Biogeneration of Valuable Nanomaterials from Agro-Wastes: A Comprehensive Review

: The exponential growth of agricultural output is a result of the increasing world population. Agro-wastes are now acknowledged as an alternative material for the manufacture of renewable, inexpensive, and sustainable bio-composite-based products. Huge amounts of agricultural produce are often lost owing to a lack of processing facilities or storage space. Agriculture wastes contain a signiﬁcant concentration of carbohydrates as well as various multifunctional groups and organic substances, such as polymeric proteins. Interestingly, nanotechnology provides better potential to transform agricultural wastes easily into valuable and cost-effective products, removing the need to utilize noxious chemicals, which can create a variety of health and environmental difﬁculties. Recently, there has been an increase in interest in eco-friendly nanomaterial (NM) production techniques that utilize extracts generated from agricultural waste. Such nanoparticles (NPs) have been extensively studied for numerous uses, including antibacterial agents, water puriﬁcation, the breakdown of industrial colours, and many others. Consequently, the purpose of this review is to investigate the different sources, characteristics, and nano-management of agro-waste; valuable NMs derived from agro-waste


Introduction
Agriculture makes the biggest contribution to the economy of a resource sector around the world.It is estimated that Canada makes 36.1 metric tonnes of waste each year, which is 10 metric tonnes more per person than the United States.Every year, Canada makes about 1.33 billion metric tonnes of waste, of which 1.12 billion metric tonnes are industrial waste [1].As of 2020, the United States uses approximately 4532 trillion British thermal units (TBtu), or about 4.9 percent of its total primary energy consumption.Wood and woodderived biomass accounted for about 2101 TBtu, while biofuels (mostly ethanol) provided 2000 TBtu, and municipal garbage generated 430 TBtu [2].The United States produced the most biofuels of any country in the world in 2020, with production estimated to reach 1347 petajoules [3].Agriculture is the primary source of food, trash, greenhouse emissions, and energy in every region of the world.Agriculturally based industries produce a lot of garbage as a result of their operations.Non-consumable plant portions are referred to as agro-waste, while edible parts are the primary source of energy for humans [4].Biological oxygen demand (BOD), chemical oxygen demand (COD), and suspended solids are all significant in this vast volume of agro-waste [5].A lack of effective disposal of these types of waste items can harm the earth's surface and groundwater, which in turn contributes to all forms of pollution.A large portion of garbage is still unutilized and disposed of improperly, which only exacerbates the problem.A variety of agricultural and industrial processes generate low-cost by-products from all over the globe.This aids in the creation of valueadded products from those remnants.There is still a lot of untapped potential in many cases, but nothing practical is being made out of it.Burning, dumping, or uncontrolled land filling are the most common disposal methods for agro-industrial waste that hasn't been processed or repurposed [6].These unprocessed wastes contribute to global warming by emitting a variety of greenhouse gases.As a result, the usage of fossil fuels generates greenhouse gases (GHG) [7].There are numerous possible uses, including the creation of biotechnological products, the synthesis of NPs, and the generation of manure and biofuels, among others (Figure 1).

Nanomaterials and Nano-Management of Agro Wastes
Agro-waste comes in various forms.It can be divided into two primary types, namely agricultural residues and residues from the agricultural industry [22].Further agricultural residues comprise two types, namely process residues (Husk, Bagasse, Molasses, etc.) and field residues (stems, seeds, stalks, etc.).Agricultural industry waste means commerciallevel produce waste such as orange-peel, tea, potato-peel, pineapple-peel, groundnut oil cake, sugarcane, soybean oil cake, cotton, coffee, cereal, chocolate, fruits and vegetables, etc., all contribute significantly to waste.These waste materials can be utilized to make biofuels as well as organic solvents like ethanol, acetone, and butanol.Additionally, pineapple leaf fibre is being researched as a fibre glass replacement [23].Another illustration of lignocellulosic waste that is a sizable representative is waste from the production of wine [24].There are many examples where agro-wastes are used as a replacement for fossil fuel and the manufacturing of NMs.Agro-waste is also environmentally friendly and sustainable.A further method would involve removing these wastes from the environment by utilizing NPs.NPs can be used, for instance, to eliminate airborne pesticides like Malathion and Chlorpyrifos [25].There are several classes of nanofillers available in various nations for spot maintenance, such as removing photocatalytic contaminants from water using titanium oxide nanoparticles as a filter [26].
In current decades, the management of agro-waste has become a major concern, and numerous processes have been developed for dealing with organic wastes, including the Agricultural wastes, which can include horticultural, aquatic, or culinary wastes, contain vital bio-chemicals such aslignin, cellulose, chitin, and polyphenolic compounds [8].By simple pyrolysis, some of the compounds can produce carbon dots, whereas the constituents of other compounds act as reducing, stabilizing, and capping agents during the creation of NPs [9].Because of the economical, environmental, and technological advantages, the fabrication of NMs using agro-waste as substrates is quickly gaining popularity [9].These NPs are prepared using a combination of mechanical and chemical processes, including crushing, grinding, alkali, bleaching, and acid treatments [10].The morphology of nanoscale biopolymers is studied using AFM, SEM, and TEM [11].Researchers are examining the functional group modifications and crystallographic structure of nanoscale biopolymers using FTIR and X-ray diffraction, respectively [12].
In recent years, nanotechnology has reached nearly every zone of technology ranging from clinical, commercial, agricultural, and even residence old utilities, and has hugely facilitated the evolution of current technology.Applications of NPs and nanotechnology have been introduced in recent years in the agricultural and food sectors in order to increase overall sector productivity [13,14].Nanotechnology is a branch of science that deals with materials with sizes between 1 and 100 nm [15].The role of nanotechnology in agriculture and environmental protection is expanding.Agro-waste, which includes weeds such as Gloriosa superba, Medicago sativa, Cyperus rotundus, and Tinospora cordifolia, as well as agricultural residues including ricehusk, soy, and coconut shell, wheat straw, banana peel, orange peel, and pomegranate peel, has been utilized to create nanostructures.Genetically modified organisms (GMPs), atomically modified organisms (AMOs), animal products, insecticides, farming methods, and many other possibilities to study with significant potential to revolutionize the agriculture scenario globally will all benefit from nanotech research in agriculture [16,17].One of the primary goals for potential applications has been to control the particle size, shape, and crystalline nature of the NPs that are produced through the synthesis of NPs [18].NPs serve as a connection between large-scale materials and the atomic or molecular structures that compose them.Because of this, they are excellent candidates for applications in a variety of fields, including medicine, catalysis, electrochemistry, biotechnology, and the detection of trace substances [19].In order to prepare NPs with a variety of morphologies and sizes, various synthetic methods have been utilized [20].Although these methods have produced superior NPs, there is still a need for a fundamental understanding of how to improve the manufacturing process [21].This understanding could be utilized on an industrial and commercial scale to produce products that are better constructed, have a longer lifespan, are cleaner, safer, and more intelligent.Some examples of these types of products include communication technology, medicines, transportation, agriculture, and industrial products.As a result, the primary focus is on the design of NPs using methods that are not harmful to the environment.These provide solutions to the growing problems that are associated with concerns over the environment.This review investigates the characteristics of agro-waste, valuable NMs, and their possible applications.

Nanomaterials and Nano-Management of Agro Wastes
Agro-waste comes in various forms.It can be divided into two primary types, namely agricultural residues and residues from the agricultural industry [22].Further agricultural residues comprise two types, namely process residues (Husk, Bagasse, Molasses, etc.) and field residues (stems, seeds, stalks, etc.).Agricultural industry waste means commerciallevel produce waste such as orange-peel, tea, potato-peel, pineapple-peel, groundnut oil cake, sugarcane, soybean oil cake, cotton, coffee, cereal, chocolate, fruits and vegetables, etc., all contribute significantly to waste.These waste materials can be utilized to make biofuels as well as organic solvents like ethanol, acetone, and butanol.Additionally, pineapple leaf fibre is being researched as a fibre glass replacement [23].Another illustration of lignocellulosic waste that is a sizable representative is waste from the production of wine [24].There are many examples where agro-wastes are used as a replacement for fossil fuel and the manufacturing of NMs.Agro-waste is also environmentally friendly and sustainable.A further method would involve removing these wastes from the environment by utilizing NPs.NPs can be used, for instance, to eliminate airborne pesticides like Malathion and Chlorpyrifos [25].There are several classes of nanofillers available in various nations for spot maintenance, such as removing photocatalytic contaminants from water using titanium oxide nanoparticles as a filter [26].
In current decades, the management of agro-waste has become a major concern, and numerous processes have been developed for dealing with organic wastes, including the use of compost and organic fertilizers, biochar, and the removal of environmental pollutants.Some agro-waste cannot be posted, like oils, due to their low economic value and ability to reduce landfill waste.Consequently, the agro-waste management system has evolved since the last century due to the advancement of our civilization [27].In order to achieve low emissions, low consumption, and high efficiency, agricultural wastes should be managed following the principles of the three Rs (i.e., reduce, reuse, and recycle) [28].Multiple studies evaluated the utilization and management of agro-waste from various perspectives, including: (a) Manufacturing of nano-silica or Si-nanoparticles [29][30][31][32]; (b) Nano-cellulose production as a precious pharmaceutical component [33]; (c) Biochar production [34][35][36][37][38][39]; (d) High-performance super-capacitor manufacturing using porous nano-carbon [40] or graphene oxide [41].

