Vegetable Additives in Food Packaging Polymeric Materials

Plants are the most abundant bioresources, providing valuable materials that can be used as additives in polymeric materials, such as lignocellulosic fibers, nano-cellulose, or lignin, as well as plant extracts containing bioactive phenolic and flavonoid compounds used in the healthcare, pharmaceutical, cosmetic, and nutraceutical industries. The incorporation of additives into polymeric materials improves their properties to make them suitable for multiple applications. Efforts are made to incorporate into the raw polymers various natural biobased and biodegradable additives with a low environmental fingerprint, such as by-products, biomass, plant extracts, etc. In this review we will illustrate in the first part recent examples of lignocellulosic materials, lignin, and nano-cellulose as reinforcements or fillers in various polymer matrices and in the second part various applications of plant extracts as active ingredients in food packaging materials based on polysaccharide matrices (chitosan/starch/alginate).


Introduction
Pristine polymeric materials alone often show poor physico-chemical properties. The incorporation of additives into polymeric materials improves their processability, tuning their properties to make them suitable for multiple applications like packaging, automotive, design, constructions, etc. Additivation of various compounds or nanoparticles to the virgin polymers can improve both bulk and surface properties of the products. According to the European Community an additive is "a substance which is incorporated into plastics to achieve a technical effect in the finished product, and it is intended to be an essential part of the finished article" [1].
Efforts are made to incorporate into the raw polymers various biodegradable additives with a low environmental fingerprint, such as by-products and biomass. Therefore, biobased, biodegradable polymer composites are more and more studied, as a large number of biodegradable polymers are already commercially available [2].
Composite materials exhibit advantages from the combination of multiple properties, which cannot be achieved by a monolithic material as they are systems which consist of one or more discontinuous phases enclosed in a continuous matrix [3]. The discontinuous, disperse phase, which is completely immiscible with the matrix, can be a reinforcement (reinforcing agent) or filler and the resultant composite shows optimized mechanical properties, such as strength, stiffness, and hardness [4]. As traditional plastics are resistant to biodegradation, the concept of using natural plastics (natural biodegradable polymers or biopolymers) as reinforced matrices for biocomposites is getting more and more interest.
In this review various recent applications of plant-based additives (lignocellulosic fibers/nanocellulose as well as bioactive plant extracts) as reinforcements and active ingredients in food packaging materials are illustrated. Natural polysaccharide biopolymers (such as chitosan/starch/alginate) are nontoxic, biodegradable, biocompatible, and largely used in food packaging: Chitosan is known for its broad antimicrobial activity and its excellent film-forming properties; alginates have good film-forming properties, retain moisture, reduce microbial counts, and retard oxidative off-flavors; and starch is also particularly important for its cheap price and its frequency in nature. For these reasons, this review will present applications of plant extracts as active ingredients in natural polysaccharide biopolymers: chitosan/starch/alginate.

Classification of Natural Biodegradable Polymers and Additives
Natural biodegradable polymers and additives are polymers formed naturally by the living organisms by enzyme-catalyzed reactions and reactions of chain growth from monomers which are formed inside the cells by complex metabolic processes [5].
Natural additives can be high molecular weight (natural polymers), such as proteins (collagen, silk, and keratin), carbohydrates (starch and glycogen), lignin, cellulose, high molecular weight phenolics (tannins and derivatives), and low molecular weight active substances, such as coldpressed oils, essential oils (organic volatile compounds, generally of low molecular weight, containing phenols, alcohols, ethers or oxides, aldehydes, ketones, esters, amines, amides, heterocycles, and terpenes [6]), or low molecular weight phenolics (phenolic acids and flavonoids) [7]. Natural additives are widely used materials in many applications in combination with synthetic or natural polymers. These materials, together with pomaces and biowaste, are nontoxic, less expensive than the synthetic ones, ecologically friendly, and widely available.
In Table 1, recent data regarding the applications of the most-used natural polymers and natural extracts used as components/additives in new performant materials, based on their source and type (animal/vegetable/mineral and low/high molecular weight), are summarized, together with the corresponding obtaining and mixing methods. As can be seen, the natural additives are widely used as filler and additive materials to improve the biodegradability or the mechanical properties (reinforcements) or to provide antioxidant or antibacterial activity in various synthetic or natural polymeric matrices. These natural additives are added to the polymeric matrices mainly by melt blending and solution casting. Table 1. Natural compounds (polymers and natural extracts) used as components/additives in new polymeric materials together with their methods of preparation and applications.

Source and Compound Obtaining Method Mixing Method Application Plant Sources Polysaccharides
Cellulose; used as pulp, nanocrystals, nanofibers and fibers Cellulose can be isolated using a combination of chemical and mechanical treatments like ultrasonication combined with chemical pretreatments, high shear homogenization coupled with acid hydrolysis and steam explosion, etc. [13].

Starch
Starch is extracted from seeds, roots and tubers, by wet grinding, washing, sieving and drying [19].
Mineral and animal fibers such as hair silk and fibers are not widely used as reinforcements -but plant fibers have been used widely in biocomposites field for applications in the areas of automotive, marine and construction [10].
The most interesting fibers for composite reinforcements and most commonly accepted fibers by the industry [11] are from plants, in particular bast, leaf, and wood fibers. The fibers are basically a rigid, crystalline cellulose microfibril-reinforced amorphous lignin and/or hemicelluloses matrix. As the environment is concerned, these fibers are biodegradable, light weight, relatively cheap, and are "carbon positive" since they absorb more carbon dioxide than they release. In thermoplastics they are introduced by melt mixing and in thermosets by vacuum-assisted transfer molding (VARTM) and vacuum bag resin transfer molding (RTM) [12].
In Table 1, recent data regarding the applications of the most-used natural polymers and natural extracts used as components/additives in new performant materials, based on their source and type (animal/vegetable/mineral and low/high molecular weight), are summarized, together with the corresponding obtaining and mixing methods. As can be seen, the natural additives are widely used as filler and additive materials to improve the biodegradability or the mechanical properties (reinforcements) or to provide antioxidant or antibacterial activity in various synthetic or natural polymeric matrices. These natural additives are added to the polymeric matrices mainly by melt blending and solution casting. Table 1. Natural compounds (polymers and natural extracts) used as components/additives in new polymeric materials together with their methods of preparation and applications.

Proteins
Soy Protein, hydrolyzed proteins (wheat gluten, wheat gliadin), zein, polypeptides -Alkaline extraction followed by protein precipitation at isoelectric pH; -protein extraction with salt solution, followed by precipitation from a salt extract by ultrafiltration, diafiltration membranes or dilution in cold water (micellization) [29]; and -novel techniques, such as ultrasound assisted extraction, enzyme-assisted extraction in the form of proteases and/or carbohydrolases [29].
Reinforcement in polymer composites [31,32]. Polypeptides: Reinforcement in polymer composites [33]. Food packaging applications [34] or incorporated as a reinforcement in films with enhanced barrier properties [35] (zein). Mixing different proteins with polysaccharides is an effective way to improve barrier and mechanical properties of proteinpolysaccharides films [36].

Lignins
Industrially, lignin is isolated from cellulosic fibers by chemical treatment, which breaks down lignin-carbohydrate complexes. During this process, partial depolymerization of the complex lignin macromolecules occurs along with re-polymerization (condensation) which may alter the native lignin structure [37]. The paper pulping process (lignin extraction from lignocellulosic biomass) which produces industrial lignin as a byproduct [37] may include chemical methods [38], such as -Kraft process which uses a mixture of Na 2 S and NaOH (White Liquor) at high temperature (150-180 • C), -sulfite process which employs sulfite or bisulfite to digest biomass, -organosolv pretreatment of lignocellulose which involves a biomass extraction in a mixture of solvent (ethanol being the most common) and water under high pressure [39], -single pot soda cooking pre-treatment for extracting lignin and isolate cellulose nanofibrils simultaneously [13].
Lignin as reinforcer/fillers in thermoplastic polymers improved mechanical properties, decreased water absorption, antioxidant effect due to the phenols in the lignin structure [41], improved water resistance, and thermal stability of the natural polymers such as starch or proteins. [40]. The most commonly applied methods for the extraction of polyphenols uses water in combination with organic solvents (acetone, ethanol, methanol, ethyl acetate) as per the type of polyphenols present in the plant [42].
Blending methods to circumvent the loss of the volatile compounds: -melt blending requires the addition of the active compound in a later stage of the mixing after the polymer is melted, low melting temperature and decreased mixing time [43]. -dispersion/dissolution of the polymer and all active components in a common solvent that is subsequently evaporated (solution casting technique)-method that can also be used as a coating technique by casting the dissolution onto the particular surface [43]. -novel method which involves electrospinning/electrospraying the polymer/active component solution-the advantage of faster solvent evaporation compared with the solution casting technique with the possibility to encapsulate volatile compounds into polymeric fibers/particles.

