Next Article in Journal
Comparison of Zooplankton Community Patterns in Relation to Sediment Disturbances by Dredging in the Guemho River, Korea
Next Article in Special Issue
On Neglecting Free-Stream Turbulence in Numerical Simulation of the Wind-Induced Bias of Snow Gauges
Previous Article in Journal
A New Runoff Routing Scheme for Xin’anjiang Model and Its Routing Parameters Estimation Based on Geographical Information
Previous Article in Special Issue
Comparison Study of Multiple Precipitation Forcing Data on Hydrological Modeling and Projection in the Qujiang River Basin
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Parameterization of the Collection Efficiency of a Cylindrical Catching-Type Rain Gauge Based on Rainfall Intensity

1
Department of Civil, Chemical and Environmental Engineering, University of Genova,16145 Genoa, Italy
2
WMO/CIMO Lead Centre “B. Castelli” on Precipitation Intensity, 00062 Vigna di Valle (RM), Italy
*
Author to whom correspondence should be addressed.
Water 2020, 12(12), 3431; https://doi.org/10.3390/w12123431
Submission received: 9 November 2020 / Revised: 3 December 2020 / Accepted: 4 December 2020 / Published: 6 December 2020

Abstract

:
Despite the numerous contributions available in the literature about the wind-induced bias of rainfall intensity measurements, adjustments based on collection efficiency curves are rarely applied operationally to rain records obtained from catching-type rain gauges. The many influencing variables involved and the variability of the results of field experiments do not facilitate the widespread application of adjustment algorithms. In this paper, a Lagrangian particle tracking model is applied to the results of computational fluid dynamic simulations of the airflow field surrounding a rain gauge to derive a simple formulation of the collection efficiency curves as a function of wind speed. A new parameterization of the influence of rainfall intensity is proposed. The methodology was applied to a cylindrical gauge, which has the typical outer shape of tipping-bucket rain gauges, as a representative specimen of most operational measurement instruments. The wind velocity is the only ancillary variable required to calculate the adjustment, together with the measured rainfall intensity. Since wind is commonly measured by operational weather stations, its use adds no relevant burden to the cost of meteo-hydrological networks.

1. Introduction

Systematic errors (biases) in precipitation measurements are commonly accounted for by means of correction models that can be expressed in the general form
P c = k [ P g + i Δ P g i ]
where P c is the corrected figure, P g is the gauge-measured precipitation, i Δ P g i is the sum of correction terms for various error sources, and k is the wind deformation coefficient. The detailed model, originally proposed by [1], was later modified by [2] to account for both liquid and solid precipitation and can be written as
P c = k r ( P g r + Δ P w r + Δ P e r + Δ P m r ) + k s ( P g s + Δ P w s + Δ P e s + Δ P m s )
where Δ P w , Δ P e and Δ P m are the correction terms for wetting, evaporation, and mechanical errors, respectively, while subscripts r and s refer to liquid (rain) and solid (snow) precipitation (see also [3]). This formulation reveals that the adjustment of catching (environmental) biases due to the wind applies to the precipitation amount once this is corrected for counting (instrumental) biases. The adjustment factor k is reportedly a function of the wind speed and precipitation intensity, and its value ranges between 1.0 and 1.15 for rain and between 1.0 and 2.0 for snow measurements [4].
The correction of precipitation measurement biases is applied to daily or monthly totals or, in some practices, to individual precipitation events [3]. However, since the precipitation intensity and the wind velocity are among the influencing variables, the most relevant sources of error act at very short to instantaneous timescales, at which point such factors may vary significantly. Corrections are often non-linear functions; therefore, it is important to develop correction algorithms that can be easily applied at the minimum temporal resolution of operational measurements (e.g., one-minute for rainfall intensity, as recommended by [3]).
The influence of wind on precipitation measurements is due to the interaction between the gauge body and the airflow. Any precipitation gauge behaves as a bluff-body when impacted by wind, and this interaction produces airflow deformations around the obstacle. Generally, upward velocity components arise upwind of the collector and wind accelerates above it [5,6]. This aerodynamic effect deflects the hydrometeors (liquid/solid particles) with respect to their undisturbed trajectories [4,7], and is responsible for a significant reduction in the collection performance. The main factors of influence are the gauge geometry, the wind speed, and the type of precipitation (liquid or solid) and its characteristics, including the crystal type, Particle Size Distribution (PSD) and precipitation intensity [8,9].
The problem of the wind-induced bias on precipitation measurements is addressed in the literature using both numerical simulation (Computational Fluid Dynamics (CFD) and particle tracking) and experiments (field and wind tunnel tests). Generally, wind produces underestimation in precipitation measurements, except for gauges with peculiar shapes (e.g., the Hotplate© precipitation gauge, see [10]). Reference [1] reported that the typical magnitude of the wind–induced losses (undercatch) for the precipitation amount is 2–10% in case of liquid precipitation and 10–50% in case of solid precipitation. Field studies focusing on solid precipitation [9,11] showed collection losses up to 70–80%, while [12] reported an observed undercatch of about 10 to 23% for liquid precipitation at a lowland and upland site, respectively. Nevertheless, the implementation of adjustments based on correction curves in operational conditions is still uncommon.
The drawbacks of adjustment functions derived from field experiments alone are related to their strict dependence on the site where the test field is geographically located, the associated precipitation and wind climatology, and on the reliability and accuracy of the assumed reference gauge. The observed Collection Efficiency (CE) values derive from the actual drop size distribution of precipitation events and the microphysical characteristics of the hydrometeors. Complete parameterization of these CE curves is rarely achieved, so that a large dispersion of the field-measured data around the best-fit curves usually persists.
It is evident that a theoretically based approach is needed, though still based on real-world observations for proper validation of the algorithms and results, to achieve a complete coverage of various local climatological characteristics, precipitation microphysics, gauge shapes and wind conditions. This can be achieved by exploiting the potential of numerically solving the basic equations of fluid motion and of particle-fluid interactions, as in our proposed method. In the present work, we base our study on CFD simulations already performed by [13] for a cylindrical gauge which has the shape of the most widely used precipitation gauges.
With the aim of reducing the dispersion of field data around experimentally derived adjustment curves, and shedding light on the dependence of such curves on the drop size distribution and its link with the precipitation intensity, [14] recently showed that such dispersion can be reduced by including the results of the numerical simulation into the best-fit methodology applied on field measurements. The authors analysed WMO-SPICE quality controlled 30-min accumulation data from the Marshall field-test site (CO, USA) and revealed that the wind-induced undercatch of precipitation gauges is best correlated with the measured precipitation intensity, rather than temperature (widely used, e.g., in [15]), in addition to wind speed. The measured precipitation intensity indeed has the advantage of including information about the particle size distribution [16]. The optimal curve fitting used by [14] to derive adjustment curves for the Geonor© T200B gauge in a Single Alter shield and in a reference configuration indicated that accounting for precipitation intensity indeed reduces the scatter of the residuals. This result is confirmed by the analysis of data from other field test sites, such as CARE (Canada) and Haukeliseter (Norway), and shows consistent behaviour under different climatological conditions.
The physical basis for the improved parameterisation of the adjustment curves obtained by using the measured precipitation intensity was shown to derive from the correlation of large particles with high intensities. Large particles are preferentially collected by the gauge, even in strong wind, due to their higher fall velocity, allowing them to break through streamlines of flow above the gauge. The numerical modelling was able to reproduce the collection efficiency pattern observed in the field. The authors’ findings provide an attractive method to improve operational measurements, since no additional instrument, except for a wind sensor, is required to derive the adjusted estimates of snow accumulation.
In the present work, the formulation of CE curves as a function of wind speed ( U r e f ) is derived for a typical cylindrical gauge and parameterized with the Rainfall Intensity (RI). Easy-to-use adjustment curves are finally obtained as a function of the rainfall intensity measured by the gauge (RImeas) and wind speed.

