Evaluation of the Effects of Airﬂow Distribution Patterns on Deposit Coverage and Spray Penetration in Multi-Unit Air-Assisted Sprayer

: Efﬁcient utilization is a pre-requisite for pesticide reduction, and appropriate airﬂow distribution pattern plays a key role in enhancing the effectiveness of pesticide application by air-assisted orchard sprayers, yet the mechanism of this is unclear. In order to clarify the speciﬁc effects of airﬂow velocity and direction on spraying efﬁcacy, a series of spray tests on pear and cherry and airﬂow distribution tests in open areas were conducted by a multi-unit air-assisted sprayer on ten different fan settings. Several deposit indicators were analyzed and contrasted with the air distribution. The results showed that an increase in airﬂow velocity inside the canopy improved the abaxial side deposit coverage of both pear (from 3.33% to 11.80% in the Top canopy and from 6.26% to 11.00% in the Upper canopy) and cherry leaves (from 3.61% to 10.87% in the Top canopy, from 1.36% to 9.04% in the Middle canopy, and from 3.40% to 9.04% in the Bottom canopy), but had no signiﬁcant effect on the spray penetration. The correlation between deposit indicators and airﬂow velocities/directions was evaluated, and the results indicated that the enhanced airﬂow velocities, both in the forward and horizontal direction, improved the abaxial side deposit coverage ( CAB ) on the outside of pear canopy ( p < 0.001), but for cherry, none of the airﬂow indicators had a signiﬁcant impact on the CAB independently. On the other hand, the increased airﬂow direction angle in the cross-row plane for pear, as well as the increased airﬂow velocities in forward and vertical direction for cherry, both showed negative effects on the adaxial side deposit coverage ( p < 0.01). The ﬁndings in this study might be helpful to improve the performance of pesticide application in orchards, especially for abaxial side deposition, and could provide a reference for the further investigations about the effect of airﬂow on spray canopy deposition.