Chitin
Isolation of chitin from crustaceans, such as crayfish, crab, shrimp, and other organisms such as fungi [49], by deproteinization with alkaline treatment at high temperatures, and demineralization with dilute hydrochloric acid [50].
Chitin nanocrystals and nanofibers were added by melt-mixing as fillers into thermoplastic starch-based biocomposites [51]. Also, chitin nanofibers were added in molten PLA by extrusion [52].
Solvent blending [55,56], extrusion blending and reactive extrusion blending [57] as chitosan may be heated up to temperatures below its glass transition temperature without affecting its physicochemical properties [58].
Collagen/hyaluronic acid Hyaluronic acid it is mainly produced via streptococcal fermentation. Recently the production of hyaluronic acid via recombinant systems was studied due to the avoidance of potential toxins [49]. -Collagen can be basically obtained from the slaughter of pork and beef by chemical hydrolysis and enzymatic hydrolysis [62].
Polymer-nanoclay nanocomposites may be prepared by melt or solution blending, with partially exfoliated clays, in situ polymerization, and melt intercalation by conventional polymer extrusion process, microwave and ultrasound irradiation [66].
Nanoclays used as fillers in various polymer matrices enhancing mechanical properties of the polymer matrix [67]. In biomedical field:nanoclays as fillers in chitosan poli e-caprolactone poly-ethylene glycol poly(2-hydroxyethyl methacrylate) for drug delivery applications, as reinforcements for PMMA composites for bone cement applications or implants with improved bioactivity and mechanical properties or incorporated to polysaccharide hydrogels that can support cell proliferation (chitosan, gellan gum) [68].

Lignocellulosic Materials and Plant Extracts in Polymeric Composites (As Reinforcements/Components/Additives)
In this review, various applications of plants used as bioresources are discussed, providing valuable raw materials used as additives in polymeric matrices, such as lignocellulosic fibers [69] and nano-cellulose [70], as well as plant extracts containing bioactive phenolic compounds [42] used in the pharmaceutical and cosmetic industries [71]. The increasing environmental concerns draw attention on their use as active compounds, instead of synthetic ones.
In this review we will illustrate in the first part (Section 2.1) recent examples of lignocellulosic materials, lignin, and nano-cellulose as reinforcements or fillers in various polymer matrices, and in the second part (Section 2.2) various applications of plant extracts as active ingredients in food packaging materials based on polysaccharide matrices (chitosan/starch/alginate).

Lignocellulosic Materials, Lignin and Nano-Cellulose As Reinforcements (Additives) in Polymer Matrices
Lignocellulosic biomass, mainly composed of cellulose, hemicellulose, and lignin ( Figure 3), is the most abundant plant material and therefore is the most promising feedstock being renewable, inexpensive, biodegradable and non-toxic. Due to the environmental concerns, the development of composite polymeric materials containing lignocellulosic materials has increased and is becoming common in the polymer industry [72].  Cellulose, the most abundant biopolymer in nature, has promising uses as reinforcement of mechanical properties in polymeric bionanocomposites. Nanocellulose also has several advantages for the development of new materials: The mechanical properties and its nanometric dimensions, together with its abundance, renewability, and biodegradability, open a wide range of possible applications for biocomposites or pharmaceutical carriers [74,75].
Lignin draws attention as a valuable environmentally friendly and biodegradable raw natural resource. Lignin is the second most abundant organic substance in the world, estimated to represent 30% of the total biomass produced in the biosphere and is mostly produced by the paper pulping industry [37].

Lignocellulosic Materials
The use of natural fibers expanded due to the higher prices for petroleum products but also supported by the acceptance among consumers who encourage the use of renewable and nonpolluting raw and waste materials [12]. As reinforcements in bioplastics, lignocellulosic fibers are biodegradable, renewable, and widely available; moreover, they have low density, competitive specific mechanical properties, and a relatively low cost [76,77]. Various polyolefins, polylactic acid, Cellulose, the most abundant biopolymer in nature, has promising uses as reinforcement of mechanical properties in polymeric bionanocomposites. Nanocellulose also has several advantages for the development of new materials: The mechanical properties and its nanometric dimensions, together with its abundance, renewability, and biodegradability, open a wide range of possible applications for biocomposites or pharmaceutical carriers [74,75].
Lignin draws attention as a valuable environmentally friendly and biodegradable raw natural resource. Lignin is the second most abundant organic substance in the world, estimated to represent 30% of the total biomass produced in the biosphere and is mostly produced by the paper pulping industry [37]. The use of natural fibers expanded due to the higher prices for petroleum products but also supported by the acceptance among consumers who encourage the use of renewable and non-polluting raw and waste materials [12]. As reinforcements in bioplastics, lignocellulosic fibers are biodegradable, renewable, and widely available; moreover, they have low density, competitive specific mechanical properties, and a relatively low cost [76,77]. Various polyolefins, polylactic acid, and PVA have recently been reinforced using cellulosic fibers from by-products from the production process in industry.
For example, some authors have tested composite formulations with mechanical and physical properties improved compared with the neat polymer and with the advantage of a higher bio-based content [78]. Thus, polypropylene composites containing dried distillers' grains (DDG-10, 2.4, and 2.2 wt %), a coproduct of corn ethanol industries, maleated polypropylene, and maleated ethylene-propylene diene monomer rubber as compatibilizers, had improved strength and modulus compared with the neat polypropylene. The DDG with irregular shapes, mostly in the form of flakes-the majority of the particles were between 0.25 and 2 mm in their smallest dimension -was used in the as-received form with no surface modification or size reduction treatment. [78].
It is known from many reported papers that incorporation of natural fibers from approximately 20 to 35 wt % in polymer composites is the most appropriate amount to achieve optimum technical and economic benefits and addition of more fiber does not lead to any significant enhancement in the mechanical properties of the fiber composites [79,80].
Thus, Yerba mate (Ilex paraguariensis) fibers (20, 30 and 40 wt %) were used as reinforcing filler in polypropylene composites in order to increase the mechanical properties of the composites. The residue, ground and sieved to obtain a fibrillar structure with diameters above 100 µm, was processed into PP in a single-screw extruder, then ground in a knife mill, oven dried, and reprocessed in a twin-screw extruder [81]. The study revealed that the tensile strength at break was highest for 30% yerba mate but with further reduction for higher amounts of Yerba mate fiber. The addition of the filler also introduced regions of poor interfacial adhesion and stress concentration in the composite due to the imperfection in filler dispersion (agglomeration) [81], which explains the lower flexural strength of the composites and a gradual reduction of the impact resistance with the increase of the Yerba mate fiber content. Similar results have been obtained by other authors: High density polyethylene composites filled with three kinds of shell fibers (peanut shell, rice husk nor walnut shell −30-70 wt %), [82] increased the creep resistance and decreased the impact strength of the three composites for all compositions studied [82], while the bending and tensile strength increased first with the fiber content, and then decreased [82].
The mechanical properties (tensile strength, Young's modulus, flexural strength, and flexural modulus) of polylactic acid (PLA) composites reinforced with hybrid sisal and hemp fiber (30 wt %) were improved compared to neat PLA [83]. The dried hemp and sisal fiber (a by-product from the production process in industry, where the leaves of the plant are predominantly used) [79] were aligned and granulated into 4 mm lengths and further processed/blended through extrusion and injection molding [83]. Thus, it is possible to replace 30%-40% by mass of the matrix with fibers (a by-product from the production process in industry, where the leaves of the plant are predominantly used) [81].