Existing Correction Algorithms

Adjustment curves can be derived using data from experimental sites equipped with different precipitation gauges in operational conditions, and a reference one. In field studies, the ratio between the precipitation measured by a gauge in operational conditions, h m e a s (usually in (mm)) for a given wind speed, U r e f (m s−1) and the reference one, h r e f   (mm) is called the Collection Efficiency (CE)
C E = h m e a s ( U r e f ) h r e f
The World Meteorological Organization (WMO) recommends using a gauge placed in a pit as the reference instrumental configuration for liquid precipitation, with the gauge orifice at ground level, sufficiently distant from the nearest edge of the pit to avoid in-splashing. A strong plastic or metal anti-splash grid with a central opening for the gauge must cover the pit, except for the central opening where the gauge orifice is located (construction details are provided in [17]). Because of the absence (or very limited effect) of wind-induced bias, pit gauges generally report more precipitation than any elevated gauge.
The reference installation for solid precipitation is known as the Double Fence Intercomparison Reference (DFIR) [18]. It has octagonal vertical double fences surrounding a storage or automatic gauge, which itself is equipped with a Single Alter shield. Note that this reference configuration is not free from measurement biases itself, and its construction could be improved [19].
At an experimental site in Haukeliseter (Norway), two Geonor© T200B weighing gauges, in unshielded and single Alter shielded configurations, were installed close to the DFIR. Temperature measurements were also available, and anemometers were located at the height of ten meters and at the gauge collector height. The authors classified the precipitation in solid, mixed, or liquid [15], according to the air temperature thresholds reported by [20]. For temperatures T < −2 °C the precipitation is mainly falling as snow, and the CE has a characteristic fast decreasing behavior with the wind speed. For T > 2 °C, where the precipitation is mainly falling as rain, the CE is less influenced by the wind. Rain, snow and mixed precipitation occur in the range −2 °C ≤ T ≤ 2 °C, and a larger scatter appears depending on the precipitation type. Based on a three-year dataset from the Haukeliseter test site, containing several concurrent observations of the CE, the following adjustment curve was formulated by [15]
C E =   [ 1 τ 1 ( τ 2 τ 1 ) e ( T T τ s τ ) 1 + e ( T T τ s τ ) ] e ( U r e f θ ) β + τ 1 + ( τ 2 τ 1 ) e ( T T τ s τ ) 1 + e ( T T τ s τ ) + σ ( T ) ε
where β and θ are two fitting parameters, T τ is the temperature threshold and defines the transition between the two limits above, while s τ indicates the fuzziness between rain and snow, and σ ( T i ) is a parameter governing the variance in the measurement error.
The equation was obtained starting from the assumption that CE is a function of wind speed and air temperature, in the form
C E = f ( U r e f , T ) = [ 1 τ ( T ) ] e [ U r e f θ ( T ) ] β ( T ) + τ ( T )
the parameter τ ( T ) goes from one limit, dry snow, to another, mixed precipitation, when the temperature increases/decreases. A sigmoid function reasonably fits experimental data yielding the parametric function as follows
τ ( T ) = τ 1 + ( τ 2 τ 1 ) e ( T T τ s τ ) 1 + e ( T T τ s τ )
Application of the adjustment curve yields some residual differences between the adjusted accumulation and the reference one, which are probably ascribable to the actual (unknown) particle size distribution.
Data from winter 2010 in the two experimental sites of Marshall (USA) and Haukeliseter (Norway) were analysed by [21]. The authors proposed the following exponential shape for CE
C E = e a ( U ) ( 1 [ tan 1 ( b ( T ) ) + c ] )
where the experimental parameters a , b and c vary with the height of the anemometer and the type of precipitation gauge (unshielded, Single Alter shielded, etc.). After correction, a significant scatter of data persists, which is probably due to the effect of noise, the spatial variability of precipitation and also the spatial variability in crystal type, that are not fully taken into account in this study. With the aim of deriving adjustment curves that could be extended to other sites, data from eight experimental sites were further analysed by [22]. The study provided the parameters of Equation (7) for Single Alter shielded and unshielded chimney shaped weighing gauges, by separating mixed and solid precipitation, and for wind speed measured at ten meters or at the collector elevation.
The dataset obtained by [23] at the Formigal (Spain) experimental site was divided into two samples, and adjustment curves were derived for tipping-bucket rain gauges at one- and three-hours accumulation. For one-hour accumulation, the authors propose Equation (8), where a contribution of the melting of snow during the previous hour of accumulation is also included
T r u e A c c ( 1 h ) = A c c C E 0.095 A c c C E + 0.095 A c c ( p r e v h )
where T r u e A c c ( 1 h ) is the adjusted hourly precipitation, A c c is the measured one, and   A c c ( p r e v h ) is the cumulated precipitation in the previous hour.

