Characterization of Hyporheic Exchange Drivers and Patterns within a Low-Gradient, First-Order, River Confluence during Low and High Flow

Confluences are nodes in riverine networks characterized by complex three-dimensional changes in flow hydrodynamics and riverbed morphology, and are valued for important ecological functions. This physical complexity is often investigated within the water column or riverbed, while few studies have focused on hyporheic fluxes, which is the mixing of surface water and groundwater across the riverbed. This study aims to understand how hyporheic flux across the riverbed is organized by confluence physical drivers. Field investigations were carried out at a low gradient, headwater confluence between Baltimore Brook and Cold Brook in Marcellus, New York, USA. The study measured channel bathymetry, hydraulic permeability, and vertical temperature profiles, as indicators of the hyporheic exchange due to temperature gradients. Confluence geometry, hydrodynamics, and morphodynamics were found to significantly affect hyporheic exchange rate and patterns. Local scale bed morphology, such as the confluence scour hole and minor topographic irregularities, influenced the distribution of bed pressure head and the related patterns of downwelling/upwelling. Furthermore, classical back-to-back bend planform and the related secondary circulation probably affected hyporheic exchange patterns around the confluence shear layer. Finally, even variations in the hydrological conditions played a role on hyporheic fluxes modifying confluence planform, and, in turn, flow circulation patterns.


Introduction
River confluences are nodes in fluvial systems where the combining flows converge and realign further downstream, generating complex hydraulic processes within a region called confluence hydrodynamic zone (CHZ). It is known that confluence geometry, the momentum flux ratio between the merging rivers, the level of concordance of riverbeds at confluence entrance, as well as density differences could cause significant vertical, lateral, and streamwise gradients in velocity forming several distinct hydrodynamic zones [1][2][3][4][5]. Confluences also have important ecological and morphological functions, related to water chemistry, riverine ecology, in-stream, and riparian vegetation [6], physical habitat, as well as biological activity (fish spawning, feeding, etc.), resulting in highly varied habitat for organisms [7][8][9][10].
The hyporheic exchange (HE) has been shown to significantly affect riverine systems [11]. This exchange is characterized by river waters entering the groundwater alluvium as downwelling fluxes and then emerging into the stream as upwelling fluxes. The streambed volume where surface The Onondaga County soil survey [23] indicates that most soils in the study area are derived from glacial till (83%); the rest are derived from glacio-fluvial sediments such as outwash, kames, and terraces (8.9%), postglacial lake sediments (2.6%), recent alluvial sediments (4.3%), and recent organic deposits (1.1%). According to the survey, soil permeability ranges from less than 2 to more than 51 mm/h. Climate in this area is characterized as humid continental and is moderated somewhat by the Great Lakes, especially the most proximate of these lakes, Lake Ontario. Lake Ontario creates frequent cloudiness and "lake-effect" precipitation when relatively cool air passes over relatively warm lake waters.
Precipitation from late October through late March can be in the form of local snow squalls that produce an average snowfall of 2768 mm/year. As there was no meteorological station in Marcellus, the data collected at Syracuse Hancock International Airport weather monitoring station, located approximately 25 km from the study site, were used. The 1055 mm/year average precipitation reported at the airport is relatively evenly distributed throughout the year, although precipitation is slightly less in the winter, when moisture-holding capacity of the air is lower. Average annual runoff in this area is about 483 mm.
In this study, two field campaigns were conducted: one during the fall low flow and snow-melt season from September to December 2018 (FS-BBCB1) and the other during a spring high flow season from March to April 2019 (FS-BBCB2). The site was chosen based on accessibility and scale: the confluent channels were small enough to be surveyed in detail for studying spatial and temporal variability, relation between fluxes and hydraulic conductivity, comparison with a 1D heat transport analytical model, adopting compact survey instruments (Table 1).

Instrumentation and Data Post-Processing
The flowrates at the BBCB confluence was measured using the float method. Soil samples were collected in the confluence area to identify sediment granulometry and hydraulic conductivity Kv. Vertical temperature profile monitoring was deployed within the confluence as a suitable and accurate method to monitor hyporheic flux across the riverbed, using heat as a natural tracer within a one-dimensional (1D) model [21,[24][25][26]. The details of this monitoring are provided in Section 3.2. Other methods to infer hyporheic exchange, such as passive solute tracers [27] and seepage meters [28] to determine the patterns and the magnitude of hyporheic water exchange, were not utilized in this field study due to temperature profiles providing better spatial resolution within the small confluence. Data were collected during two field campaigns, in the low-flow period from September to December 2018, and in the high-flow period from March to April 2019 (Table 1).

