Inﬂuence of Glazed Hollow Bead on the Performance of Polyvinyl Alcohol Fiber Reinforced Cement Composites

: To improve the thermal insulation properties and toughness of concrete, the glazed hollow bead (GHB) and polyvinyl alcohol (PVA) ﬁber reinforced cementitious composites (GPCC) were investigated by orthogonal test, which includes six GHB mass percentage (20%, 40%, 60%, 80%,100%, 120%), three PVA volume fraction (1%, 1.5%, 2%) and water binder ratio (0.26, 0.30, 0.34). Compressive, split tensile strengths and thermal conductivity of GHB-PVA reinforced cementitious composites (GPCC) were tested, and the mechanism of ﬁbers was analyzed from a microscopic perspective. The results revealed that the thermal insulation will be signiﬁcantly improved with the increased content of GHB, but the compressive and split tensile strength will be decreased simultaneously. No obvious effect was found by the PVA ﬁber addition on its strength indexes, and the presence of GHB will affect the bridging action of PVA ﬁbers. The water binder ratio has more effect on strengths than thermal conductivity. Based on the mechanical performance rather than the thermal insulation analysis test, the optimal mix proportions were proposed: mass percentage of 40% GHB, a volume fraction of 1.5% PVA ﬁber, and 0.26 water-binder ratio. Moreover, the anchoring and bridging effect of PVA ﬁbers will effectively balance the stress generated by the shrinkage of cement paste, and inhibits or even prevents the development of cracks. However, a certain number of tiny cracks will be formed near the GHB, and between GHB and PVA ﬁbers, which will cause local stretching and peeling of PVA, and shattering inside the GHB with the increase of external force. The ﬁndings of this study can provide a useful reference for the application of an insulated-bearing material with GHB and PVA ﬁber.


Introduction
The subject of energy conservation in buildings has become one of most important at present. With urbanization and increasing population, the energy consumption of buildings has reached 40% of the overall energy consumption worldwide [1,2]. Additionally, the global building sector has contributed 28% of global energy-related to CO 2 emissions [3]. Recently, measures of energy conservation in building were proposed for mitigating global warming caused by increased energy consumption and carbon use, in order to reduce the greenhouse gas emissions by 2030, which is in accordance with the Paris Agreement [4]. A large part of the energy consumption is related to heating and cooling of buildings [5,6]. Using the thermal performance of building materials to passively reduce thermal convection between the interior and exterior is considered to be the most effective way to save energy.
In terms of thermal insulation composites, cementitious materials containing GHB were explored extensively. GHB has a special structure with a closed surface and a hollow interior, and it has excellent characteristics of low density, low thermal conductivity, high temperature resistance, low water absorption, etc., which is a good choice to improve development of cracks in the foam concrete matrix and pore wall cracks, and reduce the water absorption and thermal conductivity of foam concrete [30].
To meet the requirements of energy saving and green development, a novel material with great heat insulation, load-bearing performance, and crack resistance for buildings, especially for special structures (such as storage structures), is needed. The former research and references have verified that the addition of PVA fiber can improve the concrete toughness excellently. Therefore, orthogonal tests were designed with the factors of GHB content, PVA fiber content, and water-binder ratio to investigate the mechanical and thermal performance of GPCC. Additionally, the micro-structure of the specimens was observed by SEM to explore the action of GHB and PVA fiber. This study provides a basis for further research on the application of GPCC and proposes an optimized mix proportion.