2. Method

In the present work, the airflow field (velocity magnitude and components) around a cylindrical gauge, the Casella© tipping-bucket gauge (hereinafter Casella, see Figure 1), was adopted to simulate the trajectories of water drops and to calculate the CE based on a suitable PSD. We started from the CFD simulations (see Figure 1) partially published in the work of [13] for various wind speeds ( U r e f = 2, 5, 7, 10, and 18 m s−1).
The Lagrangian Particle Tracking (LPT) model used by [9] for solid precipitation was modified by [24] to introduce drag coefficient equations suitable for liquid precipitation. These were derived for various ranges of the particle Reynolds number among those proposed in the literature by [7], and formulated starting from data published by [25,26]. Drop trajectories are computed from the particle motion equation, by calculating, at short time intervals, the particle position, velocity, and acceleration. The relative particle-to-air velocity is updated at every time step by interpolating the CFD airflow field to obtain the flow velocity in the exact position of the drop. Water drops are assumed to be spherical, with the associated equivalent diameter d, while the density of liquid water was set as equal to 1000 kg m−3 at the air temperature of 20 °C. This model was validated by means of a dedicated wind tunnel campaign in [24].
Starting from CFD simulations, the LPT model can obtain (per each particle size) the expected catch ratio, r (-), defined as the ratio between the number of particles, which are captured by the gauge collector in disturbed airflow conditions, n(d), and the maximum number of particles, nmax(d), captured in undisturbed conditions. Catch ratios were computed for drops with equivalent diameter d = 0.25, 0.5, and 0.75 mm and then from 1 to 8 mm, with bin size of 1 mm. These are compared in Table 1 and Figure 2 per each drop size and wind speed. For drop size less than 1 mm, the catch ratio increases with decreasing wind speed. For larger drops, the trend is not always growing, but increases and then decreases with increasing wind speed.
This behaviour is intrinsic in the balance between the drop size and the wind speed, and is graphically highlighted in Figure 3. In the graph, a grid is reported where the releasing positions of the simulated drops are depicted with black markers. Drops are released in the simulated airflow field, upstream of the gauge, at a higher elevation than the collector area, depending on the wind speed and drop diameter. The proper location was preliminarily calculated to ensure that the released drops eventually fall in the region occupied by the gauge. This was obtained by computing backward the trajectory of a sample drop which reaches the centre of the gauge collector in undisturbed airflow conditions. The collector’s rim is depicted with black circles and contains the starting positions of those particles that, in undisturbed conditions, would enter the gauge collector.
The drop-releasing positions are colour-coded according to their destination. The initial positions of all drops that in real conditions are expected to fall inside the gauge collector and are actually collected are depicted in red, while those falling inside the gauge collector but were expected to fall outside are depicted in green.
The left-hand panel of Figure 3 reports a low wind and/or heavy particle situation, and all drops that are expected to fall inside the collector in undisturbed conditions also reach the collector in the disturbed ones. A few additional drops, whose releasing positions are depicted in green, also enter the collector while being expected to fall outside. This implies an overestimation (r > 1) of the precipitation collected by the gauge, and therefore the resulting catch ratio is larger than one. By increasing the wind speed, or reducing the drop size, the wind field deformation reduces the number of particles depicted with red dots, and slightly increases the green ones (right-hand panel of Figure 3). In this sample case, the sum of the red and green dots is lower than the number of particles expected to fall inside the black circle, yielding an overall underestimation of the number of particles collected and r < 1.
After introducing a suitable PSD, indicating the number of particles N ( d ) per unit volume of air and per unit size interval having a volume equal to the sphere of diameter d , the integral of the catch ratios over the range of diameters provides the numerical CE in the form:
C E ( U r e f ) = 0 d ρ p   V p   n ( d )   N ( d )   d d 0 d ρ p   V p   n m a x ( d )   N ( d )   d d  
where ρ p ,   V p are the density and volume of particles with diameter d .
The CE curve was derived from the calculated catch ratios by assuming that the microphysical characteristics of precipitation are those obtained from distrometer measurements in the Italian territory. The PSDs, provided by [27] for various RI classes, were fitted with the typical exponential function [28], hereinafter MP), and the associated parameters N 0 (intercept) and Λ (slope) were adopted to calculate the CE values (here called raw CE values) per each RI class.
A three-step procedure was used to derive a suitable parameterization of the CE curves based on rainfall intensity (RI), as follows.
First, in step (a), for each RI class, the CE curve was obtained as a function of wind speed ( U r e f ) from the raw values of the numerical simulation results by fitting (with a least-squares method) a four-parameter sigmoidal function (CE = f( U r e f )—see Equation (10)) and using the experimental N 0 and Λ parameters associated with each RI class.
The parameters N 0 and Λ used in step (a), attributed to the mean value of each RI class, were then fitted in step (b) with power law curves as a function of RI, and a new sigmoidal CE curve was obtained per each RI class from the fitted parameters. The definition of N 0 and Λ as a function of RI has the advantage of obtaining the MP parameters for any RI value, within the range investigated. After calculating the CE values for the associated RI and U r e f , the CE curves could be obtained again as a sigmoidal best-fit.
Finally, in step (c), to obtain a simple formulation for the CE as a function of both RI and U r e f in the investigated ranges, the four parameters of the sigmoidal function were also fitted with power laws or logarithmic curves as a function of RI.
The procedure was applied to real-world observations. The average observed PSD measured by the Pludix distrometer in the Florence experimental site, as provided by [27], classified in six rainfall intensity classes, was adopted here and fitted using the typical MP exponential function, as shown in Figure 4. Some distrometers, including the Pludix, have limitations in detecting and counting small-size particles [27]. Other instruments show a drop in the number of particles below 1 mm, although it is not clear whether this feature is inherent of the precipitation process or is a measurement bias. The exponential behaviour is here extended below 1 mm, down to a diameter of 0.25 mm. In general, small particles (lower than 0.25 mm) give a rather negligible contribution to the total volume of precipitation.
The MP parameters N 0 (mm−1 m−3) and Λ (mm−1), and the correlation factors (R2) for each rainfall intensity class are listed in Table 2.
As expected, the parameter Λ decreases with increasing RI, while N 0 increases. This is due to the fact that heavy rainfall events are characterized by a relatively higher number of drops of large diameter in the distribution and by an overall higher number of particles in one cubic meter of air. Therefore, by increasing RI, the slope of the distribution decreases and the curve is displaced upward. For all RI classes, the correlation factor is larger than 0.97, yielding a very good fit between the MP exponential curves and observations.

