A Systemic Analysis of the Environmental Impacts of Gold Mining within the Blyde River Catchment, a Strategic Water Area of South Africa

: Exploratory modelling of the impact of gold mining on groundwater in a strategic water area of South Africa was undertaken. A systems dynamics (SD) model was developed to simulate the impact of gold mining on water quality, focusing on groundwater contamination risk, within the context of competing developmental priorities around water resource development and the socio-economic gains from gold mining. The model also identiﬁed interventions to minimise the impacts by the year 2040. The study area was the Blyde River Catchment (BRC), which is part of the Olifants Water Management Area in South Africa. This area is an important contributor, currently and in the future, to freshwater ﬂows and groundwater in the Olifants River Catchment, which is one of South Africa’s most economically important catchments. The model development process included a causal loop diagram–based problem conceptualisation, followed by the drawing of stock-ﬂow diagrams and the determining of model parameters based on a combination of background literature, data from environmental impact assessments, and from the national Department of Water and Sanitation. The model showed the potential environmental risks of gold mine wastewater production and interventions to minimise these risks. The most effective intervention identiﬁed to reduce the risk of groundwater contamination was the development and use of synthetic-lined tailings dams. The baseline simulation result of sulphate loading of 5430 t/year can be reduced by 3070 t/year to give a simulated sulphate load of 2270 t/year in 2040 using this intervention. In comparison, the simulated wastewater recycling intervention only reduced the sulphate load to 4630 t/year and the wastewater treatment interventions to 3420 t/year. This project contributes to the exploratory modelling of an understudied region of the Olifants River Catchment that is a crucial provider of freshwater ﬂows to the Olifants, which is threatened by increasing gold mining in the upper BRC. The SD model highlighted the importance of protecting the dolomitic aquifers in the BRC for the long term sustainability of the catchment, which is particularly important if groundwater development occurs.


Introduction
Global water systems, which are responsible for sustaining the natural environment, development and rapid population growth, are under stress due to increased demand and pollution [1]. South Africa is one of the many countries that are experiencing water scarcity, which is defined as being unable to meet the particular region's water requirements [2]. This paper reports on the impacts of gold mining on groundwater in the Blyde River Catchment (BRC), which is part of the Mpumalanga Drakensburg SWA (Figure 1). A system dynamics (SD) model was constructed to analyse the potential risk for groundwater and to determine which interventions would enhance the mitigation of impacts and the protection of groundwater to ensure the long-term sustainability of the water supply in this SWA. SD is a methodology which also enables environmental analysis, focusing on the progression of environmental impacts over time. The models can be informed by environmental analysis techniques, such as Environmental Impact Assessments (EIAs), to establish a better understanding and analysis of the risks associated with mining in this area. The methodology also allows for various scenarios to be assessed, which could include the impacts of introducing new mitigation interventions to reduce the potential groundwater contamination risks. Therefore, analysing the impacts of land uses, such as mining, on hydrology within a catchment area contributes to effective watershed management strategies, water resources planning, and water conservation measures [12].

Introduction to the Blyde River Catchment, a Strategic Water Area of South Africa
The study area is the Blyde River Catchment (BRC), which is a sub-catchment of the Olifants River Catchment/basin of the Olifants Water Management Area (OWMA) (see Figure 1A,B). The study area comprises the B60A-D quaternary (hydrological) catchments, as determined by the South African Department of Water and Sanitation( Figure 1C) [13]. In this study, SD modelling is used to understand and represent the interaction between mining operations and the surrounding environment, simulating the dynamic behaviour of environmental risks that may arise from mining within the BRC and the impacts of these risks on groundwater resources. The concern for groundwater quality in this region is because it is envisaged that the BRC will be able to provide good quality water of sufficient quantity to the Olifants River Catchment (ORC).
A reconciliation strategy (and associated studies) is a means of reconciling current (and projected future) water deficits in a catchment. The latest reconciliation strategy for the ORC was published in September 2015, which updated an earlier reconciliation study undertaken between 2009-2011 [14], which had recognised that interventions were required to reconcile the available supply. The strategy proposed eight interventions that were divided into two broad categories: (1) interventions aimed at reducing water requirements; and (2) interventions aimed at increasing system yield. Out of the eight interventions, developing groundwater is the single largest proposed intervention (with a potential yield of 70 million m 3 per year (mcm/year)). The protection of groundwater-both from contamination and any additional abstraction-is therefore critical for the functionality of the catchment [15]. The most recent study which looked at the feasibility of developing groundwater resources by utilising the Malmani subgroup dolomites indicated that the groundwater potential contribution could be 39.5 mcm/year [16]. This is 30.5 mcm/year less than what was initially estimated, leaving the reconciliation strategy with a significant shortfall. There are also a number of concerns surrounding the cost of moving this water to the areas that need it. While groundwater development is feasible, it is not as significant a resource as was expected and will come at a great expense [13]. This highlights the need to keep the available groundwater as free from pollution as possible.

