Multiresponsive Behavior of Functional Poly(p-phenylene vinylene)s in Water

The multiresponsive behavior of functionalized water-soluble conjugated polymers (CPs) is presented with potential applications for sensors. In this study, we investigated the aqueous solubility behavior of water-soluble CPs with high photoluminescence and with a particular focus on their pH and temperature responsiveness. For this purpose, two poly(phenylene vinylene)s (PPVs)—namely 2,5-substituted PPVs bearing both carboxylic acid and methoxyoligoethylene glycol units—were investigated, with different amount of carboxylic acid units. Changes in the pH and temperature of polymer solutions led to a response in the fluorescence intensity in a pH range from 3 to 10 and for temperatures ranging from 10 to 85 °C. Additionally, it is demonstrated that the polymer with the largest number of carboxylic acid groups displays upper critical solution temperature (UCST)-like thermoresponsive behavior in the presence of a divalent ion like Ca2+. The sensing capability of these water-soluble PPVs could be utilized to design smart materials with multiresponsive behavior in biomedicine and soft materials.


Introduction
Polymers that respond to external stimuli such as pH, temperature, ionic strength, light, and concentration are extensively studied for a broad range of applications, including biomedical applications like drug delivery [1,2], cell imaging [3][4][5], as well as biological [6] and optical sensing [7][8][9]. Polymer-based systems with responsive properties can straightforwardly be designed thanks to recent advances in polymer synthesis as well as better understanding of physicochemical properties at the molecular level [10][11][12]. Such responsive functions arise from the chemical or topological structure of the polymer and lead to the design of stimuli-responsive smart materials with tailored functions. In contrast to their small molecular analogs, macromolecular or polymeric sensors exhibit numerous advantageous features, such as adjustable water solubility, higher detection sensitivity, straightforward integration into sensing devices, better stability, biocompatibility, and sharpened responses [13]. Scheme 1. General polymer structure with stimuli-responsive functional units, its response to pH, temperature, and upper critical solution temperature (UCST)-like behavior when complexed with Ca 2+ .

Materials
All chemicals were commercially available and used as received unless otherwise stated. Milli-Q water was obtained from a Sartorius Arium 611(Brussels, Belgium) with a Sartopore 2 150 (0.45 + 0.2 mm pore size) cartridge filter (resistivity less than 18.2 MU cm). NaOH and HCl are from Acros Organics (Geel, Belgium) and were diluted with Milli-Q water. Functionalized PPVs were synthesized as previously reported by us [13].

Instrumentation/Methods
The pH was recorded with a Mettler Toledo FE20 FiveEasy Benchtop pH meter (Brussels Belgium). All spectroscopic measurements were carried out in 1 cm quartz cuvettes. The fluorescence emission spectra were measured on a Cary Eclipse fluorescence spectrometer (Santa Clara, CA, USA) with Peltier temperature control under stirring. The excitation wavelength was set at 392 nm with photomultiplier tube voltage at 600 V. The split width of the excitation and emission were both 5 nm. The fluorescence spectra were recorded with a recording emission range of 400-750 nm. The thermal measurements were taken between 5 and 85 °C with heating/cooling rate of 1 °C/min. Optical absorption (UV-vis) spectra were measured using a Varian Cary 300 Bio UV-visible spectrometer (Santa Clara, CA, USA) equipped with a Cary Peltier temperature control while stirring. Samples were measured in quartz cuvettes with a pathlength of 1.0 cm in the wavelength range of 200-600 nm. The concentration of each sample was 1.0 mg/mL in Milli-Q water. 1 H-NMR spectra were recorded on a Bruker Avance 400 or 300 MHz spectrometer (Billerica, MA, USA) at room temperature in deuterated solvents. Chemical shifts (δ) are given in ppm relative to TMS.
Size-exclusion chromatography (SEC) was performed on an Agilent 1260-series HPLC system (Santa Clara, CA, USA) equipped with a 1260 online degasser, a 1260 ISO-pump, a 1260 automatic liquid sampler, a thermostatted column compartment, a 1260 diode array detector (DAD) and a 1260 refractive index detector (RID). Analyses were performed on a PSS Gram30 column in series with a PSS Gram1000 column at 50 °C. DMAc containing 50 mM of LiCl was used as eluent at a flow rate of 0.6 mL/min. The SEC traces were analyzed using the Agilent Chemstation software with the GPC add-on. Size exclusion chromatography was used to evaluate the number average molecular weight (Mn) and dispersity (Ð) against PMMA standards.
Turbidity measurements were performed on a Crystal16 from Technobis Crystallization Systems (Alkmaar, The Netherlands) at a wavelength of 600 nm. The samples were fully dissolved at pH = 10 (0.5 mg/mL), after which the samples were placed in the instrument and cooled to 10 °C. The transmittance was measured during at least two controlled cooling/heating cycles with a cooling/heating rate of 1 °C·min −1 while stirring in PS cuvettes controlled by block temperature probe. Scheme 1. General polymer structure with stimuli-responsive functional units, its response to pH, temperature, and upper critical solution temperature (UCST)-like behavior when complexed with Ca 2+ .

