Evaluating the Impacts of Rice-Based Protection Dykes on Floodwater Dynamics in the Vietnamese Mekong Delta Using Geographical Impact Factor (GIF)

This study aims at evaluating the geographical influences of rice-based protection dykes on floodwater regimes along the main rivers, namely the Mekong and the Bassac, in the Vietnamese Mekong Delta (VMD). Specifically, numerous low dykes and high dykes have been constructed particularly in the upper delta’s floodplains to protect the double and triple rice cropping against the annual flooding. For the whole deltaic domain, a 1D-quasi-2D hydrodynamic model setup was used to simulate seventy-two (72) scenarios of dyke construction development in the context of low, medium, and high floods that occurred in the VMD to examine the effects of different flood magnitudes on a certain dyke construction area. Based on the model simulation results, we established an evaluation indicator, the so-called Geographical Impact Factor (GIF), to evaluate the impacts of zone-based dyke compartments on the floodwater regimes along the main rivers for different kinds of floods. Our findings revealed different rates of influences on the floodwater levels along the Mekong and Bassac Rivers under different scenarios of zone-based high-dyke developments. GIF is a useful index for scientists and decision-makers in land use planning, especially in rice intensification, in conjunction with flood management for the VMD and for similar deltas worldwide.


Introduction
Being home to over 17 million people, the Vietnamese Mekong Delta (VMD) is the agriculturally most productive region of the nation. It contributes approximately 50% of the national rice production with 90% of the rice exports, produces 70% of the fresh tropical fruits and 60% of the aquaculture and fisheries, and accounts for 34% of the poultry for the country [1,2]. However, the delta has been facing several natural challenges due to river-bed mining and dyke construction [3], coastal erosion [4], land subsidence [5], salinity intrusion [6,7], hydropower dam developments [8], and especially flooding [3,9,10]. In addition, the VMD is one of the deltas most vulnerable to increased flooding with climate change [8,11] and sea level rise [12][13][14].
As shown in Figure 2, the VMD is located in the lower part of the Mekong River with an area of about 3.9 million hectares accounting for 5% of the Mekong River basin [6]. Due to the physical conditions of low-lying topography with a large proportion of areas below +2 m above mean sea level, it is annually impacted by flooding from the upstream areas. Floods usually start in June/July and end in November/December, causing an inundated depth of 0.5 to 4.0 m to an area of 1.9 million hectares of the delta [15,16]. Flooding is a normal phenomenon in the VMD, and the local people refer to it as "floating season". Typically, annual floods are essential to conserve the floodplain biodiversity and to supply natural fishes as well as fertile sediments for farm production in the delta [2]. The people in the delta therefore have a traditional alternative, the so-called "living with floods", to make floodwaters indispensable to the agricultural production in the VMD [17,18]. However, extreme flood events pose a threat to people and properties [10,19,20].
Flood magnitude in the VMD is classified by the water levels measured at Tan Chau station, see Figure 1. Based on the conventional observations, when the water level at Tan Chau is below 4.0 m, the magnitude is defined as a low flood. When the water level is between 4.0 m to 4.5 m, it is referred to as regular or normal flood; and when the water level is above 4.5 m, it is considered a high flood [21]. According to Kuenzer et al. [22], the flood regime in the Mekong Delta is defined by a combination of four influences, including (i) the flood inflow mainly induced by the flood flow on the Mekong River and transborder flow; (ii) flood due to high local rainfall intensity; (iii) the tidal flood primarily during spring tide and in particular with a storm surge condition; and (iv) man-made flood due to development activities in the delta. Flood occurrences are triggered by a combination of several of these factors. As a result, the potential flood risk in VMD is not only caused by the natural conditions but also the impacts of human activities with hydropower plants upstream and the land use strategy in the delta [11,[22][23][24][25].   [26].