Lignin
Lignin, a natural polyphenol [38], is a major component of all plants and an enormous renewable material and is mainly produced as a side-product by the bioethanol and the paper industry during the cellulose extraction [38].
As a thermoplastic polymer with high-impact strength and heat-resistance, lignin can be compounded within a polymer matrix, enhancing the mechanical properties due to the relatively high rigidity of the 3D network structure of the lignin molecules [40]. Blending lignin with other biopolymer or synthetic polymer materials has been attractive because of its wide availability, good mechanical properties, and biodegradability, along with the diversity of potential modifications due Polymers 2020, 12, 28 9 of 34 to its chemical structure [84]. For example, solution-casted lignin-modified PVC membranes had improved hydrophilic and anti-fouling properties together with improved stability and durability after a 6-cycle oily wastewater treatment of PVC membranes [85].
Lignin is generally described as a highly cross-linked co-polymer containing phenyl-propanoid units linked together through a variety of C-C and C-O bonds, resulting in the presence of aliphatic hydroxyl and phenolic hydroxyl groups ( Figure 4) [86]. Due to its numerous hydroxyl groups, the lignin molecule is relatively polar and generally presents poor compatibility with nonpolar polymers, such as polyolefins and polystyrene (or aromatic polymers) [38]. Lignin can enter only into weak dispersion interactions; thus, in the lignin/polyolefin systems limited compatibility is expected [38], which may be improved by using compatibilizers, reactive compatibilization [40], chemically modified lignin, or by adding a coupling agent [38]. Due to the strong self-interactions, lignin forms immiscible blends (0-60 vol % lignin) with ethylene-vinyl alcohol (EVOH) copolymers (0-76 mol % vinyl alcohol) as lignin was dispersed in the form of particles in the EVOH phase even at lignin contents as large as 60 vol %, in spite of the hydrogen bonds acting between the two components. Additionally, as the equilibrium thermodynamic factors are stronger than kinetic ones in the studied system, changing shear stresses during the melt (220 • C) blending process did not influence particle size much [87].
composites filled with three kinds of shell fibers (peanut shell, rice husk nor walnut shell −30-70 wt %), [82] increased the creep resistance and decreased the impact strength of the three composites for all compositions studied [82], while the bending and tensile strength increased first with the fiber content, and then decreased [82].
The mechanical properties (tensile strength, Young's modulus, flexural strength, and flexural modulus) of polylactic acid (PLA) composites reinforced with hybrid sisal and hemp fiber (30 wt %) were improved compared to neat PLA [83]. The dried hemp and sisal fiber (a by-product from the production process in industry, where the leaves of the plant are predominantly used) [79] were aligned and granulated into 4 mm lengths and further processed/blended through extrusion and injection molding [83]. Thus, it is possible to replace 30%-40% by mass of the matrix with fibers (a by-product from the production process in industry, where the leaves of the plant are predominantly used) [81].

Lignin
Lignin, a natural polyphenol [38], is a major component of all plants and an enormous renewable material and is mainly produced as a side-product by the bioethanol and the paper industry during the cellulose extraction [38].
As a thermoplastic polymer with high-impact strength and heat-resistance, lignin can be compounded within a polymer matrix, enhancing the mechanical properties due to the relatively high rigidity of the 3D network structure of the lignin molecules [40]. Blending lignin with other biopolymer or synthetic polymer materials has been attractive because of its wide availability, good mechanical properties, and biodegradability, along with the diversity of potential modifications due to its chemical structure [84]. For example, solution-casted lignin-modified PVC membranes had improved hydrophilic and anti-fouling properties together with improved stability and durability after a 6-cycle oily wastewater treatment of PVC membranes [85]. Lignin is generally described as a highly cross-linked co-polymer containing phenyl-propanoid units linked together through a variety of C-C and C-O bonds, resulting in the presence of aliphatic hydroxyl and phenolic hydroxyl groups ( Figure 4) [86]. Due to its numerous hydroxyl groups, the The hydroxyl content influences the compatibility between lignin and polyolefins: The less aliphatic hydroxyl content (0.4 mol/kg) of de-polymerized hydrolysis lignin (DHL) promotes better dispersion in polyethylene (PE) compared with de-polymerized kraft lignin (DKL) (0.7 mol/kg) [88].
Many studies have focused on the incorporation of lignin into natural biopolymers, such as starch, protein, cellulose, PLA, and PHB, to form bioplastics [89]. For example, the properties of the starch/lignin bio-nanocomposites, such as water uptake, water swelling, hydrolytic degradation, water vapor permeability, mechanical, and thermal properties, were enhanced significantly due to the lignin addition [90]. Lignin caused the rougher surface of the starch film, modified some structural properties, and improved thermal properties [91]. The addition of alkali lignin (AL) as a filler into the soy protein isolate (SPI) films increased the UV light absorption, improved tensile strength (TS) and thermal stability, as well as decreased the water vapor permeability of the films [92].
In addition, lignin plays an important part in antioxidant properties as a stabilizer because the phenolic hydroxyl groups can scavenge free radicals [93]. The antioxidant behavior of lignin stems from its inherent hindered phenolic structure, which facilitates lignin to work as a free radical scavenger [94]. For example, addition of 2.5 wt % of de-polymerized kraft lignin (DKL) or 5 wt % of de-polymerized hydrolysis lignin (DHL) to polyethylene (PE) attained the same level of antioxidant activity as the addition of 0.5 wt % of Irganox 1010 (a phenolic antioxidant-pentaerythritol tetrakis(3-(3,5-di-tert-butyl-4-hydroxyphenyl)propionate). The lower antioxidant activity compared to the commercial antioxidant, caused by the lower phenolic concentration, complex molecular feature, and higher hydrophilicity of the de-polymerized lignins, can be compensated for by the lower price of the de-polymerized lignins [88].