Riverbed Characteristics, Grain Size Analysis and Kv
A total station Topcon GTS-250 was deployed to survey riverbed elevation data and Surfer 15 was used to process them for spatial analysis, using a natural neighbor as gridding method with a surveyed point density of 0.90/m 2 . Kennedy et al. [29] suggested a minimum point density of about 0.05 points/m 2 to reduce the occurrence of error value of 10%. Field tests provided in situ vertical hydraulic conductivity Kv, following a simplified approach of that of Hvorslev [30] proposed by Chen [31] for the vertical component. A vertical standpipe in the stream channel was pressed into the streambed and water is poured into the pipe to fill the rest of the pipe. Due to the difference of hydraulic heads at the two ends of the sediment column in the pipe, water flows through the sediment column and the water table in the pipe falls. Statistical analysis of Kv took into account two different methods [31] for hydraulic head readings. In this study their results were averaged: where Lv is the thickness of the measured streambed in the pipe, h1 the hydraulic head in the pipe measured at time t1, and h2 the hydraulic head in the pipe measured at time t2. The advantage of field-based tests for Kv over laboratory-based permeameter test for Kv may not give representative results since soil core sampling is a disruptive process. Test areas were located in tributaries upstream of the junction and in the CHZ ( Figure 2). Water level was assumed to be constant during slug tests, when no precipitation in the watershed and rise in river stage were observed. Test readings were collected by pouring water into a transparent pipe and taking note of successive negative piezometric heads. Soil samples were collected at BBCB site ( Figure 2) and each one was dried and poured into a rototap for shaking and then categorized. Along with the cumulative curve, coefficient of uniformity η = (d84/d16) 0.5 , and porosity n = 0.255 (1 + 0.83 η ) were estimated following Vuković and Soro [32]. Three set of samples were extracted from BB, CB, and within the CHZ.

Temperature Time Series and 1D Heat Transport Modeling
For the vertical temperature profiles [33], six 2-cm diameter PVC pipes encasing wooden dowels with temperature probes, called iButtons (iButtonLink, LLC., Whitewater, WI, USA), were used in BB, CB and CHZ areas (Figures 3 and 4). The PVC pipe sleeves and dowels were drilled to create inserts for the temperature probes at distances of either distances of 5 cm or 20 cm. The iButton DS1922L was used for this study: each sensor has an accuracy of +/− 0.5 °C (from −10 °C to +65 °C) and resolution 0.0625 °C for 11 bits. To secure the iButtons inserted in the PVC encased dowels, they were sealed with a silicon glue and let to dry for 24 h, which is shown to allow for a clear temperature signal while preventing corrosion.  The temperature profile rods, PVC with encased dowel, were driven into the riverbed to a depth which left the top iButton temperature sensors at surface-subsurface interface, and the subsequent sensors within the riverbed: profilers in the fall low flow season had a 20 cm gap between sensors, and profilers in the spring high flow season had a 10 cm gap between sensors. Flux magnitudes and directions are referred between streambed and the deepest sensor: center-of-pair depth was considered 20 cm and 10 cm below the bed, in FS-BBCB1 and FS-BBCB2, respectively. Temperature time series were recorded at a 5-min or 1-min interval. These rods were inserted into the riverbed and removed from it at the end of each observation, in September 18 (0918), October (1018), and December (1218), and in March (0319). The small bed shear stresses, due to shallow flows across the low-gradient confluence, posed little risk of scouring around the temperature sensors.
Temperature time series data were processed with the VFLUX 2 code which is distributed as an open source MATLAB toolbox [34,35]. Sediment and thermal parameter are listed in Table 2, and every time series was resampled to the "lowest common denominator" to trim the series to the shortest time range that is common to all the input series and interpolates and resamples the input series to have the lowest sampling rate of all the input series. The time series were reduced to 12 samples per diurnal cycle to reduce noise and improve the Dynamic Harmonic Regression model [36] used by VFLUX 2 efficiency in the filtering process [34]. This produced a time-varying apparent amplitude and phase coefficients for the time series, extracting harmonic signals from dynamic environmental systems [27,37]. A non-stationary approach for diurnal signal is mandatory because streambed temperature fluctuates over time due to weather and seasonality, fluxes having different temporal scales. VFLUX 2 identifies a trend, the fundamental signal (ω1), and the first and second harmonics (ω2 and ω3) using an auto-regression (AR) frequency spectrum created with the Captain Toolbox [36]. Table 2. Input parameters of VFLUX2 code. β is dispersivity, KCAL thermal conductivity, CSCAL and CWCAL volumetric heat capacity of sediment and water, respectively.

