Mussel Shell-Supported Y tt rium-doped Bi 2 MoO 6 Composite with Superior Visible-Light Photocatalytic Performance

: A series of Y tt rium (Y)-doped Bi 2 MoO 6 composites with calcined mussel shell powder (CMS) as supports were synthesized using a solvothermal method. The as-prepared samples were analyzed using multiple techniques to investigate their microscopic morphology, composition structure, and optical properties. The photocatalytic performance of the as-prepared samples was assessed via examining their capacity to degrade Rhodamine B (RhB) under visible-light irradiation. The photocatalytic data showed that the Y-doped Bi 2 MoO 6 /CMS composites exhibited be tt er photo-catalytic activity compared to pure Bi 2 MoO 6 and undoped Bi 2 MoO 6 /CMS samples. Among the samples, the 0.5%Y-doped Bi 2 MoO 6 /CMS (0.5%Y-BC) showed the highest photocatalytic activity, achieving a maximum degradation rate of 99.7% within 60 min. This could be a tt ributed to highly reactive sites due to Y doping, a narrower band gap, and a lower recombination rate of photoinduced electron–hole pairs. Additionally, the 0.5%Y-BC photocatalyst exhibited excellent stability and reusability properties even after four cycles, making it suitable for practical applications. The ﬁ ndings provided a feasible synthesis of nanocomposite photocatalysts with outstanding properties for organic pollutant removal from the solution system.


Introduction
Environmental pollution caused by organic dyes has been a longstanding and pressing concern, prompting researchers and scientists to seek effective wastewater treatment methods [1].Among the various technologies available, photocatalytic technology has emerged as a promising method for pollution control due to its numerous advantages, including its ease in preparation, cost-effectiveness, minimal energy consumption, remarkable degradation efficiency, and outstanding safety and stability [2][3][4][5][6][7].As a result, research on photocatalytic materials has become a central focus [8,9].
Bismuth molybdate (Bi2MoO6) has garnered significant attention as a photocatalyst due to its unique layered structure.The structure consists of [Bi2O2] 2+ slices and MoO6 octahedra that share corner oxygen atoms [10].The conduction band in Bi2MoO6 is primarily composed of Mo3d orbitals, while the valence band is formed via the hybridization of Bi 6s and O2p orbitals [11].This special band structure results in Bi2MoO6 having a relatively narrow band gap ranging from 2.5 to 2.9 eV [12].Additionally, Bi2MoO6 exhibits exceptional chemical stability, non-toxicity, and good corrosion resistance, making it a promising candidate in the field of photocatalysis [13,14].However, its high recombination rate of photo-generated electron and hole pairs leads to poor catalytic performance, limiting its application [15].To enhance the efficiency of Bi2MoO6 in photocatalytic reac-Citation: Cai, L.; Zhou, Y.; Guo, J.; Sun, J.; Ji, L. Mussel Shell-Supported Yttrium-doped Bi2MoO6 Composite with Superior Visible-Light Photocatalytic Performance.Water tions, various modification techniques have been utilized, including morphological control, semiconductor combination, and element doping [16].Among these approaches, element doping is a commonly used method to reduce the band gap energy and inhibit the recombination of photo-generated electrons and holes [17,18].
Rare earth ions possess a rich 4f electron configuration, and exhibit unique optical properties that have the potential to improve the photocatalytic activity of semiconductors [19,20].Due to their similar ionic radii to bismuth ions, rare earth metal ions can be easily dispersed in Bi2MoO6, making them an effective approach to improve photocatalytic activity [21].Several experiments have been carried out to evaluate the photocatalytic efficiency of Bi2MoO6 doped with rare earth metals such as Eu, Zr, Ce, Ho, Yb, Gd, Lu, Tb, Er, and Sm [22][23][24][25].Among these metals, yttrium has gained attention due to its favorable characteristics, including increased photo absorption capacity and the ability to trap photo-excited electrons.These attributes can assist in reducing the rate of photogenerated electron-hole pair recombination in the photocatalyst [26,27].For instance, in a study conducted by Vaddi et al., it was shown that doping ZnO nanorods with yttrium resulted in a significant reduction in their bandgap, which in turn led to an improvement in their photodegradation activity [28].Similarly, Vadivel et al. used a solvothermal method to synthesize Yttrium-doped BiOF/RGO, and found that Y 3+ ions had a synergistic effect in reducing the electron-hole recombination rate of BiOF with RGO [29].However, to the best of our knowledge, no study has been carried out on Yttrium-doped Bi2MoO6.
In recent years, the utilization of waste biomass materials for the preparation of photocatalyst supports has become a central research topic due to their low cost, high efficiency, and renewability [30][31][32][33][34], such as egg shell [35], coconut shell [36], and mussel shell [37][38][39].Among these, mussel shell, a major byproduct of the mussel aquaculture industry, is usually discarded, leading to environmental pollution.However, mussel shell is naturally biomineralized material, characterized by a substantial presence of calcium carbonate and a distinctive "brick-mud" structure [40,41].Moreover, they contain various trace metal elements, rendering them well-suited for the development of high-valueadded products [37,42].Several studies have indicated that shells could serve as carriers for photocatalysts due to their special microstructure [37][38][39].The trace metal elements in the shell can act as modifiers to enhance the catalyst's performance [37].Our previous study has demonstrated that the mussel shell can effectively disperse the photocatalyst and prevent its aggregation, to enhance electron transport and improve the photocatalytic activity [43].We intended to further enhance the photocatalytic performance of the composite catalyst by doping rare earth elements.
In this study, we prepared a novel ternary Y-doped Bi2MoO6/CMS composite using the solvothermal method.We examined the effect of yttrium content on the chemical composition, morphology, and optical properties.Additionally, we evaluated the photocatalytic activities, stability, and reusability of samples via degrading RhB under visible light irradiation.Finally, we explored the photocatalytic degradation mechanism through active species trapping experiments.

