Establishing Regional Power Sustainability and Feasibility Using Wind Farm Land-Use Optimization

: Wind-farm planning optimization is important for decision-making concerning regional energy planning in developing countries. This process is governed by restrictions on site selection based on land suitability metric variables, wind turbine technology variables, and land-use governing criteria. This study aims to create a framework for land appropriation strategies for locating optimum sites suitable for wind farms. It is using Jordan as an Area of Interest (AOI), where the scope is to illustrate how this framework will employ wind turbine energy to positively enhance the national Gross Domestic Product (GDP). The methodology employs thirteen GIS thematic layers with a 250-m spatial resolution to substantiate how site-speciﬁc criteria, turbine type, and turbine hub height variables are determining factors in the optimal solution. This method involves selecting relevant factors, database construction, data layer generation and preparation, numerical ranking and weighting of each factor, and computation of the potential wind farm locations map by overlaying all the thematic GIS layers. The results showed that the establishment of wind farms would not only meet the AOI’s growing energy needs, rather exceed them to generating income for the developing nation. The results of the feasibility study will boost the national GDP by 3.4%; where, for example, one governorate alone could produce 274.3% of the total required national consumption at a turbine hub height of 50 m. The study attests to a valuable framework that can be implemented elsewhere to establish regional power sustainability and feasibility for other nations. The results show that an added land-use layer indicating the potential value of land in terms of its suitability for establishing wind farms should be considered in future sustainable regional planning studies when considering networks for smart cities, industrial cities, smart agriculture, and new agglomerations.


Introduction
Affordable energy resources are the primary motivation for enabling, enhancing, and activating economic forces around the world and are therefore considered key elements for sustainable socio-economic development [1]. In 2020, The International Renewable Energy Agency (IRENA) declared that by the end of 2018, renewable energy accounted for 26% of the total electricity generation (10% from wind). It predicted that this would continue to rise globally to an expected 60% (36% from wind) by 2050 [2].
Sustainable development is now a priority in governments' agendas where more attention is given to the need for innovative scenarios, coordinated actions, and policies on developing the contributions of renewable energy [3,4]. Therefore, decision-makers must reconsider the methods used to grant energy sustainability, especially in terms of smart cities, industrial cities, smart agriculture, and new agglomerations while preserving agricultural lands and restricting urban growth [5,6]. Governmental plans can no Land 2021, 10, 442 2 of 32 longer separate energy planning from spatial planning [7,8]. The latter is responsible for state space and its use by the community, the stakeholders, and the developers under the umbrella of integrated sectoral policies that promote development and innovative actions [9]. Now, every region should follow a systematic framework for analysis that meets its energy needs from renewable resources [8,10]. An energy planning attempt involves finding a set of sustainable resources at micro and macro levels to optimally meet the energy requirements/demands of all tasks occurring at the centralized or decentralized levels [11][12][13].
Building a road map for renewable energy systems and land-use/landcover classification based on locally available resources at a regional scale will create the right climate that allows communities to find an appropriate framework of living, which provides comfort and welfare in cities. Renewable energy is an essential factor for societies to meet future demands for energy challenges to achieve the desired structure for their lives [14]. Energy is the infrastructure and the main factor for residential, industrial, and commercial activities. Thus, it requires decentralized energy planning approaches that secure wellbeing in both remote and near areas based on renewable energy availability. Land-use/land-cover classification criteria should constitute a renewable energy potential and suitability. It is expected that this new planning system that accounts for renewable energy will support and provide high-efficiency decision-making policies to facilitate sustainable economic growth and create smart cities, industrial cities, new agglomerations, smart agriculture, and a new communication network [11,15,16].

The Importance of Renewable Energy
Due to the environmental impacts of non-renewable energy and limited reserves, renewable energy is increasingly approached as an essential solution. There are several options for the type of renewable energy; however, determining factors such as environmental impacts, cleanliness, cost, stability, and efficiency also play a role in determining the type of energy [17][18][19]. The most appealing criterion in renewable energy is its reliable and stable supply of clean and environmentally friendly energy [17,18]. The use of renewable energy becomes more important in countries with a limited-to-no supply of local fossil fuels. Consequently, importing fossil fuels in large quantities for supplying everyday energy needs becomes prohibitive for citizens also required to purchase their daily food and needed services.
Renewable energy costs are dependent on the cost of infrastructure and maintenance fees [17,18]. Thus, it is independent of international fluctuations in fossil fuel prices [17,18]. Because of improving technologies and increased competition between supply providers, the cost of energy derived from wind, solar, biomass, and geothermal sources is declining [17,18].
It has been shown that income, energy use, economic growth, and human quality of life are positively correlated [20]. Therefore, the nature of renewable energy can lead to improvements in economic growth and sustainable development, which in most cases, can lead to increased income and better life quality [19]. The more the economy grows, the more demand is placed on energy. Especially in developing countries with limited resources, to sustain economic growth, it is also advantageous that energy be renewable [17][18][19]. Renewable, clean energy can grant opportunities for income generation, improved services, and improved agriculture. Decision-makers often encourage the use of renewable energy by providing tax cuts and flexible investment strategies for individuals and business entrepreneurs [19,21]. Despite the availability of fossil fuels, many countries such as Iran made efforts to reduce tariffs on wind energy and increase the prices of fossil fuels and electricity made depending on it to encourage the use of wind energy [22]. In the end, energy is essential for development where lower and stable renewable energy prices can help to create a more feasible business, thus providing more job opportunities and more capital, especially in developing countries [17][18][19]. Based on the global changes the world has witnessed, especially after the spread of the global pandemic of COVID-19, many cities have been isolated from each other. The pandemic has shown the urgent need to make energy readily available at remote sites and to create self-sufficient urban agglomerations [23]. Available energy will prevent the migration of people to major cities, thus complying with the new concept of spatial distancing. In many land-locked developing countries, urban agglomeration leads to urban sprawl, which is often concentrated on agricultural lands. They also suffer increased unemployment. Other remote places with less rainfall are not urbanized due to the inability to succeed in agricultural projects. By providing energy to remote places, we can protect agricultural lands that grant our food security thus, preserving fertile lands in rain-fed areas to protect them from urban sprawl [10,15,16]. The remote places (if equipped with renewable, costefficient energy) can house other investments, smart projects, and manufacturing facilities that can create job opportunities for the growing population. Especially in developing countries, policies that are made to sustain access to renewable energy are a major energy goal. This access to energy in rural and remote areas will ensure the protection of existing agricultural lands and allow the reclamation of less valuable lands by providing water for irrigation, establishing agricultural economic projects, and providing a protected climate for these crops. In the end, the goal is achieved by granting food sufficiency [24].