Nanocellulose
Nanocellulose fibrils, which are the building blocks of plant cell [95] walls and give plants and trees their structural strength and stiffness, are a very interesting and well-studied nanoscale natural material that can potentially improve the properties of the polymers [96]. Many studies have already reported on use of nanocellulose in different forms for composite applications [70]. Cellulose nanomaterials are considered as a suitable solution to replace commonly used inorganic nanofillers [97] because they are widely available, renewable, and biodegradable [96]. Moreover, they possess unique valuable characteristics, such as a high specific strength, moduli , and specific surface area. Composites with nanocellulose nanoscale reinforcements have been proposed [98].
Regarding the nanocellulose, there some particularities compared with other artificial nanoparticles: In the case of carbon nanoparticles or nanoclays, the mechanical constraining of polymer chains [99], and surface/polymer interaction (with formation of layer of perturbed macromolecules around nanoparticles [100]) are supposed to be responsible for the beneficial effect of nanoparticles on the mechanical properties. In the case of nanocellulose, different mechanisms allow the nanocellulose to influence and enhance the polymer properties [101], i.e., the formation of a network of long nanoscale fibers [101]; the interaction between nanoparticles/nanofibrils, which is controlled not only by Van der Waals forces but also by strong hydrogen bonds [102,103]; and also the adhesion to the polymer matrix, which is dominated by hydrogen bonding [104,105]. Different to carbon nanoparticles, nanocellulose fibrils do not form clusters but percolation networks [106], which have a positive effect on the strength of the composites [107].
Cellulose nanofibers are characterized by a short-rod-like shape less than 100 nm in diameter and several micrometers in length with ordered regions (Figure 5), induced by the linear nature of the cellulose polymers and the extensive intermolecular attractions between adjacent chains [108]. Cellulose nanofibers can be extracted from different natural sources [109] (wood or non-woody plants [110]), by mechanical treatment [111], acid hydrolysis (the most-used method) [112], or a combination of the two [113]. Acid hydrolysis can be assisted by ultrasonic treatment (sonication) [114,115] and enzymatic hydrolysis [116].
Polymers 2020, 12, 28 11 of 36 carbon nanoparticles, nanocellulose fibrils do not form clusters but percolation networks [106], which have a positive effect on the strength of the composites [107]. Cellulose nanofibers are characterized by a short-rod-like shape less than 100 nm in diameter and several micrometers in length with ordered regions (Figure 5), induced by the linear nature of the cellulose polymers and the extensive intermolecular attractions between adjacent chains [108]. Cellulose nanofibers can be extracted from different natural sources [109] (wood or non-woody plants [110]), by mechanical treatment [111], acid hydrolysis (the most-used method) [112], or a combination of the two [113]. Acid hydrolysis can be assisted by ultrasonic treatment (sonication) [114,115] and enzymatic hydrolysis [116]. Acid hydrolysis is an easy and fast method to produce nanocellulose. A strong acid such as H2SO4 or HCl is commonly used to break the glycoside bonds in cellulose under controlled conditions (acid concentration, time, temperature, and acid/cellulose ratio) [117], a process which is stopped by dilution with water followed by washing/dialysis to remove free acid molecules and drying of the suspension to yield solid nano-cellulose [112]. Acid hydrolysis leads to agglomerated cellulose in the micrometer scale, which can be reduced to nanofibers in the nm scale by high pressure homogenization [118] due to the shear forces caused by the high velocity and pressure on the micro- Acid hydrolysis is an easy and fast method to produce nanocellulose. A strong acid such as H2SO4 or HCl is commonly used to break the glycoside bonds in cellulose under controlled conditions (acid concentration, time, temperature, and acid/cellulose ratio) [117], a process which is stopped by dilution with water followed by washing/dialysis to remove free acid molecules and drying of the suspension to yield solid nano-cellulose [112]. Acid hydrolysis leads to agglomerated cellulose in the micrometer scale, which can be reduced to nanofibers in the nm scale by high pressure homogenization [118] due to the shear forces caused by the high velocity and pressure on the micro-suspension of cellulose nanofibers [119,120]. Using this procedure and high pressure homogenization, ginger cellulose nanofibers (GNF) (100-200 nm width and 2-3.5 µm length) were isolated and used (1% to 7% GNF) in bionanocomposites prepared by the solvent cast method in order to reinforce chitosan (CS) and polyvinyl alcohol (PVA). The best GNF content was 5% in terms of mechanical properties [120] due to the formation of hydrogen bonds between GNF and both CS and PVA. As CS has antibacterial activities over a wide range of bacteria [121] the chitosan containing GNF film had a higher inhibitory effect against Bacillus cereus, Escherichia coli, Staphylococcus aureus, and Salmonella typhimurium [120] because the bacterial cell wall can adhere to CS by electrostatic interaction [122], thereby changing the structure and permeability of the bacterial cell membrane [122].
Cellulose nanocrystals (CNC) were also successfully isolated from waste cotton cloth fibers using a mixed acid hydrolysis of the extracted cellulose (H2SO4 (98 wt %), HCl (37 wt %), and deionized water solution at a volume ratio of 3:1:11.) and subsequently used as fillers to reinforce a polylactic acid (PLA) matrix (0-0.7 wt % CNC) [123]. The PLA/CNC solvent cast films showed high crystallinity, tensile strength, and elasticity modulus at 0.1% and 0.3% CNC content [123]. However, at higher CNC content (0.7%), the CNCs were not well distributed in the polymer matrix, leading to minimal light transmittance, crystallization, tensile strength, elasticity modulus, and elongation at break [123]. Furthermore, the elongation at break of PLA/CNC composite films decreased with the increase in CNC content due to the restricted mobility of polymer macromolecules due to the increased film stiffness [123]. A significant decrease in light transmittance (from 67% to 53% at λ = 800 nm) was observed for PLA/CNC composite films when the CNC content increased from 0.1% to 0.7% [123]. The surface structure of the PLA/CNC composite films became increasingly compact with the higher CNC content [123] while considerable particle aggregation was observed on the surface of the composite film with the highest CNC content due to the hydrogen bond formation [123].
For effective use of cellulose fibers, good dispersion and adhesion between the fiber surface and resin are essential [124]. However, the OH groups on the surface of cellulose fibers make them highly hydrophilic [125,126], while most polymer resins are hydrophobic, which leads to poor dispersion and adhesion. Furthermore, the OH groups from nanocellulose result in strong hydrogen bonding leading to agglomeration of these fibrils during the drying process [127], making them difficult to re-disperse these fibrils even in water [128]. To address this, some authors followed a new approach in which chopped, loosely packed (i.e., low density) freeze-dried cellulose nanofibrils (CNF) networks (foams, i.e., bundles of CNFs) were used as "microsponges" that polymer resins can penetrate during melt processing, creating mechanical interlocking by hydrogen bonding among CNFs as a reinforcing mechanism, provided that the low packing density was achieved [124]. The dried PLA/CNF composites were mixed in chloroform and fed to a high-shear mixer and finally compression molded [124]. The use of CNFs (10-40 wt %) increased the tensile strength (up to 80%), elastic modulus (up to 200%), strain at break (75%), and toughness (220%) compared to the neat PLA resin [124]. Similar improvements in tensile strength and elastic modulus were observed when the PLA/CNF composite was tested as material for 3D-printing, although strain at break and toughness values dropped [124]. Still, the shear forces in the 3D-printing process [129] resulted in orientation and stretching of these CNF bundles in the printing direction, leading to further increases in stiffness and storage modulus. In other words, beneficial controlled directional stiffening of the manufactured parts can be attained with the printing process [124].
The polymer nanocomposites are traditionally constructed utilizing one nanomaterial as a filler [130]. There is also a possibility to tune the mechanical properties through the introduction of a second nanofiller (for example carbon nanotubes together with montmorillonites [131]). Tricomponent materials containing poly(vinyl alcohol) (PVA) and cellulose nanocrystals (CNC)/chitin nanofibers (ChNF) as filler (total filler content 5 wt %) [132] showed an overall increase in stiffness, tensile strength, and thermal stability [132]. Furthermore, CNC /ChNF mixtures at certain ratios were able to more effectively reinforce PVA better than CNC or ChNF alone [132]. Results showed certain ratios between cellulose and chitin had the largest moduli and tensile strength. The authors suggested this is the result of chitin nanofibers binding to themselves through hydrogen bonding and also creating a high strength network with the CNC [132]. The authors also suggested that above certain CNC loadings (1 wt %) agglomeration occurs between particles which generates weak points in the material, which could explain the relative decrease in mechanical properties with loadings higher than 1 wt % [132,133].
The mechanical behavior of the gelatin scaffolding material used in tissue regeneration can be improved by reinforcing it with TEMPO-oxidized cellulose nanofibrils and subsequent cross-linking [134]. By dehydrothermal crosslinking (with formation of zero-length cross-linking without any bridging molecule), both intra-and inter-molecular peptide bonds within gelatin and amidic bonds between gelatin and cellulose nanofibers were formed, which increased the mechanical stability of the scaffold. The crosslinking also decreased the degradation rate by hydrolysis [135] during the healing process in order to allow the replacement of the scaffold with newly formed tissue [136].
Not only the mechanical properties but also the barrier properties and water solubility can be improved by addition of cellulosic nanofibers (CNF) [137]. Starch naturally has poor moisture resistance [138], so the addition of CNFs is an effective way to reduce its moisture absorption, moisture sensitivity, and to improve the mechanical strength and stability of starch [137]. Due to the highly crystalline and hydrophobic character of cellulose in comparison to the starch molecule, CNFs are less hydrophilic than starch, making them effective to improve the barrier properties by reducing water vapor permeability [137]. The addition of CNFs introduced a tortuous path for water molecules to pass through [137]. However, additional amounts of CNFs might agglomerate and form a heterogeneous film, which in turn facilitates the water vapor permeation and holes in the film [137]. Cassava starch filled with chitosan/glycerol/gallic acid/CNFs (0.15, 0.5, 0.1, 0-0.1 g/g starch respectively) were prepared by a subcritical fluid system, which promotes both hydrolysis and cross-linking reactions between chitosan and starch to form a strong network [139]. The addition of CNFs reduced the film solubility in water significantly due to strong interactions between starch [140] and chitosan chains [141] with cellulose through hydrogen bonds in the film matrix [137]. This affinity or compatibility between CNFs and the starch matrix can be attributed to the chemical similarities of starch and cellulose, the nanoscale of the fibers, and the hydrogen bonds between CNFs and starch [137]. Due to the formation of hydrogen bonds between starch, chitosan, and CNFs, the gallic acid and chitosan addition to the CNF/starch also decreased the number of active −OH groups in starch and cellulose that promotes water absorption reducing the film water activity [137]. Because the addition of CNFs decreased the mobility of the starch and chitosan chains, the tensile strength increased, and elongation decreased considerably in CNF-reinforced films compared to cassava starch/chitosan/gallic acid film without CNF. Due to the cross-linking (by ester and electrostatic interactions) the addition of gallic acid and chitosan increased the tensile strength and decreased the elongation [137]. Moreover, due to the aggregation that occurred in films with 15 and 20 wt % of CNFs, the tensile strength did not increase above 17 MPa [137]. Table 2 summarizes the most recent examples of natural additives in polymers used as antioxidants, antibacterials, plasticizers, or used to increase degradability and thermal insulation. Besides lignin, natural fibers, plant extracts, and cellulose nanocrystals are presented, as well as other natural additives, such as chitosan, essential oils, and alginate. Chitosan (wt % 0-40).
The mix was melt-compounded in an internal mixer at 150 • C.
Chitosan addition increased Young's modulus evidencing a good CS-PVC interaction. Chitosan addition had no negative impact on thermal stability of the PVC composites which allows for possibility of producing composites by with thermo-mechanical processes, without risk of thermal decomposition. [59] Biodegradable polymer fiber nets of poly (lactic acid) (PLA)/poly (butylene adipateco-terephthalate) (PBAT) (60:40). Packaging material for fruit and vegetables preservation.
With essential oil addition increased plasticity (at 10% Pine EO), elongation at break and decreased Young's modulus. When chitosan was added as a coating, stiffening of the fiber was observed. [142] PLA-based composites for the packaging industry.
Water-soluble extracts acted as a plasticizer on PLA (Tg decrease) and has slightly positive influence on its stiffness in the glassy state, whereas the drawability remained fairly acceptable when PLA-based materials where drawn at 75 • C above Tg. [143] Antimicrobial PLA films for food packaging with low silver release.
Solvent casting PLA matrix acted as a diffusion barrier so that the released silver in water after 10 days was within the prescribed limit of 0.05 mg kg −1 while the films induced inhibitory effects against Staphylococcus aureus. [144] Poly caprolactone (PCL) nano fibrous mat with antioxidant activity for antimicrobial wound dressings.