Materials
All chemicals were commercially available and used as received unless otherwise stated. Milli-Q water was obtained from a Sartorius Arium 611(Brussels, Belgium) with a Sartopore 2 150 (0.45 + 0.2 mm pore size) cartridge filter (resistivity less than 18.2 MU cm). NaOH and HCl are from Acros Organics (Geel, Belgium) and were diluted with Milli-Q water. Functionalized PPVs were synthesized as previously reported by us [13].

Instrumentation/Methods
The pH was recorded with a Mettler Toledo FE20 FiveEasy Benchtop pH meter (Brussels, Belgium). All spectroscopic measurements were carried out in 1 cm quartz cuvettes. The fluorescence emission spectra were measured on a Cary Eclipse fluorescence spectrometer (Santa Clara, CA, USA) with Peltier temperature control under stirring. The excitation wavelength was set at 392 nm with photomultiplier tube voltage at 600 V. The split width of the excitation and emission were both 5 nm. The fluorescence spectra were recorded with a recording emission range of 400-750 nm. The thermal measurements were taken between 5 and 85 • C with heating/cooling rate of 1 • C/min. Optical absorption (UV-vis) spectra were measured using a Varian Cary 300 Bio UV-visible spectrometer (Santa Clara, CA, USA) equipped with a Cary Peltier temperature control while stirring. Samples were measured in quartz cuvettes with a pathlength of 1.0 cm in the wavelength range of 200-600 nm. The concentration of each sample was 1.0 mg/mL in Milli-Q water. 1 H-NMR spectra were recorded on a Bruker Avance 400 or 300 MHz spectrometer (Billerica, MA, USA) at room temperature in deuterated solvents. Chemical shifts (δ) are given in ppm relative to TMS. Size-exclusion chromatography (SEC) was performed on an Agilent 1260-series HPLC system (Santa Clara, CA, USA) equipped with a 1260 online degasser, a 1260 ISO-pump, a 1260 automatic liquid sampler, a thermostatted column compartment, a 1260 diode array detector (DAD) and a 1260 refractive index detector (RID). Analyses were performed on a PSS Gram30 column in series with a PSS Gram1000 column at 50 • C. DMAc containing 50 mM of LiCl was used as eluent at a flow rate of 0.6 mL/min. The SEC traces were analyzed using the Agilent Chemstation software with the GPC add-on. Size exclusion chromatography was used to evaluate the number average molecular weight (M n ) and dispersity (Ð) against PMMA standards.

Sample Preparation
Samples for fluorescent measurements first were dissolved in Milli-Q water at pH = 13 and adjusted to lower pH values by dilute HCl. All samples were prepared at 0.01 mg/mL. For UV-vis measurements, samples were prepared at pH = 10 (0.5 mg/mL) in Milli-Q water (Milli-Q, resistivity ≤18.2 MΩ·cm).

Sample Preparation
Samples for fluorescent measurements first were dissolved in Milli-Q water at pH = 13 and adjusted to lower pH values by dilute HCl. All samples were prepared at 0.01 mg/mL. For UV-vis measurements, samples were prepared at pH = 10 (0.5 mg/mL) in Milli-Q water (Milli-Q, resistivity ≤18.2 MΩ·cm).