Different Sources of Agro-Waste
Agro-waste is the leftover output of agricultural activities, such as the processing and manufacture of vegetables, fruits, poultry, meat, and dairy products [70].There are four main types of agricultural waste: livestock manure, agricultural sector manure, fruit and vegetable manure, and crop residues and byproducts [71].

Crop Residues
In the field, crop leftovers like stovers, straws, leaves, seed pods, and so on are the primary sources of agro-waste.As the most plentiful and cheap organic waste, these crop wastes can be easily transformed into a wide range of high-value products [72].The three primary crop by-products that are utilized to produce bioethanol globally are wheat straws, corn stovers, and rice straws, which are available all year long.Only a small portion is used to produce biofuels or as animal feed, and the remainder is burned, leading to significant environmental issues [73].Among these three primary agricultural leftovers, rice straw is one of the utmost promising and valuable biomasses globally, with an annual production of approximately 732 million tonnes, and Asia being the leading producer [74].It is estimated that 355.35 million metric tonnes of wheat straws are produced each year in the world, making wheat straw the majority of the waste recovered from wheat [75].Corn stover is one of the most promising crop residues for making lingo-cellulosic ethanol, with an envisioned manufacturing of four tonnes consistent with acre and a global manufacturing of approximately 128 million tonnes per 12 months.Agro-waste is also made up of crop residues from oats, sorghum, and barley [76].

Agricultural Industry Wastes
Waste produced during the preparation of crops for industrial use is the second category of agro-waste.This includes waste products from the extraction of oil or juice, such as sugarcane bagasse, fruit and vegetable peels, and fruit marc/pomace.It also includes products from meat processing facilities and slaughterhouses, such as meat, eggs, chicken skin, and animal fat [77]; starch residue from the starch industry; de-oiled seed cakes from the edible oil industry; and molasses/black treacle from the sugar industry.Among many agro-industry wastes, sugarcane bagasse is the most prevalent.This bagasse is the dry pulpy fibrous residue generated by enterprises following the extraction of juice.About 180 million tonnes of sugarcane bagasse are thought to be available in the world [78].Orange peel, apple pomace, and fruit wastes from the production of fruit juice, cider, and other food processing units are other examples of agro-industry wastes.Products from non-food agro-industries like de-oiled seed cakes from non-edible oil plants like Pongamia pinnata and Jatropha curcas are also included in the category of agro-industry waste [79].

Livestock Wastes
Millions of rural households around the world rely on livestock and crop production for a living.It is feasible and popular in some communities to use animal dung as a source of energy to produce biogas or to simply make manure cakes for burning [80].Typical examples include using animal slurry as fuel for combined heat and power generation, burning chicken litter as fuel, and digesting animal slurry.However, in many instances, these projects are only financially viable if a market can be found for the heat produced (e.g., for use at nearby manufacturers) and the by-products (e.g., fertilizers for farms).Waste heat can be used on the farm or in neighboring areas where it can be reticulated or piped [81].

Fruit and Vegetable Wastes (FVWs)
FVWs are residual fruits and vegetables that have not been processed.Examples include tomatoes, oranges, mangoes, jackfruit, pineapple, bananas, and many more.FVWs produced by wholesale markets and the food processing sectors are huge [70].These organic wastes are also extremely perishable, which raises serious concerns about environmental pollution.According to statistics, about 15, 32, 6.5, and 1.8 million tonnes of trash are produced from the production, packaging, distribution, and consumption of fruit and vegetables in the US, China, Philippines, and India, respectively [70].Currently, roughly 5.6 million tonnes of FVWs are manufactured annually in India and dumped outside of cities [82].

Composition of Agro-Wastes
The compositional study of feedstock focuses primarily on lignocellulosic content, such as cellulose, hemicellulose, and lignin, and biochemical content, such as total carbohydrates, protein, lipids, etc. Bio-alcohols are produced as a result of the greater cellulose and hemicellulose content.Approximately 30% to 50% of cellulose and 20% to 38% of hemicellulose make up the crop residues.In contrast, the lignin concentration of crops ranges from 7% to 21%.Depending on the varied sources of origin, agro-processing wastes comprise a wide range of cellulose (21% to 45%), hemicellulose (15% to 33%), and lignin (5% to 24%).Rice bran waste contains just 5% lignin and has been demonstrated to be a viable feedstock for bioethanol production.Prior to ethanol production, however, highlignin-content sugarcane bagasse must be processed for lignin removal [83].Bio-hydrogen, biogas, and alcohols can be produced from a carbohydrate-rich substrate because of their quick breakdown.Between 40% and 85% of the total solids in industrial wastes are made up of carbohydrate compounds.Similarly, livestock wastes such as cattle manure have a carbohydrate content of 50-60%, making it an excellent fuel for biogas production because of its abundance [84].Similarly, the protein and lipid levels of various agricultural waste feedstock are critical for determining their biogas potential [85].Nano-biotechnology has been utilized in the field of antimicrobial research in order to delve into the depths of scientific complexities that are contained within the boundaries of medical practice.It has been demonstrated that NPs possess powerful antimicrobial properties, which allow them to combat superbugs that are highly resistant to antibiotics.In order to produce NPs that are capable of destroying multidrug-resistant bacteria and fungi, scientists have taken advantage of the synergy effect created by the relationship between the precursor (metal) and plants (capping/reducing agent).Table 1 displays the anti-microbial characteristics of NPs that were manufactured from agricultural by-products.

Bio-Synthesis of NMs from Agro-Wastes
Utilizing agricultural waste resources is a sustainable technique of synthesis that allows for the efficient management and usage of plant wastes and biomass [92].NPs have been successfully synthesized by varieties of agro-wastes like corn cob, rice bran, fruit seeds, wheat bran, peels, palm oil mill effluent, etc. [16,93,94].NPs production can occur intracellularly or extracellularly.The size and type of NPs are greatly influenced by the synthesis time, growth temperature, and pH [95].These agricultural wastes are a rich source of biomolecules like proteins, phenolics, and flavonoids that can act as reductant agents in the environmentally friendly production of various metal NPs.Agro-waste has been used in several biotechnological techniques to enhance the nutritional properties through solid-state fermentation (SSF), the production of enzymes [96], organic acids [97], and as renewable materials for the production of biogas [98].The synthesis route of NPs from agrowaste is shown in Figure 2. NPs can be created using a wide range of methods as of right now.However, they can be created using the "top-down" and "bottom-up" approaches, which are the two basic techniques.The first method uses a top-to-bottom strategy to break larger particles down into progressively smaller dimensions and a variety of forms; such processes include mechanical milling, laser ablation, chemical etching, electrochemical explosion, lithography, attrition, etc.The second strategy is a bottom-up strategy in which smaller components are used to make larger NPs such as atoms, monomers, and molecules, etc.The constituent atoms and molecules that make up a structure come together and self-assemble precisely where they are needed in the bottom-up method.A variety of processes, including pyrolysis, plasma, chemical vapor deposition, the sol-gel process, spinning, biological methods, atomic condensation, etc., use a bottom-up approach, shown in Figures 2 and 3.
the sol-gel process, spinning, biological methods, atomic condensation, etc., use a bottomup approach, shown in Figures 2 and 3.   the sol-gel process, spinning, biological methods, atomic condensation, etc., use a bottomup approach, shown in Figures 2 and 3.Although gold has always been a subject of fascination, the development of nanotechnology has dramatically increased the number of uses for metal.Au-NPs in particular have high levels of biocompatibility and non-toxicity.Since gold is not oxidized, it can also be used for long-term biomedical applications.It has been discovered that Au-NPs enhance the therapeutic and sensing functions of proteins and antibodies.Au-NPs have been investigated for a variety of uses, including anti-coagulant, bio-imaging, anti-oxidant, thrombolytic, anti-cancer, photo-thermal, fluorescent, catalytic, bio-labelling, anti-bacterial, and bio-sensing.Numerous physical and chemical processes have successfully produced well-defined Au-NPs, but they are expensive and require the use of toxic materials.Additionally, the chemical manufacture of Au-NPs may cause hazardous compounds to adhere to the surface of the particles, which could have detrimental effects in medical applications [86,99].Therefore, creating NPs from microbes or plant-based materials can be advantageous.Biomolecules released by biomass act as a reducing and capping agent, resulting in the creation of NPs that are more biocompatible and removing the need for abrasive chemical processes.Agro-wastes, such as banana and custard apple peels, which are abundant in phenolic components like lignin and pectin, are currently being investigated for the creation of various NPs [100,101].As the population grows, so does the demand for agro-industry products to fulfill the rising demand; massive volumes of food products are created, producing significant amounts of agro-industrial waste in the process.To create and characterize Au-NPs, scientists used watermelon rind extract [102].The produced Au-NPs showed strong synergistic action and anti-bacterial efficacy against food-borne pathogens.Additionally, it demonstrated strong anti-oxidant and proteasome inhibitory activity.The production of Au-NPs using agro-wastes is therefore presented as an environmentally friendly method, making them a possible candidate for usage in biomedical, pharmaceutical, cosmetic, food, and drug delivery applications [103].

