Hydropower Generation Through Pump as Turbine: Experimental Study and Potential Application to Small-Scale WDN

Pump-As-Turbine (PAT) technology is a smart solution to produce energy in a sustainable way at small scale, e.g., through its exploitation in classical Water Distribution Networks (WDNs). PAT application may actually represent a suitable solution to obtain both pressure regulation and electrical energy production. This technology enables one to significantly reduce both design and maintenance costs if compared to traditional turbine applications. In this work, the potential hydropower generation was evaluated through laboratory tests focused on the characterization of a pump working in reverse mode, i.e., as a PAT. Both hydrodynamic (pressure and discharge) and mechanical (rotational speed and torque) conditions were varied during the tests, with the aim to identify the most efficient PAT configurations and provide useful hints for possible real-world applications. The experimental findings confirm the good performances of the PAT system, especially when rotational speed and water demand are, respectively, larger than 850 rpm and 8 L/s, thus leading to efficiencies greater than 50%. Such findings were applied to a small municipality, where daily distribution of pressure and discharge were recorded upstream of the local WDN, where a Pressure Reducing Valve (PRV) is installed. Under the hypothesis of PRV replacement with the tested PAT, three different scenarios were studied, based on the mean recorded water demand and each characterized by specific values of PAT rotational speed. The best performances were observed for the largest tested speeds (1050 and 1250 rpm), which lead to pressure drops smaller than those actually due to the PRV, thus guaranteeing the minimum pressure for users, but also to mechanical powers smaller than 100 W. When a larger mean water demand is assumed, much better performances are reached, especially for large speeds (1250 rpm) that lead to mechanical powers larger than 1 kW combined to head drops a bit larger than those observed using the PRV. A suitable design is thus fundamental for the real-world PAT application.


Introduction
Nowadays, the need to produce energy in a sustainable way is an important issue to tackle to both improve environment quality and human life. To this effort, new energy systems, exploiting different available natural sources such as water, have been developed over time to reduce carbon emissions and produce energy in a renewable way (e.g., [1][2][3][4][5][6][7]). One of the main and first sources used to obtain clean energy is water, since the huge availability of hydraulic resources, which can be exploited in in terms of both head drop and flow rate. In the ER approach, an inverter is required to change the rotational speed of the PAT, leading to the speed that optimizes the PAT working conditions. The Variable Operating Strategy (VOS) is a suitable methodology which allows one to select the PAT for a specific WDN when either the HR or the ER approach is used [2,22]. The VOS mainly consists in the analysis of the required backpressure and available head, in addition to the estimate of the overall plant efficiency during a considered operational time range, such efficiency also depending on the rotational speed in the ER case [22]. A series of available PATs with known characteristics must be analyzed, with that providing the largest efficiency being the best solution. The hydraulic and electric regulation (HER) is a further method coming from the combination of the previous approaches, and consisting in the optimal regulation of the PAT using the valves of the HR approach and the inverter of the ER approach. For a complete overview, some authors expressly address the issue of the economic feasibility of the systems, considering the additional investment and maintenance costs, compared to provided energy benefits [24,25].
The motivation of the present study is mainly due to the fact that only some literature works investigate the possible use of a PAT in place of or in parallel to a PRV which regulates the pressure of an existing WDN [26,27]. Few works deal with the possibility to improve the PAT operation by adjusting the PAT rotational speed [6,28]. To the authors' knowledge, there is a lack in the literature about a possible PAT application to the WDN of a small municipality (fewer than 5000 people), as well as about the investigation of the PAT performances when different values of mean water demand and rotational speed are used.
The present work is part of a collaborative project, named Water In Sustainable and Efficient Buildings ("WISE Buildings"), which aims at finding an appropriate and efficient solution to produce energy from the water source in different urban contexts and at different scales (e.g., building or neighborhood), also considering related life-cycle environmental impacts and costs. This could be obtained by exploiting PAT technologies in water supply systems, which could be particularly suitable for areas where a large part of unexploited energy is often present, due to the excess water pressure to dissipate [25]. Specifically, such approach may be extended and, more efficiently, applied to the case of remote villages or decentralized districts where an important amount of excess water pressure is likely to occur. Such areas may benefit of a PAT-based system, i.e., a micro-or pico-hydropower plant, able to provide both pressure dissipation and energy production. Hence, one of the goals of the present project is that of studying the functioning of a pump working as a turbine installed within a portion of a typical WDN.
