearbox mass and efficiency, will be used as input parameters by EAMR to resolve the MOO issue.Figure 9 illustrates the procedure for determining the optimal major design values when using the EAMR technique.The distance between the two levels of each variable will decrease with each EAMR's step.For instance, in step 1, u 1 increases from 4.19 to 4.63 when u gb = 30 (Table 3).As a result, (4.63-4.19)/4 = 0.11 is the distance between the two levels of u 1 .This procedure will be repeated until there is less than 0.02 separating the two levels of u 1 .The primary design parameters and output responses for u gb = 30 in the fourth and final iteration of the EAMR experiment are shown in Table 4.The criteria's weights were established using the Entropy technique (see Section 3.3) as follows: First, use Equation (59) to obtain the normalized values of p ij .Use Equation (60) to determine each indicator me j 's Entropy value.Finally, use Equation (61) to find the weight of the criteria w j .The weights of m gb and η gb for the most recent EAMR experiment were determined to be 0.4886 and 0.5114, respectively.Guidelines for using the EAMR technique in multi-objective decision making are given in Section 3.2.After that, the decision matrix should be assembled using Formula (50), considering the fact that k = 1 and there is only one result set.Determine the mean of the choices for each criterion using Equation (51), bearing in mind that x ij = x ij since k = 1.The average weighted values can then be obtained using Formula (52) while noting that w j = w j because k = 1.Utilizing Formula (53) and the definition of e j given by (54), obtain n ij .Next, use Formula (55) to compute v ij .Use Equation (56) for gearbox efficiency and Equation (57) for gearbox mass to calculate the values of G i .Finally, calculate the S i value using Formula (58).Table 5 shows the outcomes of the option ranking and the EAMR approach's computation of various parameters (for the final run of the EAMR).Out of all the possibilities provided, option 26 is the most ideal one, according to the table.The best values for the main design elements are therefore u 1 = 4.31, X ba1 = 0.25, and X ba2 = 0.25 (see Table 4).
mmetry 2024, 16, x FOR PEER REVIEW (57) for gearbox mass to calculate the values of Gi.Finally, calculate the S Formula (58).Table 5 shows the outcomes of the option ranking and the EAM computation of various parameters (for the final run of the EAMR).Out of bilities provided, option 26 is the most ideal one, according to the table.Th for the main design elements are therefore u1 = 4.31, Xba1 = 0.25, and Xba2 = 0.25     Table 6 shows the optimal values for the main design parameters that correspond to the remaining u gb values of 10, 20, 25, 30, 35, and 40, being a continuation of the previous discussion.The following conclusions can be drawn using the information in this table: The lowest values that correspond to the optimal values for X ba1 and X ba2 are X ba1 = 0.25 and X ba2 = 0.25.This result is also consistent with the observations stated in [20].This is due to the fact that in order to achieve the intended minimum gearbox mass, the coefficients X ba1 and X ba2 must be as small as possible.Lowering these coefficients will result in a decrease in the gear widths (represented by Equations ( 5) and ( 6)) and, in turn, the gear mass (represented by Equations ( 3) and (4)).
Figure 10 shows that there is a definite first-order relationship between the ideal values of u 1 and u gb .Additionally, it was found that the following regression equation (with R 2 = 0.9901) can be used to calculate the optimal values of u 1 : After determining u1, the optimal value of u2 can be determined via the formula below:  =  / (63) To evaluate the model's outcomes for determining the ideal values when calculated using the EAMR method (new method), the findings of this study are compared with those acquired using the Taguchi and Gray Relational Analysis method (old method) in [20].The ideal values of u1 corresponding to different ugb generated by the two approaches were compared and are shown in Figure 11.Additionally, Figures 12 and 13 show the gearbox mass and efficiency data derived from the old and new techniques, respectively.The results presented show that in comparison to the calculations made with the old method, the new approach produces a significantly lower gearbox mass (from 4.9 to 21.6%) and significantly improved gearbox efficiency (from 40.7 to 0.5%) when ugb changes from 15 to 40.After determining u 1 , the optimal value of u 2 can be determined via the formula below: To evaluate the model's outcomes for determining the ideal values when calculated using the EAMR method (new method), the findings of this study are compared with those acquired using the Taguchi and Gray Relational Analysis method (old method) in [20].The ideal values of u 1 corresponding to different u gb generated by the two approaches were compared and are shown in Figure 11.Additionally, Figures 12 and 13 show the gearbox mass and efficiency data derived from the old and new techniques, respectively.The results presented show that in comparison to the calculations made with the old method, the new approach produces a significantly lower gearbox mass (from 4.9 to 21.6%) and significantly improved gearbox efficiency (from 40.7 to 0.5%) when u gb changes from 15 to 40.
After determining u1, the optimal value of u2 can be determined via the formula below:  =  / (63) To evaluate the model's outcomes for determining the ideal values when calculated using the EAMR method (new method), the findings of this study are compared with those acquired using the Taguchi and Gray Relational Analysis method (old method) in [20].The ideal values of u1 corresponding to different ugb generated by the two approaches were compared and are shown in Figure 11.Additionally, Figures 12 and 13 show the gearbox mass and efficiency data derived from the old and new techniques, respectively.The results presented show that in comparison to the calculations made with the old method, the new approach produces a significantly lower gearbox mass (from 4.9 to 21.6%) and significantly improved gearbox efficiency (from 40.7 to 0.5%) when ugb changes from 15 to 40.