3. Results

Following step (a), for each simulated wind speed ( U r e f ), the raw CE values were numerically calculated as reported in Equation (9), by using for the PSD the best-fit MP parameters associated with each RI class (from Table 2). Then, the obtained raw CE values (diamonds in Figure 5) were fitted with a four-parameter sigmoidal function (Equation (10) and dash-dot lines in Figure 5). The obtained parameters’ values are listed in Table 3 together with their associated R2.
C E ( U r e f ) = y 0 + a 1 + e   ( U r e f x 0 ) b  
Following step (b), with the objective of making the dependence of the collection efficiency on the RI explicit, the parameters N 0 and Λ were assigned to the mean value of each RI class and fitted with power law interpolation curves (Equation (11)), as shown in Figure 6.
Y ( R I ) = a Y   R I   b Y
In Equation (11), Y assumes the nomenclature of the PSD intercept N 0 and slope Λ, while a Y and b Y are the associated parameters of the best-fit power law curves. The values of the power law parameters are listed in Table 4, together with the correlation factors for both N 0 and Λ.
The CE values were calculated by adopting the N 0 and Λ values provided by the power law curves (Figure 6, dashed lines). The best-fit sigmoidal functions provide the new parameters for the CE, as listed in Table 5. The new CE curves are depicted in Figure 7 (dashed lines) and compared with the raw CE values (diamonds) calculated under step a). This further step provides an important advantage because it allows to derive the PSD for any desired rainfall intensity within the measured RI range (0.5–25 mm h−1).
Finally, as summarized in step (c), a general formulation for the CE Equation (12) as a function of both RI and U r e f , but independent of the initial RI classes and valid throughout the investigated RI range, was obtained by fitting the sigmoidal parameters associated with the mean value of each RI class with logarithmic (for b , x 0 , y 0 ) and power law (for the parameter a ) curves.
C E ( U r e f ) = y 0 ( R I ) + a ( R I ) 1 + e   ( U r e f x 0 ( R I ) ) b ( R I )
The best-fit curves for each sigmoidal parameter (a, b , x 0 and y 0 ) as a function of RI are listed below and shown in Figure 8 with the associated correlation factors.
a = 0.2213 RI−0.17
b = 0.1191 ln(RI) − 4.1365
x0 = 0.5222 ln(RI) + 4.4164
y0 = 0.0166 ln(RI) + 0.8645
To verify the quality of this result, the collection efficiency curves were calculated by using Equation (12) for the mean value of each RI class (Figure 7, continuous lines), as already done in steps a) and b). Then, the correlation between the raw CE values and the CE curves obtained in the three steps (a–c) was compared. Figure 9 shows the correlation factors for each RI class and the partial step adopted ((a–c)). This result reveals that, in all cases, the correlation factors are very high, larger than 0.99, and only slightly higher for step (a) than for step (c) (about +10−5). This very minimal worsening in performance is counterbalanced by the simplification introduced by the final CE curve, which allows the easy application of a correction factor for the wind-induced bias of operational precipitation measurements.
The derived numerical CE curve is a function of the actual rainfall intensity that, in this case, was obtained from the PSD provided by [27]. However, in operational practice, the only knowledge available for RI is that measured by the gauge, which is therefore affected by the wind-induced bias. In this work, the adjustment curve was further derived, for application purposes, as a direct relationship between the reference rainfall intensity (RI) and the measured one (RImeas), so that the actual rainfall intensity (and the wind-induced bias) can be calculated starting from the measurement provided by the gauge, once the wind velocity is known.
Recalling that, in the field, the CE is defined as the ratio between the precipitation measured by the gauge (RImeas) and the reference one (RI), it is possible to derive from Equation (12), the RImeas associated with each ( U r e f , RI) couple within the investigated range. The results can be depicted in the (RI, RImeas) plane for each wind speed, as shown in Figure 10. The RImeas values calculated from Equation (12) for the mean values of each RI class and the simulated wind speed are depicted with markers, while the associated adjustment curves were obtained as best-fit power law curves as follows:
R I m e a s = α ( U r e f ) R I β ( U r e f )
The coefficient α and exponent β of the adjustment curves for the simulated wind speed are summarized in Table 6, with a correlation factor (R2) equal to one (1.000) in all cases, and their functional dependency on wind speed is expressed in Equations (18) and (19). The correlation factor is equal to 0.973 and 0.997 for α and β, respectively.
α =   1.0621   U r e f 0.066
β   =   0.9971   U r e f 0.007
In Figure 10, the diagonal (continuous black line) indicates CE = 1, while the grey dashed lines correspond to CE values from 0.95 to 0.99. As expected, the adjustment curve for U r e f = 2 m s−1 is located above the diagonal, due to the overcatch observed at this low wind speed, while the other curves are lower due to the wind-induced undercatch. Moreover, the adjustment curves are described by power law functions, with coefficients (see Table 6) that are increasingly different from one (the linear case when CE is constant) as the wind speed increases, reflecting the trend towards higher values of CE while the rainfall intensity increases.
Although the deviation is small, it is possible to note in the graph that the adjustment curve at e.g., 18 m s−1 progressively diverges from the dashed line at CE = 0.96 with increasing rainfall intensity (towards the right-hand side of the graph), while they are practically superimposed to each other at a low RI (left-hand side of the graph). This means that, at any given wind speed, the collection efficiency varies with the rainfall intensity, rather than lying on a curve (line) at CE = constant, as predicted by the existing experimental studies (e.g., [14]).