Wind Energy
Due to the enhanced technologies of wind turbines, wind energy is now more feasible than ever and is used widely offshore and inland around the world [17,19]. There are several opportunities with wind energy, such as socioeconomic development, accessibility of energy in remote places, and reliable energy security [19]. Wind energy projects are now intercountry cooperative establishments. For example, America is benefiting from Canadian wind projects, which support energy use in large cities such as New York [25,26]. The North Sea region energy project for 2050 is another example of intercountry cooperation that is expected to cover about 89% of the required electricity for England, Belgium, the Netherlands, Denmark, and Norway [27].
One key aspect of the availability of wind energy is the role of technological development in making this a sustainable solution. In other words, if there are no technological investments (mega-projects) in agriculture, manufacturing, technology, and services, the use of wind energy for housing alone is not feasible. Especially, when we want to develop the economy in a new region, technological development plans must precede the renewable energy projects [28]. If a remote region has a great potential for generating wind energy, it is then an important opportunity to create the type of technological mega-projects that will benefit from the energy infrastructure in that place. This idea is novel, especially when many are suffering unemployment and when the urban areas are sprawling onto the agricultural lands, such as the case of Jordan, Egypt, Syria, Iraq, and Sudan. It becomes a necessity to draw some of the population seeking job opportunities to other potential places. This will protect agricultural lands for future generations and create opportunities for manufacturing in other remote places where energy is affordable and making the investments feasible.
According to the World Wind Energy Association (WWEA) (2019) [29], wind power capacity around the world had reached 597 GW by the end of 2018, identifying China and the United States of America as leading countries with an accumulated wind capacity of 221 GW and 100 GW, respectively [30,31]. According to the WWEA, all wind turbines installed by the end of 2018 provided around 6% of the global electricity demand [29]. Swedish Wind Energy Association is targeting 100% renewable electricity by 2040 through wind power to combat climate change and improve competitiveness [32].
Because of its reliability, resilience, feasibility, and affordability, wind energy is one of the most commonly harvested renewable energy sources [22,33]. Selecting the best location for wind farms requires an examination of its environmental, social, economic, and technical limitations with variable methodologies [22,34,35]. It is the role of policies to balance between the needs of national goals and their environmental concerns [36]. Restrictions affecting potential wind turbine sites include low wind speed and land-use/land-cover limitations (i.e., urban areas, protected areas, and areas far from energy-consuming urban agglomerations) [34,[37][38][39].
A critical challenge is to reinvent a comprehensive planning system to achieve sustainable energy-balanced regions [40]. Land suitability studies concentrating on finding proper lands for renewable energy production will reduce the gap between planning policies and renewable energy planning [40,41]. Geographic Information System (GIS) is one of the methods for identifying site suitability; thus, it is an essential tool for spatial planning (it is a comprehensive approach and geographical expression to the economic, social, cultural, and ecological policies of society. It aims to balance regional development and the physical organization of space according to an overall strategy) and management of renewable energy landscapes, such as wind farms. GIS-based approaches can help in minimizing errors by identifying the suitability of AOI through manipulating a combination of digital thematic maps and attribute data variables [42,43]. For example, Noorollahi, et al., (2016) [22] employed a Weighted Index Overlay (WIO) method using a GIS modeling approach with a Multi-Criteria Decision Making (MCDM) support system to determine potential locations for wind farms in Markazi Province, Iran.
Many variables are defined and judged by setting different criteria that are considered throughout restriction and suitability phases [22,44]. Noorollahi et al. (2016) [22] considered a group of criteria through two phases. The first employed restrictive criteria (residential areas, airports, ancient and cultural monuments, rivers, coastlines and wetlands, environmental protected areas, lakes and water bodies, faults, digital elevation model, and slope) [22]. The second employed suitability criteria (wind speed, electrical power lines, highway, roads, and railway) [22]. Similarly, Haaren and Fthenakis (2011) [45] define three stages to select the most feasible wind turbine sites in New York State, USA [45]. They identified geological constraints, cost value, and ecological impacts [45]. Other studies adopt climatic, socioeconomic, environmental, and geological variables to locate suitable sites for wind farms [45][46][47]. Some consider the economic feasibility aspect one of the most important optimization factors used to identify the locations of wind farms [38,45]. It is logical to say that wind turbines are best located in areas where wind energy can be harvested efficiently. However, if these optimal locations are remote, planning for development and investment projects should take place before the wind farms are installed, or it would be difficult to transport energy from such locations [28].
There are disparities among studies, each selecting different variables/criteria to find suitable locations for wind farms. This is usually based on their objectives, existing constraints, data availability, and identified most suitable turbine hub heights: 50 m [46,48,49], 80 m [22,38,49], and 100 m [49,50].
This study, however, adopts a comprehensive set of variables, including land-use/ landcover, road network, electrical power lines grid, digital elevation model (slope and aspect), wind speed, and wind power density data at different heights. These variables are obtained spatially from GIS national records and are divided into two parts: restrictive and classifying layers. The primary difference between this study and existing studies is that this research utilizes nationwide wind power and wind energy maps that cover the whole geographic area instead of taking specific meteorological readings, which are limited to a few locations across the AOI [51]. The wind data is obtained from Global Wind Atlas to provide a more comprehensive data approach for developing countries that lack actual wind-related measurements and readings [52]. This research offers a spatial resolution of 250 m (which is high on a regional scale), thus increasing the accuracy when analyzing the AOI. Sites are selected based on feasibility through a cost-revenue optimization and energy production scenario using the available wind speed and wind power density at different heights (50 m, 100 m, 200 m) from Global Wind Atlas. Finally, due to the common seismic activities in the region, this research is adding earthquake potential hazard map criterion to the variables influencing the selection of wind farm suitable sites. The process will develop a framework that can be implemented in other places in the world.

