Anaerobic Treatment of Concentrated Black Water in a Uasb Reactor at a Short Hrt

This research describes the feasibility of applying a UASB reactor for the treatment of concentrated black (toilet) water at 25 °C. On average 78% of the influent load of COD at an HRT of 8.7 days was removed. Produced methane can be converted to 56 MJ/p/y as electricity and 84 MJ/p/y as heat by combined heat and power (CHP). Minimum reactor volume at full scale was calculated to be 63L per person (for black water containing 16 gCOD/L produced at 5 L/p/d) and this is more than two times smaller than other type of reactors for anaerobic treatment of concentrated black water.


Introduction
Separation of domestic waste(water) at the source results in black water from the toilet (faeces and urine) and less polluted grey water from showers, laundry and kitchen.These source separated waste(water) streams differ in quantity and quality and should be treated separately according to their concentrations and composition.The main benefits of such an approach include the possibility of recovering energy and nutrients and the efficient removal of micro-pollutants.Grey water has a high OPEN ACCESS potential of reuse because it is the major fraction (70%) of domestic wastewater and relatively low in pollution [1].Black water contains half the load of organic material in domestic wastewater, the major fraction of the nutrients nitrogen and phosphorus [2,3] and can be collected with a small amount of water (one liter per flush) using, for example, vacuum toilets.Black water also contains most of the pathogens, hormones and pharmaceutical residues.The volume of black water depends on the type of toilet and amount of water needed to flush.
Anaerobic treatment is regarded as the core technology for energy and nutrient recovery from source separated black water [3][4][5] because it converts organic matter to methane, which can be used to produce electricity and heat, while at the same time anaerobic treatment yields low amounts of excess sludge.The nutrients are largely conserved in the liquid phase and can be subsequently recovered with physical-chemical processes such as precipitation and ion-exchange or removed biologically [6,7].Depending on the distance to agricultural fields, direct reuse of nutrient rich anaerobic effluent is possible if it is treated to remove pathogens and micro-pollutants [8,9].
With an average load of 62 gCOD/p/d and a methanisation level of 60% [10], 12.5 L CH 4 /p/d can be produced from black water (0.35 L CH 4 /gCOD, (Standard temperature and pressure (STP))).When solid kitchen refuse is included ((60 gCOD/p/d), [10]) the biogas production can be doubled, resulting in 25 L CH 4 /p/d, which represents 335 MJ/p/y (35.6 MJ/Nm 3 CH 4 ).Combined heat and power (CHP) generation systems can be used to produce heat and electricity at an efficiency of 85% (of which 40% electricity and 60% heat) [11].This would result in a production of 32 kWh/p/y electricity (2.1% of the electricity consumption in a household (87 PJ electricity consumption in The Netherlands in 2006 [12] i.e., 1487 kWh/p/y)) and 47 kWh/p/y of heat when using the methane produced from black water and solid kitchen refuse.
The use of three types of reactors for anaerobic treatment of black water collected with vacuum toilets at different temperatures is reported in literature, namely a CSTR (continuously stirred tank reactor), an Accumulation system and a UASB-septic tank (Upflow anaerobic sludge blanket).
Wendland et al. [13] investigated anaerobic treatment of black water from vacuum toilets in a CSTR operated at mesophilic conditions (37 °C).A removal efficiency of total COD of 61% was achieved at an HRT (Hydraulic retention time) of 20 days.Applying a CSTR for anaerobic treatment of black water (7 L/p/d) requires a volume of 140 L per person [13].
Kujawa-Roeleveld et al. [10] investigated anaerobic treatment of black water and kitchen refuse in an accumulation system operated at 20 °C.An accumulation system is a continuously fed reactor and combines digestion and storage in one reactor volume.Stabilization of the black water for 80% was achieved within 150 days.Due to the long storage time a relatively large volume is needed of 1.0 m 3 per person for the treatment of black water.An accumulation system therefore is only suitable for even more concentrated streams (e.g., only faeces (brown water) and kitchen waste) and less suitable for black water [10].
The second system that Kujawa-Roeleveld et al. [10,23] investigated was a UASB-septic tank operated at 15 and 25 °C.UASB reactors enable long sludge retention times (SRT) at relatively short hydraulic retention times (HRT), because biomass retention is accomplished by an internal gas/sludge/liquid separation system [4].A UASB-septic tank is a continuous reactor with respect to the liquid, but accumulates the solids, combining the features of a UASB reactor and a septic tank.The UASB-septic tank removed 61% of the total COD at 15 °C and 78% of the total COD at 25 °C.For sludge stabilization and total reduction of volatile fatty acids (VFA) at 25 °C a minimum volume of 200 L per person is needed, corresponding to an HRT of about 30 days [10].
The reactors mentioned above require relatively large volumes per person (Table 1).Unlike the UASB-septic tank, a UASB reactor without additional space for the accumulation of solids (no septic tank) would require regular sludge removal, but it will reduce the volume of the reactor [4].This is important for application at larger scale where space might be limited.UASB reactors so far have not been investigated for their capability to treat concentrated wastewater streams such as black water and was only shortly discussed by Zeeman et al. [14].The volume of a UASB reactor will depend on the minimum SRT required to achieve methanisation and stabilization of the sludge [4].For the anaerobic treatment of black water hydrolysis of particulate organic substrates is the rate-limiting step [15].With first order kinetics and a hydrolysis constant of 0.1 d -1 (average value at 20-30 °C [16]) it can be calculated that a high percentage of hydrolysis (between 80 and 90%) can be achieved at a SRT between 40 and 90 days.Other research showed as well that the minimum SRT was estimated to be 75 days at 25 °C to achieve methanisation and stabilization of the sludge [4,17].Other factors that are important for the anaerobic treatment of black water are the temperature and inhibition by free ammonia [18].Luostarinen et al. [19] investigated the effect of temperature on anaerobic treatment of black water in UASB-septic tanks.The temperature had no significant effect on suspended solids removal, but the removal of dissolved COD improved because sludge adapted to lower temperatures (15 °C) [19].The black water can be produced at a temperature of about 20 °C [20].A higher temperature could result in a shorter HRT, but this would require extra energy requirements for heating the black water.Therefore a temperature of 25 °C was selected for the treatment of black water in a UASB reactor.In concentrated black water high concentrations of ammonium (0.8-1.4 gNH 4 -N/L) are present which can inhibit methanisation and therefore higher retention times could be needed to achieve a maximum production of methane [21].
This paper describes the feasibility of applying a compact UASB reactor for the treatment of concentrated black water from vacuum toilets at these conditions.Furthermore the design of the UASB reactor will be discussed, as well as the minimum volume needed at full scale.

