Direct Amplification of High Energy Pulsed Laser in Fiber-Single Crystal Fiber with High Average Power

A laser master oscillator power amplifier (MOPA) system consisting of a fiber amplifier and a two-stage Yb:YAG single crystal fiber (SCF) is experimentally studied. The nonlinear stimulated Raman scattering (SRS) is avoided by limiting the output power of the fiber preamplifier to 600 mW. Due to the benefit from the low nonlinearity and high amplification gain of the SCF, a laser pulse duration of 16.95 ps and a high average power of 41.7 W at a repetition rate of 250 kHz are obtained by using a two-stage polarization controlled double-pass amplification of Yb:YAG SCF, corresponding to an output energy of 166.8 μJ and a peak power of 9.84 MW, respectively. The polarization controlled SCF amplification scheme achieved a gain as high as more than 69 times. During the amplification, the spectra gain narrowing effect and the polarization controlled four-pass amplification setup are also studied. The laser spectrum is narrowed from over 10 nm to less than 3 nm, and the pulse width is also compressed to hundreds of femtosecond by dechirping the laser pulse. This compact-sized, cost-effective laser source can be used in laser micromachining, or as the seeder source for generating much higher power and energy laser for scientific research. For some applications which need femtosecond laser, this laser source can also be compressed to femtosecond regime.


Introduction
High-performance picosecond lasers with high-power, high-energy, and high-repetition-rate are in great demand in many industrial micromachining [1,2] and scientific applications [3], such as the processing of ceramics, diamonds, certain transparent materials, and optical parametric chirped pulse amplification (OPCPA) systems.Different kinds of laser amplifiers are used to obtain the high-power, high-energy picosecond laser.With the appearance of large mode area photonic crystal fiber [4,5], the influence of the nonlinear effect in the fiber laser amplifier is reduced.Fiber amplifiers have potential in high-power picosecond laser amplification, and by using the fiber master oscillator power amplifier (MOPA) system, some high-power picosecond MOPA systems are demonstrated.Ho-Yin Chan et al. achieved laser power of 97 W and energy of 17.7 µJ with pulse duration of 124 ps by using a four-stage fiber MOPA [6].S. Pierrot reported 83 W, 14 µJ, 5.9 MHz, 30 ps MOPA fiber laser by using a rod-type large mode area photonic crystal fiber [7].Tong Liu et al. used a multi-stage fiber MOPA to obtain an average power of 117 W, pulse width of 200 ps at a repetition rate of 25 MHz [8].The fiber MOPA system can obtain high-power output, however, due to the high nonlinearity during the amplification the peak power is limited, typically no more than 1 MW.The thin disk Yb:YAG laser and Yb-Innoslab laser Crystals 2019, 9, 216 2 of 9 achieved some impressive results, such as 1.6 ps pulses with 30 mJ at 300 W of output power by using a thin disk laser [9], and 54 mJ, 1.5 ps at 0.5 kW of output power by using a Innoslab laser [10].However, its inherent complexity and thermal management pose a challenge for many applications.Therefore, some relatively simple systems are studied, such as using the double-passing end-pumped Nd:YVO4 rod amplifier [11], which delivers 90 ps and 10.2 W laser at the repetition of 70 kHz with a peak power of 1.6 MW.By using the fiber and bulk hybrid MOPA system, a 70 W average power laser at 1064 nm with 1000 kHz repetition rate and 83 ps pulse duration is demonstrated [12].
The SCF is a new architecture, between the bulk crystals and the optical fibers, allowing higher average powers than with conventional crystals, and higher energy than with optical fibers in a pulsed regime.During the SCF amplification, the pump laser from the fiber-coupled laser diode is confined by the guiding capacity of the Yb:YAG SCF, whereas the seeder laser beam is in free propagation.Due to the benefit from the better overlap between the pump beam and signal beam, a higher amplification gain can be obtained.Therefore, this technology has prospects in picosecond or femtosecond laser systems with compact size and simplicity, and by employing this kind of amplifier the systems are more robust and less expensive.To generate femtosecond laser, the single crystal fiber is employed in chirped pulse amplification systems [13], and it is also demonstrated in a direct picosecond laser amplification, which has typical output parameters of 200 k Hz, 180 µJ.The seeder is a high-energy commercial laser source with energy of 40 µJ and pulse width of 27 ps [14].
As in our previous work, we focus on the high-energy femtosecond laser.By using the SCF in the chirped amplification system, we obtained average power of 15.57W, pulse duration of 715 fs and pulse energy of 155.7 µJ.During the amplification, the pulse is stretched to more than 600 picosecond and uses the transmission grating pair to compress the pulse [15].Due to the short pulse duration, we can achieve so called "cold processing" in the applications of high-precision laser micromachining, such as materials cutting, etching, and hole drilling.However, we have to balance the heat effect and the processing efficiency.Specifically, the shorter pulse width results in less thermal effect in the processing, however, the laser source will be more expensive with the dispersion components.With the same cost, we can obtain a higher high-power picosecond laser with high processing efficiency.In many applications, the thermal effect in the processing is acceptable with a laser pulse width of tens of picosecond.In this work, we report a high-energy and high-power picosecond laser with fiber-single crystal fiber hybrid MOPA system by employing two-stage SCF amplifiers, which delivers a maximum output 41.7 W at 250 kHz, with a pulse width of 16.95 ps, corresponding to a peak power of 9.84 MW, and the spectrum width is narrowed to ~3 nm.The correlation between the spectra revolution and the pulse width is also explored.The polarization controlled high-gain four-pass amplification setup is also experimentally studied, which can obtain higher gain as compared with the single-and double-pass amplification setup.