Materials
The mussel shells were collected from Shengsi Shunda Seafood Co., Ltd. in Zhejiang Province, China.They were washed thoroughly with distilled water to remove any surface impurities.

Preparation of Y-Doped Bi2MoO6/CMS Photocatalyst
Initially, the pretreated mussel shells were immersed with 0.1% HCl for 24 h, washed with distilled water until neutral, and dried at 80 °C in the oven for 4 h.The dried mussel shells were calcined at 900 °C for 3 h in a tube furnace with high-purity nitrogen (N2, 99.99%) flowing into the furnace at a rate of 100 mL/min.The resulting calcined sample was cooled, ground into powder (100 mesh), and named CMS.
Next, 0.363 g Bi(NO3)•5H2O and 0.0907 g Na2MoO4•2H2O were dissolved in a 7 mL ethylene glycol solution via sonication for 30 min.Different amounts of Y(NO3)3•6H2O were dissolved in 10 mL absolute ethanol, and slowly added dropwise to the Bi-Mo solution to obtain a mixed solution I with a molar ratio of Y to Bi of 0.063%, 0.125%, 0.25%, 0.5%, and 1%, respectively.Simultaneously, 0.1306 g CMS powder was dispersed in 10 mL of absolute ethanol for 1 h using ultrasonic treatment.The prepared solution I was then slowly added to the CMS suspension under continuous stirring for 2 h to obtain a mixed solution II.The mixed solution II was transferred into a 50 mL Teflon-lined stainless-steel autoclave, heated at 160 °C for 12 h, and cooled to room temperature.Finally, the as-prepared sample was filtered, washed with absolute ethanol and deionized water several times.Then, the material was dried in an oven at 60 °C for 12 h, and further pyrolyzed at 400 °C for 120 min in a tube furnace under a nitrogen atmosphere, while the heating rate was set at 10 °C/min at a nitrogen flow rate of 100 mL/min to produce the Y-doped Bi2MoO6/CMS composite.Different molar ratios of Y to Bi were prepared using a similar method and named 0.063%Y-BC, 0.125%Y-BC, 0.25%Y-BC, 0.5%Y-BC, and 0.1%Y-BC, accordingly.As a reference, pure Bi2MoO6 was synthesized under a similar procedure without the addition of CMS and Y(NO3)3•6H2O, and Bi2MoO6/CMS was synthesized without the use of Y(NO3)3•6H2O.

