Hybrid Sol-gel Coatings for Corrosion Mitigation: A Critical Review.

The corrosion process is a major source of metallic material degradation, particularly in aggressive environments, such as marine ones. Corrosion progression affects the service life of a given metallic structure, which may end in structural failure, leakage, product loss and environmental pollution linked to large financial costs. According to NACE, the annual cost of corrosion worldwide was estimated, in 2016, to be around 3%–4% of the world’s gross domestic product. Therefore, the use of methodologies for corrosion mitigation are extremely important. The approaches used can be passive or active. A passive approach is preventive and may be achieved by emplacing a barrier layer, such as a coating that hinders the contact of the metallic substrate with the aggressive environment. An active approach is generally employed when the corrosion is set in. That seeks to reduce the corrosion rate when the protective barrier is already damaged and the aggressive species (i.e., corrosive agents) are in contact with the metallic substrate. In this case, this is more a remediation methodology than a preventive action, such as the use of coatings. The sol-gel synthesis process, over the past few decades, gained remarkable importance in diverse areas of application. Sol–gel allows the combination of inorganic and organic materials in a single-phase and has led to the development of organic–inorganic hybrid (OIH) coatings for several applications, including for corrosion mitigation. This manuscript succinctly reviews the fundamentals of sol–gel concepts and the parameters that influence the processing techniques. The state-of-the-art of the OIH sol–gel coatings reported in the last few years for corrosion protection, are also assessed. Lastly, a brief perspective on the limitations, standing challenges and future perspectives of the field are critically discussed.


Introduction
The sol-gel synthesis process is a versatile method used to produce a wide diversity of materials, which range from inorganic glasses to complex organic-inorganic hybrid (OIH) materials [1][2][3][4][5][6][7]. Specific types of OIH materials have also been named, either as ORMOSILs (acronym created from organically modified silicates) or OMOCERs (from organically modified ceramics) depending on the precursors employed and on the synthesis route. OIH materials may be described as multicomponent compounds that have at least one of their organic and inorganic components in the sub-micrometric and/or in the nanometric size domain (Figure 1) [8]. The properties of the OIH materials are not the simple addition of the contribution of each individual component; instead, their properties result from the synergy created between the two components (i.e., organic and inorganic). Basically, to synthesize OIH materials through sol-gel method, it is required to introduce molecular precursors which allow the formation of the organic component. This can be achieved by [2,[9][10][11][12]: 1) Adding organic precursors that are soluble in the reactional media (where hydrolysis/condensation reactions take place), although do not take part in the gel formation. The OIH material obtained corrosion rate and mitigate the development of further corrosion degradation of the metallic substrates. Nevertheless, it is accepted worldwide that only the combination of both methodologies can provide a reliable and durable protection of the metallic substrates against corrosion. Thus, the development of coatings that effectively prevent, mitigate and delay the corrosion process are of extreme importance. A material to be used as a protective coating must include several properties; namely, effective corrosion protection, abrasion and cracking resistance, good adhesion between the metallic surface and the coating and a long-life span. Simple OIH coatings can improve the adherence between the substrate and organic based coatings, for instance. Nevertheless, they behave only as a physical barrier. To obtain OIH with anticorrosive performance, additional functions must be introduced within the OIH network, such as corrosion inhibitors [16,[49][50][51]. The alternatives proposed in the literature include OIH materials containing corrosion inhibitors such as zirconium [33,[52][53][54][55][56], titanium [30,57,58] and cerium [50,55,59]. M. Catauro et al. synthesized OIH sol-gel materials based on zirconia (ZrO 2 ) and poly(ε-caprolactone) to coat pure titanium for implants application [56]. The authors concluded that the OIH films were suitable to coat the metallic implants, to improve their bioactivity and maintain the passivation properties of the metallic substrate. Later, the same authors reported the synthesis of OIH materials by sol-gel method using TiO 2 for the inorganic matrix and poly(ε-caprolactone) as organic component. The material produced was used to improve the performance of Ti6Al4V implants [58].
The current review includes four main sections: the first section is dedicated to the concepts of sol-gel process from a historical perspective. The second section describes the fundamentals of the sol-gel method. The third section covers, succinctly, the main progress on the development of OIH sol-gel coatings for corrosion mitigation, including self-healing, anti-fouling and superhydrophobic functions. Finally, the fourth section outlines the challenges and prospects for future research.

Sol-gel Process: A Historical Perspective and Applications
This section will briefly focus on the historical perspective of the first industrial interest in sol-gel materials, followed by their commercialization as coatings. A detailed and very complete historical perception on the evolution of OIH material can be found elsewhere [78].