Synthesis and Characterization
PPVs with functional carboxylic acid and oligoethylene glycol units were previously reported to show high solubility and high luminescence in aqueous and organic media [13]. Here, specifically 2,5-substituted PPV polymers decorated with methoxytriethylene glycol units and carboxylic acid groups (denoted as PDTriG) and its more hydrophobic copolymer with methoxytrietylene glycol and methoxy side groups (denoted as PMEE-PDTriG) were investigated to evaluate their responsive behavior ( Figure 2). PDTriG was synthesized as previously reported [13] whereas the monomer and polymer of PMEE-PDTriG were synthesized using a slightly modified literature procedure [13]. These polymers were characterized by means of NMR and SEC. Size exclusion chromatography (SEC) with DMA as a solvent and PMMA as calibration standard was used to obtain the average molecular mass of PDTriG (M n = 197,000; Ð= 1.34) and PMEE-PDTriG (M n = 108,200; Ð = 1.04). PPVs with functional carboxylic acid and oligoethylene glycol units were previously reported to show high solubility and high luminescence in aqueous and organic media [13]. Here, specifically 2,5-substituted PPV polymers decorated with methoxytriethylene glycol units and carboxylic acid groups (denoted as PDTriG) and its more hydrophobic copolymer with methoxytrietylene glycol and methoxy side groups (denoted as PMEE-PDTriG) were investigated to evaluate their responsive behavior ( Figure 2). PDTriG was synthesized as previously reported [13] whereas the monomer and polymer of PMEE-PDTriG were synthesized using a slightly modified literature procedure [13]. These polymers were characterized by means of NMR and SEC. Size exclusion chromatography (SEC) with DMA as a solvent and PMMA as calibration standard was used to obtain the average molecular mass of PDTriG (Mn = 197,000; Ð= 1.34) and PMEE-PDTriG (Mn = 108,200; Ð = 1.04).

pH-Responsive Behavior
It is well known that the optical properties of CPs are governed by the polarity of the polymer, conformational changes in the backbone, the polarity of the solvent, intramolecular dynamics, and interchain interactions [55,56]. A change in the conformation of the polymer chain is dictated by different variables, among which solvent and temperature are prominent. Accordingly, any external factor effecting backbone configuration influences the photophysical features of CPs. It was shown previously that the emission spectra of functional PPVs were highly dependent on acidity of the media [13]. Photophysical properties of both PDTriG and PMEE-PDTriG were studied in aqueous media as function of pH by fluorescence spectroscopy. It was observed that the polymers did not readily dissolve in water and in buffer solution, unless the pH was increased to 13. Therefore, the samples were first fully solubilized at pH = 13 followed by addition of dilute hydrochloric acid solution to adjust the pH to the desired pH values. When following this procedure the polymers remained in aqueous solution and no macroscopic precipitate was observed. As shown in the fluorescence spectra in Figure 3a, PDTriG has a maximum emission at 498 nm and an excitation maximum at 392 nm, as measured at pH = 13, 0.01 mg/mL. PMEE-PDTriG was found to have an emission λmax of 478 nm and an excitation λmax of 378 nm when measured at the same concentration and pH (Figure 3b) indicating both polymers have similar optical properties. Thus, all the emission measurements were carried out at an excitation maximum wavelength λmax = 392 nm for PDTriG and λmax = 378 nm for PMEE-PDTriG. The fluorescence intensity of both polymers was found to be dependent on the pH of the solution, as expected based on the presence of the carboxylic acid groups. While at pH below 7 quenching of the fluorescence was observed, strong emission was found at higher pH (pH > 7). This change in emission intensity can be attributed to the enhanced solubility of the polymer at higher pH values due to deprotonation of the carboxylic acid groups, thereby suppressing aggregation of the polymer and quenching of fluorescence [57]. Fluorescence intensity increased for both of the polymers as pH values increased, without shifting of emission maxima peaks (Figure 3c,d). A slight blue shift is observed for PDTriG with decreasing acidity, at pH 6 and below, due to aggregation of amphiphilic CPs as they become protonated [56]. It was, however, observed that the fluorescence intensity of PDTriG decreased in time at pH 13 and at pH 6 and lower.