Black water collection
Black water, collected in vacuum toilets, was obtained from the DESAR (Decentralized Sanitation and Reuse) demonstration site in Sneek (Friesland, NL) [22].Every two weeks jerry cans were filled with black water from the buffer tank at the demonstration site (hydraulic retention time of 4 h, not cooled), transported to the lab and stored at 4 °C.Black water was pumped from a stirred, cooled (6 °C) influent tank into the UASB reactor with a Masterflex L/S peristaltic pump.A course filter (4-5 mm holes) in the influent tank prevented clogging of the inlet tube.

UASB reactor
A 50 L flocculent sludge UASB (Upflow Anaerobic Sludge Blanket) reactor (Figure 1) was operated for 951 days at 25 °C to produce biogas from black water.The reactor was made of a transparent Perspex/Plexiglas tube (height: 1.30 m and inner diameter 0.20 m) with a double wall for temperature control.Temperature was controlled with a thermo stated water bath (Haake DC10/K10).The top was made of non-transparent plastic (polypropylene) and served as a gas/solid/liquid separator (height 0.19 m and width 0.22 m).Five taps at different heights (0, 0.26, 0.52, 0.78 and 1.02 m) enabled sludge sampling.Liquid effluent and gas were collected at the top.Gas production was monitored with a gasflow meter (Ritter TG05/5).A magnetic stirrer (VarioMag Mobil) at the bottom of the UASB reactor provided an even distribution of the influent through the sludge bed.The magnetic stirrer only mixed the bottom section of the sludge bed.The reactor was inoculated with 20 L anaerobic sludge (1.1 gVSS/L) from a UASB-septic tank treating concentrated black water at a temperature of 25 °C and a loading rate of 0.42 kgCOD/m 3 /d [23].