The Potential Impacts of Mining on Groundwater Resources
Gold mining contributes to both the decline in water quality and quantity through sulphide contamination from mine wastewater. The impacts of mining on water quality are dependent on the mineralogy and geochemistry of the mined ore body. These impacts have been investigated through research and the requirements for EIAs in mine operations [17]. Mining can affect water quality in various stages of the mine's life, including ore mining, processing, mine closure, and post-mine closure. Mine excavation exposes rock material to oxygen and water which results in the increase in oxidation, weathering rates, and the mobilisation of potential pollutants such as toxic metals and solutes like sulphides and arsenic [18]. Pollutants seep into the freshwater environment from waste rock dumps, tailings storage, and walls of mine shafts contribute to contamination of local and regional water supplies [17]. In this study, the processing of the hard rock material takes place at the existing Pilgrims Rest region's metallurgical plant with tailings facilities, which results in acid leaching [19]. There are two common interventions which are used to minimise the risk of pollution to the groundwater; these include the recycling of wastewater, the inclusion of treatment plants and possible neutralisation approaches, and the lining of the tailing dams. Traditionally, tailings dams are lined with clay, but synthetic liners are being used more frequently when new tailings dams are being constructed [20].
This paper demonstrates the value of using systems dynamics modelling to analyse the feedbacks and interconnections between mining and the broader environment and assess the feasibility of various interventions to mitigate the impact of mining, with a particular focus on the impact of mining activities on groundwater.

System Dynamics Modelling Approach
System dynamics (SD) is the understanding of the relationship between integrated systems elements and how they impact each other's behaviour [21]. The integration of systems elements is done by the incorporation of concepts such as stocks, flows, feedbacks, and delays, enabling the analysis of the dynamic behaviour of the system elements over time [22]. The approach is used to describe, model, simulate, and analyse complex systems with multiple interacting elements in terms of processes, information, organisational boundaries, and strategies [23]. The state of water resources (such as reduced flows, water insecurity, or low water availability in a catchment) cannot be attributed to one factor; instead, the state of water resources is a result of complex interactions of socio-economic, ecological, and political factors [21,24,25]. The SD approach is a technique that can be used in investigating and managing the complexity of hydrological, natural, environmental, and social domains [26]. Hence, the adoption of a systems philosophy in water resources development can enable water conservation, sustainable water use, and water resources protection through analysing, investigating, and supporting the decision-making processes in water systems [26]. The overall use of system dynamics as a form of quantitative policy analysis is increasing within the international water sector, especially in the research areas of regional planning, river basin management, flooding, and irrigation [24,25,27,28]. The use of system dynamics modelling has also been growing within South Africa more broadly [29] and in the use of the approach in the water sector, more specifically [24,30].

