Quantitative Estimation of Saline-Soil Amelioration Using Remote-Sensing Indices in Arid Land for Better Management

: Soil salinity and sodicity are signiﬁcant issues worldwide. In particular, they represent the most dominant types of degraded lands, especially in arid and semi-arid regions with minimal rainfall. Furthermore, in these areas, human activities mainly contribute to increasing the degree of soil salinity, especially in dry areas. This study developed a model for mapping soil salinity and sodicity using remote sensing and geographic information systems (GIS). It also provided salinity management techniques (leaching and gypsum requirements) to ameliorate soil and improve crop productivity. The model results showed a high correlation between the soil electrical conductivity (ECe) and remote-sensing spectral indices SI A , SI3, VSSI, and SI9 (R 2 = 0.90, 0.89, 0.87, and 0.83), respectively. In contrast, it showed a low correlation between ECe and SI5 (R 2 = 0.21). The salt-affected soils in the study area cover about 56% of cultivated land, of which the spatial distribution of different soil salinity levels ranged from low soil salinity of 44% of the salinized cultivated land, moderate soil salinity of 27% of salinized cultivated land, high soil salinity of 29% of the salinized cultivated land, and extreme soil salinity of 1% of the salinized cultivated land. The leaching water requirement (LR) depths ranged from 0.1 to 0.30 m ha − 1 , while the gypsum requirement (GR) ranged from 0.1 to 9 ton ha − 1 .