Extract of medicinal plant Clerodendrum phlomidis. Electrospinning
The plant extract conferred antibacterial activity and increased in wettability of the PCL fibers without affecting their mechanical properties. [145] Polyethylene oxide (PEO) These results will recommend these films a potential candidate in electrochemical and photoelectrical devices. PLA plasticized by cardanol derivatives showed lower modulus than PEG plasticized PLA. The tensile modulus of plasticized PLA was correlated to the evolution of glass transition temperature and degree of crystallinity. At low plasticizers content, the modulus of PLA decreased as the glass transition temperature decreased, due to a better miscibility of the plasticizer with PLA. The opposite occurred at high plasticizer content; in this case, the higher modulus found for more compatible plasticizers were attributed to an increased crystallization kinetic. [147] PU polyurethane 3D-printed foams as thermal insulation, sound absorption or as damping materials.
The TPU powder was mixed with cork powder (1%, 3%, and 5% wt/wt) in the Retsch cross beater mill SK1 without sieves. Afterwards, the mixtures were left over night in an oven at 105 • C to remove moisture. The mixtures were then extruded in a Felfil Evo Colours extruder using 4 rpm at 210 • C to produce the 3D printable filaments.
3D-printed PU polyurethane composite foams for thermal applications with enhanced mechanical properties. Due to the presence of cork as well as to the presence of voids the resulting foams presented lower density, lower thermal conductivity and proved to be more flexible. The stiffness of the ensuing composites was also reduced but the elastomeric behavior of the 3D-printed foams produced may find applications that combine thermal insulation with damping properties. Yet, the use of cork did not affect the thermal stability of the composites. Cork is a well-known low thermal conductive material, which can further reduce the thermal conductivity of PU foams Besides their thermal insulation properties, their elastomeric behavior suggests that the 3D-printed foams produced may be used as thermal insulation, sound absorption or as damping materials. [148] Polyethylene/poly (lactic acid)/Degradable polymeric films Chitosan (15 wt %) with and without poly (ethylene-g-maleic anhydride) (PEgMA) as compatibilizer.
Laboratory mixer-extruder. 145 • C and 155 • C for the screw barrel.
Polyethylene/poly (lactic acid)/chitosan films, with and without poly (ethylene-g-maleic anhydride) (PEgMA) as compatibilizer, were prepared by extrusion. It was demonstrated that blends of synthetic and natural polymers have a higher susceptibility to degradation in comparison to neat polyethylene and poly (lactic acid) films. Additionally, it is found that the incorporation of PEgMA into the extruded films apparently favored the polymer degradation, as it deduced from the fall of the mechanical properties when the films are exposed to accelerated weathering simulation. [149]

Plant Extracts as Active Ingredients in Food Packaging Materials Based on Polysaccharide Matrices (Chitosan/Starch/Alginate)
The need for better preservation of perishable food products, such as fruits, vegetables, or meat, has raised new postharvest preservation technologies, such as edible coatings, coating the solid package by electrospinning, UV irradiation, modified atmosphere packaging, and ozonation [150,151]. Edible coatings-a thin layer formed on the food surface to extend its shelf life-can preserve the properties and functionality of foods as they are easy to apply by spraying or immersion (Figure 6), and can be prepared with environmentally friendly materials [152]. There is great interest in biodegradable active composite packaging materials that release substances for the purpose of extending shelf life, by incorporation of active substances, such as antioxidants, antimicrobials, and antifungals, and which can enhance barrier, thermal, and mechanical properties [153]. Herbs, spices, agricultural waste as extracts, essential or cold-pressed oils contain bioactive compounds as thymol, carvacrol, tocopherols, benzoic acids, simple or functionalized phenolics and flavonoids, lignans, etc., which confer onto them activities and nutritional values. Representative examples of their structures can be found in References [154,155].
The mechanical and antibacterial properties of chitosan edible films were improved after the incorporation of gelatin and natural cinnamon essential oil [156]. Cassava starch food packaging films with antioxidant, UV-vis light barrier and pH-sensitive properties, increased water vapor permeability, and tensile strength were also obtained by addition of anthocyanin-rich bayberry extract (1 wt %) due to the hydrogen-binding interactions between BBE and starch [157]. Similarly, the incorporation of hydrolyzed cottonseed proteins into alginate films increased the thickness and water vapor permeability, the barrier properties to visible light, and the total phenolic content and the antioxidant activity with inhibitory effect against Staphylococcus aureus, Colletotrichum gloeosporioides and Rhizopus oligosporus [158].
Electrospun antibacterial and antifungal coatings form the base solid package: Antibacterial and antifungal active elements can be incorporated in chitosan matrices by electrospinning [159], for example, antibacterial polylactic acid/AgNPs/vitamin E nanofibers presented antioxidant activity during tests on fresh apple and apple juice due to reduced polyphenol oxidase activity, which make this materials a potential preservative packaging for fruits and juices [160]. The electrospun nanofibers containing low amounts of bioactive substances can be coated onto various substrates [161,162]. For example, polylactic acid (PLA) films coated by coaxial electrospinning with clove and argan oils and encapsulated into chitosan had higher antibacterial and antioxidant activity when clove oil and high molecular weight chitosan where used [163]. Polyethylene films coated with chitosan by electrospinning had good antimicrobial activity against Gram-positive (Listeria monocytogenes) or Gram-negative (Escherichia coli, Salmonella typhymurium) bacteria and the addition of vitamin E to the coatings improved the aspect, smell, pH, and total number of germs for minced poultry meat packaging [164,165].

Chitosan/Starch/Alginate Containing Plant Extracts as Edible Food Packaging
Edible food packaging and coating materials are renewable and easily degradable that can enhance the shelf life of whole as well as fresh-cut fruits and vegetables by retarding physiological processes, such as respiration, degradation of cell walls, and transpiration, and also restrict microbial action [166]. They are generally obtained from polysaccharides such as starch, alginate, and chitosan [167]. There is great interest in biodegradable active composite packaging materials that release substances for the purpose of extending shelf life, by incorporation of active substances, such as antioxidants, antimicrobials, and antifungals, and which can enhance barrier, thermal, and mechanical properties [153]. Herbs, spices, agricultural waste as extracts, essential or cold-pressed oils contain bioactive compounds as thymol, carvacrol, tocopherols, benzoic acids, simple or functionalized phenolics and flavonoids, lignans, etc., which confer onto them activities and nutritional values. Representative examples of their structures can be found in References [154,155].
The mechanical and antibacterial properties of chitosan edible films were improved after the incorporation of gelatin and natural cinnamon essential oil [156]. Cassava starch food packaging films with antioxidant, UV-vis light barrier and pH-sensitive properties, increased water vapor permeability, and tensile strength were also obtained by addition of anthocyanin-rich bayberry extract (1 wt %) due to the hydrogen-binding interactions between BBE and starch [157]. Similarly, the incorporation of hydrolyzed cottonseed proteins into alginate films increased the thickness and water vapor permeability, the barrier properties to visible light, and the total phenolic content and the antioxidant activity with inhibitory effect against Staphylococcus aureus, Colletotrichum gloeosporioides and Rhizopus oligosporus [158].
Electrospun antibacterial and antifungal coatings form the base solid package: Antibacterial and antifungal active elements can be incorporated in chitosan matrices by electrospinning [159], for example, antibacterial polylactic acid/AgNPs/vitamin E nanofibers presented antioxidant activity during tests on fresh apple and apple juice due to reduced polyphenol oxidase activity, which make this materials a potential preservative packaging for fruits and juices [160]. The electrospun nanofibers containing low amounts of bioactive substances can be coated onto various substrates [161,162]. For example, polylactic acid (PLA) films coated by coaxial electrospinning with clove and argan oils and encapsulated into chitosan had higher antibacterial and antioxidant activity when clove oil and high molecular weight chitosan where used [163]. Polyethylene films coated with chitosan by electrospinning had good antimicrobial activity against Gram-positive (Listeria monocytogenes) or Gram-negative (Escherichia coli, Salmonella typhymurium) bacteria and the addition of vitamin E to the coatings improved the aspect, smell, pH, and total number of germs for minced poultry meat packaging [164,165].