Area of Interest (AOI)
Jordan is located between Asia and Africa and is considered a central transit area that plays a key role in linking electricity, gas, and oil networks between continents. Its 2020 estimated population of 10.1 million consists of 69.6% of residents and a staggering 30.4% of regional post-war refugees and immigrants [53]. Jordan has three main territorial regions with four governorates each: the Northern (Irbid, Ajloun, Jerash, and Mafraq) with an overall population of 2.73 million; the Central (Balqa, Amman, Madaba, and Zarqa) with an overall population of 6.053 million; and, the Southern region (Karak, Tafielah, Ma'an, and Aqaba) with an overall population of 0.75 million [53] (Figure 1). Jordan's difference in elevation ranges from 430 m below sea level to 1754 m above sea level. This elevation difference (2184 m) is a positive factor for wind energy generation in most regions because it works to change the air pressure from one region to another. Thus, the flow of winds at various speeds and densities [54].
The process will develop a framework that can be implemented in other places in the world.

Area of Interest (AOI)
Jordan is located between Asia and Africa and is considered a central transit area that plays a key role in linking electricity, gas, and oil networks between continents. Its 2020 estimated population of 10.1 million consists of 69.6% of residents and a staggering 30.4% of regional post-war refugees and immigrants [53]. Jordan has three main territorial regions with four governorates each: the Northern (Irbid, Ajloun, Jerash, and Mafraq) with an overall population of 2.73 million; the Central (Balqa, Amman, Madaba, and Zarqa) with an overall population of 6.053 million; and, the Southern region (Karak, Tafielah, Ma'an, and Aqaba) with an overall population of 0.75 million [53] (Figure 1). Jordan's difference in elevation ranges from 430 m below sea level to 1754 m above sea level. This elevation difference (2184 m) is a positive factor for wind energy generation in most regions because it works to change the air pressure from one region to another. Thus, the flow of winds at various speeds and densities [54].
In recent years, Jordan has developed many policies and regulations to encourage renewable energy projects (wind, solar, and biomass) as a source of electricity generation. As an incentive, all renewable energy projects are of renewable energy are exempt from duties and taxes. Jordan has made several preparations to invest approximately $14-18 billion in renewable energy projects to address unavoidable rises in international oil prices, to reduce traditional fossil fuel energy consumption, and to face growth of energy demand and degradation in the natural environment [55].

Energy Situation in Jordan
According to The Statistical Review of World Energy (2020), fossil fuels are still the main energy source which supplies 84% of world energy [56]. In 2019 the growth consumption slowed by (+0.6%) compared to an average of 2%/year over the period between In recent years, Jordan has developed many policies and regulations to encourage renewable energy projects (wind, solar, and biomass) as a source of electricity generation. As an incentive, all renewable energy projects are of renewable energy are exempt from duties and taxes. Jordan has made several preparations to invest approximately $14-18 billion in renewable energy projects to address unavoidable rises in international oil prices, to reduce traditional fossil fuel energy consumption, and to face growth of energy demand and degradation in the natural environment [55].

Energy Situation in Jordan
According to The Statistical Review of World Energy (2020), fossil fuels are still the main energy source which supplies 84% of world energy [56]. In 2019 the growth consumption slowed by (+0.6%) compared to an average of 2%/year over the period between 2000 and 2018 due to the slower economic growth [56,57]. Jordan is no exception, where it has one of the most imported fossil fuel-dependent countries in the world in 2017 [58]. Eighty-nine to ninety-three percent of the country's energy needs are met by oil and natural gas imports [59,60]. The remainder (7-11%) is supplied by renewable energy [59]. In 2018, foreign oil imports accounted for $3426 million USD (8.5% of total GDP of $40 billion USD) [61]. Furthermore, from 2001 and 2019, Jordan's public debt has increased at an average annual rate of 9% [62]. The last three years had a rate of 11.8%. Besides the debt, the GDP growth rates continued to decline from 3.8% in 2011 to 1.8% in 2019 [63]. National Energy Strategy for 2007-2020 was created to select new projects to boost reliance on local energy sources from 4% to 40% by the end of the decade [55]. By establishing wind turbine farms, Jordan will thus be able to secure long-term energy by reducing its dependence on energy imports, meeting the growing demand for energy, securing long-term energy supplies, and avoiding the exploitation of the geography and climate of the region.