Introduction
Land degradation is one of the world's most severe environmental and socio-economic issues [1][2][3], occurring due to natural phenomena and anthropogenic factors that negatively impact land's ability to function effectively in an ecosystem which causes enormous challenges in achieving sustainable development goals [4][5][6][7]. Degraded lands could reach one-fifth of the total land in some countries [8,9]. Currently, salt-affected soil covers approximately 1.125 billion hectares, with anthropogenic activities affecting 76 million hectares. Soil salinity is a primary challenge to global food security and environmental sustainability. As climate change accelerates, the problem may soon spread to unaffected areas [10]. The high salinity levels could cause adverse effects on soil characteristics and plant physiology [11,12].
There is an urgent need to increase the area of agricultural land to meet the increasing demand for food due to the rapid population growth [13][14][15]. Therefore, one of the effective ways to raise the efficiency of the agricultural unit is land reclamation processes [16]. This helps in fixing one or more defects in the soils that hinder and/or reduce agriculture productivity [17]. However, the traditional methods for reclamation operations are costly in time and effort [16]; therefore, looking to modern technologies to help in these calculations has become an urgent necessity.
The prevalence of saline/sodic soils depends on two types of factors, namely, climatic factors and geomorphologic factors. Saline lands are found in regions with a continental climate or where droughts prevail, which leads to increased evaporation and salt accumulation [58][59][60]. Saline/sodic soils also spread in the lands of lakes, rivers, and sedimentary valleys, and abound in dry and semi-arid areas with little rain and high temperatures. All conditions are identical in the study area where the evaporation process accelerates the formation of salts and their ascent to the surface of the soil through its capillary property [31,32,61,62]. Saline soils have higher salt concentrations than usual, whereas sodic soils have higher concentrations of Na + than usual. Saline soils cause a chemical drought while sodic soils, conversely, cause waterlogging in soils [33]. Leaching is a vital soil management technique applied to salt-affected soil by adding supplemental irrigation water to remove salts from the root zone layers [26][27][28]. Understanding the hydraulic properties of the soil, water mobility, and salt dynamics are essential to correctly conduct the required leaching [63][64][65], while adding gypsum (CaSO 4 × 2 H 2 O) to salt-affected soil is one of the oldest amendment methods. This method promotes the efficient replacement of Na + by exchangeable Ca 2+ leading to the improvement in the soil's physical-chemical and enzymatic properties [66][67][68][69][70][71][72][73].
In Egypt, salinity accumulation, sodicity, and waterlogging are the main form of land degradation. Soil salinity and sodicity seriously affect agriculture production, where saline/sodic soils occupy 46% of the total Nile Delta area [74]. Egypt's croplands are entirely irrigated due to the country's extremely low rainfall and high rates of evaporation. The primary cause of secondary soil salinization in Egypt is the extensive irrigation of agriculture in arid climate conditions [74,75]. Additionally, irrigation with contaminated water from the polluted drains led to increasing in some metals' concentration due to anthropogenic pollution through the spreading of contaminated dredged materials on agricultural fields [76]. The soil salinization problem in Egypt, caused by the reuse of irrigation drainage waters and limits on rice plantings due to the shortage of irrigation water, raises an urgent need for the agricultural productivity of the Nile Delta through, for instance, subsurface drainage in waterlogged lands, land leveling, and use of gypsum amendments [74]. Especially in Egypt, at least 20% of all irrigated areas are salt-affected, and other estimates put the figure as high as 50%. The northern part of the Nile Delta in Egypt contains a huge region of heavy clay soils with shallow open drainage, limited permeability, and low productivity.
In the North Delta region, particularly in Egypt's Kafr El-Sheikh Governorate, there is a serious lack of irrigation water supply. Farmlands at the end of irrigation canals must use available drainage water to compensate for the lack of source of water [76][77][78][79]. Therefore, this study aims to integrate remote sensing and GIS techniques to produce amelioration maps of leaching (LR) and gypsum (GR) requirements in the study area. Landform: The region's topography has a diversity of natural life due to the diversity of environments and the diversity of the topography of the land. The natural environments in the province can be classified into three main types: agricultural and urban environments, coastal environments, and wetlands. Each of them is unique in its animal life, plants, and biodiversity [80,81].
Geology: The center and south of the province cover the sediments of the modern geological age (Holocene era), which are dark-brown formations composed of deposits of clay, clay, and sandy clay. These sediments are deposited over the ancient marine sediments (under delta formations) that date back to the Pleistocene era. They are yellow in color and consist of coarse and fine sand and pebbles consisting of quartz or igneous and metamorphic rocks. The northern coastal zone is a low, sandy coast consisting of soft, brittle sediments belonging to the Pleistocene and Holocene [82,83].
All the ancient geological studies show that the Burullus region in the north of the governorate was less arid than our present era with the presence of many plants. Likewise, the shore of the delta region was mainly composed of silt, with swamps and depressions increasing in it. In the flood season, these depressions were filled with fresh water, Landform: The region's topography has a diversity of natural life due to the diversity of environments and the diversity of the topography of the land. The natural environments in the province can be classified into three main types: agricultural and urban environments, coastal environments, and wetlands. Each of them is unique in its animal life, plants, and biodiversity [80,81].
Geology: The center and south of the province cover the sediments of the modern geological age (Holocene era), which are dark-brown formations composed of deposits of clay, clay, and sandy clay. These sediments are deposited over the ancient marine sediments (under delta formations) that date back to the Pleistocene era. They are yellow in color and consist of coarse and fine sand and pebbles consisting of quartz or igneous and metamorphic rocks. The northern coastal zone is a low, sandy coast consisting of soft, brittle sediments belonging to the Pleistocene and Holocene [82,83].