Since the adaptation of the innovative policy "Ðổi Mới" by the Government of Vietnam in 1986, the Vietnam's economy has transformed from a centrally-planned model to the market oriented one [27]. As a result, in the field of agriculture, the development of intensive rice cropping has been rapidly expanding in the VMD [28]. Therefore, the delta is popularly known as the largest "rice bowl" of Vietnam. Notably, the shift to triple rice cropping from double rice cropping has made Vietnam one of the top rice-exporting countries in the rice market worldwide [29]. However, the construction of dyking system in the deep-flooded zones, such as the Plain of Reeds (PoR) and the Long Xuyen Quadrangle (LXQ), may cause negative impacts on the water regimes in downstream areas. Figure 3 presents some pictures of low dyke and high dyke performance during the flood season as well as a map of spatial distribution of dykes in the VMD surveyed by the Southern Institute of Water Resources Research (SIWRR) in 2011, herein the dyke is classified based on the crest elevation. When the crest of dyke is below +4.0 m, it is considered as low dyke, whereas the crest is equal or higher than +4.0 m, it is defined as high dyke. Whereas low dykes aim to protect the two rice crops against floodwater until the middle of August, high dykes are intended to protect the triple rice fields from the flood completely. Several researches about flooding have been implemented in the VMD to support authorities and administrators in land use management in conjunction with flood management based on the rapid development of technologies and computer sciences. By simulating the floods of 1996, 2000, and 2007, the studies by Hoa et al. [15,16] concluded the impacts of human-made dyke systems on floods. Besides, Van et al. [30] revealed the impacts of dykes on the flooding regimes in the Long Xuyen Quadrangle in 2011 and the boundary conditions in 2000. In addition, the relation of land use patterns in the last decade with flooding regimes in the VMD was studied by combining hydraulic modelling with satellite technology. Duong et al. [20] analysed the impacts of high dykes on the change of flood water levels along the Mekong and Bassac Rivers based on the boundary conditions of two historical flood events in 2000 and 2011 using the numerical model MIKE11. Similarly, Triet et al. [9] used the MIKE11 model to simulate the projections also for the two high floods in 2000 and 2011 to identify the reasons for the change in flood level along the Mekong Rivers. In their research, they expressed the reasons for this change mainly due to (i) high dyke development for triple rice cropping in upstream provinces, (ii) the effects of tidal levels due to sea level rise and land subsidence, and (iii) the temporal coincidence of high water levels and spring tides. Additionally, Tran et al. [10] expanded the research done by Van et al. [30] to assess the impacts of dyke construction in the LXQ on the flood dynamics along the Bassac River by using the numerical model MIKE11 to evaluate the impact of different projections of dyke construction in the LXQ based on the boundary conditions of two high floods in 2011 and a medium flood in 2013. Recently, Thanh et al. [31] introduced a new approach of using DELFT3D Flexible Mesh to analyse the flood distribution in the VMD due to the construction of high dyke. They evaluated the impacts of high dykes in the LXQ and PoR with the boundary conditions of high floods in 1981, 1991, and 2000. Last but not least, Triet et al. [13] examined the projections in flooding hazard and agricultural production due to different scenarios of human activities between two periods of baseline  and future (2036-2065). The study found that sea level rise and land subsidence are the major factors for the changes in flood hazard and influenced on rice cropping, the secondary factors relating to the development of hydropower in upstream countries as well as the impact of climate change.