Palladium Nanoparticles (Pd-NPs)
Pd-NPs have also been synthesized from Annona squamosa peel extract.In this experiment, 10 mL of aqueous extract and 80 mL of 1 mM palladium acetate were combined and heated to 60 • C for 4 h.XRD, UV-Vis spectrophotometer, and TEM were used to characterize the produced particles.Pd-NPs with an average size of 100 nm and spherical form were confirmed.The watermelon rind aqueous extract was used as a capping and reducing agent for Pd-NPs.The importance of the extract's polyhydroxyl groups in the synthesis of Pd-NPs was further established.The Pd-NPs with a mean size of 96.4 nm and a polydispersity index of 0.243 exhibited potential industrial catalytic application by the Suzuki coupling of aryl halide with phenylboronic acid at ambient temperature [104,105].

Platinum Nanoparticles (Pt-NPs)
Dauthal and Mukhopadhyay [106] have reported employing Punica granatum peel extract for the production of Pt-NPs with a size between 16 and 23 nm; the produced particles were crystalline and spherical.The particles' negative zeta potential showed that they were very stable.The capping and stability of the produced particles were due to, according to the FTIR study, peel extract polyphenolic compounds and their quinones, which contain hydroxyl and carbonyl functional groups.By eliminating the man-made contaminant 3-nitrophenol by NaBH 4 , the particles demonstrated good catalytic activity.The creation of polydispersed, spherical, 23 ± 2 nm-sized TiO 2 -NPs was another successful application of the Annona squamosa extract [107].

Silicon Nanoparticles (Si-NPs)
The second most common element on Earth, after oxygen, is silicon, and agriculture has begun to place a high value on this element [108].Si is regarded as a transitional element for plants, falling somewhere between an essential and non-essential category because it is not only necessary for plant existence but also provides adequate benefits when present [109].These NPs have the ability to interact with plants both directly and indirectly, resulting in morphological and physiological alterations that impart stress resistance.This enhances plant growth, boosts biomass, changes architecture and physiology, modulates tissue differentiation, activates defense mechanisms, and aids in acclimating to stressful situations in plants [110].When administered at varying concentrations, Si-NPs displayed anti-stress benefits against moderate to severe drought stress in Hawthorns (Crataegus sp.) [111].
The seedlings' responses varied depending on the concentration.Increased membrane electrolyte leakage; relative water content; improved photosynthetic capacity; and higher concentrations of chlorophylls, carotenoids, and proline are some of these consequences.
The use of nano-SiO 2 by accumulating proline increased tolerance in saline environments by maintaining ionic balance, enhancing the antioxidant system, and increasing the level of different phytopropanoids, which in turn caused osmotic adjustments.Furthermore, silicon dioxide nanoparticles are demonstrated to improve water use effectiveness, stomatal conductance, transpiration rate, and lowered chlorophyll degradation during salt stress, resulting in tolerance to external insult [112].The epicuticular wax layer has undergone major alterations, and the main cause is salt stress [113].
Surprisingly, strawberry plants treated with nano-Si had superior epicuticular wax thickness and structure than salt-stressed plants [114].Another study that looked at the effects of nano-Si to reduce salt stress on sweet pepper plants found substantial differences between them and their bulk equivalent [115].The plants received low concentrations of nano-Si (1.0 & 2.0 cm 3 /L) via irrigation for weeks, which improved the leaves and fresh weight.On potato plants subjected to various salt stresses, the SiO 2 -NPs concentrationdependent impact was also noted (NaCl, 50 & 100 mM).Both a lower concentration (50 mg per liter) and a greater concentration (100 mg per liter) of the NPs allowed them to demonstrate improved stress reduction [116].However, smaller concentrations were discovered to be more beneficial.This research significantly provides a better perspective on the positive and negative influence of NPs, challenging the preconceptions that only hazardous elements of NMs exist.As a result, before using NPs in any sector, it is necessary to first investigate their properties [117].
In times of external stress, plant hormones are essential for promoting better adaptability to a variety of shifting environmental conditions.Gibberellin, a plant growth hormone, plays a key role in how plants respond to a variety of abiotic challenges, such as drought, shade, flooding, and cold temperatures, mostly by slowing down plant development and shifting the emphasis to coping with stress.By using NMs, plant hormones can also be delivered to the plant [110].For instance, the Arabidopsis thaliana plant was tested using Mesoporous Silica-NPs that contained abscisic acid [118].The prolonged hormone release was clearly demonstrated, and the seedlings' capacity to withstand drought was also strengthened.

Silver Nanoparticles
Nanotechnology has piqued the curiosity of many people because of its numerous uses in technological domains.Metal NPs such as silver, gold, iron, zinc, cadmium, graphene, and platinum have been employed in optical, catalytic, antibacterial, and biological activities.Because of their unique qualities, such as shape, size, optical, electrical, and magnetic properties, silver nanoparticles are widely used in coated materials, sensingmaterials, electrical components, antimicrobial applications, and composite fibres [119].NPs have superior physiochemical capabilities because of their high volume ratio to surface area ratio, which can be employed for a number of applications such as antibacterial, antioxidant, and industrial wastewater treatment [120].Researchers have been inspired to create NPs via physical, chemical, and biological means since the attributes of NPs are mostly based on their structure, size, and biological composition.Physical and chemical methods typically cost money and demand a lot of energy, pressure, and heat [121].The chemicals used in the process are potentially dangerous to the environment and poisonous.As a result, there is a constant need for the creation of eco-friendly processes for producing NPs without the use of dangerous chemicals.There are now several ways to create NMs, but due to their many uses, particularly in the removal of dangerous and harmful compounds, biological processes are becoming increasingly significant [122].Plant extract is frequently used to create metal and metal oxide NPs because it has capping and reducing properties [123].

Carbon-Based NMs Carbon Nanoparticles (C-NPs)
The production of C-NPs using currently used technology is known to require considerable use of premium feedstock's in addition to expensive catalysts and required energy to drive C-NPs synthesis.A common technique for producing C-NPs on an industrial scale at a large scale is chemical vapor deposition (CVD), which is known to use a variety of costly supplies of ethylene and carbon monoxide [124].The majority of developing nations contribute agricultural fibre, and they also use a significant percentage of their agricultural waste as fuel.Goods like rice husk, groundnut shell, bagasse, and coconut fibre are used, and India contributes over 400 tonnes of agricultural waste on its own.It is recognized that the above-mentioned agricultural waste items can produce carbon compounds with nanostructures.C-NPs can be used for a variety of things, such as capacitors and high-performance electrode materials for batteries; they are also well-known for being employed as spectacular photo-luminescent materials [125].For C-NPs that have a higher surface area, efficient molecule binding is achievable.One of the processes for producing activated carbon has been called carbonization, and it involves raising temperatures to 600-900 • C while using inert gases like argon and nitrogen to produce activated carbon from raw materials like coal, nutshells, and wood.Another method is called "oxidation," which involves heating the carbonised material at a temperature between 600 and 1200 • C in the presence of oxidizing gases such as oxygen, carbon dioxide, or steam [126,127].Black carbon might technically be used to describe carbon measured by light absorption [128].It is recognized that various sources produce various forms of carbon.Diesel engines and the burning of wood and coal on a domestic and industrial scale using heavy oils are the main sources of black carbon emissions.These are made by burning agricultural waste that remains after forest fires.The formation of a point defect in a diamond particle, continuing laser ablation of graphite with oxidation and functionalization, and thermal degradation of organic compounds are all required for the creation of C-NPs using ion beam radiations [129][130][131].

