Experimental Study of Overland Flow through Rigid Emergent Vegetation with Different Densities and Location Arrangements

The effect of vegetation density on overland flow dynamics has been extensively studied, yet fewer investigations have focused on vegetation arrangements with different densities and position features. Flume experiments were conducted to investigate the hydrodynamics of flow through rigid emergent vegetation arranged in combinations with three densities (Dense, Middle, and Sparse) and three positions (summit, backslope, and footslope). This study focused on how spatial variations regulated hydrodynamic parameters from two dimensions: direction along the slope and water depth. The total hydrodynamic parameters of bare slopes were significantly different from those of vegetated slopes. The relationship between Re and f illustrated that Re was not a unique predictor of hydraulic roughness on vegetated slopes. In the slope direction, all hydrodynamic parameters on vegetated slopes exhibited fluctuating downward/upward trends due to the clocking effect before the vegetated area and the rapid conveyance effect in the vegetated area, whereas constant values were observed on bare slopes. The performance of hydrodynamics parameters suggested that the dense rearward arrangement (SMD) was the optimal vegetation pattern to regulate flow conditions. Specifically, the vertical profiles of the velocity and turbulence features of the SMD arrangement at different sections demonstrated the significant role of vegetation density in identifying the velocity layers along the water depth. The maximum velocity and Reynolds Stress Number (RSN) indicated the position where local scour was most likely to occur, which would improve our basic understanding of the mechanisms underlying hydraulic and soil erosion processes.


Introduction
Overland flow passing through vegetation on hillslopes has been extensively studied, both experimentally and numerically, due to its remarkable roles in the transportation of nutrients, contaminants, and sediment loads [1][2][3]; therefore, this factor is widely used in soil erosion control and stream ecological restoration [4]. Arbor and shrub tress, which are usually arranged in strip, patch and block patterns [5], can effectively control erosion on hill slopes. In terms of altering flow hydrodynamic characteristics, such as by increasing local roughness, modifying flow pattern, providing additional resistance and decreasing bed shear stress, etc. The existence of such rigid and emergent (usually discontinued and uneven planted) vegetation alters the velocity distribution and flow dynamics.

Experimental Setup
The experiment was conducted in a closed-loop open surface recirculating rectangular flume, with dimension of 12.5 m × 0.3 m × 0.3 m, at the Mechanism and Process of Gully Erosion Laboratory, the School of Soil and Water Conservation, Beijing Forestry University, China. A schematic sketch of the experimental setup and measuring instruments for test sections were shown in Figure 1. The water flow was pumped and controlled by a frequency water pump, and measured by an electromagnetic flow-meter installed in the entrance of the flume system, where a series of honeycombs was mounted to straighten the inflow and avoid large-scale disturbances. A tail gate was installed at the export of the flume to ensure the steady uniform state of the outflow. The experimental section was 3 m downstream from the entrance to establish a fully developed flow regime, and the length of the observation section was 7 m, where the simulated vegetation was fixed in a strip pattern. The Acoustic Doppler Velocimeter (ADV) and micrometer were adopted to observe the velocity and water depth, which could be moved in the longitudinal direction. Because positive and gentle slopes are commonly found in natural overland flows, the bed slope of the flume was set to a constant value of 1‰. This slope could ensure the steady flow state and avoid the breakage caused by steep slope [27]. The average flow rates were set to 0.8 L/s, 1.5 L/s, 1.9 L/s, 2.3 L/s, 2.9 L/s, 3.3 L/s, and 3.8 L/s to investigate the dynamic characteristics of overland flow with various inflow rates. The discharges were enveloped with a range within which the flow depth was constrained in a shallow overland flow condition, and the flow state could cover multiple zones [27,28]. The water temperature was monitored throughout the experimental process by a thermometer. The configurations were given in Section 2.2. In this experiment, the smallest breadth depth ratio was 5.7, under this kind of water depth state, the flow was quasi-two-dimensional flow [29], so that the effect of the side wall could be neglected.

Vegetation Material and Configurations
Artificial plants made of polyvinyl chloride (PVC) pipes with an outer diameter d = 1 cm and height hr = 10 cm were used in this study to simulate rigid unsubmerged vegetation. The cylinders were arranged in a staggered pattern to form regular triangles (Figure 2a). Three different vegetation densities (Sparse (1%), Middle (2%), and Dense (4%)) were selected, which were defined by the ratio of the bottom areas of all stems to that of the flume area for the vegetated section with the given equation:

Vegetation Material and Configurations
Artificial plants made of polyvinyl chloride (PVC) pipes with an outer diameter d = 1 cm and height h r = 10 cm were used in this study to simulate rigid unsubmerged vegetation. The cylinders were arranged in a staggered pattern to form regular triangles (Figure 2a). Three different vegetation densities (Sparse (1%), Middle (2%), and Dense (4%)) were selected, which were defined by the ratio of the bottom areas of all stems to that of the flume area for the vegetated section with the given equation: where L is the length of the test section (1 m in this study), B is the flume width (30 cm in this study), a is the distance between two stems in the lateral direction (m), b is the distance between two stems in the longitudinal section (m), and d is the diameter of cylinder (m).
where L is the length of the test section (1 m in this study), B is the flume width (30 cm in this study), a is the distance between two stems in the lateral direction (m), b is the distance between two stems in the longitudinal section (m), and d is the diameter of cylinder (m). As the vegetated and non-vegetated testing areas were alternatively mounted in 1 m intervals and with 1 m vegetated sections, a total of six arrangements were oriented along the summit, backslope and footslope as shown in Figure Table 1 (a) (b)   As the vegetated and non-vegetated testing areas were alternatively mounted in 1 m intervals and with 1 m vegetated sections, a total of six arrangements were oriented along the summit, backslope and footslope as shown in Figure 2b Table 1.

Locations of Flow Measurements
To obtain reliable and accurate results, the water depths were measured at three longitudinal sections in this experiment with 1 mm measuring accuracy. These longitudinal sections were located 15 cm, 7.5 cm, and 0 cm away from one side wall and named LS1, LS2, and LS3, respectively. On these longitudinal sections, measurement points were established at 25 cm intervals along the test section, with an increase in the number of observation points at the outflow section (S25, S26, and S27) ( Figure 3a). In the direction of the vertical profile (Figure 3c), the flow velocities were measured every 0.4 cm by ADV from the bottom to the water surface ( Figure 3c). Due to instrument limitations, flows within 2.5 cm from surface could not be detected. Note that the number of measurement points in each section differed, due to the differences in water depth. The ADV has three acoustic receivers and one acoustic transmitter, and it provides water velocity measurements in three directions: the longitudinal component (u), the transverse component (v), and the vertical component (w). In previous studies [30], the mean flow velocity stabilized when the measurement duration was greater than 45 s. Thus, the test time of the flow velocity measurement time was set to 60 s with a 6000 sampling number at 100 Hz, and the sampling volume was 7 × 10 −2 m 3 . The distance from the probe to the measurement point was 2.4 × 10 −6 m. To ensure the quality of the measurement data, the signal-to-noise ratio of the measurements was maintained a 15 dB [31]. The average velocity at each point was calculated from the observations of 3000 samples. The observations were performed between two rows of simulated vegetation stems to eliminate the impact of acute changes in the simulated vegetation section as much as possible.

Parameter Determination
(1) Mean velocity Mean velocity is an important hydrodynamic parameter, and it is also the major index indicating flow intensity. The mean flow velocity was calculated from the mean flow depth using the following equation: where u is the mean flow velocity of a certain cross section, and h is the mean of the measured flow depths (m). In addition, the unit flow discharge (m 3 ·s −1 ·m −1 ) is represented by is the flow discharge ( L/s ).
(2) Flow-state indicator When the flow is stable, the flow-state indicator can be calculated as follows [32]: where m is the flow-state indicator, which indicates the magnitude of energy consumption, the larger the m, the more energy of the water flow is consumed by resistance; and k is a comprehensive index associated with the different arrangements, and it reflects the bed surface characteristics and flow viscosity. A larger interaction force of surface matter corresponds to a stronger effect of surface matter on the water flow across the slope.
(3) Reynolds number The Re is a dimensionless number that is used to define flow regimes. The Re on vegetated slopes could be calculated using the following equation:

Parameter Determination
(1) Mean velocity Mean velocity is an important hydrodynamic parameter, and it is also the major index indicating flow intensity. The mean flow velocity was calculated from the mean flow depth using the following equation: where u is the mean flow velocity of a certain cross section, and h is the mean of the measured flow depths (m). In addition, the unit flow discharge (m 3 ·s −1 ·m −1 ) is represented by q = Q/B, where Q is the flow discharge (L/s).
(2) Flow-state indicator When the flow is stable, the flow-state indicator can be calculated as follows [32]: where m is the flow-state indicator, which indicates the magnitude of energy consumption, the larger the m, the more energy of the water flow is consumed by resistance; and k is a comprehensive index associated with the different arrangements, and it reflects the bed surface characteristics and flow viscosity. A larger interaction force of surface matter corresponds to a stronger effect of surface matter on the water flow across the slope.
(3) Reynolds number The Re is a dimensionless number that is used to define flow regimes. The Re on vegetated slopes could be calculated using the following equation: Bare slope: Vegetated slope: where the direct factor R = Bh/P is the hydraulic radius (m), and P is the wetted perimeter. Equations (5) and (6) are for non-vegetated and vegetated slopes, respectively. In addition, m 1 is the number of stems of each cross section, and v is the kinematic viscosity of clear water (cm 2 ·s −1 ), which is calculated as v = 0.01775/(1 + 0.0337t + 0.000221t 2 ), and t is the flow temperature ( • C).
(4) Froude number The mechanical definition of the Froude number (Fr) is the contrast relation between the inertial force and gravity, and it is the critical value characterizing the water flow pattern. A sub-critical flow occurs when Fr < 1, and super-critical flow occurs when Fr > 1. The Fr be calculated as follows: where g is the acceleration of gravity.
(5) Total energy The total energy for each longitudinal section can be calculated using the following energy equation: In the present study, the channel bed at the end of vegetation section is considered as the datum plane; z is the vertical distance of the channel bed from the datum plane; and α is the correction factor, and it was equal to 1 in the present research. The flow resistance in present study was calculated using the method of Hessel [33]. The resistance coefficient is calculated as follows: where J is the hydraulic gradient. In this paper, the value of the hydraulic gradient was replaced by the sinusoidal value of the slope, which is 1 .

