Analysis and Design of Monopile Foundations for Offshore Wind and Tidal Turbine Structures

: This paper aims to design an integrated offshore structure capable of supporting a hybrid assembly of one wind plus two tidal turbines. The monopile has been found to be a suitable foundation type as the most inexpensive solution in water depths of less than 30 m. The Cook Strait in New Zealand is an ideal location for wind and tidal renewable energy sources due to its strong winds and tidal currents. Finite element analysis was performed to determine the displacement of the structure for different types of soils using OPTUM G3. After that, a macro-element model for soil was represented, considering the monopile as a Euler–Bernoulli beam model. The results enable the ﬁnding of optimum dimensions of monopiles with allowable tilt and deﬂection. Based on this, the diameter, thickness, and length of the monopile can be 6, 0.083, and 60 m, respectively. The maximum load occurs in extreme wind load scenarios when wind and waves move in same direction.


Introduction 1.Hybrid Generation from Offshore Renewable Sources
Deployed on floating bodies or along cables, offshore energy harvesters can convert wave, solar, tidal, ocean currents, and other renewable energy sources to stable electrical energy [1].Creating hybrids with wind electricity generation would reduce the currently significant operations and maintenance (O&M) of wind turbines (WT), which is around 10-25% of the total cost of electricity, and a lower transmission cost [2,3].By bringing together two marine renewable technologies with considerable synergies, the combined harnessing of offshore energies creates excellent potential for development.This is corroborated by some recent European Union (EU)-funded projects: MARINA, ORECCA, TROPOS, MERMAID, and H2OCEAN [4].MARINA classifies combined wave-wind systems according to the technology, water depth (shallow, transition, or deep water), or location relative to the shoreline (shoreline, nearshore, offshore).ORECCA analyses the offshore renewable energies (ORE) combined resources in Europe.Looking particularly at Europe's combined wave-wind resource, this can be divided into three main sea basins: the Mediterranean Sea, the North and Baltic Seas, and the Atlantic Ocean.TROPOS is aimed at developing a floating multi-purpose platform system for deep water [4].The MERMAID project seeks to develop concepts for the next generation of offshore activities for multi-use ocean space.It proposes new design concepts for combining offshore activities, such as energy extraction, aquaculture, and platform-related transport at various ocean areas [5].H2OCEAN is developing a wind-wave power open-sea platform for hydrogen generation with support for multiple energy users [6].
The main projects installed in the previous decade (2010-2019) were the 2.3 MW Hywind in Norway in 2009, the 2 MW Principle Power in Portugal in 2011, and the MOE project in Japan with capacities of 100-kW half-scale model in 2012, and 2 MW full scale in 2013 [7].Da et al. (2009) propose a control scheme for a hybrid system.Adjusting the generator's rotation speed can maximize the system's output power under fluctuating wind or tidal currents [8].Li et al. (2017) show the integration of floating wind turbines with a wave energy converter and tidal turbines increases power production by 22-45% [9].Lande et al. (2019) modelled the co-location of a wind turbine with an array of tidal stream turbines in the MeyGen site located in Pentland Firth, UK.It will increase energy yield by around 11% and decrease the levelized cost by 10% [10].Nichita et al. present the "accelerated simulation time" method and its experimental validation.Wind or tidal turbine characteristics are obtained using the simulation approach developed at the GREAH lab and are validated with an actual ocean turbine installed in the Circulating Water Channel at Inha University Ocean Engineering Laboratory, South Korea [11].Phurailatpam et al. [12] present a DC microgrid for rural applications in India using wind turbines (WT) and photovoltaic panels (PV).Azaza et al. give some insight and techno-economic analysis of microgrid deployment in different Swedish regions using PV/WT/DG, a battery bank, and an energy management system to identify the optimal system size and configuration [13].Thakur et al. designed, constructed, and tested a new physical simulator under different operating conditions in a real microgrid environment.The simulator replicates the behaviour of a designed wind turbine.The experiments have also shown that the designed wind turbine can work in harmony with PV power modules and battery storage in response to weather and load variations in an island microgrid environment [14].Wang et al. analysed the stability of a microgrid system containing an offshore wind farm (OWF), an offshore tidal farm (OTF), and a seashore wave farm (SWF) fed to an onshore power grid through a high-voltage direct current (HVDC) link based on a voltage-source converter (VSC) [15].Adetunji et al. proposed an optimized grid-connected microgrid for South Africa using photovoltaic panels (PV) and a supporting lead-acid battery for downtime [16].Kitson et al. present a DC microgrid system, interfacing wind and solar using a power electronic interface with droop functions.A case study site in Nepal is simulated to demonstrate the system's performance to variable generation and loads [17].Oulis Rousis et al. designed an off-grid system in Greece relying on PV, diesel generators, and batteries for energy storage [18].Phurailatpam et al. compared different scenarios of DC microgrids in the Indian context using wind and photovoltaic panels for India's rural and urban power supply [19].Faridnia et al. designed a grid-connected microgrid for a tidal farm near Darwin, in the north of Australia, including tidal power as the main supply, a pumped hydro system (PHS) with 1000 kWh capacity as the long-term storage system, and a micro-turbine (MT) to minimize the operating cost [20].Colombo et al. added Photovoltaic (PV) to power-to-gas (P2G) to reduce emissions [21].