Methodology and Criteria Evaluation
This study investigates regional energy planning strategies using GIS to identify the most suitable areas for establishing wind turbine farms in Jordan. This methodology was divided into two stages. The first stage applied a restrictive method. At this stage, all unsuitable areas were excluded from the study. In the second stage, a classifying analytical method was applied to define the most suitable areas for harvesting wind energy at three different hub height scenarios: 50 m, 100 m, and 200 m. The analysis compared scenarios with each other to determine feasibility. It employed a systematic approach for regional spatial planning.
Many criteria help in determining the most appropriate location for wind farms. This study maps the most suitable areas for establishing wind farms by identifying the different suitability criteria used, calculating and applying the influence/weight of each criterion in the study based on Analytical Hierarchy Process (AHP) [64], and developing a GIS-based model to determine site suitability for the study area. Appendix A has the top-weighted criteria that had a very strong impact on the study. The study divided the previously identified criteria from the literature into four categories: economic, technical, environmental, and social [22,46,47,49,50,57,65]. The weights of each criterion were determined based on AHP method and compared with average weights from several literature sources [22,35,47,66] to give the final relative weighted scores.
The economic aspect affects the choices for suitable wind farm sites depending on site complexity and infrastructure costs in addition to the extreme energy production requirements. Therefore, site-specific criteria such as slope, aspect, distance to roads/railway, distance to airports, and proximity to the power grid are important variables [38,45]. These variables help in minimizing capital and operating costs when finding suitable sites for wind farms, thus making the project more feasible and accessible for investors.
Technical criteria consist of analyzing wind conditions which are the most important determinants for selecting wind farm locations to maximize energy production and minimize risk. They include the average wind speed, wind power density, proximity to the power grid, minimum turbine spacing, turbine size, and proximity to potential earthquake hazards [22,39,46,48,49,65]. Other technical factors will not be considered in this study, such as the wind park effect (this is the effect of aligning the wind turbines where each wind turbine will potentially reduce the speed of the wind behind it because of the wake effect [67,68]. Thus, aligning them at close distances will slow down the wind received by the next turbine in line along the prevailing wind direction.), air density, site-specific conditions, foundation material, and turbine design [69][70][71]. These factors are more site-specific at a micro-scale which is not the focus of this study. Environmental criteria determine certain restrictions such as proximity to environmental reserves, water bodies, forests, and quarry lands which affect water quality, biodiversity, and landscape/seascape [45,47]. Environmental reserves, archaeological sites, urban areas, forests, water bodies, quarries, and airports are excluded from the suitability including a buffer surrounding each location. Current micro-scale onsite vegetation, wildlife biodiversity, and other aesthetic values are not considered in this study due to the macro scale of this study.
Lastly, social criteria are one of the most critical considerations to address when locating wind farms because they affect national economic growth, ensure comprehensive advancement, and protect economic prosperity to boost urban living standards. To ensure the stable and efficient operation of wind power generation, the social capital that may be impacted by the proposed development should be identified and studied. Consequently, residential areas are defined and buffered (with a buffer parameter of 2000 m) to avoid and/or mitigate the impact of wind farms on the local population. Shadow flicker, noise, and visual impact are examples of specific issues that matter to the urban areas. To support public health and other social issues for each chosen wind farm, each may need a standalone dedicated micro study [72,73].

Preparation of Land Suitability Data
After determining the influential criteria, several map layers concerning the study area have been collected and digitized to address each criterion. Appendix B identifies data sources for each layer using ESRI ArcGIS software. All layered data was projected to a Universal Transverse Mercator (UTM) coordinate system WGS_1984_UTM_Zone_36N.

Determination of Suitability Score and Weight Values
To determine the Suitability scores and weight values for the geographic location criterion, the researchers established standardized categories of suitability using a five-level ordinal scale including very high, high, moderate, low, and not suitable for each factor.
To achieve this, the study utilized a protocol of three stages incorporating multiple digital data layers for a wind farm suitability analysis. Stage one (i.e., restrictive method) excluding both restricted areas and their buffers in land-use/landcover criteria (environmental reserves, archaeological sites, urban areas, forests, water bodies, quarries, and commercial and military airports) ( Table 1). In stage two (i.e., classifying analytical method) the suitability score values (rating values) for each geographic location within the single criterion (i.e., proximity to main roads and railway, proximity to main electrical power lines, slope, aspect, wind speed, wind power density, and proximity to faults as potential earthquake hazard locations) were determined based on an ordinal scale between 1 and 5 ( Table 2). The classification considered 5 as most suitable and 1 as least suitable, and the 0 score value was considered as not suitable.

Determination of Suitability Score and Weight Values
In the third stage, the weight value for each criterion was calculated using AHP analysis and its pairwise matrix. AHP analysis is one of the most powerful and common multi-criteria decision-making tools in various fields of economics, politics, planning, and engineering [76]. It makes a hierarchical structure to classify and select alternatives by pairwise comparison of criteria to calculate the weight influence [77]. The pairwise matrix represents a theoretically founded approach to computing weights representing the relative importance of criteria.
Once the spatial distribution maps of the score values are generated for each criterion, the suitability map for wind farms was generated through an index overlay procedure using Equation (1). Each output raster cell is the sum of the weighted products for each corresponding cell factor which is produced using GIS overlay tool function.

Results
The results section will report the findings of suitability based on turbine hub height, then based on the geographic region. In each case, high suitability to low suitability is reported while indicating the sum of areas for each category. This section will proceed by providing a feasibility study based on the results. Further feasibility will be applied to the northern region to calculate the actual benefits of this study.

Land Suitability Results Based on Turbine Hub Height
National suitability maps are produced at three potential turbine hub heights: 50 m, 100 m, and 200 m (Figures 4 and 5). The turbine hub heights are chosen due to the availability of maps for wind speeds and wind power density at these heights as obtained from Global Wind Atlas. Although commercial turbines are typically installed at a height of 80 m in most parts of the United States and the United Kingdom, a recent study by the National Renewable Energy Laboratory (2019) found that in 70% to 90% of locations (depending on the specific turbine configuration) in the United States, the more costeffective option is to strive for 160 m hub heights [78].

Findings Identified by Region
The following three sections will demonstrate the findings of each region concerning wind farm suitability areas associated with the different wind turbine heights. It includes the Northern, Middle, and Southern Regions. It is found more common to use 75-134 m in the Middle East region [79]. For example, as established in Shobak at the south of Jordan, the turbine hub height was erected at 137 m on a land elevation of 1643 m above sea level [80,81]. In another project in Shobak, the turbine Tip Height of 180 m which include the turbine hub height was 112 m and a blade length of 68 m [82]. Depending on a variety of factors, including hub height, most suitable areas have a greater potential to generate electricity, while less suitable areas have a lower potential to generate electricity ( Figure 5).
At a 50 m height, the total area identified with high suitability is 6624.5 km 2 constituting 0.07 of the 89,342 km 2 of the national area in Jordan; moderate suitability is 69,106.8 km 2 constituting 0.77 of the national area; and low suitability is 1390.3 km 2 constituting 0.02 of the national area (Appendices C and D).
Likewise, at 100 m height, high suitability is 19,379.7 km 2 constituting 0.22 of the national area; moderate suitability is 56,727.1 km 2 constituting 0.64; low suitability is 1014.8 km 2 constituting 0.01 of the entire area of Jordan (Appendices C and D).
At 200 m height: high suitability is 33,821.7 km 2 , which constitutes 0.39 of the national area; moderate suitability is 42,743.1 km 2 , constituting 0.48 of the national area; and low suitability is 556.9 km 2 , constituting 0.01 of Jordan's national area (Appendices C and D).
The highest percentage of the low and moderate suitability was at a height of 50 m, with a regarded area of 1390.3 km 2 , and 69,106.8 km 2 , respectively. For the high suitability class, the highest percentage was at a height of 200 m, with a regarded area of 33,821.7 km 2 ( Figure 4).