All the ancient geological studies show that the Burullus region in the north of the governorate was less arid than our present era with the presence of many plants. Likewise, the shore of the delta region was mainly composed of silt, with swamps and depressions increasing in it. In the flood season, these depressions were filled with fresh water, forming a series of small lakes and wetlands. These bogs were filled with organic matter and sediments resulting from the analysis of plant remains, so most of this water was devoid of oxygen. It was also filled with the shells of some bivalve mollusks, especially the cardium type. The coastal area consists of a sandy beach as a result of the sediments that were carried by the waves of the Mediterranean [82,83].
Climate: In general, the climate in Kafr el-Sheikh Governorate is an arid climate (classified as BWh) by the Köppen-Geiger system. The warmest month is August (31 • C), and the coldest month is January (9.4 • C). The total number of rainy days in a year is 31 days, where January is the wettest month while July is the driest month (0.0 mm/0 inches).
A climate diagram ( Figure 2) is based on 30 years of available data from the study area. From this indication of typical climate patterns and conditions of temperature and precipitation, it is clear from the figure that the rain is very little, at less than 25 mm, and most of it occurs in January. Generally, the governorate has a Mediterranean climate, and the temperature varies between 13.2 • C in January (winter) and 26.6 • C in July (summer). The amount of precipitation ranges from 140 mm to 250 mm per year. The winds are generally western and northwest. forming a series of small lakes and wetlands. These bogs were filled with organic matter and sediments resulting from the analysis of plant remains, so most of this water was devoid of oxygen. It was also filled with the shells of some bivalve mollusks, especially the cardium type. The coastal area consists of a sandy beach as a result of the sediments that were carried by the waves of the Mediterranean [82,83]. Climate: In general, the climate in Kafr el-Sheikh Governorate is an arid climate (classified as BWh) by the Köppen-Geiger system. The warmest month is August (31 °C), and the coldest month is January (9.4 °C). The total number of rainy days in a year is 31 days, where January is the wettest month while July is the driest month (0.0 mm/0 inches).
A climate diagram ( Figure 2) is based on 30 years of available data from the study area. From this indication of typical climate patterns and conditions of temperature and precipitation, it is clear from the figure that the rain is very little, at less than 25 mm, and most of it occurs in January. Generally, the governorate has a Mediterranean climate, and the temperature varies between 13.2 °C in January (winter) and 26.6 °C in July (summer). The amount of precipitation ranges from 140 mm to 250 mm per year. The winds are generally western and northwest. Agricultural land and irrigation water: Soil texture in the study area is classified from heavy clay to sandy soil. Surface irrigation systems use the Nile water or drainage reuse, and it has electrical conductivity values between 0.31 and 1.86 dS m −1 .
The soil texture classes of the researched area differ between sandy and heavy clay, according to field surveys and laboratory investigations. Cation-exchangeable capacity (CEC) was strongly associated with clay content and ranged from 7.36 to 44.87 cmolc kg -1 . These soils ranged from being non-saline to being extremely salty according to the salinity levels, which ranged from 0.81 to 10.80 dS m −1 . ESP and pH values ranged from 1.02 to 36.20 and 7.83 to 8.81, respectively. The study area's bulk density and soil depth were between (1.11 and 1.63 Mg m -3 ) and (120 to 150 cm), respectively. Organic matter generally is on average 16.2 g kg -1 . The high temperature in dry and semi-arid locations, which causes the decomposition of fresh residuals, is to blame for the low value of OM. CaCO3 content is 7.30 g kg -1 on average.
The area of agricultural land in the governorate represents about 7.5% of the total agricultural area in Egypt [84][85][86]. Winter rains that fall on the northern coast of the area are unreliable. Groundwater cannot be used due to its excessive salinity as a result of seawater intrusion as well as to limit its effects. The efficiency of the applied surface irrigation system does not exceed 60% [84]. Recently, the governorate's share of fresh Agricultural land and irrigation water: Soil texture in the study area is classified from heavy clay to sandy soil. Surface irrigation systems use the Nile water or drainage reuse, and it has electrical conductivity values between 0.31 and 1.86 dS m −1 .
The soil texture classes of the researched area differ between sandy and heavy clay, according to field surveys and laboratory investigations. Cation-exchangeable capacity (CEC) was strongly associated with clay content and ranged from 7.36 to 44.87 cmol c kg −1 . These soils ranged from being non-saline to being extremely salty according to the salinity levels, which ranged from 0.81 to 10.80 dS m −1 . ESP and pH values ranged from 1.02 to 36.20 and 7.83 to 8.81, respectively. The study area's bulk density and soil depth were between (1.11 and 1.63 Mg m −3 ) and (120 to 150 cm), respectively. Organic matter generally is on average 16.2 g kg −1 . The high temperature in dry and semi-arid locations, which causes the decomposition of fresh residuals, is to blame for the low value of OM. CaCO 3 content is 7.30 g kg −1 on average.
The area of agricultural land in the governorate represents about 7.5% of the total agricultural area in Egypt [84][85][86]. Winter rains that fall on the northern coast of the area are unreliable. Groundwater cannot be used due to its excessive salinity as a result of seawater intrusion as well as to limit its effects. The efficiency of the applied surface irrigation system does not exceed 60% [84]. Recently, the governorate's share of fresh water available for agriculture was about 3.15 billion cubic meters, and agricultural drainage water is mixed with freshwater canals to meet agricultural water requirements [85]. Drainage water with low-quality water such as wastewater is used for irrigation [86], especially in the areas located at the end of irrigation networks that receive inadequate fresh water. There are some main drains in the area such as West El-Burullus, Gharbia, El-Khashaah, Tirrah, and El-Hoks [87]. The principal pollutants are biological oxygen demand (BOD), chemical oxygen demand (COD), and NO 3 -N. While NH 4 -N and NO 3 -N values fall within the normal range for irrigation, they are in the abnormal range according to Egyptian standards. BOD and COD values are rated as bad to moderate and moderate. According to Egyptian standards, the values are within the usual range for irrigation. Furthermore, except for Ni, whose readings are within the normal range, the levels of the heavy metals Cu, Mn, Pb, and Cd are higher than what is permitted for irrigation. B values in water samples range from poor to excellent. In the meantime, irrigation-appropriate pH values ranged from 7.33 to 8.15, EC values ranged from 1.87 to 4.71 ds m −1 , and SAR values ranged from 5.86 to 9.32.