Experimental Setup
The experimental setup, schematically shown in Figure 1, consisted of an oscillator, a 100 m polarization maintaining (PM) fiber stretcher, a one-stage polarization maintaining (PM) single-mode fiber and two-stage PM cladding fiber amplifier, a pulse picker, and a two-stage Yb:YAG SCF amplifier.
The seed source was a mode-locked PM fiber laser operating at 40.7 MHz repetition rate, delivering 10 ps pulses centered at 1030 nm with spectral bandwidth of 10 nm and average power of 20 mW.This was a positive chirped pulse output and could be compressed to less than 300 fs.The 100 m PM fiber stretcher was utilized to stretch the pulse duration to about 40 ps, to lower the nonlinearity accumulated in the fiber amplifier stage.The first stage amplifier was a single mode amplifier, and an output power of 80 mW was obtained when the pump power was 250 mW.The second amplifier was a double cladding PM Yb-doped fiber (YDF) amplifier with a core diameter of 10 µm and a cladding diameter of 125 µm with fiber length of 1.2 m.At a pump power of 4.5 W, the output power of 1.5 W was obtained.Then, a fiber-based acousto-optic modulator was used to decrease the repetition rate of the oscillator before amplification in the third stage double cladding YDF amplifier with a core diameter of 25 µm and cladding diameter of 250 µm with fiber length of 1.5 m.The repetition rate was decreased to 250 kHz in the second stage fiber amplifier.After the AOM, the average power was approximately 2 mW.Limited by the severe nonlinearity, especially the onset of the nonlinear stimulated Raman scattering, the amplified power was limited to about 600 mW.
The pump was imaged inside the SCF with a magnification factor of 3.75 using two plano convex lenses.The focused pumped laser beam diameter was about 400 μm.A pair of dichroic mirrors with parameters of reflectivity of 99.5% @1030 nm and transmissivity of 97% @1020-1080 nm was used to separate the incoming pump beam and the signal beam.After the first pass amplification, the laser beam was focused by a lens (L2), and its laser waist was located on a highly reflective mirror coating at 0 degree consisting a f-f configuration.A quarter wave plate was inserted before the reflective mirror.After the laser beam passed the quarter wave plate twice, its polarization direction was rotated by 90° and could be extracted by the polarization beam splitter(PBS).After the first stage SCF amplifier, the power was about 12 W. Then the amplified laser was injected into the second stage SCF amplifier with a plano-convex lens with a focal length of 250 mm and the double-pass structure was nearly the same as the first stage amplifier.WDM: wavelength-division multiplexer; LD: laser diode; YDF: Yb-doped fiber; HWP: half wave plate; QWP: quarter wave plate; ISO: isolator