Zinc and Nickel Oxide Nanoparticles
Rambutan peels were used to create biogenic zinc oxide nanocrystals in the following ways: zinc nitrate hexahydrate was reacted with Rambutan peel extract at 80 • C for two hours to produce the zinc ellagate complex.The zinc ellagate complex was subsequently oven dried for 8 h at 40 • C and then calcined at 450 • C in a muffle furnace to produce zinc oxide nanocrystals.Standard characterization investigations, including XRD, SEM-EDX, XPS, and FTIR, were used to establish that the p-track conjugation effect of zinc oxide nanocrystals promoted polyphenol production.Because of the growing ZnO nanocrystals' adsorption on the cotton surface, the cotton fabric treated with zinc oxide nanocrystals showed exceptional anti-bacterial activity against E. coli (18.5 mm) and S. aureus (23 mm) [132].
According to a related study, Yuvakkumar et al. [133] also successfully synthesized nickel oxide (NiO) nanocrystals using rambutan peels to produce nickel-ellagate complexes for the first time.The extract's polyphenols helped nickel nitrate hexahydrate transform into NiO nanocrystals.The strong antibacterial activity of 25 and 35 mm against E. coli and S. aureus, respectively, were demonstrated using cotton fabric coated with synthetic NiO crystals.

Iron Oxide (Fe 3 O 4 ) Magnetic Nanoparticles
The extracted rind of watermelon was used in a reaction of sodium acetate and iron chloride with constant stirring at 80 • C for three hours to produce Fe 3 O 4 magnetic nanoparticles [134].UV-Vis spectrophotometer, AFM, XRD, DLS, FTIR, and TEM were used to describe the spherical-shaped biogenic particles, which ranged in size from 2 to 20 nm and had a strong magnetic response.With extremely good yields of 94%, the particles created by the extract's polyphenols showed exceptional catalytic activity in the synthesis of 2-oxo-1,2,3,4-tetrahydropyrimidine derivatives.The creation of iron oxide magnetic nanoparticles using plantain peel extract was also reported by Venkateswarlu et al. [135] in a similar manner.Using common analytical methods, the biogenic particles were identified.The particles had a sphere-like form and were evenly scattered.Their size, as determined by TEM, was less than 50 nm.The bio-produced Fe 3 O 4 magnetic nanoparticles had a saturation magnetization of 15.8 emu/g and demonstrated exceptional magnetic properties [136].The different synthesis of NMs by agro-waste is shown in Table 2.There are other NPs that exert their effects through different pathways including gene regulation but we have only discussed the anti-oxidative actions of those NPs that scavenge reactive oxygen species (ROS) produced in response to stress in plants.As an illustration, TiO 2 -NPs exposure (0.01%) enhanced the amount of chlorophyll and biomass by inducing anti-oxidant enzyme activities, which reduced malondialdehyde and hydrogen peroxide and boosted the formation of proline and soluble carbohydrates, maintaining the osmotic equilibrium [179,180].Similar to this, nano-titanium dioxide was able to promote the expression of a certain important non-coding or nonsense RNA thought to be crucial to the mechanism of resistance to abiotic stress [181].
Lack of water poses a serious problem for plant production because it reduces plant vigour and severely harms crops.By raising the movement of the nitrate reductase (NR) enzyme, which in turn promotes the accumulation of osmolytes, nano-TiO 2 can help the plant's hydration status [182].Nitric oxide (NO) is produced as a result of the enhanced NR enzyme activity, and this in turn triggers the creation of proline and glycine betaine(GB) [183].TiO 2 -NPs frequently exhibit a defensive mechanism against stress in plants that is both enzymatic and non-enzymatic.It is interesting to note that TiO 2 -NPs are recognized for controlling other enzymes like glutamate hydrogenase and glutamine synthase, which results in the accumulation of additional nutrients and the creation of essential oils [184].In order to assess the impact of nano-titanium dioxide (0, 50, 100, and 200 mg/L) on Moldavian balm (Dracocephalum moldavic) plants cultivated under aggravated salinity stress, Gohari et al. conducted a greenhouse experiment (0, 50, and 100 mM NaCl) [185].Under standard conditions, the plants treated with TiO 2 (100 mg/L) produced 1.19% more of the essential oil's geranial, zcitral, geranyl acetate, and geraniol.This suggested that aromatic plants could be protected from the stress situation by directly altering the profile and composition of their essential oil production.Another investigation on medicinal plants demonstrated that the effects of drought stress were lessened by adding methyl jasmonate (200 M), salicylic acid (100 M), and titanium dioxide nanoparticles (20 ppm) [186].The outcomes indicate that this improves water stress tolerance by enzymatic and non-enzymatic anti-oxidant defense systems.

Silica-Nanoparticles (SiNPs)
Wastes created by various agricultural activities are one of the cheapest sources for the synthesis of SiNPs, and different agricultural waste comprises around 50-90% SiO 2 .Because of the lower cost of raw materials and higher silica content, agro-waste has the potential to be used for the large-scale manufacture of SiNPs.For the extraction of bound silica from agricultural waste, several physical, chemical, and biological processes are used.The extraction of silica from its source is required for the commercial manufacturing of SiNPs. Figure 4 depicts various sources that could be employed as precursor materials (clay, industrial waste, algal biomass, and plant biomass, for example) in the production of SiNPs.The conditions maintained at the time of synthesis dictate the size of NPs, and the size of SiNPs typically ranges from 10 to 500 nm [187].Three different forms of SiNP were found in one study when analyzing the bioavailability of SiNPs in invivo conditions: short rod (NSR), long rod (NLR), and spherical (NS) [188].In a study conducted by a different team of researchers, NSR and NLR shapes were also confirmed [189].The additional geometries in which SiNPs can be made include nano-ribbons, nano-helices, nano-tubes, and nano-zigzags [190].However, in order to achieve the smallest interfacial surface area, amorphous SiNPs often take on the most common spherical shape [191].In a work conducted by Akhayere et al. [192], spherical magnetic SiNPs with an average size of 162 nm were obtained from barley husk waste and utilised to remove petroleum, and its byproducts from water sources also discovered spherical SiNPs in corn cobs [193].Because of their spherical form, these NPs tend to agglomerate, allowing pollutants to be effectively absorbed at different layers.
cause of their spherical form, these NPs tend to agglomerate, allowing pollutants to be effectively absorbed at different layers.
Numerous precursors serve as pollutants on the surface of value-added products derived from biological substrate digestion [194].Therefore, silica extraction employing biological agents has gained popularity in recent years [195].Biological approaches for NP extraction are recommended over thermal and chemical procedures due to their reduced toxicity, environmental safety, and speed and ease of isolation [196].As a result, numerous researchers have concentrated on the biological synthesis of nano-silica as a unique way for the production of different NMs.In one study, California red worms were used to decompose rice husks and create micro silica [197].The worms were fed rice husks for five months; following which, the humus they expelled was neutralized with calcium carbonate and calcined at various temperatures (500, 600, and 700°C) prior to being digested with a mixture of HCl and HNO3 in a ratio of 1:3.Depending on the calcination temperature, nano-silica between 55 and 250 nm in size was generated.According to these studies, in order to obtain a single NP, the calcination temperature must be less than 600°C [195].To create NPs, they used a combination of biological, chemical, and physical methods.Aside from that, a recent study has indicated that proteins derived from marine diatoms and sponges, such as silaffins, silicatein, and polyamines, are important biomolecular in the biomimetic silicification process and can be used to synthesize SiNP [198].Silaffins and long-chain polyamines (LCPAs) form the key important factor in the bio-silicification process, converting silicon ions to nano-silica [199].A stage in the extraction of nano-silica from rice straw is shown in Figure 5. Numerous precursors serve as pollutants on the surface of value-added products derived from biological substrate digestion [194].Therefore, silica extraction employing biological agents has gained popularity in recent years [195].Biological approaches for NP extraction are recommended over thermal and chemical procedures due to their reduced toxicity, environmental safety, and speed and ease of isolation [196].As a result, numerous researchers have concentrated on the biological synthesis of nano-silica as a unique way for the production of different NMs.In one study, California red worms were used to decompose rice husks and create micro silica [197].The worms were fed rice husks for five months; following which, the humus they expelled was neutralized with calcium carbonate and calcined at various temperatures (500, 600, and 700 • C) prior to being digested with a mixture of HCl and HNO 3 in a ratio of 1:3.Depending on the calcination temperature, nano-silica between 55 and 250 nm in size was generated.According to these studies, in order to obtain a single NP, the calcination temperature must be less than 600 • C [195].To create NPs, they used a combination of biological, chemical, and physical methods.Aside from that, a recent study has indicated that proteins derived from marine diatoms and sponges, such as silaffins, silicatein, and polyamines, are important biomolecular in the biomimetic silicification process and can be used to synthesize SiNP [198].Silaffins and long-chain polyamines (LCPAs) form the key important factor in the bio-silicification process, converting silicon ions to nano-silica [199].A stage in the extraction of nano-silica from rice straw is shown in Figure 5.

