Risk Assessment and Mapping of Flash Flood Vulnerable Zones in Arid Region, Fujairah City, UAE-Using Remote Sensing and GIS-Based Analysis

: A ﬂash ﬂood is the most common natural hazard that endangers people’s lives, the economy, and infrastructure. Watershed management and planning are essential for reducing ﬂood damages, particularly in residential areas, and mapping ﬂash ﬂood-sensitive zones. Flash ﬂooding is an interface dynamic between geoterrain system factors such as geology, geomorphology, soil, drainage density, slope, and ﬂood, rather than only water movement from higher to lower elevation. Consequently, the vulnerability to ﬂash ﬂoods necessitates an awareness of and mapping topographical features. A ﬂash ﬂood vulnerable zones (FFVZ) map is essential for thorough ﬂash ﬂood risk assessment and management to minimize its detrimental effects, particularly in residential areas, especially in cities like Fujairah with seven wadis ﬂowing into the city and even though it has two main dams and ﬁfteen breaker dams. So, in this work, eight satellite image-derived parameters rainfall, elevation, slope, land use/land cover (LULC), drainage density, geology, geomorphology, and soil were combined to predict the ﬂash ﬂood-vulnerable zones using a weighted overlay technique based on geographic information systems (GIS). Each element of the thematic maps is ranked and weighted according to how vulnerable it is to ﬂash ﬂoods in the study area, with 55 km 2 being classiﬁed as a very highly vulnerable area, 78 km 2 as a high-risk area, 9.3 km 2 as a moderate risk area, 70 km 2 as a low vulnerable area, and 257 km 2 as a very low vulnerable area. In addition, places with a very high vulnerability level include the Fujairah Airport, Fujairah Port, some residential neighborhoods in the city’s center, oil storage areas, two hospitals, and universities. Additionally, from 1990 to the present, Landsat and Sentinel 2 data showed consistent changes in vegetation and built-up areas. Therefore, in addition to helping policy and decision-makers make the best choices about the efﬁcacy of the study area’s protective structures against the risk of ﬂash ﬂoods in the future, the results can also be a valuable source of information.


Introduction
The most frequent natural disasters globally are flash floods, which happen when a lot of rain falls quickly and produces a lot of surface runoff [1][2][3].Flood catastrophes have frequently increased due to climate change and other environmental factors [4].Since most nations are susceptible to flooding, it seriously threatens human life worldwide [5][6][7][8][9][10].Flash floods can inflict damage anywhere, but they are especially destructive close to rivers and in agricultural areas, infrastructure, and human lives [11,12].Globally, flash floods Water 2023, 15, 2802 2 of 30 claim the lives of more than 5000 people each year [2,13].Other factors, including drainage density and slope and a lack of efficient mapping or precautionary measures, may also contribute to this problem.Spatially explicit and catchment-scale flood models will be needed to evaluate landscape change and rainfall runoff scenarios to reduce the effects of flooding natural disasters and preserve healthy socio-ecological systems under changing catchment and climate conditions [14].
According to Jackson and Bates [15] and Sen [16], the Arabic word wadi refers to a dry valley stream generally found in desert regions, such as countries on the Arabian Peninsula.Earlier rainfall in Wadis is primarily episodic, fluctuating greatly in time and space, and many years go by without any rain.However, due to the effects of climate change, wadi flash floods in arid places have recently increased in frequency and severity [17,18].According to [19], who examined pre-and post-flood scenarios using remotely sensed data, flash floods can produce enough runoff in direct response to intense and typically sudden rains for wadis to flow for some distance within the basin.However, the flow frequently does not reach the coast because of high transmission losses.According to the United Nations Office for Disaster Risk Reduction [20] (UNISDR), throughout the past 30 years, several disasters have affected Arabian countries, killed over 150,000 people and had an impact on almost 10 million others [21,22].
Flash floods, particularly in Oman, are frequently brought on by extreme events, such as tropical cyclones, that destroy enormous amounts of infrastructure and kill many people.In addition, Oman was affected by severe tropical cyclone Gonu in July 2007, which caused 54 fatalities and $3.9 billion in property damage [23,24].Egypt has also had a series of flash floods in recent years, most notably in October 2019 and 2015.These floods caused devastating losses in terms of lives lost and property damage in Alexandria, Sinai, and Beheira [25,26].The majority of the Middle East, including Jordan, Kuwait, Qatar, Saudi Arabia, United Arab Emirates (UAE), and Oman, saw severe destruction in October 2018 due to the increased frequency of intense rainfall events linked to numerous flash floods.These floods killed people and animals while destroying the primary infrastructures, including buildings, villages, agricultural lands, roads, electricity towers, and pipelines [27,28].Wadi flooding in 2018 resulted in 4000 tourists fleeing to safer areas less than an hour before the peak flood hit Petra, Jordan's ancient landmark [29].
Additionally, it has been alleged that a flash flood in March 1966 caused roughly 200 fatalities and 250 injuries.Further, 3000 individuals are left homeless [30].In the last ten years, severe flash floods have killed more than 113 people in Saudi Arabia and destroyed 10,000 dwellings [31].Additionally, the northeastern section of the UAE, particularly Fujairah, has had a maximum of 13 floods during the past 20 years [32].
To further the discussion, nations in the Arabian Gulf region have invested in weather modification research and applications in response to the water resource problem, which is worsened by the region's expanding population and changing climate [33].The UAE began running cloud seeding missions for additional rains to fulfil the country's expanding water needs in the previous decade, inspired by the global cloud seeding initiatives.The first of its sort began in the 1990s and modified how much precipitation clouds released [34].The UAE government's official policy on cloud seeding began to be implemented significantly in 2010.This was unavoidable for an arid nation like the UAE, where average rainfall is less than 100 mm and high evaporation rates result in a lack of surface water and an overreliance on non-renewable groundwater resources that have caused aquifers to be depleted [35].The Hajar Mountains in the eastern part of the UAE were specifically identified as having an apparent rise in rainfall intensities after comparing the pre-cloud seeding era (before 2010) and after [36].Even though there is research available about the features of the UAE's rainfall, very few of these studies have looked into whether there is a connection between recent cloud-seeding missions and the rising rainfall intensities and urban flooding that have been seen.
The modeling of flash floods is a crucial tool for managing and mitigating floods [1,[37][38][39][40][41][42].Numerous studies have mapped flood-prone areas using a variety of methodologies, such Water 2023, 15, 2802 3 of 30 as [9,[43][44][45][46] have used traditional morphometric analyses.To prevent future property damage and fatalities from flash floods, flood control design must consider the effects of global warming, especially flash flood hazards in residential areas [47][48][49].To initiate the flash flood vulnerable zones mapping, researchers used several hydrologic, geologic, biological, and climatic elements that affect flash floods in the catchment areas [3,13,39,50].Geology, slope, LULC, drainage density, geomorphology, soil, distance to river, and rainfall distribution map are among the characteristics that are most crucial [51][52][53].Aster satellite image data and GIS can be combined to create flood risk index maps, according to a study by [54].Remote sensing is a useful method to track flood occurrences and pinpoint the hydrogeological settings without maps of flooded areas.The proliferation of satellites has also improved the likelihood of locating flooded areas.Flood risk maps were verified by [55] using free optical and radar satellite images.Eight characteristics, including rainfall, slope, drainage, soil, geological structures, geology, geomorphology, and land use and land cover, were utilized by [51] to simulate the flood danger.Getahun and Gebre [56] employed six variables to simulate the risk of flooding in the Awash River basin in Ethiopia.They used slope, elevation, rainfall, population density, land use, land cover, and soil type.Samanta [57] employed four parameters-elevation, slope, land use, and distance from the river-to create a model for flood danger maps in the vicinity of the Markham River in Papua New Guinea.Mathew Kelly [58] studied thoroughly to assess flood risk for Australia's Hawkesbury-Nepean Catchment.The number of characteristics needed to produce flood-vulnerable maps is generally not set; instead, it varies on the availability of data, the location of the study region, and the significance of the element.
Even though they can be deadly, flash floods can also be helpful because they replenish Fujairah City's parched aquifers and moisten the areas damaged by the drought, as UAE has limited conventional renewable water resources [59].This type of natural hazard cannot be prevented, but it can be successfully controlled with the help of effective flood management strategies like harvesting floodwater and rainfall runoff for human and livestock use as well as agricultural growth while building subterranean dams, artificial lakes, recharge dams, and off-stream structures [25,60].The main goal of this study was to identify the likely flash flood risk zones by examining all potential resource maps.By observing satellite images from the relevant period, the current work pinpoints areas prone to flash floods.GIS facilitates the administration and integration of multi-thematic data.Rainfall, elevation, slope, geology, geomorphology, LULC, soil, and drainage density are some of the thematic layers generated and examined via weighted overlay analysis for this study to identify potential flood-vulnerable areas.Flood-vulnerable maps provide local municipalities and citizens with information on the degree of flood danger in their communities.They can be utilized effectively as an evacuation guide during a flood event.