Findings Identified by Region
The following three sections will demonstrate the findings of each region concerning wind farm suitability areas associated with the different wind turbine heights. It includes the Northern, Middle, and Southern Regions.  When reviewing all areas with the highest suitability, Mafraq governorate is most suitable at the three heights and has an outstanding total area of 22,366 km 2 out of the total Northern region identified as having high suitability.
The results are summarized in the two figures displayed in Appendix E. The graph shows a comparison of findings and the figure shows the suitable areas in the Northern Region. Mafraq has a great potential for establishing wind farms.

Central Region
Areas identified with high suitability in the Central Region at a height of 50 m span a total area of 749.9 km 2 . Governorate shares include Amman (559.6 km 2 ), Zarqa (142.8 km 2 ), Madaba (42.8 km 2 ), and Balqa (7.8 km 2 ).
At the height of 100 m, areas with high suitability total 2513.9 km 2 . Governorate shares include Amman (1829.7 km 2 ), Zarqa (623.6 km 2 ), Madaba (55.7 km 2 ), and Balqa Reviewing the areas with high suitability, Amman governorate is the most suitable at the three heights and has a promising total area of 5200.8 km 2 . Reviewing the areas with high suitability, Ma'an governorate is the most suitable at the three heights and has an outstanding total area of 22,757.5 km 2 of suitable lands.

Feasibility Study Based on the Results
Wind power production projects come at a high cost initially but are profitable in the long run. Many factors affect the initial cost of investment: the cost of wind turbines, the number of turbines, construction cost, cost of project land acquisition, cost of transmission lines, taxes, and incentives [2,83]. According to the American Wind Energy Association (AWEA), commercial wind turbine costs range from $1.3-$2.2 million USD, for a 1 MW turbine in 2019. Today, most projects install a 2 MW wind turbine which costs around $3-$4 million USD per wind turbine [84], or high-capacity wind turbines with 3.45 MW which has an associated cost of $4 million USD [85]. According to National Renewable Energy Laboratories (NREL), Equation (2) P cost to gen : cost to generate power. FCR: fixed charge rate.
Equations (3)-(5) show that the cost to generate power is reasonable when using turbines at a height of 200 m. This is caused by the manufactured turbine itself. Since the selected turbine at a height of 200 m has the largest size (3.45 MW) and the expected life of a wind turbine is 25 years, it has to work approximately 4.7 years before costs are paid off. In return, it will continue to operate for 20.3 years at full profit. For detailed calculations see Appendix F.

Implementing the Study on the Northern Region/Mafraq Governorate
To examine the coverage and feasibility, this study tested the results in the Northern Region/Mafraq Governorate as an illustrative example (Table 3). This region provided a sufficient example where suitable areas were agglomerated at two major locations: one close to the urban areas and another far from urban areas. Data on electrical consumption in the Mafraq Governorate was available to support the results.
At a height of 50 m, suitable high lands at Mafraq Governorate could produce enough electrical energy to meet 274.3% of the total Jordanian energy demands (Appendix G). This means that Mafraq could generate sufficient electricity to fulfill all of Jordan's electricity needs and have an excess of 174.3% that can be exported or used in other new functions such as heating in winter, which depended on fossil fuels mainly. The number of turbines required to cover 100% of Jordan's electrical consumption is 5709. The annual profit of 5709 turbines would be $1.35 billion USD with an estimated cost of $7.42 billion USD.
At a height of 100 m, the number of turbines required to cover 100% of Jordan's electrical consumption is 2854. The annual profit of 2854 turbines would be $1.31 billion USD with an estimated cost of $8.56 billion USD.
At a height of 200 m, the number of turbines required to cover 100% of Jordan's electrical consumption is 1654. The annual profit of 1654 turbines would be $1.42 billion USD with an estimated cost of $6.62 billion USD.
These calculations show that it is more feasible to install turbines at 50 m height than it is at 100 m height in the Mafraq Governorate ( Figure 6) (Table 3). However, installing turbines at 200 m height is less expensive and rather more rewarding ( Figure 5). Figure 6 shows the relationship between the turbine height in meters, the annual profit, and the cost in American Dollars. The dotted trend line has the estimated cost, and the dashed trend line is the estimated annual profit. If this annual profit is steady, it is expected to take an average of 5.5, 6.5, and 4.7 years to regain the cost of the 50, 100, 200 m high turbine hub, respectively.  turbines at 200 m height is less expensive and rather more rewarding ( Figure 5). Figure 6 shows the relationship between the turbine height in meters, the annual profit, and the cost in American Dollars. The dotted trend line has the estimated cost, and the dashed trend line is the estimated annual profit. If this annual profit is steady, it is expected to take an average of 5.5, 6.5, and 4.7 years to regain the cost of the 50, 100, 200 m high turbine hub, respectively. According to the World Bank, Jordan's GDP is around $40 billion USD [61]. The calculations show that the highly suitable areas at a height of 50 m produce electrical energy that could boost the national GDP by 3.4% with an annual profit of $1.35 billion USD. Appendix G shows the consumption of electrical energy for the Mafraq governorate during 2017. July was the highest month of consumption with 99,353,787 kWh, while February was the lowest month of consumption with 63,803,956 kWh because they rely on fossil fuels for heating in the winter [58]. Once renewable energy is available at comparable prices, the total consumption may increase, necessitating the production of more wind energy in all Governorates based on the suitability map and the area characteristics. It is still unknown how the consumption pattern will evolve. The relationship between turbine hub height, annual profit, and turbine cost for the Mafraq Governorate The Annual Profit Total Cost Estimation According to the World Bank, Jordan's GDP is around $40 billion USD [61]. The calculations show that the highly suitable areas at a height of 50 m produce electrical energy that could boost the national GDP by 3.4% with an annual profit of $1.35 billion USD. Appendix G shows the consumption of electrical energy for the Mafraq governorate during 2017. July was the highest month of consumption with 99,353,787 kWh, while February was the lowest month of consumption with 63,803,956 kWh because they rely on fossil fuels for heating in the winter [58]. Once renewable energy is available at comparable prices, the total consumption may increase, necessitating the production of more wind energy in all Governorates based on the suitability map and the area characteristics. It is still unknown how the consumption pattern will evolve.
Currently, the Mafraq governorate's energy needs account for 132,214,418 kWh/year [58]. To calculate the number of wind turbines needed to cover the electrical consumption of Mafraq governorate at a height of 50 m, Mafraq consumption was divided by the annual energy production for an individual wind turbine at a height of 50 m which results in a total of 43.1 wind turbines. This means that about 44 wind turbines are needed to cover the electrical consumption of the Mafraq governorate. At the height of 100 m, the number of wind turbines needed to cover the current demand is 21.6 turbines while 12.5 turbines are needed at a height of 200 m (Appendix G).