Soil Analysis
Soil sampling was conducted in the study area, where 66 soil samples were collected at 0-0.3 m depths. The samples were dried, grounded, and passed through a 2.0 mm sieve in the laboratory ( Table 1). The soil reaction (pH) and soil electrical conductivity (ECe, dS m −1 ) were identified according to the Page method [87]. The soil organic matter (SOM, g kg −1 ) was determined according to Nelson and Sommers method [88]. The Ca 2+ as carbonate (CaCO 3 , g kg −1 ) was measured volumetrically using a Collins calcimeter method [89]. The exchangeable sodium percentage (ESP) was calculated using the [33] equation: where SAR (sodium adsorption ratio) is a measure of the amount of sodium (Na + ) relative to calcium (Ca 2+ ) and magnesium (Mg 2+ ) in the water extracted from a saturated soil paste. It is the ratio of the Na concentration divided by the square root of one-half of the Ca + Mg concentration. SAR is calculated from the equation: Soils that have values for sodium adsorption ratio of 13 or more may have an increased dispersion of organic matter and clay particles, reduced saturated hydraulic conductivity and aeration, and a general degradation of soil structure.

Soil Amelioration
Leaching requirements (LR, depth cm) were calculated using the [90] equation: where EC iw is the electrical conductivity of the irrigation water and EC e is the soil electrical conductivity. Gypsum requirements (GR, Mg ha −1 ) were calculated using the [33] equation.
where ESP i : actual ESP of the soil; ESP f : ESP required to be reached by reclamation; and CEC: cation exchange capacity (cmol c kg −1 ).

Remote-Sensing Data
Remote sensing provides spatial coverage by measuring reflected and emitted electromagnetic radiation from the earth's surface and surrounding atmosphere over a wide range of wavelengths. Remote sensing implies collecting data without making physical contact with the studied object. This study used Landsat 8 (OLI) images (path 177, row 38) in May 2021.

Image Preprocessing
Image distortions and degradations occur during the acquisition process of remotely sensed images. Preprocessing satellite data are required to remove sensor errors during data acquisition and display the correction, band selection, data dimensionality reduction, and computing complexity reduction. The team conducted radiometric to eliminate radiometric problems in images such as nonuniformity, stripe noises, and defective lines, for proper conversion of digital numbers to reflectance values, geometric, and atmospheric corrections on the studied Landsat OLI images to increase the visual distinction between features.

Atmospheric Correction Using FLAASH Tool
The team conducted atmospheric correction using The FLAASH (fast line/of/sight atmospheric analysis of spectral hypercubes) tool in ENVI 5.1 software to have better reflectance. The team used the native file in a BSQ format for the correction and converted the images to BIL and BIP format to be compatible with the FLAASH tool.

Surface Interpolation Using the Ordinary Kriging Technique
The team used the interpolation method to determine the spatial variability and pattern of the soil characteristics in two-dimensional soil data sets in the topsoil. The geostatistical analyst extension (Arc GIS 10.4.1) [91] was used to develop the semi-variogram between each pair of points and interpolate between the sampling locations using the kriging method to predict the soil salinity in the study area. Ordinary kriging was used to estimate the value of continuous soil salinity (z) at an unsampled location (u) using only data on this characteristic [z(u α ), α = 1, n] as a linear combination of neighboring observations: The ordinary kriging weights were chosen to minimize the estimation or error variance, The weights were obtained by solving a system of linear equations: To ensure the estimator was unbiased, constraining the weights to sum to one requires the definition of the Lagrange parameter m (u).