Study Area
With a total size of 1450 km 2 , Fujairah is the fifth-largest emirate in the UAE [61].The Emirate of Fujairah, one of the seven Sheikhdoms of the UAE, is the only emirate with its entire coastline situated on the Gulf of Oman and defined by a headland bay configuration with several cliffs extending into the Gulf [62].Fujairah City is the capital of this emirate.The Hajar/Oman Mountains, which separate Fujairah from the Gulf of Oman and the Eastern Coastal Plain, are an exceptional feature of the emirate.The research area's highest point is 1103 m above mean sea level.This mountain is the source of numerous Wadis, including Wadi Hayl, wadi Saham, wadi Farfar, wadi Ham, wadi Yabsah, and Wadi Madhab, which flows into Fujairah City.The largest and longest wadi in the UAE, Wadi Ham, has a catchment area of 192 km 2 and extends over 30 km from Masafi in the northwest to the Wadi Ham Dam close to Fujairah City in the southeast.Wadi Saham, Wadi Farfar, and Wadi Yabsah finally debouches in Wadi Ham Dam (Figure 1).Most of the year, the wadi beds are dry, but when it rains, the dry wadi beds turn into rushing rivers, creating a breathtaking spectacle.
northwest to the Wadi Ham Dam close to Fujairah City in the southeast.Wadi Saham, Wadi Farfar, and Wadi Yabsah finally debouches in Wadi Ham Dam (Figure 1).Most of the year, the wadi beds are dry, but when it rains, the dry wadi beds turn into rushing rivers, creating a breathtaking spectacle.According to the demographic figures from the Fujairah Statistics Center (FSC) for 2023, 318,325 people are living in Fujairah, with Fujairah City (study area) housing over 77% of the total population [32].Most of Fujairah City's urban areas are on low coastal plains, making them more vulnerable to flash floods.The UAE Ministry of Energy and Industry, in collaboration with the Ministry of Climate Change and Environment, has issued rules for protection against floods to lessen the effects of flash floods.When planning or building any residential area close to Wadis, they specified several requirements that had to be followed.These communities and government bodies will benefit from this paper's identification of flash flood vulnerable zones.
Fujairah is regarded as one of the UAE's most productive regions, along with the Hajar Mountains, the plains, and some desert regions.Major wadis drop through the Hajar Mountains on either side into the Fujairah, supplying significant floodwater to the neighboring alluvial and coastal plains.Fujairah City, which covers an area of around 559.86 km 2 between 25°17' 31.63N and 25°01' 49.39 N and 56°08' 50.73 N and 56°22' 29.12 N, is included in the current research area, which is a section of the Fujairah emirate that consists of the catchment areas of the seven wadis.It mostly consists of the Fujairah City region, a portion of the Sharjah Emirate's Kalba and Khor Fakkan areas, and a 77 km 2 area of the Sultanate of Oman, as depicted in (Figure 1).In the northern and southern portions of the study area, the Fujairah city area is characterized by narrow coastal plains that range in width from 1 to 3 km and are at their widest in Al-Qurayyah and Skamkam.Lithologically, the Jurassic to Cretaceous igneous and metamorphic rocks are found in the north and west, and alluvial deposits at the foot of the mountains dominate the higher streams [63].The study area experiences various meteorological conditions, including cold to mild in the winter and hot to humid in the summer.In the western mountainous regions, the annual rainfall ranges from 80 mm to 160 mm [64].Approximately 97% of the total yearly rainfall in the northern section of the UAE was thought to fall over the eastern mountainous and coastal regions [64].The region typically has dry weather with 100-250 mm According to the demographic figures from the Fujairah Statistics Center (FSC) for 2023, 318,325 people are living in Fujairah, with Fujairah City (study area) housing over 77% of the total population [32].Most of Fujairah City's urban areas are on low coastal plains, making them more vulnerable to flash floods.The UAE Ministry of Energy and Industry, in collaboration with the Ministry of Climate Change and Environment, has issued rules for protection against floods to lessen the effects of flash floods.When planning or building any residential area close to Wadis, they specified several requirements that had to be followed.These communities and government bodies will benefit from this paper's identification of flash flood vulnerable zones.
Fujairah is regarded as one of the UAE's most productive regions, along with the Hajar Mountains, the plains, and some desert regions.Major wadis drop through the Hajar Mountains on either side into the Fujairah, supplying significant floodwater to the neighboring alluvial and coastal plains.Fujairah City, which covers an area of around 559.86 km 2 between 25 • 17' 31.63N and 25 • 01' 49.39 N and 56 • 08' 50.73 N and 56 • 22' 29.12 N, is included in the current research area, which is a section of the Fujairah emirate that consists of the catchment areas of the seven wadis.It mostly consists of the Fujairah City region, a portion of the Sharjah Emirate's Kalba and Khor Fakkan areas, and a 77 km 2 area of the Sultanate of Oman, as depicted in (Figure 1).In the northern and southern portions of the study area, the Fujairah city area is characterized by narrow coastal plains that range in width from 1 to 3 km and are at their widest in Al-Qurayyah and Skamkam.Lithologically, the Jurassic to Cretaceous igneous and metamorphic rocks are found in the north and west, and alluvial deposits at the foot of the mountains dominate the higher streams [63].The study area experiences various meteorological conditions, including cold to mild in the winter and hot to humid in the summer.In the western mountainous regions, the annual rainfall ranges from 80 mm to 160 mm [64].Approximately 97% of the total yearly rainfall in the northern section of the UAE was thought to fall over the eastern mountainous and coastal regions [64].The region typically has dry weather with 100-250 mm precipitation per year [32,[65][66][67].During the winter and summer, Fujairah's typical temperatures range from 15 to 47 degrees Celsius.

Factors Leading to Study and Mapping the Flash Flood Vulnerable Zones in Fujairah City
The UAE has attracted many immigrants since its founding in 1973, who have significantly changed the country's geography.The demand for these individuals matched the economic growth from the massive oil profits [68].Before 1980, Fujairah had an insignificant demographic situation, with a population of only 32,000.At this time, the majority of Fujairah city was made up of people who were mostly engaged in commerce and fishing.Since the current economic boom began 43 years ago, Fujairah Emirate's population has multiplied dramatically (Figure 2).Fujairah had 32,000 residents in 1980; that number has increased to 150,000 in 2010 and, by 2023, around 318,325.Based on its annual growth rate, Fujairah's population is among the fastest-growing in the region.