As the first step of the above project, an experimental investigation was conducted at the Università Politecnica delle Marche (Ancona, Italy), testing a centrifugal pump installed in a laboratory facility. Different regimes were tested: the hydrodynamic conditions, i.e., pressure and discharge, were varied to reproduce the classical performance curve; in addition, a test bench enabled us to regulate the mechanical conditions, i.e., both rounds and torque of the PAT shaft. Such tests allowed us to mimic typical conditions experienced in real applications and to estimate the actual energy production.
Within the framework of the "WISE Buildings" project, the main findings of laboratory tests will be related to PAT-application scenarios in real urban contexts where water demand profiles are set, with the final goal to assess their life-cycle costs and environmental performance based on the energy produced. On the other hand, the main objectives of the present study were: (i) characterization of the PAT functioning; (ii) simulation of possible PAT application to the WDN of a small municipality; and (iii) analysis of different real-world scenarios using available field data and laboratory findings.
The manuscript is divided as follows. Section 2 describes both experimental tests and application to a real-world context. Section 3 describes and discusses the main results of the work. Some conclusions close the paper (Section 4).

Experimental Tests
Energy generation from domestic and urban water supply systems was tackled by exploiting an experimental facility available in the Laboratory of Hydraulics and Maritime Constructions of the Università Politecnica delle Marche (Ancona, Italy). The facility has been equipped with a centrifugal pump (Rotos pump, Aturia group), which was used in the past in the classical mode for a different laboratory purpose. This was recovered for the present work and used as a PAT, i.e., in reverse mode. When working in classical mode, the pump is characterized by a nominal power of 1.23 kW, while the maximum head and flow rate are 12 m and 11.12 L/s, respectively. The main characteristics are listed in Table 1, while a top view of the system is illustrated in Figure 1.  To regulate the hydrodynamic field, a feed pump, two flowmeters, and three pressure gauges were mounted on the supply system. This was characterized by PVC pipes with diameters DN110, DN75 and DN50, in agreement with both typical WDN pipes and PAT inlet/outlet ( Figure 2a). Specifically, an auxiliary 5.5 kW pump (Caprari multistage vertical electric pump) was used to supply water from the tank to the PAT at desired head and flow rate. An inverter was also used to select the operation frequency of the feed pump within the range 35-50 Hz. The discharge traveling through the PAT was measured using two sensors: an electromagnetic device located just downstream of the feed pump (Endress+Hauser, Promag 10) and an instant measuring flowmeter located more downstream in the supply system (Riels Instruments, FPL Series). To measure the pressure drop between upstream and downstream of the PAT, a manometer and two pressure sensors (Endress+Hauser, Cerabar PMP21) were used. In addition, a set of pressure taps was also installed to investigate the pressure values at 6 different locations around the PAT: 1 upstream of the PAT, 4 around the pipe circumference just downstream of the PAT, and 1 about 1.7 m downstream of the PAT exit (Figure 2a,b). The equipment used in the present experiment is summarized in Table 2.  In addition to what is presented above, a bypass pipe was also included in the model, together with four regulating valves, named V1, V2, V3, and Vu ( Figure 2a). Opening of all valves allows the water to flow within the whole system, closure of V1 inhibits the flow to pass through the bypass, while closure of V2 and V3 excludes the PAT-system portion. Hence, such approach allows the user to simulate the PAT application in typical WDNs, as well as to properly adjust both water head and flow rate affecting the PAT. A transparent PVC pipe was installed downstream of the PAT to visualize the vorticity generation at the PAT exit, due to turbulence and cavitation occurring at specific regimes ( Figure 2b). The pressure measurements around the pipe circumference just downstream of the PAT exit were used to investigate the pressure variations induced by such vorticity.
To properly characterize the PAT behavior, a test bench was exploited with the aim to regulate the PAT motion by exerting a braking force on its shaft. This enables one to measure the output power, the torque and the speed (rounds per minute) induced by the water flowing within the PAT when subjected to different heads. The test bench (Borghi&Saveri) was coupled to the PAT and integrated into the supply system ( Figure 2a). Hence, adjustments of both test-bench brake and regulating valves allowed the analysis of various working configurations, with multiple combinations of hydrodynamic and mechanical actions characterizing the PAT.
The main goals were those of determining the performance characteristic curve, the efficiency, and the produced power of the PAT under the above working conditions. As for the classical turbines, the hydraulic power of the flow traveling through the PAT blades P H is converted into mechanical shaft power P M . The hydraulic power is defined as with γ the water specific weight, Q the discharge, and ∆H the head drop calculated between upstream and downstream of the PAT. The mechanical power is with M the torque and N the rotational speed of the PAT shaft. The PAT efficiency is the ratio between mechanical and hydraulic power Finally, the mechanical power could be further converted into electricity by means of a generator [29]. During the experimental tests, the feed pump, located in the upstream part of the plant, enabled us to vary the flow discharge in the range Q = 5-9 L/s, while the available pressure head was H = 4.8-33.9 m. Two different series were conducted.

•
Test Series 1: Both rotational PAT speed N and inverter frequency were kept constant during each test, the former imposed at the test bench, the latter at the feed pump. From test to test, the speed varied in the range N = 650-2350 rpm, while the frequency ranging 35-50 Hz, with step of 5 Hz. • Test Series 2: N, inverter frequency, and discharge Q were kept constant during each test. Such test series was conducted (i) imposing the rotational speed at the test bench; (ii) fixing the feed-pump frequency; and (iii) regulating the valves. This enabled us to have the same flow-rate values, ranging within Q = 5-9 L/s, for each tested speed, this ranging N = 650-1250 rpm.

Application
With the aim to investigate a possible application of the PAT system studied in the present work, some data collected in the municipality of Servigliano (Fermo, Italy) were used. Here, pressure dissipation was provided through a PRV located upstream of the WDN. Two diverse datasets are available. The first concerns water-volume data collected by the local water authority between 2007 and 2013, and provides the daily mean water consumption in Servigliano, as illustrated in Figure 3 (blue dots). Specifically, the water demand ranges between 2.75 and 5.27 L/s in the analyzed time period. The summertime data are highlighted in red, while the maximum data available in the time series, corresponding to ∼10% of the data in the whole investigated period, are shown in green. The second dataset refers to a specific day, i.e., 17 July 2008. In this case, data were collected continuously by a gauge located just downstream of the reservoir which feeds the whole municipality. Figure 4 illustrates the hourly distribution of the flow rate (blue solid line), which is characterized by a double peak corresponding to the times of larger demand, i.e., around 8-9 and 20-21. The demand ranges between a minimum discharge Q min = 1.24 L/s during the nighttime and a maximum discharge Q max = 5.28 L/s in the morning. The mean water demand of such day is thus µ q = 3.72 L/s, which is in agreement with the average value estimated from the data collected between 2007 and 2013, i.e., µ q = 3.70 L/s (dashed line in Figure 3). The ratio between the hourly demand and the mean demand provides the hourly coefficient: whose distribution for the considered municipality is illustrated in Figure 4 (blue dashed line). Such trend is typical of relatively small urban areas. Specifically, while areas with larger population (over 10, 000 people) are identified by C d distributions characterized by a smoothed trend and only one peak [30][31][32], smaller areas are identified by two ore more peaks (e.g., [33]). The classical law used to estimate the daily mean water demand is where α is the ratio between the daily mean water demand and the annual mean consumption, n is the population, and d is the per capita water demand. For the specific case of Servigliano, the population in 2008 was n = 2377 (available online: https://www.tuttitalia.it/marche/81-servigliano/statistiche/ popolazione-andamento-demografico/, accessed on 8 May 2012) and it can be assumed d = 130 lpd (suitable for urban areas with n < 5000 [30]). Since the mean water demand is known, the coefficient is calculated from Equation (5) and is found to be α = 1.04. This is smaller than the daily peak factor (α p = 1.3 for small urban areas), which represents the day of maximum consumption during the year.
In addition to the above-described scenario, another scenario was built on the basis of the flow-rate range investigated in the laboratory. With this purpose, a daily mean water demand µ q = 7.50 L/s was tested, this value being far larger than the daily water demand referring to the summertime period ( µ q summer = 4.24 L/s, red circles in Figure 3) or the 10% largest values ( µ q max = 4.66 L/s, green circles in Figure 3). Under the hypothesis that the same water demand d and α coefficient of Servigliano are used, such scenario can be seen as referring to a population slightly smaller than 5000. In this condition, the use of the C d distribution illustrated in Figure 4 can still be retained as valid.
To summarize the scenarios introduced here and analyzed in the next sections, Table 3 reports the main features. The combined use of the selected µ q with the C d distribution enables one to calculate the water-demand evolution. This is represented in Figure 4 for Case 1 (blue solid line) and Case 2 (orange line). It is worth noting that the water demand of Case 1 is generally smaller than the flow rate leading to the best PAT performances, while that of Case 2 is in good agreement with the experimental range.

Results
The following sections describe the main findings from the experimental tests carried out at the Università Politecnica delle Marche (Sections 3.1 and 3.2) and their application to the real-world contexts (Section 3.3). To better understand the error propagation due to the instrument accuracy (see Table 2), error bars are also illustrated in the next figures (for details, see also [6,34]).

Hydraulic Properties
The characteristic curve of the pump working in direct mode was available for the rotational speed N = 1450 rpm and is represented in Figure 5 (dashed black line). Conversely, the characteristic curves for the pump working in reverse mode were not available. Hence, the first aim of the experimental tests was that of finding such curves, which represent the evolution of the head drop ∆H with the discharge Q at specific rotational speeds, imposed through the test bench.
The PAT curves resulting from Test Series 2 are shown in Figure 5 (dashed colored lines). Each curve refers to a specific speed N: the flow rate increases with ∆H when the pump works in reverse mode (solid lines). With Q fixed, larger rotational speeds provide larger head drops. Such behavior is more pronounced at smaller Q values and reduces at higher Q. Hence, the smaller is N, the larger is the curve steepness, which means that an increase of Q provides larger increases of ∆H at smaller N values. With the aim to understand the error related to the hydraulic properties, both horizontal and vertical error bars are illustrated in Figure 5, showing a significantly small error of both Q (order of 10 −2 L/s) and ∆H (order of 10 −2 m). Each experimental dataset related to a specific speed was interpolated using a second-degree polynomial function, with the aim to correlate Q, ∆H and N (dotted colored lines).

Mechanical Properties
Flow rates passing through the PAT increase with the increase of the feed-pump frequency, although such quantities are not proportional. Specifically, a fixed feed-pump frequency leads to larger/smaller Q values (hence to larger/smaller ∆H) for smaller/larger values of the PAT rotational speed N (e.g., a 45 Hz frequency provides Q ranging from 7.2 to 5.8 L/s when the speed N changes from 650 to 2200 rpm). With the purpose to investigate the mechanical PAT behavior, results of Test Series 1 are here reported. The mechanical features of the PAT subjected to the braking force, i.e., torque M and mechanical power P M , were thus measured by the test bench. Figure 6 illustrates the evolution of M (top) and P M (bottom) as a function of the PAT speed N. Each dataset and the related interpolating curve refer to a specific frequency of the feed pump, which ranged between 35 and 50 Hz. The torque M decreases with both the increase of the PAT rotational speed N and the decrease of the feed-pump frequency. Differently, the mechanical power P M initially increases with the rotational speed up to a peak value, then decreases for higher values of N. Such trend is more evident in case of higher feed-pump frequencies (e.g., 50 Hz), where two points of the upper series, corresponding to N = 1250 rpm and 1350 rpm, are located farther from the interpolating curve. Observing the interpolating curves, the peak of each P M curve tends to move towards larger values of N, with the maximum power being reached for N ∼ = 1000 rpm when the feed-pump frequency is relatively small (35 Hz) and for N ∼ = 1250 rpm when the feed-pump frequency is relatively large (50 Hz). This suggests that the peak mechanical power that can be obtained from the PAT system increases with both N and frequency. In other words, the larger is the flow rate, the larger is the rotational speed required to get the maximum power. In both panels, the red-highlighted points in the upper curve indicate the tests (i.e., 50 Hz frequency, N = 1650 rpm, and N = 1750 rpm) during which a clearly visible vortex lingered during the whole test. In such cases, the vortex length was of the order of O(1 m), with the N = 1650 rpm case providing a longer vortex, comparable to the transparent pipe length (∼1.7 m, see Figure 2b).
With the aim to directly inspect the effect of the flow rate Q on the mechanical features, Figures 7 and 8 illustrate the evolution of both torque M and power P M , respectively, with respect to the discharge Q flowing through the PAT. The N lines illustrated range between 650 and 1250 rpm, since fewer data were collected for speeds smaller than 650 rpm and larger than 1250 rpm. Hence, data referring to such N values are not here represented. In Figure 7, the torque increases with the flow rate and, usually, decreases with the rotational speed (e.g., the curve referring to N = 650 rpm is significantly higher than that referring to N = 1250 rpm). However, at specific conditions, i.e., specific values of N and Q, the largest torque value might not refer to the smallest rotational speed. For instance, the N = 1250 rpm line intersects and overcomes the N = 1150 rpm line when Q > 8 L/s. This suggests that larger mechanical powers may be reached at sufficiently large flow rates and speeds, being P M proportional to both M and N (see Equation (2)).
The evolution of P M with the flow rate is illustrated using data points and interpolating curves (Figure 8). To better draw the interpolating lines, data from both Test Series 1 and 2 were here used. The power increases with both flow rate and rotational speed, a behavior similar to that characterizing the head drop. However, in this case, the larger is N, the more rapid is the increase of P M . In other words, while large flow rates lead to small differences in ∆H among the N iso-lines (see Figure 5), large differences are observed in the mechanical power.
To properly understand the performances of the PAT system, the efficiency was evaluated for N = 650-1250 rpm, as reported in Figure 9, where the dependence on both flow rate (top) and mechanical power (bottom) is illustrated. The efficiency η increases with the flow rate in the beginning, then decreases. Such trend changes with N, i.e., the larger is the rotational speed, the larger is the discharge at which the maximum efficiency occurs (in agreement with what observed in Figure 6, bottom). Further, the maximum efficiency is significantly larger at higher N values, e.g., while the maximum efficiency is η ≈ 43% for N = 650 rpm, it rises up to η > 60% when N = 1250 rpm. Conversely, relatively small discharges (Q ≤ 6 L/s) lead to a larger efficiency at small speeds (e.g., η = 37% for N = 650 rpm) if compared to what happens at large speeds (η = 25% for N = 1250 rpm). If the efficiency is represented as a function of the mechanical power P M (Figure 9, bottom), the produced power significantly varies when passing from Q = 6.0 L/s to Q = 9.0 L/s, i.e., a 50% increase of the flow rate leads to an increase of the mechanical power of more than 500% (see also Figure 8). The relationship between head drop and mechanical power is also worth investigating, especially in view of the application described in Section 3.3. Hence, Figure 10 illustrates the evolution of ∆H with respect to P M for each investigated N value. While lower N values are related to large head-drop variations (e.g., ∆H ranging between 7.44 and 17.23 m when N = 650 rpm), larger N values are related to large mechanical power variations (e.g., P M ranging between 157 and 837 W when N = 1250 rpm).

Application
Enhancement of supply systems for energy production purposes is particularly suitable for relatively small urban agglomerates. Since the present work aims at finding efficient and integrated solutions for energy production and consumption in real-world contexts, the results of the application to the municipality of Servigliano is here illustrated (see also Section 2.2).
First, the design of a WDN is usually undertaken with reference to the water required by customers during the day of maximum demand. Then, some considerations should be made, especially for what concerns the water demand variability occurring during the day [32,33,35]. Hence, following the analysis of Section 2.2, different scenarios are here investigated starting from the data collected between 2007 and 2013. The yearly variability of the water consumption is described by two representative values of the mean water demand, i.e., µ q = 3.72 L/s (Case 1) and µ q = 7.50 L/s (Case 2), while the hourly distribution of the flow rate is illustrated in Figure 4.
Due to the largely variable daily flow pattern in small urban areas, the use of the tested PAT should be properly calibrated. Exploitation of the experimental results enables one to calculate the mechanical power as a function of the flow rate, based on the interpolating lines shown in Figure 8. Similarly, the produced head drop can also be estimated through the interpolations illustrated in Figure 5. All interpolating curves are second-degree polynomial functions, all with best-fit coefficients R 2 > 0.995.
Application of such interpolating lines enables one to investigate the hourly variation of both mechanical power ( Figure 11) and head drop ( Figure 12). Each case was investigated under three different hypotheses, each related to a specific rotational PAT speed: N = 1250 (solid lines), 1050 (dashed lines), and 850 rpm (dotted lines). This choice was motivated by the dual need to avoid rotational speeds providing significantly small mechanical powers, i.e., N = 650 and 750 rpm (see Figure 8), and have a relatively wide spectrum of PAT working conditions, i.e., N ranging between 850 and 1250 rpm.
Due to the low efficiency at small flow rates (see Figure 9), it was supposed to operate the PAT only when Q ≥ 5 L/s. As shown in Figures 11 and 12, the time ranges during which the PAT system would work are different and depend on the analyzed cases. For Case 1, the PAT would work for 5 h, i.e., during 7-10 and 20-22. For Case 2, the working time would be of 19 h, i.e., during 0-1 and 6-24. Hence, a continuous operation of the PAT system would not occur for Case 1, mainly due to the small flow rate during the nighttime, as expected, but also to the double peaked distribution of the flow rate and the relatively small flow rate between the peaks. Conversely, Case 2 shows a large and continuous exploitation of the PAT during the whole daytime and part of the nighttime, i.e., with the only gap between 1 and 6.  Further aspects can be observed from the analysis of the P M evolution. In detail, the comparison illustrated in Figure 11 highlights the effect of N on the hourly variation of P M . However, due to the relatively small flow rate during Case 1, the rotational speed slightly affects P M and the efficiency is η < 40%, 30% and 25% when N = 850, 1050, and 1250 rpm, respectively. Specifically, the use of an intermediate speed, i.e., N = 1050 (dashed lines), leads to relatively better performances than use of larger (N = 1250 rpm, solid lines) and smaller (N = 850 rpm, dotted lines) speeds. Case 2 shows a non-negligible increase of P M with N, this being due to the larger distance among the N curves at large Q values (Figure 8). In this case, the efficiency is η < 55% for the N = 850 rpm scenario, while it is η > 55% for most of the working time, when N = 1050 rpm or 1250 rpm. The largest efficiency is reached at large flow rates (Q > 8.5 L/s) for N = 1250 rpm.
An important issue is the effect of the water demand. In particular, relatively small values of µ q (e.g., Case 1, blue lines) lead to significantly small values of P M . As an example, the highest demand peak, occurring in the morning between 8 and 9, is associated to a maximum value P M = 94 and 1447 W when the mean demand is, respectively, µ q = 3.72 and 7.50 L/s. Hence, the doubling of the water demand leads to a mechanical power ∼ 15 times larger. In addition, a larger mean water demand provides a more continuous power production, i.e., Case 2 (orange lines) is better suited for the application of the PAT system as it would be operative for 19 h continuously. From the analysis of Case 2, P M increases of about 30% when passing from N = 850 rpm to N = 1250 rpm during relatively low-flow conditions (e.g., between 12 and 13) and about 50% during relatively high-flow conditions (e.g., between 8 and 9). This is due to the larger efficiency and mechanical power obtained with larger N values when the flow rate is large, i.e., Q > 7 L/s (see Figure 9).
On the other hand, the head drop should also be accounted for when choosing the most suitable PAT configuration (Figure 12), as large µ q values lead to large head drops. Further, ∆H is more sensitive to the change in the rotational speed when the mean water demand is relatively small. For instance, when N changes from 850 to 1250 rpm, a variation larger than 60% occurs during the highest peak for Case 1, while smaller variations occur for Case 2 (<10%).
On 17 July 2008, upstream of the Servigliano WDN, a PRV provided a head drop ∆H PRV ∼ = 17 m, which guaranteed a backpressure (BP) downstream of the PRV in the range 25-28 m throughout the day. Figure 13 illustrates the measured pressure upstream (green line) and downstream (yellow line) of the PRV. At a first sight, comparing with Figure 12, the head drop produced by the PRV is larger than the maximum value estimated for the PAT application related to Case 1 (∆H 1 < ∆H PRV ), while Case 2 often leads to larger drops (∆H 2 > ∆H PRV ).   However, in light of the above results and in view of a possible PAT installation, a suitable strategy should be selected, in terms of both: (i) PAT-PRV configuration; and (ii) PAT regulation. First, for the case at hand, a complete replacement of the existing PRV with the analyzed PAT seems to be difficult. This is due to the working conditions tested during the laboratory experiments, since the maximum pressure recorded upstream of the PAT was ∼ 3.5bar, i.e., smaller than that recorded upstream of the PRV. For the real-world application, a PRV-PAT integration is thus suggested, to allow the PRV to reduce the pressure coming from the reservoir, located upstream, and make the PAT work in almost optimal conditions. Second, a further reasoning is required in terms of PAT system design and regulation [2]. Application of an HR approach would be suitable. A regulating valve, such as a PRV, in parallel with the PAT would provide a large dissipation during the nighttime, when the PAT is not working. During the daytime, when the power generation is important, a regulation valve in series with the PAT would dissipate part of the excess pressure to allow the PAT to properly operate. On the other hand, an ER approach would allow the user to exploit different PAT rotational speeds, with the aim to reach the best efficiency and make the PAT work around its BEP. Finally, a thorough analysis of the operating PAT conditions in the WDN and the combined use of PAT, regulating valves and inverter (HER-type approach) might lead to the optimal use of the PAT system [23].

Conclusions
According to the modern trend for a sustainable management of natural resources, the potential energy deriving from the excess of pressure available in several parts of the water supply networks should be recovered and exploited. However, the low values of available power and the large variations of flow rate and pressure drop, with the consequent need for an expensive power plant control system, hinder the diffusion of such practice for small residential areas. In this paper, a centrifugal pump available in a laboratory facility was tested in reverse conditions, with the aim to reproduce real-case conditions. Different hydrodynamic and mechanical forcing actions were tested, accordingly to users' water demand. Relatively large flow rates (Q > 8 L/s) were seen to provide relatively large energy dissipation (∆H > 13 m) and mechanical power (P M > 400 W). Further, an increase of the rotational speed provides an increase of both ∆H and P M , with the former mainly changing at small flow rates (Q < 6 L/s) and the latter mainly changing at large flow rates (Q > 8 L/s).
Results show that this type of application is a suitable solution to harvest energy from conventional water distribution networks at small scale (e.g., neighborhoods). With the aim to reproduce typical real-world conditions, the experimental results obtained from the characterization of an available pump, here used as a PAT, were applied, although we are aware of the need to properly design the PAT application through investigation of further possibilities (e.g., see [8]). Some scenarios were tested by parameterizing the rotational PAT speed and the value of the mean water demand. The choice of such demand was based on the available data collected in the municipality of Servigliano (Fermo, Italy) in recent years. The investigated conditions demonstrate that a suitable choice of the PAT-system use (e.g., rotational speed and operational time) is needed to guarantee a sufficient mechanical power and a head drop compatible with the minimum service level, considering that a larger mean water demand means larger flow rate, hence larger power and head drop. For the case at hand, it was observed that the power (ranging between ∼50 and ∼1450 W) is largely sensitive to the used mean water demand and less sensitive to the PAT operational speed, while the head drop (ranging between ∼6 and ∼24 m) is less affected by such parameters. It can also be stated that the obtained head drops are smaller than those provided by the existing PRV when the mean water demand recorded in Servigliano is used. If the mean demand is twice this value, the head drop presents large oscillations, sometimes being larger and sometimes smaller than the drop provided by the existing PRV. In such conditions, an optimal PAT design should be undertaken, considering the possibility to opt for a hydraulic and/or electrical regulation.
Finally, the design of a pico-hydropower plant sized for each real-case leads to the possibility to produce and sell energy and, consequently, to save management costs in a relatively simple way. Exploiting the results here found and taking into account the reduced cost of a PAT application (e.g., compared to a customized turbine), future studies within the "WISE Buildings" project will investigate the costs and impacts related to PAT applications at neighborhood scale, compared to provided energy benefits, considering all relevant life-cycle stages and taking into account the possible uncertainties related to the future macro-economic scenario, to PAT installation and maintenance costs and to the water supply demand [36,37].