Chitosan/Starch/Alginate Containing Plant Extracts as Edible Food Packaging
Edible food packaging and coating materials are renewable and easily degradable that can enhance the shelf life of whole as well as fresh-cut fruits and vegetables by retarding physiological processes, such as respiration, degradation of cell walls, and transpiration, and also restrict microbial action [166]. They are generally obtained from polysaccharides such as starch, alginate, and chitosan [167].
Starch is the most abundant and commonly used renewable, biodegradable natural resource, with recognized flexibility, transparency, and film-forming ability, but with low mechanical and barrier properties that are usually improved by mixing the starch with other polymers (e.g., chitosan) [168]. For example, previous studies have reported that the chitosan-starch blends exhibited an improved barrier and mechanical properties as well as good antimicrobial effect [169,170]. Alginate is a naturally occurring polysaccharide can be used in coating for extending the shelf-life of fruit, vegetable, meat, poultry, and film preparation [171]. Chitosan is a good candidate for food packing material because of its film-forming ability, biodegradability, and satisfactory mechanical strength [172].
Alginate, starch, and chitosan are materials of choice for matrices used in a wide range of applications like pharmaceutics and medicine, active food packaging, and agriculture, to develop an environmentally friendly slow or controlled release systems for drugs, bioactive compounds, and respectively pesticides entrapment/encapsulation, and so on. This is because they alone or in binary and ternary combinations of them, or with other polymers, accomplish the main requirements necessary in these fields. They have a hydrophilic nature, are biocompatible, biodegradable, highly versatile, form non-toxic matrices for the protection of active ingredients (especially probiotic microorganisms and cells sensitive to heat, pH, dissolved oxygen) among other factors in which food is exposed to during processing and storage, offer economics and safety of processing methods, etc. These polymers are also presented as tasteless and odorless food additives. Chitosan and alginate exhibit mucoadhesion, immunogenicity, thickening properties, and the ability to form gels in the presence of multivalent ions, and are very good coating materials and show properties which allow their processing by simple one-stage processes (as the external gelation technique.). They are preferable for use in microparticles production for medicines [173,174] and pharmacy [175].
Microencapsulation is widely studied to protect microorganisms from acid environments, bile salts, and oxygen. This helps to maintain the microorganism's viability during the product shelf life, which is a one of the major challenges to the food industry, since certain cultures are extremely sensitive to environmental factors such as acid and oxygen. Both maize starch and chitosan provided better protection of probiotics after exposure of the moist microparticles to simulated gastric and intestinal juice [176], demonstrating that a combination of alginate with starch improves the efficiency of different bacterial cells, particularly lactic acid-producing bacteria, due to the production of granules of good prebiotic structure and effect in the microcapsules.
A starch-chitosan-calcium alginate system showed the highest entrapment efficiency, drug/pesticide loading, and the slowest release rate, as well as an obvious slower degradation rate in soils than the commercially available formulation. [177,178]. The leaching of pesticides during the preparation of alginate beads has been improved by synthesizing bi-polymeric beads of alginate with other natural polysaccharides. An herbicide was encapsulated in chitosan and starch modified by cross-linking with alginate. The use of alginate helps bead formation and strengthens the structure of the matrices of the herbicide that was encapsulated in starch and chitosan beads reinforced with alginate. The addition of alginate improved matrix strength and prevented leakage of the encapsulated herbicide. [179].
Edible coatings could also be enriched with natural additives, such as antioxidant antibrowning [180] and antimicrobial agents, which in turn enhance the performance of the native edible coating material [181] as antioxidant activity, respiration rate, total phenolic retention, retention of ascorbic acid (AA), UV protection, etc.
The low antioxidant ability of chitosan [182] is usually improved by mixing chitosan with high antioxidant natural extracts (for example, tomato plant extract [183,184], leaf and seed extracts of Pistacia terebinthus [185], Ficus hirta fruits extract [186], flax seed mucilage extract [187], and Laurus nobilis extract [188]). Alginate and chitosan coatings containing olive leave extract were also found to improve the TP content and antioxidant activity of Sweet Cherries (Prunus avium L.). Alginate coatings containing Fircus hirta fruit extract enhanced the antioxidant activity and TP content in mandarin [189], and an edible coating from green tea extract and chitosan preserved the quality of strawberry (Fragaria vesca L.). Pomegranate peel extract (PPE) incorporated in chitosan had better retention of total phenol (TP), flavonoid content, antioxidant activity in terms of DPPH, and ripening index compared with pure chitosan, and also better than the corresponding alginate-based samples [190]. Similarly, blueberries coated with chitosan/ blueberry leaf extract (BLE) had higher TP than those coated with chitosan alone [191].
Respiration rate: One important function of edible films is to act as gas barriers and to create a biodegradable semi-permeable barrier protection and an internal modified atmosphere during the storage [192]. The application of various coating treatments could delay the rise in the respiration rate of the samples by causing changes in CO 2 production and utilization of O 2 [190]. A similar effect on retarding the respiration rate was found for mandarins coated with alginate containing Fircus hirta fruit extract [189] and avocado coated with chitosan containing moringa extract [193]. This impact of plant extracts was attributed to their antimicrobial activity that enhanced the barrier properties of the coating and restricted the gas diffusion [190] as other authors found similar effects for chitosan coatings incorporating natamycin or nisin, i.e., reduced the O 2 consumption of the fruit, delayed changes of pH, and lower CO 2 production during the storage compared to fruits coated with pure chitosan [194].
Total phenolic retention: Under oxidative stress, the total phenolic (TP) levels tend to decrease during storage period [195,196] and in the uncoated samples may be attributed to the higher respiration rate resulting in the breakdown of total phenols [197]. To slow down the deterioration events, such as respiration and moisture loss, ready-to-eat products should be protected with an edible film that modifies the internal atmosphere, resulting in slowing down the metabolism in fresh product [198].
Coating treatments could delay the declining of the total phenolic content, flavonoids, and anthocyanins content and antioxidant activity in various fruits as was found for strawberries coated with alginate containing carvacrol and methyl cinnamate (natural antimicrobials) [199], walnut kernel coated with sodium alginate coating containing pomegranate peel extract [200], and strawberries coated with chitosan containing peony extracts [201].
Retention of ascorbic acid (AA): Ascorbic acid prevents the oxidative damage in fruits and vegetables by scavenging the free radicals of the hydroxyl group, superoxide anion, and hydrogen peroxide through the ascorbate peroxidase reaction [202]. The ascorbic acid in fruits decreases continuously during the storage time [203]. In this respect, chitosan and alginate coatings enriched with PPE could retard the oxidation process in guava by maintaining higher levels of AA than the control during storage and, thereby, prevented ageing and resulting in lower oxygen permeability followed by reduction in the enzyme activity and, thereby, resulting in the reduction of AA oxidation [190].
UV protection: Food products are sensitive to various light wavelengths. Protection against light is an important and critical property of food packaging material, since light can accelerate food degradation and oxidation, resulting in nutrients and bioactive compounds destruction, forming off odors and flavors, food color loss, as well as the formation of toxic substances degradation and oxidation reactions [204].
Chitosan-plant extract films could effectively protect food against UV/visible radiation, for example, transmittance of chitosan-black soybean seed coat extract (BSSCE) was nearly in the 200-320 nm interval [205] and chitosan films containing aqueous hibiscus extract (HAE) exhibited transmittance below 10% in the 200-600 nm range [204], which was explained by the presence of several compounds in the plant extract, such as flavonoids, anthocyanin, phenolic acids, etc., which contains double bonds and could absorbs in UV/visible radiation [206].

Phenols from Plant Extracts as pH-Sensitive Indicators of Chitosan/Starch/Alginate Matrices
Intelligent packaging combines benefits from active (antimicrobial, antioxidant, etc.) and intelligent packaging (sensing and sharing information about the condition of packaged products) [207]. Food spoilage is associated with pH change, which enables the use of alternative, inexpensive, natural-based colorimetric pH indicators in the form of labels or tags. These pH-sensitive indicators could react with the non-neutral volatile gases that were generated from foods during spoilage and are composed of natural and safe pH sensing pigments, such as anthocyanins and curcumin and a dye carrier/(solid matrix) [208]. Both ingredients have to be non-toxic, meet the food safety requirements, and be stable at the applied pH [209].
Anthocyanins are natural-based, non-toxic, water soluble pigments, extracted from different plants that provide the purple, blue, and red color of many plants [208]. Anthocyanins possess excellent antioxidant potential [210][211][212], which can be released from packaging films [213] for extending shelf life of food, anti-inflammatory [214], and anticarcinogenic [215] activities. Moreover, the colors of anthocyanins are sensitive to pH changes due to their structural transformations [216,217]. Thus, films incorporated with anthocyanins can be used as antioxidant, intelligent food packaging that can monitor the food quality (as colorimetric indicators) [218] because food spoilage is frequently associated with pH change (Figure 7) [219].
For example, by changing pH from 7 to 3, different color variations (from brown to bright red) were observed in chitosan films containing black soybean seed coat extract (BSSCE) rich in various anthocyanins while the plain chitosan film was colorless and did not respond to pH changes [205]. Similarly, the color of purple-fleshed sweet potato extract (PSPE) encapsulated into the chitosan matrix could change the color with pH from pink-red (pH 3-6) to purple-brown (pH 7-8) to finally greenish-green (pH 9-10) (depending on the incorporated amount of PSPE) [220]. Likewise, aqueous hibiscus extract (HAE) encapsulated in chitosan changed color under different pH conditions: brown to lightly greenish tones were observed at pH values ranging from 5 to 8 while yellow color was observed at pH 13.0 [204]. requirements, and be stable at the applied pH [209].
Anthocyanins are natural-based, non-toxic, water soluble pigments, extracted from different plants that provide the purple, blue, and red color of many plants [208]. Anthocyanins possess excellent antioxidant potential [210][211][212], which can be released from packaging films [213] for extending shelf life of food, anti-inflammatory [214], and anticarcinogenic [215] activities. Moreover, the colors of anthocyanins are sensitive to pH changes due to their structural transformations [216,217]. Thus, films incorporated with anthocyanins can be used as antioxidant, intelligent food packaging that can monitor the food quality (as colorimetric indicators) [218] because food spoilage is frequently associated with pH change (Figure 7) [219].
For example, by changing pH from 7 to 3, different color variations (from brown to bright red) were observed in chitosan films containing black soybean seed coat extract (BSSCE) rich in various anthocyanins while the plain chitosan film was colorless and did not respond to pH changes [205]. Similarly, the color of purple-fleshed sweet potato extract (PSPE) encapsulated into the chitosan matrix could change the color with pH from pink-red (pH 3-6) to purple-brown (pH 7-8) to finally greenish-green (pH 9-10) (depending on the incorporated amount of PSPE) [220]. Likewise, aqueous hibiscus extract (HAE) encapsulated in chitosan changed color under different pH conditions: brown to lightly greenish tones were observed at pH values ranging from 5 to 8 while yellow color was observed at pH 13.0 [204].
Anthocyanins, which are phenolic compounds with hydroxyl groups used as an indicator dye [221] could reduce the solubility of chitosan in distilled water [205] as they proved to support chitosan hydrogel formation with reduced water absorption and solubility [222]. Migration tests that showed that anthocyanins from chokeberry extract are both chemically bonded and physically immobilized in the chitosan matrix due to the interactions between the phenolic components and the hydroxyl and free amine groups of chitosan [209]. This is an important feature for the edible coatings: Applying the coating in humid conditions but not liquid media, or on the surface of the product, would not lead to leakage of the dye [209] while the coatings kept their swelling ability, which still provided efficient pH sensing in the bulk material [209]. Color change of poly(vinyl alcohol)/chitosan/anthocyanin films in contact with raw pork belly slices exposed to ambient air for 12 h (left) and 24 h (right). After 12 h, the wrapping film becomes pink indicating an acidic condition near pH 5-6 on the surface of the pork slices. With further exposure for another 8 h, the pork meat turned dark-brown and softer, while the pH indicative film became yellowish with pale green, corresponding to a slightly alkaline range ( [221]).

Plant Extracts Incorporated As Antioxidants in Chitosan/Starch/Alginate Matrices
Oxidative reactions in food as a deteriorative process promote the discoloration and the development of rancidity and off-flavors [223], which is usually overcome by using synthetic antioxidants with suspicious health properties [224]. Currently, natural antioxidants are studied because they are considered to be safe and due to the high consumer acceptance and willingness to Figure 7. Color change of poly(vinyl alcohol)/chitosan/anthocyanin films in contact with raw pork belly slices exposed to ambient air for 12 h (left) and 24 h (right). After 12 h, the wrapping film becomes pink indicating an acidic condition near pH 5-6 on the surface of the pork slices. With further exposure for another 8 h, the pork meat turned dark-brown and softer, while the pH indicative film became yellowish with pale green, corresponding to a slightly alkaline range ( [221]).
Anthocyanins, which are phenolic compounds with hydroxyl groups used as an indicator dye [221] could reduce the solubility of chitosan in distilled water [205] as they proved to support chitosan hydrogel formation with reduced water absorption and solubility [222]. Migration tests that showed that anthocyanins from chokeberry extract are both chemically bonded and physically immobilized in the chitosan matrix due to the interactions between the phenolic components and the hydroxyl and free amine groups of chitosan [209]. This is an important feature for the edible coatings: Applying the coating in humid conditions but not liquid media, or on the surface of the product, would not lead to leakage of the dye [209] while the coatings kept their swelling ability, which still provided efficient pH sensing in the bulk material [209].

Plant Extracts Incorporated As Antioxidants in Chitosan/Starch/Alginate Matrices
Oxidative reactions in food as a deteriorative process promote the discoloration and the development of rancidity and off-flavors [223], which is usually overcome by using synthetic antioxidants with suspicious health properties [224]. Currently, natural antioxidants are studied because they are considered to be safe and due to the high consumer acceptance and willingness to buy these products [225]. Incorporation of natural antioxidants into packaging material (active packaging) [226] can be more effective than adding high levels of additives directly into the food [227].
Plant-derived phenolic compounds are natural antioxidants [228] that can scavenge reactive oxygen species by inhibiting the oxidation of low-density lipoproteins [229], which makes them substitutes for synthetic antioxidants in the food industry [230][231][232][233]. These polyphenols could be incorporated [234] within a film or coating applied to the food [235], which could release the antioxidant into the product or act on its surface, limiting the oxidative reactions of food components [236]. Aromatic herbs containing polyphenols have been traditionally used as healthy food ingredients [237][238][239][240] obtained through an aqueous extraction [241,242] process.
The direct addition of polyphenols to food is limited by their relatively rapid depletion [243]. The combined use of natural antioxidants and packaging materials increases the effectiveness of the antioxidants due to the protective effect of the chitosan matrix against polyphenol oxidation during storage of the films [244] and extending their action during a longer time [245,246].
For example, the use of a chitosan coating enriched with moringa leaf extract on avocado [193] and alginate coating enriched with grape seed extract on grapes [247] have demonstrated improvement in their overall quality. Similar enhancements in antioxidant activity were achieved when grape pomace extract [248], maqui berry extract [249], thinned young apple [250], peanut skin (EPS), and pink pepper residue (EPP) extract [251] polyphenols were incorporated into a chitosan film while the chitosan film itself showed very low antioxidant activity [252] due to the absence of antioxidants along with the presence of catalysts of the lipid oxidation (light, technological treatment, presence of salt and unsaturated lipids) [251]. Blueberry leaf extracts (BLE) incorporated into a chitosan coating could maintain higher radical scavenging activity (RSA) of fresh blueberries during refrigerated storage in the first days of storage, but after three days the samples had lower RSA than the control and chitosan coating alone [191].
As chitosan interacted with the polyphenols to a greater extent than starch, it is reported that the fastest delivery rate and the higher delivery ratio of thyme extract polyphenols [253] were when starch is used as the matrix, which is explained by the high solubility of starch matrix, without the crosslinking effect with the phenolic compounds [253].
The peroxide value (the quantity of the total primary oxidation products present in edible oils [254]) of rainbow trout coated by dipping with films containing chitosan and different concentrations of pomegranate peel extract (PPE), was significantly lower compared to the control [255] during storage time due to the proper antioxidant effect of the PPE, which inhibited superoxide hydroxyl and peroxyl, which finally lead to the oxidation of fats [256]. However, even though the best performance to prevent the oxidation of fats and proteins and also antimicrobial efficacy was observed for higher plant extract content, due to its undesirable color, the chitosan combined with 2% PPE was preferred [255].