Factors Leading to Study and Mapping the Flash Flood Vulnerable Zones in Fujairah City
The UAE has attracted many immigrants since its founding in 1973, who have significantly changed the country's geography.The demand for these individuals matched the economic growth from the massive oil profits [68].Before 1980, Fujairah had an insignificant demographic situation, with a population of only 32,000.At this time, the majority of Fujairah city was made up of people who were mostly engaged in commerce and fishing.Since the current economic boom began 43 years ago, Fujairah Emirate's population has multiplied dramatically (Figure 2).Fujairah had 32,000 residents in 1980; that number has increased to 150,000 in 2010 and, by 2023, around 318,325.Based on its annual growth rate, Fujairah's population is among the fastest-growing in the region.
Regarding the study area, I, e, Fujairah City, which is 560 km 2 , the Hajar Mountains occupy roughly 403 km 2 to the west.Therefore, the city of Fujairah's constantly growing population will have to reside in just 157 km 2, which is considered a challenge.As was already said, due to its closeness to the airport, schools, universities, shopping malls, and other significant facilities, over 77% of the population of the Fujairah emirate resides in Fujairah city [32].Urban sprawl's extensive and rapid growth is a crucial indicator of population growth [69].Increasing urban built-up areas and an increasing global population, particularly in coastal regions, have given rise to large cities.The LULC maps created with Landsat images from 1990, 2000, 2010, and Sentinel-2 from 2023 showed high levels of built-up growth in Fujairah (Figure 3).Urban waterlogging regions are growing more quickly and in size due to the expansion of urban sprawl, which has increased the impermeable surface area that prevents rain from penetrating the underlying soil.Over the previous 30 years, there has been a significant shift in the land use and cover in the Fujairah area (Figure 3), which could have increased the runoff coefficient.In the past 23 years, Fujairah City has seen more floods than any other place in the emirate of Fujairah, according to [32].Other flooding causes include the extension of residential areas, making it harder for natural flows and drainage systems to remove surplus water after heavy rains.However, in recent years, human interference has given it a new dimension [70,71].
As seen in Figure 3, the study area's built-up in 1990 covered an area of about 40 km 2 , mostly in the south and northeastern parts of Fujairah City, mainly consisting of built-up Regarding the study area, I, e, Fujairah City, which is 560 km 2 , the Hajar Mountains occupy roughly 403 km 2 to the west.Therefore, the city of Fujairah's constantly growing population will have to reside in just 157 km 2, which is considered a challenge.As was already said, due to its closeness to the airport, schools, universities, shopping malls, and other significant facilities, over 77% of the population of the Fujairah emirate resides in Fujairah city [32].Urban sprawl's extensive and rapid growth is a crucial indicator of population growth [69].Increasing urban built-up areas and an increasing global population, particularly in coastal regions, have given rise to large cities.The LULC maps created with Landsat images from 1990, 2000, 2010, and Sentinel-2 from 2023 showed high levels of built-up growth in Fujairah (Figure 3).Urban waterlogging regions are growing more quickly and in size due to the expansion of urban sprawl, which has increased the impermeable surface area that prevents rain from penetrating the underlying soil.Over the previous 30 years, there has been a significant shift in the land use and cover in the Fujairah area (Figure 3), which could have increased the runoff coefficient.In the past 23 years, Fujairah City has seen more floods than any other place in the emirate of Fujairah, according to [32].Other flooding causes include the extension of residential areas, making it harder for natural flows and drainage systems to remove surplus water after heavy rains.However, in recent years, human interference has given it a new dimension [70,71].
from 2000 to 2023 is shown in Figure 4.The Fujairah Airport opened in 2010 due to tre mendous development in Fujairah.During this time, the area of the Fujairah port ex panded, as well as other significant commercial sectors, bringing the total built-up area to 88 km 2 .Finally, the urban sprawl reached 115 km 2 in 2023, with most construction focused on growing residential areas to serve the continuously growing population, along with other facilities like shopping centers, universities, schools, etc.As seen in Figure 3, the study area's built-up in 1990 covered an area of about 40 km 2 , mostly in the south and northeastern parts of Fujairah City, mainly consisting of built-up residential and plantation areas.Urban sprawl reached 51 km 2 in 2000, with growth moving further to the north-western corner of the study area consisting of residential and plantation areas.The major change in the infrastructures (built-up) in the study area recorded from 2000 to 2023 is shown in Figure 4.The Fujairah Airport opened in 2010 due to tremendous development in Fujairah.During this time, the area of the Fujairah port expanded, as well as other significant commercial sectors, bringing the total built-up area to 88 km 2 .Finally, the urban sprawl reached 115 km 2 in 2023, with most construction focused on growing residential areas to serve the continuously growing population, along with other facilities like shopping centers, universities, schools, etc.The Northern part of UAE, which includes the study area, has recently seen multiple flash flooding incidents.Lately, the Eastern parts of UAE, Ras Al Khaimah (200 mm), Masafi (209.7 mm), and particularly Fujairah Port (inside the study area) recorded the highest rainfall of 234.9 mm, and Fujairah Airport with (153 mm), between the 25 July and 28 July 2022, according to reports on [72] The Gulf Today and The National News [73], respectively.Because of the unusually heavy rains and the presence of seven wadis in Fujairah City, namely Wadi Hayl, wadi Saham, wadi Farfar, wadi Ham, wadi Yabsah, wadi Madhab, and Wadi Safad (Figure 1), affecting total of 4225 people and were evacuated with the help of 1638 personnel who got affected by the flooding that occurred within these wadis and also water that was spilling over the southern side of the Wadi Ham Dam, which is inside the Fujairah city (Figure 5).Approximately 870 individuals were saved, and another 3897 people were given shelter [72] (Gulf Today, 2022).The world's thirdlargest fuel bunker canter, Fujairah Port, was also affected by widespread flooding [74].
Similarly, to this, the floods had a significant negative impact on residential areas, agriculture/plantations, numerous automobiles, hospitals, schools, and electrical lines [75].Since the majority of Fujairah City's key districts were affected, it is crucial to investigate the specific causes of these significant losses in addition to the high rainfall.This work has been done to identify flashflood-sensitive zones in Fujairah City while considering the seriousness of the problem.The Northern part of UAE, which includes the study area, has recently seen multiple flash flooding incidents.Lately, the Eastern parts of UAE, Ras Al Khaimah (200 mm), Masafi (209.7 mm), and particularly Fujairah Port (inside the study area) recorded the highest rainfall of 234.9 mm, and Fujairah Airport with (153 mm), between the 25 July and 28 July 2022, according to reports on [72] The Gulf Today and The National News [73], respectively.Because of the unusually heavy rains and the presence of seven wadis in Fujairah City, namely Wadi Hayl, wadi Saham, wadi Farfar, wadi Ham, wadi Yabsah, wadi Madhab, and Wadi Safad (Figure 1), affecting total of 4225 people and were evacuated with the help of 1638 personnel who got affected by the flooding that occurred within these wadis and also water that was spilling over the southern side of the Wadi Ham Dam, which is inside the Fujairah city (Figure 5).Approximately 870 individuals were saved, and another 3897 people were given shelter [72] (Gulf Today, 2022).The world's third-largest fuel bunker canter, Fujairah Port, was also affected by widespread flooding [74].The Northern part of UAE, which includes the study area, has recently seen multiple flash flooding incidents.Lately, the Eastern parts of UAE, Ras Al Khaimah (200 mm), Masafi (209.7 mm), and particularly Fujairah Port (inside the study area) recorded the highest rainfall of 234.9 mm, and Fujairah Airport with (153 mm), between the 25 July and 28 July 2022, according to reports on [72] The Gulf Today and The National News [73], respectively.Because of the unusually heavy rains and the presence of seven wadis in Fujairah City, namely Wadi Hayl, wadi Saham, wadi Farfar, wadi Ham, wadi Yabsah, wadi Madhab, and Wadi Safad (Figure 1), affecting total of 4225 people and were evacuated with the help of 1638 personnel who got affected by the flooding that occurred within these wadis and also water that was spilling over the southern side of the Wadi Ham Dam, which is inside the Fujairah city (Figure 5).Approximately 870 individuals were saved, and another 3897 people were given shelter [72] (Gulf Today, 2022).The world's thirdlargest fuel bunker canter, Fujairah Port, was also affected by widespread flooding [74].
Similarly, to this, the floods had a significant negative impact on residential areas, agriculture/plantations, numerous automobiles, hospitals, schools, and electrical lines [75].Since the majority of Fujairah City's key districts were affected, it is crucial to investigate the specific causes of these significant losses in addition to the high rainfall.This work has been done to identify flashflood-sensitive zones in Fujairah City while considering the seriousness of the problem.Similarly, to this, the floods had a significant negative impact on residential areas, agriculture/plantations, numerous automobiles, hospitals, schools, and electrical lines [75].Since the majority of Fujairah City's key districts were affected, it is crucial to investigate the specific causes of these significant losses in addition to the high rainfall.This work has been done to identify flashflood-sensitive zones in Fujairah City while considering the seriousness of the problem.

