Study on Volatile Organic Compound (VOC) Emission Control and Reduction Potential in the Pesticide Industry in China

: The pesticide industry is one of the primary industries with large and complex VOC emissions. The present study examined the emission characteristics and whole-process control of VOCs in the pesticide industry in China by reviewing pollutant discharge permits, questionnaires, and site investigations. After evaluating the effectiveness of current treatment technologies, the potential of VOC emission reduction in China was analyzed. The results indicate that there are 41 key VOC substances in the pesticide industry that should be given considerable attention. Among treatment facilities, incineration was found to be the most efﬁcient technology, with a removal rate of 53–98% and coverage rate of 23.3%. Multistage absorption–adsorption is a universal technology that had a removal rate of 35–95% and coverage rate of 64.14%. Multistage absorption was used most frequently, with a coverage rate of 71.99%, but its removal rate was between 16 and 85%. Pesticide factories were divided into three levels according to their pollution control capability; the comprehensive removal rates of benchmark, moderate, and poor factories were 81%, 46%, and 8%, respectively, and the emission reduction ratios for high, moderate, and low targets were 41.55%, 32.12%, and 24.32% with corresponding emission reduction costs of $0.653, $0.505, and $0.038 billion/year. The results and prospects from this study will provide support for policy development in industrial VOC emission control in China during the “14th Five-Year Plan” period.


Introduction
The efforts to mitigate and control air pollution during the 13th Five-Year Plan period in China have achieved remarkable results, as air quality has significantly improved [1].In 2020, the proportion of days with good air quality nationwide was 87%, which is an increase of 5.8% from 2015 [2].However, the concentration of fine particles (PM 2.5 ) remains high and the concentration of ozone (O 3 ) is slowly increasing, which are the most important factors affecting air quality [3][4][5].Volatile organic compounds (VOCs) are the key precursors for the formation of ground-level O 3 and atmospheric PM 2.5 [6,7].This implies that the abatement of VOC emissions should be one of the priorities in improving China's air quality.
A global VOC emission inventory concluded that the organic chemical industry was one of the main sources of emissions [8].Moreover, industrial emissions are the main source of anthropogenic VOCs in the atmosphere in China [9][10][11].Many studies have confirmed that solvents dominate among industrial VOCs [12,13], and a large number of solvents are applied during the production of pesticides [14,15].The pesticide production industry contributes significantly to VOC emissions through the organic chemical industry in China, which is due to to the fact that China is both the largest producer and largest consumer of pesticides worldwide [16].The chemical synthesis process within the pesticide industry is extremely complex, as large quantities of many organic and inorganic raw materials, organic solvents, and catalysts are used to produce organic products, intermediates, and other substances.There are various volatile and highly toxic substances involved in pesticide manufacturing, including aromatic hydrocarbons, esters, ethers, ketones, and aldehydes, which can cause a plethora of health problems [17][18][19][20].
Recently, a number of studies have focused on establishing VOC emission inventories to quantify and characterize pollutant emissions at national, regional, and city scales [21][22][23][24][25].In 2021, China issued a notice of accelerating the resolution of the current prominent problems regarding the treatment of VOCs, which regulated that all regions should focus on key VOC emission industries.The emissions of the pesticide factories in China need to comply with the "Emission standard of air pollutants for pesticide industry" (GB 39727-2020) [26].However, there is still a lack of analysis on the emission characteristics and whole-process control of the key industries in China, such as the pesticide industry.No reports have studied the reduction potential of the pesticide industry in China during the 14th Five-Year period.
The main objectives of this study were (1) to identify the characteristics of VOC emissions and the status of management and control in the pesticide industry in China, (2) to evaluate the effectiveness of current treatment technologies, and (3) to analyze the potential of VOC emission reduction in China.The results and implications from this study will provide support for VOC management for the prevention and control of ozone pollution in China during the "14th Five-Year Plan" period, which demands that new progress in ecological civilization construction be achieved.

Study Objects
The number of pesticide manufacturing factories in China is approximately 1500~1700, of which approximately 400~500 are original pesticide manufacturers.At present, pesticide factories are mainly distributed among the four provinces of Jiangsu, Shandong, Henan, and Hebei in the central and eastern regions of China, shown in Figure S1.To ensure the representativeness of the study objects, the selected pesticide production factories covered different production types (chemical original pesticides, biological original pesticides, and pesticide formulations) and regions.

Data Collection
The data on VOC treatment facilities in pesticide production factories were obtained from pollutant discharge permits for 385 factories, questionnaires and information lists for 48 factories, and site investigations of 16 factories.The basic factory information collected included engineering and construction technical data, daily operation technical data, investment costs, operation costs, and self-monitoring VOC emission data.
When entering a factory, a VOC portable detector, anemometer, and other equipment were used to determine the VOC concentration and wind speed at production units, storage tanks, confined spaces, wastewater treatment plants, and other locations to find weak points in the control of VOCs in pesticide production factories.If a factory lacked environmental monitoring data, a supplementary monitoring plan was developed to obtain the import and export concentrations of the VOC treatment facilities, employing the determination method in the standard entitled "Stationary source emission-Determination of total hydrocarbons, methane and nonmethane hydrocarbons-Gas chromatography" (HJ 38-2017) [27].

Collection Rate of Exhaust Gas
The key steps associated with fugitive emissions were solid-liquid separation and feeding/discharging.Due to the suction effect of the collection system, the air enters from the tuyere from all directions and converges to the external receiving hood.The external receiving hood sucks in the airflow and the harmful gas at the same time.The collection rate of the exhaust-gas collection system is calculated by the formula as follows [28]: where α represents the collection rate of exhaust gas, Q represents the volume of the air collecting hood (m 3 /s), C represents the average concentration of VOCs at the mouth of the hood (kg/m 3 ), and q m .represents surface volatilization rate of VOCs (kg/s).

Facility Removal Rate
There are many types of terminal VOC treatment technologies with different scopes of application and treatment efficiencies.For factories that had a sampling port for exhaust gas before treatment, samples before and after treatment were collected at the same time, and the facility removal rate was calculated according to the quantitative total nonmethane hydrocarbon concentration.The calculation formula is as follows [29]: where β represents the facility removal rate, Q 1 .represents the volume of the inlet exhaust gas (m 3 /h), C 1 represents the concentration of the inlet exhaust gas (kg/m 3 ), Q 2 represents the volume of the outlet exhaust gas (m 3 /h), and C 2 .represents the concentration of the outlet exhaust gas (kg/m 3 ).

Facility Commissioning Rate
For factories with online monitoring or central control system facilities, the commissioning rate of the pollution control facilities were verified through online monitoring and central control system data if possible.For treatment facilities equipped with independent electricity meters, the commissioning rate was calculated by the following formula: where γ represents the facility commissioning rate, which is the ratio of the actual value to the design reference value under the same reference (power or dosage of agent); P represents the power consumption of the management facilities (MKW/a); T represents the facility operation time (h/a); and W represents the device rated power (KW).

Comprehensive Facility Removal Rate
The comprehensive facility removal rate was calculated by the following formula: where η represents the comprehensive facility removal rate, α represents the collection rate of exhaust gas, β represents the facility removal rate, and γ represents the facility commissioning rate.

Design Scenario
According to the different pollution-control capabilities of pesticide manufacturing factories, the grading standards are determined by the aspects of equipment level, collection method of exhaust gas, treatment facilities, and daily management.Factories were divided into three levels, including benchmark factories (referred to as "benchmark"), medium governance level factories (referred to as "moderate"), and factories with poor governance (referred to as "poor"), which are used to reasonably estimate the exhaust-gas collection rate, facility removal rate, and facility commissioning rate of factories in different categories.
Based on the differences in the overall equipment levels of regional pesticide factories, the proportions of benchmark, moderate, and poor factories were 15%, 50%, and 35%, respectively, in the provinces of Jiangsu and Zhejiang.The proportions of benchmark, moderate, and poor factories were 10%, 40%, and 50%, respectively, in the Shandong province.In other provinces that were hypothesid to be similar to one another, benchmark factories were not identified, and the proportions of moderate and poor factories were 30% and 70%, respectively.Therefore, the overall proportions of benchmark, moderate, and poor factories at the national level were 9.2%, 41.3%, and 49.5%, respectively.According to the "14th Five-Year Plan" VOC emission reduction requirements and the actual situation of the pesticide industry, the number and scale of pesticide factories in China will remain unchanged, and the emission reduction of VOCs will be achieved through self-improvement.Three different target levels were set as shown in Table 1.The exhaust gas collection rate α, facility commissioning rate β, and facility removal rate γ of benchmark, moderate, and poor factories were calculated to obtain the corresponding comprehensive removal rate η.Based on the proportion of benchmark, moderate, and poor factories under different targets, the VOC emissions under each target were calculated, and the difference between the current VOC emissions and the VOC emissions under each target was considered the emission reduction.
where E current represents the current VOC emissions, E produce represents the VOC production, η benchmark , η moderate , and η poor represent the comprehensive removal rates of benchmark, moderate, and poor factories, and a benchmark , a moderate , a poor represent the proportions of benchmark, moderate, and poor factories under different targets.

Characteristics of VOC Pollution in the Pesticide Manufacturing Industry
Due to the use of inorganic substances, the transformation of solid products, and the use of combustion treatment facilities, pesticide waste gas is generally a mixture of inorganic and organic pollutants.Therefore, a combined process is generally used for the actual treatment of organic waste gas, and inorganic pollutants are firstly treated to reduce the impact of organic waste gas treatment facilities.
Due to the characteristics of pesticide industry processes, the reuse value of VOC organic waste gas is high.First, waste gas is condensed and recovered in the production workshop, and then it enters the terminal treatment facilities in the factory, clearly demonstrating a two-stage characteristic.Additionally, exhaust gas emissions in the pesticide industry are synchronized with production, which has intermittent characteristics, so there are occasional cases where high-concentration exhaust gas exceeds the standard during the VOC treatment process.The process flow diagram of the pesticide factory is shown in Figure 1.The characteristics of VOC emissions in the pesticide industry are summarized in Table 2. Note: The discharge concentration of VOC in terms of the nonmethane hydrocarbons (NMHC) is 100 mg/m 3 in "Emission standard of air pollutants for pesticide industry" (GB 39727-2020) [26].
The summarized discharge concentrations in Table 2 represent the values after collection and treatment.The general collection methods in the pesticide industry are relatively extensive at present, with an average collection rate of 50-60%.However, discharges at many link points cannot be effectively collected, as more than 90% use cold upper and side suction hoods, approximately 80% use direct connections between the equipment and outlet, approximately 40% use airtight collection in workshops or closed rooms, approximately 60% are collected in semi-airtight hoods or fume hoods, and approximately 30% are collected in hot upper suction hoods, leading to the characteristics of large air volume and low concentration of organic waste gas.pesticide industry are synchronized with production, which has intermittent characteristics, so there are occasional cases where high-concentration exhaust gas exceeds the standard during the VOC treatment process.The process flow diagram of the pesticide factory is shown in Figure 1.The characteristics of VOC emissions in the pesticide industry are summarized in Table 2.

List of Key VOC Substances in Pesticide Manufacturing Industry
The list of key VOC substances in the pesticide manufacturing industry was based mainly on the characteristics of industrial production and discharge, solvent use, current control standards [26], maximum incremental reactivity (MIR) value of substances, health risk, and so on [30][31][32][33].
Organic solvents used in pesticide manufacturing are one of the main VOC substances emitted.The characteristic pollutants that are routinely monitored by factories are benzene, toluene, xylene, methanol, formaldehyde, chlorobenzene, phenols, acetone, acetonitrile, ethyl acrylate, etc.According to the use frequency of more than 40 kinds of pesticides, the top seven organic solvents are toluene, methanol, xylene, ethanol, dichloroethane, benzene, and acetonitrile.The VOCs regulated by current standards mainly include phosgene, acrylonitrile, benzene, benzene series compounds, formaldehyde, phenols, chlorobenzenes, and methanol.The key VOC substances selected after careful screening are shown in Table 3.The usage of VOC treatment facilities was summarized according to the pollutant discharge permits of 385 pesticide manufacturing factories, as shown in Figure 2. Organic waste gas treatment in the pesticide manufacturing industry mostly adopts combined processes, among which absorption and adsorption processes are used most often, with frequencies of 71.99% and 64.14%, respectively; incineration follows with a frequency of 23.30%; photocatalytic oxidation, plasma, ultraviolet photolysis, and other inefficient technologies are used less, with frequencies of 6.28%, 2.88%, and 2.36%, respectively.From the statistics above, it can be seen that most of the VOC treatment methods in the pesticide industry adopt a combined absorption-adsorption technique.

Facility Removal Rates of VOCs
The VOC removal rates of the common and combined processes were assessed in terms of historical facility removal rates, VOC treatment facility removal rates in the pesticide industry from the second pollution-source census of China, and our supplementary monitoring data, all of which are shown in Table 4.According to the "Emission Standard of Air Pollutants for Pesticide Manufacturing Industry" (GB39727-2020) [26], the removal rate of VOC treatment facilities in the pesticide industry should not be less than 80%.The recommended combined processes and removal rates of specific pollutants are shown in Table 5.
According to Tables 4 and 5, the efficiency of treatment facilities decreases significantly with reduction in organic waste gas concentration, so the large volume and low concentration of pesticide organic waste gas make it difficult for treatment facilities to achieve the intended removal effect.Furthermore, the detected concentrations of

Facility Removal Rates of VOCs
The VOC removal rates of the common and combined processes were assessed in terms of historical facility removal rates, VOC treatment facility removal rates in the pesticide industry from the second pollution-source census of China, and our supplementary monitoring data, all of which are shown in Table 4.According to the "Emission Standard of Air Pollutants for Pesticide Manufacturing Industry" (GB39727-2020) [26], the removal rate of VOC treatment facilities in the pesticide industry should not be less than 80%.The recommended combined processes and removal rates of specific pollutants are shown in Table 5.According to Tables 4 and 5, the efficiency of treatment facilities decreases significantly with reduction in organic waste gas concentration, so the large volume and low concentration of pesticide organic waste gas make it difficult for treatment facilities to achieve the intended removal effect.Furthermore, the detected concentrations of pesticide organic waste gas are still extremely low, partly because the responsiveness of some specific VOCs is low when employing a hydrogen-flame ionization detector (FID) to determine the nonmethane total hydrocarbon, meaning that the results are generally low when analyzing oxygenated volatile organic compounds [36].In addition, the removal effect of treatment facilities is inevitably related to the quality and brand of the equipment used.
It should be emphasized that some raw and auxiliary materials in the pesticide industry have a relatively low odor threshold and a large amount of unorganized emissions, which can easily lead to complaints and discomfort.Inefficient VOC treatment systems, such as photocatalytic oxidation and low-temperature plasma, are more effective than other systems in the removal of odorous substances.Therefore, the use of such VOC treatment facilities can be encouraged under certain conditions.

Collection Rate of Exhaust Gas
The collection rate of exhaust gas in the pesticide industry was derived from the collection rate reported in the second pollution-source census, along with the published standards and industry manuals, and the results are shown in Table 6.The equipment has a fixed discharge pipe (or port) directly connected to the air duct.The equipment is completely sealed, leaving only the product inlet and outlet open, and there are exhaust gas collection measures at the inlet and outlet.When the collection system is running, hardly any VOCs are emitted around it.

Confined collection in workshop or closed room
Approximately 40% 80~95 The roof is cast in place, and the surrounding walls, doors, and windows have good airtightness.The total air volume collected ensures a slight negative pressure at the opening (the suction wind speed at the open section is not less than 0.5 m/s), and exhaust gas is not leaked.

Semi-closed hood or fume hood Approximately 60% 65~85
At the point (surface) of pollutant generation, the controlled wind speed towards the suction port shall not be less than 0.5 m/s.

Hot upper suction hoods Approximately 30% 30~60
At the point (surface) of pollutant generation, the controlled wind speed towards the suction port shall not be less than 0.5 m/s."Hot" refers to the temperature of the gas emitted by the pollution source, which must be ≥60 • C.

Cold upper suction hoods >90% 20~50
At the point (surface) of pollutant generation, the controlled wind speed towards the suction port shall not be less than 0.5 m/s."Cold" refers to the temperature of the gas emitted by the pollution source, which must be <60 • C.

Side suction hoods >90% 20~40
At the point (surface) of pollutant generation, the controlled wind speed towards the suction port shall not be less than 0.5 m/s, and the distance between the suction hood and the far end of the pollution source shall not be greater than 0.6 m.

Emission Reduction Benefit and Economic Evaluation
The investment cost, operating cost, emission concentration, design air volume, design removal rate, and other information related to VOC treatment facilities at eight pesticidemanufacturing factories were investigated.
The investment cost of regenerative thermal oxidation (RTO) in the pesticide industry was high; the main equipment cost was approximately $0.51 million to $2.66 million according to the air inlet volume, excluding pipelines and other renovation costs, so the equipment cost per 10,000 cubic meter of air volume was approximately $0.36 million.In addition to technical integration and operational stability, the cost of RTO is determined by the materials of the RTO frame (such as corrosion-resistant materials), the materials in the heat storage components (such as cordierite, mullite, and alumina), and the preheating device.According to the statistics, the annual operating cost of RTO accounts for approximately 25~30% of the one-time investment.It is estimated that the annual VOC emission reduction of RTO with 40,000 cubic meters of air volume is 187.51 tons.Furthermore, the investment cost of other combustion treatment facilities, such as catalytic combustion with 20,000 cubic meters of air volume, was $0.40 million, and the operating cost accounted for approximately 27% of the one-time investment.
Regarding unorganized source collection, the investment cost of capping the wastewater treatment facility was approximately $0.088 to $0.89 million, including the cost of the pipeline or treatment facilities.The cost associated with gas-phase balance in the volatile organic liquid storage tank was approximately $0.028 million, and that of the gas-phase equilibrium device, including adsorption, was approximately $0.41 million.Different facilities in a plant have different costs for airtight transformation, the investment costs of which are $0.12 to $0.55 million.The cost of pipelines is related to the length, diameter, and material of the pipe itself, and the installation cost is approximately 80% of the material cost.
In summary, the emission reduction benefits and economic evaluations of different treatment facilities in the pesticide industry based on the characteristics of the surveyed factories are shown in Table 7.

VOC Emission Reduction Potential of the Pesticide Manufacturing Industry
According to the investigation of the actual production status of typical pesticide factories, different production processes and equipment levels will lead to different VOC proportions in each pollution-producing node.After comprehensive analysis, the VOC emission proportion of each node was determined and results are shown in Figure 3.The reaction waste gas includes two parts, equipment-venting waste gas and vacuuming waste gas, the latter of which is included in the vacuum system.Benchmark factories have relatively high degrees of airtightness, pipeline quality, and process automation, and the collection rate should meet or exceed the requirements.The values for moderate and poor factories were appropriately decreased.The adjusted collection rates of VOCs in the pesticide industry, shown in Figure 4 and Table S1, were calculated by reviewing and revising the data based on the actual use of collection and processing facilities.Benchmark factories have relatively high degrees of airtightness, pipeline quality, and process automation, and the collection rate should meet or exceed the requirements.The values for moderate and poor factories were appropriately decreased.The adjusted collection rates of VOCs in the pesticide industry, shown in Figure 4 and Table S1, were calculated by reviewing and revising the data based on the actual use of collection and processing facilities.
Benchmark factories have relatively high degrees of airtightness, pipeline quality, and process automation, and the collection rate should meet or exceed the requirements.The values for moderate and poor factories were appropriately decreased.The adjusted collection rates of VOCs in the pesticide industry, shown in Figure 4 and Table S1, were calculated by reviewing and revising the data based on the actual use of collection and processing facilities.The measures taken by benchmark factories generally include a variety of combined processes, and the overall efficiency should be higher than the required treatment rate.The adjusted facility removal rates of VOCs in the pesticide industry are shown in Figure 5 and Table S2.
Atmosphere 2022, 13, x FOR PEER REVIEW 13 of 17 The measures taken by benchmark factories generally include a variety of combined processes, and the overall efficiency should be higher than the required treatment rate.The adjusted facility removal rates of VOCs in the pesticide industry are shown in Figure 5 and Table S2.In principle, facilities should meet the requirements of 100% use, but the effective utilization rate of facilities decreases due to factors such as untimely addition of chemicals, untimely replacement or regeneration of adsorbents, and untimely maintenance of combustion facilities.The facility commissioning rates are 95%, 80%, and 50% for In principle, facilities should meet the requirements of 100% use, but the effective utilization rate of facilities decreases due to factors such as untimely addition of chemicals, untimely replacement or regeneration of adsorbents, and untimely maintenance of combustion facilities.The facility commissioning rates are 95%, 80%, and 50% for benchmark, moderate, and poor levels in the entire evaluation node, which are presented in Table S3.
Based on the values of α, β, and γ in Tables S1 and S2, the comprehensive removal rates of benchmark, moderate, and poor factories in the pesticide industry were calculated as 86%, 51%, and 10%, respectively, as shown in Table 8.Considering that some factories are not fully covered by collection and treatment facilities, the comprehensive removal rates of factories calculated based on individual processes were too high and required adjustment.The adjustment coefficients of benchmark, moderate, and poor factories were 0.94, 0.9, and 0.8, respectively.After adjustment, the comprehensive removal rates of benchmark, medium, and poor factories were 81%, 46%, and 8%, respectively.According to different emission reduction target stages, the emission reduction ratios of the high, moderate, and low targets were 41.55%, 32.12%, and 24.32%, respectively, and the corresponding emission reduction costs were $0.653, $0.505, and $0.038 billion/year, respectively.
Factories in the pesticide industry can be divided into three categories, corresponding to benchmark, moderate, and poor governance levels, which account for 9.2%, 41.3%, and 49.5% of the national total, respectively, and have comprehensive removal rates of 81%, 46%, and 8%.According to the estimated emission reduction potential, under the high, medium, and low emission reduction targets during the "14th Five-Year Plan" period, the emission reduction rates of VOCs in the pesticide industry are 41.55%, 32.12%, and 24.32%, respectively, and the corresponding emission reduction costs are $0.653,$0.505, and $0.038 billion/year.
As mentioned previously, there are more benchmark factories in the Jiangsu and Zhejiang provinces, followed by Shandong, and the proportion of poor factories is higher in other provinces, especially in the western provinces.Therefore, in order to achieve the target, the improvement of pollution prevention level of the pesticide industry is urgent in provinces, except for those in the southeast.From the perspective of the treatment effect, the efficiency of incineration is the best, generally above 99%, but the input and operating costs of this method are the highest.For the factories that use multistage absorption and activated-carbon adsorption, which accounts for the highest proportion, attention should be paid to the activated carbons with different specifications or different iodine values, which can have a significant impact on the adsorption effect.Furthermore, the replacement frequency of activated carbons is closely related to processing efficiency.
According to the overall process supervision approach of "source reduction-process control-endpoint treatment-daily management", there are several effective methods for lowering pollution levels in the pesticide industry.(1) Source reduction: encourage enterprises to use nonhalogenated hydrocarbons, nonaromatic hydrocarbons, high-solids, and high-boiling point solvents; promote green production processes such as the water-phase method and biological enzymatic synthesis, especially for preparation factories; promote solvents with a high boiling point and low photochemical potential to reduce the environmental impact in the life cycle.(2) Process control: combined with equipment upgrades, improve the airtightness of equipment in storage, transportation, feeding, solid-liquid separation, drying, vacuum system, packaging, solvent storage and transportation, etc. and reasonably design air collection devices for a rational air volume; in principle, avoid overall ventilation air collection in the workshop and avoid situations where an excessive air volume cannot be controlled.(3) Endpoint treatment: accelerate the elimination of inefficient single treatment methods and adopt reasonable treatment technology.Adopt adsorption regeneration as a recommended pretreatment for halogenated hydrocarbon and aromatic hydrocarbon waste gas in principle.Eliminate the use of photo-oxidation and activated carbon adsorption, water spray and activated carbon adsorption, disposable activated carbon adsorption and other processes as end-of-line treatment measures in the treatment of VOC waste gas generated from the production of technical materials and intermediates.Encourage the use of RTO or integrated incineration of waste gas and waste liquid for efficient treatment.(4) Daily management: in view of the intermittent production schedule of pesticide factories and the poor results of conventional leak detection and repair (LDAR) testing, an unannounced inspection system should be established.Sampling inspections will be carried out at selected points; if the number of points exceeds the standard, corresponding punitive measures can be taken to improve the effectiveness of LDAR detection.
Due to the refined pesticide industry emission standards of China, the advanced issuance of pollutant discharge permits, and the tightened requirements for VOCs emission reduction of the factory, the pollution prevention and control level of most pesticide factories is difficult to adapt to the needs of the environmental situation.This paper estimated the emission reduction ratios and the corresponding emission reduction costs through the statistics of pesticide industry in China, but has not formed a technical system that can be seen, learned, and promoted.Therefore, we should establish the best available technical specifications based on integration of industry practices, and compile a recommended catalogue for the production equipment of pesticide industry to standardize the upgrading and transformation of enterprise equipment in future, supporting the development of pollution reduction work in the pesticide industry.

Supplementary Materials:
The following supporting information can be downloaded at https: //www.mdpi.com/article/10.3390/atmos13081241/s1, Figure S1.The regional distribution of the pesticide factories in China.Table S1.Evaluation for collection rate of VOCs in pesticide industry.Table S2.Evaluation of the facility removal rate of VOCs in the pesticide industry.Table S3.Evaluation of the facility commissioning rate of VOCs in the pesticide industry.

Figure 1 .
Figure 1.The process flow diagram of the pesticide factory.

Figure 1 .
Figure 1.The process flow diagram of the pesticide factory.

Figure 2 .
Figure 2. Proportion of VOC treatment usage in pesticide manufacturing industry facilities.

Figure 2 .
Figure 2. Proportion of VOC treatment usage in pesticide manufacturing industry facilities.

Figure 3 .
Figure 3. Nodes and proportions of VOC pollution in the pesticide industry.(Others: hazardous waste temporary storage, dynamic and static equipment sealing, process sampling, circulating water system).

Figure 3 .
Figure 3. Nodes and proportions of VOC pollution in the pesticide industry.(Others: hazardous waste temporary storage, dynamic and static equipment sealing, process sampling, circulating water system).

Figure 4 .
Figure 4. Evaluation for collection rate of VOCs in pesticide industry.(A: preparation, feeding, and reaction process; B: solid-liquid separation; C: drying; D: solvent recovery, vacuum system; E: packaging; F: solvent storage and transportation; G: others, including hazardous waste temporary storage, dynamic and static equipment sealing, process sampling, circulating water system).

Figure 4 .
Figure 4. Evaluation for collection rate of VOCs in pesticide industry.(A: preparation, feeding, and reaction process; B: solid-liquid separation; C: drying; D: solvent recovery, vacuum system; E: packaging; F: solvent storage and transportation; G: others, including hazardous waste temporary storage, dynamic and static equipment sealing, process sampling, circulating water system).

Figure 5 .
Figure 5. Evaluation of the facility removal rate of VOCs in pesticide industry.(A: production process; B: solvent storage and transportation; C: sewage station; D: hazardous waste temporary storage).

Figure 5 .
Figure 5. Evaluation of the facility removal rate of VOCs in pesticide industry.(A: production process; B: solvent storage and transportation; C: sewage station; D: hazardous waste temporary storage).

Table 1 .
Three different levels of VOC emission reduction targets in pesticide factories in China.

Table 2 .
Characteristics of VOC emissions in the pesticide industry.

Table 2 .
Characteristics of VOC emissions in the pesticide industry.

Table 3 .
List of key VOC substances in the pesticide manufacturing industry.

Table 4 .
VOC removal rates by common compliant and combined processes in the pesticide manufacturing industry.

Table 5 .
Recommended combined processes and removal rates of specific pollutants.

Table 6 .
Collection rate of VOCs in the pesticide industry.

Table 7 .
Emission reduction benefits and economic evaluation of different treatment facilities in the pesticide industry.

Table 8 .
Classification of comprehensive removal rates in the pesticide industry (B represents benchmark, M represents moderate, and P represents poor).