Introduction
The reduction of pesticide application has been a consistent proposition of the Chinese government for many years, and it has also been included in the most important national development plan [1] as a significant goal of agricultural reform several times. Normally, the efficient utilization of pesticide, which means the active ingredient should be delivered to the target precisely, uniformly, and exclusively, was considered a key way to achieve pesticide reduction.
Pear and cherry are two cash crops grown on a large scale in several provinces in China, and their market demand has been increasing year by year. Recently, several investigations on pear and cherry orchards and their managers have been conducted by our team, and it was found that several kinds of diseases and pests occurred on the abaxial side of leaves, such as Pear psylla [2] and brown rot [3], which had a serious detrimental effect on the yield and quality of the fruits. Therefore, during the pesticide application in orchard, it is necessary to ensure sufficient deposit on the abaxial side of the leaves.
For decades, the air-assisted sprayer has been recognized as a high efficiency pesticide application equipment and is widely used for disease and pest control in the orchards. The main principle of air-assisted sprayers to improve the spraying effect is that the airflow generated by the fan sends droplets into and disturbs the tree canopy to increase spray deposition and enhance the uniformity of the droplet distribution [4][5][6][7]. In recent years, the axial fan sprayer [8,9] (AAS) and air tower sprayer [10,11] (ATS) have been the most widely used orchard application equipment, due to the stability of performance and convenience of operation. Various studies have focused on the spray effect of both the two types of sprayers, and there seems to be a general consensus that the spray deposition can directly or indirectly be affected by not only the canopy structure [12], but also the physicochemical properties of pesticides [13], the meteorological conditions [14] and operation techniques [15], among others. However, in most cases, the canopy structure of trees in the orchard is relatively stable with good management, where the application of pesticides mainly depends on the type and outbreak degree of pest and disease. Furthermore, there is no doubt that the artificial control of meteorological conditions is hard to achieve. All these factors make the adjustment of sprayer operation the most direct and effective way to improve the spray effect.
To date, the influence of the operating techniques on the spray effect, including travel speed, nozzle type, spray pressure, etc., have been explored by many researchers. Salyani, M. and Whitney, J.D. [16] characterized the effects of sprayer ground speed (1.6-6.4 km/h) on spray deposition at different locations within citrus tree canopies, and the results showed that travel speed did not have a significant effect on mean deposition in the tree canopy; however, variability of deposition increased as speed increased. The spray characteristics of the nozzle play an essential role in the pesticide application, especially for spray deposition. Hence, Nuyttens, D. et al. [17] tested the droplet size spectra of 32 nozzle-pressure combinations and expounded the effect of the nozzle type, size, and pressure on the droplet size and velocity spectra. It should be emphasized that droplet velocity is important with regard to canopy penetration and leaving surface retention. On the other hand, smaller droplets, especially those less than 150 [18] or 200 µm [19] in diameter, are more susceptible to airflow. According to applications based on an axial-fan air-blast orchard sprayer made by Derksen et al. [20], the smaller droplets can provide higher coverage than larger droplets on the axial side of leaves, and the authors believed that greater air turbulence was needed to improve this. However, considering that smaller droplets also have a higher risk of off target or drift, the balance between the advantages and the risk of off-target pollution should also be taken into account [21,22].
In addition to the above factors, the impact of spray distribution pattern on the pesticide application performance cannot be ignored. According to Gil et al. [23], an adequate adjustment of spray liquid distribution to the canopy structure can reduce spray drift up to 90% and reduce pesticide use up to 20%. Li et al. [24] conducted a comparative experiment on profile variable rate spray and conventional air assisted spray in orchard, and the results showed that a 23.2% reduction of spray drift and a 67.4% reduction of ground losses happened after adjusting the spray distribution pattern, moreover, a 45.7% saving of the solution was also obtained. It is now generally accepted that the spray distribution is directly determined by and dependent on the airflow pattern [4], including airflow velocity, direction, and their distribution in space. Farooq et al. [25] evaluated the spray penetration into the citrus canopy in two different airflow rates using air-carrier sprayers, results indicated that the higher airflow resulted in a better spray penetration and a significantly larger deposition in the far section of the canopy than the lower airflow. Holownicki et al. [26] compared three axial fan sprayers with different air discharge systems in the modern orchard, including conventional, cross-flow, and a high-volume directed air-jet (HVDAS) with the air spouts directed at 20 and 40 • upwards, and the HVDAS with air spouts set 20 • upwards produced a higher canopy deposit and a lower off-target loss than the other two sprayers. Another work [27], by investigating the effects of changing the fan speeds (1400, 2000 and 2500 rpm) and the direction of the air-jet (90 and 120 • backward angle of the outlet side deflectors in relation to the treated row), studied the performance of a sprayer fitted with two vertical adjustable air outlets in vineyards, the highest deposit was observed with 1400 and 2000 rpm fan speeds and 120 • backward angled air outlets, and the high 2500 rpm fan speed improved the degree and the uniformity of the spray coverage. Proper adjustment of the airflow velocity plays a key role in the efficiency of spray application [28,29]. However, excessive airflow will also reduce the canopy deposition [30] and lead to more spray loss and drift [31]. All these studies show that proper adjustment of airflow plays a key role in the efficiency of spray application. Therefore, as a prerequisite for determining the optimal adjustment, the specific effect of airflow on spray canopy deposition should be defined.
In order to clarify the correlations of airflow velocity distribution and direction with spray deposit in different parts of the canopy, we conducted a series of spray tests in the orchard and airflow distribution tests in an open field with different unit fan parameters, which were determined by the canopy characteristics of pear and cherry. In the end, the effect of the fan unit adjustment was evaluated by analyzing the correlation between the airflow velocity and direction with the canopy deposition. These were all based on a multi-unit air-assisted sprayer independently developed by our team. Figure 1 shows the multi-unit air-assisted sprayer (MAS). The length and width of the MAS were 3.2 m and 1.5 m, the rated power of the engine is 6.3 Kw. Three units were installed on both sides of the sprayer with a fan hood depth of 150 mm. Each of the units, equipped with 20-inch carbon-fiber fan blades driven by a brushless motor, were connected to the vertical support rod by a mechanical joint that ensured the manual adjustment of installation height and tilt angle could be achieved. The rotation rate of each brushless motor could be controlled independently through a specially made control box, and both of the brushless motors and the box were powered by a 24 V storage battery (Fengfan, Baoding, China) linked to a 3.5 kW range extender to provide stable working voltage. Four hollow cone nozzles HCI4001 (ARAG, Rubiera, Italy) were equidistantly installed at the air outlet of the unit. The spray angle of HCI4001 was 40 • , the volume flow rate was 0.39 L/min, and the volume median diameter of the droplet was 121 µm at a spray pressure of 0.3 MPa. The droplet diameter was tested by Spraytech Particle size analyzers [32] (Malvern Panalytical, Worcestershire, UK) according to ISO 13320:2020 [33]. Figure 2a showed the spray test site in Haidian District, Beijing (116.19 • E, 40.15 • N), which was a plain area. The 15-years-old pear (Pyrus bretschneideri) orchard covered an area of 0.66 ha, trees were planted in a 6 m by 3 m row and tree spacing, and the average tree height was 3.1 m. The 4-years-old cherry (Cerasus pseudocerasus) orchard covered an area of 0.91 ha, the row and tree spacing were 4 m and 1 m, and the average tree height was 2.6 m. Tests were conducted in August 2021. During this period, the weather continued without rain, the temperature remained at 27.6-33.4 • C in the daytime, and the wind speed was below 1 m/s during the experiment-all of these provided a suitable meteorological condition for spraying.  Figure 2a showed the spray test site in Haidian District, Beijing (116.19° E, 40.15° N), which was a plain area. The 15-years-old pear (Pyrus bretschneideri) orchard covered an area of 0.66 ha, trees were planted in a 6 m by 3 m row and tree spacing, and the average tree height was 3.1 m. The 4-years-old cherry (Cerasus pseudocerasus) orchard covered an area of 0.91 ha, the row and tree spacing were 4 m and 1 m, and the average tree height was 2.6 m. Tests were conducted in August 2021. During this period, the weather continued without rain, the temperature remained at 27.6-33.4 °C in the daytime, and the wind speed was below 1 m/s during the experiment-all of these provided a suitable meteorological condition for spraying.