Characterization
The surface morphologies of the samples were examined using scanning electron microscopy (SEM, Hitachi S-4800, Tokyo, Japan).The specific surface areas and pore size distribution of the samples were analyzed using a Micromeritics ASAP 2010 instrument (Micromeritics Instrument Ltd., Atlanta, GA, USA) and calculated via the BET method.To characterize the functional groups and crystal structure of the samples, Perkin Elmer Fourier transform infrared spectrometer (FTIR, Thermo Scientific Nicolet IS 50, , Waltham, MA, USA) and X-ray diffraction (XRD, Rigaku Ultima IV, Tokyo, Japan) with Cu Ka radiation (V = 30 kV, I = 25 mA) were employed, respectively.The X-ray photoelectron spectroscopy (XPS, ThermoScientific Escalab 250 Xi, Waltham, MA, USA) with Al Ka X-ray radiation was used to analyze the existence of elements and their chemical states on the surface of the sample.To monitor the recombination rate of electron-hole pairs, photoluminescence spectra (PL, FLS980 Series of Fluorescence Spectrometers, Edinburgh Instruments, UK) were recorded.Additionally, the optical properties of the samples were analyzed using a UV-vis spectrophotometer and its integral sphere accessories (UV, Shimadzu UV 2600, Kyoto, Japan).

Photocatalytic Activity Test
The photocatalytic activity of Y-doped Bi2MoO6/CMS photocatalyst was tested by conducting the degradation of RhB in a photochemical reactor (PhchemIII, Beijing, China).A 300 W Xenon lamp, equipped with a 420 nm cut-off filter, was employed as the simulative visible light source, and the entire reaction device was maintained at room temperature using a cooling-water-cycle system.Briefly, 20 mg of the as-prepared photocatalyst was mixed with 40 mL of 6 mg/L RhB in a 50 mL glass beaker under magnetic stirring conditions.Before illuminating the visible light, the reaction system of photocatalyst and RhB was kept in the dark for 3 h to establish an adsorption-desorption equilibrium, and illuminated and kept for 1 h.We utilized UV-visible spectroscopy (UV, Shimadzu UV 2600, Kyoto, Japan) to measure the degradation rate of RhB by the photocatalysts, based on the absorbance values of RhB at a wavelength of 554 nm.The degradation efficiency was calculated from Equation (1).The reaction rate was estimated using the Langmuir-Hinshelwood kinetic equation, as shown in Equation ( 2) [44].
where A0 is an initial photocatalytic degradation of RhB and At represents RhB adsorption measured at a definite time.
C0 represents the initial concentration of RhB, while Ct represents the concentration of RhB during the photocatalytic process at the time t.Moreover, K is the reaction rate constant.The direct decomposition of RhB without any catalyst under visible irradiation was omitted.

Cycle Experiment
To evaluate the chemical stability and practical applicability of the as-prepared photocatalyst, we performed a four-cycle degradation of RhB using Y-doped Bi2MoO6/CMS.After each cycle of photocatalytic degradation, the catalyst was collected through centrifugation, washed with deionized water, and dried in an 80 °C oven.The collected photocatalysts were then reused for subsequent cycles of degradation under the same conditions.

Active Species Trapping Experiments
Briefly, 2 mL of isopropanol (IPA, 0.1 mol/L), sodium oxalate (Na₂C₂O₄, 0.1 mol/L) and p-benzoquinone (BQ, 0.1 mol/L) were prepared as scavengers for •OH, h + , and •O2 − species.These scavengers were added to the reaction solution to be degraded before the illumination process, respectively.Through this setup, the active species participating in the photocatalytic reaction were analyzed.