Materials and Methods
The delineation of LULC features from the remote sensing satellite image Sentinel-2, 2023, which offers a revisit time of 10 days and a spatial resolution of 20 m and is retrieved from the Earth Resource Observation System, was the first of the eight thematic layers needed for this study.The ArcGIS Spatial Analyst module created other resource maps, such as drainage density, elevation, and slope, using SRTM DEM data.The additional thematic maps, such as a comprehensive geomorphology layer, geology, and soil layers, were created using Sentinel-2 images and referred to other works.The CHRS RainSphere website was utilized to gather rainfall data for the research area during the previous 22 years, which was then used to create a GIS layer for our analysis.
The overall methodology used for this study involves both spatial and non-spatial data collection.The spatial data are recorded in the database as several layers in digital form and include maps of drainage density, elevation, slope, geology, geomorphology, LULC, soil, and rainfall.All these layer integrations, queries, analyses, etc., are carried out in a GIS context.As a result, the new maps are accurately created by simply merging these layers and altering them to assess correlations between the selected features in the various layers under consideration.
This research utilized satellite images from the Earth Resource Observation system, specifically Landsat and Sentinel-2 images (Table 1).Landsat images from 1990, 2000, 2010, and Sentinel 2 for 2023 shed light on how the urban sprawl changed in Fujairah City over the years.Bands used in Landsat 7 and Landsat 5 are Band 4 Near-Infrared (0.77-0.90µm),Band 3 Red (0.63-0.69 µm), and Band 2 Green (0.52-0.60 µm) are used.For Sentinel-2, the bands used are Band 2 (Blue: 490 nm), Band 3 (Green: 560 nm) and Band 4 (665 nm).The land use/Land cover features in the study area have been interpreted and traced through onscreen digitization using level III standards of widely used National Remote Sensing Center (NRSC) classification are extracted to the extent discernible from these relatively high-resolution satellite images.All the Sentinel-2 images for the year 2023 were precisely geo-referenced, enhanced and smoothly mosaicked into a single image covering the Fujairah City area.The image mosaic is then subsequently subset with the study area layer.The weighted overlay analysis combines data from several data categories.It applies analytical, statistical measurement, and other processes to the GIS data sets to turn the data into information applicable to a particular application.Using appropriate choice criteria and gradually layering one parameter over another, it is possible to integrate different themed maps.This operation entails computing regions, conducting logical operations, and superimposing several thematic maps.Themes from several satellite images, SRTM data, and supplementary data sets were translated into a raster format.Using ground control points, these raster images were painstakingly geo-rectified before being digitized on-screen with ArcGIS 10.4.To get better results from overlay analysis, these vectorized themes were placed in a GIS environment with uniform projection coordinates.Flood vulnerability maps were created based on each parameter's ranking and weights applied in overlay analysis [76].Table 1 lists each layer's phenomenon, requirement, and source information.Final classifications include high, high, medium, low, and very low-risk areas for flash floods.

Parameters Responsible for Flash Floods
The result covers the creation of several resource input maps and the assessment of potential flood-vulnerable areas.To comprehend the flood dynamics of the research area, it is necessary to evaluate rainfall, DEM, and its derivatives, including elevation, slope, drainage density, LULC, geology, geomorphology, and soil.

Rainfall
The relationship between rainfall and flood occurrences in a region has been established by a significant body of prior literature [36, [77][78][79][80][81].The exact degree to which an increase in rainfall will result in flooding cannot be predicted [82].Instead, it is possible to assert that rainfall is the primary cause of floods in all environmental contexts [83].Numerous studies worldwide have chosen rainfall as one of the key influencing factors for mapping the risk of flash floods [14,[84][85][86].Rainfall in the study area ranges from 80 to 325 mm, with an average of 160 mm [87].It is important to note that the rainiest months in this region are Oct-Apr (Figure 6) (CHRS, Rainsphere).CHRS Rainsphere is an integrated system for global satellite precipitation data and information developed by the center for Hydrometeorology and Remote Sensing at the University of Colorado, Irvine.From 2000 through 2022, the Fujairah City area's annual and monthly data is accessed from the website.When the annual data was closely examined (Figure 7), it was found that in the total 22 years, 14 of the years had an average rainfall of more than 100 mm and above, which is consistent with the flooding data given by [32] until 2018 and later also observed in 2019, 2020, and 2022.To create the rainfall isohyet map with the aid of ArcGIS software, the above rainfall data from the years 2000 to 2022 was used (Figure 8).The study area's 298 km 2 receives between 80 and 140 mm of rainfall, according to the rainfall isohyet map.196 km 2 of the study area will receive rainfall between 140 and 160 mm, with the remaining 65 km 2 to the west of Fujairah City receiving more than 160 mm.The result covers the creation of several resource input maps and the assessment of potential flood-vulnerable areas.To comprehend the flood dynamics of the research area, it is necessary to evaluate rainfall, DEM, and its derivatives, including elevation, slope, drainage density, LULC, geology, geomorphology, and soil.

Rainfall
The relationship between rainfall and flood occurrences in a region has been established by a significant body of prior literature [36, [77][78][79][80][81].The exact degree to which an increase in rainfall will result in flooding cannot be predicted [82].Instead, it is possible to assert that rainfall is the primary cause of floods in all environmental contexts [83].Numerous studies worldwide have chosen rainfall as one of the key influencing factors for mapping the risk of flash floods [14,[84][85][86].Rainfall in the study area ranges from 80 to 325 mm, with an average of 160 mm [87].It is important to note that the rainiest months in this region are Oct-Apr (Figure 6) (CHRS, Rainsphere).CHRS Rainsphere is an integrated system for global satellite precipitation data and information developed by the center for Hydrometeorology and Remote Sensing at the University of Colorado, Irvine.From 2000 through 2022, the Fujairah City area's annual and monthly data is accessed from the website.When the annual data was closely examined (Figure 7), it was found that in the total 22 years, 14 of the years had an average rainfall of more than 100 mm and above, which is consistent with the flooding data given by [32] until 2018 and later also observed in 2019, 2020, and 2022.To create the rainfall isohyet map with the aid of ArcGIS software, the above rainfall data from the years 2000 to 2022 was used (Figure 8).The study area's 298 km 2 receives between 80 and 140 mm of rainfall, according to the rainfall isohyet map.196 km 2 of the study area will receive rainfall between 140 and 160 mm, with the remaining 65 km 2 to the west of Fujairah City receiving more than 160 mm.