4. Discussion

Adjustment curves for a typical, cylindrical gauge as a function of wind speed were derived from numerical simulation, including a new parameterization based on the measured rainfall intensity. A simple formulation of the adjustment curves was obtained, which can be easily applied in an operational context. Wind velocity is the only ancillary variable required to perform the adjustment and, since wind is often measured by operational weather stations together with the precipitation intensity, its use adds no relevant burden to the cost of meteo-hydrological networks.
The functional dependency of the CE curves on rainfall intensity is demonstrated in this work for a cylindrical, catching-type gauge and the results confirm that such a parameterization holds for liquid precipitation measurements, as was demonstrated already by [14] for snowfall measurements, using a chimney-shaped weighing gauge. Using RI as a controlling factor for the CE has sound physical bases in the relationship between RI and the PSD, and the role of RI can only be quantified using numerical simulations of both the airflow field (CFD) and the particle motion (LPT). Reference [14] also demonstrated that the application of this rationale to field test data helps in reducing the scatter of the observations. Further developments of the present work would include extensive validation with suitable experimental campaigns where contemporary RI and wind velocity data are available, together with a reference rain gauge pit. The role of free-stream turbulence in attenuating the updraft and acceleration of the airflow above the collector as shown in [29], and its effect on the adjustment curves could also be quantified.
Application of the results presented in this work spans over many fields of hydrology, meteorology, and climatology, including water resources and flood risk management and agriculture. Rainfall is indeed the forcing input of the land phase of the hydrological cycle. The knowledge of rainfall, its variability and the observed/expected patterns of rain events in space and time, are of paramount importance for most hydrological studies, and a large number of consequences of such studies on the engineering practice are exploited in the everyday technical operation. The results, especially the proposed adjustment curves, have the potential to improve rainfall measurements in order to support the enhanced accuracy and reliability of the basic information used in many engineering applications such as the design of hydraulic works, the protection from flood-related hazards, the management of potable water supply and its conservation, hydropower production, the enhancement of sustainability and resilience of human settlements and the conservation and protection of the natural and cultural heritage.

Author Contributions

Conceptualization, A.C.; methodology, A.C. and L.G.L.; supervision, L.G.L.; writing—original draft, A.C.; writing—review & editing, L.G.L. All authors have read and agreed to the published version of the manuscript.

Funding

This research was funded by the Italian MIUR (Ministero dell’Istruzione, dell’Università e della Ricerca), grant number PRIN20154WX5NA, project “Reconciling precipitation with runoff: the role of understated measurement biases in the modelling of hydrological processes”.

Acknowledgments

This work was developed as partial fulfilment of the PhD thesis of the first author.