Chemical Composition Analysis
The crystal composition and structure of the as-prepared samples were analyzed using XRD measurements.Figure 1a displays the XRD patterns of the pure Bi2MoO6, CMS Bi2MoO6/CMS, and Y-doped Bi2MoO6/CMS samples.In comparison to the XRD patterns of pure Bi2MoO6 and CMS, those of Bi2MoO6/CMS and Y-doped Bi2MoO6/CMS showed the diffraction peaks of the orthorhombic phase of Bi2MoO6 and the calcite phase of CaCO3.The diffraction peaks at 28.1°, 32.3°, 46.7°, 55.3° and 58.2° were corresponded to the (131), ( 200), (062), (331), and (191) crystal planes of the orthorhombic phase Bi2MoO6 (JCPDS No. 76-2388).Similarly, the diffraction peaks at 29.4°, 35.9°, 43.1°, and 47.4° were attributed to the (104), ( 110), ( 202) and (024) planes of the calcite phase CaCO3 (JCPDS 83-1762).The Y-doped Bi2MoO6/CMS did not show any evident XRD peak of yttrium compounds or other impurities.However, in further amplification of the spectrum (as shown in Figure 1b), a slight shift to lower 2θ values was observed in the peak corresponding to the (131) crystal plane after Y doping.This shift indicated the substitution of some Bi 3+ with Y 3+ ions, which was an indication of the insertion and substitution of the Bi with rare earth ions in the lattice of Bi2MoO6 [45][46][47].Furthermore, the crystallite size of different samples was calculated using the Scherrer equation [48], and the results are presented in Table 1.The crystalline size of Bi2MoO6 was reduced in comparison to undoped Bi2MoO6/CMS.This suggested that the introduction of Y 3+ ions hinder the growth of Bi2MoO6 in the composite.This was because the insertion of Y in Bi2MoO6 created lattice defects, which further prevented the growth of Bi2MoO6 [49][50][51].A suitable amount of lattice defects can serve as efficient photo-electron-hole capture centers, thereby promoting the separation of photogenerated electron-hole pairs and enhancing the photocatalytic activity of the catalyst [52,53].The XPS testing was used to investigate the surface chemical composition of Bi2MoO6/CMS and Y-doped Bi2MoO6/CMS samples, as shown in Figure 2. The results revealed that the Bi2MoO6/CMS and Y-doped Bi2MoO6/CMS samples were composed of Bi, Mo, O, Ca, and C.However, the Y XPS peaks were not detected in the survey spectra due to the low amount of doping and overlap with the Bi 4f peak [45].The high-resolution XPS spectra of Bi 4f show two strong peaks at 164.0 and 158.6 eV (Figure 2b), assigned to Bi4f5/2 and Bi4f7/2, respectively, indicating the trivalent chemical state of Bi [54,55].The Bi peak shifted towards higher binding energy with the increase in the Y doping ratio, suggesting changes in the Bi chemical environment due to Y doping into the Bi2MoO6 lattice and charge transfer between Bi and Y [56,57].Y doping had no significant effect on the Mo element as seen from the Mo3d3/2 and Mo3d5/2 peaks.The fine spectrum of O1s in the XPS spectrum clearly revealed the different forms of O element.As shown in Figure 2, two strong peaks at 530.7 eV and 532.3 eV were attributed to the proximity of O vacancies and lattice O, respectively, and a weak peak at 529.2 eV represented the binding energy of adsorbed O [57,58].The relative content of three forms of oxygen could be determined based on the proportion of peak area, while the oxygen vacancies in the samples showed a significant increasing trend with the increase in Y doping amount.Furthermore, Figure 2d revealed that the binding energies for Y3p3/2 and Y3p1/2 of Y in 0.5%Y-BC were around 301.1 eV and 310.6 eV, respectively, indicating Y 3+ were successfully doped into Bi2MoO6 [45].The FTIR spectrum of samples were presented in Figure 3.The spectrum of Y-doped samples was similar to the undoped samples.The absorption bands at 841, 733, and 565 cm −1 correspond to the stretching vibration of Mo=O, tetrahedral stretching vibration of Mo-O, and bending vibration of MoO6, respectively [59].The band at 450 cm −1 was assigned to the Bi-O stretching vibration [60].Additionally, four peaks at 1794, 1420, 872, and 729 cm −1 were identified as the characteristic peaks of CaCO3 in CMS [61,62].A broad peak in the 3200-3600 cm −1 could be assigned to the O-H stretching vibration, which is due to the water molecule's adsorption on the surface area [27,63,64].No obvious Y-O vibration peak was observed in the spectrum, likely due to the low doping amount of Y 3+ in the samples.