Elevation
The classification is carried out using natural breaking in ArcGIS, and the elevation map is created using SRTM DEM of 30 m spatial resolution.The DEM and its derivatives are crucial in determining which regions are at risk of flooding.The research area's elevation and profile graph were produced from SRTM data and are displayed in Figure 9. Experts say elevation is the main factor in a region's ability to regulate floods [88][89][90].Flat lowland places may flood more quickly than higher altitudes because water continuously flows from higher elevations to lower ones [91,92].Most of the study area's built-up regions are lower than 50 m in elevation, rendering them more susceptible to flash flooding.In the study region, the elevation varies from 0 to 1100 m.Given that increased elevation decreases flash flooding risk, the entire range of elevation is divided into five rank classes ranging from 1 to 5. The ranks are assigned to various sections of the research region based on elevation for additional GIS analysis.
Water 2023, 15, x FOR PEER REVIEW 11 of 31

Elevation
The classification is carried out using natural breaking in ArcGIS, and the elevation map is created using SRTM DEM of 30 m spatial resolution.The DEM and its derivatives are crucial in determining which regions are at risk of flooding.The research area's elevation and profile graph were produced from SRTM data and are displayed in Figure 9. Experts say elevation is the main factor in a region's ability to regulate floods [88][89][90].Flat lowland places may flood more quickly than higher altitudes because water continuously flows from higher elevations to lower ones [91,92].Most of the study area's built-up regions are lower than 50 m in elevation, rendering them more susceptible to flash flooding.In the study region, the elevation varies from 0 to 1100 m.Given that increased elevation decreases flash flooding risk, the entire range of elevation is divided into five rank classes ranging from 1 to 5. The ranks are assigned to various sections of the research region based on elevation for additional GIS analysis.

Slope
The slope of the research area indicates a crucial role in controlling surface discharge in hydrological assessment studies.The significance of this topographic feature has been noted by several researchers [84,88,90,93].The slope of an area and the surface flow velocity have a significant positive link [91,94].In addition, gradient influences infiltration to some extent.As the gradient rises, the surface runoff rises noticeably as well, which causes the infiltration to fall [91].Due to the large amount of water that becomes immobile and generates a severe flood situation, places with a sudden fall in slope have a higher

Slope
The slope of the research area indicates a crucial role in controlling surface discharge in hydrological assessment studies.The significance of this topographic feature has been noted by several researchers [84,88,90,93].The slope of an area and the surface flow velocity have a significant positive link [91,94].In addition, gradient influences infiltration to some extent.As the gradient rises, the surface runoff rises noticeably as well, which causes the infiltration to fall [91].Due to the large amount of water that becomes immobile and generates a severe flood situation, places with a sudden fall in slope have a higher likelihood of flooding [88,95,96].According to [97], a greater slope's size may hasten precipitation-related runoff.With the help of the 3D Analyst module in ArcGIS, the slope map is instantly generated from the SRTM DEM-the values of the slope range from 5% to 20%.The entire slope is divided into five classes, with the understanding that the lower the slope, which is less than 5%, the higher the vulnerability of the area, as shown in Figure 10, the higher the slope, more than <20% values lower the vulnerability wrt to flooding.Based on this, the ranks are assigned to all the areas in the study region.
Water 2023, 15, x FOR PEER REVIEW 12 of 31 likelihood of flooding [88,95,96].According to [97], a greater slope's size may hasten precipitation-related runoff.With the help of the 3D Analyst module in ArcGIS, the slope map is instantly generated from the SRTM DEM-the values of the slope range from 5% to 20%.The entire slope is divided into five classes, with the understanding that the lower the slope, which is less than 5%, the higher the vulnerability of the area, as shown in Figure 10, the higher the slope, more than <20% values lower the vulnerability wrt to flooding.Based on this, the ranks are assigned to all the areas in the study region.

Drainage Density
A key concept in hydrological analysis is drainage density, determined as the total drainage length to the basin area.The drainage density is influenced by the permeability, the capacity of surface materials to erode, vegetation, slope, and time.Overland flow caused by inadequate drainage might choke drainage and water channels [98].Equation 1 is used to calculate the drainage density: where D is the water drainage density, L is the drainage channel's overall length, and A is the water area.Higher drainage density values are significantly correlated with a lower likelihood of floods in the region since it denotes greater surface runoff, while lower drainage density values resemble higher vulnerability to flash floods.The prepared drainage

Drainage Density
A key concept in hydrological analysis is drainage density, determined as the total drainage length to the basin area.The drainage density is influenced by the permeability, the capacity of surface materials to erode, vegetation, slope, and time.Overland flow caused by inadequate drainage might choke drainage and water channels [98].Equation 1 is used to calculate the drainage density: where D is the water drainage density, L is the drainage channel's overall length, and A is the water area.Higher drainage density values are significantly correlated with a lower likelihood of floods in the region since it denotes greater surface runoff, while lower drainage density values resemble higher vulnerability to flash floods.The prepared drainage density map is shown in Figure 11 using the line density command in the ArcGIS Hydrology module.The drainage density map of the study area is generated from the drainage network layer.According to [99], regions with higher drainage densities produce more surface runoff than regions with lower drainage densities.Accordingly, the drainage density, a crucial element for creating runoff [100,101], may depend on the expansion of flood risk.
Water 2023, 15, x FOR PEER REVIEW 13 of 31 density map is shown in Figure 11 using the line density command in the ArcGIS Hydrology module.The drainage density map of the study area is generated from the drainage network layer.According to [99], regions with higher drainage densities produce more surface runoff than regions with lower drainage densities.Accordingly, the drainage density, a crucial element for creating runoff [100,101], may depend on the expansion of flood risk.

Land Use/Land Cover
The structure of land use, the distribution of land cover, and its temporal evolution can all have a significant impact on an area's flood frequency [102,103].The land use of an area has a significant impact on hydrological responses at different times, according to [103].Therefore, ref. [104] showed that changes in land use can increase a region's likelihood of flooding.This paper creates a detailed LULC map utilizing on-screen digitization of Sentinel-2 data pertaining to 2023, as shown in Figure 12.There were mainly ten categories were identified on the LULC map, and their areas are represented in Table 2, namely Builtup-Residential, Builtup-Commercial, Builtup-Residential/Plantation, Builtup-Under development, Builtup-Mining, Barren Lands, Builtup-Oil storage areas, Airport, Fujairah Port, Beaches and Hajar Mountains.The Hajar Mountains occupy around 403 km 2 , while the residential and plantation areas comprise 52 km 2 , and mining areas include 14 km 2 .Fujairah port has a total area of 11.7 km 2 and an oil storage area of another 5.7 km 2 .In all these areas, Built-up residential and plantation areas, Fujairah Port, Commercial areas, airports, oil storage areas, and beaches are given a high-risk value of 5.