Materials
The test was conducted using P-O 42.5 grade ordinary silicate cement produced by Xinxiang Nova, Xinxiang, China, which has a 28 days compressive strength of 48.3 MPa. The I grade fly ash produced by a power plant was used. Natural river sand with a maximum particle diameter of 1.18 mm is used for fine aggregates. The fibers are made of polyvinyl alcohol fibers (PVA) from Kuraray, Tokyo, Japanese, their appearance and SEM image are shown in Figure 1 and the parameters are shown in Table 1. The GHB was produced by Hebei Yixin Building Material Technology Co., Ltd., Hengshui, China, its appearance and SEM image are shown in Figure 1, and the performance indexes are shown in Table 2. The AEWR air-entraining water reducer with a water reduction rate of 15% was used as the water reducer.
cracking of glass bead insulation mortar and improve the flexural strength of glass bead composite insulation material [27]. Xu J W et al. [28] showed that the effect of steel fibers on the compressive strength of insulating concrete was small, but could increase its tensile strength by 88.44%. Wang C G [29] mixed PVA with expanded vitrified small balls in foam concrete, which not only improved its mechanical properties significantly, but was also able to limit the development of cracks in the foam concrete matrix and pore wall cracks, and reduce the water absorption and thermal conductivity of foam concrete [30].
To meet the requirements of energy saving and green development, a novel material with great heat insulation, load-bearing performance, and crack resistance for buildings, especially for special structures (such as storage structures), is needed. The former research and references have verified that the addition of PVA fiber can improve the concrete toughness excellently. Therefore, orthogonal tests were designed with the factors of GHB content, PVA fiber content, and water-binder ratio to investigate the mechanical and thermal performance of GPCC. Additionally, the micro-structure of the specimens was observed by SEM to explore the action of GHB and PVA fiber. This study provides a basis for further research on the application of GPCC and proposes an optimized mix proportion.

Materials
The test was conducted using P-O 42.5 grade ordinary silicate cement produced by Xinxiang Nova, Xinxiang, China, which has a 28 days compressive strength of 48.3 MPa. The I grade fly ash produced by a power plant was used. Natural river sand with a maximum particle diameter of 1.18 mm is used for fine aggregates. The fibers are made of polyvinyl alcohol fibers (PVA) from Kuraray, Tokyo, Japanese, their appearance and SEM image are shown in Figure 1 and the parameters are shown in Table 1. The GHB was produced by Hebei Yixin Building Material Technology Co., Ltd., Hengshui, China, its appearance and SEM image are shown in Figure 1, and the performance indexes are shown in Table 2. The AEWR air-entraining water reducer with a water reduction rate of 15% was used as the water reducer.

Orthogonal Experimental Design
It has been shown that the water-binder ratio is the main factor affecting the mechanical properties of concrete, the PVA fiber content mainly improves the toughness of concrete, and the porosity and particle characteristics of lightweight fine aggregates are the main factors affecting the thermal conductivity of concrete. Therefore, with the background of a reserve grain depot project demand in Lanzhou City, according to the GPCC pre-testing results, this test was performed according to the orthogonal design table L 18 (6 1 × 3 2 ) of three factors and mix levels. GHBs are used in place of fine aggregates; the PVA fiber content, GHB content, and water-binder ratio were selected as the influencing factors of the orthogonal test. Eventually the volume percentage of GHB was designed as factor A with six levels (20%, 40%, 60%, 80%, 100%, 120%), the PVA fiber fraction was designed as factor B with three levels (1.0%,1.5%, 2.0%), and three water-binder ratio levels of 0.26, 0.3, and 0.34 were designed as factor C in this experiment. The factors and the levels of the orthogonal experiment are shown in Table 3. The mix proportions and test results are shown in Table 4.

Specimens Preparation
This test adopts forcing mixer to mix GPCC. Firstly, the feeding order is to put in cement, fly ash, sand, and GHB and mix well. Then the water reducing agent and water are evenly mixed and put into the mixture and stirred well. Finally, PVA fiber is added and mixing is continued, in order to create a mixture with good fluidity, fiber stirring without obvious agglomeration phenomenon, regarded as uniform mixing. The test blocks were cast in plastic test molds, vibrated, and compacted by shaking table, covered with cling film for 36 h and demolded, and maintained under standard maintenance conditions (relative humidity ≥ 95%, temperature 20 ± 1 • C) for 28 days, taken out and dried for the test of mechanical properties and thermal conductivity.

Test Methods
The compressive, split strengths, and thermal conductivity of GPCC were tested, and the microstructure images were observed. They are briefly described below.