Experimental Results and Discussions
In the fiber preamplifier, the nonlinearity, especially the stimulated Raman scattering, is avoided.In the second stage double cladding fiber amplifier, the pulse repetition rate is only 250 kHz.The main amplifier was a two-stage polarization controlled double-pass amplifier based on the Yb:YAG SCF gain module using the parameters of 30 mm length, diameter of 1 mm, and doping rate of 1 at.%.The facets were antireflection coated for both the signal and the pump wavelength to prevent parasitic lasing and excess losses at the interfaces.The SCF module was water cooled at a temperature of 20 • C by a water cooler with a cooling capacity of 1300 W.During the amplification, the seed beam from the preamplifier with core diameter of 25 µm was collimated to ~0.4 mm and the diameter was further propagated through Yb:YAG SCF.The SCF was end pumped by a fiber coupled laser diode with an output power of 140 W at 940 nm, a core diameter of 106 µm, and an NA of 0.22.The pump was imaged inside the SCF with a magnification factor of 3.75 using two plano convex lenses.The focused pumped laser beam diameter was about 400 µm.A pair of dichroic mirrors with parameters of reflectivity of 99.5% @1030 nm and transmissivity of 97% @1020-1080 nm was used to separate the incoming pump beam and the signal beam.After the first pass amplification, the laser beam was focused by a lens (L2), and its laser waist was located on a highly reflective mirror coating at 0 degree consisting a f-f configuration.A quarter wave plate was inserted before the reflective mirror.After the laser beam passed the quarter wave plate twice, its polarization direction was rotated by 90 • and could be extracted by the polarization beam splitter (PBS).After the first stage SCF amplifier, the power was about 12 W. Then the amplified laser was injected into the second stage SCF amplifier with a plano-convex lens with a focal length of 250 mm and the double-pass structure was nearly the same as the first stage amplifier.

Experimental Results and Discussions
In the fiber preamplifier, the nonlinearity, especially the stimulated Raman scattering, is avoided.In the second stage double cladding fiber amplifier, the pulse repetition rate is only 250 kHz.In order to generate high peak power laser confined in the 25 µm fiber core, the nonlinear self-phase modulation and the stimulated Raman scattering is found.By controlling the amplification gain, different output power and the corresponding spectrum is detected, as shown in Figure 2. The spectra of amplified power of 220 mW, 525 mW, 600 mW, and 700 mW are measured using the optical spectrum analyzer (AQ 6370C, YOKOGAWA, Tokyo, Japan), respectively, from the spectra.In order to avoid the onset of the SRS, the amplified power is limited to less than 600 mW.During the fiber amplification, the spectrum is carefully detected, because the ASE peak is the same wavelength centered in 1030 nm in the fiber amplifier, and therefore it is hard to assess the amount of ASE in the preamplifier.However, the ASE have different laser divergence as compared with the laser beam, so we detected the ASE using an infrared card since after the laser output from the fiber, the ASE component could not be detected.
Crystals 2019, 9, x FOR PEER 4 of 9 In order to generate high peak power laser confined in the 25 μm fiber core, the nonlinear self-phase modulation and the stimulated Raman scattering is found.By controlling the amplification gain, different output power and the corresponding spectrum is detected, as shown in Figure 2. The spectra of amplified power of 220 mW, 525 mW, 600 mW, and 700 mW are measured using the optical spectrum analyzer (AQ 6370C, YOKOGAWA, Tokyo，Japan), respectively, from the spectra.In order to avoid the onset of the SRS, the amplified power is limited to less than 600 mW.During the fiber amplification, the spectrum is carefully detected, because the ASE peak is the same wavelength centered in 1030 nm in the fiber amplifier, and therefore it is hard to assess the amount of ASE in the preamplifier.However, the ASE have different laser divergence as compared with the laser beam, so we detected the ASE using an infrared card since after the laser output from the fiber, the ASE component could not be detected.The first stage SCF amplifier's performance is measured with an input power of 600 mW.The output powers of single-and double-pass amplifications are measured, respectively, as shown in Figure 3. Correspondingly, the output power of 4.9 W and 11.37 W is obtained with a maximum pump power of 109.2W. We find that the amplification gain from the single crystal fiber is impressively improved when the laser is operated in double pass.During the double-pass amplification, the maximum amplification gain of 18.95 is obtained.After the first stage amplification of SCF amplifier，the laser power is scaled to more than 10 W at a repetition rate of 250 kHz.Then the laser is focused into the second stage amplifier as the signal The first stage SCF amplifier's performance is measured with an input power of 600 mW.The output powers of single-and double-pass amplifications are measured, respectively, as shown in Figure 3. Correspondingly, the output power of 4.9 W and 11.37 W is obtained with a maximum pump power of 109.2W. We find that the amplification gain from the single crystal fiber is impressively improved when the laser is operated in double pass.During the double-pass amplification, the maximum amplification gain of 18.95 is obtained.
Crystals 2019, 9, x FOR PEER 4 of 9 In order to generate high peak power laser confined in the 25 μm fiber core, the nonlinear self-phase modulation and the stimulated Raman scattering is found.By controlling the amplification gain, different output power and the corresponding spectrum is detected, as shown in Figure 2. The spectra of amplified power of 220 mW, 525 mW, 600 mW, and 700 mW are measured using the optical spectrum analyzer (AQ 6370C, YOKOGAWA, Tokyo，Japan), respectively, from the spectra.In order to avoid the onset of the SRS, the amplified power is limited to less than 600 mW.During the fiber amplification, the spectrum is carefully detected, because the ASE peak is the same wavelength centered in 1030 nm in the fiber amplifier, and therefore it is hard to assess the amount of ASE in the preamplifier.However, the ASE have different laser divergence as compared with the laser beam, so we detected the ASE using an infrared card since after the laser output from the fiber, the ASE component could not be detected.The first stage SCF amplifier's performance is measured with an input power of 600 mW.The output powers of single-and double-pass amplifications are measured, respectively, as shown in Figure 3. Correspondingly, the output power of 4.9 W and 11.37 W is obtained with a maximum pump power of 109.2W. We find that the amplification gain from the single crystal fiber is impressively improved when the laser is operated in double pass.During the double-pass amplification, the maximum amplification gain of 18.95 is obtained.After the first stage amplification of SCF amplifier，the laser power is scaled to more than 10 W at a repetition rate of 250 kHz.Then the laser is focused into the second stage amplifier as the signal After the first stage amplification of SCF amplifier, the laser power is scaled to more than 10 W at a repetition rate of 250 kHz.Then the laser is focused into the second stage amplifier as the signal power with a focused laser diameter of 400 µm.The amplification outputs of single pass and double pass in the second stage SCF amplifier are measured with different pump powers, as shown in Figure 4.At the maximum pump power, we obtained 34 W and 41.7 W in single-and double-pass amplification, respectively.During the double-pass amplification, the thermal lens effect of the SCF has more influence on the gain of the amplification than that of the single-pass amplification.During the double-pass amplification, the saturation process has been observed.To explain this phenomenon, it is speculated that the reabsorption of the amplified laser power will exacerbate the thermal lens effect, which will result in a mode field overlap ratio mismatch between the pump power and the signal power, which influences the amplification gain, and therefore a little saturation is observed.The output beam quality is also measured using Spiricon M2-200s (Ophir, Jerusalem, Israel), as shown in Figure 5.
The measured M2 results are 1.328 in the horizontal direction and 1.498 in the vertical direction, respectively.The amplified laser beam density distribution is also detected using a BC106N camera from Thorlabs (Newton, New Jersey, United States), which closes to a Gaussian density distribution shown in the inset of Figure 5.
Crystals 2019, 9, x FOR PEER 5 of 9 power with a focused laser diameter of 400 μm.The amplification outputs of single pass and double pass in the second stage SCF amplifier are measured with different pump powers, as shown in Figure 4.At the maximum pump power, we obtained 34 W and 41.7 W in single-and double-pass amplification, respectively.During the double-pass amplification, the thermal lens effect of the SCF has more influence on the gain of the amplification than that of the single-pass amplification.During the double-pass amplification, the saturation process has been observed.To explain this phenomenon, it is speculated that the reabsorption of the amplified laser power will exacerbate the thermal lens effect, which will result in a mode field overlap ratio mismatch between the pump power and the signal power, which influences the amplification gain, and therefore a little saturation is observed.The output beam quality is also measured using Spiricon M2-200s (Ophir, Jerusalem, Israel), as shown in Figure 5.The measured M2 results are 1.328 in the horizontal direction and 1.498 in the vertical direction, respectively.The amplified laser beam density distribution is also detected using a BC106N camera from Thorlabs (Newton, New Jersey, United States), which closes to a Gaussian density distribution shown in the inset of Figure 5.During the amplification, the spectral gain narrowing effect is measured at different amplification outputs, as shown in Figure 6.The spectra of the fiber preamplifier with a power of 600 mW, the first stage SCF amplifier with a power of 10 W, and the second stage SCF amplifier with a power of 41.7 W are measured.From the spectra, we find the obvious gain narrowing effect.The gain narrowing issue is caused by the narrow and uneven emission spectrum of the Yb:YAG crystal.Explicitly, the emission spectrum width is less than 8 nm at the cooling temperature of 20 • C, moreover, the central wavelength component has a higher gain than the off-center wavelengths.As a result, the spectrum width is narrowed when the original seed laser source is amplified.Because the oscillator is a mode-locked fiber laser with positive chirp and spectrum width of 10 nm, the seeder pulse is then stretched to about 40 ps by the 100 m fiber stretcher.During the amplification, the spectrum is modulated by nonlinear SPM effect and the spectral width is also narrowed by the spectral gain narrowing effect.The spectrum is narrowed to less than 3 nm when the laser is amplified to 41.7 W. Because the seeder is a chirped pulse output, when the spectrum is narrowed, the pulse width is also narrowed.The autocorrelation curves of the preamplifier, the first-stage SCF amplifier, and the second stage SCF amplifier are measured, as shown in the Figure 7. Correspondingly, the pulse width, with Gaussian fit, is 40.13 ps, 24.86 ps, and 16.95 ps, respectively.The amplified output pulse spectrum of 3 nm spectrum width can also sustain the Fourier transform limited pulse duration of 520 fs (Assuming the pulse shape is Gaussian shape with a time bandwidth product of 0.441).The SPM is a nonlinear effect which appears during the high energy pulse amplification, especially in the fiber amplifier, where the mode field area is relatively small and interaction length is long.The nonlinear effect will accumulate in the fiber amplifier, which will introduce some nonlinear phase shift during the recompression and lead to the recompressed pulse having some pedestals.As a result of this phenomenon the pulse width cannot be compressed to the Fourier transform limited pulse duration.However, it is possible that the amplified chirped pulse with ~3nm spectrum width can also be compressed to femtosecond regime (<1 ps) and even has some pedestals.In some applications, which needs femtosecond laser, this high energy laser source can also be compressed to femtosecond regime by dechirping the laser pulse.During the amplification, the spectral gain narrowing effect is measured at different amplification outputs, as shown in Figure 6.The spectra of the fiber preamplifier with a power of 600 mW, the first stage SCF amplifier with a power of 10 W, and the second stage SCF amplifier with a power of 41.7 W are measured.From the spectra, we find the obvious gain narrowing effect.The gain narrowing issue is caused by the narrow and uneven emission spectrum of the Yb:YAG crystal.Explicitly, the emission spectrum width is less than 8 nm at the cooling temperature of 20 °C, moreover, the central wavelength component has a higher gain than the off-center wavelengths.As a result, the spectrum width is narrowed when the original seed laser source is amplified.Because the oscillator is a mode-locked fiber laser with positive chirp and spectrum width of 10 nm, the seeder pulse is then stretched to about 40 ps by the 100 m fiber stretcher.During the amplification, the spectrum is modulated by nonlinear SPM effect and the spectral width is also narrowed by the spectral gain narrowing effect.The spectrum is narrowed to less than 3 nm when the laser is amplified to 41.7 W. Because the seeder is a chirped pulse output, when the spectrum is narrowed, the pulse width is also narrowed.The autocorrelation curves of the preamplifier, the first-stage SCF amplifier, and the second stage SCF amplifier are measured, as shown in the Figure 7. Correspondingly, the pulse width, with Gaussian fit, is 40.13 ps, 24.86 ps, and 16.95 ps, respectively.The amplified output pulse spectrum of 3 nm spectrum width can also sustain the Fourier transform limited pulse duration of 520 fs.(Assuming the pulse shape is Gaussian shape with a time bandwidth product of 0.441.)The SPM is a nonlinear effect which appears during the high energy pulse amplification, especially in the fiber amplifier, where the mode field area is relatively small and interaction length is long.The nonlinear effect will accumulate in the fiber amplifier, which will introduce some nonlinear phase shift during the recompression and lead to the recompressed pulse having some pedestals.As a result of this phenomenon the pulse width cannot be compressed to the Fourier transform limited pulse duration.However, it is possible that the amplified chirped pulse with ~3nm spectrum width can also be compressed to femtosecond regime (<1ps) and even has some pedestals.In some applications, which needs femtosecond laser, this high energy laser source can also be compressed to femtosecond regime by dechirping the laser pulse.At the end of this experiment, we also explore the polarization controlled four-pass amplification setup.The setup is shown in Figure 8.Compared to the double-pass configuration, the half-wave plate, polarization beam splitter, and 45 • rotator are inserted into the amplifier to create the polarization controlled four-pass amplification.The amplification performance of single pass, double pass, and four pass is measured, which is shown in Figure 9.The higher gain is obtained during four-pass amplification when the signal power of 600 mW is amplified to more than 20 W. The four-pass amplification scheme has much higher power output during the small signal amplification, a route to get higher gain with a one gain medium.However, it also adds some disadvantages to the system, for example, it is more complicated as there are more lenses for the four-pass amplification, the possibility of an adjustment mistake, the high peak power density will damage the optical components, and furthermore, it is hard to control the amplified beam quality and the four-pass amplification may need more time for system optimization and system integration.Therefore, in the two-stage integration, in order to make the system easy to integrate and ensure the amplified laser has a good beam profile, we do not use the four-pass amplification scheme.For some amplifications, if there is less need for beam quality, the four-pass high gain system can be used in the multistage amplification to obtain much higher output.
of this phenomenon the pulse width cannot be compressed to the Fourier transform limited pulse duration.However, it is possible that the amplified chirped pulse with ~3nm spectrum width can also be compressed to femtosecond regime (<1ps) and even has some pedestals.In some applications, which needs femtosecond laser, this high energy laser source can also be compressed to femtosecond regime by dechirping the laser pulse.At the end of this experiment, we also explore the polarization controlled four-pass amplification setup.The setup is shown in Figure 8.Compared to the double-pass configuration, the half-wave plate, polarization beam splitter, and 45° rotator are inserted into the amplifier to create the polarization controlled four-pass amplification.The amplification performance of single pass, double pass, and four pass is measured, which is shown in Figure 9.The higher gain is obtained during fourpass amplification when the signal power of 600 mW is amplified to more than 20 W. The four-pass amplification scheme has much higher power output during the small signal amplification, a route to get higher gain with a one gain medium.However, it also adds some disadvantages to the system, for example, it is more complicated as there are more lenses for the four-pass amplification, the possibility of an adjustment mistake, the high peak power density will damage the optical components, and furthermore, it is hard to control the amplified beam quality and the four-pass amplification may need more time for system optimization and system integration.Therefore, in the two-stage integration, in order to make the system easy to integrate and ensure the amplified laser has a good beam profile, we do not use the four-pass amplification scheme.For some amplifications, if there is less need for beam quality, the four-pass high gain system can be used in the multistage amplification to obtain much higher output.

Conclusions
A high energy ultrashort laser master oscillator pulse amplification (MOPA) system based on a hybrid fiber-single crystal fiber is experimentally studied.During the amplification, the onset of SRS is effectively avoided.By using polarization controlled double-pass amplification of a two-stage Yb:YAG single crystal fiber amplifier, laser pulses with pulse duration of 16.95 ps and high average At the end of this experiment, we also explore the polarization controlled four-pass amplification setup.The setup is shown in Figure 8.Compared to the double-pass configuration, the half-wave plate, polarization beam splitter, and 45° rotator are inserted into the amplifier to create the polarization controlled four-pass amplification.The amplification performance of single pass, double pass, and four pass is measured, which is shown in Figure 9.The higher gain is obtained during fourpass amplification when the signal power of 600 mW is amplified to more than 20 W. The four-pass amplification scheme has much higher power output during the small signal amplification, a route to get higher gain with a one gain medium.However, it also adds some disadvantages to the system, for example, it is more complicated as there are more lenses for the four-pass amplification, the possibility of an adjustment mistake, the high peak power density will damage the optical components, and furthermore, it is hard to control the amplified beam quality and the four-pass amplification may need more time for system optimization and system integration.Therefore, in the two-stage integration, in order to make the system easy to integrate and ensure the amplified laser has a good beam profile, we do not use the four-pass amplification scheme.For some amplifications, if there is less need for beam quality, the four-pass high gain system can be used in the multistage amplification to obtain much higher output.

Conclusions
A high energy ultrashort laser master oscillator pulse amplification (MOPA) system based on a hybrid fiber-single crystal fiber is experimentally studied.During the amplification, the onset of SRS is effectively avoided.By using polarization controlled double-pass amplification of a two-stage Yb:YAG single crystal fiber amplifier, laser pulses with pulse duration of 16.95 ps and high average

Figure 1 .
Figure 1.Schematic diagram of the high energy picosecond master oscillator power amplifier (MOPA) system.

Figure 2 .
Figure 2. The nonlinear effect of stimulated Raman scattering (SRS) in the fiber preamplifier.

Figure 3 .
Figure 3. Output power of single-and double-pass amplification of the first stage SCF amplifier.

Figure 2 .
Figure 2. The nonlinear effect of stimulated Raman scattering (SRS) in the fiber preamplifier.

Figure 2 .
Figure 2. The nonlinear effect of stimulated Raman scattering (SRS) in the fiber preamplifier.

Figure 3 .
Figure 3. Output power of single-and double-pass amplification of the first stage SCF amplifier.

Figure 3 .
Figure 3. Output power of single-and double-pass amplification of the first stage SCF amplifier.

Figure 4 .
Figure 4. Output power of single-and double-pass amplification of the second stage SCF amplifier.

Figure 5 .
Figure 5.The M2 measurement at the maximum output power.

Figure 4 .
Figure 4. Output power of single-and double-pass amplification of the second stage SCF amplifier.

Figure 4 .
Figure 4. Output power of single-and double-pass amplification of the second stage SCF amplifier.

Figure 5 .
Figure 5.The M2 measurement at the maximum output power.

Figure 5 .
Figure 5.The M2 measurement at the maximum output power.

Figure 6 .
Figure 6.Spectrum measurement of different amplified power outputs.

Figure 6 .
Figure 6.Spectrum measurement of different amplified power outputs.

Figure 9 .
Figure 9. Amplification performance of single-, double-, and four-pass amplification versus the pump power.

Figure 9 .
Figure 9. Amplification performance of single-, double-, and four-pass amplification versus the pump power.

Figure 9 .
Figure 9. Amplification performance of single-, double-, and four-pass amplification versus the pump power.