Spray Test
Five rows in the middle of the orchard were selected for application ( Figure 2b). Five consecutive trees were sampled in the middle row, and these trees were not less than 10 m from the beginning and end of the row to make sure the MAS was working stably when passing through. There were 4 layers set on each of the sample trees of pear and 5 sample points were set in each layer ( Figure 2c). There were 3 layers for cherry trees and 3 sample points in each layer. All of the layer and sample parameters, including layer height, layer width, and the distance between sample and trunk, were measured and shown in Table 1. A well-grown leaf was chosen within the area 15 cm from the sample point and 2 white art papers (60 mm × 40 mm) were attached on the adaxial side (ADS) and abaxial side (ABS) of it. The application volume was 225 L/ha. Ponceau 4R, a dye usually used as a food coloring with no risk of environmental pollution and human and animal poisoning, was added as a tracer with a concentration of 5 g/L. During each test, the time when the MAS entered and left the test area was recorded to ensure that the deviation of the actual application volume from the set value did not exceed 5%. All tests were repeated 3 times (Table 1).
According to the canopy characteristics of pear and cherry, 10 parameters were settled within the adjustable range of the fan ( Table 2). OSC1-OSC6 were used on cherry, the fan speed was different between OSC1-OSC3, the installation height of the middle unit between OSC4 and OSC5 was different by 100 mm, and the vertical installation angle of the middle unit between OSC5 and OSC6 was different by 20 • .

Airflow Pattern Test
The airflow pattern test of MAS was conducted in an open field outdoors in a static way according to ISO 9898:2000 [34]. Figure 3 showed the test layout, a group of 3 Axis wind sensors [35] (WindMaster 1590-PK-020, Gill Instruments Ltd., Hampshire, UK) was installed from 0.6 m away from the ground to 3.2 m according to the vertical interval of 0.2 m. All parameters listed in Table 2 were tested at 0.5 m, 1.0 m, 1.5 m, and 2.0 m away from the MAS, respectively. Fans on both sides of the sprayer opened simultaneously to keep the working condition consistent with the orchard application. All sensors were connected to the computer for the signal transmission, and the output data is received by the software at a frequency of 10 Hz and further calculated in Cartesian coordinates (X, Y, Z), including the airflow velocity and direction on the YZ plane and the air velocity on the X-axis. For each measuring point and parameter, data were recorded at least 15 s.