Strength Test
The compressive strength and split tensile test were conducted in accordance with the "Standard for Test Method of Mechanical Properties on Ordinary Concrete" (GB/T 50081-2019, Chinese standard) [31] using a JYE-2000A type fully-automatic constant-pressure pressure testing machine (see Figure 2a,b) which produced by Beijing Ouya Zhongxing Science Co., Ltd., Beijing, China. The 100 × 100 × 100 mm 3 specimens were prepared to measure the compressive and split tensile strengths. As per the standards, the rate of loading should be controlled for 3 mm/min in the compressive strength and split tensile strength tests. cement, fly ash, sand, and GHB and mix well. Then the water reducing agent and water are evenly mixed and put into the mixture and stirred well. Finally, PVA fiber is added and mixing is continued, in order to create a mixture with good fluidity, fiber stirring without obvious agglomeration phenomenon, regarded as uniform mixing. The test blocks were cast in plastic test molds, vibrated, and compacted by shaking table, covered with cling film for 36 h and demolded, and maintained under standard maintenance conditions (relative humidity ≥95%, temperature 20 ± 1 °C) for 28 days, taken out and dried for the test of mechanical properties and thermal conductivity.

Test Methods
The compressive, split strengths, and thermal conductivity of GPCC were tested, and the microstructure images were observed. They are briefly described below.

Strength Test
The compressive strength and split tensile test were conducted in accordance with the "Standard for Test Method of Mechanical Properties on Ordinary Concrete" (GB/T 50081-2019, Chinese standard) [31] using a JYE-2000A type fully-automatic constant-pressure pressure testing machine (see Figure 2a,b) which produced by Beijing Ouya Zhongxing Science Co., Ltd., Beijing, China. The 100 × 100 × 100 mm cubic specimens were prepared to measure the compressive and split tensile strengths. As per the standards, the rate of loading should be controlled for 3 mm/min in the compressive strength and split tensile strength tests.

Thermal Conductivity Test
The thermal conductivity of the GPCC was tested using the "Standard for thermal insulation -Determination of steady-state thermal resistance and related properties -Heat flow meter apparatus" (GB10295-2008, Chinese standard) [32] with a DRE-III multifunctional rapid thermal conductivity testing machine (see Figure 2c) which produced by Xiangtan Xiangyi instrument Co., Ltd., Xiangtan, China. The 300 × 300 × 10 mm cubic specimens were prepared to measure the thermal conductivity. As per the standards, the temperature of the hot side is set on the hot plate side of the instrument and the heat is transferred through the sample to the cold side which is at room temperature, and the

Thermal Conductivity Test
The thermal conductivity of the GPCC was tested using the "Standard for thermal insulation -Determination of steady-state thermal resistance and related properties -Heat flow meter apparatus" (GB10295-2008, Chinese standard) [32] with a DRE-III multifunctional rapid thermal conductivity testing machine (see Figure 2c) which produced by Xiangtan Xiangyi instrument Co., Ltd., Xiangtan, China. The 300 × 300 × 10 mm 3 specimens were prepared to measure the thermal conductivity. As per the standards, the temperature of the hot side is set on the hot plate side of the instrument and the heat is transferred through the sample to the cold side which is at room temperature, and the heat flow transfer is measured by this method. Finally, the thermal conductivity of the GPCC is calculated based on the thickness and heat transfer area of the sample.

Scanning Electron Microscope Test
The micro-structure of the specimen was observed using a scanning electron microscope (FEI INSPECT, F50) which produced by FEI company, Hillsboro, OR, USA. The samples were taken from the test cubes used in the axial compression test, which had a diameter of 4 mm and a thickness of 2 mm. To observe the microscopic morphology of the GHB and the PVA fibers in the concrete, the sample was taken without any coarse aggregate.

Analysis of Range
Range analysis will intuitively show the order of each factor's influence on the evaluation index, which is presented in Table 5 and Figure 3.