The Developed Framework
The implementation of a feasible regional wind farm planning framework will require several basic phrases. The first is studying the national electrical energy consumption. It is best if the information on power consumption and production is province-or governorate-based. In this case study, industrial use of electricity is negligible compared to domestic/commercial uses. However, when implemented in other case studies, domestic/commercial and industrial consumption may be separated to help in assessing the actual production and consumption times and amounts. It will also be useful to take into consideration any future policy-related aspects regarding power generation. A second important phase is to identify potential wind farm locations. This step is dependent on estimated or actual meteorological information in addition to other geo-information. The details of this phase are laid out in this study where spatial data exclusion precedes suitability analyses to account for some restrictions regarding wind speed, preserves, urban areas, etc., as explained in the suitability analysis. The third phase depends on wind turbine engine types, heights, availability, prices, etc. This is directly related to turbine technology and characteristics that are essential to calculate the feasibility of the proposed wind farm locations. Before the implementation of any selected site, the authorities or the investors are responsible not only for the feasibility of the project but also for its acceptance by the locals and the policy-makers. Therefore, additional phases are required to study the locations that best benefit urban areas as well as potential industrial or agricultural projects that are energy-dependent. A temporal plan must be laid out to study the time of consumption suited for the urban areas and the times when energy can be consumed by other rural and remote activities.

Discussion
The aims of this research are to re-highlight renewable energy sources with a focus on wind energy as an alternative energy source to fossil fuels, enhance the economic potential of Jordan by defining the most suitable areas for establishing wind turbine farms, and select the most feasible sites based on spatial cost-revenue optimization in Jordan. It is employing GIS to achieve long-term objectives such as improving environmental protection by lowering greenhouse gas emissions and addressing the depletion and consumption of electric power and its impact on the national GDP. This research assesses the economic, governmental, and environmental dimensions, to lead the way for integrated regional energy planning by combining the spatial mapping and land suitability demand for energy resources.
What sets this study apart from others is the following: First, it is discussing Jordan's electric power production and import prices, as well as their effects on the country's GDP. Second: it uses a resolution of 250 m at a regional planning scale which increases the accuracy of the site selection. Third: it selects the most feasible sites based on spatial cost-revenue optimization. Fourth: it introduces different scenarios at different prospect wind hub heights. Fifth: it applies a new earthquake potential hazard map criterion as part of selecting potential wind turbine sites. This research will be the first of its kind to study and analyze wind energy in Jordan at the regional scale and will therefore be the basic reference for many future subsequent studies.
Wind energy is considered more feasible than solar energy for many reasons; it uses less energy, produces less carbon dioxide, and can generate power 24 h/day since it is not dependent on sunlight, thus produces more total energy. One wind turbine can generate the same amount of energy in kWh as that produced by thousands of solar panels saving on area consumption, maintenance, and cleaning costs [88]. We have to acknowledge that this is an optimistic view of wind energy. The wind doesn't always blow at the average or optimal speed in even the most suitable selected sites. Therefore, a hybrid energy system consisting of at least two of the many renewable sources (wind, solar light, water, geothermal heat, etc.) is a smart solution [89]. In a study on future energy scenarios in Jordan, one scenario that proposes a 100% renewable energy dependence suggests 55-67% reliance on wind energy as opposed to 13-15% reliance on PV-UTL among the many sources of local energy [90]. This hybrid energy system is used in many places around the world. It depends on producing energy for consumption from other sources such as fossil fuels and solar panels [89,91].
This research used GIS to find the best locations for wind farms based on comprehensive criteria, which can enable decision-makers to make appropriately informed decisions regarding their selection. Additional help is gained from integrating the GIS model with AHP to solve geospatial problems by determining how each criterion affects the study. The Expert Choice tool was employed for a more objective weighting process.
The study revealed many potential benefits for the economy in the AOI. According to the World Bank, Jordan's current GDP is around $40 billion USD [61]. Examining the production potential of highly suitable areas at a height of 50 m, electrical energy production could increase the national GDP by 3.4% with an annual profit of $1.348 billion USD. This is not new in this field-many national studies aiming at boosting the local economy using wind energy are already applying it with great benefits to the local energy production and revenues. Leading countries include China, USA, Germany, India, Spain, UK, France, Canada, Sweden, Netherlands, and Denmark [25][26][27]. Climate Council news announced that many countries are already achieving in their dependence on renewable energy [92]. For example, Costa Rica is already 95% dependent on renewable sources of energy; Nicaragua is 90% dependent on renewable sources; Scotland is 98% dependent on wind energy now; and Uruguay is 100% dependent on a hybrid system of wind and solar energy [92].
Individual governorates and their municipalities should take into consideration a framework for implementing wind energy projects surrounding urban areas. The steps towards implementation are as follows; review the map of high suitable areas for wind farms from this study; determine the height of the optimal turbine hub, calculate wind speed at the selected height; study the feasibility of selected areas at the selected height; and select the type of wind turbine.
Electricity production revenue can be reinvested with ways to improve the country and its infrastructure. Many identified highly suitable lands are in remote areas where energy can be used to serve for:

•
Providing a new land-use planning system that supports and protects the lands designated for generating wind energy to enable all areas to operate with high productivity while providing the necessary energy for that. This is established by creating a landuse layer indicating the suitability of land for wind farm installations. In this respect, the United States is one of the leading nations [78]. India, too, is working to close energy gaps for its rapidly expanding population by developing maps for solar and wind suitability classes [93]. A consolidated effort is being made to unify constraints for appropriate land selection for onshore wind installations on a European scale [94]. • Creating controlled-climate agricultural areas in which agriculture can depend on modern concepts for lush growth. As long as the necessary energy for irrigation, lighting, and climate control is available, we can speed up production processes and develop more productive crop-based needs to create food security for an expanding population. In addition to the direct employment opportunities in wind farm installations, there are indirect employment opportunities in the investment projects. For example, wind power farms indirectly boosted the Brazilian agricultural employment levels by 64% and the wages by 131% [95]. They found that it also boosted the industrial and construction sectors, especially among the less-educated population, enhancing the social and economic status of their families and increasing social welfare in this developing nation. An earlier study on "valuing the attributes of renewable energy investments" also found that the benefits of renewable energy projects are mainly on the socioeconomics of the rural population [96]. • Producing the energy needed to establish new industrial cities in remote areas and providing the necessary infrastructure. This will create new job opportunities, increase gross domestic product, and enhance industrial production, which will positively affect exports. Such projects will create employment opportunities and encourage migration to rural areas. A recent study in Wales, UK, that investigated the complex investment in energy and other industries showed that success is also related to the amount of local capital. Therefore, when the regional investment falls short, investment is more likely to be handled at the national level than locally to maintain its sustainability [97]. • Instead of living in the areas most suitable for farming, the wind farm project will encourage the urbanization of more arid regions to spare the fertile lands for food production. When energy is readily available, many challenging living conditions may be overcome such as the souring hot days when energy is so cheap to cool the living quarters. Also, with readily available energy, the creation of smart cities becomes attractive. A living example is Masdar City in Abu Dhabi, the United Arab Emirates, which stands as a model for a smart, sustainable city benefiting from solar energy [98]. If established in remote arid areas, this will also secure jobs for the new agglomerations and prevent migration to big cities.
In this study, the generated maps are not just for the greater national and governorate goals but also to support the development of remote lands for farming purposes by providing energy for irrigation which would also support the growing food-based needs of an expanding population. It can also support the generation of many types of industrial sites in remote arid lands.

Conclusions
By investing in wind energy, Jordan can reduce its dependency on fossil fuels. Wind energy farm investments will introduce dynamic and socioeconomic development, employment opportunities, and environmental protection.
The proposed framework estimates the geographical distribution of wind energy resources by including environmental, technical, social, and economic criteria to achieve a framework for spatial regional energy planning. This study added a new criterion responsible for geological faults to account for seismic activity. GIS software identified the most suitable areas for establishing wind farms in Jordan. This methodology was divided into two stages. The first stage applied a restrictive method. At this stage, all unsuitable areas were excluded. The second stage followed an analytical method to define the most suitable areas for harvesting wind energy at three different elevation scenarios (50 m, 100 m, and 200 m). The criteria were given weights based on an AHP method through the system software called Expert Choice.
The outcomes of the case study show that 7.4% (6624.5 km 2 ) of the study area has high suitable areas for the installation of wind farms at a height of 50 m; 21.7% (19,379 This leads to the conclusion that the area of suitable high lands increases with the height of the prospect wind hub. However, the moderately suitable land area increases as the height decrease. Second, suitable land is sufficient at moderate and high levels on all three hub elevations. However, there isn't much of a distinction in wind turbine installation costs between the three kinds of wind turbine heights. Although from many perspectives it is practically more difficult to establish the 200 m hub turbines, it is not so much more than the cost of the 100 m hub turbines. A wide study on the United States showed that technologies with larger potential can now be found, such as tubular steel using soft-soft design criteria [78]. They are prominent in the United States. But to weigh things out, it is wiser to choose manageable heights of 100-150 m.
What happens when the wind isn't strong enough to keep the turbine running? It's worth considering incorporating solar energy into the same wind turbine tower to help the blades maintain momentum on sunny and less windy days. Engineers in charge of more innovative design should look into using the towers to gather solar energy while still producing energy with the wind. Some studies already started exploring this alternative [67]. There is a vast array of innovation that has yet to be explored that has the potential to increase the economics of wind power [78,99]. Research on developing technology, materials, and aerodynamics is gradually bringing affordable, viable, and appealing solutions.
The produced maps serve as an atlas for wind farm planning in the AOI. They will surely aid the process of sustainable regional planning by exhibiting suitable locations and levels of suitability. The suitability is also based on the feasibility and the potential of adapting places to the restrictive criteria while abiding with the local policies. Once the locations are appropriate and feasible, they present a valuable future regional optimization plan to boost the national economy and make living sustainable and affordable for people. The results could be supported by developing a road map for renewable energy systems based on locally available resources. Future land-use plans and comprehensive plans should include a wind farm suitability layer to facilitate future investment in wind farms for urban, agricultural, and industrial purposes. This will help future high-efficiency decision-making policies foster long-term economic growth in the places suited for energy production and consumption while sparing fertile lands for rain-fed food production. This finding is backed by prior regional studies on land suitability and landscape character preservation [74,100].