The commercialization of sol-gel coatings appeared about a century after publication of the first scientific papers with Ebelman and Graham's studies, in 1846, on silica gels [79]. Although noticed as early as 1846, and known to play a part in natural processes (e.g., formation of opal, glasses and ceramics), it was only during the post-World War II period that the solution-sol-gel, commonly known as the sol-gel process, became increasingly exploited for the preparation of glasses and other ceramic materials [80]. Graham (1861) is generally considered as being the founder of colloidal materials science [81]. However, the oldest sols prepared in a lab were made of gold colloidal particles, by Faraday in 1853 [82]. Later, in 1919, W.A. Patrick submitted a patent of a gas mask canister for vapors' and gases' adsorption. The innovative part of this patent was the silica-gel made of sodium silicate [83]. In the late 1930s, Geffcken and Dislich from Schott Glaswerke Company, developed the basis of the dip coating process to cover industrial glass with thin oxide layers [84]. The re-introduced attention in the sol-gel process was mainly due to the need for obtaining optical glass components (e.g., lenses, mirrors) at low temperatures without subsequent polishing. Additionally, the opportunity for modifying the materials structures at a nanoscale level ( Figure 1) lead to the synthesis of advanced ceramics. From the 1940s until the end of the 1970s, the advances using the sol-gel process were mainly focused on the development of mixed OIH materials [78]. At that time, some labs, such as atomic energy in the United States of America, had already applied the sol-gel route to produce pellets and fuel powders. However, the work developed stayed secret until the 1970s [84]. From the 1980s until nowadays, a huge development in the sol-gel process was achieved. The research conducted allowed them to obtain OIH materials with applications in a wide range of areas, such as chemical and biosensors [13,85,86], in several transduction modes, from electrochemical [87][88][89][90][91] to optical [13,[92][93][94][95]; biomaterials for drug delivery [24,[96][97][98][99][100]; materials for improving bioactivity and biocompatibility of metallic substrates [101][102][103][104][105][106][107][108]; electronics [14]; environment [109][110][111]; optics [13,112,113]; medicine [53, [114][115][116][117]; functional smart coatings [31,38,73,118]; fuel and solar cells [119][120][121][122]; and catalysts [123,124] (Figure 2). In 2018, Nourani-Vatani et al. [53] reported that a huge development for hospital equipment, and medical, dental and laboratorial devices using different metallic alloys has been achieved. However, such metallic alloys show some limitations, including low corrosion/wear resistance and unsuitable scratching and hardness properties. Therefore, to solve these drawbacks, several coatings have been proposed [57,101,105,108]. It was also concluded that zirconium-based coatings and OIH materials have been widely studied, as has the application, simultaneously, of polymers and zirconium enhanced several properties; namely, scratching, biocompatibility, bioactivity and hardness [53]. The sol-gel method offers several advantages when compared to traditional synthesis processes [1,36,[125][126][127]; namely, the ease of fabrication and flexibility of the process, the large number of precursor reagents commercially available with tuned functional groups and the low environmental impact. Furthermore, sol-gel also allows for excellent control of the stoichiometry of the precursor; and the incorporation of different components that introduce complementary functions to the material (Figure 2), such as UV protection [128][129][130], anti-fouling [131,132], anti-reflection [133,134], moisture resistance [135], corrosion protection [15,16,31,38,[136][137][138] and detection of biological components [88,139]-proteins [140] and enzymes [92,141], antibodies [142,143], DNA [95,144,145], polysaccharides [146,147], etc. This feature allows one to obtain, in a simple way, smart and multifunctional materials. Nowadays, the development of OIH sol-gel materials is mostly focused on green [37,49,148], safe, smart [37, 149,150] and economic approaches. Ideally, these new materials should be intelligent, with properties such as self-healing abilities [73,[151][152][153] or the capacity to act according with a certain environment/need or property (stimuli-responsive). OIH materials with the ability of reacting to different stimuli, such as mechanical, chemical, optical, electric and thermal ones, in order to mitigate undesired changes, is the focus of most research reported. The search for materials with the capacity to heal, adapt and behave according to each need and environment-multifunctionality-will mark the 21st century achievements.

General Concepts of the Sol-gel Process.
The sol-gel synthesis process has been widely reported in the literature [1,2,15,38,[154][155][156]. Therefore, in the present manuscript, only a generic approach on the sol-gel fundamentals will be conducted.
Over the last five decades, an exhaustive development of the synthetic approaches to various oxide materials has been based on the polymerization of metal alkoxides, M(OR) n , namely, silicon (Si), such as tetraethoxysilane (TEOS) or tetramethoxysilane (TMOS). This process is influenced by several factors; namely: pH, temperature, catalyst, solvent, nature of alkyl group, water to alkoxide molar ratio, etc. Alkoxysilanes generally show a slow kinetic rate when compared to the titanium, aluminum or zirconium alkoxides. This allows a higher chemical control of the process, leading to materials with different properties, such as pore size and distribution, dimension and shape of the particles. Furthermore, silicon shows lower reactivity regarding chelating groups and redox process, which may lead to the formation of sub-products [157]. Table 1 shows chemical structures of the most-used silicon alkoxide precursors in the synthesis of OIH materials. The precursors with polymerizable functional groups, e.g., epoxide (GPTMS), vinyl (VTMS) or methacrylate (MAPTS), besides allowing the formation of an organic network, also contribute to further densification of the OIH material.