(7) Manning coefficient
The Manning coefficient is related to the vegetation density and flow velocity. The general equation for the Manning coefficient is as follows: where n is the Manning coefficient. This formula is applicable for non-vegetated conditions, and Noarayanan et al. [34] modified this equation for vegetated conditions using rigid tubes to mimic plants. The modified equation was also used in Li's paper [35]: where n veg is the Manning coefficient with vegetation only; u veg+wall is the velocity measured with vegetation section. u wall is the velocity measured without vegetation. u u(wall) is the upstream velocity measured without vegetation. u d(wall) is the downstream velocity measured without vegetation. h u(wall) is the depth of flow at the downstream location without vegetation, h d(wall) is the depth of flow at the downstream without vegetation. H f(wall) is the head loss due to side and bottom wall; S veg+wall is the energy slope in the presence of vegetation; S wall is the energy slope without vegetation.

(8) Turbulence intensity
The turbulence intensity was calculated using the following equations: where N is the total number of velocities obtained; u i , v i , and w i represent the stream-wise velocity, span-wise velocity and vertical velocity, respectively; and u, v, w represent the mean velocities in the three directions.
(9) Reynolds stress number To determine the effects of the different vegetation densities on the Reynolds stress profile, the Reynolds stress number (RSN) was calculated using the following equation:

Flow Velocity and Flow State
Both the mean velocities u and Re increased with the increases of the flow discharge (0.01 < P u < 0.05, 0.01 < P Re < 0.05, where P u and P Re values are the significant levels of the Pettitt test) (Figure 4a,b). The u, Re, and Fr values on the bare slope were roughly twice as large as that on the vegetated slopes. In addition, a power relationship was observed between the u and flow discharge on both bare and vegetated slopes, according to the regression analysis (Table 2), and similar relationships have widely been reported in previous studies [36,37]. The Fr number and Darcy-Weisbach coefficient f on vegetated and non-vegetated slopes were quite different (Figure 4c,d). The flow on the bare slope was super-critical (Fr = 1.2) but sub-critical on vegetated slopes, which presented Fr values ranging from 0.4 to 0.6. The Fr ranked from lowest to highest was as follows: SMD < MSD < SDM < DSM < MDS < DMS. The smaller the Re and Fr were, the more stable the flow state would be, and the erosion on the underlying surface would be possibly smaller. Theoretically, during actual runoff process, the vegetation stems could potentially increase the infiltration and reduce the runoff and then weaken the soil erosion. As the observation was conducted under the same slope value (1 ), these results were reasonable and applicable for gentle slope.

Configurations Regression Equation
To better describe the flow patterns, the flow-state indicator was calculated using Equation (3). As shown in Table 3, the m value of 0.4559 on the bare slope indicates that the flow energy was mainly kinetic energy. The m values on the vegetated slopes were comparably larger, with a ranking of SMD > MSD > SDM > DSM > MDS > DMS > Bare. The m values for all vegetated slopes were greater than 0.5, suggesting that the energy was dominantly consumed against flow resistance; moreover, energy that could be converted to kinetic energy was a supplementary component [33]. The k values showed no obvious variation pattern, which may because this value was influenced by multiple factors [38].    To better describe the flow patterns, the flow-state indicator was calculated using Equation (3). As shown in Table 3, the m value of 0.4559 on the bare slope indicates that the flow energy was mainly kinetic energy. The m values on the vegetated slopes were comparably larger, with a ranking of SMD > MSD > SDM > DSM > MDS > DMS > Bare. The m values for all vegetated slopes were greater than 0.5, suggesting that the energy was dominantly consumed against flow resistance; moreover, energy that could be converted to kinetic energy was a supplementary component [33]. The k values showed no obvious variation pattern, which may because this value was influenced by multiple factors [38].

Darcy-Weisbach Friction Coefficient
In general, the f value for different vegetation patterns differed significantly (Figure 4d). For the six density arrangements, the f values were ranked as follows: SMD > MSD > SDM > DSM > MDS > DMS. This result indicated that the SMD pattern had the largest resistance coefficient. Our findings demonstrated that vegetation with greater density at the footslope position was more effective at reducing the dynamics of overland flow than the other configurations. The result was consistent with previous studies [39,40], which indicated that high vegetation densities at the footslope position were capable of resisting more accumulated momentum from the upslope areas. However, runoff flow at the footslope position were more likely to occur, due to the more significant changes in momentum coefficient [13].