pH-Responsive Behavior
It is well known that the optical properties of CPs are governed by the polarity of the polymer, conformational changes in the backbone, the polarity of the solvent, intramolecular dynamics, and interchain interactions [55,56]. A change in the conformation of the polymer chain is dictated by different variables, among which solvent and temperature are prominent. Accordingly, any external factor effecting backbone configuration influences the photophysical features of CPs. It was shown previously that the emission spectra of functional PPVs were highly dependent on acidity of the media [13]. Photophysical properties of both PDTriG and PMEE-PDTriG were studied in aqueous media as function of pH by fluorescence spectroscopy. It was observed that the polymers did not readily dissolve in water and in buffer solution, unless the pH was increased to 13. Therefore, the samples were first fully solubilized at pH = 13 followed by addition of dilute hydrochloric acid solution to adjust the pH to the desired pH values. When following this procedure the polymers remained in aqueous solution and no macroscopic precipitate was observed. As shown in the fluorescence spectra in Figure 3a, PDTriG has a maximum emission at 498 nm and an excitation maximum at 392 nm, as measured at pH = 13, 0.01 mg/mL. PMEE-PDTriG was found to have an emission λ max of 478 nm and an excitation λ max of 378 nm when measured at the same concentration and pH (Figure 3b) indicating both polymers have similar optical properties. Thus, all the emission measurements were carried out at an excitation maximum wavelength λ max = 392 nm for PDTriG and λ max = 378 nm for PMEE-PDTriG. The fluorescence intensity of both polymers was found to be dependent on the pH of the solution, as expected based on the presence of the carboxylic acid groups. While at pH below 7 quenching of the fluorescence was observed, strong emission was found at higher pH (pH > 7). This change in emission intensity can be attributed to the enhanced solubility of the polymer at higher pH values due to deprotonation of the carboxylic acid groups, thereby suppressing aggregation of the polymer and quenching of fluorescence [57]. Fluorescence intensity increased for both of the polymers as pH values increased, without shifting of emission maxima peaks (Figure 3c,d). A slight blue shift is observed for PDTriG with decreasing acidity, at pH 6 and below, due to aggregation of amphiphilic CPs as they become protonated [56]. It was, however, observed that the fluorescence intensity of PDTriG decreased in time at pH 13 and at pH 6 and lower. In contrast, PMEE-PDTriG was found to be more stable and only showed a decrease in fluorescence intensity at pH 13 and below pH 3. At lower pH values, protonation of the carboxylic acid groups is presumed to cause insolubility of the polymers; this was proved by complete loss of emission intensity, which was not restored even after adjusting pH value back to 10. Especially, the higher stability at lower pH values for PMEE-PDTriG indicates that the presence of protonated carboxylic acid groups induces degradation and/or insolubility, which is more pronounced for PDTriG as it has more carboxylic acid groups. Note that for sample preparation, the polymers were only dissolved in pH 13 for a short time to avoid degradation of the materials, presumably resulting from the high concentration of hydroxyl anions facilitating degradation of the polymer backbone. In contrast, PMEE-PDTriG was found to be more stable and only showed a decrease in fluorescence intensity at pH 13 and below pH 3. At lower pH values, protonation of the carboxylic acid groups is presumed to cause insolubility of the polymers; this was proved by complete loss of emission intensity, which was not restored even after adjusting pH value back to 10. Especially, the higher stability at lower pH values for PMEE-PDTriG indicates that the presence of protonated carboxylic acid groups induces degradation and/or insolubility, which is more pronounced for PDTriG as it has more carboxylic acid groups. Note that for sample preparation, the polymers were only dissolved in pH 13 for a short time to avoid degradation of the materials, presumably resulting from the high concentration of hydroxyl anions facilitating degradation of the polymer backbone. When plotting the fluorescence intensity of PDTriG versus pH, it is clear that no good correlation can be drawn, possibly due to the low stability of the polymers. However, PMEE-PDTriG revealed a linear decrease of fluorescence intensity with decreasing pH in between pH 3 and pH 10, making it suitable as fluorescent pH sensor. This rather broad pH range also facilitates employment in a biological environment as it covers the physiological pH range. When plotting the fluorescence intensity of PDTriG versus pH, it is clear that no good correlation can be drawn, possibly due to the low stability of the polymers. However, PMEE-PDTriG revealed a linear decrease of fluorescence intensity with decreasing pH in between pH 3 and pH 10, making it suitable as fluorescent pH sensor. This rather broad pH range also facilitates employment in a biological environment as it covers the physiological pH range.