Analysis of Range
Range analysis will intuitively show the order of each factor's influence on the evaluation index, which is presented in Table 5 and Figure 3.  For compressive strength of GPCC, the affecting ranking is GHB content (A) > waterbinder ratio (C) > PVA fiber content (B), indicates that the influence of GHB content is  For compressive strength of GPCC, the affecting ranking is GHB content (A) > waterbinder ratio (C) > PVA fiber content (B), indicates that the influence of GHB content is most obvious. As shown in Figure 4a, the compressive strength decreased with the increase of GHB. This is due to the porous cavity structure inside the GHB, and its cylinder compressive strength is lower than that of the matrix, which makes it easy to form penetration joints inside the composite material when it is compressed, accelerating the destruction of the material and leading to the reduction. When the amount of GHB is more than 60%, the breakage rate increases due to the collision between GHB and other materials in the mixing process, which causes the compressive strength dropped significantly. Then, as the main factor affecting the matrix compactness, the effect of water-binder ratio on the compressive strength of GPCC is obvious too, as shown in Figure 4c. Meanwhile, the effect of fiber content is not obvious because the fiber content has little effect on the compactness of the matrix, as shown in Figure 4b. Additionally, the optimal solution is: A1-B3-C1.
For split tensile strength, the affecting ranking is: water-binder ratio (C) > GHB content (A) > PVA fiber content (B), as shown in Figure 5. The effect of water-binder ratio and GHB content is more obvious. Especially for large amounts of GHB (more than 60%), the split tensile strength will decrease rapidly. GHB will reduce the inhibitory effect of fibers on the development of internal pores and micro-cracks in composite. The optimal solution is: A1-B2-C1. than 60%, the breakage rate increases due to the collision between GHB and other materials in the mixing process, which causes the compressive strength dropped significantly. Then, as the main factor affecting the matrix compactness, the effect of water-binder ratio on the compressive strength of GPCC is obvious too, as shown in Figure 4c. Meanwhile, the effect of fiber content is not obvious because the fiber content has little effect on the compactness of the matrix, as shown in Figure 4b. Additionally, the optimal solution is: A1-B3-C1.  For split tensile strength, the affecting ranking is: water-binder ratio (C) > GHB content (A) > PVA fiber content (B), as shown in Figure 5. The effect of water-binder ratio and GHB content is more obvious. Especially for large amounts of GHB (more than 60%), the split tensile strength will decrease rapidly. GHB will reduce the inhibitory effect of fibers on the development of internal pores and micro-cracks in composite. The optimal solution is: A1-B2-C1. For thermal conductivity, the affecting ranking is: GHB content (A) > PVA fiber content (B) > water-binder ratio (C). As shown in Figure 6a, the GPCC thermal conductivity   Figure 4a, the compressive strength decreased with the increase of GHB. This is due to the porous cavity structure inside the GHB, and its cylinder compressive strength is lower than that of the matrix, which makes it easy to form penetration joints inside the composite material when it is compressed, accelerating the destruction of the material and leading to the reduction. When the amount of GHB is more than 60%, the breakage rate increases due to the collision between GHB and other materials in the mixing process, which causes the compressive strength dropped significantly. Then, as the main factor affecting the matrix compactness, the effect of water-binder ratio on the compressive strength of GPCC is obvious too, as shown in Figure 4c. Meanwhile, the effect of fiber content is not obvious because the fiber content has little effect on the compactness of the matrix, as shown in Figure 4b. Additionally, the optimal solution is: A1-B3-C1.  For split tensile strength, the affecting ranking is: water-binder ratio (C) > GHB content (A) > PVA fiber content (B), as shown in Figure 5. The effect of water-binder ratio and GHB content is more obvious. Especially for large amounts of GHB (more than 60%), the split tensile strength will decrease rapidly. GHB will reduce the inhibitory effect of fibers on the development of internal pores and micro-cracks in composite. The optimal solution is: A1-B2-C1. For thermal conductivity, the affecting ranking is: GHB content (A) > PVA fiber content (B) > water-binder ratio (C). As shown in Figure 6a, the GPCC thermal conductivity For thermal conductivity, the affecting ranking is: GHB content (A) > PVA fiber content (B) > water-binder ratio (C). As shown in Figure 6a, the GPCC thermal conductivity decreases and then increases with the increase of GHB, indicating that the reduction effect of GHB on the thermal conductivity of the composite reaches the limit when its dosing is about 80%. With the increase of GHB amount, the content of cement paste in the composite material per unit volume is relatively reduced, and when it is reduced to a limit value, a large number of connected pores and channels from the inside to the surface of unfilled GHB appear in the composite material, so that the closed pore voids are relatively reduced, and then the thermal conductivity will rise. As shown in Figure 6b,c, the fiber content has some effect on the thermal conductivity of GPCC, and the water-binder ratio has the least effect on the thermal conductivity. The optimal solution is: A4-B2-C2.
Based on the range analysis, the content of GHB has the most important influence on the mechanical properties and thermal insulation of GPCC, and the water-binder ratio mainly affects the strength of GPCC by the influence on its matrix. However, the effect of PVA fiber was less than the other factors. tent has some effect on the thermal conductivity of GPCC, and the water-binder ratio has the least effect on the thermal conductivity. The optimal solution is: A4-B2-C2.
Based on the range analysis, the content of GHB has the most important influence on the mechanical properties and thermal insulation of GPCC, and the water-binder ratio mainly affects the strength of GPCC by the influence on its matrix. However, the effect of PVA fiber was less than the other factors.