Relationships between Re and f
A power law function between Re and f was found on the bare slope ( Figure 5), which had been demonstrated in previous studies [41]. Separate regression equations for f versus Re for all vegetated slopes were derived and shown in Table 4. For vegetated slopes, only the f-Re relation of the DMS configuration exhibited a similar law as that of the bare slope. Figure 5 demonstrates that the curve of the resistance coefficient was almost parallel to the horizontal axis, and the f values changed indistinctly. Al Hamdan et al. [42] also found that f and Re did not show a consistent or single monotonic relationship on vegetated slopes, the variation in f with Re was much less pronounced, and the relationship between these two parameters became increasingly weaker. The overall result suggests that Re was not a consistent and unique predictor of hydraulic roughness on vegetated slopes.

Darcy-Weisbach Friction Coefficient
In general, the f value for different vegetation patterns differed significantly (Figure 4d). For the six density arrangements, the f values were ranked as follows: SMD > MSD > SDM > DSM > MDS > DMS. This result indicated that the SMD pattern had the largest resistance coefficient. Our findings demonstrated that vegetation with greater density at the footslope position was more effective at reducing the dynamics of overland flow than the other configurations. The result was consistent with previous studies [39,40], which indicated that high vegetation densities at the footslope position were capable of resisting more accumulated momentum from the upslope areas. However, runoff flow at the footslope position were more likely to occur, due to the more significant changes in momentum coefficient [13].

Relationships between Re and f
A power law function between Re and f was found on the bare slope ( Figure 5), which had been demonstrated in previous studies [41]. Separate regression equations for f versus Re for all vegetated slopes were derived and shown in Table 4. For vegetated slopes, only the f-Re relation of the DMS configuration exhibited a similar law as that of the bare slope. Figure 5 demonstrates that the curve of the resistance coefficient was almost parallel to the horizontal axis, and the f values changed indistinctly. Al Hamdan et al. [42] also found that f and Re did not show a consistent or single monotonic relationship on vegetated slopes, the variation in f with Re was much less pronounced, and the relationship between these two parameters became increasingly weaker. The overall result suggests that Re was not a consistent and unique predictor of hydraulic roughness on vegetated slopes.

Longitudinal Hydrodynamics under Different Vegetation Configurations
The features of hydrodynamic parameters along the flume were further investigated. As the regularity of all results for different inflow discharges were quite similar, we only enumerated one group of results at a constant discharge of 3.8 L/s.

Water Depth, Mean Velocity, and Total Energy
As shown in Figure 6a, the water depth h, which represented an average of the values of the three longitudinal sections, on the bare slope was generally lower than that on the vegetated slope. Zhang et al. [9] also found the same result. Throughout the tested sections, the difference of h between the starting and ending sections for the six vegetated configurations was ranked as SMD < MSD < SDM < DSM < MDS < DMS. This result indicated that a dense rearward arrangement led to a smaller change in h and to a better water-blocking effect in the test section. Furthermore, increasing and decreasing trends were found for the non-vegetated and vegetated sections, respectively, demonstrating a blocking effect before the vegetated area and rapid conveyance effect in the vegetated area. Accordingly, in each vegetation section, the h increased and reached its peak value nearly 0.25 m after entering the vegetated section, and it subsequently decreased. After the S27 cross section, the water depth sharply decreased, and h varied in the order of DMS < MDS < DSM < SDM < MSD < SMD. Because of the water blocking of the backside vegetation section, the water depth gradually increased before the vegetation section, and denser vegetation at the rear of the order corresponded to a better accumulation effect of vegetation on water blocking. Correspondingly, the u of the bare slope was generally larger than that of the vegetated slopes before section S27 (Figure 6b), and similar results were also found in previous studies [11,23]. The mean velocities on the vegetated slopes ranked from lowest to highest, as follows SMD < MSD < SDM < DSM < MDS < DMS. This result indicated that the dense rearward arrangement helped to reduce the mean velocity, which potentially reduced the distance and the amount of sediment transport [43]. Therefore, flow velocity was proved to be a dominating parameter in the research of slope hydrological processes, which would further affect soil erosion and sediment transportation [44,45]. Due to the reverse relationship between h and u (Equation (2)), decreasing and increasing trends were found at the vegetated and unvegetated sections, respectively.
The total energy (E) for each longitudinal location was calculated to evaluate the energy dissipating processes (Figure 6c). On the vegetated slopes, the E showed a fluctuating downward trend, whereas on the bare slopes, the E was mostly stable, and this parameter could be ranked as SMD > MSD > SDM > DSM > MDS > DMS > Bare. The decreasing trend on vegetated slopes indicated that the presence of plants enhanced the dissipation of the E. Prior to S27, the experimental arrangements could be ordered according to the fluctuating E value: SMD < MSD < SDM < DSM < MDS < DMS. For the vegetated and bare slopes, the E flow tended to converge at the end of S27, where the effect of vegetation on E disappeared.
The profiles of the E (Figure 6c) was consistent in terms of the tendency of the water surface profiles (Figure 6a). The cross-section specific energy curve (Figure 6d) demonstrated positive linear relationships between the specific energy and the water depth (Figure 6d), indicating subcritical flow states. In the experiment, a distance was observed between the cross section-specific energy and 1:1 line. The distance from the potential energy trend line (red line) represents the proportion of potential energy in the E. A greater deviation of the red line indicates a lower percentage of the potential. Therefore, Figure 6d showed that the primary component of E was potential energy, and that the proportion of potential energy was ranked as follows: SMD < MSD < SDM < DSM < MDS < DSM. Huang et al. [46] and Schutten et al. [47] reported that the cross-section-specific energy in rigid vegetation channels increased with the increasing of water depth, and it tended to be a straight line with a 45 degree angle to the horizontal level.

Reynolds Number and Froude Number
The Re values along the flow direction ranged from 4400 to 11,200, which corresponded to transitional and turbulent flow regimes (Figure 7a). Wang et al. [6] also found that overland flow began with transitional flow at the top of a given slope, and finished with turbulent flow on the bottom. The comparably smaller Re values on vegetated slopes than that of the bare slope indicated less intense turbulent characteristics. In addition, on vegetated slopes, the Re values at vegetated sections (4000-6000) were much smaller than those of nonvegetated sections (8000-10,000). Previous studies also found that the turbulent intensity would decrease further with the increase in vegetation coverage [18,48]. Moreover, Zhao et al. [23] found that increasing vegetation cover was crucial to reducing soil loss. A decrease in Re meant a decrease in the flow turbulence and erosion force, and it resulted in a further reduction of soil loss. Moreover, the Re increased sharply directly after the flow exited the vegetated sections, which was mainly because vegetation not only reduced the energy and dispersed runoff, but also increased the surface roughness. Thus, vegetation played an important role in delaying the flow velocity over slopes.
A significant difference was observed between the vegetated and non-vegetated slopes in terms of the Fr. As shown in Figure 7b, the Fr of the bare slope ranged from 0.98 to 1.35, while the Fr was less than 1 before S27 for the vegetated slope, suggesting that the vegetated slope under all experimental conditions showed subcritical flow. Most studies have demonstrated that the flow in a vegetated channel was subcritical, while supercritical flow along a vegetated surface was rare [49]. In our study, the Fr increased rapidly after S27, and the subcritical flow became supercritical. In this manner, it could be implied that the arrangement of vegetation density would affect the formation and the development of soil erosion processes along the slope, and the footslope would be more easily eroded due to the complexity of flow patterns. Therefore, the location of the outflow (S27) where the flow state rapidly changed should strengthen the protection.

Reynolds Number and Froude Number
The Re values along the flow direction ranged from 4400 to 11,200, which corresponded to transitional and turbulent flow regimes (Figure 7a). Wang et al. [6] also found that overland flow began with transitional flow at the top of a given slope, and finished with turbulent flow on the bottom. The comparably smaller Re values on vegetated slopes than that of the bare slope indicated less intense turbulent characteristics. In addition, on vegetated slopes, the Re values at vegetated sections (4000-6000) were much smaller than those of nonvegetated sections (8000-10,000). Previous studies also found that the turbulent intensity would decrease further with the increase in vegetation coverage [18,48]. Moreover, Zhao et al. [23] found that increasing vegetation cover was crucial to reducing soil loss. A decrease in Re meant a decrease in the flow turbulence and erosion force, and it resulted in a further reduction of soil loss. Moreover, the Re increased sharply directly after the flow exited the vegetated sections, which was mainly because vegetation not only reduced the energy and dispersed runoff, but also increased the surface roughness. Thus, vegetation played an important role in delaying the flow velocity over slopes.
A significant difference was observed between the vegetated and non-vegetated slopes in terms of the Fr. As shown in Figure 7b, the Fr of the bare slope ranged from 0.98 to 1.35, while the Fr was less than 1 before S27 for the vegetated slope, suggesting that the vegetated slope under all experimental conditions showed subcritical flow. Most studies have demonstrated that the flow in a vegetated channel was subcritical, while supercritical flow along a vegetated surface was rare [49]. In our study, the Fr increased rapidly after S27, and the subcritical flow became supercritical. In this manner, it could be implied that the arrangement of vegetation density would affect the formation and the development of soil erosion processes along the slope, and the footslope would be more easily eroded due to the complexity of flow patterns. Therefore, the location of the outflow (S27) where the flow state rapidly changed should strengthen the protection.

Darcy-Weisbach Friction Coefficient and Manning Coefficient
The f value exhibited a fluctuating downward trend ranging from 0.09 to 0.02 on vegetated slopes, and showed high values on non-vegetated sections and smaller values on vegetated sections. Meanwhile, f maintained a constant value of 0.0048 on the bare slope (Figure 8), and this value was two to 20 times smaller than that of the vegetated slopes, indicating that the presence of vegetation could significantly increase the resistance, such as the form resistance and wave resistance, which were the dominant elements in the vegetated section [50]. The f value decreased in the vegetation section, and gradually increased in the non-vegetation section. This was because in Equations (2) and (7), f was closely related to the variation of water depth. The presence of plants led to increasing water depth at the forepart and decreasing flow velocity. Specifically, the resistance was affected by the intervals: fDMS was highest at the first section (S1-S5), fMDS was highest at the second section (S9-S13), and fSMD was highest at the third section. These findings demonstrated that the regional resistance coefficient of the forepart of the vegetation was proportional to the density of the rear vegetation. Overall, increases in vegetation coverage were beneficial to the siltation of a large amount of sediment, and achieved the functions of soil and water conservation [51,52].  (Figure 8), and this value was two to 20 times smaller than that of the vegetated slopes, indicating that the presence of vegetation could significantly increase the resistance, such as the form resistance and wave resistance, which were the dominant elements in the vegetated section [50]. The f value decreased in the vegetation section, and gradually increased in the non-vegetation section. This was because in Equations (2) and (7), f was closely related to the variation of water depth. The presence of plants led to increasing water depth at the forepart and decreasing flow velocity. Specifically, the resistance was affected by the intervals: f DMS was highest at the first section (S1-S5), f MDS was highest at the second section (S9-S13), and f SMD was highest at the third section. These findings demonstrated that the regional resistance coefficient of the forepart of the vegetation was proportional to the density of the rear vegetation. Overall, increases in vegetation coverage were beneficial to the siltation of a large amount of sediment, and achieved the functions of soil and water conservation [51,52].

Darcy-Weisbach Friction Coefficient and Manning Coefficient
The f value exhibited a fluctuating downward trend ranging from 0.09 to 0.02 on vegetated slopes, and showed high values on non-vegetated sections and smaller values on vegetated sections. Meanwhile, f maintained a constant value of 0.0048 on the bare slope (Figure 8), and this value was two to 20 times smaller than that of the vegetated slopes, indicating that the presence of vegetation could significantly increase the resistance, such as the form resistance and wave resistance, which were the dominant elements in the vegetated section [50]. The f value decreased in the vegetation section, and gradually increased in the non-vegetation section. This was because in Equations (2) and (7), f was closely related to the variation of water depth. The presence of plants led to increasing water depth at the forepart and decreasing flow velocity. Specifically, the resistance was affected by the intervals: fDMS was highest at the first section (S1-S5), fMDS was highest at the second section (S9-S13), and fSMD was highest at the third section. These findings demonstrated that the regional resistance coefficient of the forepart of the vegetation was proportional to the density of the rear vegetation. Overall, increases in vegetation coverage were beneficial to the siltation of a large amount of sediment, and achieved the functions of soil and water conservation [51,52]. Because the Manning roughness coefficient is advantageous when comparing vegetated and non-vegetated conditions, the n values were derived by Equations (11)- (13) to compare the waterblocking effect of vegetation in different density arrangements (Table 5) Longitudinal Distance (m) S1 S5 S9 S13 S17 S21 S27 Because the Manning roughness coefficient is advantageous when comparing vegetated and non-vegetated conditions, the n values were derived by Equations (11)-(13) to compare the water-blocking effect of vegetation in different density arrangements (Table 5). For the same vegetation densities, the n values varied greatly in the different arrangements, which demonstrated that the location of the vegetation had a considerable impact on the water blocking effect of plants. The sum of the Manning coefficient for each arrangement ranked from the highest to the lowest was as follows: SMD > MSD > SDM > DSM > MDS > DMS. The n values of the footslopes were the largest ones among all arrangements, illustrating that the vegetation density at the footslope plays a key role in water resistance.

Vertical Dynamics at Typical Cross-Sections under the Optimal Configuration
As mentioned in Sections 3.1 and 3.2, the SMD arrangement was much more effective in increasing the flow resistance, storing E, reducing erosion and turbidity, and maintaining a steady flow pattern. Therefore, the SMD pattern was taken as the optimal configuration, and the vertical dynamics and turbulent characteristics of this pattern at typical sections S2, S6, S10, S14, S18, and S22 ( Figure 3a) were detected. Due to the limitations of ADV measurements, measurements could not be performed after S27, since the water flow was too shallow. Similar observations were found on bare slopes compared with vegetated slopes.