Satellite remote sensing is a valuable tool for objectively detecting inundated areas. Therefore, several studies have been undertaken for flood monitoring in the VMD. For instance, Kunzer et al. [22] monitored the impacts of artificial dyke to flooding situation in the VMD based on radar satellite products from 2007 to 2011. Besides, Sakamoto et al. [32,33]   To the authors' knowledge, the impacts of zone-based high-dyke compartments on the floodwater dynamics and flood water levels in the VMD have not yet been studied comprehensively. Particularly, all previous studies focused on the assessment of the impacts of high dykes on the flooding situation along the Mekong Rivers based on high-flood conditions. Only Tran et al. [10] examined high floods and medium floods as boundary conditions, however in their study, they focused only on the scenarios of dyke construction in the LXQ and their influences on the Bassac River. Until now, the high dykes for triple rice production have been developed extensively across the upper floodplains of the VMD. The development has raised the question as to whether flood risk will increase downstream also under the conditions of medium-and low-floods if a particular part of the delta will be provided with dyke compartments in the future. This study aims to fill the knowledge gap by using a 1D-quasi-2D hydrodynamic model to run various zone-based high-dyke compartment scenarios to establish a Geographical Impact Factor (GIF). The GIF is expected to serve as a new index that helps the local authorities and decision-makers to immediately identify the impacts of dyke developments on flooding levels along the Mekong Rivers in any kind of flood discharge at any geographical location and area of the compartments. The findings in terms of water level dynamics are useful to provide administrators and decision-makers with a proper strategy for land use plans in conjunction with flood management.

Model Setup
In this study, the Mike 11 hydrodynamic module (1D) is applied to represent the river network in the Mekong Delta which has one of the largest estuaries in the world with a highly complex hydraulic system [35]. The MIKE 11 model developed by Denmark Hydraulic Institute (DHI) uses an implicit finite difference scheme for the computation of unsteady flows in rivers and estuaries. It applies a dynamic wave description to solve the vertically integrated equations of the conservation of continuity and momentum referred to as Saint Venant equations [36]. This has been described in previous studies to serve modelling of water levels and floods for the whole VMD and its floodplains [9,10,13,20,35,37,38].
The Mekong River network's geometry was rebuilt and improved based on the old river networks, which were kindly provided by the Institute for Water and Environment Research (IWER) and the Southern Institute for Water Resources Research (SIWRR), Vietnam. As shown in Figure 5, the network contains 3270 regular branches, 425 floodplains, and 358 weirs at the canals along the coast to control salinity intrusion in the dry season. In the flood season, these salinity control structures are freely open to discharge the floodwater to the sea. The upstream boundaries include the discharges at Kratie, Tonle Sap Lake on Cambodian territory, Tri An, and Dau Tieng reservoirs. In contrast, the downstream boundaries are the time series of water levels in the East Sea and the West Sea estuaries. Boundary conditions and descriptions are discussed in previous studies, i.e. [9,10,20,34,35]. The hydrological data used as inputs for the boundary condition and model calibration process were collected from several sources. Specifically, the water levels, rainfall, and discharge in 2000 and 2011 were collected from the IWER and SIWRR; the Digital Elevation Map (DEM) with a resolution of 90 m was kindly provided also by SIWRR. The water levels and discharge and rainfall in 2012 and 2013 were provided by the National Centre for Hydro-Meteorological Forecasting (NCHMF). Daily rainfall data were collected from seven meteorological stations in Cambodia and 20 stations in Vietnam. The surface water contributed to rivers and canals was described by the Thiessen polygons. Specifically, the rainfall run-off links include 326 sub-regions with data from rainfall gauges for each. The rainfall discharge was calibrated using the RR module in the Mike11 NAM.
Floodplain is the vital domain installed in the model to demonstrate the flooding situation in the VMD. The Mike 11 model has a capability to account in a realistic way for floodplain storage during flood events although a two-dimensional (2D) model is usually required to simulate the flood dynamics of a floodplain. Specifically, two approaches that have often been applied in previous studies could be considered for VMD floodplain simulation by use of MIKE 11. In the study by Dung et al. [35], most of the compart-ments represent a closed system surrounded by dykes and channels, hence flood cells are modelled by artificial branches with low and wide cross sections linked to the channels by control structures. Here, weirs were used to represent dykes and dyke overflow, and sluice gates were used whenever information on existing sluice gates was available. In this study, the link channel geometry conceptualized by DHI [36] was introduced to typically comprise the definition of a longitudinal geometry of the embankment along the river (Figure 5a). By using the method, we set up numerous water storage areas represented for the floodplains and determine specific elevations of dyke crests that prevent floodwater from entering into the floodplains to complement the floodplains into the 1D model, it is namely 1D-quasi2D hydrodynamic model.