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. Sevruk, B. Methods of Correction for Systematic Error in Point Precipitation Measurement for Operational Use; Tech. Rep. WMO N. 589, OHR N. 21; Secretariat of the World Meteorological Organization: Geneva, Switzerland, 1982; ISBN 978-92-63-10589-9. [Google Scholar]
  2. Legates, D.; Willmott, C. Mean seasonal and spatial variability in gauge-corrected, global precipitation. Int. J. Climatol. 1990, 10, 111–127. [Google Scholar] [CrossRef]
  3. WMO—World Meteorological Organization. Guide to Meteorological Instruments and Methods of Observation; WMO-N. 8 (Updated 2017); WMO: Geneva, Switzerland, 2014; ISBN 978-92-63-10008-5. [Google Scholar]
  4. Nešpor, V.; Sevruk, B. Estimation of wind-induced error of rainfall gauge measurements using a numerical simulation. J. Atmos. Ocean. Technol. 1999, 16, 450–464. [Google Scholar] [CrossRef]
  5. Jevons, W.S. On the deficiency of rain in an elevated rain-gauge, as caused by wind. Lond. Edinb. Dublin Philos. Mag. 1861, 21, 421–433. [Google Scholar] [CrossRef]
  6. Warnik, C.C. Experiments with windshields for precipitation gages. Eos 1953, 34, 379–388. [Google Scholar] [CrossRef]
  7. Folland, C.K. Numerical models of the raingauge exposure problem, field experiments and an improved collector design. Q. J. R. Meteorol. Soc. 1988, 114, 1485–1516. [Google Scholar] [CrossRef]
  8. Thériault, J.M.; Rasmussen, R.; Ikeda, K.; Landolt, S. Dependence of snow gauge collection efficiency on snowflake characteristics. J. Appl. Meteorol. Climatol. 2012, 51, 745–762. [Google Scholar] [CrossRef] [Green Version]
  9. Colli, M.; Lanza, L.G.; Rasmussen, R.; Thériault, J.M.; Baker, B.C.; Kochendorfer, J. An improved trajectory model to evaluate the collection performance of snow gauges. J. Appl. Meteorol. Climatol. 2015, 54, 1826–1836. [Google Scholar] [CrossRef] [Green Version]
  10. Cauteruccio, A.; Chinchella, E.; Stagnaro, M.; Lanza, L.G. Snow Particle Collection Efficiency and Adjustment Curves for the Hotplate© Precipitation Gauge. J. Hydrometeor. 2020. under review. [Google Scholar]
  11. Rasmussen, R.; Baker, B.; Kochendorfer, J.; Meyers, T.; Landolt, S.; Fischer, A.P.; Black, J.; Thériault, J.M.; Kucera, P.; Gochis, D.; et al. How well are we measuring snow: The NOAA/FAA/NCAR winter precipitation test bed. Bull. Amer. Meteor. Soc. 2012, 93, 811–829. [Google Scholar] [CrossRef] [Green Version]
  12. Pollock, M.D.; O’Donnell, G.; Quinn, P.; Dutton, M.; Black, A.; Wilkinson, M.E.; Colli, M.; Stagnaro, M.; Lanza, L.G.; Lewis, E.; et al. Quantifying and mitigating wind-induced undercatch in rainfall measurements. Water Resour. Res. 2018, 54, 3863–3875. [Google Scholar] [CrossRef]
  13. Colli, M.; Pollock, M.; Stagnaro, M.; Lanza, L.G.; Dutton, M.; O’Connell, P.E. A Computational Fluid-Dynamics assessment of the improved performance of aerodynamic raingauges. Water Resour. Res. 2018, 54, 779–796. [Google Scholar] [CrossRef]
  14. Colli, M.; Stagnaro, M.; Theriault, J.M.; Lanza, L.G.; Rasmussen, R. Adjustments for Wind- Induced Undercatch in Snowfall Measurements based on Precipitation Intensity. J. Hydrometeor. 2020, 21, 1039–1050. [Google Scholar] [CrossRef] [Green Version]
  15. Wolff, M.A.; Isaksen, K.; Petersen-Øverleir, A.; Ødemark, K.; Reitan, T.; Brækkan, R. Derivation of a new continuous adjustment function for correcting wind-induced loss of solid precipitation: Results of a Norwegian field study. Hydrol. Earth Syst. Sci. 2015, 19, 951–967. [Google Scholar] [CrossRef]
  16. Pruppacher, H.R.; Klett, J.D. Microphysics of Clouds and Precipitation. In Atmospheric and Oceanographic Sciences Library; Springer: Dordrecht, The Netherlands, 2010; 954p. [Google Scholar] [CrossRef]
  17. EN 13798: 2010. Hydrometry—Specifications for a Reference Raingauge Pit; CEN/TC 318—Hydrometry; European Committee for Standardization: Brussels, Belgium, 2010.
  18. Goodison, B.E.; Louie, P.Y.T.; Yang, D. WMO Solid Precipitation Measurement Intercomparison; IOM Rep. No. 67 and WMO/TD No. 872; WMO: Geneva, Switzerland, 1998; 318p, Available online: http://www.wmo.int/pages/prog/www/reports/WMOtd872.pdf (accessed on 5 December 2020).
  19. Thériault, J.M.; Rasmussen, R.; Petro, E.; Trépanier, J.Y.; Colli, M.; Lanza, L.G. Impact of wind direction, wind speed, and particle characteristics on the collection efficiency of the double fence intercomparison reference. J. Appl. Meteor. Climatol. 2015, 54, 1918–1930. [Google Scholar] [CrossRef] [Green Version]
  20. Sims, E.M.; Liu, G. A parameterization of the probability of snow–rain transition. J. Hydrometeor. 2015, 16, 1466–1477. [Google Scholar] [CrossRef]
  21. Kochendorfer, J.; Rasmussen, R.; Wolff, M.; Baker, B.; Hall, M.E.; Meyers, T.; Landolt, S.; Jachcik, A.; Isaksen, K.; Brækkan, R.; et al. The quantification and correction of wind-induced precipitation measurement errors. Hydrol. Earth Syst. Sci. 2017, 21, 1973–1989. [Google Scholar] [CrossRef] [Green Version]
  22. Kochendorfer, J.; Nitu, R.; Wolff, M.; Mekis, E.; Rasmussen, R.; Baker, B.; Earle, M.E.; Reverdin, A.; Wong, K.; Smith, C.D.; et al. Analysis of single-Alter-shielded and unshielded measurements of mixed and solid precipitation from WMOSPICE. Hydrol. Earth Syst. Sci. 2017, 21, 3525–3542. [Google Scholar] [CrossRef] [Green Version]