Land Use/Land Cover
The structure of land use, the distribution of land cover, and its temporal evolution can all have a significant impact on an area's flood frequency [102,103].The land use of an area has a significant impact on hydrological responses at different times, according to [103].Therefore, ref. [104] showed that changes in land use can increase a region's likelihood of flooding.This paper creates a detailed LULC map utilizing on-screen digitization of Sentinel-2 data pertaining to 2023, as shown in Figure 12.There were mainly ten categories were identified on the LULC map, and their areas are represented in Table 2, namely Builtup-Residential, Builtup-Commercial, Builtup-Residential/Plantation, Builtup-Under development, Builtup-Mining, Barren Lands, Builtup-Oil storage areas, Airport, Fujairah Port, Beaches and Hajar Mountains.The Hajar Mountains occupy around 403 km 2 , while the residential and plantation areas comprise 52 km 2 , and mining areas include 14 km 2 .Fujairah port has a total area of 11.7 km 2 and an oil storage area of another 5.7 km 2 .In all these areas, Built-up residential and plantation areas, Fujairah Port, Commercial areas, airports, oil storage areas, and beaches are given a high-risk value of 5.In contrast, Underdevelopment areas, plantation areas, under development areas are given a risk value of 4, mining areas into 3, barren lands 2, and mountains 1, as shown in Table 3.
In contrast, Under-development areas, plantation areas, under development areas are given a risk value of 4, mining areas into 3, barren lands 2, and mountains 1, as shown in Table 3.    Due to geological variance, a region's temporal flood has a high potential to change the wadi profile [105], and it can be regarded as a significant factor since it increases the severity of a flood occurrence [106,107].Additionally, a region's geology can provide important details about the frequency of paleo-flood occurrences [108].The infiltration rate and a rock's permeability are strongly correlated.To prevent floods, impermeable rocks encourage surface drainage.The study area's geology map was created based on past research by [109,110], and it is split into four primary geological types: Igneous and metamorphic rocks from the Jurassic to the Cretaceous Period; sedimentary rocks from the Permian to the Cretaceous Period; alluvium from the Quaternary Period in Wadis, plains, and sands; and Quaternary Coastal Deposits (Figure 13).Finally, larger infiltration rates will result from a geological formation with higher permeability, whereas higher surface runoff rates will result from an impermeable layer.
Water 2023, 15, x FOR PEER REVIEW 16 of 31 4.1.6.Geology Due to geological variance, a region's temporal flood has a high potential to change the wadi profile [105], and it can be regarded as a significant factor since it increases the severity of a flood occurrence [106,107].Additionally, a region's geology can provide important details about the frequency of paleo-flood occurrences [108].The infiltration rate and a rock's permeability are strongly correlated.To prevent floods, impermeable rocks encourage surface drainage.The study area's geology map was created based on past research by [109,110], and it is split into four primary geological types: Igneous and metamorphic rocks from the Jurassic to the Cretaceous Period; sedimentary rocks from the Permian to the Cretaceous Period; alluvium from the Quaternary Period in Wadis, plains, and sands; and Quaternary Coastal Deposits (Figure 13).Finally, larger infiltration rates will result from a geological formation with higher permeability, whereas higher surface runoff rates will result from an impermeable layer.2014), the interplay of wind and water is a major element in the geomorphology of arid regions and has a significant impact on long-term landscape evolution in these locations.Additionally, fine silt is transported to alluvial areas by rain and floods, where it can be altered by aeolian processes [111].Like how dust and sand are transported by wind, they can be carried by water in channels or as a surface wash in alluvial and sloped environments.
Therefore, one of the most crucial factors in assessing flash flood susceptibility is geomorphological analysis.It is essential to the management of water resources and aids in a variety of planning and development tasks, such as managing floodplains, building recharge structures, and rerouting stormwater, among others.In the research region, there are primarily five geomorphic features detailed in Figure 14 that was chosen as a reference from [109].Wadis, Flood Plains, and Alluvial Plains are examples of fluvial landforms.Along with beaches, Coastal Plains comprise the other major landform in the study region.2014), the interplay of wind and water is a major element in the geomorphology of arid regions and has a significant impact on long-term landscape evolution in these locations.Additionally, fine silt is transported to alluvial areas by rain and floods, where it can be altered by aeolian processes [111].Like how dust and sand are transported by wind, they can be carried by water in channels or as a surface wash in alluvial and sloped environments.
Therefore, one of the most crucial factors in assessing flash flood susceptibility is geomorphological analysis.It is essential to the management of water resources and aids in a variety of planning and development tasks, such as managing floodplains, building recharge structures, and rerouting stormwater, among others.In the research region, there are primarily five geomorphic features detailed in Figure 14 that was chosen as a reference from [109].Wadis, Flood Plains, and Alluvial Plains are examples of fluvial landforms.Along with beaches, Coastal Plains comprise the other major landform in the study region.

Soil
A natural resource that directly affects floods is soil because it regulates how much water can permeate the soil and is the main element of the hydrological cycle [113], as a result, how much water flows [114].In dry locations with severe water scarcity, soil information and maps are crucial for decision-making [115].They provide a wealth of information on its environmental applications and potential concerns.The ability of soils to infiltrate water and behave as sponges will be significantly influenced by their structure and infiltration capacity.Different types of soils hold and infiltrate water differently, impacting flood susceptibility [116].Reduced soil infiltration capacity leads to increased surface runoff, which raises the risk of flooding.Flooding can occur when water is delivered at a pace that exceeds the soil's capacity for infiltration [117].This is because the water rushes down the slope at a rapid rate.The created soil map from [115] is depicted in Figure 15.

Evaluation of Probable Flash Flood Vulnerable Zones
In assessing the risk of flash flooding, GIS is increasingly important.A spatial database is created using ArcGIS 10.4.The study of raster overlays is crucial in assembling the In coastal regions, aquisalids are extremely salinity-rich and poorly drained soils.These soils are located toward the southwest of the research region and encompass an area of 0.362 km 2 .In addition to having a high concentration of salts, some of these soils also have a high concentration of gypsum.Salt concentrations are intense towards the surface due to capillary rise and water evaporation.The extreme salinity of these soils causes them to be physiologically dry despite groundwater, which only allows salt-tolerant plant species to grow there.
Haplocalcids are a type of soil where the upper layer of the subsoil contains calcium carbonate.These soils cover 26.33 km 2 in the research area, with the majority of them situated in the center to the northwest region.These soil types can readily absorb surface water since they are typically sandy or loamy.12% of the city of Fujairah is covered by these types of soils.
Most torriorthents contain more than 35% by volume of gravel.They are found in wadis within mountain valleys, alluvial fans, and plains next to mountains.Other Torriorthents are found on wadis or alluvial plains farther away from the mountains.They are usually sandy and have little to no gravel, but within 100 cm, there may be one or more strata with a loamy texture.The term "rock outcrops" refers to regions of rock outcrop surrounded by soils rather than the vast amounts of rock outcrop that make up the mountains.It comprises rounded hills with low relief and steep, rocky hills in some places.The 3.643 km 2 area of this map unit is covered by various outcrops made of sandstone, conglomerate, limestone, gypsum, ophiolite, and gabbro, among other rock types.

Evaluation of Probable Flash Flood Vulnerable Zones
In assessing the risk of flash flooding, GIS is increasingly important.A spatial database is created using ArcGIS 10.4.The study of raster overlays is crucial in assembling the data needed to portray the phenomena.One of the simplest ways to join distinct layers is by using "Yes" or "No" rules from Boolean logic.Most Boolean logical-based overlay processes used in GIS do not consider the fact that variables may not be equally important and that threshold value determinations are sometimes arbitrary.The mathematical Overlay approach was therefore used to quantify the analysis's parameters.The result is a raster layer with a value assigned to each grid cell due to the productive overlay procedure.
By combining the spatial data of rainfall, drainage density, elevation, slope, LULC, geology, geomorphology, and soil, a map of flood risk zones has been created.The parameter's weight value is displayed as a percentage between 0% and 100%.The list of the intended parameters, their weights, and their ranks are shown in Table 3.The class values are ranked from 1 to 5 per scientific norms and presumptions after calculating the criteria value ranges [118].Rankings were given from 1 to 5, with 5 representing the most significant element and 1 representing the least important.The proper weights were assigned based on the features and characteristics of the strata shown in Table 3. Figure 16 illustrates the creation of the flash flood vulnerable map for the study area using information from Table 3.The very high, high, moderate, low, and very low vulnerable zones, which account for 11.7%, 16.6%, 1.9%, 25.5%, and 44.3% of the research area, respectively, are shown on the flood-vulnerable map.Because mountains with heights greater than 80 m above mean sea level encompass most of the study area, 71.7% of it falls under moderate to very low vulnerable zones.The remaining 28.3% comprises high and very highly vulnerable areas.This includes the heavily inhabited, low-lying districts overlooking the Gulf of Oman in Fujairah City, which has encroached into topographically delicate territory prone to flash floods.Additionally, as seen in Figure 3, the steady increase of built-up areas in the Fujairah City region expands the area of impermeable infrastructure, which reduces infiltration and increases runoff in the event of significant rainfall over a brief period.