3-Methacryloxypropyltrimethoxysilane MAPTS
The chemical reactions involved in the sol-gel process are usually divided into two steps. The first step involves the hydrolysis of metal alkoxides producing hydroxyl groups in the presence of water. The second step is followed by polycondensation of the resulting hydroxyl groups and residual alkoxyl groups, forming a three-dimensional (3D) network, establishing covalent bonds Si-O-Si in the case of silicon alkoxides. Therefore, the alkoxides and esters of inorganic acids are raw materials of utmost importance in the sol-gel technology. In the case of silicon alkoxides, the hydrolysis and condensation reactions may be catalyzed by acids or bases [158]. The structure and morphology of the final material is strongly dependent on the nature of the catalyst and pH of the reaction. The hydrolysis reactions, either catalyzed by acids or bases, are nucleophilic substitution reactions type S N 2, characterized by a transition state in which the silicon atom is penta-coordinated. The replacement extension of the OR groups by OH groups in the silicon atoms depends on the molar ratio Si/H 2 O: For acidic catalysis, the following reaction takes place: For basic catalysis, the following reaction takes place: The condensation reaction of Si(OR) 4-n (OH) n may also be catalyzed by acids or basis. The reactions for acidic catalysis are: The reaction mechanism of condensation by acidic catalysis starts with the protonation of the silanol species ending with the formation of a Si-O-Si bond. The reactions for alkaline catalysis are: For alkaline catalysis, the specie HO − removes the proton from the silanol group, forming a silanolate anion ending with the formation of a Si-O-Si bond. The reactions of alkoxysilanes, in which monomers form polymeric structures by loss of substituents, involve the formation of a colloidal suspension-Sol-followed by the polymerization that will lead to the formation of a 3D structure-gel. For acid catalysis, the alkoxysilane hydrolysis rate shows higher kinetics when compared to basic catalysis. Therefore, the acidic catalysis leads to the formation of a highly branched polymeric structure, while alkaline catalysis leads to colloidal particles with linear chains or a ringed shape. Once the gel is formed, the hybrid network needs to be dried in order to remove the water, alcohol and solvents that are formed during the hydrolysis/condensation reactions.
The drying step has an important role, since, depending on the process used, different materials will be obtained. For instance, if the drying process takes place under normal conditions, a contraction of the gelled network occurs. The obtained dry gel, which is known as xerogel, may shrink between five to ten times in volume when compared to the gel before drying. The shrinkage process includes the transport of the liquid through the pores of structure and contraction of the network [1,15,38]. The xerogel is suitable for substrate catalysis, filters, among other applications, mainly due to low porosity and large surface area [131]. Several studies have been reported concerning the use of xerogels in the field of filters and membranes [159] and for carbon dioxide capture [160]. If the drying of the gel occurs in wet supercritical conditions, the shrinkage will be minimal, and the resulting product is porous and is known as an aerogel [1,111,161]. The material is known as a monolith if the dimensions of the gel are greater than scarcely millimeters [1,[162][163][164]. In case of the gelation, it takes place by quick evaporation of the solvents; the materials obtained are coatings (Figure 3), films and fibers [14,154,165]. Nevertheless, it should be kept in mind that during the loss of volatile by-products, formed through the hydrolysis and condensation reactions, controlling the sample shrinkage during the 3D network development may be challenging and puzzling [1,6,7]. This type of material, composed by organic and inorganic components and known as OIH, is extremely attractive, since it enables an interface between two worlds of chemistry (organic and inorganic), each with unique properties that cannot be found on the individual components.

Hybrid Sol-gel Coatings for Corrosion Mitigation
OIHs have numerous remarkable and attractive properties with application in a wide range of fields ( Figure 2). However, the huge interest involved in the development of such materials is mainly due to the convenience of the synthesis process. The sol-gel method is a flexible and simple route that allows one to obtain OIH materials in different forms (films, fibers, nanoparticles (NPs), etc.). This synthesis route is exceptionally valuable for the design and production of OIH coatings. Furthermore, sol-gel synthesis route allows one to control, strictly, the precursor stoichiometry, to modify and introduce functional groups or encapsulate different elements. Moreover, it allows one to coat substrates with large surface areas and minimum complex geometries involving simple and inexpensive equipment, as illustrated in Figure 3. It is a process that involves the ability to manipulate nanostructural ( Figure 1) properties by controlling the hydrolysis, condensation reactions ( Figure 4) and aggregation processes. The properties of OIH sol-gel materials, such as homogeneity, stability and transparency, are largely dominated by the concentrations and types of precursors, the solvent's nature, the concentrations and types of additives (surfactants, catalysts, etc.), the pH of the reactional media, the heat treatment and the curing time [37,166]. Furthermore, the OIH gel network can be modified with a vast number of dopants [155,[167][168][169][170] leading to products with singular and extraordinary properties.