Link channels are used to simulate the floodplains components in the MIKE11 as shown in Figure 4, the link channels connect to the branches or rivers and keep an important function as additional flooding storage areas. For detailed information about the link channels, please see the MIKE 11 User manual [36].
The floodplains were set up with the exact crest elevations of low dykes and high dykes based on the surveyed data provided by SIWRR as shown in the Figure 3. However, the surveyed data was available only for the An Giang, Dong Thap, Long An, and Kien Giang provinces. For other provinces, such as Can Tho, Vinh Long, and Tien Giang, we used the MODIS water mask to identify the "dried areas" to put into the hydraulic model as high-dyke protection areas during the calibration and validation process for the floods under the dyke conditions in 2011, 2012, and 2013.
In the process of running each separate scenario of high-dyke compartment to prevent the floodwater from entering into the floodplains due to the construction of high-dykes, we put the crest of the link channel to up to +6.00 m. In view of the fact that the peaks of the high floods in 2000 and 2011 were only +5.06 m and +4.89 m, respectively, the floods thus could not overflow into the floodplains studied. Although both approaches show good results after calibration, the approach adopted in this study is faster (around 45 min each scenario) and more valuable to flood simulation in comparison to the approach by [9,10,35] that requires more work for preparation of the input data and more time for simulation (around 4-5 h) due to the operation of numerous weirs and artificial branches for the floodplains.

Model Calibration and Validation
The model needs to be calibrated and validated with the observed discharge and water level at the gauge stations. This is done by comparing calculated and measured water levels or discharges and correspondingly adapting the model generally by adjusting Manning's hydraulic roughness coefficients [10,12]. Considering the unsteady nature of the flow, the roughness coefficient was applied in the branches and link channels in the MIKE 11 model where the flow is uniform or quasi-uniform. In this study, the calibration of the channel/floodplain roughness coefficients for the Mike 11 model was used to compensate the uncertainty of river cross-sectional geometries, river morphology, bed elevation approximation, and inflow boundary conditions. A trial and error method was applied to adjust the floodplain roughness to best fit the observed stage and discharge measurements at multiple measured sites. For a dense and complex river system as Mekong river, the first important step is to calibrate the discharge and water level along the main rivers, the values of hydraulic roughness range from 0.014 to 2022 near the coast and from 0.028 to 0.030 for the upstream section, after all stations on the main rivers were well calibrated with the observed data, we calibrated further for the inland stations by adjusting the roughness coefficient for canals and the floodplains. The inland canals have the roughness coefficient from 0.028 to 0.030, while the floodplains are mainly vegetation and rice fields, therefore they have highest flow resistance due to emergent rigid and flexible vegetation [39], hence the Manning coefficient range from 0.033 to 0.035 [40]. The ranges of Manning's coefficient for different sections of channels and rivers were presented in Table 1.  Figure 6 shows the locations of hydraulic gauges placed on the main rivers and inland canals used for the calibration and validation in this study. To be more precise, the Mike 11 was calibrated and validated according to the following gauges: In the calibration and validation process, the Nash-Sutcliffe index value (E) was used to evaluate the model accuracy [10,35]. When the E index is from 0.60 to 0.75, the model performance is considered as low accuracy, in case the E index is between 0.75 to 0.85, the model is examined as medium accuracy; when the E index is in the range from 0.85 to 0.95, it is defined as high accuracy; and when the E index meets the requirement of from 0.95 to nearly 1, the model performance is evaluated at very high accuracy.
The Nash-Sutcliffe index (E) is calculated based on the following formula: where Q 0 is the mean of the observed data, Q t m is the modelled data, and Q t 0 is the observed data at time t.