  23. Buisán, S.T.; Earle, M.E.; Collado, J.L.; Kochendorfer, J.; Alastrué, J.; Wolff, M.; Smith, C.D.; López-Moreno, J.I. Assessment of snowfall accumulation underestimation by tipping bucket gauges in the Spanish operational network. Atmos. Meas. Tech. 2017, 10, 1079–1091. [Google Scholar] [CrossRef] [Green Version]
  24. Cauteruccio, A.; Brambilla, E.; Stagnaro, M.; Lanza, L.G.; Rocchi, D. Wind Tunnel Validation of a Particle Tracking Model to Evaluate the Wind-Induced Bias of Precipitation Measurements. Water Resour. Res. 2020. under review. [Google Scholar]
  25. Beard, K.V. Terminal velocity and shape of cloud and precipitation drops aloft. J. Atmos. Sci. 1976, 33, 851–864. [Google Scholar] [CrossRef] [Green Version]
  26. Khvorostyanov, V.I.; Curry, J.A. Fall Velocities of Hydrometeors in the Atmosphere: Refinements to a Continuous Analytical Power Law. J. Atmos. Sci. 2005, 62, 4343–4357. [Google Scholar] [CrossRef]
  27. Caracciolo, C.; Porcù, F.; Prodi, F. Precipitation classification at mid-latitudes in terms of drop size distribution parameter. Adv. Geosci. 2008, 16, 11–17. [Google Scholar] [CrossRef] [Green Version]
  28. Marshall, J.S.; Palmer, W.M.K. The distribution of raindrops with size. J. Meteorol. 1948, 5, 165–166. [Google Scholar] [CrossRef]
  29. Cauteruccio, A.; Colli, M.; Freda, A.; Stagnaro, M.; Lanza, L.G. The role of free-stream turbulence in attenuating the wind updraft above the collector of precipitation gauges. J. Atmos. Ocean. Technol. 2020, 37, 103–113. [Google Scholar] [CrossRef]
Figure 1. (a) The Casella tipping-bucket rain gauge; (b) a sample section of the airflow field (velocity magnitude, Um (m s-1)) along the stream-wise vertical symmetry axis of the gauge at wind speed of 10 m s−1 (from CFD simulations by [13]).
Figure 1. (a) The Casella tipping-bucket rain gauge; (b) a sample section of the airflow field (velocity magnitude, Um (m s-1)) along the stream-wise vertical symmetry axis of the gauge at wind speed of 10 m s−1 (from CFD simulations by [13]).
Water 12 03431 g001
Figure 2. Catch ratios per each drop size, resulting from the LPT model run at different wind speed and based on the airflow fields simulated for the Casella cylindrical rain gauge.
Figure 2. Catch ratios per each drop size, resulting from the LPT model run at different wind speed and based on the airflow fields simulated for the Casella cylindrical rain gauge.
Water 12 03431 g002
Figure 3. Schematics of the initial positions of the modelled trajectories, colour-coded according to their destination, and projection of the collector’s rim (black circles). Red dots indicate drops that actually fall inside the gauge collector in real conditions and that were expected to do so, while green dots indicate those falling inside the gauge collector instead of outside. (a) Low wind and/or heavy particles; (b) strong wind and/or light particles.
Figure 3. Schematics of the initial positions of the modelled trajectories, colour-coded according to their destination, and projection of the collector’s rim (black circles). Red dots indicate drops that actually fall inside the gauge collector in real conditions and that were expected to do so, while green dots indicate those falling inside the gauge collector instead of outside. (a) Low wind and/or heavy particles; (b) strong wind and/or light particles.
Water 12 03431 g003
Figure 4. Measured PSD data from [27] and the associated best-fit exponential functions obtained for each rainfall intensity class.
Figure 4. Measured PSD data from [27] and the associated best-fit exponential functions obtained for each rainfall intensity class.
Water 12 03431 g004
Figure 5. Raw CE values (diamonds) obtained by using the parameters derived from the MP exponential interpolation function, for each RI class, and the associated sigmoidal functions (dash-dot lines).
Figure 5. Raw CE values (diamonds) obtained by using the parameters derived from the MP exponential interpolation function, for each RI class, and the associated sigmoidal functions (dash-dot lines).
Water 12 03431 g005
Figure 6. MP parameters associated with the mean values of each RI class (circles) and fitted by power law curves (dashed lines), (a) intercept N 0 and (b) exponent Λ.
Figure 6. MP parameters associated with the mean values of each RI class (circles) and fitted by power law curves (dashed lines), (a) intercept N 0 and (b) exponent Λ.
Water 12 03431 g006
Figure 7. Raw CE values (diamonds) obtained by using the MP parameters derived from the exponential interpolation in step (a), for each RI class, and CE curves obtained by expressing N 0 and Λ as a function of RI (dashed lines) in step (b) and by expressing the sigmoidal parameters as a function of RI (continuous lines) in step (c).
Figure 7. Raw CE values (diamonds) obtained by using the MP parameters derived from the exponential interpolation in step (a), for each RI class, and CE curves obtained by expressing N 0 and Λ as a function of RI (dashed lines) in step (b) and by expressing the sigmoidal parameters as a function of RI (continuous lines) in step (c).
Water 12 03431 g007
Figure 8. Sigmoidal parameters associated with the mean value of each RI class (circles) and fitted by either power law or logarithmic curves (dashed lines) (a) parameter a; (b) parameter b, (c) parameter x0; (d) parameter y0.