Fourier Transform Infrared Spectroscopy (FTIR)
In FTIR spectroscopy, energy and matter interact with one another.It is feasible to determine the functional groups that are present and describe the sample's chemical structure by recording the quantity of absorbed energy and comparing it to a database.Nondestructive and highly effective, FTIR spectroscopy can be used to study the chemical and physical characteristics of lignocellulosic biomass [200].There are three main parts that make up plant fibre: cellulose, lignin, and hemicellulose.Alkanes, esters, aromatics, ketones, and alcohols with diverse functional groups that contain oxygen make up the majority of these materials.FTIR has been extensively used in the literature to confirm the removal of amorphous sections like hemicellulose and lignin from the fibre matrix after chemical treatments like alkali treatment and bleaching or to evaluate if extracted cellulose nanofibres contain any lignin or hemicellulose [201].In the past, scientists have studied at the infrared spectra of cellulose, hemi-cellulose, and lignin [202,203].An FTIR spectroscopic examination of isorafibres after being untreated, alkaline-treated, bleached, and acid-treated was reported by Chirayil et al. [204].They discovered a peak in the spectra of all fibres at 3300 per cm, which corresponded to the OH stretching vibrations of the hydrogen-bonded hydroxyl group and indicated the fibres' hydrophilic inclination [205].
The peak at 1630 per cm was caused by the bending mode vibration of the water [206].The peak at 1228 per cm in raw fibre was caused by the smelly skeletal vibration of lignin [207].On the FTIR investigations of the CNs made from banana peel by means of enzymatic treatment, Lima et al. [208]came to similar conclusions.They were able to demonstrate that the enzymatic treatment was successful in removing hemicellulose and lignin from the matrix of the fibres.The bulk of the lignin in the banana peel cellulose nanofibres was reportedly eliminated using bleaching, as reported by Zope et al. [209].After bleaching, the vibrations at 1525 per cm (aromatic ring vibrations), 1238 per cm (guaiaryl ring

Characterisation of NMs from Agro-Wastes 6.1. Fourier Transform Infrared Spectroscopy (FTIR)
In FTIR spectroscopy, energy and matter interact with one another.It is feasible to determine the functional groups that are present and describe the sample's chemical structure by recording the quantity of absorbed energy and comparing it to a database.Non-destructive and highly effective, FTIR spectroscopy can be used to study the chemical and physical characteristics of lignocellulosic biomass [200].There are three main parts that make up plant fibre: cellulose, lignin, and hemicellulose.Alkanes, esters, aromatics, ketones, and alcohols with diverse functional groups that contain oxygen make up the majority of these materials.FTIR has been extensively used in the literature to confirm the removal of amorphous sections like hemicellulose and lignin from the fibre matrix after chemical treatments like alkali treatment and bleaching or to evaluate if extracted cellulose nanofibres contain any lignin or hemicellulose [201].In the past, scientists have studied at the infrared spectra of cellulose, hemi-cellulose, and lignin [202,203].An FTIR spectroscopic examination of isorafibres after being untreated, alkaline-treated, bleached, and acid-treated was reported by Chirayil et al. [204].They discovered a peak in the spectra of all fibres at 3300 per cm, which corresponded to the OH stretching vibrations of the hydrogen-bonded hydroxyl group and indicated the fibres' hydrophilic inclination [205].
The peak at 1630 per cm was caused by the bending mode vibration of the water [206].The peak at 1228 per cm in raw fibre was caused by the smelly skeletal vibration of lignin [207].On the FTIR investigations of the CNs made from banana peel by means of enzymatic treatment, Lima et al. [208] came to similar conclusions.They were able to demonstrate that the enzymatic treatment was successful in removing hemicellulose and lignin from the matrix of the fibres.The bulk of the lignin in the banana peel cellulose nanofibres was reportedly eliminated using bleaching, as reported by Zope et al. [209].After bleaching, the vibrations at 1525 per cm (aromatic ring vibrations), 1238 per cm (guaiaryl ring breathing with stretching C=O), and 761 per cm (C-H deformations) vanished.Karimi et al. [210] studied the FTIR of unbleached (UBNF) and bleached (BNF) kenaf bast cellulosic fibre samples and found that neither UBNF nor BNF samples contained lignin.Techniques employed for NP characterization are shown in Figure 6.
breathing with stretching C=O), and 761 per cm (C-H deformations) vanished.Karimi et al. [210]studied the FTIR of unbleached (UBNF) and bleached (BNF) kenaf bast cellulosic fibre samples and found that neither UBNF nor BNF samples contained lignin.Techniques employed for NP characterization are shown in Figure 6.

X-ray Photoelectron Spectroscopy (XPS)
XPS, also referred to as electron spectroscopy, is a technique for chemical study [211].XPS has been utilized for surface analysis on a wide variety of materials [212].XPS provides quantitative and chemical state data from the surface of the studied material [213].The XPS studies of cellulose nanofibres have been reported in very few works.Ahola et al. [214]looked at the chemistry of model films made from cellulose nano-fibrils using XPS.They made skinny and soft native cellulose model films by spin-coating cellulose nanofibril dispersions on silica substrates.They discovered that the percentage of identified substrate material (nitrogen/silicon) rises in both model films relative to the standard, indicating that the surface has been coated by cellulose nano-fibrils.Zuo et al. [215] also investigated the surface chemical composition of nano-fibrillated cellulose aero-gels and films prior to and after coating with perfluorodecyl trichlorosilane (PFOTS).The CMC fibrils' surface counterions were determined to be carbon, oxygen, and trace levels of sodium, while fluorine and silicon were present in the modified samples.They determined that PFOTS had interacted with cellulose.

Measurements of the Zeta-Potential of Agriculture-Based NPs
The zeta-potential is a significant aspect of cellulose nanofibre suspension stability.It denotes the degree of repulsion in dispersion among adjacent, similarly charged particles.The zeta-potential measurements of cellulose nano-fibre (CNs) suspensions obtained from banana peels were reported by Dominic et al. [216].They expanded the number of CN passages in the high-pressure homogenizer and obtained highly stable CN aqueous suspensions in water with zeta potential values between 16.2 and 44.2 mV.They reported the scale and zeta capability values of CNs obtained with the aid of various quantities of passages in a high stress homogenizer.Similar consequences for CNs removed from banana plant wastes had been suggested [217].They reported zeta capacity values that ranged from -20 to -40.31 mV.Surattanamal et al. [218] observed that the zeta ability of nanofibres acquired by means of chemical treatment and enzymatic remedy were -16.2 and 25.5 mV, respectively.They observed that enzymatic remedy produced cellulose nanofibres with the best zeta capacity that were greater electrically than the ones produced

X-ray Photoelectron Spectroscopy (XPS)
XPS, also referred to as electron spectroscopy, is a technique for chemical study [211].XPS has been utilized for surface analysis on a wide variety of materials [212].XPS provides quantitative and chemical state data from the surface of the studied material [213].The XPS studies of cellulose nanofibres have been reported in very few works.Ahola et al. [214] looked at the chemistry of model films made from cellulose nano-fibrils using XPS.They made skinny and soft native cellulose model films by spin-coating cellulose nano-fibril dispersions on silica substrates.They discovered that the percentage of identified substrate material (nitrogen/silicon) rises in both model films relative to the standard, indicating that the surface has been coated by cellulose nano-fibrils.Zuo et al. [215] also investigated the surface chemical composition of nano-fibrillated cellulose aero-gels and films prior to and after coating with perfluorodecyl trichlorosilane (PFOTS).The CMC fibrils' surface counterions were determined to be carbon, oxygen, and trace levels of sodium, while fluorine and silicon were present in the modified samples.They determined that PFOTS had interacted with cellulose.

Measurements of the Zeta-Potential of Agriculture-Based NPs
The zeta-potential is a significant aspect of cellulose nanofibre suspension stability.It denotes the degree of repulsion in dispersion among adjacent, similarly charged particles.The zeta-potential measurements of cellulose nano-fibre (CNs) suspensions obtained from banana peels were reported by Dominic et al. [216].They expanded the number of CN passages in the high-pressure homogenizer and obtained highly stable CN aqueous suspensions in water with zeta potential values between 16.2 and 44.2 mV.They reported the scale and zeta capability values of CNs obtained with the aid of various quantities of passages in a high stress homogenizer.Similar consequences for CNs removed from banana plant wastes had been suggested [217].They reported zeta capacity values that ranged from −20 to −40.31 mV.Surattanamal et al. [218] observed that the zeta ability of nanofibres acquired by means of chemical treatment and enzymatic remedy were −16.2 and 25.5 mV, respectively.They observed that enzymatic remedy produced cellulose nanofibres with the best zeta capacity that were greater electrically than the ones produced with the aid of chemical treatment.Li et al. [219] investigated the hydrophilicity of rice, waxy maize, wheat, and potato starch by measuring their water contact angles.The zeta-potential of starch granules was determined to be −20.5, −19.1, −20.4,and −4.2 mV for rice, waxy maize, wheat, and potato starch, respectively.With an increase in dispersion pH from 2.07 to 11.96, the zeta potential of starch nanocrystals studied by Wei et al. [220] was found to decrease from −6.7 to −34.5 mV.They also found that as the pH of the dispersion increased, the distribution peaks of the starch nanocrystals grew wider.