Design of the UASB reactor
The HRT to be applied in the UASB reactor was calculated using the following equation proposed by Zeeman and Lettinga [4]: where C is the COD concentration in the influent (COD total , in gCOD/L), SS is the fraction of suspended solids in the influent (COD SS /COD total ), X is the sludge concentration in the reactor (in gCOD/L), R is the fraction of COD SS removed and H is the level of hydrolysis of the removed solids.
Values of C, SS, X, R and H were taken from the research of Kujawa-Roeleveld [16] and this resulted in a design HRT of 6.9 days (Table 2).
Initially the reactor was operated at a longer HRT of 14 days to prevent accumulation of volatile fatty acids (VFA).The first 200 days were used as start-up period and the HRT was subsequently reduced in steps (every 5-6 weeks) when no VFA accumulation was observed.The average HRT achieved was 8.7 days, but fluctuated between 5.8 and 13 days due to silting of the influent tube.The influent tube was cleaned monthly to remove the silted solids.
Sludge was removed regularly from tap 4 at a height of 1.02 m to maintain a maximum sludge bed height of 75% of the reactor volume.

Analyses and measurements
Every week influent and effluent composition was analyzed (125 samples in total) immediately after sample collection.Influent was collected from a tap just before the inlet of the UASB reactor (tap 0, Figure 1) and effluent was collected during 3 hours in the morning (about 0.5-1 L for both samples).COD total was determined from unfiltered samples, filtered COD (COD f ) was determined from paper filtered samples (black ribbon paper filter (Schleicher & Schuell)) and soluble COD (COD soluble ) was determined from membrane filtered samples (0.45 μm membrane filter (Cronus filter PTFE)) using DrLange kits (LCK514).Total Nitrogen (TN) en Total Phosphorus (TP) were determined from unfiltered samples using DrLange kits (LCK238 and LCK350).DrLange kits LCK302 and LCK303 were used to determine the total ammonia nitrogen concentration (NH 4 -N) in paper filtered samples.Ion chromatography (Metrohm 761 Compact IC) was used to measure anions concentrations (Cl -, NO ) and volatile fatty acids (VFA: acetic acid, propionic acid and butyric acid) in membrane filtered samples.ICP-AES (Inductively Coupled Plasma-Atomic Emission Spectroscopy) was used to measure concentrations of the element phosphorus in the membrane filtered sample.Inorganic carbon (IC) was determined with a Shimadzu TOC analyzer by difference from the measured total carbon (TC) and non-purgeable organic carbon (NPOC) in the paper filtered sample.Total Suspended Solids (TSS) and Volatile Suspended Solids (VSS) were determined according to standard methods using black ribbon ashless paper filter (Schleicher & Schuell) [24].Biological oxygen demand (BOD) of the UASB effluent was determined using OxiTop heads calibrated for BOD determination.Depletion of oxygen was monitored for five days (BOD 5 ) (17 samples in total).Biogas composition (sample of 5 mL, 43 samples in total) was analyzed with gas chromatography (Shimadzu GC-2010 Gas Chromatograph containing GS-Q (CO 2 ) and HP molsieve (O 2 , N 2 , H 2 S and CH 4 ) columns).Wasted sludge (51 samples in total) was analyzed for TSS and VSS and total COD using the methods indicated above.Maximum biodegradability of the black water (2 samples in total) and stability of the UASB sludge (13 samples in total) was tested in closed bottles with Oxitop pressure measuring heads by incubation at 37 °C [16].The development of the sludge bed was analyzed by taking sludge samples from every tap (0.2 L) and these samples were analyzed for TSS and VSS and total COD (10 times 5 samples in total).The flow rate in the UASB was measured by weighing the collected effluent over a certain period of time and this was used to calculate the HRT.