Parameter
Value The VFLUX 2 model analyzes the temperature profile between iButton sensor pairs, based on a "window" for sensor-spacings, which was set to 1, meaning fluxes were estimated between sensor 1 and 2, and 2 and 3, each either separated by 10 or 20 cm. The hyporheic flux rate was based on the Hatch amplitude method to calculate the vertical fluxes [38], which is an analytical solution to the 1D heat transport equation [39]: where κe is effective thermal diffusivity, q is fluid flux, Cw is the volumetric heat capacity of the saturated streambed, and C is the volumetric heat capacity of the saturated sediment calculated as the mean of Cw and Cs, the volumetric heat capacity of the sediment grains, weighted by total porosity. The effective thermal diffusivity is defined as: where λ0 is the baseline thermal conductivity (absence of fluid flow), excluding the effects of dispersion, β is thermal dispersivity, and c and ρ are specific heat and density of the sediment-water system respectively and is the linear particle velocity (m/s). The second term in Equation (3) represents the increase in effective thermal diffusivity caused by hydrodynamic dispersion and it is often assumed to have little influence in models with modest fluid flow rates [38]. The method provided by Hatch et al. solves for the vertical water flux between two sensors as a function of amplitude differences between the sensors' temperature signals: where q is vertical fluid flux in the downward direction (m/s), Ar is the amplitude ratio (a measure of amplitude attenuation) between the lower sensor and the upper sensor (dimensionless), Δz is the distance between the two sensors in the streambed (m), v is the velocity of the thermal front (m/s) and P is the period of the temperature signal (s). Equations (3) and (4) need to be solved iteratively (or by optimization) and depend on thermal sensitivity which, in turn, is estimated on empirical ranges. The analytical model, Equation (4)

Confluence Geometry and Hydrodynamics Characteristics
BB and CB were two first-order streams where water level was predominantly shallow over this field study, constituted by low-gradient velocities and pressure variations ( Table 3). The planform geometry had a junction angle between the tributaries of approximately 80° in base-flow conditions, and a 40° angle during one high-flow event in December 2018 during liquid precipitation and snowmelt ( Figure 5), while back-to-back angle between tributary and confluence downstream channel were: 145° and 150° (CB and BB) in base-flow conditions, whereas 142° and 162°, in high-flow conditions. Water levels, velocities, and flowrates at the BBCB confluence were measured only at the beginning of the study. However, these values could be considered as indicative of typical low flow conditions within an acceptable range of uncertainty because in those conditions USGS gauge downstream and in nearby rivers did not record any flow events greater than a 1.1-year frequency and indirect observations, including those from piezometer installations, showed no notable change in the water leveled. Larger velocities were observed from CB due to its bed morphology and steep riffle slope into the confluence, with a velocity ratio of BB to CB, VR = Ubb/Ucb = 0.42 and a momentum flux ratio, QR = ρQbbUbb/ρQcbUcb = 0.64. The location of the shear layer moved towards the right bank or BB side of the confluence due to the dominant CB flow velocity (see the dotted red line in Figure 5). Downward fluxes from prior channel forming flows eroded the BB riverbed forming a large scour hole within the CHZ (see Figure 6). Flow paths induced by bed topography in CB defined the length and width of a sand bar located downstream from the CHZ [12,40] and caused fine sand infiltration into the bed [45,24] which could cause lower Kv. Table 3. Low flow active channel width, depth, average velocity, discharge, Froude and Reynolds numbers in BB, CB, and in the CHZ. Data for BB and CB were collected 1.5 m upstream of the junction, and data for CHZ were collected 3 m downstream of the river junction.

Bed Morphology
The confluence was characterized by low-gradient water surface slopes, with slightly higher slopes in the CB tributary in the 5 m upstream the junction. The area between BB and CB was abundant in outwash sediments and partially submerged during high-flow discharge event (i.e., in December after a sudden snow melt, Figure 5) complicating the localization of the BB and CB riverbanks ( Figure 6). The deepest pool was found in BB, at a scour hole of approximately 40-50 cm wide, along the outer bank as common in pool-riffle rivers [41][42][43], while CB and the CHZ depths were mostly without pool and averaged 5-10 cm. Sediment scour was located in the BB pool and outer bank, and depositional areas were observed downstream the confluence on the left bank and CB flow side, with a high presence of pebbles and fine sand on the river bottom.