Thermal Analysis of NPs Obtained from Agro-Waste
Decomposition, melting, polymerization, crystallization, and oxidation are just some of the chemical changes that can be detected through thermal analysis.Thermal analyses are methods that have been developed to determine the kinetics of the thermal degradation and the thermal transformation of agricultural waste NPs, both of which can be used to define the operating conditions for employing these materials in fields as diverse as the chemical and the environmental.

Nanocellulose and Micro Cellulose Derived from Agro-Waste
Raw pineapple leaves were subjected to alkali treatment, bleaching, acid treatment, and neutralization to extract micro cellulose.Ogah et al. investigated the thermal stability of various agro-nanofibres (rice hull, corncob, flax shive, walnut shell) in order to determine the decomposition of cellulose, hemicellulose, and lignin [221].Thermo gravimetric measurements were taken at heating rates between 5 and 20 • C per min.The agricultural fibres' weight loss and derivative losing weight curves demonstrated that the first step correlates to moisture evaporation, with hemicellulose degradation occurring next between 180 and 300 • C because of its brittle branched-chain structure.Because of its thermally stable linear chain structure, cellulose decomposes between 290 and 360 • C. Lignin is the final decomposition from 300 to 500 • C. The highly cross-linked and complex structure accounts for the wide temperature range of its decomposition.The use of diverse agricultural wastes for the extraction of nanocellulose is regarded as a sustainable strategy, with these wastes classified as lignocellulosic biomass, which mostly contains lignin, cellulose, and hemicellulose [222].Nanocellulose extraction from lignocellulosic biomass is typically separated into two stages.The first stage involves extracting hemicellulose, lignin, and other non-cellulosic components from biomass.The second step is to remove nanocellulose from cellulosic fibrils using various chemical, biological, and mechanical approaches [223].Figure 7 depicts a flow chart of a short nanocellulose extraction approach from lignocellulosic biomass.

Cellulose Nanofibrils (CNF)
Microwave liquefaction was used by Xie et al. [224] to study the characteristics of cellulose nanofibrils obtained from bamboo.In a nitrogen atmosphere, 2 mg of the sample were heated to 800 • C at a rate of 20 • C/min.The weight loss curves that were obtained demonstrate typical results of the literature with various steps, as mentioned above in the study by Xu et al. [225].The maximum decomposition rate temperature can be determined from the weight loss curve's derivative; this can be computed using a formula called the derivative of time (T max ).The temperature at which the cellulose in the original bamboo begins to break down is known as the T max .For the microwave-liquefied residue sample at 25 • C, the derivative weight loss curve allows for the observation of the decline in this temperature.This decline can be explained by the bamboo's fragmented structure during microwave treatment.It is essential to employ losing weight curves and their related derivative weight loss curves in order to understand the events that may happen during heat therapy.Endoglucanase pre-treatment enhances the disintegration of cellulosic wood fibre pulp into cellulose nanofibres, according to Padhi et al. [226].Lima et al. [208] extracted cellulose nanofibres from banana peel bran using chemical treatment (alkaline treatment, bleaching, and acid hydrolysis) and enzymatic treatment (alkaline treatment and xylanase hydrolysis).Chemically and enzymatically treated nanofibres had average diameters of 10.9 and 7.6 nm and lengths of 454.9 and 2889.7 nm, respectively [227].They demonstrated that the NPs that were separated from both treatments may be used as reinforcement in composites.

Cellulose Nanofibrils (CNF)
Microwave liquefaction was used by Xie et al. [224] to study the characteristics of cellulose nanofibrils obtained from bamboo.In a nitrogen atmosphere, 2 mg of the sample were heated to 800°C at a rate of 20°C/min.The weight loss curves that were obtained demonstrate typical results of the literature with various steps, as mentioned above in the study by Xu et al. [225].The maximum decomposition rate temperature can be determined from the weight loss curve's derivative; this can be computed using a formula called the derivative of time (Tmax).The temperature at which the cellulose in the original bamboo begins to break down is known as the Tmax.For the microwave-liquefied residue sample at 25°C, the derivative weight loss curve allows for the observation of the decline in this temperature.This decline can be explained by the bamboo's fragmented structure during microwave treatment.It is essential to employ losing weight curves and their related derivative weight loss curves in order to understand the events that may happen during heat therapy.Endoglucanase pre-treatment enhances the disintegration of cellulosic wood

Nanocrystals and Nanofibres
Robles et al. [228] present a case study for the nanocrystals of chitin and cellulose.As the weight loss peak moves to elevated temperature, this indicates that the composite's thermal resistance has improved.Different studies are about the decomposition of cellulose/starch [229,230], but as shown by Sun et al. [231], thermal analyses are also utilized to assess nanocrystals and nanofibres derived from agricultural wastes in order to determine decomposition processes and temperatures.

Parameters of Kinetics
Numerous authors have demonstrated that kinetic variables of agricultural waste NM thermal decomposition can be estimated from thermal analysis [100,[102][103][104]. Equation ( 1) can be used to describe the rate of thermal decomposition.
where t is the period of time required for the reaction to occur, k(T) is a constant, and f(α) is a function that changes depending on the type of material being converted.The current conversion factor is expressed as shown in Equation ( 2): with w 0 representing the initial sample weight, w t representing the mass sample weight at time t, and w f representing the final sample weight.The mgs are the unit of measure for all sample sizes.The reaction rate constant is determined by the Arrhenius equation and can be expressed as shown in Equation ( 3): where A, E a , and R denote the pre-exponential factor, activation energy, and constant of ideal gas, respectively.From Equations ( 1)-( 3) and some integration, as Henrique et al. describe, it is possible to calculate the kinetic parameters [232].The authors employed two approaches, Kissinger and Flynn-Ozawa, to find out the conversion and activation energy of cellulose nanocrystals taken from clean mango seeds, Eucalyptus urograndis, and cellophane.An example of cellulose nanocrystals that were extracted from clean mango seeds shows that the activation energy can be very different for the same rate of conversion, depending on how the extraction was done.The Arrhenius parameters and activation energy of tropical lignocellulosic agro wastes were determined using three iso-conversional techniques, Kissinger-Akahira-Sunose (KAS), Flynn-Wall-Ozawa (FWO), and Friedman [233].It was also shown that the breakdown of cellulose, hemicellulose, and lignin followed a second order kinetic model.It was described how these models can be applied to the process of wood degradation during pyro-gasification [234].

Morphological Characterisation of NPs Derived from Agro-Waste
Morphology explores the specifics of material systems into sorts of normal shapes so that it will realize how various materials interact with each other.Morphology is also connected with macroscopic qualities, and the microstructure of polymers is associated with both the conformation and morphology of the polymer.There are numerous techniques for characterizing bio-based NMs that could be used to calculate their volume, shape, and size distribution.TEM and AFM are the typical microscopic techniques.

Atomic Force Microscopy (AFM)
In an AFM, the physico-chemical characteristics of a sample are found by moving a sharp probe on a cantilever over the sample and watching how the cantilever moves as a laser beam reflects off of it.AFM gives accurate and precise information about the size of cellulose nano-fibrils, as well as their morphology, surface topography, mechanical properties, and ability to stick to other things [235,236].Nano-cellulose particle thickness; lateral connections between nano-fibrils; nano-scale morphology and roughness; porous network structure, mechanical, optical, and permeability properties; and the shape parameter of individual particles may all be determined by this method.It has been found that the roughness of cellulose's surface affects its flow characteristics contact angle, hydrophilicity, and local mass transfer, as a membrane.AFM may also be used to analyse the nanoscale particle size distribution of cellulose fibres [237,238], and AFM images of nano-cellulose from many resources and the advantages of AFM are used in determining changes caused by various factors.AFM images of (A) starch nanocrystals, (B) cellulose nanocrystals, and (C) chitin nano-whiskers are depicted in Figure 8.
cellulose nano-fibrils, as well as their morphology, surface topography, mechanical p erties, and ability to stick to other things [235,236].Nano-cellulose particle thickness; eral connections between nano-fibrils; nano-scale morphology and roughness; porous work structure, mechanical, optical, and permeability properties; and the shape para ter of individual particles may all be determined by this method.It has been found the roughness of cellulose's surface affects its flow characteristics contact angle, hy philicity, and local mass transfer, as a membrane.AFM may also be used to analyse nanoscale particle size distribution of cellulose fibres [237,238], and AFM images of na cellulose from many resources and the advantages of AFM are used in determin changes caused by various factors.AFM images of (A) starch nanocrystals, (B) cellu nanocrystals, and (C) chitin nano-whiskers are depicted in Figure 8.