Thermoresponsive Behavior
As mentioned above, the conformation of the π-conjugated backbone has substantial impact on the photophysical properties of CPs [8]. Therefore, thermoresponsive behavior of the studied PPVs would also induce a change in solubility that also strongly influences the backbone conformation, directly leading to fluorescent output signal. Possible temperature effects on the photoluminescent properties of the more stable PMEE-PDTriG were studied by investigating the fluorescence intensity as function of temperatures, where it was anticipated that these polymers may exhibit LCST behavior based on the methoxyoligoethylene glycol side chains. Fluorescence intensity of the PMEE-PDTriG was measured at different pH values upon heating from 20 to 80 • C, revealing a minor decrease in fluorescence intensity with increasing temperature due to increased chain mobility leading to a decrease in conjugation length ( Figure 4). The relative order in fluorescence intensity at different pH values is, however, retained at different temperatures. Nonetheless, this minor temperature influence will make it necessary to recalibrate the pH-sensing response at different temperatures.  To gain further insights into the effect of temperature and, especially, dehydration of the oligoethylene glycol side chains on the polymer chain conformation, full emission spectra were recorded at different temperatures ( Figure 5). Changing the temperature, however, showed no shift in emission wavelength maxima but only resulted in a decrease in fluorescence intensity. The low emission intensity at lower temperatures showed a pronounced increase at 9 °C, giving a jump of emission intensity as depicted in Figure 5b. Therefore, it may be speculated that the collapse of the oligoethylene glycol side chains leads to an increase in chain rigidity, thereby increasing the conjugation length that results in enhanced emission intensity. It is noteworthy to mention that the more hydrophilic PDTriG did not show such thermoresponsive behavior.
The observed thermoresponsive emission behavior of PMEE-PDTriG may be utilized for aqueous temperature sensing, whereby the hysteresis gap could lead to a thermal memory of the solution temperature [58,59].  A more critical look at Figure 4 reveals some minor disturbances in fluorescence intensity at lower temperature, especially at pH 7. Intrigued by this effect and to probe the stability of the polymer, the fluorescence intensity was recorded during multiple heating-cooling cycles at pH 7, 10, and 13 in between 10 and 80 • C (Figure 4b-d). First of all, these experiments revealed that PMEE-PDTriG is stable during multiple cycles; only the first heating shows a slightly different behavior at pH 7 and 10, most likely related to solubilization since this effect is no longer seen in the second and third heating runs. Secondly, it is evident that PMEE-PDTriG reveals distinct thermoresponsive behavior around 10-20 • C. This abrupt increase in fluorescence emission intensity upon heating is most likely due to LCST-like behavior of the oligoethylene glycol side chains, as such LCST behavior is an abrupt cooperative dehydration effect. More specifically, the observed increase in fluorescence emission intensity may be attributed to (partial) dehydration of the oligoethylene glycol side chains, leading them to collapse. No macroscopic phase separation is observed, as the PMEE-PDTriG remains stabilized and solubilized by the charged carboxylate groups. Interestingly, the reverse process of rehydration of the oligoethylene glycol side chains only occurs around 10 • C, representing some hysteresis in the responsive behavior. This observation may be related to the presence of the hydrophobic alkyl chains on the carboxylic acid side chains facilitating the formation of hydrophobic domains with the dehydrated oligoethylene glycol chains, thereby making it more difficult to rehydrate these oligoethylene glycol chains during cooling.
To gain further insights into the effect of temperature and, especially, dehydration of the oligoethylene glycol side chains on the polymer chain conformation, full emission spectra were recorded at different temperatures ( Figure 5). Changing the temperature, however, showed no shift in emission wavelength maxima but only resulted in a decrease in fluorescence intensity. The low emission intensity at lower temperatures showed a pronounced increase at 9 • C, giving a jump of emission intensity as depicted in Figure 5b. Therefore, it may be speculated that the collapse of the oligoethylene glycol side chains leads to an increase in chain rigidity, thereby increasing the conjugation length that results in enhanced emission intensity. It is noteworthy to mention that the more hydrophilic PDTriG did not show such thermoresponsive behavior. To gain further insights into the effect of temperature and, especially, dehydration of the oligoethylene glycol side chains on the polymer chain conformation, full emission spectra were recorded at different temperatures ( Figure 5). Changing the temperature, however, showed no shift in emission wavelength maxima but only resulted in a decrease in fluorescence intensity. The low emission intensity at lower temperatures showed a pronounced increase at 9 °C, giving a jump of emission intensity as depicted in Figure 5b. Therefore, it may be speculated that the collapse of the oligoethylene glycol side chains leads to an increase in chain rigidity, thereby increasing the conjugation length that results in enhanced emission intensity. It is noteworthy to mention that the more hydrophilic PDTriG did not show such thermoresponsive behavior.
The observed thermoresponsive emission behavior of PMEE-PDTriG may be utilized for aqueous temperature sensing, whereby the hysteresis gap could lead to a thermal memory of the solution temperature [58,59].  The observed thermoresponsive emission behavior of PMEE-PDTriG may be utilized for aqueous temperature sensing, whereby the hysteresis gap could lead to a thermal memory of the solution temperature [58,59].