The Causal Loop Diagram (CLD) of the Problem Conceptualisation
The causal loop diagram (CLD) analytical tool used to represent the relationship between systems variables and dynamic feedback structures was constructed using Vensim modelling software (Ventana Systems Inc. 60 Jacob Gates Road Harvard, MA, 01451, USA, http://www.ventanasystems.com/). The overall structure of the CLD (Figure 2) represents the links between water use in gold mining operations and the broader water resource system. Mining operations require water, which is abstracted from the adjacent streams of the BRC, resulting in a decrease in the volume of water available within the river system. The decrease in the available water in the river is exacerbated by climate change and the ability of the river to supply water to water users downstream during drought events. showing the overall problem conceptualisation and the system boundary. Arrows connect two or more variables of interest and are causal links that run in the stated direction. '+' = a positive relationship, indicating that the causality runs in the same direction (i.e., an increase in variable A will cause an increase in variable B and vice versa); '-' = a negative relationship, indicating that the causality runs in the opposite direction (i.e., an increase in variable A will cause a decrease in variable B and vice versa). The variables connected by the thin green arrows pertain to surface water management and are conceptually included in the rationale for groundwater resource development, but surface water is not empirically modelled in the simulation model. The balancing feedback loops are numbered Bn and labelled. The variables in red font with black arrows show select intervention points in the system. BRC = Blyde River Canyon; GW = groundwater.
The top half of the CLD in Figure 2 introduces impacts of gold mining activities in the BRC, depicting the interaction between mining water use, wastewater and potential pollution, and the associated risks of contamination. Therefore, 'unexploited gold' in the BRC drives the 'mining activity' (gold ore excavation and gold processing) in the region. Mining activity results in 'mined gold' which, in turn, depletes the unexploited gold reserves, forming the gold mining balancing feedback loop (B1). The mine wastewater production balancing loop (B2) represents toxic wastewater production from mining. The oxygenation of sulphide minerals such as pyrite through mining activity can increase contamination concentrations in local water resources. The wastewater in the tailings dams drives a decline in BRC water quality, which drives the potential water reduction, re-use, and recycling. Hence, this can be mitigated by processes that can either reduce the toxicity or reduce the quantity of wastewater generated in the mine. Toxic wastewater increases the potential for groundwater contamination. Contaminant levels are supposed to be managed within nationally recommended contaminant limits. When the actual contaminant levels are higher than these limits, then a gap forms. Closing this gap, either proactively or in response to government-enforced compliance, would serve to reduce the fraction of mining pollution potentially impacting the groundwater in the region, forming the third balancing feedback loop (B3).
Water availability in the Lower Olifants is reduced when the surface water availability in the BRC is reduced by water demands from mining being met. Water availability in the lower Olifants, downstream of the Blyde, is also impacted by the overall drivers, both natural and anthropogenic, that impact water availability in the Olifants River Catchment. In the Olifants River Catchment, this situation has led to the demand for groundwater in the BRC to grow. Increased groundwater demand combines with mining-driven pollutants to increase the overall probability of polluted groundwater impacting human health and the environment. The demand for groundwater increases the 'exploitation rate', reducing the 'groundwater stock' unless the exploitation rate is carefully managed in relation to the 'recharge rate' (see Table 1 for relevant rates). The quantity of groundwater in the groundwater stock impacts the dispersion of pollutants, affecting the lifetime of pollutants in the water body. The less the groundwater stock, the lower the dispersion rates, and the higher the number of pollutants in the groundwater.

. Model Specifications and Settings
The model was built in Stella Architect (v.1.9), dedicated system dynamics software developed by iSee Systems©. The model time horizon is a 40-year yearly interval from 2000 to 2040, which accounts for the planned mining period from 2009 onwards whilst allowing for an initial nine years for model calibration purposes. A quarterly delta time (DT) was selected. The DT of 0.25 resulted in a total of 160 time-steps (40 years × 4 time-steps/year), which is well within the established best practice in the SD domain of aiming for a total of <10 3 time-steps [22] and yet a sufficient number of time-steps to simulate the desired reference mode behaviour. For the evaluation of the differential equations, the Euler integration method was chosen over Runge-Kutta 2 or 4 (RK2 or RK4). Euler integration was deemed sufficiently precise given the combination of functions used in the model and the content of the model. Note that the choice of DT, time-step, and integration method were all tested as part of the model verification and validation procedures (see Section 2.4).
The next four sub-sections describe the structure of the simulation model with reference to the model's stock-flow diagrams (SFDs). The model structure presented here was developed through the standard SD modelling process of iterating between stages of conceptualising the problem, formulating the model, and running simulations [22,31]. The SFDs represent the accumulation levels in which the integration functions are calculated. The flows in the model structure provide channels of input and output to, and from, the stocks, representing the environmental and technical parameters that influence the accumulation and the depletion of the stocks. The model is described by a sub-model, with a narrative explanation and key equation formulations accompanying the SFDs. A summary table is provided at the end of the model description that details important model parameters and the associated sources of data (see Table 2).

Gold Mining Sub-Model
The mining sub-model is the representation of the mining process that occurs in the Sabie and Pilgrim's Rest region (see Figure 3). The mining process is explained in the mining plan from the Transvaal Gold Mining Estate (TMGE) competent person's report and the mining plan [19]. The mining project is planned to mine a total resource estimate of 25,280,000 tonnes in the Sabie and Pilgrim's Rest regions over the 40-year period in the 13 mines being studied. The mining sub-model, shown in Figure 3, is a mining chain with four stocks, starting from unexploited gold, which is a limited reserve. This represents the gold mining process in the mine operation. The unexploited gold stock is depleted by the yearly gold mining rate as a function of the total annual gold mined variable. This flows into the exploited gold ore stock which is, in turn, depleted by the gold processing flow that takes place at a gold processing rate, which is a function of processing plant capacity and the fraction of ore processed. This rate influences the accumulation in the third stock in the chain (namely, the gold ore being processed stock) before flowing into the recovered gold stock [19,32,33].

Wastewater Management and Seepage Sub-Model
The wastewater component of this sub-model represents wastewater produced in the mining process (see Figure 4). The model is built with the assumption that wastewater produced during mining and processing is discharged into the tailing dams. This submodel is based on the amount of water produced per tonne of ore mined during the mining stage and the amount of wastewater discharged from the processing stage of the mining sub-model, which is the total wastewater generated (TWG) (see Figure 3). The Wastewater in clay-lined dams (WWD) stock represents the total amount of water produced and discharged into the tailing dams. The flow of wastewater (WW) into clay-lined dams (r WWC ) represents the amount of wastewater produced from mining and gold processing that is discharged into the tailing dam. This flow represents the inflow of wastewater from the mine operation into the stock, and the outflow in this stock is represented by seepage from clay-lined dams (r S ). Seepage control by clay-lined tailing dams, which is the standard practice, is shown in the second main part of the sub-model shown in Figure 4. Clay lining has high permeability relative to the synthetic dam liners, which is an intervention aimed to reduce seepage in the tailings dam that is tested in the model (the full model equations for this intervention are detailed in Table S2). The mitigation intervention is onset by the switch to synthetic-liner tailing dams variable (sw synth ). Therefore, sw synth is equal to zero when the syntheticliner is not implemented, and the switch is equal to 1 when this mitigation measure is implemented hence reducing permeability in the tailings dam. Whether any wastewater flows into the stock of wastewater in synthetic-lined tailings dams is determined by the inflow of wastewater into synthetic-lined dams (r wws ), as per Equation (1): Potential seepage chemistry in the mine area was determined through leach testing of the goldfields in Sabie and Pilgrim's Rest regions, as reported in Rudzani et al. [34]. The results concluded that the sulphide concentration is the highest contaminant concentration in tailing wastewater in this region. Hence, the contaminant concentration in the model is based on the sulphate concentration in addition to the pollution plume simulation done in this area. Sulphide concentration is used as the indicator pollutant in the plume due to the high sulphate concentrations measured in groundwater near the tailings dams [34].

Neutralising Plant Sub-Model
Sulphate loads can be reduced via neutralising processes managed through a treatment plant, which is simulated via the model structure shown in Figure 5. The variable wastewater treated (WWT) is calculated using the quantity of wastewater requiring treatment (WRT), which is equal to the total wastewater generated (TWG) (see Figure 3), and the annual treatment capacity (ATC) according to the logic in Equation (2):  Wastewater produced per tonne gold mined 1 × 10 −6 mcm/t Amount of wastewater generated in mining. This is an assumption based on an estimated amount of dewatering done in a typical mine shaft Wastewater generated per tonne gold processed 6.893 × 10 −8 mcm/t Amount of wastewater generated in gold processing. The data for the amount of water processed is derived from the research done by Acheampong et al. [35] on the treatment plant of similar characteristic as the plant that will be used in the TGME mine project [35] (p. 3800).
Wastewater recycling 0.25 % Calculated against benchmarks used by the South African national Department of Water and Sanitation (DWS) in their report for water demand management in mining in South Africa (SA) ( Max tailing dam size 100,000 m 2 This is the area of the tailings area. This is indicated in the mine plan and Environmental Impact Assessment (EIA) report for this mine project [19] Max tailings Capacity 40 Mcm This parameter is the proposed capacity of the tailing dam that be constructed on the mine site. This is indicated in the mine plan and EIA report for this mine project [33] [16].
SANS 241 limit 500 t/mcm This South African National Standard (SANS) no.241 is derived from the hydrogeological specialist report that formed part of the EIA report for TGME [33] (p. 50). The actual limit of 500 mg/L is converted from mg/L to t/mcm in order to maintain unit consistency.
The conditional IF THEN ELSE function in Equation (2) uses the ATC to constrain the quantity of wastewater treated WWT. The ATC is adjusted by a switch between treatment plant options (sw treat ) that either (a) leaves treatment capacity at zero; (b) activates a 2.5 megalitres per day (ML/d) capacity neutralising plant (Plnt1); or (c) activates a 5 megalitre per day (ML/d) capacity neutralising plant (Plnt2).
The ratio of how much wastewater is treated (WWT) over how much wastewater is required to be treated (WRT) drives the actual sulphide concentration. This is modelled via a simplistic effect based on the logic that a higher ratio of ( WWT WRT ) means that less wastewater is left untreated; when the ratio of ( WWT WRT ) is low, then more wastewater is left untreated. This logic establishes an inverse relationship between the ratio and its effect on sulphide concentration used to drive the actual sulphide concentration, which, in turn, affects the sulphide concentration of seepage into the groundwater.

Groundwater (GW) Sub-Model
Mining and groundwater resource development in the BRC are conflicting activities that require trade-offs. Mining activity carries the risk of groundwater contamination, which reduces the contribution to the groundwater resource in the Pilgrim's Rest region and, in turn, affects the overall supply strategy for the Olifants River Water Supply System (ORWSS). The groundwater sub-model (see Figure 6) represents the amount of groundwater in the Pilgrim's Rest region. The stock inflow is represented by the aquifer recharge rate which is the rate at which water accumulates in the aquifer (note that the actual variability in the recharge rate is excluded from the model), with an average recharge rate derived from the groundwater assessments reported in the South African national Department of Water and Sanitation (DWS) [13,16]. The stock is reduced by three outflows which account for the current groundwater use, the potential groundwater water use in the proposed water resource development project, and the aquifer discharge, which is the rate at which water moves through the region. The values used in the groundwater sub-model are derived from the DWS assessment summarised in Table 1.
The groundwater that is at risk of contamination from mining is quantified using a simple risk factor derived from how much groundwater is abstracted and the ratio of the seepage concentration over the South African National Standard (SANS) 241 limit [33]. The higher the ratio and the more groundwater that is abstracted, the greater the risk of groundwater contamination by gold mining posed to groundwater development in the region. This risk factor is used as an indicator within the exploratory model, as noted in the results section that follows.

Model Validation and Documentation
Following Groesser and Schwaninger [38], model validity is understood as 'the property a model has of adequately reflecting the system being modelled, contingent on model purpose' (p. 157). The model described here was subjected to multiple tests of model validity in accordance with the best practices recommended by Barlas [39], Rahmandad and Sterman [40], and Ford [22]. Table 3 outlines the six model validation tests employed in this study, divided into two test categories, with the associated purpose and requirements for passing each validation test listed alongside the specific tools and procedures employed in this study. Model parameters were adjusted (by +/−25% and +/−50%) and model behaviour was observed, checking for behaviour reproduction with changes only in amplitude.
Model documentation follows the best practices and guidelines stipulated by Rahmandad and Sterman [40] and Monks et al. [41]. The model itself is available on the iSee Exchange model repository (https://exchange.iseesystems.com/models/player/jai/brcsd-model) and all model settings, equations, and values are detailed in the Supplementary Materials (Tables S1 and S2), enabling full reproduction of the model and the results presented in this paper.

Testing and Comparing the Efficacy of Interventions
The simulation results of these interventions and scenarios are represented by time series graphs which aim to compare baseline conditions and the impact of mitigation intervention scenarios on groundwater contamination risk (see Table 4). The scenario of groundwater (GW) resource development in the Pilgrim's Rest region of the BRC is then simulated, with the efficiency of each of the four interventions tested under a scenario of groundwater resource development. Table 4. Description of simulation runs of intervention scenarios.

Intervention Description of Parameters
Baseline conditions (Base run) The baseline scenarios are simulated without mitigations to reduce the impact of GW contamination risk as a result of mining activity. Simulation results for the wastewater recycling intervention are presented in three time-series graphs in the composite Figure 7 below. Figure 7A shows the change in the annual flows of 'total wastewater generated', which is the sum of 'wastewater generated from gold mining' and 'wastewater generated from gold processing' (see Figure 3 and associated text for description of the model's structure). Intervention 1 WW recycling simulates a 25% reduction of the wastewater generated by gold mining and gold processing that is destined for the tailings storage dam (because 25% of the wastewater generated is recycled). The 25% reduction starts in 2021, decreasing the 'total wastewater generated' from 2.51 mcm/year in the Base run to 1.88 mcm/year. Figure 7B represents wastewater accumulation in the clay-lined tailings dams. Initially, the curve shows no difference, but in 2025, the difference between the Base run and the Int.1 is 2.6 mcm and increases to 4.3 mcm by 2030 (Base run = 32.5; Int.1 = 28.2 mcm). Figure 7C represents the ratio of seepage concentration compared to the SANS241 limit. The effects of the Base run are evident in 2033when the seepage concentration is 270% of the above the SANS241imit compared with 200% in the Int.1 run in which wastewater recycling is taking effect (showing a change of 70% in the seepage concentration).

Intervention 2 (Int.2) and Intervention 3 (Int.3): Testing Two Capacities of Wastewater Neutralisation Treatment Plants
Interventions 2 and 3 test two capacities of a wastewater neutralisation treatment plant (see Figure 8 for details). These interventions decrease the amount of wastewater produced in the mine operation. The treated wastewater is that amount of water discharged from the mine operation into tailings dams. Figure 8A shows the model behaviour of the variable 'annual treatment capacity' and Figure 8B,C compare the quantity of wastewater treated and the water left untreated, respectively. The simulation results depict the decrease in the amount of untreated wastewater generated in the mine. In Figure 8B, no wastewater is treated in the Base run. However, when the interventions are implemented, treated wastewater increases to 0.9125 mcm/year in Intervention 2 (Int.2) and to 1.825 mcm/year in Intervention 3 (Int.3) (see Figure 8B) with an associated decline in the quantity of wastewater left untreated (see Figure 8C). Figure 8D compares the rise in the sulphate load, calculated in t/year, that is generated by gold mining in the Pilgrim's Rest region, which is at risk of contaminating groundwater (GW). The sulphate load in the Base simulation keeps rising, stabilising at~5300 t/year by 2033 in the Base run compared to~3300 t/year in 2033 in both the Int.2 and Int.3 runs. Note that the difference between the resulting sulphate loads from the two capacities of treatment plants is minor.

Intervention 4 (Int.4): Minimising Seepage via a Synthetic-Lined Tailings Dam
Simulation results for minimising seepage intervention through synthetic lining are presented in four time-series graphs in the composite Figure 9, below. The fourth intervention simulates an intervention to reduce contamination of groundwater by directly reducing the seepage from new tailings dams that are lined with synthetic liners that have a lower permeability factor than the single clay-liners used as standard.  Figure 9A shows the result of this intervention (Int.4: synth. Lining) in terms of how the inflows into the clay-lined tailings dams grow until 2021 and then drop to zero from 2021 onward as all-new wastewater flows are redirected to the synthetic-lined tailings dams. Figure 9B compares the 'total seepage' across three runs, namely the Base run, the Int.1: WW recycle run, and the Int.4-synth. lining run. The highest quantity of seepage, in mcm/year, is in the Base run, and it is reduced by~10% in the Int.1 run with wastewater recycling. The lowest seepage (Line 3) is from Int.4, which shows declining total seepage from a high of 0.121mcm/year in 2021 down to 0.107 mcm/year in 2040. When comparing Figure 9C,D, it can be noted that the majority of the seepage continues to seep from the existing wastewater in the clay-lined tailings dams (line 3 in Figure 9C). Although the seepage quantity does grow from the synthetically lined tailings dams, (line 3 in Figure 9D), the scale is very different (around 1500 m 3 /year in Figure 9D versus around 100,000 m 3 /year in Figure 9C).

The Implication of Intervention Scenarios of Groundwater Resource Development
This sub-section presents the simulation results of the scenario of groundwater resource development (GW devp) in the Pilgrim's Rest region of the BRC, with the efficiency of each of the four interventions tested under a scenario of groundwater resource development. A total of six curves are represented with the final results presented in Figure 10. The second variable on the graph represents the quantity of groundwater at risk of contamination from the mine ('at risk GW'-line 2), based on the amount of water planned to be exploited in the well fields of Pilgrim's Rest region. Line 3 represents the 'GW contamination from mining risk factor', measured as a dimensionless index scaled out of 100 (the higher the risk factor, the more groundwater is at risk). The ratio is therefore a fraction of the amount of groundwater developed and the potential wastewater emanating from the gold mine facility as a result of seepage, hence the greater the amount of wastewater, the greater the contamination risk to groundwater developed in the region. The interventions aim to mitigate this risk by reducing the seepage of contaminants into the groundwater resources. Figure 10. The final comparison of scenarios of groundwater development in relation to the four interventions. The variable displayed is the cumulative 'GW contamination from mining risk factor', measured as a dimensionless index (dmnl) scaled out of 100 (the higher the risk factor, the more groundwater abstracted for the BRC is at risk). Note that the x-axis is shortened to only display the results from 2015-2040 in order to enhance the legibility of the results. Line 1 represents the base condition before groundwater development, hence indicating a low risk. An increase in groundwater risk is indicated in line 3 of Figure 10, which shows a simulated run of groundwater development combined with Intervention 1: wastewater recycling [GW devp + Int.1 WW]. Line 3 run shows that if groundwater development occurs and wastewater recycling begins, then the maximum risk factor drops from~92/100 to~67/100 for the last five years of the simulation period The most effective intervention that reduces the GW risk factor is Intervention 4: synthetically lined tailings dams, shown in Line 6 and simulation run [GW devp + Int.4-synth] in Figure 10. In this scenario in which GW development is occurring alongside the lining intervention, the peak risk factor is 18.8/100 in 2030 and is reduced to 16.3/100 in 2040. The building of new synthetically lined tailings dams would be both costly and would be subject to required environmental planning approval. For this reason, it is more likely that multiple other interventions that are less resource and bureaucracy-intensive would be combined. One such combination is presented in the seventh simulation run (line 7 of Figure 10), which presents the results of groundwater resource development together with two other interventions (GW devp + Int.1 + Int.2). The combination of wastewater recycling (Int.1) and the smaller treatment plant (Int.2) gives a risk factor of~42/100 for 2032-2040.

Discussion and Conclusions
The South African Water Act of 1998 [42] was ground-breaking legislation and is often hailed globally as being rigorous and fair. Water is a limiting resource in South Africa, and it is currently fully allocated across the various sectors including maintaining the ecological reserve. Any additional use in the future would mean redistribution across the sectors, therefore it is imperative that water is used wisely and complies with the concepts of sustainable development. Strategic water areas substantially contribute to the economy by sustaining water for people, industry, and most importantly, the natural environment. Strategic water areas (SWAs) provide a disproportionate amount of water to the system relative to their size and therefore require careful management that should be driven by evidence on the various trade-offs of land and water use. This paper analysed the environmental risks of gold mining on water resources in the BRC over time, focusing on the groundwater resources in the upper reaches of the BRC by developing a systems perspective of the activities. The process of systems analysis and system dynamics (SD) modelling acknowledges the complex nature of water resources. The complex nature of the South African water sector and the value of systems thinking and modelling in achieving sustainable water resource management have been noted by multiple authors (e.g., [24,43,44]). The establishment of conflicting activities such as mining and groundwater development in the Pilgrim's Rest region creates a complex situation in which multiple developmental goals are in tension, namely, gold mining, with the associated socio-economic and financial benefits, environmental impacts, and groundwater development, which requires good-quality groundwater of a sufficient quantity in order to meet the requirements.
In this research, SD modelling was used to analyse the impacts identified in Environmental Impact Assessments (EIAs) commissioned by the Transvaal Gold Mining Estate (TGME), the company which used to own the mining rights in the region. As noted by Lagnika et al. [23], although mining companies identify environmental risks and formulate mitigation measures in their EIAs and environmental management plans, environmental impacts typically persist during and after the mine operations. Hence, despite the cau-tionary measures made during mine planning, environmental impacts still occur before operations, and this puts the BRC at risk of a decrease in water quantity and quality. The modelling was undertaken with the assumption that the mining production will take place as indicated in the mine production plans. The planned timeframe is used in the model to simulate the effect of mining as planned. The model does not account for possible delays or challenges that might hinder the establishment of the mines. The baseline analysis depicts the annual tonnage, for the 13 mines, over the full simulation period from 2000 to 2040. The mining operations will take place at different times with an average yearly tonnage of 240,000 tonnes per mine from a total resource estimate of 25.28 million tons of gold-bearing ore. These are hypothetical predictions of trends that act as a reference point for change in the system and how scenarios of intervention and mitigation can change the behaviour of the system over time. The model runs show that the activities of the mining operations peak between 2022 and 2025, and yet the contamination levels and the sulphate loading peak in 2040, the last year of the simulation. The mitigation measures identified in the TGME mine's EIA report were meant to protect and reduce the impacts on groundwater resources and to achieve environmental protection during the mine lifecycle [19,32,33]. All mitigation measure interventions show a lag time in the order of 10-13 years before the risk of groundwater contamination starts reducing. Two indicators are used to show this lag time: firstly, the sulphate load that is at risk of contaminating groundwater (GW), measured in t/year, and secondly, the ratio of seepage concentration to the SANS241 limit set for potable water, measured as a dimensionless ratio. In synthesis, the recycling wastewater intervention scenario shows that the highest sulphate load of 4500 t/year occurs in 2040, followed by the treatment plant intervention which has sulphate load of 3250 t/year. In the period between 2021 and 2029, the full capacity of the 5 ML/d treatment plant is utilised, which is reflected in the lower sulphate load (3100 t/year vs. 3600 t/year). It is noteworthy that after 2029, the 2.5 ML/d and the 5 ML/d plants have the same effect on sulphate load and the ratio of seepage concentration to SANS241 limit, reflecting the fact that the quantity of wastewater requiring treatment can be met by the smaller-sized plant for the majority of the simulation period. The intervention most effective in lowering the sulphate load stemming from mining in the Pilgrim's Rest region and therefore reducing the risk to groundwater is the development and use of synthetic-lined tailings dams.
The final section of the results clearly shows that groundwater is at risk of contamination. The different runs of the scenarios with the component of groundwater development introduced using stepped increases that begin in 2022 until 2040 shows how the groundwater contamination risk factor increases along with the stepped groundwater development. A worst-case scenario, with no mitigation measures, shows rapid contamination, however, it is unlikely to be the case. As discussed in the previous sections, some of the mitigations cannot be introduced due to cost and feasibility. For this reason, it is more likely that multiple other interventions that are less resource and bureaucracy-intensive would be combined, the scenario run that was most promising showed that the combination of wastewater recycling and the smaller treatment plant (Int.2) gives a result of a risk factor of~42/100 for 2032-2040. The Pilgrim's Rest region of the BRC can potentially supply critical quantities of groundwater of good quality through the proposed groundwater development project. An overall catchment hydrological study is needed, particularly in the light of climate change. Whilst the eastern parts of South Africa are expected to receive approximately the same amounts of total annual rainfall, droughts and extreme events will be more frequent, markedly impacting the variability associated with the hydrological cycle and the recharge of aquifers [45]. One of the limitations of this study is that the focus of the model is on groundwater impacts and excludes both surface water dynamics and the dynamics of interflow between surface and groundwater. The reconciliation strategy for the Olifants River Catchment (ORC) published in 2015, showed that interventions were necessary to meet the gap between supply and demand [14]. It was suggested that groundwater development had a potential of 70 mcm/year with the expectation that it would mostly be sourced from the Malmani subgroup dolomites which indicated that the groundwater potential contribution only could be 39.5 mcm/year [16]. This is 30 mcm/year less than what was initially estimated, leaving the reconciliation strategy with a significant shortfall. Therefore, the protection of the groundwater from contamination and any additional abstraction is critical for the functionality of the Olifants River Water Supply System (ORWSS).
According to work done by Le Maitre et al. [8] on the 'Identification, Delineation and Importance of the Strategic Water Source Areas of South Africa, Lesotho and Swaziland for Surface Water and Groundwater', poor groundwater quality is often used as motivation to not use the resource. This can potentially compromise the use of SWA groundwater to augment water supply at a larger scale for the Olifants Water Management Area (OWMA). The simulation results reveal that mining activity in the BRC can potentially have adverse effects on water quality, driven by a range of mining-related activities, including particular types of mining, discharges of pollutants, and malfunctioning wastewater treatment plants. These impacts must be managed effectively, properly assessed through compliance monitoring, and mitigated and restricted in cases where water resource protection is not achieved. The potential for groundwater contamination is exacerbated by the fact that the well-field target zones in the Pilgrim's Rest region occur in the same area as TGME gold mines. The 'Feasibility Plan for Groundwater Resource Development of the Malmani Dolomites within the Olifants River Water Supply System' emphasises the significance of ensuring that the aquifers in the well-field target zones in the Pilgrim's Rest region sustain their integrity [16]. Le Maitre et al. [8] investigated the susceptibility of South Africa's aquifers, and these were mapped nationally as groundwater vulnerability, separated into categories ranging from very low to very high. The aquifers in BRC have high vulnerability; hence aquifer protection is a priority during the implementation of the ongoing gold mining in the Sabie and Pilgrim's Rest regions. A key recommendation in the 'Feasibility Plan' is to develop an aquifer protection plan to support sustainable groundwater abstraction from the region. The feedbacks and interconnections between mining and the broader environment demonstrate why systems analysis is required for any protection plan. This paper demonstrates the value of using systems dynamics modelling to analyse the problem and assess the feasibility of various interventions. Sustaining high-quality water in catchments is critical for the well-being of many South Africans as well as maintaining the proud history of the mining industry in the country.

Conflicts of Interest:
The authors declare no conflict of interest.