The nature of each of the interactions between the organic and inorganic components, within the hybrid networks, was used to establish an OIH classification. The first classification was introduced in 1994 by Sanchez and Ribot [3] and the OIH materials were divided into two classes (class I and II). Later, in 1997, Wojcik and Klein [171] introduced a three class system. OIH materials from class I are the ones where the interactions established between the organic and inorganic components are weak (e.g., hydrogen and ionic bonds, van der Walls bonds, π − π interactions). OIH materials from class II establish strong bonds between the organic and inorganic components, such as covalent bonds. OIH class III are the ones that comprise both the type of bonds established in OIH materials from class I and II.
The requirements for a material to be used as a coating for corrosion mitigation must include effective protection against corrosion, abrasion resistance and a good adhesion between the coating and the substrate surface. The OIHs class II show properties such as high hydrophobicity, good corrosion protection, low dielectric constants or good scratch resistance [12,31]. Therefore, these chemical and physical properties make the OIH class II the ones more suitable to mitigate corrosion/oxidation of the metallic substrates. OIH class II can be easily prepared by the sol-gel process in which the alkoxysilane precursor, generally a trialkoxysilane, has an alkyl group bonded to the silicon atom producing monomers in R'Si(OR) 3 in which R' may be H, CH 3 , CH 2 CH 3 or an aromatic group (Table 1). This alkyl group, by establishing a bond C-Si does not react (e.g., hydrolysis/condensation reactions) and remains covalently bonded to the silicon groups, through the C-Si bond, making part of the final material structure (Figure 4). These materials, known as polysilsesquioxane (R'SiO 1.5 ) [172][173][174] have desirable properties, such as good hydrophobicity and chemical and thermal stability. The organic groups R' are network modifiers and reduce the functionality of the silicon atoms, turning the silica network less brittle and rigid [175]. Another example of this type of material consists of the incorporation of a polydimethylsiloxane (PDMS) network linked to the SiO 2 network by the co-condensation of PDMS oligomers in a sol-gel reaction [176,177]. Monomers R'Si(OR) 3 , in which R' is an organic reactive group, such as amine, isocyanate, vinyl or epoxide (Table 1), may be used to obtain polysilsesquioxanes by sol-gel. The organic groups, through the combination of suitable monomers, may allow the formation of bridges between the silicate groups [175]. Examples of these types of products were reported by different authors [16,17,162,164]. In the last fifteen years, several review articles have been published in the design and application of OIH materials, and mostly were approached from the point of view of materials [2,3,12,27,36,112,148,[178][179][180][181][182]. Table 2 shows the most relevant review manuscripts published since 2016 focused on OIH sol-gel materials. Principles and morphologies of microcapsules, purpose of microencapsulation,physical, and chemical techniques and healing mechanisms for the coating industry were debated. [184] The progress made in the synthesis of several sol-gel-derived materials was reviewed.
The main achievements in the field of anticorrosion coatings were also debated.
[37] Summary of the main research achievements in the development, of OIH sol-gel coatings for corrosion mitigation of steel and aluminum substrates. [185] The general features of OIH coatings, and recent developments were summarized. [137] Summary of the latest achievements and strategies for the sol-gel process parameters and other factors that influence the corrosion properties of the OIH coatings for corrosion protection of aluminum-based alloys. [20] Overview of sol-gel technology where the fabric functions that can be achieved by this technology are debated including anticorrosion coatings.
2017 [186] Advances in smart coatings, including OIH coatings, with response to different stimuli and damage modes were reviewed. Emphasis was on corrosion sensing, self-cleaning, anti-fouling, and self-healing polymeric coating systems.
[187] Recent applications using PDMS polymers for anticorrosion, anti-biofouling, anti-icing, flame-resistant and self-cleaning, anti-reflection were reviewed. [188] Overview of the superhydrophobic coatings (including OIH sol-gel) reported in literature for steel protection and their performances.
2018 [138] Different solutions for slow down the corrosion processes of metallic substrates by using the oxides and doped oxides obtained by the sol-gel method were discussed. [189] Analysis of some of the most representative examples of the application of electrochemical techniques such as EIS, PDP; SVET, SIET, SKP and LEIS to determine the exact mechanism of protection offered by sol-gel coatings on metallic substrates. [78] Description of the historical perception of OIH material science. The major periods linked to the genesis of OIH materials were discussed.

Sol-gel Coatings with Self-healing Function
In the last few years, the interest in developing materials with self-healing ability led to outstanding developments [64,152,[226][227][228][229][230]. Self-healing ability can be achieved at different levels of the coating system and by different strategies [231] and is known as the ability of a coating, in a certain environment, repair damaged areas due to external factors ( Figure 5). According to Hia et al. [232] self-healing coatings may be classified into two types: intrinsic and extrinsic. Intrinsic coatings are the ones with a latent self-healing functionality and have the ability of heal the coatings matrices by themselves. Extrinsic coatings have a healing agent microencapsulated and embedded within the coating matrix. In this case, when the microcapsules are ruptured by damage, pH or another trigger, the healing agent is released and seals the damaged region, and the healing reaction takes place. Strategies such as the addition of polymerizable agents [69,209] to restore/heal the damage in a polymeric coating or the inclusion of corrosion inhibitors ( Figure 5) [50, 153,221,234] to stop the damage spread have been reported. Metals such as cerium [50,59,200,220,[235][236][237][238], lanthanum [239][240][241] or zirconium [33,53] have been incorporated in OIH sol-gel coatings in order to stop corrosion propagation [234,236,237,242,243]. Studies based on OIH coatings doped with cerium inhibitors have been reported since 2002 [235,244]. However, this review will focus only on the publications performed after 2015. Concerning the use of cerium as a corrosion inhibitor, the authors L.R.V. et al. [50] in 2017 performed a comparative study on the effect of CeO 2 NPs and Ce(III) ions as corrosion inhibitors in silica-alumina OIH sol-gel coatings. The coatings doped with cerium nitrate (Ce(NO 3 ) 3 ) showed poorer corrosion behavior when compared to CeO 2 NPs. The authors attributed this difference to the leaching out of Ce(III) ions in case of coatings doped with Ce(NO 3 ) 3 . This behavior was not reported for coatings doped with CeO 2 NPs. It was also concluded that the coatings doped with CeO 2 NPs were more "compact," minimizing the electrolyte ingress and therefore providing improved protection. U. Tiringer et al. [220] produced OIH sol-gel coatings, based on TEOS and GPTMS precursors and containing SiO 2 particles and Ce(NO 3 ) 3 for corrosion mitigation of aluminum alloy AA7075 in the presence of Cl − . The authors concluded that the curing procedure affected the coating properties obtaining coatings with lower roughness, reduced thickness and higher density by using a curing heating ramp. The incorporation of Ce(NO 3 ) 3 increased the roughness and thickness linked to a network with higher porosity. The authors showed that the porosity allowed the release and migration of the incorporated Ce(III) ions. The electrochemical data indicated that the coatings doped with Ce(NO 3 ) 3 and cured with heating ramp exhibited improved corrosion properties. Later, in 2019 the same authors [238], reported the synthesis of OIH sol-gel coatings based on the same precursors also doped and undoped with Ce(NO 3 ) 3 . The effects of curing temperature and the addition of Ce(NO 3 ) 3 on the degree of polycondensation of the OIH sols were studied. It was concluded that the addition of Ce(NO 3 ) 3 did not affect the viscosity of sols and improved their thermal stability. Furthermore, the authors revealed that the addition of Ce(NO 3 ) 3 acted as an initiator, stimulating the polycondensation reaction at lower temperatures. Earlier this year [59], T.T. Thai, et al. developed OIH sol-gel coatings doped with Ce (III) ions by using montmorillonite as container. The electrochemical studies showed that the coatings were effective at protecting the metallic substrate. At a low concentration of cerium-modified clay particles (0.5% wt.), the Ce (III) played a role as effective cathodic inhibitor of the metallic substrate. The leached cerium rate obtained was about 70%, and the authors showed that it was from the Ce(III) ions that were deposited, in the beginning, on the external layer of the clay platelets. In the end, it was concluded that the Ce(III) ions at the external layer of clay platelets induced the formation of Ce(OH) 2 , strengthening the corrosion protection of the OIH coating [59].
In the case of using lanthanum as a corrosion inhibitor, P. Balan et al. [240] in 2016 reported a study on the electrochemical behavior of modified silane films with lanthanum triflate salt (LTS) and/or silica NPs. The incorporation of LTS or silica NPs enhanced the anti-corrosion behavior of the silane films when compared to pure films. The films modified by both LTS and silica NPs showed improved corrosion protection. The authors also concluded that the direct addition LTS could compromise the coating barrier properties and the stability of the silane solution. These limitations were improved by incorporating La 3+ cations in amorphous silica NPs before being embedded into the silane film. Two years later, J. Peña-Poza et al. [241] studied TEOS sol-gel based coatings doped with lanthanum acetate/nitrate on different metallic substrates (i.e., copper, bronze, lead and steel). The authors concluded that La 2 O 3 was adequate to incorporate La 3+ ions within the silica matrix. Furthermore, the produced coatings mitigated the corrosion process on copper, bronze and lead, while steel substrates required thicker coatings.
Ideally, the addition of species (e.g., corrosion inhibitors and polymerizable species) to improve the OIH coating's performance must be incorporated within the coating matrix and released when required, i.e., when corrosion the process initiates, in order to delay further corrosion development. It has been reported in different studies that the direct incorporation of these species may interfere with the curing of the coating material and compromise its physico-chemical performances [16,203,245]. Therefore, the selection of suitable carriers/nanocontainers, to ensure their release in response to a trigger (stimulus-responsive), is of extreme importance [67,151,228]. The trigger which can be physical or chemical (i.e., crack propagation, the presence of moisture, pH, aggressive species) [227,235,[246][247][248][249][250]. Furthermore, these nanocontainers must be able to stock the required species in sufficient amounts and be compatible with the coating itself. The most commonly used reservoirs reported in the literature include urea-formaldehyde capsules [246][247][248][249], hydroxyapatite particles [57,251], chitosan [243,252] and halloysite nanotubes [213,221]. Several OIH sol-gel coatings have been reported as smart with self-healing abilities, such as the remarkable works reported by the M.G.S. Ferreira group [63,76,149,150,[253][254][255][256][257][258] and Adsul et al. [66,213,259].