Conclusions
The EAMR approach was utilized in this study to solve the MOO problem related to the design of a two-stage helical gearbox with a second-stage double gear set.The study's goal was to identify the best critical design parameters that maximize the gearbox efficiency while reducing the gearbox mass.To carry this out, three essential design components were chosen: the CWFW for the first and second stages, and the first-stage gear ratio.In addition, there were two steps in the MOO problem solution process.Phase 1 was dedicated to solving the single-objective optimization problem of reducing the difference between variable values, whereas phase 2 was concerned with determining the optimal primary design factors.The following findings were drawn from this work: - The single-objective optimization problem speeds up and simplifies the resolution of the MOO problem by bridging the gap between variable levels.-Equation (62) and Table 6 present the optimal values for the three main design parameters of a two-stage helical gear gearbox with second-stage double gear sets based on this study's findings.-Two single targets were assessed concerning the principal design parameters.-By using the EAMR technique repeatedly until the required results are attained, the MOO problem can be solved more precisely (u1 has an accuracy of less than 0.02).

Conclusions
The EAMR approach was utilized in this study to solve the MOO problem related to the design of a two-stage helical gearbox with a second-stage double gear set.The study's goal was to identify the best critical design parameters that maximize the gearbox efficiency while reducing the gearbox mass.To carry this out, three essential design components were chosen: the CWFW for the first and second stages, and the first-stage gear ratio.In addition, there were two steps in the MOO problem solution process.Phase 1 was dedicated to solving the single-objective optimization problem of reducing the difference between variable values, whereas phase 2 was concerned with determining the optimal primary design factors.The following findings were drawn from this work: - The single-objective optimization problem speeds up and simplifies the resolution of the MOO problem by bridging the gap between variable levels.-Equation (62) and Table 6 present the optimal values for the three main design parameters of a two-stage helical gear gearbox with second-stage double gear sets based on this study's findings.-Two single targets were assessed concerning the principal design parameters.-By using the EAMR technique repeatedly until the required results are attained, the MOO problem can be solved more precisely (u1 has an accuracy of less than 0.02).