Soil Salinity Indices
The team examined fourteen different spectral salinity indices related to salt detection and soil salinity mapping developed in numerous studies. The most commonly used salinity indices taken into account in this study (NDSI, SI A , SI 1, SI 2, SI 3, SI 4, SI 5, SI 6, SI 7, SI 8, SI 9, NDVI, SAVI, and VSSI) are presented in Table 2. Where: B, G, R, NIR, SWIR1, and SWIR2 refer to the reflectance in visible blue, green, red, near-infrared, Shortwave infrared 1, and 2, respectively.
The processing steps of mapping soil salinity using Landsat 8 image by the superior index among the used indices through assessing soil salinity from soil samples are shown in Figure 3. Firstly, FLAASH model was applied to remove the atmospheric effects [98][99][100]. Then, image processes were applied, i.e., image morphology, conversion from digital number to reflectance value, cloud filtering [101], and image enhancement. Subsequently, indices were computed and analyzed. Then, indices were normalized in Excel software. Secondly, the soil samples were analyzed with the spectral reflectance of the image. The soil salinity is estimated by the measured laboratory EC. Based on the results, the relationship was determined between reflectance values and indices of soil salinity to estimate the soil salinity from the image. It was noted that various soil types reflect solar radiation differently. The variation in reflectance makes it possible to identify the type of soil at the surface layer. Validation samples were taken from different land use/land cover types, including Sabkha, water bodies, waterlogged, bare soil, and cultivated land. The sample locations are selected at different salinity intrusion degrees. Finally, leaching water requirements and Gypsum requirements were calculated as shown in Figure 3. soil at the surface layer. Validation samples were taken from different land use/land cover types, including Sabkha, water bodies, waterlogged, bare soil, and cultivated land. The sample locations are selected at different salinity intrusion degrees. Finally, leaching water requirements and Gypsum requirements were calculated as shown in Figure 3.

The Relationship between ECe and Remote-Sensing Spectral Indices
Various spectral indices derived from the initial Landsat bands in the study area validated the developed spatial model of soil salinity; Figure 4. The statistical correlation between soil electrical conductivity (ECe) and remote-sensing spectral index revealed that the salinity index (SIA), salinity index 3 (SI3), vegetation soil salinity index (VSSI), and salinity index 9 (SI9) had a significant correlation with ECe (R 2 = 0.90, 0.89, 0.87, and 0.83, respectively). However, salinity index 5 (SI5) had a low correlation (R 2 = 0.21). The models with the highest R 2 values, indicating a high correlation between field measurement data and satellite data, were chosen as the best regression model to produce the soil salinity map of the study area. Overall, the brightness index with bands (R and NIR) of the image dated May 2021 had the highest correlation of 90%. Therefore, this obtained regression equation was used for soil mapping, while the density-slicing method was used to classify the different salinity levels, according to the different salinity classes. These salinity classes were defined using the international salinity thresholds.
The SIA, SI2, SI3, SI4, SI7, SI8, and SI9 indices are positively correlated between the actual ECe and the modeled ECe, and negatively correlated with NDS1, SI6, and SI5. All of the studied indicators followed a normal distribution for the low-salinity class (2 and 4 dS m −1 ), while the higher-salinity class resulted in negative skewness. It was noted that there was a high level of uncertainty and variability for all indicators with higher salinity levels, but a lower level of uncertainty with lower salinity content (Figure 2).

The Relationship between ECe and Remote-Sensing Spectral Indices
Various spectral indices derived from the initial Landsat bands in the study area validated the developed spatial model of soil salinity; Figure 4. The statistical correlation between soil electrical conductivity (ECe) and remote-sensing spectral index revealed that the salinity index (SI A ), salinity index 3 (SI3), vegetation soil salinity index (VSSI), and salinity index 9 (SI9) had a significant correlation with ECe (R 2 = 0.90, 0.89, 0.87, and 0.83, respectively). However, salinity index 5 (SI5) had a low correlation (R 2 = 0.21). The models with the highest R 2 values, indicating a high correlation between field measurement data and satellite data, were chosen as the best regression model to produce the soil salinity map of the study area. Overall, the brightness index with bands (R and NIR) of the image dated May 2021 had the highest correlation of 90%. Therefore, this obtained regression equation was used for soil mapping, while the density-slicing method was used to classify the different salinity levels, according to the different salinity classes. These salinity classes were defined using the international salinity thresholds.
The SI A , SI2, SI3, SI4, SI7, SI8, and SI9 indices are positively correlated between the actual ECe and the modeled ECe, and negatively correlated with NDS1, SI6, and SI5. All of the studied indicators followed a normal distribution for the low-salinity class (2 and 4 dS m −1 ), while the higher-salinity class resulted in negative skewness. It was noted that there was a high level of uncertainty and variability for all indicators with higher salinity levels, but a lower level of uncertainty with lower salinity content (Figure 2).