Figure 8. Sigmoidal parameters associated with the mean value of each RI class (circles) and fitted by either power law or logarithmic curves (dashed lines) (a) parameter a; (b) parameter b, (c) parameter x0; (d) parameter y0.
Water 12 03431 g008
Figure 9. Correlation factors between the raw CE values and the CE curves obtained, for each RI class, under step (a) (blue), (b) (orange) and (c) (grey).
Figure 9. Correlation factors between the raw CE values and the CE curves obtained, for each RI class, under step (a) (blue), (b) (orange) and (c) (grey).
Water 12 03431 g009
Figure 10. Adjustment curves (dotted lines) for the Casella cylindrical gauge and linear curves at constant CE values (dashed lines). Circles indicate the results of the performed numerical simulations and are colour-coded according to the wind speed ( U r e f ) .
Figure 10. Adjustment curves (dotted lines) for the Casella cylindrical gauge and linear curves at constant CE values (dashed lines). Circles indicate the results of the performed numerical simulations and are colour-coded according to the wind speed ( U r e f ) .
Water 12 03431 g010
Table 1. Catch ratios for each drop size and at different wind speed, calculated by means of the LPT model and based on the airflow field simulated for the Casella cylindrical rain gauge.
Table 1. Catch ratios for each drop size and at different wind speed, calculated by means of the LPT model and based on the airflow field simulated for the Casella cylindrical rain gauge.
d (mm)
U r e f ( m   s 1 )
0.250.50.7512345678
20.7910.9831.0101.0191.0171.0101.0101.0101.0101.0101.010
50.3560.9270.9771.0061.0231.0211.0171.0141.0101.0101.010
70.1100.8030.9380.9811.0101.0211.0211.0211.0171.0171.017
100.0850.7520.9270.9631.0061.0171.0211.0211.0211.0171.013
180.0150.6600.8680.9380.9921.0061.0141.0171.0211.0211.021
Table 2. Parameters N 0 and Λ of the MP distribution and the associated correlation factors for each rainfall intensity class, as obtained by fitting the measured PSD data provided by [27].
Table 2. Parameters N 0 and Λ of the MP distribution and the associated correlation factors for each rainfall intensity class, as obtained by fitting the measured PSD data provided by [27].
RI Range (mm h−1)RI ≤ 11 < RI ≤ 22 < RI ≤ 55 < RI ≤ 1010 < RI ≤ 20RI > 20
N 0 (mm h−1 m−3)365.11692.82775.04459.06989.418370.0
Λ (mm−1)3.5613.1342.9142.7712.7232.609
R20.9790.9760.9790.9750.9720.979
Table 3. Parameters of the sigmoidal functions obtained by fitting the raw CE values derived by using the MP parameters from the exponential interpolations and correlation factors for each RI class.
Table 3. Parameters of the sigmoidal functions obtained by fitting the raw CE values derived by using the MP parameters from the exponential interpolations and correlation factors for each RI class.
RI Range (mm h−1)RI ≤ 11 < RI ≤ 22 < RI ≤ 55 < RI ≤ 1010 < RI ≤ 20RI > 20
a 0.2632−0.19950.16960.15130.14540.1317
b −4.24954.0670−3.9526−3.8710−3.8422−3.7713
x 0 3.84294.75125.25105.59145.70905.9960
y 0 0.84451.07530.89200.90240.90580.9140
R20.9840.9840.9830.9820.9820.982
Table 4. Best-fit parameters a Y and b Y (Equation (11)) for both N 0 and Λ, expressed as a function of RI, and the associated correlation factors.
Table 4. Best-fit parameters a Y and b Y (Equation (11)) for both N 0 and Λ, expressed as a function of RI, and the associated correlation factors.
N 0 ( mm   h 1   m 3 ) Λ (mm−1)
a Y 835.913.2863
b Y 0.8942−0.0760
R20.9640.962
Table 5. Parameters of the sigmoidal functions obtained by using N 0 ( R I ) and Λ(RI) as power law curves and the associated correlation factors for each RI class.
Table 5. Parameters of the sigmoidal functions obtained by using N 0 ( R I ) and Λ(RI) as power law curves and the associated correlation factors for each RI class.
RI Range (mm h−1)RI ≤ 11 < RI ≤ 22 < RI ≤ 55 < RI ≤ 1010 < RI ≤ 20RI > 20
a 0.24810.20690.17940.15740.13950.1275
b −0.2127−4.0923−3.9925−3.8994−3.8128−0.7481
x 0 4.0434.63535.08035.47395.82846.0888
y 0 0.85160.8720.88660.89880.90930.9165
R20.9840.9840.9830.9830.9820.981
Table 6. Parameters α and β of the power law best-fit curves at different wind speeds ( U r e f ).
Table 6. Parameters α and β of the power law best-fit curves at different wind speeds ( U r e f ).
U r e f ( m   s 1 ) 2571018
α1.00570.96680.94130.90990.8726
β1.00231.00761.01061.01381.0175
Publisher’s Note: MDPI stays neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Share and Cite

MDPI and ACS Style

Cauteruccio, A.; Lanza, L.G. Parameterization of the Collection Efficiency of a Cylindrical Catching-Type Rain Gauge Based on Rainfall Intensity. Water 2020, 12, 3431. https://doi.org/10.3390/w12123431

AMA Style

Cauteruccio A, Lanza LG. Parameterization of the Collection Efficiency of a Cylindrical Catching-Type Rain Gauge Based on Rainfall Intensity. Water. 2020; 12(12):3431. https://doi.org/10.3390/w12123431

Chicago/Turabian Style

Cauteruccio, Arianna, and Luca G. Lanza. 2020. "Parameterization of the Collection Efficiency of a Cylindrical Catching-Type Rain Gauge Based on Rainfall Intensity" Water 12, no. 12: 3431. https://doi.org/10.3390/w12123431

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop