Tin Complexes of 4-(Benzylideneamino)benzenesulfonamide: Synthesis, Structure Elucidation and Their Efficiency as PVC Photostabilizers

Poly(vinyl chloride) (PVC) suffers from photo-oxidation and photodegradation when exposed to harsh conditions. Application of PVC thus relies on the development of ever more efficient photostabilizers. The current research reports the synthesis of new complexes of tin and their assessment as poly(vinyl chloride) photostabilizers. The three new complexes were obtained in high yields from reaction of 4-(benzylideneamino)benzenesulfonamide and tin chlorides. Their structures were elucidated using different tools. The complexes were mixed with poly(vinyl chloride) at a very low concentration and thin films were made from the blends. The effectiveness of the tin complexes as photostabilizers has been established using a variety of methods. The new tin complexes led to a decrease in weight loss, formation of small residues, molecular weight depression, and surface alteration of poly(vinyl chloride) after irradiation. The additives act by absorption of ultraviolet light, removal the active chlorine produced through a dehydrochlorination process, decomposition of peroxides, and coordination with the polymeric chains. The triphenyltin complex showed the greatest stabilizing effect against PVC photodegradation as a result of its high aromaticity.


Introduction
Plastic is a polymeric material that is widely used as an alternative for wood, glass, and metals in various applications [1,2]. Plastics are cheap to produce and have superior performance and unique properties compared with other materials [3]. Everyday applications include use in vehicles (e.g., airbags, child safety seats, and bicycle helmets), electronic equipment (e.g., computers, cell phones, and televisions), building construction (e.g., insulation, flooring, walls, and roofs), toys, and packaging. Polymers can occur in nature (e.g., rubber) or can be produced synthetically as in the case of poly(vinyl chloride) (PVC). They can be soft and flexible owing to low crystallinity or rigid with a high level of crystallinity [4].
PVC is a thermoplastic that is suitable for many applications thanks to its excellent performance and unique properties. Among synthetic polymers, it is only superseded by polyethylene and polypropylene in terms of production and consumption scales [5]. PVC is non-combustible as 57% of its weight is chlorine, and has many qualities that make it attractive for various outdoor applications [6]. However, sunlight and harsh conditions have a detrimental effect on PVC, leading to its photooxidation and photodegradation.

Synthesis of Complexes 1 and 2
A mixture of ligand (0.26 g, 1.0 mmol) and Ph 3 SnCl (0.39 g, 1.0 mmol) or Bu 3 SnCl (0.33 g, 1.0 mmol) in methanol (MeOH; 30 mL) was refluxed for six hours (Scheme 1). The solid obtained was filtered, washed with MeOH, and dried to afford 1 or 2 in good yields ( Table 1). The structures of 1 and 2 were confirmed using elemental analysis, FTIR, and NMR spectral data (See Section 3.1).

Synthesis of Complexes 1 and 2
A mixture of ligand (0.26 g, 1.0 mmol) and Ph3SnCl (0.39 g, 1.0 mmol) or Bu3SnCl (0.33 g, 1.0 mmol) in methanol (MeOH; 30 mL) was refluxed for six hours (Scheme 1). The solid obtained was filtered, washed with MeOH, and dried to afford 1 or 2 in good yields ( Table 1). The structures of 1 and 2 were confirmed using elemental analysis, FTIR, and NMR spectral data (See Section 3.1). Scheme 1. Synthesis of 1 and 2.

Synthesis of Complex 3
A mixture of ligand (0.52 g, 2.0 mmol) and Me2SnCl2 (0.22 g, 1.0 mmol) in MeOH (30 mL) was refluxed for eight hours (Scheme 2). The solid formed was filtered, washed with MeOH, and dried to give 3 in a 76% yield ( Table 1). The structure of 3 was confirmed using analytical and spectroscopic tools (Section 3.1). Scheme 2. Synthesis of 3.

Preparation of PVC Films
A mixture of PVC (5.0 g) and appropriate organotin complex (25 mg) in tetrahydrofuran (THF; 100 mL) was magnetically stirred for two hours at 25 °C. The mixture was poured onto a glass plate (15 holes, 4 × 4 cm 2 , and 40 µm thickness). The films obtained were left to dry for 18 h in a vacuum oven at room temperature.

Synthesis of Complex 3
A mixture of ligand (0.52 g, 2.0 mmol) and Me 2 SnCl 2 (0.22 g, 1.0 mmol) in MeOH (30 mL) was refluxed for eight hours (Scheme 2). The solid formed was filtered, washed with MeOH, and dried to give 3 in a 76% yield ( Table 1). The structure of 3 was confirmed using analytical and spectroscopic tools (Section 3.1).

Synthesis of Complexes 1 and 2
A mixture of ligand (0.26 g, 1.0 mmol) and Ph3SnCl (0.39 g, 1.0 mmol) or Bu3SnCl (0.33 g, 1.0 mmol) in methanol (MeOH; 30 mL) was refluxed for six hours (Scheme 1). The solid obtained was filtered, washed with MeOH, and dried to afford 1 or 2 in good yields ( Table 1). The structures of 1 and 2 were confirmed using elemental analysis, FTIR, and NMR spectral data (See Section 3.1). Scheme 1. Synthesis of 1 and 2.

Synthesis of Complex 3
A mixture of ligand (0.52 g, 2.0 mmol) and Me2SnCl2 (0.22 g, 1.0 mmol) in MeOH (30 mL) was refluxed for eight hours (Scheme 2). The solid formed was filtered, washed with MeOH, and dried to give 3 in a 76% yield ( Table 1). The structure of 3 was confirmed using analytical and spectroscopic tools (Section 3.1). Scheme 2. Synthesis of 3.

Preparation of PVC Films
A mixture of PVC (5.0 g) and appropriate organotin complex (25 mg) in tetrahydrofuran (THF; 100 mL) was magnetically stirred for two hours at 25 °C. The mixture was poured onto a glass plate (15 holes, 4 × 4 cm 2 , and 40 µm thickness). The films obtained were left to dry for 18 h in a vacuum oven at room temperature.

Preparation of PVC Films
A mixture of PVC (5.0 g) and appropriate organotin complex (25 mg) in tetrahydrofuran (THF; 100 mL) was magnetically stirred for two hours at 25 • C. The mixture was poured onto a glass plate (15 holes, 4 × 4 cm 2 , and 40 µm thickness). The films obtained were left to dry for 18 h in a vacuum oven at room temperature.

Assessment of PVC by FTIR Spectroscopy
FTIR spectroscopy was used to investigate the efficiency of organotin complexes as PVC antidegradation additives. Irradiation of PVC blends with UV light with a λ max of 313 nm for a period of 300 h leads to changes in their FTIR spectra. The intensity of absorption bands appearing at 1722 and 1604 cm −1 , corresponding to the carbonyl group (C=O) and alkene double bonds (C=C), respectively, were monitored during irradiation [16]. The growth in the intensity of these peaks was compared with that for the C-H bond (1328 cm −1 ). The intensity of the peak due to the C-H bond is not affected by irradiation. Such a comparison provides an assessment of PVC photodegradation and production of small residues containing C=O and C=C groups [44]. The functional group index (I s ) was calculated by dividing the absorbance (A s ) of a group by that for the C-H peak (A r ) using Equation (1).

Assessment of PVC Photodegradation by Weight Loss (%)
Irradiation of PVC blends leads to the production of small molecular weight fragments. As a result, a weight loss takes place and its percentage is highly dependent on the level of photodegradation. PVC weight loss (%) due to photoirradiation was calculated from the weight of films before (W 1 ) and after (W 2 ) irradiation using Equation (2) [45].

Assessment of PVC Photodegradation by Average Molecular Weight (M V )
Irradiation of PVC causes a decrease in its M V due to the formation of volatiles and small fragments. As a result, the intrinsic viscosity [η] of PVC drops. The depression in [η] is proportional to the damage occurring within PVC owing to irradiation. The M V of irradiated PVC was calculated using the Mark-Houwink relation shown in Equation (3) [46].
The 1 H NMR spectra of 1-3 showed the presence of aromatic, NH, and substituent (phenyl, n-butyl, and methyl) protons (Table 3). In addition, the 13 C NMR spectra confirmed the presence of all carbons in complexes 1-3 ( Table 4).
The 119 Sn NMR spectra of 1 and 2 ( Figures S5 and S6) showed a singlet at −227.4 ppm and −41.3 ppm, respectively. In contrast, the singlet signal appeared at −143.2 ppm for complex 3 ( Figure S7). The 119 Sn chemical shifts indicated that the coordination number for the tin atom was five in complexes 1 and 2 and six in complex 3 [49,50].

FESEM of Complexes 1-3
FESEM was used to assess the cross sections and variation of particle shape and size of complexes 1-3. The FESEM images showed that complexes 1-3 have porous structures in which pores varied in shape and size. In addition, they showed the presence of some small particle agglomerates ( Figure 1). The particle size of tin complexes was in the range of 480.6-664.4 nm for 1, 167.9-864.9 nm for 2, and 276.4-625.6 nm for 3.

Assessment of PVC Photodegradation by EDX Mapping
Complexes 1-3 (0.5% by weight) were mixed with PVC and films (thickness of 40 µm) were produced [51]. The PVC blends were exposed to light (λ max = 313 nm) for 300 h and the element content was analyzed using EDX mapping. The element composition of the blank PVC film is shown in Figure S8. The chlorine content within the PVC film dropped dramatically from 68.0% to 50.6% owing to irradiation. Photodegradation of PVC leads to bonds breaking and the release of HCl from the polymeric chains, indicating a substantial degree of dehydrochlorination [6]. After irradiation, the decrease in chlorine content (%) was low (54.2-51.1%) for the PVC blends containing complexes 1-3 ( Figure S9). Such a result revealed that the degree of PVC photodegradation was lower in the presence of 1-3 than that for the pure PVC film. The highest chlorine content (54.2%) was observed with the use of complex 1. Complex 1 contains five aromatic moieties (four phenyl and one 1,4-disubstituted benzene unit) and can absorb the UV light more efficiently. Polymers 2021, 13, 2434 6 of 18

Assessment of PVC Photodegradation by EDX Mapping
Complexes 1-3 (0.5% by weight) were mixed with PVC and films (thickness of 40 µm) were produced [51]. The PVC blends were exposed to light (λmax = 313 nm) for 300 h and the element content was analyzed using EDX mapping. The element composition of the blank PVC film is shown in Figure S8. The chlorine content within the PVC film dropped dramatically from 68.0% to 50.6% owing to irradiation. Photodegradation of PVC leads to bonds breaking and the release of HCl from the polymeric chains, indicating a substantial degree of dehydrochlorination [6]. After irradiation, the decrease in chlorine content (%) was low (54.2-51.1%) for the PVC blends containing complexes 1-3 (Figure

Assessment of PVC Photodegradation by FTIR Spectroscopy
Irradiation of PVC leads to the formation of chloride radicals responsible for the elimination of small fragments containing carbonyl (C=O) groups and alkene double (CH=CH) bonds, for example [52]. Therefore, PVC films were irradiated and the growth in the absorption peaks corresponding to C=O (1722 cm -1 ) and CH=CH (1604 cm -1 ) groups was measured and compared to that for the reference peak (C-H bond; 1328 cm -1 ). The FTIR spectra for the PVC (before and after irradiation) and PVC + 1 blend (after irradiation) are shown in Figure 2. The growth in the peaks for both C=O and CH=CH groups is used as a measure for the degree of PVC degradation that has taken place owing to irradiation. Figure 2 shows that the intensity of C=O and CH=CH peaks increased significantly owing to irradiation in the blank film compared with the PVC + 1 blend. Clearly, complex 1 leads to a reduction in degradation of PVC upon irradiation.
Irradiation of PVC leads to the formation of chloride radicals responsible for the elimination of small fragments containing carbonyl (C=O) groups and alkene double (CH=CH) bonds, for example [52]. Therefore, PVC films were irradiated and the growth in the absorption peaks corresponding to C=O (1722 cm -1 ) and CH=CH (1604 cm -1 ) groups was measured and compared to that for the reference peak (C-H bond; 1328 cm -1 ). The FTIR spectra for the PVC (before and after irradiation) and PVC + 1 blend (after irradiation) are shown in Figure 2. The growth in the peaks for both C=O and CH=CH groups is used as a measure for the degree of PVC degradation that has taken place owing to irradiation. Figure 2 shows that the intensity of C=O and CH=CH peaks increased significantly owing to irradiation in the blank film compared with the PVC + 1 blend. Clearly, complex 1 leads to a reduction in degradation of PVC upon irradiation.  The carbonyl (I C=O ) and polyene (I C=C ) indices were calculated using Equation (1) and plotted versus time at intervals of 50 h of irradiation. Figure 3 shows that the growth rate for the C=O and CH=CH groups was highest for the blank PVC and lowest for the blend containing 1. For example, I C=O and I C=C were 0.039 and 0.030, respectively, before irradiation; 0.268 and 0.351, respectively, after 50 h of irradiation; and 0.542 and 0.553, respectively, after 300 h of irradiation. For the PVC + 1 blend, the I C=O and I C=C were 0.049 and 0.147, respectively, after 50 h of irradiation compared with 0.215 and 0.271, respectively, after 300 h of irradiation. Clearly, the presence of complex 1, which has high aromaticity, substantially reduced the degradation of PVC. The effectiveness of tin complexes as PVC additives is highest for 1 (triphenyl substituted complex), followed by 2 (tributyl substituted complex), and 3 (dimethyl substituted complex) has the lowest. tion; 0.268 and 0.351, respectively, after 50 h of irradiation; and 0.542 and 0.553, respectively, after 300 h of irradiation. For the PVC + 1 blend, the IC=O and IC=C were 0.049 and 0.147, respectively, after 50 h of irradiation compared with 0.215 and 0.271, respectively, after 300 h of irradiation. Clearly, the presence of complex 1, which has high aromaticity, substantially reduced the degradation of PVC. The effectiveness of tin complexes as PVC additives is highest for 1 (triphenyl substituted complex), followed by 2 (tributyl substituted complex), and 3 (dimethyl substituted complex) has the lowest.

Assessment of PVC Photodegradation by Weight Loss
Oxidation, decomposition, and degradation of PVC lead to weight loss due to elimination of free radicals and HCl, bond cleavages, cross-linking, and production of volatile small molecular weight residues [15]. The percentage weight loss from PVC is used as a tool to assess the level of photodegradation. The percentage weight loss was calculated after every 50 h of irradiation using Equation (2) and the results are shown in Figure 4. The weight loss (%) increased linearly with the time of photoirradiation in all cases. The presence of the tin complexes reduces degradation. For example, the weight loss for the pure PVC film is 0.236% after 50 h and 0.804% after 300 h of photoirradiation compared with 0.067% and 0.357%, respectively, when 1 was present. Consistent with FTIR results, complex 1 provided the most protection for PVC compared with the other two complexes (i.e., 2 and 3).

Assessment of PVC Photodegradation by Weight Loss
Oxidation, decomposition, and degradation of PVC lead to weight loss due to elimination of free radicals and HCl, bond cleavages, cross-linking, and production of volatile small molecular weight residues [15]. The percentage weight loss from PVC is used as a tool to assess the level of photodegradation. The percentage weight loss was calculated after every 50 h of irradiation using Equation (2) and the results are shown in Figure 4. The weight loss (%) increased linearly with the time of photoirradiation in all cases. The presence of the tin complexes reduces degradation. For example, the weight loss for the pure PVC film is 0.236% after 50 h and 0.804% after 300 h of photoirradiation compared with 0.067% and 0.357%, respectively, when 1 was present. Consistent with FTIR results, complex 1 provided the most protection for PVC compared with the other two complexes (i.e., 2 and 3).

Assessment of PVC Photodegradation by the
Photoirradiation of PVC causes a decrease in its owing to chain scission [46,53]. A solution of irradiated PVC was made from the blends after every 50 h, in THF, and its

Assessment of PVC Photodegradation by the M V
Photoirradiation of PVC causes a decrease in its M V owing to chain scission [46,53]. A solution of irradiated PVC was made from the blends after every 50 h, in THF, and its viscosity was measured. Equation (3) was used to calculate the M V which is presented against time ( Figure 5). The decrease in the M V was highest for the pure PVC film. The M V for the pure PVC film decreased by 45% after the first 50 h, 86% after 200 h, and 94% at the end of the photoirradiation process. In the presence of 1, the M V decreased by 21% after the first 50 h, 60.3% after 200 h, and 71% after 300 h of photoirradiation. The result showed the stabilizing effect of tin complexes 1-3.

Photoirradiation of PVC causes a decrease in its
owing to chain scission [46,53]. A solution of irradiated PVC was made from the blends after every 50 h, in THF, and its viscosity was measured. Equation (3) was used to calculate the which is presented against time ( Figure 5). The decrease in the was highest for the pure PVC film. The for the pure PVC film decreased by 45% after the first 50 h, 86% after 200 h, and 94% at the end of the photoirradiation process. In the presence of 1, the decreased by 21% after the first 50 h, 60.3% after 200 h, and 71% after 300 h of photoirradiation. The result showed the stabilizing effect of tin complexes 1-3.

Assessment of PVC Photodegradation by Optical Microscopy
The surface morphology of PVC blends was investigated using a microscope to assess the damage due to photoirradiation. The optical images of the blank PVC surface before photoirradiation were smooth and regular with no cracks or discoloration. After irradiation, the surface showed cracks, white spots, darkened color, irregularity, and

Assessment of PVC Photodegradation by Optical Microscopy
The surface morphology of PVC blends was investigated using a microscope to assess the damage due to photoirradiation. The optical images of the blank PVC surface before photoirradiation were smooth and regular with no cracks or discoloration. After irradiation, the surface showed cracks, white spots, darkened color, irregularity, and roughness [43,54]. The changes due to photoirradiation are mainly a result of dehydrochlorination and elimination of volatiles and breaking of bond [55]. Figure 6 shows generally rough and irregular surfaces of PVC after irradiation with the appearance of dark spots and cracks. Inspection showed that the cracks were longer and deeper in the case of blank PVC film, indicating that the use of tin complexes 1-3 led to some stabilization of the polymeric films against photoirradiation. roughness [43,54]. The changes due to photoirradiation are mainly a result of dehydrochlorination and elimination of volatiles and breaking of bond [55]. Figure 6 shows generally rough and irregular surfaces of PVC after irradiation with the appearance of dark spots and cracks. Inspection showed that the cracks were longer and deeper in the case of blank PVC film, indicating that the use of tin complexes 1-3 led to some stabilization of the polymeric films against photoirradiation. Figure 6. Microscope images of PVC films after irradiation at 300 h.

Assessment of PVC Photodegradation by the FESEM
The surface of the irradiated and non-irradiated PVC films was inspected using FESEM, which provides high resolution images. Figure 7 clearly shows that the surface of the pure PVC film was badly damaged after irradiation. The surface was irregular, not homogeneous, lumpy, and contained cracks of different shapes and sizes after irradiation. For the pure PVC film, the particles size was 94.9-190.5 nm before irradiation compared with 101.7-116.1 nm after irradiation. Figure 8 shows that the surface of films containing tin complexes 1-3 after irradiation was more regular, smoother, and less lumpy with a high degree of homogeneity. Clearly, additives 1 and 2 have most efficiently stabilized PVC followed by 3. The additives substantially reduced PVC photodegradation. After irradiation (300 h), the particles size was 76.4-144.7 nm for PVC + 1, 189.2-278.3 nm for PVC + 2, and 66.6-146.9 nm for PVC + 3.

Assessment of PVC Photodegradation by the FESEM
The surface of the irradiated and non-irradiated PVC films was inspected using FESEM, which provides high resolution images. Figure 7 clearly shows that the surface of the pure PVC film was badly damaged after irradiation. The surface was irregular, not homogeneous, lumpy, and contained cracks of different shapes and sizes after irradiation. For the pure PVC film, the particles size was 94.9-190.5 nm before irradiation compared with 101.7-116.1 nm after irradiation. Figure 8 shows that the surface of films containing tin complexes 1-3 after irradiation was more regular, smoother, and less lumpy with a high degree of homogeneity. Clearly, additives 1 and 2 have most efficiently stabilized PVC followed by 3. The additives substantially reduced PVC photodegradation. After irradiation (300 h), the particles size was 76.4-144.7 nm for PVC + 1, 189.2-278.3 nm for PVC + 2, and 66.6-146.9 nm for PVC + 3. spots and cracks. Inspection showed that the cracks were longer and deeper in the case of blank PVC film, indicating that the use of tin complexes 1-3 led to some stabilization of the polymeric films against photoirradiation.

Assessment of PVC Photodegradation by the FESEM
The surface of the irradiated and non-irradiated PVC films was inspected using FESEM, which provides high resolution images. Figure 7 clearly shows that the surface of the pure PVC film was badly damaged after irradiation. The surface was irregular, not homogeneous, lumpy, and contained cracks of different shapes and sizes after irradiation. For the pure PVC film, the particles size was 94.9-190.5 nm before irradiation compared with 101.7-116.1 nm after irradiation. Figure 8 shows that the surface of films containing tin complexes 1-3 after irradiation was more regular, smoother, and less lumpy with a high degree of homogeneity. Clearly, additives 1 and 2 have most efficiently stabilized PVC followed by 3. The additives substantially reduced PVC photodegradation. After irradiation (300 h), the particles size was 76.4-144.7 nm for PVC + 1, 189.2-278.3 nm for PVC + 2, and 66.6-146.9 nm for PVC + 3.

Assessment of PVC Photodegradation by the AFM
The roughness of the PVC surface was examined further using AFM, whic two-and three-dimensional topography. Figures 9 and 10 indicated that the

Assessment of PVC Photodegradation by the AFM
The roughness of the PVC surface was examined further using AFM, which provides two-and three-dimensional topography. Figures 9 and 10 indicated that the surface of irradiated blends containing 1-3 was less rough compared with the pure PVC film. The use of complexes 1-3 as PVC additives led to a significant decrease in the rate of both dehydrochlorination and bond breaking of polymeric chains. The roughness factor (Rq) for irradiated pure PVC was 320.8 compared with 17.4, 37.2, and 41.1 for PVC + 1, PVC + 2, and PVC + 3, respectively. Clearly, the Rq for the PVC surface decreased significantly in the presence of 1-3. The use of complex 1 led to a drop in the Rq by 18.4-fold, which is one of the highest compared with those reported [56][57][58][59][60][61][62][63][64]. For example, the fold decrease in the Rq was 3.3-6.0 using Schiff bases [56][57][58], 5.2-16.6 using organotin complexes [59][60][61][62][63], and 16.8 using polyphosphates [64]. However, the use of tin complexes containing naphthalene sulfonic acid led to a remarkable decrease in the Rq of PVC up to 59.9-fold, possibly owing to the extended conjugation within the aromatic system of naphthalene [43]. one of the highest compared with those reported [56][57][58][59][60][61][62][63][64]. For example, the fold decrease in the Rq was 3.3-6.0 using Schiff bases [56][57][58], 5.2-16.6 using organotin complexes [59][60][61][62][63], and 16.8 using polyphosphates [64]. However, the use of tin complexes containing naphthalene sulfonic acid led to a remarkable decrease in the Rq of PVC up to 59.9-fold, possibly owing to the extended conjugation within the aromatic system of naphthalene [43].

Suggested Mechanisms of the Role Played by Organotin Complexes as PVC Photostabilizers
The use of tin complexes 1-3 as additives leads to a substantial reduction in the degradation and decomposition of PVC films. Complex 1, which has the highest aromatic content (triphenyl substituents), leads to the most noticeable stabilizing effect, followed by 2 (tri-n-butyl substituents) and then 3 (dimethyl substituents). Complexes 1-3 act as PVC photostabilizers mainly owing to the presence of aromatic moieties, heteroatoms, and tin atoms. Complexes 1-3 can absorb UV light and release the adsorbed energy slowly over time without harming the PVC chains. The highly energetic states produced thanks to the absorption of UV light by PVC can also be stabilized through resonance of aromatic rings [65]. In addition, the tin atom is highly acidic and can scavenge HCl (Figure 11a) [61].

Suggested Mechanisms of the Role Played by Organotin Complexes as PVC Photostabilizers
The use of tin complexes 1-3 as additives leads to a substantial reduction in the degradation and decomposition of PVC films. Complex 1, which has the highest aromatic content (triphenyl substituents), leads to the most noticeable stabilizing effect, followed by 2 (tri-n-butyl substituents) and then 3 (dimethyl substituents). Complexes 1-3 act as PVC photostabilizers mainly owing to the presence of aromatic moieties, heteroatoms, and tin atoms. Complexes 1-3 can absorb UV light and release the adsorbed energy slowly over time without harming the PVC chains. The highly energetic states produced thanks to the absorption of UV light by PVC can also be stabilized through resonance of aromatic rings [65]. In addition, the tin atom is highly acidic and can scavenge HCl (Figure 11a) [61]. Photooxidation of PVC occurs in the presence of oxygen-containing species such as hydroperoxides (PO2H) [66]. Tin complexes inhibit photooxidation by decomposing hydroperoxides (Figure 11b).
Various PVC photooxidation products are generated owing to the formation of peroxide radicals (POO • ), which are also known as chromophores. Tin complexes 1-3 react with chromophores to produce highly stable intermediates (Figure 11c) through resonance of the aromatic rings within additives [66,67]. Therefore, complexes 1-3, and in particular 1, can inhibit PVC photooxidation and thus enhance the photostability of the polymeric material.
The interaction between polarized atoms of the C-Cl bonds in PVC and the N-H, O=S=O, and CH=N bonds in complexes 1-3 could stabilize the polymer against photodegradation ( Figure 12). Such coordination could help the energy transfer from PVC to tin complexes before it is dissipated. However, such a hypothesis neglects the steric hindrance complications in macromolecules [68].  Photooxidation of PVC occurs in the presence of oxygen-containing species such as hydroperoxides (PO 2 H) [66]. Tin complexes inhibit photooxidation by decomposing hydroperoxides (Figure 11b).
Various PVC photooxidation products are generated owing to the formation of peroxide radicals (POO • ), which are also known as chromophores. Tin complexes 1-3 react with chromophores to produce highly stable intermediates (Figure 11c) through resonance of the aromatic rings within additives [66,67]. Therefore, complexes 1-3, and in particular 1, can inhibit PVC photooxidation and thus enhance the photostability of the polymeric material.
The interaction between polarized atoms of the C-Cl bonds in PVC and the N-H, O=S=O, and CH=N bonds in complexes 1-3 could stabilize the polymer against photodegradation ( Figure 12). Such coordination could help the energy transfer from PVC to tin complexes before it is dissipated. However, such a hypothesis neglects the steric hindrance complications in macromolecules [68]. Photooxidation of PVC occurs in the presence of oxygen-containing species such as hydroperoxides (PO2H) [66]. Tin complexes inhibit photooxidation by decomposing hydroperoxides (Figure 11b).
Various PVC photooxidation products are generated owing to the formation of peroxide radicals (POO • ), which are also known as chromophores. Tin complexes 1-3 react with chromophores to produce highly stable intermediates (Figure 11c) through resonance of the aromatic rings within additives [66,67]. Therefore, complexes 1-3, and in particular 1, can inhibit PVC photooxidation and thus enhance the photostability of the polymeric material.
The interaction between polarized atoms of the C-Cl bonds in PVC and the N-H, O=S=O, and CH=N bonds in complexes 1-3 could stabilize the polymer against photodegradation ( Figure 12). Such coordination could help the energy transfer from PVC to tin complexes before it is dissipated. However, such a hypothesis neglects the steric hindrance complications in macromolecules [68].

Conclusions
Three new tin complexes were synthesized in good yields from the reaction of substituted tin chlorides and 4-(benzylideneamino)benzenesulfonamide. The structures and elemental contents of the tin complexes were established and their surface morphologies were investigated. The polymer weight loss, depression in molecular weight, production of fragments containing a carbonyl group or a C=C double bond, and surface morphology were investigated by comparison of pre-and post-irradiation PVC. The blank PVC film suffers a significant degree of photooxidation and photodegradation as a result of long-term irradiation. On the other hand, PVC blends containing tin complexes showed a reduced level of undesirable changes post-irradiation when compared with the blank film. Thus, the tin complexes synthesized, and in particular the complex containing the triphenyl substituent, act as effective and efficient PVC photostabilizers and enhance photostability.