Discussion
The results of this study concur with those from previous studies employing machine learning [4] and weighted analytical techniques [32].They determined that among the chosen factors, elevation and slope carried the most weight.Flash floods were mostly caused by elevation, with slope and rainfall coming in second and third.Another study from Ethiopia, by [126], determined that slope is the main reason for flash floods.Additionally, ref. [51] stated that the primary characteristics of their study include rainfall, DD, elevation, and slope.The findings of previous research [127] and ref. [98] demonstrated the critical role that elevation and slope play in influencing the movement of the overflow route.Also [32] included LULC in their analysis.The current analysis emphasizes assigning high weightage for rainfall, DD, elevation, slope, and LULC while considering all the previous studies.
To develop flash flood risk zones, weighted sum overlay analysis fusion methodologies were used.These can forecast flood risk areas thanks to the many different classification criteria.A flash flood vulnerability map was produced by incorporating eight conditional parameters through GIS-based weighted overlay analysis, normalization, and expert opinion technique, as discussed in previous research [128][129][130].A larger weight indicates high flooding vulnerability.Lower weight levels, on the other hand, suggest that flooding is less likely to happen.The outcome map was separated into five zones using the natural break method: very high, high, moderate, low, and very low (Figure 16), covering areas of 55 km 2 , 78 km 2 , 9.3 km 2 , 120 km 2 , 207 km 2 (Figure 16).Fujairah City has been identified as one of the locations with the highest risk of flooding.This results from the Fujairah city's quick development, encroaching on topographically delicate regions vulnerable to flash floods.In addition, building and road construction in urban areas expands the area of impervious infrastructure, which reduces infiltration and increases runoff, leading to flash floods in the event of heavy rain that falls over a short time.The much more significant causes of flood vulnerability in these areas are human activities that result in considerable changes in the geometry of the watershed, such as elevation changes in the topography, existing drainage modifications, and a rise in the number of Nearly 90% of the images from earlier flood events taken on the field, discovered in areas with highly vulnerable zones for flooding (Figure 16), were used to confirm the accuracy of the flash flood vulnerability map along with the reference from [4,32].This shows that the GIS model output and the earlier flash flood occurrences had a significant degree of consistency.The map of flash flood vulnerable zones is a useful tool for planning flood defences and safeguarding the safety of persons residing in extremely high and very highly vulnerable areas.For instance, since it was discovered that more vulnerable areas are located along the low coastal plains, which regrettably are areas of high population density, preventive measures, such as the incorporation of planning regulations, the avoidance of development near highly vulnerable areas, the construction of embankments, raising public awareness, and the establishment of early warning systems by the installation of flow meters with alarms, can be taken into consideration.By adding additional storage dams, raising the heights of the current ones, and clearing the silt from them, more water can be saved, groundwater can be recharged, and people can be protected from flash floods [119,120].To use the estimated 150 million m 3 per year from 15 major catchment areas in the UAE, the Ministry of Environment and Water built 113 recharge and storage dams [121].To lessen the impact of flooding, an early warning system for flash floods is essential.Additionally, remote sensing data might supplement rain gauge data for real-time precipitation estimation [122][123][124][125].This would allow researchers to determine whether a rainstorm event will suddenly cause low-lying areas to flood.

Discussion
The results of this study concur with those from previous studies employing machine learning [4] and weighted analytical techniques [32].They determined that among the chosen factors, elevation and slope carried the most weight.Flash floods were mostly caused by elevation, with slope and rainfall coming in second and third.Another study from Ethiopia, by [126], determined that slope is the main reason for flash floods.Additionally, ref. [51] stated that the primary characteristics of their study include rainfall, DD, elevation, and slope.The findings of previous research [127] and ref. [98] demonstrated the critical role that elevation and slope play in influencing the movement of the overflow route.Also [32] included LULC in their analysis.The current analysis emphasizes assigning high weightage for rainfall, DD, elevation, slope, and LULC while considering all the previous studies.
To develop flash flood risk zones, weighted sum overlay analysis fusion methodologies were used.These can forecast flood risk areas thanks to the many different classification criteria.A flash flood vulnerability map was produced by incorporating eight conditional parameters through GIS-based weighted overlay analysis, normalization, and expert opinion technique, as discussed in previous research [128][129][130].A larger weight indicates high flooding vulnerability.Lower weight levels, on the other hand, suggest that flooding is less likely to happen.The outcome map was separated into five zones using the natural break method: very high, high, moderate, low, and very low (Figure 16), covering areas of 55 km 2 , 78 km 2 , 9.3 km 2 , 120 km 2 , 207 km 2 (Figure 16).Fujairah City has been identified as one of the locations with the highest risk of flooding.This results from the Fujairah city's quick development, encroaching on topographically delicate regions vulnerable to flash floods.In addition, building and road construction in urban areas expands the area of impervious infrastructure, which reduces infiltration and increases runoff, leading to flash floods in the event of heavy rain that falls over a short time.The much more significant causes of flood vulnerability in these areas are human activities that result in considerable changes in the geometry of the watershed, such as elevation changes in the topography, existing drainage modifications, and a rise in the number of impervious surfaces in the City area (Figure 3).All of these factors have raised the risk of floods and flooding of essential infrastructure, which increases the chance of fatalities and financial loss [2].Despite the high-risk area, change detection maps showed the significant changes that have occurred in urban and vegetation areas since 1990 (Figure LULC alterations).2010 to 2023 saw a significant improvement in Fujairah City's infrastructure.
In general, flood risk maps are helpful for local citizens, decision-makers, and competent authorities.They can help select the best flood risk reduction measures for watersheds [131][132][133].It is simpler to locate the danger areas with flood risk mapping.Additionally, there will be consistency in deciding how and where to reduce urban expansion in the risk zones with a methodical technique like weighted overlay analysis.The growth of urban areas near floodplain areas and the presence of many facilities may enhance the flood intensity.The findings of this study demonstrated that urbanization has an impact on hydrological processes as well, reducing groundwater infiltration and increasing runoff.

Hazard Management, Field Observations and Recommendations
We learnt that the Wadi Ham South Dam experienced water overflowing during the floods of July 2022 (Figure 5), which caused the neighboring areas to flood.We have thus examined the wadis that are to blame for this flood in this regard.Two wadis, wadi Farfar and Wadi Saham, where Wadi Saham joins with Wadi Farfar and later both the wadis empties into the Wadi Ham main dam, are to blame for the increased flood water accumulation in the Wadi Ham south dam.Wadi Saham has a width of 67 m before joining Wadi Farfar, and Wadi Farfar has 236 m width before reaching the Wadi Ham main Dam.
After thorough field visits, these two wadis have no breaker dams or artificial lakes, so they are the source of the additional flood water.Furthermore, Wadi Saham's bed slope (Figure 17c) is quite steep, causing the water to surge into Wadi Fafar before rejoining the Wadi Ham main dam.The field photos were collected during the most recent floods in July 2022 (Figure 5).The Wadi Safad and Wadi Madhab both have steep slopes (Figure 17e,f) that will cause the flow strength to grow and flood the downstream areas.Due to the abrupt power of the water from upstream that defines the steep slopes in the wadi bed, there were destroyed roads and culverts downstream of Wadi Safad (Figure 18).so they are the source of the additional flood water.Furthermore, Wadi Saham's bed slope (Figure 17c) is quite steep, causing the water to surge into Wadi Fafar before rejoining the Wadi Ham main dam.The field photos were collected during the most recent floods in July 2022 (Figure 5).The Wadi Safad and Wadi Madhab both have steep slopes (Figure 17e,f) that will cause the flow strength to grow and flood the downstream areas.Due to the abrupt power of the water from upstream that defines the steep slopes in the wadi bed, there were destroyed roads and culverts downstream of Wadi Safad (Figure 18).Monitoring flood-prone areas can reduce the likelihood of flooding [134], and flood mitigation strategies can be divided into non-structural and structural approaches [134,135].Non-structural measures do not require engineering, such as boosting preparation through early warnings, controlling land use and development, planning and man- Monitoring flood-prone areas can reduce the likelihood of flooding [134], and flood mitigation strategies can be divided into non-structural and structural approaches [134,135].Non-structural measures do not require engineering, such as boosting preparation through early warnings, controlling land use and development, planning and managing flood control reservoirs, and more [135,136].In-depth ecosystem-specific methods, including restoring natural conditions or conventional measures like dams and levees can be used as structural defence tactics [135].In addition, structural improvements may be crucial for controlling dangerous floods and managing water [137,138].
According to [134,139], successful flood mitigation techniques should consider the following factors: (1) a proper flood control implementation strategy; (2) a suitable site for facility installation; (3) a suitable facility size; and (4) efficient facility maintenance and operation.Most of the roads and other infrastructure in Fujairah City have been built across wadis that encircle the main city.Although complete flood protection is impractical, the risk of a flood disaster could be decreased by (1) reducing exposure by stopping or shifting development activities in floodplains and other high-hazard areas, (2) reducing vulnerability by establishing resilient infrastructure standards and designs, and (3) reducing the hazard itself, in some cases, by building flood mitigation measures.