Data Analyses
All samples were scanned with a scanner (DS-1610, Epson (China), Beijing) at 400 dpi to obtain images. An image processing program ImageJ [36] (National Institutes of Health,

Data Analyses
All samples were scanned with a scanner (DS-1610, Epson (China), Beijing) at 400 dpi to obtain images. An image processing program ImageJ [36] (National Institutes of Health, United States) was used for the analysis to get spray coverage [37]. CAD and CAB represent deposit coverage on ADS and ABS of the leaf (%), and the deposit coverage of whole leaf (CW, %) was calculated as follows: Where the ratio of deposit coverage on ABS and whole leaf (RBW) was calculated to account for droplet distribution uniformity on leaves: Where the ratio of deposit coverage on the center sample and the total sample in the same layer (RCT) was calculated to account for the penetration effect of droplets: where L, M, and R are sample sites in cherry canopy. As for pear, Left means L1 and L2, and R means R1 and R2 (Figure 2b). The 3D airflow velocity and direction corresponding to all sample points are obtained through interpolation for 2D gridded data in meshgrid format [38] by Matlab 2021a (Mathworks, Natick, MA, USA). The interpolated value at a sample point is based on a cubic interpolation of the values at neighboring grid points in each respective dimension. The interpolation is based on a cubic spline using not-a-knot end conditions and 6 indicators were obtained: X-axis, Y-axis, and Z-axis airflow velocities, ZY plane (0 • on Z-axis), ZX plane (0 • on Z-axis), and YX (0 For assessing the impact of these indicators on canopy deposition, the method combining partial least square (PLS) and the variable importance in projection (VIP) scores (also called the PLS-VIP method [39]) have been introduced to quantify the contribution.
All statistical analyses were performed using IBM SPSS Statistics (IBM Corp., Armonk, NY, USA). The mean values of CAD, CAB, CW, RBW, and RCT in different test parameters were compared by using one-way analysis of variance (ANOVA) via the Duncan test (α = 0.05). The bivariate correlation analysis was adopted to evaluate the correlation between airflow indicators and CAD, CAB, CW, and RBW of all test parameters by using Pearson test and two-tailed significance test. Table 3 shows mean values of all deposit indicators, including CAD, CAB, CW, RBW, and RCT, calculated from all samples in each layer of OSP1-OSP4 (results of all sample trees and replicates are involved). Intercomparison of OSP1-OSP3 was made on account of sharing the same installation height and tilt angle but different in fan speed. For the Top layer, the CAD and CW of OSP3 were significantly lower than those of OSP1 and had no significant difference with OSP2, and the CAB and RBW of OSP3 were significantly higher than those of OSP2 and had no significant difference with OSP1. For the Upper layer, the CAD of OSP3 was significantly lower than that of OSP1 and OSP2, the CAB of OSP3 was significantly higher than OSP1 and had no significant difference with OSP2, and the RBW of OSP3 was significantly higher than OSP1 and OSP2. The RCT of OSP1-OSP3 in all layers had no significant difference with each other. In the comparison between OSP2 and OSP4, the difference in deposition results was mainly due to the installation height and tilt angle of the Middle unit, the CAD and RCT of OSP4 in the Top layer were significantly lower than OSP2 but the CAB and RBW were higher. Meanwhile, in the Upper layer, the CAD of OSP4 was significantly lower than OSP2, and in the Lower layer the CAB of OSP4 was also lower than OSP2. The only difference between OSC1-OSC3 is the fan speed setting, which was similar to OSP1-OSP3. There was no significant difference for CAD and RCT in all layers of OSC1-OSC3 as shown in Table 4, however in the Middle layer, the CAB of OSC2 and OSC3 were significantly higher than OSC1. In the Bottom layer, OSC3 also showed a higher CAB than OSC1. There was no significant difference in the deposition effect between OSC3 and OSC6, nor between OSC4 and OSC5, however, the CAB of OSC5 in the Top layer was significantly higher than that of OSC6.

Comparison between Airflow Velocity Distribution and Deposit Coverage Distribution
The distribution of both airflow and spray canopy deposit varied according to the fan setting. For this reason, a comparison was made between them. As can be seen in Figure 4, the airflow velocities of OSP1-OSP3 decreased with distance at Top, Lower, and Bottom heights, while at Upper height the airflow showed the opposite trend. In the meantime, the CAB of OSP3 improved, but the CAD decreased in the Top and Upper layers. Compared to OSP2, the air velocity of OSP4 attenuated less at Top height but was lower at Lower height. As for the canopy deposit coverage, the CAB of OSP4 was higher in the Top but lower in the Lower layer, meanwhile the CAD was lower in both of the Top and Upper layers, which was consistent with the results shown in Section 3.1. OSC1-OSC3 shared a similar airflow velocity distribution pattern just like OSP1. OSP3, OSC2, and OSC3 have higher air velocities than OSC1 at Middle height, which made the CAB of OSC1 less than OSC2 and OSC3 at the same height. OSC3 has a higher airflow velocity at Middle height compared to OSC6, and OSC5 also has a higher airflow velocity at Top height compared to OSC4, however in the corresponding layers OSC6 has a similar CAB to OSC3 and OSC4 to OSC5. In addition, the OSC5 has a higher air velocity at Top height as well as a CAB compared to the OSC6 (see Figure 5). OSC1-OSC3 shared a similar airflow velocity distribution pattern just like OSP1. OSP3, OSC2, and OSC3 have higher air velocities than OSC1 at Middle height, which made the CAB of OSC1 less than OSC2 and OSC3 at the same height. OSC3 has a higher airflow velocity at Middle height compared to OSC6, and OSC5 also has a higher airflow velocity at Top height compared to OSC4, however in the corresponding layers OSC6 has a similar CAB to OSC3 and OSC4 to OSC5. In addition, the OSC5 has a higher air velocity at Top height as well as a CAB compared to the OSC6 (see Figure 5).