Variance Analysis
To estimate the importance of each factor more precisely, the results were analyzed by variance analysis in Tables 6-8, to find the mean square value and F-value of each factor.
GHB content has a significant effect on the compressive strength of GPCC, waterbinder ratio and GHB contents have significant effect on the split strength of GPCC, and the influence of GHB content is significant for thermal conductivity of GPCC. As observed, the results are in accordance with range analysis. Although the addition of GHB can play a positive role in improving the thermal insulation performance of GPCC, the high addition of GHB will reduce the strength of GPCC. When the amount of GHB addition is more than 60%, the compressive strength will drop sharply, and when the amount of GHB added is more than 40%, the split tensile strength will drop sharply. The most significant effect of water-cement ratio on tensile split strength, and the split tensile strength of GPCC, can reach high values at low water to glue ratio. The fiber content had little effect on the strength and thermal conductivity of GPCC, especially the split tensile strength.

Variance Analysis
To estimate the importance of each factor more precisely, the results were analyzed by variance analysis in Tables 6-8, to find the mean square value and F-value of each factor. GHB content has a significant effect on the compressive strength of GPCC, waterbinder ratio and GHB contents have significant effect on the split strength of GPCC, and the influence of GHB content is significant for thermal conductivity of GPCC. As observed, the results are in accordance with range analysis. Although the addition of GHB can play a positive role in improving the thermal insulation performance of GPCC, the high addition of GHB will reduce the strength of GPCC. When the amount of GHB addition is more than 60%, the compressive strength will drop sharply, and when the amount of GHB added is more than 40%, the split tensile strength will drop sharply. The most significant effect of water-cement ratio on tensile split strength, and the split tensile strength of GPCC, can reach high values at low water to glue ratio. The fiber content had little effect on the strength and thermal conductivity of GPCC, especially the split tensile strength.