Conclusions
The EAMR approach was utilized in this study to solve the MOO problem related to the design of a two-stage helical gearbox with a second-stage double gear set.The study's goal was to identify the best critical design parameters that maximize the gearbox efficiency while reducing the gearbox mass.To carry this out, three essential design components were chosen: the CWFW for the first and second stages, and the first-stage gear ratio.In addition, there were two steps in the MOO problem solution process.Phase 1 was dedicated to solving the single-objective optimization problem of reducing the difference between variable values, whereas phase 2 was concerned with determining the optimal primary design factors.The following findings were drawn from this work: - The single-objective optimization problem speeds up and simplifies the resolution of the MOO problem by bridging the gap between variable levels.-Equation (62) and Table 6 present the optimal values for the three main design parameters of a two-stage helical gear gearbox with second-stage double gear sets based on this study's findings.-Two single targets were assessed concerning the principal design parameters.-By using the EAMR technique repeatedly until the required results are attained, the MOO problem can be solved more precisely (u 1 has an accuracy of less than 0.02).

-
The experimental data's extraordinary degree of concordance with the proposed model of u 1 verifies their reliability.

Figure 3 .
Figure 3.The procedure of solving multi-objective problems.

Figure 3 .
Figure 3.The procedure of solving multi-objective problems.

Symmetry 2024 ,
16,  x FOR PEER REVIEW 12 of 19 3 displays newly computed restrictions for the variable u1 based on the outcomes of singleobjective problems.

Figure 6 .
Figure 6.Relation between X ba1 and gearbox efficiency (a) and gearbox mass (b).

Figure 7 .
Figure 7. Relation between Xba2 and gearbox efficiency (a) and gearbox mass (b).Figure 7. Relation between X ba2 and gearbox efficiency (a) and gearbox mass (b).

Figure 7 .
Figure 7. Relation between Xba2 and gearbox efficiency (a) and gearbox mass (b).Figure 7. Relation between X ba2 and gearbox efficiency (a) and gearbox mass (b).

Figure 8 .
Figure 8. Optimal gear ratio of stage 1 versus total gearbox ratio.

Figure 8 .
Figure 8. Optimal gear ratio of stage 1 versus total gearbox ratio.

Figure 9 .
Figure 9. Strategy to find the best main design factors by EAMR.

Figure 9 .
Figure 9. Strategy to find the best main design factors by EAMR.

Figure 10 .
Figure 10.Optimum gear ratio of the first stage versus total gearbox ratio.(The solid line if the values of optimum gear ratio of the first stages with different total gearbox ratio.The dashed line describes the regression equation for that.)

Figure 11 .
Figure 11.Optimum values of u1 calculated by old and new methods.

Figure 10 .
Figure 10.Optimum gear ratio of the first stage versus total gearbox ratio.(The solid line if the values of optimum gear ratio of the first stages with different total gearbox ratio.The dashed line describes the regression equation for that.)

Figure 10 .
Figure 10.Optimum gear ratio of the first stage versus total gearbox ratio.(The solid line if the values of optimum gear ratio of the first stages with different total gearbox ratio.The dashed line describes the regression equation for that.)

Figure 11 .
Figure 11.Optimum values of u1 calculated by old and new methods.

Figure 11 .
Figure 11.Optimum values of u 1 calculated by old and new methods.

Figure 12 .
Figure 12.Minimum gearbox mass values calculated by old and new methods.

Figure 13 .
Figure 13.Maximum gearbox efficiency values calculated by old and new methods.

Figure 12 . 19 Figure 12 .
Figure 12.Minimum gearbox mass values calculated by old and new methods.

Figure 13 .
Figure 13.Maximum gearbox efficiency values calculated by old and new methods.

Figure 13 .
Figure 13.Maximum gearbox efficiency values calculated by old and new methods.

Table 1 .
The nomenclature for optimization problem.

Table 3 .
New constraints of u 1 .

Table 4 .
Main design parameter and output results for ut = 30 in the 3rd run of EAMR

Table 4 .
Main design parameter and output results for u t = 30 in the 3rd run of EAMR.

Table 5 .
Calculated results and ranking of options by EAMR method for u t = 30.

Table 6 .
Optimum values of main design parameters.