Land Use
The land use in the study area was 373,191 ha and can be classified into four dominant classes: cultivated land, water bodies and lake Burrulus, fish ponds, and urban area. The cultivated land was the main class, the second class was water bodies and lake Burrulus, the third class was fish bonds, and the fourth class was the urban area, which covered about 72, 12, 10, and 6% of the total area, respectively (Table 3).

Soil Quality Index (SQI)
The results related to classifying the different salinity levels by the salinity index SIA with bands (R and NIR) are given in Table 4 and Figure 5. The results of the proposed model revealed that the assessment of salinity levels was classified into four classes: the low salinity (4 > dS m −1 ) class occupies 118,580 ha (44% of the cultivated area); the moderate-salinity class (4-8 dS m −1 ) occupies 73,177 ha (27% of the cultivated area); the high-salinity class (8-16 dS m −1 ) represents 77 ha (28% of the cultivated area); and the extreme-salinity class (>16 dS m −1 ) represents 145 ha (1% of the cultivated area). The results indicated that the salt-affected soils in the study area represent 56% of the cultivated land.

Land Use
The land use in the study area was 373,191 ha and can be classified into four dominant classes: cultivated land, water bodies and lake Burrulus, fish ponds, and urban area. The cultivated land was the main class, the second class was water bodies and lake Burrulus, the third class was fish bonds, and the fourth class was the urban area, which covered about 72, 12, 10, and 6% of the total area, respectively (Table 3).

Soil Quality Index (SQI)
The results related to classifying the different salinity levels by the salinity index SI A with bands (R and NIR) are given in Table 4 and Figure 5. The results of the proposed model revealed that the assessment of salinity levels was classified into four classes: the low salinity (4 < dS m −1 ) class occupies 118,580 ha (44% of the cultivated area); the moderatesalinity class (4-8 dS m −1 ) occupies 73,177 ha (27% of the cultivated area); the high-salinity class (8-16 dS m −1 ) represents 77 ha (28% of the cultivated area); and the extreme-salinity class (>16 dS m −1 ) represents 145 ha (1% of the cultivated area). The results indicated that the salt-affected soils in the study area represent 56% of the cultivated land.   Figure 6 shows the different leaching requirements that should be added to the soil to reduce soil salinity. The different leaching water requirement depths were classified into six classes: (1)