Assumption of Dyke Compartment Development in the VMD Floodplains
Based on the maximum flood extent of 30.10.2000 presented in Figure 4, we separated the flood extent in the upper VMD into 22 key compartments, each of which is certainly bounded by main canals or rivers (see Figure 7 and Table 2). These compartments belong to four zones based on the hydrological characteristics of the watershed. First, Long Xuyen Quadrangle (LXQ) includes six (06) compartments (A1 to A6) along the main canals of Tri Ton, Mac Can Dung, Rach Gia-Long Xuyen, Cai San, and Bassac River. Second, the Western of Bassac River (WBR) consists of three (03) compartments (A7 to A9) following KH6, Thi Doi canals, and the Omon-Xano system. Third, three compartments (A10 to A12) are parts of the middle zone between the Mekong and the Bassac Rivers (MID), based on Vam Nao, Cai Tau Thuong, and Nha Man-Tu Tai Rivers. Finally, the Plain of Reed (PoR) comprises ten (10)   Currently, there are no indices for evaluating flood management in conjunction with land use in the Mekong Delta to set up a scientific basis and helpful index to support the administrators and planners in establishing land use development strategies in the VMD. Therefore. we defined an indicator, i.e. the Geographical Impact Factor (GIF) to quantify the impact of high-dyke measurement on rice cultivation at each compartment. It is defined as follows: where GIF i is the geographical impact factor at compartment i; Z baseline is the water level at a considered point on the Mekong and Bassac Rivers with no-dyke systems at 22 compartments (cm); Z i is the water level at a considered point with high-dyke systems at compartment i (cm); Z total is the water level at a considered position due to high-dyke systems at 22 compartments (cm); and A i is the area of compartment i (in hectares).  Table 3 shows 72 dyke scenarios carried out in this study. The scenarios were classified into three (03) model sets under the small, medium, and high floods. The first set included three scenarios corresponding the three floods, which were defined as being without any dyke system for all 22 compartments. The second set consisted of 66 scenarios, each of which was set up as one individual compartment under high-dyke protection and 21 compartments without dykes. The third set has three (03) scenarios, each of which covered the whole 22 high-dyke compartments. Ten (10) positions were examined to analyse the influences of high-dyke measurements on the water levels along the main rivers (Figure 7). These positions are located on the Mekong River (P1 to P5) and the Bassac River (P6 to P10).

Results of Model Calibration and Validation
The model calibrations were carried out for the high floods in 2000 and 2011, whereas the validations were carried out for the medium flood (2013) and the low flood (2012). The accuracy and agreement have been evaluated through the Nash-Sutcliffe index ranges between 0.98 to 0.65 and compared with flood maps of MODIS satellite. Table 4 illustrates the accuracy in the calibration of the water levels (WL) and discharges (Q) at the gauging stations located on the Mekong River, such as Tan   The flood distribution was analysed using hydraulic models and remote sensing for two high-flood years in the years of 2000 and 2011 with good agreements as illustrated in Figure 8. In the satellite products, the coastal areas also appeared as flooded due to the impact of the tides, not the impact of flooding from the upstream Mekong River. Flood extension in the satellite products was interpreted based on the algorithms by [32] for the MODIS satellite. The accuracy of the MODIS flood maps was found to be in good agreement with the ground truth and the results from the radar satellites [26]. The flood maps from the hydraulic model of Mike 11 present both the flood extension and water depth while flood maps from the MODIS satellite can display only the flood extension. The flood maps from a 1D model were processed based on the Triangulated Irregular Network (TIN) method to build a surface of water map from a set of irregularity spaced points which is processed in the GIS program. The flood maps were implemented by subtracting the water map with the topographical map. If the pixel value is positive, the water is higher than the ground. Therefore, these pixels are considered to represent flood. When the pixel values are zero or negative, the water level is equal to or lower than the ground, and hence there is no flooding.