The Integration of Offshore Wind with Tidal Energy
Over the recent decades, offshore wind farms have attracted more investment [22].It is estimated that onshore and offshore wind power will generate more than a third of the total electricity needed in the medium term, becoming the primary generation source by 2050 [23].Compared with onshore wind energy resources, offshore wind fields have many advantages, such as persistent wind, faster-flowing speed, higher uniformity, and longer available time per year, flat sea surface, and low turbulence intensity, which promotes the vigorous development of the offshore wind power industry [24,25].More importantly, installing wind turbines in the ocean can protect the environment [26] and save land resources [27].The vast ocean area provides good conditions for developing large-scale wind farms and turbines [28].The power generation by the identical turbines in the offshore area is 50-100% higher than in the onshore area [29].However, the main issue for investors is capital cost which results in increasing the electricity cost for customers.The most expensive component of an offshore wind turbine is the foundation, accounting for 19% of the capital cost.In addition, foundation installation with 6% of the capital cost is the highest cost compared with other parts [30].However, the cost of electricity using offshore wind is still high [31].As another offshore energy source, installing tidal turbines Water 2022, 14, 3555 3 of 18 has attracted less investment because tidal turbines are exposed to harsh currents.Their lifetime is low, and foundation design is complex in most cases, where the water depth is more than 30 metres [32].However, tidal turbines can produce an enormous amount of electricity, more than four times per square meter of the rotor than wind turbines [33].Integration of both wind and tidal turbines with the same foundation may be a way to reduce the cost of electricity [7] and enable predictable power generation from two different energy sources.
Although New Zealand is surrounded by water and has good potential for offshore energy, it has not yet been used for power generation.In recent years, several reports indicated the annual demand of electricity increases from current demand of 40 TWh to 70 TWh by 2050 [34].Therefore, looking for new sources of harvesting power generation is essential.
This paper describes a preliminary design for an offshore structure capable of supporting a hybrid assembly of one wind plus two tidal turbines, as shown in Figure 1.
The most expensive component of an offshore wind turbine is the foundation, accounting for 19% of the capital cost.In addition, foundation installation with 6% of the capital cost is the highest cost compared with other parts [30].However, the cost of electricity using offshore wind is still high [31].As another offshore energy source, installing tidal turbines has attracted less investment because tidal turbines are exposed to harsh currents.Their lifetime is low, and foundation design is complex in most cases, where the water depth is more than 30 metres [32].However, tidal turbines can produce an enormous amount of electricity, more than four times per square meter of the rotor than wind turbines [33].Integration of both wind and tidal turbines with the same foundation may be a way to reduce the cost of electricity [7] and enable predictable power generation from two different energy sources.
Although New Zealand is surrounded by water and has good potential for offshore energy, it has not yet been used for power generation.In recent years, several reports indicated the annual demand of electricity increases from current demand of 40 TWh to 70 TWh by 2050 [34].Therefore, looking for new sources of harvesting power generation is essential.
This paper describes a preliminary design for an offshore structure capable of supporting a hybrid assembly of one wind plus two tidal turbines, as shown in Figure 1.The monopile has been found to be a suitable foundation type; it is one of the most inexpensive solutions for supporting the structures and is widely used in wind farm projects.Furthermore, the other reasons of choosing a monopile for integrating wind and tidal turbines are the ability to be driven into the seabed and connect directly to the tower, its simple structure, and being widely used in wind farm projects [35].
The design will be carried out using the foundation concepts of an offshore design [36].The design procedure has three steps:  The monopile has been found to be a suitable foundation type; it is one of the most inexpensive solutions for supporting the structures and is widely used in wind farm projects.Furthermore, the other reasons of choosing a monopile for integrating wind and tidal turbines are the ability to be driven into the seabed and connect directly to the tower, its simple structure, and being widely used in wind farm projects [35].
The design will be carried out using the foundation concepts of an offshore design [36].The design procedure has three steps:  Reducing the cost of electricity generation and integrating renewable energy sources are two essential factors in encouraging the development of novel ideas to tackle the lack of enough electricity and proposing alternatives for fossil fuels [16].

Environmental Parameters for Design
The MetOcean model identifies the Cook Strait between the North and South Island of New Zealand as the best area for offshore supplies, as shown in Figure 2 [37].
Water 2022, 14, 3555 4 of 18 Reducing the cost of electricity generation and integrating renewable energy sources are two essential factors in encouraging the development of novel ideas to tackle the lack of enough electricity and proposing alternatives for fossil fuels [16].

Environmental Parameters for Design
The MetOcean model identifies the Cook Strait between the North and South Island of New Zealand as the best area for offshore supplies, as shown in Figure 2 [37].The main geographical parameters of the optimized site in the Cook Strait are shown in Table 1.The most important data from NIWA [38] 's analysis is summarized in Table 2.The main geographical parameters of the optimized site in the Cook Strait are shown in Table 1.The most important data from NIWA [38] 's analysis is summarized in Table 2.The tidal information in the Cook Strait is tabulated in Table 3.The depth of the harbour mouth channel, where the turbines will be located, is an asset; it is neither too deep for access by divers if needed (31 m to a maximum 52 m) nor too shallow and therefore is not impacted by a lack of water at low tide.The sandbar surrounding the mouth protects the project from oceanic waves [40].
Table 3. Tide data for Terawhiti [41,42].Equivalent wind data will be sourced from the meteorological recording site closest to Terawhiti by NASA.These data are presented in Table 4 and Figure 3.These data are essential to estimate the wind stresses transmitted through the turbine's support structure to its foundation.The tidal information in the Cook Strait is tabulated in Table 3.The depth of the harbour mouth channel, where the turbines will be located, is an asset; it is neither too deep for access by divers if needed (31 m to a maximum 52 m) nor too shallow and therefore is not impacted by a lack of water at low tide.The sandbar surrounding the mouth protects the project from oceanic waves [40].Equivalent wind data will be sourced from the meteorological recording site closest to Terawhiti by NASA.These data are presented in Table 4 and Figure 3.These data are essential to estimate the wind stresses transmitted through the turbine's support structure to its foundation.The Weibull two-parameter distribution function often describes wind speed variability.It is considered a standard approach for evaluating local wind load probabilities because it has been found to fit a wide collection of wind data [46].The Weibull shape and scale parameters are denoted by s and K, respectively.s is dimensionless, and it indicates how peak the site under consideration is, whereas K has a unit of wind speed (m/s), and it shows how windy the site is [47].The Weibull two-parameter distribution function often describes wind speed variability.It is considered a standard approach for evaluating local wind load probabilities because it has been found to fit a wide collection of wind data [46].The Weibull shape and scale parameters are denoted by s and K, respectively.s is dimensionless, and it indicates how peak the site under consideration is, whereas K has a unit of wind speed (m/s), and it shows how windy the site is [47].

Site
To calculate Weibull parameters, the frequency percentage of Terawhiti results by Homer is used in the Weibull calculator [43], which results in s = 1.98 and K = 7.99 m/s.
The turbulence intensity varies with mean wind speed, which for Terawhiti is equal to 7.10 m/s, and quantifies how much the wind varies, typically within 10 min [36].This value, I = 16%, may be obtained from the standard IEC 61400 [44].
Based on the DNV code, for heights above sea level (z) less than 60 metres, L k is 5.67z, and for z above 60 m, L k is 340.2 m [36].As the height above sea level is 87m, the turbulence integral length scale is 340.2 m in this case.

Methods
All calculations in this section are based on the design method used by Bhattacharya [36].The design criteria which will be checked for the possibility of a monopile design and design procedure, which are presented in Table 5 and Figure 4.

Parameter Limit
The maximum stress (σ m )-yield strength ( f yk ) To calculate Weibull parameters, the frequency percentage of Terawhiti results by Homer is used in the Weibull calculator [43], which results in s = 1.98 and K = 7.99 m/s.The turbulence intensity varies with mean wind speed, which for Terawhiti is equal to 7.10 m/s, and quantifies how much the wind varies, typically within 10 min [36].This value, I= 16%, may be obtained from the standard IEC 61400 [44].
Based on the DNV code, for heights above sea level (z) less than 60 metres, Lk is 5.67z, and for z above 60 m, Lk is 340.2 m [36].As the height above sea level is 87m, the turbulence integral length scale is 340.2 m in this case.

Methods
All calculations in this section are based on the design method used by Bhattacharya [36].The design criteria which will be checked for the possibility of a monopile design and design procedure, which are presented in Table 5 and Figure 4.
Table 5. Main criteria for foundation design [36].Design criteria specific to the selected turbines are presented in Tables 6 and 7.

Parameter
Water 2022, 14, 3555 7 of 18 IEC codes [49,50] as well as the DNV code [51] describe hundreds of load cases that need to be analysed to ensure the safe operation of turbines throughout their lifetime of 20-30 years.However, in terms of foundation design, not all these cases are significant or relevant.The main design requirements for foundation design are ULS (Ultimate Limit State), FLS (Fatigue Limit State), and SLS (Serviceability Limit State).Five load cases important for simplified foundation design are identified and described in Table 8.

E-1
Normal operational conditions.Wind and wave action in the same direction (no misalignment).

NTM at u R (U-1) 1-yr ESS (W-1) Collinear E-2
Extreme wave load scenario.Wind and wave action in the same direction (no misalignment).

E-3
Extreme wind load scenario.Wind and wave action in the same direction (no misalignment).

EOG at u R (U-3) 1-yr EWH (W-2) Collinear E-4
Cut-out wind speed and extreme operating gust scenario.Wind and wave action in the same direction (no misalignment).

E-5
Wind and wave misalignment scenario.Same as E-2, except the wind and wave are misaligned at an angle of φ = 90 • .Due to low aerodynamic damping, the dynamic amplification is higher in the cross-wind direction.

ETM at u R (U-2)
50-yr EWH (W-4) Misaligned at φ = 90 In Table 8, the Normal Turbulence Model (NTM) relates to the normal working conditions of the turbine.The Extreme Turbulence model (ETM) is for extreme turbulence conditions.The Extreme operating Gust (EOG) is the highest single occurrence wind load caused by a sudden change in the wind speed.ESS and EWH denote extreme sea state and extreme wave height, respectively.The significant wave height HS, used in ESS scenarios, is the average of the maximum one-third of all waves in the three hours, whereas the maximum wave height, Hm, used in EWH scenarios, is the maximum wave height for three hours [36].

Results
Initially, a finite element analysis was presented for different soils.Then, the results were used to determine wind and wave loads and then evaluated to see if the calculated dimensions of the monopile can result in an acceptable foundation design or not.

Finite Element Analysis
For the current application, an advanced analysis method represents a finite element, discrete element, or finite difference method.OPTUM G3 is used considering the different soils for foundation and how the type of soil affects the stability of the hybrid system.Optum CE develops fast, user-friendly software for the design of Geotech and Concrete structures.The software is developed with a focus on providing advanced FE analysis packages but at the same time making the tools accessible for engineering practitioners, including structural engineers, contractors, and building companies [48].Table 9 shows the parameters used by OPTUM for simulations.The unit weight of a soil mass is the ratio of the total weight of soil to the total volume of soil.The total mass of the structure after summarizing the weights of each element in Tables 6 and 7 is 1780 tonnes.Applying this load to the foundation, using OPTUM G3 [48], as shown in Figure 5, confirms that the soil type of soft ormedium sand is more stable with less displacement and dissipation.
Water 2022, 14, 3555 9 of 18 For the current application, an advanced analysis method represents a finite element, discrete element, or finite difference method.OPTUM G3 is used considering the different soils for foundation and how the type of soil affects the stability of the hybrid system.Optum CE develops fast, user-friendly software for the design of Geotech and Concrete structures.The software is developed with a focus on providing advanced FE analysis packages but at the same time making the tools accessible for engineering practitioners, including structural engineers, contractors, and building companies [48].Table 9 shows the parameters used by OPTUM for simulations.The unit weight of a soil mass is the ratio of the total weight of soil to the total volume of soil.The total mass of the structure after summarizing the weights of each element in Tables 6 and 7 is 1780 tonnes.Applying this load to the foundation, using OPTUM G3 [48], as shown in Figure 5, confirms that the soil type of soft ormedium sand is more stable with less displacement and dissipation.The results are shown in Table 10.The results indicate that maximum displacement and dissipation will occur for Stiffclay-MC soil and minimum displacement and dissipation are from Medium Sand-MC and Loose-Sand-MC, respectively.

Macro-Element Model
For estimating the natural frequency of an offshore foundation pile under load, a spring model based on the Euler-Bernoulli beam model (Figure 12) of a monopile foundation at the Terawhiti site is assumed with input parameters as follows:

•
The stiffness of 20 MPa is a typical value for the beam-on-elastic foundation sourced from Bowles [53] and OPTUM [48].The results are shown in Table 10.The results indicate that maximum displacement and dissipation will occur for Stiffclay-MC soil and minimum displacement and dissipation are from Medium Sand-MC and Loose-Sand-MC, respectively.

Macro-Element Model
For estimating the natural frequency of an offshore foundation pile under load, a spring model based on the Euler-Bernoulli beam model (Figure 12) of a monopile foundation at the Terawhiti site is assumed with input parameters as follows:

•
The stiffness of 20 MPa is a typical value for the beam-on-elastic foundation sourced from Bowles [53] and OPTUM [48].The results are shown in Table 10.The results indicate that maximum displacement and dissipation will occur for Stiffclay-MC soil and minimum displacement and dissipation are from Medium Sand-MC and Loose-Sand-MC, respectively.

Macro-Element Model
For estimating the natural frequency of an offshore foundation pile under load, a spring model based on the Euler-Bernoulli beam model (Figure 12) of a monopile foundation at the Terawhiti site is assumed with input parameters as follows:

•
The stiffness of 20 MPa is a typical value for the beam-on-elastic foundation sourced from Bowles [53] and OPTUM [48].The initial stiffness of the foundation (i.e., KL, KR, and KLR) can be determined based on the pile dimensions and soil type.Once KL, KR, and KLR are known, one can predict the system's natural frequency [54].The results for this design are: KL = 3848.25MN/m, KLR = −133,488 MN and KR = 7,252,848 MNm/rad.The simple cantilever beam formulas, as recommended by Arany [55], were used to estimate the natural frequency of the tower  , which is 0.34 Hz and which is acceptable, as the condition is that the target frequency of the selected wind and tidal turbines, according to Table 5, is 0.24 Hz [36].

Wind Loads
Table 11 summarizes the main parameters of wind scenarios.The loads and moments will be used later in Section 4.2.3 to identify driving combined scenarios, either E1 or E5.The maximum wind load and moment were found for U3.As recommended by DNV 2014 [51] and IEC 2019 [50], the environmental load factor of L = 1.35 multiplies on U3 moment load to result a total wind moment of 473.85 [MNm].The initial stiffness of the foundation (i.e., K L , K R , and K LR ) can be determined based on the pile dimensions and soil type.Once K L , K R , and K LR are known, one can predict the system's natural frequency [54].The results for this design are: K L = 3848.25MN/m, K LR = −133,488 MN and K R = 7,252,848 MNm/rad.The simple cantilever beam formulas, as recommended by Arany [55], were used to estimate the natural frequency of the tower f 0 , which is 0.34 Hz and which is acceptable, as the condition is that the target frequency of the selected wind and tidal turbines, according to Table 5, is 0.24 Hz [36].

Wind Loads
Table 11 summarizes the main parameters of wind scenarios.The loads and moments will be used later in Section 4.2.3 to identify driving combined scenarios, either E1 or E5.The maximum wind load and moment were found for U3.As recommended by DNV 2014 [51] and IEC 2019 [50], the environmental load factor of γ L = 1.35 multiplies on U3 moment load to result a total wind moment of 473.85 [MNm].

Wave Loads
The wave conditions recommended by Bhattacharya [36], as explained before in Table 2, are used for calculating critical wave loads acting on the substructure which is the summation of maximum inertia loads and maximum drag loads.The maximum inertia load occurs at the time instant t = 0 when the surface elevation η = 0 and the maximum of the drag load occurs when t = T/4 and η = H/2.Current loads due to the movement of water particles causing drag which are considered as a portion of wave loads according to above explanation.
The dynamic amplification of wave loading is calculated using the peak wave frequency and an assumed damping ratio as shown in Table 12.The total damping ratios for the along-wind (x) and cross-wind (y) directions are chosen conservatively as 3% and 1%, respectively, by Camp et al. (2004) [56].
In calculating DAFs, as the difference in DAF x and DAF y for wave scenarios are negligible, a higher value is applied to loads.The chosen values of D P and L P satisfy the above conditions.Therefore, the pile dimensions for the Terawhiti site to withstand total load are: Based on the criteria design (Table 5), as ρ < 0.2 m and θ < 0.5 • , the pile tip deflection and the rotation are acceptable.