Essential Physical Structural Procedures
Structured mitigation strategies can be divided into scattered and concentrated strategies according to the spatial scale.Distributed structural measures for flood mitigation have been considered in several previous research [140][141][142][143][144][145].According to [141,145], the major objective of dispersed structures is to ease the flow peak and store extra floodwaters upstream of wadis to lessen the discharge in downstream areas.Fujairah has implemented several methods to reduce flash floods, including integrating retention and breaker dams and man-made lakes, resulting in water management and flood mitigation.Following a thorough analysis of all the wadis in Fujairah City by researchers, it was discovered that 15 breaker dams have 4 m in height built on three Wadis, in addition to 2 main dams of 12 m each built on the wadi Ham and wadi Safad (Figure 1).Also, there should be one breaker dam built each on the Wadi Saham and Wadi Farfar.Therefore, to control flash floods and water harvesting, which in turn helps to improve the groundwater aquifers of Fujairah City, some breaker dams and artificial lakes should be proposed based on the expected volume of flood water, risk and hazard degree, and their return periods.

Necessary Solutions without Any Physical Structures
By altering land use, issuing early warnings, and lowering flood susceptibility and exposure, non-structural flood control strategies have been widely used to lower the flow peak [136,[146][147][148]. Additionally, socioeconomic developments and governmental structures impact how effective non-structural flood control techniques are [149].On the other hand, non-structural control measures offer adaptable flood mitigation strategies for considering changes in Wadi systems, climate change, and socioeconomic effects, which might impede the establishment of a sustainable environment [150].

Conclusions
Numerous flash floods have affected Fujairah City and its residents, some of which have been quite catastrophic and have left lasting harm in their wake, as was shown by the most recent flooding on 28 July 2022.After carefully examining the various geomorphic features of the research region, it became apparent that seven wadis flowed into Fujairah City and that roughly 17 dams, including two significant dams and additional breaker dams, had been built to hold water.To analyze and manage flash flood hazards, it is crucial to create a flash flood hazard map.After normalization and weighting by implementing expert opinions, several parameters, mostly derived from remote sensing data, such as slope, elevation, land use, land cover, geomorphology, geology, soil, rainfall, and drainage density, were combined to map flood-vulnerable areas.The information made it possible to assess the impact of the floods on Fujairah City and identify the areas that were most at risk.The Fujairah City Flash Flood susceptible zones model identified very high susceptible areas (11.72%), highly vulnerable areas (16.63%), moderate (1.9%), low (25.58%), and very low (44.13%)vulnerability.
Because it is largely steep terrain, the western section of the study area is less susceptible to flash floods.Due to the flat coastal plain and impermeable regions, the eastern portion, where the metropolitan areas are situated, is extremely vulnerable to flooding.The model findings were verified and compared to the flood that occurred on 28 July 2022, and they nearly matched the vulnerability map's final results.As approximately 27% of the study region, which includes mining sites, underdevelopment areas, residential areas, and other built-up areas, is subject to significant hazards due to floods, the research's findings can help to lessen the risks that flood catastrophes offer to the local people.The weighted overlay method and GIS analysis used in this study to create the flood vulnerable map provide municipality officials with crucial information that they can use to explain the risks of flooding and develop emergency preparedness and mitigation strategies for various target groups, particularly for residents of high-risk neighborhoods.
Using maps and satellite images procured at distinct points in time and at different scales can lead to attribute and positional mistakes, leading to technical limits in any GISrelated procedures.As a result of generalization, there can be probable inaccuracies in the classification of land uses.For instance, even though they are categorized as built-up residential areas under the law of the majority, built-up regions also include many green spaces.The Shuttle Radar Topography Mission (SRTM) is the foundation for the elevation data.One-arc second data (30 m) is the resolution of the source data cells.Since no other topographical data were available, the SRTM data, which is typically not appropriate for flood modeling [151], was used in this work.
Furthermore, it is inaccurate to categorize elevation based just on bare ground.If an area has a good drainage system, especially in metropolitan areas, it may not be true that low ground has a high likelihood of flooding.The growth of new highways and urban areas, as well as climate change, will cause changes to the flash flood vulnerability map over time [152].As a result, the present flood vulnerability map created here should only be used as a basic guide.It should not be utilized to make long-term decisions.

Figure 1 .
Figure 1.Location map of the study area showing the important areas in Fujairah City.

Figure 1 .
Figure 1.Location map of the study area showing the important areas in Fujairah City.

Figure 4 .
Figure 4. Urbanization trends in the study area.

Figure 5 .
Figure 5. Water flowed over the Wadi Ham South Dam during the floods of July 2022.

Figure 4 .
Figure 4. Urbanization trends in the study area.

Figure 4 .
Figure 4. Urbanization trends in the study area.

Figure 5 .
Figure 5. Water flowed over the Wadi Ham South Dam during the floods of July 2022.Figure 5. Water flowed over the Wadi Ham South Dam during the floods of July 2022.

Figure 5 .
Figure 5. Water flowed over the Wadi Ham South Dam during the floods of July 2022.Figure 5. Water flowed over the Wadi Ham South Dam during the floods of July 2022.

Figure 8 .
Figure 8.Average Rainfall map of Fujairah City.

Figure 8 .
Figure 8.Average Rainfall map of Fujairah City.Figure 8. Average Rainfall map of Fujairah City.

Figure 8 .
Figure 8.Average Rainfall map of Fujairah City.Figure 8. Average Rainfall map of Fujairah City.

Figure 9 .
Figure 9.The elevation map of Fujairah City.

Figure 9 .
Figure 9.The elevation map of Fujairah City.

Figure 11 .
Figure 11.Drainage density map of Fujairah City.

Figure 11 .
Figure 11.Drainage density map of Fujairah City.

Figure 12 .
Figure 12.Land Use/Land Cover Map of Fujairah City.

Figure 12 .
Figure 12.Land Use/Land Cover Map of Fujairah City.

Figure 13 .
Figure 13.Geology map of Fujairah City.Figure 13.Geology map of Fujairah City.

Figure 13 .
Figure 13.Geology map of Fujairah City.Figure 13.Geology map of Fujairah City.

Figure 14 .
Figure 14.Geomorphology map of Fujairah City.Figure 14. Geomorphology map of Fujairah City.

Figure 14 .
Figure 14.Geomorphology map of Fujairah City.Figure 14. Geomorphology map of Fujairah City.

Figure 15 .
Figure 15.Soil map of Fujairah City.

Figure 16 .
Figure 16.Flash flood vulnerable zones of Fujairah City.

Figure 16 .
Figure 16.Flash flood vulnerable zones of Fujairah City.

Figure 18 .
Figure 18.Showing the eroded culverts and road downstream of Wadi Safad.

Figure 18 .
Figure 18.Showing the eroded culverts and road downstream of Wadi Safad.Before reaching the Wadi Ham main dam, Wadi Ham has a 330 m width, which is claimed to be the widest of all the wadis in the analysis of Wadi bed widths.Its width is roughly 45 m, close to the starting point.The Wadi Safad has a maximum width of 119 m close to the Safad Dam, and as you descend toward the downstream breaker dam near Al Qurayyah, that breadth increases to 280 m.

Table 1 .
Data utilized for various parameters.

Table 2 .
Land use land cover classification of the study area.

Table 2 .
Land use land cover classification of the study area. S.

Table 3 .
Weights, classes, and scores for map layers.