Velocity Profile
The dimensionless velocity profiles u/u for the six sections were shown in Figure 9; in this term, u represented the mean of stream-wise velocities at a certain point, and u represented the average stream-wise velocity of the whole velocity profile. z/h was relative water depth, h was the water depth of each section, z was the depth of each measuring point. Under the SMD arrangement, we arranged the flow discharge as 3.8 L/s (maximum), the vertical velocity profiles of vegetated sections gradually approached the velocity profile of the bare slope on S6, S14, and S22, whereas the velocity profiles of non-vegetated sections gradually departed from the vertical velocity profile of the bare slope on S2, S10, and S18. Bennett et al. [53] carried out an experimental study on the change of velocity distribution caused by vegetation compression, and their results showed that vegetation can obviously reduce the velocity both inside and around the vegetation section, and the flow was compressed by vegetation but tended to easily cross the non-vegetated section.
All of the velocity profiles followed a power law only for z/h values greater than 0.2. The curve-fitting equations of vertical distribution profiles using data for z/h > 0.2 were shown in Table 6. Along the vertical plane, the velocity profile could be divided into three parts in the last section (S22): the first layer was 0-0.2 h, where the flow velocity increased rapidly. In this part, the low velocity area was near the bottom, and it could be approximately regarded as shear velocity [54]. The second layer was 0.2 h-0.4 h, where the velocity decreased because of disturbances to the vegetation stems, and the resistance and pressure gradient caused the transverse turbulence intensity of the plant to outweigh the vertical stress due to the disturbance of the plant. The third layer was 0.4 h-1 h, where the velocity increased rapidly until the top of the plant stem, which it stabilized. The third area represented the main area of turbulent exchange, where the balance of momentum was maintained, and changes in this section were mainly due to the sudden change of velocity at the top of the plant, which produced shear stress and led to turbulence. Chen et al. [55] also observed three layers based on the velocity distribution profile, which supported the idea that the flows in the region near the bed and at the top of the stems were very unstable, and led to the formation of coherent structures. Previous studies have found that sediment transport occurred in the range of 0-0.2 h [56]. Therefore, the last section, where the vertical velocity increased rapidly and was greater than that of bare flow, had the highest possibility of severe soil erosion. Except for section S22, the velocity profiles in other sections could be divided into two layers: the first layer was 0-0.2 h, which was mainly affected by the bottom layer, velocity gradient was generated by shear stress of the viscous sub-layer, it was equivalent to the first layer of the three layers and presented rapid increases in flow velocity. The second layer was above 0.2 h, and the velocity was almost stable. Thus, vegetation density had an obvious influence on the vertical velocity distribution, and a density threshold may have influenced the turbulence intensity distribution [57].
Water 2018, 10, x FOR PEER REVIEW 15 of 20 second layer was above 0.2 h, and the velocity was almost stable. Thus, vegetation density had an obvious influence on the vertical velocity distribution, and a density threshold may have influenced the turbulence intensity distribution [57].

Reynolds Stress Number
Blockage by aquatic vegetation could affect the turbulence structure in vegetated areas, even in s sparse population of rigid emergent vegetation [58]. The RSN for all three longitudinal sections at S2, S6, S10, S14, S18, and S22 were calculated for the SMD arrangement and bare slope (Figure 10a).
The RSNs on the bare slope were five times as large as those on the vegetated slope, and because they were not affected by any vegetation factors, they appeared to be more stable. By analyzing the significant level of differences between RSNs at different longitudinal sections LS1, LS2 and LS3 ( RSN P = 0.97), it could be deduced that the effect from the wall could be neglected. For the SDM arrangement, the RSN values were always higher near the beginning of the vegetation section. The

Reynolds Stress Number
Blockage by aquatic vegetation could affect the turbulence structure in vegetated areas, even in s sparse population of rigid emergent vegetation [58]. The RSN for all three longitudinal sections at S2, S6, S10, S14, S18, and S22 were calculated for the SMD arrangement and bare slope (Figure 10a).
The RSNs on the bare slope were five times as large as those on the vegetated slope, and because they were not affected by any vegetation factors, they appeared to be more stable. By analyzing the significant level of differences between RSNs at different longitudinal sections LS1, LS2 and LS3 (P RSN = 0.97), it could be deduced that the effect from the wall could be neglected. For the SDM arrangement, the RSN values were always higher near the beginning of the vegetation section. The RSNs of LS1, LS2, and LS3 decreased in the non-vegetation section, and increased in the vegetation section. The flow was less disturbed by vegetation before it entered the vegetation section, and the RSN presented obvious increases after entering the vegetation section; thus, the RSNs in the vegetation section increased as the vegetation density increased. Particularly, the RSNs in the last vegetation section were 2.5 times larger than that of the non-vegetation section, which may be caused by the horseshoe vortex [59] and the karman vortex [60] generated by the impediment of the vegetation stem. The presence of these vortices would successively cause the rise of turbulent kinetic energy [61]. Figure 10b exhibited the vertical depth distribution of RSN in different directions of LS1 at the last cross section of SMD arrangement, which basically changed in a consistent manner: as the water depth increased, the RSN initially increased and then decreased. The sequence of the three directions was longitudinal (u) > transverse (v) > vertical (w).
These results suggested that the presence of vegetation could effectively decrease the turbulent energy and RSNs than bare slope [55], which would efficiently decrease soil erosion by modifying the whole velocity profile and momentum distribution. Nevertheless, certain local locations, e.g., the footslope, were prone to be featured with more intensive turbulent intensities, and thus they accelerated the staring of the sediment load. Therefore, more measures should be taken into account for the protection of soil and water loss. RSNs of LS1, LS2, and LS3 decreased in the non-vegetation section, and increased in the vegetation section. The flow was less disturbed by vegetation before it entered the vegetation section, and the RSN presented obvious increases after entering the vegetation section; thus, the RSNs in the vegetation section increased as the vegetation density increased. Particularly, the RSNs in the last vegetation section were 2.5 times larger than that of the non-vegetation section, which may be caused by the horseshoe vortex [59] and the karman vortex [60] generated by the impediment of the vegetation stem. The presence of these vortices would successively cause the rise of turbulent kinetic energy [61]. Figure 10b exhibited the vertical depth distribution of RSN in different directions of LS1 at the last cross section of SMD arrangement, which basically changed in a consistent manner: as the water depth increased, the RSN initially increased and then decreased. The sequence of the three directions was longitudinal (u) > transverse (v) > vertical (w). These results suggested that the presence of vegetation could effectively decrease the turbulent energy and RSNs than bare slope [55], which would efficiently decrease soil erosion by modifying the whole velocity profile and momentum distribution. Nevertheless, certain local locations, e.g., the footslope, were prone to be featured with more intensive turbulent intensities, and thus they accelerated the staring of the sediment load. Therefore, more measures should be taken into account for the protection of soil and water loss.