Transmission Electron Microscopy (TEM)
The image of TEM plays a crucial role in cellulose micro-fibril and nanocrystal m phological studies.TEM has traditionally been the method of choice for visualizing

Transmission Electron Microscopy (TEM)
The image of TEM plays a crucial role in cellulose micro-fibril and nanocrystal morphological studies.TEM has traditionally been the method of choice for visualizing the morphology of individual or grouped CMCs [242].Variation in transmitted and diffracted beam intensity due to microstructural changes on the electron route that alter diffraction conditions is the origin of image contrast.The TEM images of (A) starch nanocrystals, (B) chitin nanocrystals, and (C) cellulose nanocrystals are shown in Figure 9.However, there are a few things to keep in mind when using TEM to characterize NPs.It is critical to check whether a satisfactory dispersion of NPs has been obtained while characterizing TEM.morphology of individual or grouped CMCs [242].Variation in transmitted and diffracted beam intensity due to microstructural changes on the electron route that alter diffraction conditions is the origin of image contrast.The TEM images of (A) starch nanocrystals, (B) chitin nanocrystals, and (C) cellulose nanocrystals are shown in Figure 9.However, there are a few things to keep in mind when using TEM to characterize NPs.It is critical to check whether a satisfactory dispersion of NPs has been obtained while characterizing TEM.

Nano-Biosensors
Nano-biosensors (NBSs) are analytical tools with a minimum dimension of 100 nm or less [123].NBSs are created to monitor plant fractions, soil, water, and NPs as well as nanotubes, nanowires, or nanocrystals in the agro-ecosystem [246].In comparison to current analytical sensors and biosensors that integrate biological element detection with chemical or physical principles, NBSs provide a powerful tool by utilizing the physicochemical characteristics of NMs.A transducer transforms biological data into a signal that an electrical component can produce.With this capability, an agronomist can accurately and quickly monitor the crops' nutritional and water needs as well as any early signs of disease [247].For plant science research, high-resolution crop monitoring with nano-biosensors may be a highly helpful instrument [248].The real-time continuous measurement of plant metabolites and hormones will provide unprecedented levels of insight into and control over plant biosynthetic pathways [249].

Use of Nano-Fertilisers
Despite great expectations, the industrial manufacturing of nano-fertilizers on a wide scale and their use has not yet materialized.This is unquestionably a result of the unclear legislative direction.For instance, the European Union is actively working on developing a legislative and regulatory framework.Another contentious point is that, unexpectedly, it is simple to confirm that research has ignored macronutrients in favour of micronutrients when we examine the current literature.This is notable since crop output is actually  Nano-biosensors (NBSs) are analytical tools with a minimum dimension of 100 nm or less [123].NBSs are created to monitor plant fractions, soil, water, and NPs as well as nanotubes, nanowires, or nanocrystals in the agro-ecosystem [246].In comparison to current analytical sensors and biosensors that integrate biological element detection with chemical or physical principles, NBSs provide a powerful tool by utilizing the physico-chemical characteristics of NMs.A transducer transforms biological data into a signal that an electrical component can produce.With this capability, an agronomist can accurately and quickly monitor the crops' nutritional and water needs as well as any early signs of disease [247].For plant science research, high-resolution crop monitoring with nano-biosensors may be a highly helpful instrument [248].The real-time continuous measurement of plant metabolites and hormones will provide unprecedented levels of insight into and control over plant biosynthetic pathways [249].

Use of Nano-Fertilisers
Despite great expectations, the industrial manufacturing of nano-fertilizers on a wide scale and their use has not yet materialized.This is unquestionably a result of the unclear legislative direction.For instance, the European Union is actively working on developing a legislative and regulatory framework.Another contentious point is that, unexpectedly, it is simple to confirm that research has ignored macronutrients in favour of micronutrients when we examine the current literature.This is notable since crop output is actually primarily impacted by N, P, and K nutrition-despite the fact that microelements are crucial to plant metabolism [250].
In conclusion, there are still a lot of high expectations to live up to.According to international and national organizations (FAO, UNEAP, USEPA, and EEA) concerned with sustainable agricultural development and food security, applied research on nanotechnology in agriculture should be reoriented in accordance with clear priorities [251].One of these priorities is unquestionably the creation of N and P nano-fertilizers.

Nano-Fungicides
The majority of agricultural damage, including that to important crops such asrice, wheat, barley, groundnuts, and cotton, is caused by fungi [252].These illnesses have an impact on society since they severely reduce crop productivity and the economy.Fungicides that are commonly used can reduce these losses, but they can harm biodiversity because they target a wide variety of living things.As a result, we must consider other strategies to improve the management of fungal diseases.The creation of NPs as a successful tactic against fungal diseases is one of the greatest methods.Ag-NPs are frequently utilized for disinfection due to their antibacterial characteristics [253].The efficiency of Ag-NPs and Ag-ions against the plant-pathogenic fungi Magnaporthe grisea and Bipolaris sorokiniana was tested in an experiment.When used for three hours, the ionic and nanoparticulate versions dramatically lessened the severity of the condition and were effective against the fungi [254].Both Cu-NPs and Ag-NPs have the ability to inhibit the growth of the fungi Alternaria alternata and Botrytis cinerea.Rhizopus stolonifer, Fusarium oxysporum, and Mucor plumbeus are all susceptible to the antifungal effects of ZnO-NPs and MgO-NPs [255].Two common pesticides, zineb and mancozeb, were enclosed in a MWCNT-g-PCA hybrid material; mancozeb was confirmed to be a more useful fungicide against A. alternate [256].

Adsorbents
Rice husk, an agricultural by-product, was used as a precursor for the synthesis of silica NPs [257].XRD and SEM were utilized to investigate the specific characteristics of synthesized NPs [258].As an adsorbent, Fe 3 O 4 @n-SiO 2 nanoparticles were used to remove Cr(VI) from an aqueous solution [259].Results showed that Cr (VI) ion removal was greatest at a pH of 2.0.As the initial concentration of Cr(VI) was increased from 1.36 × 10 −2 M to 2.4 × 10 −2 M, a corresponding decrease in removal (%) was observed [259].After regeneration, the adsorbent was found to significantly remove Cr (VI) for up to six cycles (>60 ± 0.8%).However, it loses efficiency with each cycle, and its adsorption efficiency drops from 91.56 to 61.65 ± 0.08% from the first to sixth cycle [259].Regeneration suggests that using this adsorbent for chromium-rich water/wastewater can result in cost-effective treatment.

Catalyst
Gupta et al. [260] reported the use of pine needles in the synthesis of nanocomposites of nanocellulose and NiFe 2 O 4 nanoparticles.These nanocomposites were created by first synthesizing carbon nanofibres (CNF) from pine needles, then silanising these nanofibres (SCNF) with tetraethyl orthosilicate.Ni (II) and Fe(III) solutions were mixed into the aqueous CNF or SCNF mixture.After adjusting the pH of this mixture to 7.5 and stirring it for 2 h, it was hydrothermally treated at 160 • C to make nanocellulose/NiFe 2 O 4 nanocomposites.Researchers found that SNCF-supported NiFe 2 O 4 (NiFe 2 O 4 @SCNF) works well as a catalyst for the oxidative breakdown of Remazol Black 5 (RB5) and the reduction of nitrophenols.Titanium oxide nanoparticles with a size of 10 nm that were supported on hazelnut shell-or olive residue-activated carbon were recently prepared by Donar and colleagues [261] for use as a photocatalyst in the photodegradation of methylene blue.Honey pomelo peel-derived porous carbon was utilized in the synthesis of NiCo 2 O 4 nanocomposites by Guo et al. [262].After mixing a solution of Ni(II), Co(II), and urea with porous carbon and then subjecting the mixture to treatment at 120 • C, carbon-supported NiCo 2 O 4 nanosheets were produced.