Morphology and Texture Analysis
The morphologies of samples, including pure Bi2MoO6, CMS, Bi2MoO6/CMS, and Ydoped Bi2MoO6/CMS, were characterized using SEM, and the results are presented in Figure 4. Pure Bi2MoO6 exhibited a hollow spherical structure assembled from nanosheets (Figure 4a).The CMS had an irregular block-like structure, with many nanorods on its surface (Figure 4b).Bi2MoO6/CMS exhibited a morphology composed of stacked lamellar nanosheets, primarily supported by CMS (Figure 4c).The morphologies of 0.063%Y-BC and Bi2MoO6/CMS were similar (Figure 4d), indicating that the trace amount of yttrium did not significantly alter the host materials.However, as the doping amount increased, the size of Bi2MoO6 nanosheets decreased.When the doping amount reached 0.5%, the sample displayed a homogeneous sheet-like structure that tended to aggregate into clusters (Figure 4g).Furthermore, at a Y doping concentration of 1%, the particles exhibited an increase in size and thickness, accompanied by a smooth surface (Figure 4h).As shown in Figure 5i, the TEM image of 0.5%Y-BC demonstrated that the Bi2MoO6 nanosheets were attached to the surface of the nanorods of CMS and formed a clustered structure, confirming with the SEM images.Figure 5 displays the N2 adsorption and desorption isotherms, as well as the corresponding pore size distribution curves for Bi2MoO6/CMS and Y-doped Bi2MoO6/CMS samples.The N2 adsorption and desorption isotherms showed that all the samples exhibited type IV isotherms with an obvious H3-type hysteresis loop in the high relative pressure range of 0.9-1.0(P/P0), indicating the presence of mesopores [65,66].The pore size distribution curve measured via the BJH method revealed that the pore width was mainly distributed in the 2-30 nm range.The specific surface areas of Bi2MoO6/CMS, 0.063%Y-BC, 0.125%Y-BC, 0.25%Y-BC, 0.5%Y-BC, and 1%Y-BC were measured to be 28.64, 29.91, 37.94, 38.23, 42.50, and 20.60 m 2 /g (Table 1), respectively, and showed a gradual increase with increasing the doping amount of Y element.The sample with 0.5% doping exhibited the highest specific surface area among all the samples.However, with a further increase in the doping amount, the specific surface area decreases due to the excess Y potentially causing the aggregation of Bi2MoO6 nanosheets or blocking of pre-existing pores.The increase in specific surfaces could enhance the adsorption and degradation of organic pollutants.It also provided more active sites for the photogenerated electrons and holes, leading to an improved photocatalytic performance [24,67].

Optical Properties
The optical properties of the as-prepared samples were measured using UV-vis diffuse reflectance spectroscopy, as shown in Figure 6.All samples exhibited significant absorbance in the visible-light region.Compared to Bi2MoO6/CMS, the Y-doped Bi2MoO6/CMS samples showed a red shift of the absorption edges.The band gap value was calculated using the Kubelka-Munk equation, as follows.
(αhv) 2 where α, hv, A, and Eg are the absorption coefficient, photonic energy, Planck constant, and band gap, respectively [68].Using Equation 3, the curves of these samples were fitted, and the results are presented in the inset of Figure 6.The estimated band gaps of pure Bi2MoO6, Bi2MoO6/CMS, 0.063%Y-BC, 0.125%Y-BC, 0.25%Y-BC, 0.5%Y-BC, and 1%Y-BC were approximately 2.65, 3.00, 2.98, 2.94, 2.92, 2.91 and 2.83 eV, respectively.Notably, the band gap of Y-doped Bi2MoO6/CMS had slightly decreased compared to Bi2MoO6/CMS.This decrease could be due to the charge transfer transition occurring between 4f or 5d electrons of Y elements and the conduction or valence band of Bi2MoO6 [19,69].These findings indicated that Ydoping effectively broadened the light absorption range of the catalyst [45].Consequently, this was considered beneficial for improving the utilization of light photons.The efficiency of the photocatalytic material in dye degradation relies on the effective separation of the photogenerated charge carriers, which could be determined through analysis of the photocatalysts' photoluminescence spectra (PL) [47,70].A lower PL intensity indicated a lower recombination rate of electron-hole pairs, resulting in improved photocatalytic performance [71,72].In Figure 7, the PL spectra of Bi2MoO6/CMS and 0.5%Y-BC were depicted, showing a strong peak at 467 nm due to photoinduced electron transfer transitions between O 2p (VB) and empty Mo 5d orbital (CB) [18].Notably, the peak intensity of 0.5%Y-BC was lower than that of Bi2MoO6/CMS, indicating that the recombination rate of photogenerated electrons and holes in 0.5%Y-BC was lower than that of undoped Bi2MoO6/CMS.