Adsul et al. [66,213] studied the effect of loading cationic corrosion inhibitors (Ce 3+ /Zr 4+ ) into halloysite nanotubes, which were afterwards incorporated within an OIH sol-gel matrix and deposited on magnesium alloy substrates. The authors concluded the Ce 3+ /Zr 4+ loaded halloysite nanotubes dispersed within the OIH coating provided suitable corrosion protection of the substrate when exposed to 3.5% NaCl. The healing properties were confirmed through weight loss and electrochemical techniques. The same research group [259] also studied the incorporation of the same corrosion inhibitors into aluminum pillared montmorillonite clay. The montmorillonite clay was dispersed as received within the matrix sol-gel coatings. The coatings mitigated the corrosion process during the beginning of exposure to aggressive environment. Another coating in which the pillared clay was modified, by evacuation of a mixture of corrosion inhibitor and pillared montmorillonite, provided improved corrosion protection for higher exposure periods in the same environment. This was shown by electrochemical and weight loss measurements. However, by increasing the coating exposure time in the aggressive environment, the coating suffered deterioration. It was also proven that the coatings provided autonomous healing in case of long-time exposure.
The self-healing mechanism in corrosion mitigation may be assessed and validated by several electrochemical tools. The most common techniques reported to assess the self-healing and corrosion inhibition of such materials are scanning vibrating electrode technique (SVET), scanning ion selective electrode technique (SIET) and localized impedance spectroscopy (LEIS) [231].

Sol-gel Coatings with Anti-Fouling Function
Anti-fouling is another important function to enhance the corrosion protection of a coating. Coatings designed for this purpose are generally based on dense organic matrices, containing wide-spectrum biocides such as tributyltin and tributyltin oxide. These biocides are one of the major contaminants in marine and freshwater ecosystems [260], and nowadays their use is forbidden. Therefore, there is an emergent interest in develop new coatings with controlled release of benign biocides [141,[261][262][263][264][265][266]. The use of nanocontainers loaded with biocides is considered a very attractive methodology, since a controlled release can minimize the environmental impact.
In the last 20 years, anti-fouling coatings have been extensively studied [110,141,261,[267][268][269][270][271][272][273][274], including sol-gel coatings with anti-fouling properties [131,132,262,275]. Although many approaches and routes have been proposed [131,132,231,[262][263][264][276][277][278][279], there is still an absence of long-term and effective solutions. Generally, two corrosion mechanisms in the marine environment are considered; i.e., microbiologically influenced corrosion (MIC) and marine bio-fouling. Y. Li and C. Ning [280] published a review focused on the research progress regarding these two mechanisms. The authors concluded that MIC and bio-fouling are prevented by the control of the microorganisms' activities in biofilms, their adhesion and their formation of biofilms. It was also concluded that the performance of antifouling coatings has been improved by the modification of self-polishing copolymers and the development of degradable polymers. Conducting polymers were also developed and introduced to mitigate corrosion and biofouling.
A wide range of encapsulated agents for fouling mitigation were proposed and assessed, including enzymes [88,141,[281][282][283], ZnO 2 NPs [284], silver and benzalkonium chloride [265], zinc pyrithione [264] and chlorhexidine [275]. The encapsulation of enzymes showed auspicious results [141,[281][282][283]. For example, M. Meißler, et al. [283] reported the combination of a titanium binding peptide to a linear peptide-block-poly(ethylene glycol). The adsorption function of the peptide segments within peptide-PEG conjugates was weakened by enzymatic proteolysis. It was concluded that the adsorption properties related to the titanium substrate were fully suppressed, showing potential for antifouling surfaces in the biomedical field. Coatings combining both anti-fouling and anti-corrosion functions have also been reported [265,[285][286][287]. Arukalam et al., for instance, prepared perfluorodecyltrichlorosilane-based poly(dimethylsiloxane)-ZnO coatings for fouling and corrosion mitigation. The authors chose the ZnO NPs to study the influences of the particles' nature: the hydrophilic and anti-fouling properties. The efficacy of the produced coatings was assessed, and it was concluded that they were promising for such application. E. Wallström et al. [264] reported an auspicious route to introduce anti-fouling functionalities within a coating, wherein it was shown that the use of zinc pyrithione reduced the release rate of the biocide when compared to the release rate for the free biocide particles in demineralised water. The authors also showed that the water uptake in the paint had a major impact on the biocide release and was dependent on a number of properties, such as the binder system, pigmentation, the amount of gel and the active component included. In the end, the authors concluded that to produce formulations without the use of bio-accumulative compounds and to minimize the biocide component, it was necessary to take into account gel composition, paint formulation and water exposure. Oldani et al. [132] in 2016, reported a study where the use of OIH sol-gel coatings was promising for producing coatings for fouling mitigation. The authors combined a commercial a,v-substituted perfluoropolyether with TEOS for deposition on stainless steel substrates. It was concluded that to obtain a suitable balance between the hydrophobic properties and the film formation, the amount of polymer ranged between 70 and 80 wt.%. The OIH coatings reported showed a water contact angle (WCA) between 130 • and 140 • and good chemical resistance. M. Barletta et al. [261] developed a promising and effective "biocide-free" antifouling coating system. The proposed system involved the use of a polyester-modified, OH-rich polysiloxane that was cured through reactions with different commercially isocyanate hardeners. The hydrophilic and hydrophobic domains were introduced within the system on the curing agent using PEG-ilate alkyl and cyclohexyl substituents, respectively. It was concluded that all the samples showed improved results when compared to samples coated with a traditional paint. S. Holberg et al. [285] recently reported the synthesis of a hydrophilic, biocide-free fouling-release coating. The authors prepared coatings from commercial precursors by dispersing a polydimethyl siloxane (silicone,PDMS)-polyethyleneglycol triblock-copolymer in PDMS (PEG-PDMS-PEG). It was shown that the fouling growth in a Pseudomonas aeruginosa culture test was reduced compared to PDMS without PEG or to steel.

Coatings with Superhydrophobic Function
Micro-and nanopores in the coatings may lead to the entrance of water and aggressive species, causing coating blistering; then peeling; and subsequently, corrosion of the metallic substrates. Therefore, an interesting approach to prevent corrosion is the development of superhydrophobic surfaces. A coating shows hydrophobic properties when the WCA on a surface is above 90 • . In the case of superhydrophobic coatings, they require a WCA above 150 • and a contact angle hysteresis (CAH) lower than 10 • [288,289]. CAH is expressed as the difference between the advancing and the receding WCA of a water droplet that expands or shrinks on the surface [290]. Additionally, these coatings should show a roll-off angle lower than 10 • . According to K.K. Varanasi et al., the roll-off angle is defined as the lowest angle that a surface needs to be inclined at before the water droplet slide or rolls off it [291]. The reduction of the WCA and contact time on the superhydrophobic surfaces mitigate the interaction between the metallic substrates and the aqueous corrosive species. This behavior allows to enhance the corrosion protection of the substrates by indirectly avoiding the contact between the metallic surface and the aggressive species [292][293][294][295]. In the last few years, the literature reported on this type of coatings increased notably [60,[291][292][293][296][297][298][299]. Numerous techniques and methods have been used in the development of superhydrophobic surfaces [300][301][302], and the sol-gel process, as the versatile method that it is, was no exception [294,299,[303][304][305][306][307]. Recently, a very detailed and comprehensive review, focused on the latest developments of superhydrophobic coatings for corrosion mitigation, has been published [308]. The challenges and limitations of the synthesis of stable superhydrophobic coatings were also included and discussed. One of the main advantages of superhydrophobic coatings is that these types of materials may include other properties, such as anti-fouling [276], anti-icing [309] and bio-corrosion [231]. According to a review published by Montemor [231] in 2014, several reported encapsulation-based strategies seem to be promising; however, only a few studies were reported which validated the proposed strategies regarding the corrosion protection behavior [310][311][312]. However, important advances and developments on superhydrophobic surfaces have been achieved in the last five years [60,132,136,217,225,240,292,294,297,300,313].
OIH sol-gel coatings with superhydrophobic properties for corrosion mitigation have been reported for different substrates, such as aluminum [295,311,[314][315][316][317][318], copper [225,319], magnesium [320], mild steel [321,322] and stainless steel [323]. Generally, OIH sol-gel coatings show improved UV and thermal stability when compared to organic coatings due to the high strength of the Si-O bond. Most of the developments were for application in aluminum substrates. Lee and Hwang [314] reported the development of a superhydrophobic surface for Al/Si alloy by sol-gel process. The authors fabricated a silica gel layer from the Si content of the alloy itself without the need for treatment with high temperatures with an average WCA of 166.04 • . By removing one step (temperature treatment), the fabrication of such coatings becomes easier, lower in cost and enabling of its application in industry. The superhydrophobic properties can be obtained by different encapsulation routes. Wang et al. reported the storage of Ca(OH) 2 inside microcapsules and concluded that these show appropriate superhydrophobic performances, including regenerative ability [324]. Porous silica capsules were also reported and tested by several authors [305,310,[325][326][327][328]. These proved to be efficient in the development of superhydrophobic surfaces for diverse applications. Caldarelli et al. [225] reported the synthesis of a OIH superhydrophobic sol-gel coating for copper metallic substrates. The sandblasted copper substrates were coated with an alcoholic alumina sol followed by thermal annealing that was coated afterwards with a fluoroalkylsilane solution. The two-step coating deposition was performed using dip-coating technique. The authors obtained a superhydrophobic coating, and for a WCA of 180 • the thermal treatment should be between 200 • C and 250 • C. Zhang et al. [322], in 2016, produced superhydrophobic films to coat mild steel substrates. The authors obtained films by using a two-step route that included the electrodeposition of silica film followed by modification with a long alkyl-chained organic silane (dodecyltrimethoxysilane). It was concluded that the produced coatings showed improved corrosion resistance compared to conventional dodecyltrimethoxysilane-silanized coatings in aggressive environments.