Calculations
The concentration of suspended solids COD (COD SS ) was calculated as the difference between COD total and COD f .The concentration of colloidal COD (COD colloidal ) was calculated as the difference between COD f and COD soluble .The SRT in the UASB (SRT UASB ) was calculated using the following equation: where solids reactor is the amount of solids in the reactor (gVSS), solids washed,out is the amount of solids that washed out with the effluent (gVSS/d) and solids wasted is the amount of solids that was wasted manually (gVSS/d).
The total amount of sludge in the reactor was calculated using the analyzed concentration and a volume of 1/6 of 50L as each tap is evenly distributed over the reactor (including effluent 'tap'): where x i is the sludge concentration in gVSS/L of each tap i and i is 0, 1, …, 5.
The COD mass balance was calculated by adding up all measured incoming COD (influent and inoculum sludge) and measured outgoing COD (produced methane, sludge in reactor, wasted sludge and effluent) over the total period of operation including the start-up period.
The amount of produced methane-COD was calculated from the average measured biogas composition, the average gas flow rate (L/d) and a conversion factor of 2.6 gCOD / L CH 4 at 25 °C at standard pressure.
The reported level of methanisation in the UASB reactor was calculated as the percentage of cumulative methane-COD production from the cumulative load of influent COD over the total period of operation.
The level of hydrolysis of solids was determined with the following formula [17] : where COD CH4 is the methane produced, COD soluble,effl is the soluble COD in the effluent, COD soluble,in is the soluble COD in the influent and COD total,in is the total COD load in the influent (all in gCOD).
The rate of hydrolysis was estimated using first order kinetics: [15,25].
Assuming the sludge bed as a CSTR, the following equation can be derived: where F degr is the amount of biodegradable solids in the sludge bed, F degr,0 is the amount of biodegradable solids in the influent and k h is the hydrolysis constant.
is representative for the hydrolysis of suspended solids and therefore representative for the stabilization of the sludge.The bicarbonate concentration was calculated from the total inorganic carbon (IC) as a function of pH and temperature [18].

Performance of the UASB reactor
The composition of the black water influent to the UASB reactor is shown in Table 3.The black water was more diluted in the second period of operation because more flushing water was used in the vacuum toilets due to installation of noise reducers (Table 3) (resulting in a black water production of 7.8 L/p/d instead of 5 L/p/d, [26]).
The maximum biodegradability of the black water was 55% after 70 days of incubation at 37 °C.In Figure 2 the influent and effluent COD concentrations and the total COD removal are shown.The UASB reactor removed an average of 74% of the influent load of COD.The removal efficiency varied between 42 and 94% as shown in Figure 2, and became stable at a value of about 80% from day 500 onward.On average 10 L/d of biogas was produced, consisting of 78% (s.d.5.8%) CH 4 , 22% (s.d.5.7%) of CO 2 and traces of H 2 S (<0.5%).
In Figure 3 the HRT in the UASB is plotted, together with the VFA concentration in the effluent.A few times VFA concentrations in the effluent increased, showing that anaerobic degradation was incomplete.The increase in VFA was always accompanied by a drop in COD removal, but never resulted in complete inhibition of biogas production.Furthermore a thick scum layer in the gas/solid/liquid separator was observed when the VFA concentration increased in the effluent (Figure 3).This scum layer was transferred back to the bottom of the reactor and was no longer observed afterwards.

Sludge bed development
Figure 4 shows that the sludge bed developed to a compact sludge bed with concentrations of up to 45 g VSS/kg sludge.In the first few weeks, part of the inoculum sludge was washed out with the effluent, which explained the high effluent COD concentrations of 16-18 gCOD/L (Figure 2).Gradually the sludge adapted to a higher upflow velocity and the sludge bed increased in volume and concentration.After day 800 sludge had to be wasted less frequently because the sludge concentration increased.The ratio of VSS/TSS of the wasted sludge decreased after day 800 from 0.80 to 0.68 (Figure 4).
The SRT was estimated at 254 days and on average the reactor contained 19 gVSS/L reactor (s.d.4.0) and 34 gCOD/L reactor (s.d.8.0).The wasted sludge from the UASB reactor showed a stability of 91% in 106 days at 37 °C, which means that only 9% of the COD in the UASB sludge could still be converted to methane.The percentage of influent suspended solids that were hydrolyzed and converted to methane was 53%.
The structure and the colour of the sludge changed from black, fine flocculant sludge in the inoculum to a brown, compact muddy sludge.This change in colour was probably due to leaching of iron, because the inoculum sludge originated from a UASB-septic tank where iron was added to precipitate phosphate (data not shown).

COD mass balance
The COD mass balance over the total period of operation (951 days) showed only a small difference between total incoming COD and total outgoing COD (4%) (Figure 5), which probably can be explained by errors introduced by sampling and analyses.Maximum 1% of total incoming COD left the reactor with effluent as dissolved methane (using a maximum solubility of 22 mg CH 4 /L, [27]).

Effluent composition
Table 4 shows the effluent composition of the UASB reactor.The pH dropped from 8.8 / 8.6 (Table 3) in the influent to 7.6 / 7.4 in the effluent of the UASB during the anaerobic treatment.
A fraction of the COD in the effluent was still biodegradable, because the effluent contained a BOD 5 concentration of 0.87 g/L in the first period and 0.48 g/L in the second period.
Nitrogen was conserved for more than 91% in the liquid effluent, mainly as ammonium, and the effluent contained 1.8 gTN/L (of which 1.5 gNH 4 -N/L) in the first period and 1.2 gTN/L (of which 1.0 gNH 4 -N/L) in the second period.Phosphorus was conserved for 61% in the effluent, mainly as phosphate, and the effluent contained 0.13 gTP/L (of which 0.092 gPO 4 -P/L) in the first period and 0.094 gTP/L (of which 0.069 gPO 4 -P/L) in the second period.

Removal efficiency of the UASB reactor
This research shows that anaerobic treatment of concentrated black water can successfully be achieved in a UASB reactor.Generally the reactor exhibited a stable operation and removed more than 78% of the incoming COD.On three occasions VFA accumulated in the effluent and this was probably due to a sudden increase in load due to higher influent concentrations.In those periods scum formation was observed, which was probably caused by the reduced conversion efficiency of the anaerobic treatment process that led to a temporary accumulation of VFA [17].In the concentrated black water the free ammonia concentration was as high as 485 mgNH 3 -N/L (25 °C, pH 8.8, 1.4 gNH 4 -N/L) and reduced in the effluent to 35 mgNH 3 -N/L (25 °C, pH 7.5, 1.5 gNH 4 -N/L).It is likely that inside the UASB reactor a pH gradient exists and shock loads may have caused a temporary inhibition of the methanogenesis by free ammonia [21], resulting in a reduced efficiency.The decrease in pH in the UASB reactor was probably caused by the production of CO 2 which dissolves in the liquid phase.The concentrated black water, however, contains enough alkalinity and pH control is therefore not necessary [18].
Almost all suspended solids were retained in the reactor (93%, Table 5) and high sludge bed concentrations were obtained.After day 800 the sludge contained more inorganic material than before because the ratio of VSS/TSS of the wasted sludge decreased from 0.80 to 0.68 and the sludge bed concentrations increased from about 20 gVSS/kg sludge to 30-45 gVSS/kg sludge (Figure 4).This was probably because the concentrated black water contained more calcium than before (80 mg/L instead of 40 mg/L) and this caused more inorganic precipitation with carbonate and/or phosphate than before [25].In Table 5 the operational characteristics of the UASB reactor are compared with the operation in a UASB-septic tank.In comparison with a lab scale UASB-septic tank a similar removal efficiency (78%, Table 5) and effluent quality (not shown) were obtained, but the applied loading rate in the UASB reactor was much higher (1.0 kgCOD/m 3 /d) than in the UASB-septic tank (0.42 kgCOD/m 3 /d).
Recently the anaerobic treatment of concentrated black water was also investigated at pilot scale in a UASB-septic tank by Meulman et al. [20], but the applied loading rate was much lower (0.36 kgCOD/m 3 /d).The removal efficiency in this UASB-septic tank was higher (87%, Table 5), because the concentrated black water did not pass a coarse filter as within this study and therefore contained a higher amount of suspended solids [20].

Design of the UASB reactor
Design values from Lettinga and Hulshoff Pol [28] show that treatment in a UASB is not recommended for wastewaters with high amount of suspended solids and high concentrations of organic material.These design values do not take into account that hydrolysis is the rate-limiting process and therefore a long SRT is needed for stabilization of the solids and sludge inside the UASB.Based on the fact that the hydrolysis is the rate limiting step, Zeeman and Lettinga [4] derived the formula for calculation of the HRT (equation 1).
An unexpected long SRT of 254 days was achieved in the present research and a large amount of sludge could be retained in the reactor (average of 19 gVSS/L reactor , 34 gCOD/L).Because of this long SRT, the hydrolysis of influent suspended solids (53%) is close to the maximum biodegradability of the suspended solids in the black water (55%).Assuming that the same amount of sludge can be retained in the reactor, the design of the UASB reactor can be optimized.A shorter SRT will result in a lower percentage of hydrolysis and therefore less stabilized sludge, which is illustrated hypothetically in Figure 6.A shorter SRT also means a shorter HRT and therefore the reactor volume can be further reduced at the expense of less stabilized sludge and less biogas production.This can be illustrated using equations 1 and 6.For example a reduction of the volume by reducing the SRT to 75 days will result in 8.2% reduction of the hydrolysis (1-F/F0 reduces from 96.4% to 88.2%), resulting in a hydrolysis of 49%.This reduction in hydrolysis means that 4% of the suspended solids are not hydrolysed and converted to methane.On the total methane production this is a reduction of 5%.As was described in the introduction, the minimum SRT was estimated to be 75 days at 25 °C to achieve methanisation and sufficient stabilization of the sludge [4,17].
A large reduction in volume can be achieved at the expense of a small reduction in hydrolysis of the suspended solids.Using equation 1 the minimum reactor volume for application at full scale can be estimated.Values for X, SS, R and H were adjusted using the results of this research and the conditions at full scale (Table 6).The concentrated black water composition reported by Meulman et al. [20] was used, because in this research it appeared to be impossible to feed all the suspended solids of the black water to a lab scale reactor.Furthermore Meulman et al. [20] showed that the production of concentrated black water is only 5 L/p/d instead of the expected 7 L/p/d.Using adjusted values for the parameters of equation 1 the minimum reactor volume for application at full scale would be 63 L/p (based on 5 L/p/d) corresponding to an organic loading rate of 1.3 kgCOD/m 3 /d (Table 6).This is a significantly lower reactor volume and higher load than when a CSTR or UASB-septic tank is applied for the anaerobic treatment of concentrated black water (Table 1).Application in practice is needed to confirm these estimations.Currently this is tested at the DESAR demonstration site in Sneek (the Netherlands).The non-hydrolyzed suspended solids left in the wasted sludge could be used for aerobic composting, including garden waste, to remove pathogens and to produce a soil conditioner [29] provided that it is safe with respect to heavy metals and micro-pollutants [30].

Fate of nutrients and further treatment
When direct reuse in agriculture of the anaerobic effluent is not feasible because of long distances between cities and agriculture, treatment of the anaerobic effluent is required before the wastewater can be discharged to surface waters.The effluent of the UASB reactor still contains 1.2-2.4gCOD/L, of which part could be removed by aerobic treatment.Furthermore this stream still contains pathogens and hormones and pharmaceutical residues.
Nitrogen was for more than 91% conserved in the effluent, mainly in the form of ammonium.Because nitrogen is not a limiting compound the choice to recover or remove nitrogen from wastewater will depend on the energy requirements.For the nitrogen concentration in black water (about 1.5 kgN/m 3 ) biological removal is preferred [31].Techniques such as a one or two reactor nitritation-anammox process are available to remove ammonium from wastewater streams with a low COD/N ratio [32] and results show that a one or two reactor nitritation-anammox process is suitable to treat the effluent from the UASB reactor [33,34].
For phosphorus a conservation of 60% was observed.The removal of 40% is mainly due to the removal of suspended solids.Probably part of the released phosphate during degradation of the solids directly precipitated in the UASB reactor [35].Detailed analysis of the sludge fraction is needed to close the phosphorus balance.Similar phosphorus conservation in the effluent was found by Kujawa-Roeleveld et al. [23] in the UASB-septic tank.The degree of phosphorus conservation is most likely related to the pH and degree of dilution of the black water.In a UASB reactor on more diluted black water a much higher phosphorus conservation in the liquid effluent stream of 95% was observed (toilets used 5L of water per flush) [36].Phosphorus is a limiting resource and the available phosphorus resources become increasingly scarce [6,37].Depending on the degree of phosphorus conservation during the anaerobic treatment, phosphorus can be recovered from the sludge or from the effluent in the form of struvite (MgNH 4 PO 4 .6H 2 O) [38].Preliminary results show that struvite precipitation in the UASB effluent occurred at relatively low pH of 8 by addition of magnesium.
Further research will focus on the subsequent removal and recovery of the nutrients nitrogen and phosphorus and on the removal of the remaining micro-pollutants such as hormones and pharmaceutical residues.

Conclusions
Anaerobic treatment of concentrated black water in a UASB reactor was successfully achieved at a HRT of 8.7 days and a load of 1.0 kgCOD/m 3 /d.Due to high sludge concentrations (19 gVSS/L reactor ) a long SRT of 254 days was achieved and 53% of the suspended solids were hydrolyzed to methane.The effluent of the UASB reactor needs further treatment to remove remaining COD (2.4 gCOD/L, BOD 5 is 0.87 g/L) and to remove and/or recover nutrients nitrogen and phosphorus.
On the expense of a lower hydrolysis of 49% and some less stabilized sludge, the design of the UASB reactor was optimized and the minimum reactor volume at full scale was calculated to be 63 L/p for black water containing 16 gCOD/L produced at 5 L/p/d.program of the 'Samenwerkingsverband Noord-Nederland".The authors like to thank the participants of the theme "Separation at Source" for their interest and financial contribution.

Figure 2 .Figure 3 .
Figure 2. Influent and effluent COD concentrations and the COD total removal of the UASB reactor.

Figure 4 .
Figure 4. Sludge bed development (upper graph), the amount of sludge wasted (lower graph) and VSS/TSS ratio of the wasted sludge (lower graph).

Figure 5 .
Figure5.COD mass balance over the total period of operation (951 days).The total amount of COD fed to the reactor during this period was 49 kgCOD, of which 0.1% was inoculum sludge.

Figure 6 .
Figure 6.Stabilisation of the sludge represented by 1-F/F0 as a function of the SRT (equation 6, hypothetical, k h is 0.1 d -1 ).

Table 1 .
Reactors for anaerobic treatment of concentrated black water.
n.d.= not determined *calculation based on obtained methane production and influent load

Table 2 .
Initial design values for the UASB reactor.

Table 3 .
Composition of the black water influent.

Table 5 .
Operational characteristics of anaerobic treatment of concentrated black water at 25 °C; (standard deviation).

Table 6 .
Adjusted design values for the UASB reactor.