Results of OSP1-OSP4
For OSP1-OSP4, a PLS-VIP analysis was carried out between deposit indicators (CAD, CAB, CW, and RBW) and airflow indicators (X-v, Y-v, Z-v, ZY-d, ZX-d, YX-d). Results exhibited in Figure 6 showed that Z-v represented a more significant influence on CAB and RBW than the other indicators, while ZY-d made a greater contribution to CAD and CW. In addition, the effect of X-v on CAB and Z-v on CW cannot be ignored as well.

Results of OSP1-OSP4
For OSP1-OSP4, a PLS-VIP analysis was carried out between deposit indicators (CAD, CAB, CW, and RBW) and airflow indicators ( Results exhibited in Figure 6 showed that Z-v represented a more significant influence on CAB and RBW than the other indicators, while ZY-d made a greater contribution to CAD and CW. In addition, the effect of X-v on CAB and Z-v on CW cannot be ignored as well.

Results of OSP1-OSP4
For OSP1-OSP4, a PLS-VIP analysis was carried out between deposit indicators (CAD, CAB, CW, and RBW) and airflow indicators ( Results exhibited in Figure 6 showed that Z-v represented a more significant influence on CAB and RBW than the other indicators, while ZY-d made a greater contribution to CAD and CW. In addition, the effect of X-v on CAB and Z-v on CW cannot be ignored as well. According to Table 5, X-v and Z-v showed extremely significant positive correlations (p < 0.001) with CAB and RBW in the total and outside canopy, but also negative correlations (p < 0.05) with CAD in the outside canopy, while ZY-d showed significant negative correlations (p < 0.01) with both CAD and CW in the total and outside canopy. All these were largely consistent with the results represented in Figure 7. Table 5. Results of the correlation analysis between airflow and deposit indicators at different parts of pear canopy.

Deposit Indicators
Canopy Parts  As represented in Table 6, X-v had a relatively complex effect on canopy deposit coverage, showing positive correlations with CAB (p < 0.05) and RBW (p < 0.001) on the outside of the cherry canopy, but negative correlations with CAB and RBW (p < 0.05) on the inside of the canopy and CAD (p < 0.01) on the outside of the canopy. Y-v showed a negative correlation with CAD (p < 0.01) and CW (p < 0.05) inside the canopy, meanwhile YXd showed the same negative correlation with CAD and CW of the total canopy (p < 0.05), in addition, ZY-d showed a significant positive correlation with RBW inside the canopy (p < 0.001). Although a few of the airflow indicators in Table 6 showed different contributions to those in Figure 7, this does not prevent the overall results from being consistent. Table 6. Results of the correlation analysis between airflow and deposit indicators at different parts of cherry canopy.

Results of OSC1-OSC6
According to Figure 7, for the CAD and CW of cherry, the most influential indicator was YX-d, followed by Y-v, then X-v showed a significant influence on CAB. Moreover, the most influential indicator on RBW was ZY-d.
As represented in Table 6, X-v had a relatively complex effect on canopy deposit coverage, showing positive correlations with CAB (p < 0.05) and RBW (p < 0.001) on the outside of the cherry canopy, but negative correlations with CAB and RBW (p < 0.05) on the inside of the canopy and CAD (p < 0.01) on the outside of the canopy. Y-v showed a negative correlation with CAD (p < 0.01) and CW (p < 0.05) inside the canopy, meanwhile YX-d showed the same negative correlation with CAD and CW of the total canopy (p < 0.05), in addition, ZY-d showed a significant positive correlation with RBW inside the canopy (p < 0.001). Although a few of the airflow indicators in Table 6 showed different contributions to those in Figure 7, this does not prevent the overall results from being consistent. Table 6. Results of the correlation analysis between airflow and deposit indicators at different parts of cherry canopy.