A. Fihri et al. [188] published a review paper where the superhydrophobic coatings reported in the literature, until 2017, for steel protection, and their performances, were debated. The diverse models used to assess the wettability of a surface, and the approaches used to produce superhydrophobic coatings and their impacts on the corrosion mitigation of steel, were also revised. The authors concluded that remarkable advances in the development of superhydrophobic coatings have been achieved during the last two decades. However, most of the advances reported in the literature for the fabrication of such coatings still face many challenges for large-scale deployment. The main challenges identified were the short service life; low curing temperature and adhesion performance; low mechanical robustness; and the high costs involved. Therefore, the authors believe that due to the constraints still present in the development of such coatings, the research will progress towards overcoming these drawbacks in this field.
Superhydrophobicity, besides improving anti-fouling function, allows the encapsulation of active agents, as mentioned earlier. Therefore, the surface finishing can deliver both functionalities [231]. The sol-gel method and the use of silica particles are easy-going routes for achieving anti-fouling, anticorrosion and superhydrophobic coatings.

Challenges and Prospects for the Future Research
Nowadays, many of the effective coatings for corrosion protection represent dangers to the environment. Therefore, the key is the development of innovative materials with improved performances and promoting a sustainable environment at the same time.
The corrosion mitigation/prevention of metallic substrates is not only an engineering effort, but also a fundamental scientific difficulty. Ideally, an anticorrosion coating should be designed to be stimulus-responsive, multifunctional, resistant and durable in a wide range of applications. Coatings for corrosion mitigation are normally exposed to complex environments. Therefore, studies on how the different aggressive species (i.e., Cl − ) and water behave and react within the coating at atomic and nanoscales are needed.
The opportunity of hosting different functionalities broadens the range of applications for OIH sol-gel materials, which can be functionalized with carriers loaded with different agents. However, the development of this type of material requires multidisciplinary collaboration, including materials science, biology and polymer chemistry. Ideas for the encapsulation of anti-fouling species have been transferred from the biological and medical fields. The OIH sol-gel materials' features allow one to obtain multifunctional coatings, such as self-responsive materials with anti-fouling, anticorrosion and superhydrophobic functions within the same matrix. The existent literature clearly shows that the distinctive properties of the OIH sol-gel materials can be successfully employed for the development of coatings for corrosion mitigation of different metallic surfaces in challenging environments. However, further studies should be performed using different corrosion inhibitors and different trigger stimuli. Stability and long-term healing capacity research should also be considered in depth, since these agents should maintain their function abilities for an extended period (i.e. at least 20 years). Additionally, multi-damaging and the size of the area damaged may be a drawback for these coatings and should be further investigated. On the other hand, sustainability at a large scale, toxicity and the effects of inherent properties of OIH coatings remain only vaguely explored. Although several OIH coatings for corrosion mitigation have been subjected to intensive research, it seems that further investigations are still necessary for both fundamental and applied aspects. The synthesis of OIH multifunctional coatings (e.g., anticorrosion properties, high hydrophobicity, suitable adhesion performance, self-healing abilities) with extended service lives-highly required in order to develop commercial scale products-has not been accomplished yet.
Smart coatings with self-healing functions and stimulus-responsiveness are potentially the future of developments. Self-heling by the incorporation of responsive additives within the OIH coating materials enables, due to external stimulus (e.g., pH, the presence of Cl − , UV, temperature and/or humidity), the restoration of the material structure and recover the integrity of the protective coating. Hence, suppressing the beginning of corrosion process and increasing the service life of the metallic materials. Additionally, the incorporation of inhibitors that can mitigate and control the corrosive substances ingress will provide extra protection together with the coating structure restored. This direction in the development of smart coatings for corrosion mitigation will for certain mark the 21st century achievements.
Funding: Program Budget COMPETE-Operational Program Competitiveness and Internationalization-COMPETE 2020, and the Lisbon Regional Operational Program (its FEDER component), and by the budget of FCT Foundation for Science and Technology, I.P, grant number POCI-01-0145-FEDER-031220.

Acknowledgments:
The author acknowledges the financial support provided by the project "SolSensors-Development of Advanced Fiber Optic Sensors for Monitoring the Durability of Concrete Structures", with reference POCI-01-0145-FEDER-031220 and the support of Centro de Química, CQUM, which is financed by national funds through the FCT Foundation for Science and Technology, I.P. under the project UID/QUI/00686/2019.

Conflicts of Interest:
The author declares no conflict of interest.