Phenols from Plant Extracts as Crosslinkers for the Chitosan/Starch/Alginate Matrices
Swelling ability is beneficial for the release of active substances and also in the case of indicator labels [257] because the aqueous media with the changed pH can penetrate into the bulk matrix, which enhances the effectiveness of the pH sensing and also controls the release. In the same time, dissolution and degradation are undesired [258]. For chitosan films containing active substances it is important to reduce its solubility (e.g., via cross-linking) [259], thus preventing the indicator label/active substances from dissolving when pH is lowered due to food spoilage as the pH affects the swelling and release behavior of the active substances [260].
In order to replace toxic chemical cross-linkers for hydrogel formation, such as glutaraldehyde [261] or epichlorohydrin [262], edible chitosan films with reduced solubility can be obtained by using cross-linking agents extracted from natural plants [263].
Phenolic components obtained from different kinds of plants can interact (intermolecular interactions) with hydroxyl and free amine groups of [264,265] that reduce the solubility of chitosan films: by hydrogen-bonding, electrostatic attraction (ionic complexations in acidic conditions) [266] between the anthocyanins and chitosan, and even through ester linkage [253,267]. For example, a small amount of purple-fleshed sweet potato extract (PSPE) (5 wt % on chitosan basis) could establish physical interactions with chitosan molecules and act as bridges among different chitosan chains [205,220].
Thus, the incorporation of pure phenolics or phenolic-rich plant extracts [42,268], in addition to the increased antioxidant ability, can greatly enhance the physical property (by crosslinking through non covalent bonds) of chitosan film (thinned young apple polyphenols [250], thyme extract [244], and protocatechuic acid-a potent antioxidant agent found in fruits and vegetables [269]), leading to a more rigid and compact chitosan matrix and improving the film physical properties [244].
Tannic acid is a polyphenol naturally found in some green leaves, which exhibits antioxidant properties due to its multiple phenolic groups which can help crosslinking chitosan films [270], a process facilitated by exposure to high temperatures (100 • C) [271]. Thyme-extract polyphenols have been also used as crosslinkers [253,272].
The interactions of chitosan with phenolic substances through non-covalent bonds were proved by FTIR analysis, for example, for chitosan films containing black soybean seed coat extract (BSSCE) [205].
The IR spectra evidenced that the incorporation of the phenolic substances into the chitosan led to the presence of a new absorption band appearing at 1707 cm −1 [273] (1715 cm −1 [267]), or 1660 cm −1 [267], which became more pronounced by increasing the extract content [207] and was attributed to an ester linkage [267,274] (C=O stretching [273]).
For the chitosan purple-fleshed sweet potato extract (PSPE) films, the band around 3290 cm −1 broadened, while the band of N-H bending (1553 cm −1 ) gradually decreased with the increase of PSPE amount [220]. The absorptions at 3500-3000 cm −1 reflecting the stretching vibration of hydrogen bonds between the lattice hydroxyls and organic groups were stronger in pure chitosan film compared to those incorporated with pomegranate rind powder extract (PRP) [273] and was shifted to lower frequencies in chitosan/pomegranate rind powder extract (PRP) blended films [273]. The peaks at 1561 cm −1 (N-H band) and 1422 cm −1 (C-H band) (characteristic peaks of chitosan) flattened with incorporating PRP [273]. Other authors reported a gradual decrease of the 1553 cm −1 band (N-H bending) with the increase in PSPE amount [220].
Similarly, the color data regarding the films with different concentrations of phenolic compounds measured at different times proved that there are interactions between the chitosan and the phenolic compounds present in the extract [267].
The beneficial effects of the interactions (crosslinking) of phenolic substances with the chitosan/starch/alginate matrices are 1) delaying/controlling the release of the active substances: The incorporation of tannic acid as crosslinking agent into chitosan films delayed the thyme extract polyphenols release rate in water and ethanol aqueous solutions, and also reduced the average water content of chitosan-starch films without affecting their solubility [253]; 2) enhancing the mechanical behavior: When mixed with chitosan, the polyphenols from thyme extract interacted with the chitosan chains, acting as crosslinkers and enhancing the tensile behavior of the films. The opposite effect was observed when incorporated into the starch matrix [244]. The supplemental addition of tannic acid to the chitosan-based films also produced a further significant increase in the elastic modulus, tensile strength, and lower elongation at break due to the crosslinking effect [244].
Similar improvements were reported for chitosan films incorporating murta leaf extracts, rich in polyphenolic compounds [275]. Higher tensile strength as compared to plain chitosan film were found in chitosan green tea extract [276]. However other authors reported that the tensile strength of chitosan films containing anthocyanin-rich purple-fleshed sweet potato extract (PSPE) was not very different from those of pure chitosan films but decreased the elongation at break [220,252]. However, a significant reduction in the tensile strength was detected when PSPE amount increased to 10 wt % [220]. The incorporation of PSPE also caused significant decreases in the diffraction peak intensities of chitosan with the increase in PSPE amount due to newly formed intermolecular hydrogen bonds between the chitosan chains and anthocyanins in PSPE [220].
3) Decreased water barrier properties (decreased water vapor permeability (WVP)): Tannic acid (TA) was reported to decrease water vapor permeability (WVP) due to the same crosslinking effect for chitosan [271]. However, other authors evidenced the water plasticization effect on the polymeric matrix which seems to mitigate the crosslinking effect of TA, as pure chitosan and chitosan: TA films had greater values of water vapor WVP and oxygen permeabilities than the starch films while the chitosan:starch films exhibited intermediate behavior [244].
In addition to the mentioned crosslinking effect, other authors attribute the enhanced water vapor barrier property of chitosan films incorporating black soybean seed coat extract (BSSCE) to the bulky aromatic and pyrylium rings in the skeleton of anthocyanins that could obstruct the inner networks of chitosan-black soybean seed coat extract (BSSCE) films and reduce water vapor affinity of films [205].
The lower WVP of the films incorporated with different plant extracts may be also due to the hydrogen and covalent interactions between the chitosan network and polyphenolic compounds, which reduce the availability of the hydrophilic groups [277] and lead subsequently to a decrease in the affinity of chitosan film towards water molecules [252]. Similar decrease in WVP values were reported when chitosan film was incorporated with apple polyphenol. [250]. However, when the amount of the plant is too high (for example 15 wt % for purple-fleshed sweet potato extract (PSPE)), the dispersion of the extract destroyed the dense and compact structure of film, resulting in the increase of WVP [220]. 4) Increased stability under different pH in aqueous media: The stability under different pH in aqueous media is an important requirement for the applicability of the edible coated films. The water uptake of chitosan was remarkably reduced by the presence of chokeberry pomace extract (AEX): the modified chitosan films were stable and did not break apart during the swelling tests even under acidic pH due to the interactions between chitosan network and polyphenolic compounds which reduce the availability of the hydrophilic groups [209]. 5) Decreased moisture content: Due to this interaction, which greatly limited water-chitosan intermolecular interactions, the moisture contents in the chitosan films decreased with the addition of the polyphenols from plants extract. [220]. Similarly, chitosan-black soybean seed coat extract (BSSCE) films [205] or chitosan/aqueous hibiscus extract films [204] presented lower moisture contents in comparison to pure chitosan film. The opposite effect was observed for starch and gelatin films: The addition of the aqueous hibiscus extract promoted a significant increase in water content [204].

Conclusions
Plants provide materials which can be used as additives into polymeric materials, such as lignocellulosic fibers, nano-cellulose, or lignin, as well as plant extracts containing bioactive phenolic and flavonoid compounds used in the food packaging area. The lignocellulosic materials, lignin and nano-cellulose, can be used as reinforcements in various polymer matrices. As active ingredients in food packaging materials, based on chitosan/starch/alginate, the plant extracts can decrease the respiration rate and can delay the declining of the total phenolic content, flavonoids, anthocyanin content, and antioxidant activity in various fruits, as well as provide UV protection and can act as crosslinkers for the chitosan/starch/alginate matrices.