Based on the simulation and validation results, the 1D-quasi2D hydraulic model of Mike 11 is considered as an appropriate tool to simulate the flood hazards of a large and complex river network dominated by numerous hydraulic control structures such as the VMD. It demonstrated acceptable levels of accuracy for hydraulic gauges and flood distributions as compared to flood mappings of satellite products.  Figure 9 shows the geographical influence of high-dyke construction scenarios on the river water levels based on the GIF analysis. Overall, the closer to the main rivers the high-dyke constructions, the greater the impacts. The scenarios of upper high-dyke constructions between the two main rivers (A10, A11, and A12) cause the highest influence on the increase in river water levels, whereas the lower impacts are found with the dyke constructions along the right banks of the Bassac River (A1, A3, A5, A7, and A9) and the left banks of the Mekong River (A15, A17, A19, and A21). The construction of dyke compartments at A2, A4, A6, and A8 in Kien Giang province cause no influence on the water levels due to their far distance from the main rivers. The floods therefore will discharge mainly along the main Mekong and Bassac Rivers and partly overflow the PoR and LXQ. This is similar at A14, A16, A18, A20, and A22 in Long An Province. In these areas, The influence of dyke construction on the flood water level is very small. The high-dyke construction in the A10 compartment is sensitive to the water level changes in the Mekong and Bassac Rivers, and these changes depend on the magnitude of floods ( Figure 10). This compartment is the Bac Vam Nao area of An Giang province, which is the first area of the VMD that receives flood water from upstream of the Mekong River, hence the high-dyke systems have prevented the floodwater from delivering from the Mekong River to the Bassac River. As a result, even though the compartment increases the water level at Tan Chau (P1), a decrease in the river stage at Chau Doc (P6) is found. The same pattern of the water level changes is identified at Vam Nao 1 (P2), but this no longer exists after Cao Lanh (P3). However, along the Bassac River, the water level changes remain until Dai Ngai (P10). Although the government does not promote dyke construction in this region and encourages to use a 3-3-2 cycle in Bac Vam Nao [21], there is still an effect when the gate is closed because the A10 is very sensitive to the dyke system. Regarding the small floods, the GIF10 indicates a strong impact of the A10 on the water level along the Mekong River. However, this tendency is reduced with medium and high floods. On the Bassac River, the influence of A10 on the water level at Chau Doc (P6) is relatively high with high floods, but decreases with medium and small floods. This impact has the same characteristics at the locations of Vam Nao 2 (P7), Long Xuyen (P8), and Can Tho (P9) with very small values along the river. Figure 11 below presents the influence of compartment A20 on the main river water levels. For different kinds of floods, the construction of a dyke compartment at A20 causes no impact on the flood levels in the Mekong and Bassac Rivers due to the compartment's geographical location far away from the main rivers. Figure 11. GIF of compartment A20 on the flood water levels along the Mekong and Bassac Rivers.

GIF-Based Sensitivities of the Influences of Geographical Dyke Compartment Scenarios on Flood Water Levels in Terms of Flood Magnitudes
The geographical location of high-dyke compartments and the magnitude of floods had different levels of impact on the water level at Tan Chau (P1), see Figure 12. With low floods, the construction of high-dyke at almost compartments cause small impact on the water level at Tan Chau, except at the compartments of A10, A11, and A15, relatively high. The impacts decrease significantly from low to medium floods but reduce slightly from medium to high floods. In contrast, the A17 compartment has quite a small effect with low floods, whereas the influence increases slightly with medium flood and rapidly with the high flood. The findings imply consideration on the part of the authorities before implementing land use changes for rice production based on high-dyke protections.
The high-dyke compartments also have various influences on the water level at Chau Doc (P6) (also see Figure 12). Generally, most of the compartments with a high-dyke system cause relatively low impacts on the water level at this point. Exceptionally, the A1 compartment causes a relatively high effect on the water level. This tendency is stable for small and medium floods but increases sharply in the case of high floods. In contrast, the A10 compartment increases the water level at Tan Chau (P1). It decreases the water level at Chau Doc (P6) because the high-dyke construction in this compartment prevents the flood water from entering from the Mekong River to the Bassac River. This tendency is more apparent with medium and high floods.
As shown in Figure 13, dyke measurements at the compartment of A11 are very sensitive to the change in water level at Vam Nao (P2) on the Mekong River. The A12 compartment causes a relatively high impact on both main rivers, Cao Lanh (P3) and Long Xuyen (P8), in high floods. Afterwards, the impact decreases in medium and low floods. Besides, the A10 compartment slightly raises the water level at Vam Nao (P3) and reduces the water level at Long Xuyên (P8) due to preventing floodwater from overflowing from the Mekong River to the Bassac River. Surprisingly, the A9 compartment associated with the Omon-Xano infrastructure system causes a high impact on the water level at Long Xuyen (P8). The impact is slightly higher than the influence of compartment A11, although A9 is located further downstream the Bassac River.  Dyke measurements at the compartments of A11 and A12 are sensitive to the changes in water levels at Cao Lanh (P3), whereas those at A9 and A11 have a great influence on the water levels at Can Tho (P9), see Figure 14. The A12 compartment has a relatively high impact on Cao Lanh (P3) and Can Tho (P9) in low floods, but the impact decreases in medium and high floods. Besides, the A11 compartment raises the water level at Cao Lanh (P3). It reduces the water level at Can Tho (P9) due to preventing floodwater from overflowing from the Mekong River to the Bassac River.
It is also shown in Figure 14 that the influence of the A11 compartment on the water level decreases with medium and high floods. Remarkably, the A9 compartment indicates a high impact on the water level at Can Tho (P9). The tendency of high-dyke effects on these compartments decreases gradually with medium and high floods. However, the high-dyke impacts are insignificant for other compartments.
The construction of high dykes for the whole Mekong River causes highest impact in terms of water level change along the main rivers, however GIF_full is smallest for all types of floods at any location along the Mekong and Bassac Rivers, because the total area of dyke construction in the region is the largest with 1.337.000 ha, see GIF_full in Figures 12-14 above.

Conclusions
The extensive construction of low dykes and high dykes within the floodplains of the Vietnamese Mekong Delta (VMD) to protect the rice cropping against flooding has caused impacts on the flooding levels along the Mekong Rivers. This study used the 1D-quasi-2D hydrodynamic model setup for the whole deltaic domain to simulate scenarios of dyke construction development in the context of low, medium, and high floods after the high performance of calibration and validation processes with hydrological data and satellite products. Notably, we applied a link-channel method to perform flood dynamics overflowing into the floodplains that helped the model run faster and more stable than previous studies using artificial dyke cells. Based on the numerical simulation results, we established the Geographical Impact Factor (GIF) to reveal the geographical influences of rice-based land use scenarios in the upper floodplains of the VMD under high-dyke protections on the river water levels. The research findings lead to the following conclusions:

•
Overall, the high-dyke developments for land use purposes cause relatively minor impacts on the water levels in the Mekong and Bassac Rivers. However, the high-dyke measurements at multiple compartments in the middle zone indicate higher effects on the water levels at Tan Chau, Chau Doc, Cao Lanh, and Can Tho. Besides, the compartment of A9 (Omon-Xano system) would be susceptible to the increase in water level at Can Tho in the case of the high-dyke system built in this area. • Different flooding magnitudes such as high-, medium-, and low-floods cause different influences on flood water along the Mekong Rivers if the compartment is located in the middle zone (A10, A11, A12) or near the main rivers (A1, A3, A5, A7, A9, A13, A15, A17, A19, A21), when the dyke compartment locates outside the middle zone and far from the main rivers (A2, A4, A6, A8, A14, A16, A18, A20, and A22), the impact of different flood magnitudes is negligible.

•
The GIF has been established to help scientists and planners in various aspects. It could anticipate a possible impact of the dyke-based measures on the water level along the main rivers. Therefore, any construction of high dykes at any location in the Mekong Delta would be quickly assessed under all kinds of flood conditions. The GIF would also be a scientific basis for developing a flood level estimation method (FLEM) for flood water level prediction along the Mekong Rivers [42]. • Agricultural production plans under high-dyke protections could be assessed and optimised according to the rivers' accepted flood water levels. The smaller the GIF identified for any high-dyke compartment, the better the triple rice production cultivated in that compartment.