Recommendations
It is recommended to undertake further studies for each governorate to calculate energy demands, the amount of energy that could potentially be generated, the real impact of this influx of energy on individual cities, and how the produced energy may be used or consumed. It is also recommended to re-examine the tariff price per watt and the proper scenarios for returns of investment value on exporting energy costs. Additionally, it is advised to study the effects of changing peak hour demands through a decrease of the tariff rate during the hours when the load is low to encourage people to use electrical energy at low hour demand times and reduce energy needs during peak times. The most intelligent approach is to use hybrid power systems that support energy with both wind and solar energy [91]. Although solar panel maintenance is expensive, in semi-arid regions such as the Middle East, the use of solar panels is a smart alternative to complete power generation and maintain it at all times [101]. Weighing the cost/benefit is important, but it is wise to weigh the percentage of each power so that optimization can be achieved by utilizing both solar and wind power in any location [89].
Other scenarios for using wind farms are possible such as the potential hydrogen production from wind farms [102]. In this case, a whole line of direct production is introduced that may as well elevate the GDP levels for any country. Besides, and under other similar research, it is possible to carry this a step further by finding the levels of acceptance of these farms by the locals and policy-makers. Since there is a lot of impact on the landscape character and place memory in the minds of locals, they often have varied opinions towards landscape change [100,103]. Therefore, consultation with the locals is also important to consider. Many recent studies focus on technological legitimation (community acceptance), indicating the importance of public participation in decision-making [104].
This research is subject to several limitations, including the inability to access up to date digital maps (land-use/landcover, wind speed, wind power density, electrical power lines, roads); more detailed feasibility studies; and the inaccessible information regarding actual local monitoring for wind speed and wind power density at different heights in the most suitable locations.

Data Availability Statement:
The data presented in this study are available on request from the corresponding author.
Acknowledgments: This work is part of a larger project on sustainable regional planning supported by fund number 689-2018. We thank the Deanship of Research at Jordan University of Science and Technology for granting us this fund. Special thanks to Global Wind Atlas, Danmarks Tekniske Universite, where we obtained wind speed and wind power density estimates [52].

Conflicts of Interest:
The authors declare no conflict of interest.

Appendix B
Resources for each layer were using ESRI ArcGIS 10.5 software. All layered data was projected to a Universal Transverse Mercator (UTM) coordinate system WGS_1984_UTM_ Zone_36N. Data layers had a standard 250 m spatial resolution. In particular, Wind data was obtained from the Global Wind Atlas 3.0; a free web-based application developed, owned, and operated by the Technical University of Denmark (DTU) in partnership with the World Bank Group, utilizing data provided by Vortex, with funding provided by the Energy Sector Management Assistance Program (ESMAP). https://globalwindatlas.info accessed on 12 Feburary 2019.    FCR: fixed-rate, is "the fraction of the Total Installed Cost that must be set aside each year to retire capital costs which include interest on debt, return on equity, and so forth" In Jordan, all power generation projects of renewable energy are exempted from duties and taxes. In this case, we will assume a 1% for each project. FCR = 0.01 IC: the initial cost for each turbine (million USD). FCR: fixed-rate, is "the fraction of the Total Installed Cost that must be set aside each year to retire capital costs which include interest on debt, return on equity, and so forth" In Jordan, all power generation projects of renewable energy are exempted from duties and taxes. In this case, we will assume a 1% for each project.   P cost to gen = 0.029 P cost to gen = 2.9 c/kWh (cent per kilowatt hour). To find the total Annual Expenses: Tae = P cost to gen × AEP Tae: total annual expenses P cost to gen : cost to generate power. AEP: net annual energy production, kWh. I g = 0.11 c/kWh × 10,577,700 kWh/year I g = $1,163,547 USD To find the annual profit (P a ) of the turbine: P a = (P selling price -P cost to gen) × AEP Pa: annual profit P selling price : selling price power P cost to gen : cost to generate power AEP: net annual energy production, kWh. For a height of 50 m: P a = ($0.11 -$0.033) × 3,066,000 kWh/year P a = $236,082 USD For a height of 100 m: P a = ($0.11 -$0.035) × 6,132,000 kWh/year P a = $459,900 USD For a height of 200 m: P a = ($0.11 -$0.029) × 10,577,700 kWh/year P a = $856,793.7 USD To calculate how long it will take for this investment to be paid off: BEP = C turbine /P a BEP: Break-Even Point C turbine : turbine cost P a : annual profit Since the expected life of a wind turbine is 25 years, it has to work approximately 5.5 years before costs are paid off. It will continue to operate for 19.5 years at full profit. Jordan has sold electricity at 11 c/kWh, Power generation by wind turbines costs 3.3 c/kWh, this means that 7.7 c/kWh will be the direct profit for the country.
For a height of 100 m: BEP = $3,000,000 USD/$459,900 USD BEP = 6.5 years Since the expected life of a wind turbine is 25 years, the turbine has to operate for 6.5 years before its costs are paid off. It will continue to operate for 18.5 years at full profit. Jordan has sold electricity at 11 c/kWh, Power generation by wind turbines costs 3.5 c/kWh, this means that 7.5 c/kWh will be the direct profit for the country. Since the expected life of a wind turbine is 25 years, it has to work approximately 4.7 years before costs are paid off. It will continue to operate for 20.3 years at full profit. Jordan has sold electricity at 11 c/kWh, Power generation by wind turbines costs 2.9 c/kWh, this means that 8.1 c/kWh will be the direct profit for the country The area for each turbine depends on the state of the site. Distance between turbines expressed in the rotor diameter of the turbine (D). Range of this space 6 -10 D. Many considerations should take into account when deciding the range, such as turbine hub (m), wind direction, terrain, and other setback regulations.
This spacing performs a compromise between compactness, thus minimizes the initial cost, and prevents any disturbance in airflow which would create turbulence, and makes the turbine less efficient. In this study, assumption of area = 6D × 10D is assumed per  Area of Mafraq at a height of 50 m, high suitability class = 2349 km 2 To calculate the area required for each turbine: The required area of each turbine depends on the nature of the terrain, aligned orientation, the number of turbine lines, the capacity size of each turbine, the wind rose for a site, and many more. The installation area should have 10 rotor diameters of clearance in the direction of the wind and 3 rotor diameters in every other direction (total 6D). We assumed here to take the average space required to install each turbine is 6Dx10D (National Wind Watch, 2021).