Discussion
Assessment of salt-affected soil using remote sensing and GIS is beneficial due to its low cost and efficiency. This will improve the management of the salt-affected soil [1]. It was clear from the results obtained that using Landsat images can capture soil salinity with a significant correlation between the ECe values and bands of the Landsat images [40][41][42][43][44][45][46].
Our results indicate that the correlation between the remote-sensing spectral index and ECe (salinity index (SI A ), salinity index 3, vegetation soil salinity index, and salinity index 9) was highly significant. This agrees with the views of [102,103] who emphasized that the salinity index (SI) has the highest correlation with soil salinity based on the image enhancement method. Elhag [104] indicated that the SI-3 and SI-9 have a high correlation with soil salinity indices.
The results showed that the salt-affected soils in the study area represent 56% of cultivated land. These results agree with one study [80,93], which stated that more than 50% of the soil in Kafr El-Sheikh Governorate suffers from land degradation. Additionally, good or non-saline soils in the study area decreased by 33% during the period 1961 to 2016 [81]. Another study conducted by Enar [105] indicated that the low-salinity soil increased by 0.46%, while moderate salinity, high salinity, and extreme soil salinity increased by 16%, 52%, and 20% during the period 2000 to 2020, respectively.
The added value of the paper is in mapping the soil water leaching and gypsum requirements using remote-sensing and GIS techniques. Limited studies have covered this topic so far. The method used to calculate the leaching water requirements (cm, depth) and gypsum requirements (GR, Mg ha −1 ) according to the concentration of salts is reliable and accurate [33,90]. The leaching water depths required to reduce the ECe ranged between 0.01 and 0.90 m ha −1 , while the gypsum required to reduce the initial ESP in different study zones ranged from 0.1 to 9 tons ha −1 .
The investigated salt-affected soils are formed as a result of climate and inappropriate soil management. This is in addition to the effect of irrigation water, water logging, and saline water intrusion of the Mediterranean. Saline, saline-sodic, and sodic soils have a strong presence in the area with an average of 55% of the total cultivated soils ( Table 2). The south part of the area is threatened by sodicity according to the low-salinity soils and highly carbonated irrigation water, while the north of the area contains the highest area of saline and saline-sodic soils, reaching 33%. Poor drainage in addition to reuse of saline drainage water supports the buildup of salinity and sodicity [106] The most popular method for reclaiming salt-affected soils in the region is a gypsum amendment (CaSO 4 2 H 2 O) combined with intermittent leaching. Another two ways for adapting and mitigating salinity and sodicity accumulation in the region are furrow irrigation and rice production under ponding.
The salts are spread in the soil profile, especially in the northern areas of the study area, adjacent to the water-logged areas, Sabkha, and along the coastline. The dominant salts in the delta are saline, and sodic soils are sodium sulfate (Na 2 SO 4 ) and sodium carbonate and bicarbonate (Na 2 CO 3 and NaHCO 3 ). The solubility of these salts decreases sharply with temperature decreases; accordingly, the reclamation and leaching processes should be applied during the summer warm season only. Improving drainage and preventing industrial and sanitary wastes in the agricultural drain is a must [107]. Land degradation in coastal areas, increased distribution of soil salinity, and reduced crop productivity in the region are the manifestations of climate change that have already appeared in the region from rising sea levels, coastal erosion, reduced Nile flow, increased summer temperature, changing rainfall patterns [108][109][110][111][112], and increased evapotranspiration [113].
In the study case, saline soils should be treated, and subsequently sodic soils, in order to reduce the concentration of salts to the appropriate degree for the growth of plant roots and even the appropriate depth for the roots [114][115][116][117][118][119][120].
Proper agricultural practices should be followed such as: adding organic fertilizers, developing and maintaining drainage, following an appropriate agricultural cycle, using a digger plow, and choosing salt-tolerant crops and an appropriate irrigation system. Nitrate, phosphate, and potassium fertilization increase the resistance of plants to salinity. Salt-tolerant crops such as barley and sorghum are the most salt-resistant cereal crops, followed by rice and wheat, while maize is the least resistant. Cotton and sugar beet are the most important salt-tolerant crops, while sugar cane, fava beans, and peas are the least tolerant of salinity. Most vegetable crops are moderately resistant to salinity, while most fruit crops, especially deciduous, are sensitive to salinity [114][115][116][117][118][119][120][121][122][123][124].

Conclusions
The physico-chemical characteristics of 60 soil profiles were investigated. The results showed remarkable differences among various sites. The differences were very clear between the southern regions, where they are often affected by a slight or medium degree of deterioration and are often concentrated in soil compaction, while the northern regions were greatly degraded due to the presence of most types of soil deterioration such as salinity, alkaline, and waterlogging. The GIS, Landsat OLI satellite images, and multi-temporal satellite image analysis were used to estimate the rate and extent of salinized areas. These proven tools are handy for providing accurate and timely geospatial information depicting soil conditions. The results reflected that 56% of cultivated land of the Kafr El-Sheikh Governorate suffers from salinization. Zoning or classifying the area into zones can lead to better management and amelioration of the different salinity zones. Therefore, using this technology improves the management of salt-affected soil on a large scale and can be regarded as one of the best management strategies for increasing crop production. The causes of salinity in investigated soils are thought to be a result of seawater intrusion-especially in the coastal zone of the area-high water table level, accumulation of salt in the upper soil layers due to unsuitable irrigation management, and inadequate drainage conditions. Salinity problems require sustainable management strategies, including identifying and further developing crop cultivation practices adapted to saline conditions, enhanced drainage systems, using salt-tolerant varieties/crops, and exchanging knowledge and transferring practical and adaptive solutions. Water is fundamental in agriculture; different sources of pollution such as sewage and industrial wastewater are discharged onto the drains. So, the water in this drain has very low quality, which in turn may cause hazards to soil and grown crops. It could be concluded that drains may be used for irrigation purposes under controlled precautions with good soil management, e.g., good tillage, deep plowing, land leveling, applying soil and water amendments, and finally a suitable cropping system.