Battery
The lower-temperature carbothermal or magnesiothermic reduction of amorphous silica found in rice husks could produce crystal silicon for use in battery materials (such as lithium-ion batteries) [263].The conventional method of manufacturing silicon results in higher costs than alternative methods.As a result, a significant amount of effort is being put towards the development of a process that is low in cost, high in volume, and commercially viable for producing high-purity silicon for use in electrical applications [264].Numerous methods have been devised for extracting silicon from rice husk.By making silicon anode materials from biomass resources, the battery industry can make good use of agricultural waste products.As a result, it is believed that silicon anode materials with a nano/microhierarchical structure, in which CNTs are tightly intertwined between the RH-derived Si nanoparticles, are the best possible anode materials for lithium-ion batteries [263].

Health Risks and the Toxicological Impact of NPs in Agriculture
There has been a lot of study into the risks and health effects of NM, but we still don't understand them very well.There is currently no uniform set of standards for the management of risks associated with the use of NPs in the agri-food industry.To ensure nano-safety, unified regulatory frameworks have been developed with a particular emphasis on safety-by-design synthesis methods [265].To transfer information among diverse nanotechnology sectors, fields such as risk communication, risk management, policymaking, and risk assessment among many stakeholders are required.Generally, nanosafety researchers use a two-way strategy.The first strategy is to comprehend toxicity to human health, which is primarily directed at organisms, tissues, and cells.Secondly, groups worry about potential threats to their health from the environment.These communities are mostly concerned with different elements of the tree of life [266].After that, research on the safety of NMs in plants has focused on the direct or intentional contact of food crops with specific NMs (like nano-insecticides, nano-fertilizers, and nano-herbicides), as well as indirect or unintentional exposure [267].The fundamental consideration before utilizing NPs in any field is their physical and chemical characteristics, since these may directly affect their potential environmental and health dangers, hence limiting their actual potential as a useful entity.The size and concentration of the NPs are the most essential aspects from the standpoint of toxicity [268].In light of the extensive research showing that NPs as small as 5 nm can easily pass through cell wall pores and as small as 20 nm can pass through plasmodesmata, it is reasonable to assume that NPs in the lower size range can enter plants more quickly and cause greater phytotoxicity even at lower concentrations [269].The potential transfer from roots to shoots is hampered, as in the case of bigger size graphene oxide, and the bioaccumulation is lowered [270].
Recent studies have also demonstrated that phytohormones are crucial to the signaling of the external insult response.A hormone imbalance in plants is suggested by the NPs' reduction of auxins, cytokinins, and salicylic acid, which has an impact on the metabolism as a whole [271].When NP concentrations are extremely high, photosynthesis may be substantially hampered, maybe even leading to plant death.According to numerous research, exposure to NP has significantly reduced or inhibited plant development [272].
In light of the above-mentioned data, it is apparent that a number of parameters must be taken into account before realizing the beneficial exploitation of NPs in the agricultural system.The interaction between plants and soil is what drives agricultural productivity; hence it is crucial to understand the physicochemical properties of the soil system.It is thought to be the primary sink for NPs; therefore, any interactions between NPs and the soil's constituents could have a significant effect on how they turn out [273].It has been discovered that increasing toxicity is caused by pH, organic content, and cation exchange capacity.For example, pH 5.5 loamy clay soil showed negligible toxicity to ZnO-NPs even at 2000 mg/kg concentration, whereas loamy clay soil with pH 7.34 showed considerable toxicity at 45.45 mg/kg concentration [274].Furthermore, soil organic matter has an important role in changing the safety concerns of the NPs, as evidenced by the lowered toxic effects of the zinc oxide nanoparticles when given with Alginate at a dosage of 400 to 800 mg/kg [275].The biomass of plants is significantly reduced when ZnO-NPs are used in isolation, though.In addition, NPs have a direct effect on the structure of the microbial community of soil in a dose-dependent way, as seen by DNA fingerprinting analysis, which revealed declining taxa of Bradyrhizobium, Bradyrhizobiaceae, and Rhizobiales [276].However, favourable benefits for Sphingomonadaceae and Streptomycetaceae were also predicted.It is noteworthy to see that NPs are increasing the taxa of the community linked to the breakdown process of organic pollutants and biopolymers while decreasing the taxa of the community linked to nitrogen fixation [277].Ag-NPs also showed a dose-dependent effect on Rhizobium's and Azotobacter's nitrate-reduction activity, with a 0.3 ppm increase in Azotobacter's activity [278].The majority of environmental-based nano safety research has focused on preventing unintentional NP releases into the environment during the production, use, and disposal of agriculture-related nanoproducts.Studies comparing the relative toxicity of NPs-dialuminium dioxide at ZnO (15 nm), bare-ZnO (10 nm), and ZnO at KH550 (20 nm) on grown green peas have been conducted (Pisum sativum).Zn levels in seeds and roots were greater in plants treated with Al 2 O 3 at ZnO-NP (1000 mg/kg for 65 days) compared to bulk and other Zn-NP exposure [279].Photosynthetic pigments (Chl-a and carotenoid) rose considerably, but protein and carbohydrate content remained essentially constant throughout all treatments, with the notable exception of Al 2 O 3 at ZnO-NP [280].Similarly, a very high concentration of ZnO-NPs (1000 mg/L) had no effect on seed germination or root elongation.Cu and Ag-NPs, on the other hand, hindered zucchini root growth (Cucurbita pepo) [281].Plant biomass and transpiration rate were drastically reduced when exposed to Ag-NPs at concentrations of 500 and 100 mg/L, respectively [282].
Indeed, the direct release of NMs into the environment through agro-nanotechnologies and the incorporation into the human exposure pathway via the food supply chain is theoretically possible.Because of the potential movement of NMs via the food chain, which is the present problem with agricultural nano-chemical application, safety assessment is critically needed.There are several ways for humans to be exposed to nano-agrochemicals, including increased requirement for food crops, huge food waste in affluent sectors, and other agricultural operations (food crops are harvested both before and after) [283].Furthermore, because plants are widely consumed, they provide a substantial opportunity to ease the transfer of NPs to different tropic levels and, ultimately, they are important in the food chain since they are mostly ingested by different trophic microorganisms, animals, and humans [284].
It is critical to comprehend the single health notion, particularly in the context of agricultural nanotechnology.Previous studies and reports focused on the need for seeing modern health concerns via a single health concept cannot be minimized; this must be understated.Furthermore, many peer-reviewed journals portray their study findings as evidence of the need for a unified health approach.We must also recognize the outstanding efforts of various international organizations (FAO and WHO, etc.) devoted to promoting the concept of one health and raising awareness of its significance [285].

Future Perspectives
NMs have shown a growing interest in agricultural activities, likely as a direct result of the expanding research and innovations in science and engineering.NMs have also been shown to be useful in anaerobic digestion, and as such, they have the potential to be useful in the conversion of agro-biomass.In general, nanotechnology has the potential to promote and drive the next revolutions in agricultural structures; however, there is a paucity of data on the effects that these NM-enhanced agricultural structures may have on human health and the environment.Concerns have been raised regarding the effects that may result from the interactions of these NMs with foods that have been packaged.Additional research is required to address these concerns about people's health.

Conclusions
The disposal of agro-industrial and other solid wastes is another major concern in developing nations.It has been discovered that one method for effectively managing waste is to make use of agro-waste products as a source for the synthesis of nanostructured materials.It is imperative that the contemporary strategies for the synthesis of agro-wastebased, cost-effective, and environmentally friendly graphene oxide compounds receive adequate emphasis.Emerging techniques for the utilization of agro-waste and biopigments have the potential to play a significant role in the environmentally friendly synthesis of various NPs.In the applications of NMs for water treatment, bioimaging, and medication delivery, it is always essential to utilize clean materials rather than trash that could introduce hazardous chemicals.In other words, biomass wastes that may release toxins are not appropriate sources for NMs or substrates, particularly in nanotechnologies related to health and the environment.This article summarizes the various sources, characteristics, and nano-management of agro-waste.Additionally, it discusses the bio-synthesis, morphological characterization techniques, and applications of various agro-based NPs.

Figure 4 .
Figure 4. Different raw materials for commercial production of silica nanoparticles.

Figure 4 .
Figure 4. Different raw materials for commercial production of silica nanoparticles.

Figure 5 .
Figure 5.Different steps in the isolation of nano-silica from rice straw.

Figure 5 .
Figure 5. Different steps in the isolation of nano-silica from rice straw.

Figure 6 .
Figure 6.Different techniques employed for characterization of NPs.

Figure 6 .
Figure 6.Different techniques employed for characterization of NPs.

Figure 7 .
Figure 7.Flow chart of isolation process of nanocellulose from lignocellulosic biomass.

Figure 7 .
Figure 7. Flow chart of isolation process of nanocellulose from lignocellulosic biomass.

Table 1 .
Anti-microbial activities of NPs synthesized from agro-waste.

Table 2 .
Synthesis of NMs by agro-waste.