Deposit Indicators
Canopy Parts

Discussion
In most cases, the air adjustments of AAS and ATS are based on the rotational speed of the fan and on the position of air deflectors [41] which impact air velocity and air direction. For this reason, there are limited options for adjusting the airflow pattern and vertical spray distribution. In this research the MAS allowed for more adjustments by changing the installation height, tilt angle, and fan speed, which offered a multivariate scenario in this study. As mentioned before, in the absence of a tree canopy, the spray volume distribution was directly influenced by the airflow pattern [4]. However, in the case of pesticide applications, the effects of airflow velocity and direction (mainly determined by fan parameters) on canopy deposition were relatively complex. By the influence of airflow, droplets are forced into the canopy and attached to the leaves. In the meantime, leaves are swung and lifted, which can somehow increase the deposition on the leaves, especially on the ABS.
For the spray test conducted on pear in this study, the distance between spray units and the trunk was 2.25 m, which means the airflow between 1.5 m and 2 m from the fan entered the canopy and had a significant impact on droplet deposition, therefore the velocity of airflow inside the canopy (AI) was used as the main reference for evaluating pear canopy deposition. Compared to the airflow distribution patterns of OSP1, the AI velocity of OSP3 was higher at Upper and lower at Top (Figure 4), which makes the leaves in both the two layers more susceptible to be uplifted. Due to this, the exposed area of the ABS was increased, resulting in a higher CAB for OSP3 (11.00%) than OSP1 (6.26%) at Upper. On the other hand, considering that the distance between units and the cherry trunk is 1.25 m, the airflow between 1.0 m and 1.5 m from the fan should be defined as AI for the evaluation of the spray effect. For OSC1-OSC3 ( Figure 5), the AI velocities of OSC2 and OSC3 were higher than OSC1 at Middle height, which made the twisting frequency of leaves and the exposure probability of the ABS increase, and thus both OSC2 (4.81%) and OSC3 (9.04%) had greater CAB than OSC1 (1.36) in the Middle layer.
Compared to OSC6, OSC3 had greater AI velocity at Middle height, however there was no significant difference in CAD and CAB at Middle layer between them, which did not seem to be consistent with the previous analysis. On the other hand, OSC6 got higher AI velocity at Bottom than OSC3, so it was presumed that under the combined effect of airflow at both Middle and Bottom, the twisting frequencies of their Middle layer leaves were close. A similar situation occurred between OSC4 and OSC5, where OSC5 got a higher AI velocity at Top height but a lower AI velocity at Middle height compared to OSC4, from this point the CAD and CAB of OSC5 in the Top layer were also not significantly different from OSC4.
In general, the enhanced velocity of airflow inside the canopy resulted in an increase of deposition coverage on the ABS of leaves, for both pear and cherry, however it did not provide a significant improvement to the spray penetration. The difference is that the smaller pear leaves, compared to the cherry leaves, oscillated mainly in the longitudinal direction by airflow, which made that an increased exposed area of the ABS which was always accompanied by a decrease exposure of the ADS. For this reason, the increase of CAB happened frequently in conjunction with the decrease of CAD. The cherry leaves were slender and mainly twisted in the axial direction, which lead to an increase of CAB without decreasing the CAD. Furthermore, in many cases the spray coverage in a particular layer (e.g., Top layer of OSP3, Middle layer of OSC3, Top layer of OSC5) was simultaneously influenced by the effect of both the airflow in this height and that above or below it, which can be referred to as a regional airflow contribution, but the rationale for this phenomenon is unclear and needs to be explored in further studies.
Over the years, many reports have focused on spray penetration [25,42], distribution [43,44], and the mass balance [8,45] in orchards, which helps to clarify the practical application effects of different spray technologies and fan operating parameters. However, from the point of disease and pest control, the deposit on the ADS and ABS of leaves should also be taken into account.
The results of the PLS-VIP and correlation analysis showed that the enhanced X-v and Z-v improved (p < 0.001) the CAB on the outside of pear canopy, but for cherry, none of the airflow indicators had a significant impact on the CAB. On the other hand, for the increased ZY-d (p < 0.01) for pear as well as the increased X-v and Y-v (p < 0.01) for cherry, both showed negative effects on the CAD. Obviously, pear and cherry are very different in canopy structure and leaf shape. By the influence of airflow, the pear leaves swung violently and the exposure of the ABS increased, which resulted in the improvement of the CAB. However, for the cherry leaves, the changes in airflow did not significantly increase the exposure of the ABS. Moreover, it is worth noting that the reduction of CAD is very detrimental to the efficacy of pesticide control and should be avoided in the application. For pear and cherry orchards, we should adopt different airflow patterns to improve the spraying effect. Based on the structure of the MAS, the adjustment of X-v can be achieved by changing the angle between the unit and the travel direction, Z-v is mainly dependent on the fan speed setting, while the ZY-d can be adjusted by changing the tilt angle.
In recent years, efforts have focused on improving the design of pesticide application equipment. Grella et al. [46] tested the effect of different fan settings, air-conveyor orientation, and nozzle configuration on both airflow pattern and vertical spray distribution, and the results showed that a forward air-conveyor orientation was selected as one of the most optimal settings for spray applications in a trellised vineyard. Interestingly, in this study a similar trend was observed (the enhanced X-v could be adjusted by changing the install angle between the unit and the travel direction) that improved the deposit coverage in the ABS. Therefore, to some extent we can conclude that the forward airflow has a positive contribution to the spray effect.
In the last decade, agricultural unmanned aerial vehicle (UAV) has become a widely used piece of equipment for orchard pesticide application, especially in East Asian countries [47]. The downwash airflow of the UAV plays an important role in the transportation of droplets to the target [48,49], which was similar to the horizontal and/or vertical airflow from air-assisted sprayers. However, the UAV had a much lower deposition on leaves compared to the AAS [28,50,51]. Zhang et al. [52] pointed out that, in order to improve the spraying efficacy of UAV sprayers and reduce off-target losses, it is essential to understand the distribution characteristics of downwash airflow inside and around the target tree canopy. From this point of view, we suggest that the velocity and directional distribution characteristics of the downwash airflow should be focused on, which is a key factor affecting the droplets deposit distribution in the canopy, as reported in the present study.
Clearly, the airflow velocity and direction had a significant effect on spray deposit, and the fundamental cause of this is that the behaviors of droplets [53] and leaves [54] are influenced by airflow, which will be the focus of our future research. Although there is a correlation between the spray indicators, considering that this study aims to make a preliminary exploration of the effects of airflow indicators on deposition indicators, a large number of field tests for different fan parameters are still needed before we can build a predictive model.