Conclusions
The hydrodynamics features of overland flow affected by emergent rigid vegetation with different density and location arrangements, i.e., SMD, SDM, DSM, DMS, MSD and MSD, were investigated in this study. A fixed flume experiment was conducted under seven different flow rates, and the hydrodynamic characteristics in multiple directions (traverse, longitudinal, and vertical) were highlighted based on the hydrodynamic parameters (v, h, Re, Fr, f, n, and E), turbulent intensity, and RSN. The main findings were as follows.
(1) The variation laws of the total hydrodynamic parameters versus discharge on the vegetated slopes were quite similar to that of the bare slopes, although significant differences were observed in the v, Re, and Fr values, which were approximately two or three times larger than that of the bare slope, and the f value, which was approximately eight times as large as that of the bare slope. The relationship between the f and Re became much less pronounced on vegetated slopes, suggesting that the Re was not a unique predictor of hydraulic roughness on vegetated slopes. Among all the slope arrangements, the SMD presented the lowest velocity, RSN, and Fr, and the largest resistance and Manning coefficient values.

Conclusions
The hydrodynamics features of overland flow affected by emergent rigid vegetation with different density and location arrangements, i.e., SMD, SDM, DSM, DMS, MSD and MSD, were investigated in this study. A fixed flume experiment was conducted under seven different flow rates, and the hydrodynamic characteristics in multiple directions (traverse, longitudinal, and vertical) were highlighted based on the hydrodynamic parameters (v, h, Re, Fr, f, n, and E), turbulent intensity, and RSN. The main findings were as follows.
(1) The variation laws of the total hydrodynamic parameters versus discharge on the vegetated slopes were quite similar to that of the bare slopes, although significant differences were observed in the v, Re, and Fr values, which were approximately two or three times larger than that of the bare slope, and the f value, which was approximately eight times as large as that of the bare slope. The relationship between the f and Re became much less pronounced on vegetated slopes, suggesting that the Re was not a unique predictor of hydraulic roughness on vegetated slopes. Among all the slope arrangements, the SMD presented the lowest velocity, RSN, and Fr, and the largest resistance and Manning coefficient values.
(2) Longitudinally, the hydrodynamic parameters maintained constant values on bare slopes, but exhibited spatial variations on the vegetated slopes. The velocity and water depth of different cross sections demonstrated the blocking effect before vegetated areas, and a rapid conveyance effect in vegetation areas. Similarly, E and f exhibited fluctuating downward trends, with the potential energy accounting for the greatest impact. For all vegetated arrangements, the Re values of the vegetated sections were half the value of the non-vegetated sections, whereas the F r number showed a sharp growth after the water flowed out of the tested section. Analyses of the Manning coefficient demonstrated that vegetation density at the footslope played a key role in water resistance. Among the different vegetation arrangements, the h, Re, E, and f values suggested that the dense rearward arrangement (SMD) was the optimal vegetation pattern for regulating flow conditions and reducing water and soil loss. (3) Vertically, the velocity distribution was affected by the presence of vegetation. The dimensionless velocity profile generally followed the power law only for z/h values greater than 0.2. Specifically, three layers were recognized in the velocity profiles at the outlet section, whereas two layers were observed for the other sections, indicating a threshold of density coverage that influenced the turbulence intensity. The comparably smaller RSNs on vegetated slopes compared with bare slopes further illustrated the positive effect of vegetation on reducing flow dynamics. Nevertheless, the higher velocity at the bottom layer and the larger RSN value at section S22, which featured dense vegetation, indicated that local scour was most likely to occur at the end of the outflow section. This finding could help identify the mechanisms underlying local soil erosion, and provide guidance for forest management and environmental protection.