Hydraulic Conductivity and Grain Size Analysis
Hydraulic conductivity tests result showed very low Kv values throughout the confluence. The values ranged from 0.09 to 0.005 m/d (Figure 7). According to mean and median Kv in BB and CB and the CHZ, CHZ3 had the smallest hydraulic conductivity. That area was subjected to sand (0.075 mm < PZ < 2 mm) deposition during fall low flow season that might have decreased Kv values due to layering of streambed sediments [44]. In fact, laboratory analysis of substrate samples showed that grain size in the confluence bed was mostly composed of fine sand (0.063 mm < PZ < 0.2 mm). The average of cumulative percentages by weight is listed in Table 4. The silt-clay fraction, instead, was larger in CHZ sediment sample while, on average, BB and CB showed lower values (Figure 8). Table 4. Sediment size distribution about the confluence, reporting the cumulative weight (%) for the two size fractions of sand and finer than sand, the particle diameter (mm) for 14%, 50%, and 84% finer than the diameter, coefficient of uniformity, and porosity.

Temperature Time Series and VFLUX Code Application
Temperature profiles obtained across the confluence were used in VFLUX to get directions (noted as positive values indicate downwelling flux), magnitudes and patterns of vertical hyporheic fluxes in multiple locations over several months. Temperature differences between the groundwater and surface water in FS-BBCB1 and FS-BBCB2 were less than 2 °C and 1 °C, respectively.

Fall Low Flow and Snow-Melt Season
During the fall season, variations in flux direction within the confluence were observed within the top 20 cm of the riverbed by temperature profile analysis. The probes at greater depths did not register sufficient temperature variation to reveal as vertical hyporheic fluxes. The vertical hyporheic fluxes had seasonal trends. In late summer, from 16 to 23 September, fluxes ranged from +1.12 mm/day (downwelling) to −2.61 mm/day, with four of these upwelling fluxes in the majority of the confluence (0918A, 0918B, 0918C, and 0918E, Figure 9). The single downwelling flux (0918D) was observed at the scour hole section of the confluence.
In the mid-fall period, from 23 October to 6 November, there were three distinct patterns of vertical hyporheic exchange, during which time the site received 55 mm of precipitation and river stage increased ~6 cm or 30%. At the beginning of this wet period, from 23 to 25 October, maximum downwelling fluxes of 405 mm/day were observed around rods 1018A, 1018B, 1018C, and 1018F in the upstream section, and upwelling in the downstream section ( Figure 10). In this period, the maximum daily upwelling fluxes gradually transitioned from −400 to −145 mm/day at rod 1018E, while upwelling remained steady at 1018D. Second, on 26 October, rod 1018E flux direction changed to moderately downwelling from a strong upwelling, and the upwelling at 1018D in the BB section of the confluence increased to a maximum of −140 mm/day. The third pattern emerged from 1 to 6 November when the upwelling hyporheic flux shifted further upstream along the BB side of the confluence to rods 1018A and the downwelling at rod 1018B ceased and became neutral ( Figure 10). These changes in flux pattern suggest that BB transitioned to greater upwelling during the wet period, while downwelling flux in the CB section of the confluence was relatively steady.  In late fall during 2-4 December, after a month of little rainfall, the hyporheic fluxes reversed from the mid-fall pattern. The upwelling fluxes were organized along the CB upstream section of the confluence, while downwelling fluxes were observed along the downstream confluence section and into the upper BB section. In this period, the CB temperature rods (1218A and 1218B) registered upwelling fluxes, while rods 1218D and 1218E had strong downwelling fluxes ( Figure 11). The flux rates ranged from 602 mm/day to −397 mm/day, reaching greater values than in the mid-fall period. As with the late summer period, but unlike the mid-fall with the rains, the December fluxes were steady values over the sampling period even though there was a steady decline in river stage.

Spring High Flow Season
The spring season brought changes in river flow, and this was used to organize three periods of distinct patterns in hyporheic flux. The changes in flow were attributed to a rainfall event between 29 and 31 March and another period of rainfall between 3 and 7 April. At the end of the March rained, downwelling fluxes were observed downstream of the confluence, with an isolated corner of upwelling at rods 0319E and 0319F ( Figure 12). During the period between the rains, on 1 April, the hyporheic flux pattern shifted and upwelling now existed across most of the confluence, at all rods except for the rod 0319C in the upper confluence where CB entered. The continuation of rains from 3 to 7 April resulted in a general return to the late March pattern of flux, with downwelling extending across most of the monitoring section, and upwelling at rod 0319E in the downstream section along the CB region, as well as at rod 0319D near the confluence vertex.

Discussion
Regional to local drivers of hyporheic exchange can gather within the confluence hydrodynamic zone. At a regional scale, the dominant drivers of hyporheic exchange flux patterns are the relative levels of river stage and groundwater [11][12][13]21,22], while at local scale bed morphology, soil heterogeneity, and channel velocity influence hyporheic exchange [13]. In pool-riffle channels with moderate slope, such as BB and CB, hyporheic exchange is usually driven by the variability of the spatial distribution of channel velocity and resulting pressure head [40]. Downwelling and upwelling zones are usually located on riffle head with lower velocities (higher pressure) and riffle tail with higher velocities (lower pressure), respectively [25]. Local topography is a prominent driver of changes in hyporheic flux direction when bed depth increases or decreases in the downstream direction, and the concave or convex nature water surface profiles can also change hyporheic flux direction [45]. On bedforms, past studies demonstrated that close to the detachment point downstream of dune crest and to the reattachment point on the dune stoss side are minimum and maximum pressure regions, respectively, creating patterns of upwelling and downwelling [46]. This field study found distinct upwelling or downwelling patterns of hyporheic exchange flux and observed its variation across eight months from late summer to spring seasons. During this period, these patterns exhibited variability while hydrodynamic and hydrological condition were changing. However, as BB and CB were ungauged streams, daily measurements of discharge, and water stage were not available. These data were collected at some characteristic locations of the confluence (Figure 13

Effect of Scour Hole on the Hyporheic Fluxes
In September 2018, at the confluence entrance the flow from CB tended toward the BB bank (Figure 5left). At that time the area of measurement was located just downstream the junction corner, where the flow from BB is featuring an abrupt step at the entrance of the scour hole ( Figures  9, 13, 14 and 15a). The flow over a step is a classic type of separation flow, termed backward facing step flow (BFSF), which has been extensively investigated using both experimental [47] and numerical methods [48] in laminar and turbulent flows. It is well-known that in the BFSF downstream the step bottom pressure is going down which is followed by a rapid increase to get a maximum close to the reattachment point. While in laminar flow the location of the minimum/maximum pressure point is depending upon the step height-based Reynolds number [48], in a turbulent BFSF the point of minimum and maximum bed pressure is located at x/Hstep = 3.0 and x/Hstep = 9, respectively ( Figure 16) [47]. In our case, as the step height is approximately 0.15 m, the maximum pressure should be located about 0918D point (Figure 15a). This is consistent with the observed hyporheic fluxes, which were directed upward (upwellings) upstream and immediately downstream of the step bordering the scour hole and downward (downwelling) around 0918D point, where flow reattachment and maximum pressure should be located. On the other hand, in the area of measurement, the flow from CB is moving over a plane bed, where flow was accelerating, and upwelling was observed.   It should be noted that the PVC rod piezometer installations across the CHZ indirectly showed no notable change in the bed morphology. Additionally, the location of the scour hole remained unchanged during the field study. It is expected that changes in the location of the scour hole occurring on a longer timescale could modify the hyporheic exchange at the confluence.

Effect on Variations in Confluence Geometry on the Hyporheic Fluxes
In December 2018 a snowmelt event increased discharge and water level at the confluence and the junction angle/location as well as the circulation at the confluence was accordingly modified (Figure 5right). The confluence junction as well as the stagnation zone shifted upstream, while the location of the shear layer moved toward the CB bank (Figure 5right). The area of measurement in December 2018 was partially overlapping with that of September 2018, as it was located more upstream and it was only bordering the scour hole (Figures 11, 13, 14 and 15b). In December 2018, in that area, the flow partially moves over the location of the junction in low flow conditions ( Figure  15b), where upwelling was observed, and partially over a stepped bed, where downwelling was measured. Comparatively, the area and the rate of downwelling increased from September to December 2018. This might be explained by the observed changes in the main flow patterns at the confluence entrance.

Effect of Secondary Flows on the Hyporheic Fluxes
In October/November 2018 and March/April 2019 the area of measurement was located downstream of that in September and December 2018, in the shear layer region (Figure 13), where hydrodynamics is generally characterized by complex 3D patterns and helical flow cells are also often observed [40], although their presence, characteristics and origin need further investigations [19,49]. Following the back-to-back bend or meander analogy, these cells are expected to converge at the surface in the center of the channel and to diverge near the bed [1,40,41]. Furthermore, these helical cells are associated with downward and upward flow patterns in the water column which could have an impact even on the hyporheic exchange. Cheng et al. [22] observed at the confluence between Juehe River and Haohe River (junction angle, 110°) downwelling patterns in the area across the shear layer where helicoidal flow cells were located. They argued that the encounter and impact of the two tributaries created in that area a downward flow causing a downwelling hyporheic exchange. In the present study, it was not possible to confirm or not the presence of helical cells at the BBCB confluence. However, confluence planform ( Figure 6) and the related bend-like flow patterns of the tributaries might suggest the presence of the above secondary circulation. In October/November 2018, downwelling/upwelling was observed on the CB/BB side of the area of measurement, respectively, but some variations were noted from October to November (Figure 10).
In March/April, the distribution of the hyporheic fluxes was different, as almost only downwelling was measured on 31 March and 6 April, while on 1 April upwelling was predominant ( Figure 12). To try to explain this strong variability, two cross-sections located in the measurement area October/November 2018 and March/April 2019 were considered ( Figure 14) and the distribution of the hyporheic fluxes was plotted (Figure 17a,b). In October/November 2018 and March/April 2019 a downwelling region was observed across the shear layer about the scour hole (Figure 17a,b). This finding is consistent with the observations by Cheng at al. [22] and it could be related to the bed pressure distribution across the back-to-back bend at the confluence. At the end, the observed patterns in the distribution of hyporheic fluxes seem to be related to the hydrodynamics and morphodynamics characteristics about the confluence and their changes during the hydrological cycle. Given the role of confluence junction angle in influencing hyporheic exchange flux, patterns of hyporheic fluxes are expected to fluctuate with changes in flow depth if the junction angle changes with channel depth of water. Further, given the role of momentum flux ratio influencing hyporheic flux, differences in water characteristics that lead to changes in density, temperature, conductivity, and suspended sediment concentration would likely trigger changes in hyporheic exchange patterns [19].

Conclusions
In the literature about the environmental interfaces [50] few studies are available regarding the hyporheic exchange at river confluences. This experimental research characterized the spatial and temporal patterns of vertical hyporheic exchange flux about a small headwater confluence in the USA. The field data and its analysis were used to explain the observed patterns of hyporheic exchange by confluence hydrology, geometry, hydrodynamics, morphodynamics, grain size distribution, and vertical hydraulic conductivity. Furthermore, the effect on the hyporheic exchange due to some classical features of a confluence flow, such the stagnation zone, flow deflection, and contraction zone, including the scour hole, and the shear layer was investigated. Finally, to expand on the two prior studies of hyporheic exchange at a confluence under baseflow, this study monitored across eight months to capture low flow and high flow patterns. Principal outcomes found within this research are: • Soil samples showed that BBCB site was mostly sandy-gravel and hydraulic conductivity tests reported very low values, suggesting that local sediment transport processes allocated fine sediments into pores, reducing soil permeability. • Confluence geometry, hydrodynamics, and morphodynamics were found to significantly affect hyporheic exchange rate and patterns. In September and December 2018, local scale bed morphology, such as the confluence scour hole and minor topographic irregularities, influenced the distribution of bed pressure head and the related patterns of downwelling/upwelling. • Variation in hydrological conditions during a high flow event in December 2018 survey were seen to modify confluence geometry, such as junction angle and position, and, in turn, flow circulation patterns, shifting back the stagnation zone and relocating the shear layer. The hyporheic flux pattern in low flow conditions was modified where upwelling was mostly observed, and partially over a stepped bed, downwelling was measured. • In October/November 2018 and March/April 2019, classical back-to-back bend planform and the related secondary circulation might probably affect hyporheic exchange patterns around the confluence shear layer as already documented in the literature [22]. • Seasonal hydrological condition should be taken into account. There was a visible pattern among October 2018 and March 2019 temperature rods: in these two cases fluxes were not only driven by morphological or hydrodynamic conditions.
Follow-up work must focus on the relationship among soil permeability, flow momentum changes, and groundwater which are still under investigation for this complex study. A continuous monitoring of streams discharge, velocity, and water depth, as well as and vertical fluxes is advisable to reduce the uncertainty in the analysis of hyporheic dynamics within a complex riverine system such as a confluence and to highlight main factors such as seasonal and regional changes and drivers of surface-subsurface water interaction.