Conclusions
This paper proposes a standard design for the foundation of a hybrid (wind+tidal) system for Terawhiti:

•
The proposed tower is a hollow steel tube wall with a thickness of 0.027 m, 68 m high above the platform, tapering from 5 m at the base to 3 m at the top, and weighing 255 tonnes.

•
The proposed transition piece is a steel tube with an internal diameter of 6 + 2×83 1000 = of 6.16 m to fit the top of the monopile, wall thickness of 0.083 m and extending 29 m below the platform level, and sheathing on top of the monopile.Weight: 300 tonnes.

•
The proposed foundation is a monopile inserted into the seabed.It would be solid steel, 6 m in diameter, and 60 m long, weighing 700 tonnes.It would project above the seabed for 30 m (the upper 20 m would be inserted into the transition piece), and the lower 20 m would be placed in the seabed.The pile would be driven with a hydraulic hammer into the seabed.

•
The acting loads are transferred to the foundation; they can be static depending on the total weight of the structure, which is calculated and analyzed with OPTUM G3 software, or dynamic (cyclic), which is investigated by combining wind and wave loads.

•
The wind and water produce aerodynamic and hydrodynamic loads (thrust and drag) on the structure, which depend on the operational speed of turbines.However, to know the acceptability of foundation design, it is necessary to combine wind and wave loads in ULS design and calculate maximum loads and find the driven scenarios.
Then, find the required dimensions of the pile and, based on the maximum load of the driven scenario, calculate deflection and check in ULS if the deflection is allowable or not.

•
The combination of wind and wave loads indicates that the maximum load occurs for the E-3 scenario.Applying loads of this scenario results in acceptable deflection, tilt, and natural frequency for Terawhiti.

•
Several iterations were done to reach the required pile dimensions after finding the maximum combined load for the driving scenario.

Figure 1 .
Figure 1.Schematic of a hybrid system consisting of wind and tidal turbines.
(a) Site investigation; (b) Criteria for design; (c) Evaluation of the stability of design under combined loads.

Figure 1 .
Figure 1.Schematic of a hybrid system consisting of wind and tidal turbines.
(a) Site investigation; (b) Criteria for design; (c) Evaluation of the stability of design under combined loads.

Figure 4 .
Figure 4. Design Procedure of Offshore Wind and Tidal Turbines Monopiles.Figure 4. Design Procedure of Offshore Wind and Tidal Turbines Monopiles.

Figure 4 .
Figure 4. Design Procedure of Offshore Wind and Tidal Turbines Monopiles.Figure 4. Design Procedure of Offshore Wind and Tidal Turbines Monopiles.

Figure 5 .
Figure 5. Applying load to the structure using OPTUM.After simulation by OPTUM, the results for different kinds of soils are represented in Figures 6-11.

Table 1 .
The main geographical parameters of the site for foundation design.

Table 1 .
The main geographical parameters of the site for foundation design.

Table 9 .
Geotechnical Parameters used by OPTUM software for simulations.

Table 9 .
Geotechnical Parameters used by OPTUM software for simulations.

Table 10 .
OPTUM results for different types of seabed.

Table 10 .
OPTUM results for different types of seabed.

Table 10 .
OPTUM results for different types of seabed.

Table 12 .
Dynamic amplification factors and wave loads.

Table 13
uses the calculated loads of Tables11 and 12to find combined loads of different scenarios of Table8.It can be seen that superior loads belong to E-3.

Table 13 .
Calculated wind and wave loads.Substituting the total overturning moment of 515.3 MNm from Table13and other values mentioned above in Equation (A5): × 515.3 → D P < 1.25I P Substituting the above value (D P = 1.25IP ) in Equation (A3) in Appendix ??, results in finding area moment of inertia (I P ) and monopile diameter (D P ) as depicted below:I P = 5.12 kg•m 2 → D P < 1.25 × 5.12 = 6.414 m = 6414 mm Substituting D P in Equation (A2) results in the required thickness: Therefore, based on total load, the foundation dimensions should be: D P < 6.41 m, t P ≥ 70.49mm, L P ≥ 48.27 m