UCST-Like Behavior with Calcium(II) Ions
Besides studying the potential of these functional PPVs as pH and temperature sensors, we were interested to exploit the presence of carboxylate groups for inducing UCST-like thermoresponsive solubility behavior. Therefore, PDTriG was employed as it has a higher load of carboxylic acid groups. The polymer was solubilized in basic solution so that the carboxylic acid groups were present as carboxylate groups, which are known to bind with calcium(II) ions in a 2:1 fashion [60][61][62]. Upon addition of half an equivalent of calcium(II) ions compared to the carboxylate groups, all polymer precipitated out of solution, ascribed to interpolymer crosslinking by calcium(II)-carboxylate coordination as schematically depicted in Scheme 2. By heating up the polymer-calcium(II) precipitate, the supramolecular association is weakened leading to dissolution of the polymer and the calcium(II) ions, thereby providing reversible binding of calcium(II) as function of temperature. solubility behavior. Therefore, PDTriG was employed as it has a higher load of carboxylic acid groups. The polymer was solubilized in basic solution so that the carboxylic acid groups were present as carboxylate groups, which are known to bind with calcium(II) ions in a 2:1 fashion [60][61][62]. Upon addition of half an equivalent of calcium(II) ions compared to the carboxylate groups, all polymer precipitated out of solution, ascribed to interpolymer crosslinking by calcium(II)-carboxylate coordination as schematically depicted in Scheme 2. By heating up the polymer-calcium(II) precipitate, the supramolecular association is weakened leading to dissolution of the polymer and the calcium(II) ions, thereby providing reversible binding of calcium(II) as function of temperature. Scheme 2. Schematic representation of the reversible binding of PDTriG with CaCl2 in basic media leading to UCST behavior.
The complexation and precipitation of the polymer with calcium(II) ions is also shown in Figure  6, indicated by the loss of UV-absorbance as well as by the photographs of the vial. As the precipitated PDTriG-calcium complex is held together by noncovalent supramolecular interactions, we explored whether heating would lead to sufficient lowering of the interaction strength to bring the polymer back in solution. Indeed, heating the sample vial led to regaining of the yellow solution as the precipitate redissolved. Subsequent cooling led to precipitation demonstrating the reversibility of this UCST-like thermoresponsive behavior of PDTriG. Temperature response of the PDTriG and PDTriG-calcium complex is further shown by UV-vis turbidimetry. As depicted in Figure 7, heating the samples from 10 to 70 °C gives no change in the transmittance of the polymer solution, whereas the polymer-calcium complex goes through UCST-like phase transition. The complexation and precipitation of the polymer with calcium(II) ions is also shown in Figure 6, indicated by the loss of UV-absorbance as well as by the photographs of the vial. As the precipitated PDTriG-calcium complex is held together by noncovalent supramolecular interactions, we explored whether heating would lead to sufficient lowering of the interaction strength to bring the polymer back in solution. Indeed, heating the sample vial led to regaining of the yellow solution as the precipitate redissolved. Subsequent cooling led to precipitation demonstrating the reversibility of this UCST-like thermoresponsive behavior of PDTriG. Temperature response of the PDTriG and PDTriG-calcium complex is further shown by UV-vis turbidimetry. As depicted in Figure 7, heating the samples from 10 to 70 • C gives no change in the transmittance of the polymer solution, whereas the polymer-calcium complex goes through UCST-like phase transition.