Conclusions
Spray tests and airflow distribution tests were conducted with ten different fan settings using a multi-unit air-assisted sprayer. The effects of various airflow distribution patterns on spray deposition coverage and penetration were compared, and the correlation between airflow indicators and deposition indicators was evaluated. The results showed that the increased AI improved the CAB of pear (from 3.33% to 11.80% in the Top canopy and from 6.26% to 11.00% in the Upper canopy) and cherry leaves (from 3.61% to 10.87% in the Top canopy, from 1.36% to 9.04% in the Middle canopy, and from 3.40% to 9.04% in the Bottom canopy) but had no significant effect on spray penetration. As a whole, spray deposition in one part of the canopy was influenced by the combined effects of airflow in a wider area. The enhanced X-v and Z-v improved the CAB on the outside of pear canopy (p < 0.001), but for cherry, none of the airflow indicators had a significant impact on the CAB independently. On the other hand, the increased ZY-d for pear as well as the increased X-v and Y-v for cherry both showed negative effects on the CAD (p < 0.01).
According to our findings, for fruits with small leaves, such as pears, apples, citrus, etc., it is recommended to increase the airflow velocity in the horizontal and forward direction to optimize the spraying effect. As for cherry and other fruits with larger leaves, such as mangoes, lychees, etc., an increase in the upward airflow and an appropriate reduction of airflow velocity are suggested. For years, we have been committed to the improvement of spray performance on the abaxial side of leaves in orchards by setting optimal application parameters and improving the spray system. More research is still needed to clarify the multiple correlations between airflow velocity/direction and spray deposit distribution. Furthermore, the dynamical behavior of droplets and leaves in the airflow, as a fundamental principle of droplet deposition in the canopy, will be further investigated to improve our understanding of air-assisted spraying.

Data Availability Statement:
The data presented in this study are available on request from the corresponding author.