Photocatalytic Degradation of RhB
The photocatalytic activity of pure Bi2MoO6, Bi2MoO6/CMS, and Y-doped Bi2MoO6/CMS photocatalysts were investigated by testing the degradation of RhB solution under visible-light irradiation.In Figure 8a, we observed that RhB had not degraded in the absence of a photocatalyst, indicating its high structural stability.All Y-doped Bi2MoO6/CMS samples exhibited a more efficient photodegradation rate than the undoped Bi2MoO6/CMS and pure Bi2MoO6.The 0.5%Y-BC exhibited the highest photocatalytic performance, achieving a remarkable degradation rate of 99.7% after 60 min of irradiation.
Kinetic studies were conducted using the pseudo-first-order model.Figure 8b shows that 0.5% Y-BC exhibited the highest rate constant, which was three times higher than Bi2MoO6/CMS and ten times higher than pure Bi2MoO6.This is because 0.5%Y-BC has a lower recombination efficiency of photogenerated electrons and holes, higher specific surface area, and lower band gaps.However, the increase in the yttrium content to 1% would result in a lower K value.The former BET surface area analysis shows that Y doping at a high concentration could decrease the surface area.Moreover, the excess Y 3+ ions in 1%Y-BC may act as a recombination center for the photogenerated charges, decreasing the photocatalytic activity [73].Thus, it is important to carefully control the Y 3+ concentration to avoid decreasing the photocatalytic efficiency caused by the recombination of electronhole pairs.Furthermore, a comparison of the photodegradation performance of 0.5% Y-BC with other photocatalysts reported in the literature is presented in Table 2.Although the initial concentration of pollutants in this study was slightly lower than the concentrations reported in the literature, while the K value of the 0.5% Y-BC was significantly higher than that of other catalysts, indicating its superior photocatalytic performance.Figure 9 displays the absorption spectra of RhB over time in the presence of 0.5%Y-BC under visible light.As the irradiation time increased, the absorbance of RhB at 550 nm decreased rapidly.This decrease was accompanied by a blue shift in the absorption band, which is due to the formation of a series of N-de-ethylated intermediates as RhB degrades [76].After 60 min, RhB was entirely degraded, indicating that the dye-conjugated structure of the RhB molecule was destroyed.

Cycle Experiment
The stability and reusability of 0.5%Y-BC was investigated via a recycling experiment, and the results are presented in Figure 10.As shown in Figure 10a, the degradation efficiency of 0.5%Y-BC for RhB decreased slightly, from 99.7% to 83.3%, after four cycles of experiments.Two factors could lead to the decrease in degradation efficiency.Firstly, there could have been a loss of catalyst mass during the centrifugation collection process.Secondly, the adsorption of the intermediate onto the photocatalyst's surface may have resulted in a reduction in the number of exposed reactive sites, leading to a decrease in the removal efficiency for RhB.Additionally, the stability of 0.5%Y-BC was analyzed via XRD, and the results are presented in Figure 10b.Notably, the XRD data revealed that the phase of the 0.5%Y-BC remained unchanged even after four cycles of experiments, indicating its stability and reusability in conducting photocatalytic reactions.

Possible Photocatalytic Mechanism of Photocatalysts
To determine the primary active radicals and explain the photocatalytic mechanism in the photocatalytic degradation of RhB by 0.5%Y-BC, active species trapping experiments were conducted.IPA, Na₂C₂O₄, and BQ were used as scavengers of •OH, h + , and •O2 − , respectively [77].The results, depicted in Figure 11, reveal that the photocatalytic activity of 0.5%Y-BC decreased with the addition of different active species scavengers.Specifically, the introduction of BQ and Na₂C₂O₄ significantly lowered the photocatalytic activity of 0.5%Y-BC, suggesting that •O2 -and h + are the primary active species involved in the RhB degradation by 0.5%Y-BC.We also observed a slight decrease in photocatalytic efficiency with the addition of IPA, indicating that •OH also plays a crucial role in the photocatalytic reaction.The Y 3+ ion significantly enhanced the photocatalytic efficiency of Y-doped Bi2MoO6/CMS through several mechanisms.Firstly, Y doping narrowed the band gap of the photocatalysts, making it easier for photo-excited electrons to move from the CB to VB.Second, Y doping substantially increased the specific surface area of the catalyst (from 28.6385 to 42.4971 m 2 /g), providing more reaction sites and promoting photocatalytic degradation.Thirdly, Y doping triggered the formation of new defect sites and oxygen vacancies, which acted as electron traps to prevent the recombination of electron-hole pairs.Furthermore, mussel shells, as photocatalyst supports, have unique pores and surface structures which could offer more active sites for pollutant attachment in photocatalytic reactions than stacked catalysts [38,43].Moreover, shells contained various trace metal elements (e.g., Se, Mn, Zn, Ti, and Sr) that could serve as doping elements, facilitating electron transfer in photocatalytic reactions, thus enhancing the photocatalytic capability of the composites [37,42].Therefore, CMS and Y 3+ ions synergistically enhanced the performance of composite photocatalysts.
A proposed mechanism, based on experimental results and the literature, explains the possible reactions in photocatalysis, as shown in Figure 12.Under visible light irradiation, Bi2MoO6 was excited, generating electron-hole pairs, with the electrons excited to the conduction band and the holes remaining in the valence band.The presence of Y 3+ on the Bi2MoO6, and its specific electronic configuration with vacant 4d and 5s orbitals, could capture electrons and form Y 2+ , hindering the recombination of electron-hole pairs.And then, these Y 2+ ions reacted with oxygen molecules to produce superoxide radicals (•O 2− ) [78][79][80][81].Simultaneously, the holes in the valence band directly participate in the photooxidation reaction with water molecules to produce hydroxyl radicals (•OH).These active species, i.

Conclusions
In this study, a series of Y-doped Bi2MoO6/CMS was successfully developed via a simple solvothermal method based on the mussel shell.XPS results showed that Y was successfully doped into Bi2MoO6/CMS, and XRD demonstrated that Y-doped Bi2MoO6/CMS consisted of orthorhombic phase Bi2MoO6 and calcite phase CaCO3.Ydoped Bi2MoO6/CMS exhibited superior visible-light-driven catalytic performance in the degradation of RhB solution, as compared to the undoped sample.Specifically, 0.5%Y-BC with excellent stability and reusability showed the maximum degradation rate of 99.7% in 60 min, and •O2 -and h + are the primary active species in the RhB degradation.Moreover, the improved photocatalytic activity of 0.5%Y-BC was mainly attributed to its higher surface area, narrower bandgap, and enhanced separation of electron-hole pairs.Therefore, this study provided a new approach for the high-value utilization of mussel shells, and developing high-performance photocatalysts for removing organic pollutants from wastewater.

Figure 10 .
Figure 10.(a) Recyclability of 0.5%Y-BC for the degradation of RhB under visible light for four cycles; (b) the XRD patterns of the original and recycled 0.5%Y-BC.

Figure 11 .
Figure 11.The effects of photogenerated carriers trapping on photocatalytic degradation activity of 0.5%Y-BC.

Table 1 .
Physico-chemical properties of the prepared photocatalysts.

Table 2 .
Comparison of the photodegradation performance of Y-doped Bi2MoO6/CMS with other photocatalysts reported in the literature.