UCST-Like Behavior with Calcium(II) Ions
Besides studying the potential of these functional PPVs as pH and temperature sensors, we were interested to exploit the presence of carboxylate groups for inducing UCST-like thermoresponsive solubility behavior. Therefore, PDTriG was employed as it has a higher load of carboxylic acid groups. The polymer was solubilized in basic solution so that the carboxylic acid groups were present as carboxylate groups, which are known to bind with calcium(II) ions in a 2:1 fashion [60][61][62]. Upon addition of half an equivalent of calcium(II) ions compared to the carboxylate groups, all polymer precipitated out of solution, ascribed to interpolymer crosslinking by calcium(II)-carboxylate coordination as schematically depicted in Scheme 2. By heating up the polymer-calcium(II) precipitate, the supramolecular association is weakened leading to dissolution of the polymer and the calcium(II) ions, thereby providing reversible binding of calcium(II) as function of temperature. Scheme 2. Schematic representation of the reversible binding of PDTriG with CaCl2 in basic media leading to UCST behavior.
The complexation and precipitation of the polymer with calcium(II) ions is also shown in Figure  6, indicated by the loss of UV-absorbance as well as by the photographs of the vial. As the precipitated PDTriG-calcium complex is held together by noncovalent supramolecular interactions, we explored whether heating would lead to sufficient lowering of the interaction strength to bring the polymer back in solution. Indeed, heating the sample vial led to regaining of the yellow solution as the precipitate redissolved. Subsequent cooling led to precipitation demonstrating the reversibility of this UCST-like thermoresponsive behavior of PDTriG. Temperature response of the PDTriG and PDTriG-calcium complex is further shown by UV-vis turbidimetry. As depicted in Figure 7, heating the samples from 10 to 70 °C gives no change in the transmittance of the polymer solution, whereas the polymer-calcium complex goes through UCST-like phase transition.

Conclusions
Functional groups on PPV not only give high solubility in water but also provide new properties for sensing regime of the polymers. In this study, water-soluble PPVs with carboxylic acid groups and methoxyoligoethylene units as pendant side chains are reported to have high luminescence in aqueous media with multiresponsive behavior. Higher solubility is attained for the polymers with

Conclusions
Functional groups on PPV not only give high solubility in water but also provide new properties for sensing regime of the polymers. In this study, water-soluble PPVs with carboxylic acid groups and methoxyoligoethylene units as pendant side chains are reported to have high luminescence in aqueous media with multiresponsive behavior. Higher solubility is attained for the polymers with increased pH values as more carboxylic acid groups are deprotonated, thereby inhibiting aggregation of the polymers and enhancing fluorescence intensity. This phenomenon is observed for both of the polymers, providing pH response behavior of PDTriG in between pH 6-13 and in between pH 3-13 for PMEE-PDTriG. Higher solubility of the reported polymers was also achieved by influence of temperature, making them polymeric-thermometers as they are thermosensitive in aqueous media. Photophysical properties at different pH values in a broad temperature window (10-80 • C) shows that there is a temperature response for both polymers. Moreover, stability of the polymers was maintained throughout multiple heating-cooling cycles. Furthermore, UCST-like thermoresponsive behavior was demonstrated for PDTriG with Ca 2+ ions, which are known to bind divalently with carboxylate groups. The combined pH-responsive and thermoresponsive properties of these PPVs are promising features for the design of sensors, specifically for their use as dual sensors for temperature and pH values. Such dual sensors are a highly desired addition to the class of polymeric sensors and a related system based on a temperature-responsive polymer with a pH-responsive solvatochromic dye in the side chain. The hysteresis gap in the heating-cooling cycles at lower temperatures for PMEE-PDTriG brings about an optional application of a solution thermometer with memory function.