Determination of the Optimum Proportion
The comprehensive balance method was used to analyze the influence of various factors on the performance indexes of GPCC, and finally obtain the optimum proportion. In Figures 4-6, k i represents the arithmetic mean of the experimental results obtained when each factor was taken at level i.
The effect of GHB content (A) on each index can be obtained from Figure 3. The influence of A on compressive strength and thermal conductivity is ranked first and is the leading factor, and the influence on split tensile strength is ranked 2nd and is an important factor. From Figures 4-6, it can be observed that when taking k 2 , GPCC split tensile strength index is the best and compressive strength is basically the same as when taking the maximum index value, thus k 2 is taken. When k 3 is taken, compared with k 2 , GPCC compressive strength increases by 1.72%, GPCC thermal conductivity decreases by 5.64%, PEEC split strength decreases by 23.5%; when k 1 is taken, compared with k 2 , GPCC compressive strength increases by 4.40%, GPCC thermal conductivity increases by 15.92%, GPCC split strength is the same as that when k 2 is taken; when k 4 is taken, the thermal conductivity coefficient is the smallest, but the other three index values are relatively low, thus they are not considered. Combined with the above analysis, the A factor levels are taken as k 2 .
The effect of PVA fiber content (B) on each index can be obtained from Figure 3: B is the second most important factor for the effect on thermal conductivity, and the third most important factor for split tensile strength and compressive strength. From Figures 4-6, the compressive strength, split tensile strength, and thermal conductivity of PEEC obtain the best index at all k 2 , thus the B factor levels are chosen as k 2 .
The effect of water-binder ratio (B) on each index can be obtained from Figure 3. Its influence on compressive strength and tensile strength ranks 2nd and is an important factor, while the influence on thermal conductivity ranks 3rd and is a minor factor. From Figures 4-6, the compressive strength and tensile strength are maximum when k 1 is taken, and the change of water-binder ratio has no effect on the thermal conductivity (compared with the best index k 2 , which is increased by 3%). Therefore, the C factor levels are chosen as k 1 .

Micro-Mechanical Analysis
Discontinuities and micro-cracks within conventional concrete are often weak points. PVA fibers can be used as a joining material to bridge discontinuous areas, not only to reduce discontinuities and micro-cracks within the concrete, but also as a bonding base for the cement. The hydration products from the hydration process are continuously gathered and bonded on the surface of the fiber to fill the gap between the fiber and the substrate, and to strengthen the weak points. As shown in Figure 7, the micro-structure of PVA fiber-reinforced concrete has a three-dimensional mesh distribution of fibers within the matrix. By means of the anchoring effect and bridging effect, it effectively balances the stress generated by the shrinkage of cement paste, reduces the cracks caused by shrinkage, and inhibits or even prevents the development of cracks.
PVA fibers can be used as a joining material to bridge discontinuous areas, not only to reduce discontinuities and micro-cracks within the concrete, but also as a bonding base for the cement. The hydration products from the hydration process are continuously gathered and bonded on the surface of the fiber to fill the gap between the fiber and the substrate, and to strengthen the weak points. As shown in Figure 7, the micro-structure of PVA fiber-reinforced concrete has a three-dimensional mesh distribution of fibers within the matrix. By means of the anchoring effect and bridging effect, it effectively balances the stress generated by the shrinkage of cement paste, reduces the cracks caused by shrinkage, and inhibits or even prevents the development of cracks. The area around the crack of the GPCC compressive specimen was cut and sampled, and the morphology of GPCC after compressive damage was observed by SEM electron microscopy as indicated in Figure 8. PVA fibers are randomly and evenly distributed in the cement matrix, forming a "skeleton" that can effectively disperse the stress and prevent the settlement and cracks of GHB. When macro cracks are created, the fibers can consume some of the energy used to create the cracks, weakening the stress concentration at the crack tip and impeding the growth and development of the cracks. However, a certain number of tiny cracks will be formed near the GHB, near the fibers, and between the GHB and the fibers. With the increase of external force, these tiny cracks will extend along the matrix to the interface of fiber, GHB, and hydration products, or even penetrate the fiber and GHB, causing local stretching and peeling of PVA fibers and shattering inside the GHB, which will lead to the destruction of the material. The area around the crack of the GPCC compressive specimen was cut and sampled, and the morphology of GPCC after compressive damage was observed by SEM electron microscopy as indicated in Figure 8. PVA fibers are randomly and evenly distributed in the cement matrix, forming a "skeleton" that can effectively disperse the stress and prevent the settlement and cracks of GHB. When macro cracks are created, the fibers can consume some of the energy used to create the cracks, weakening the stress concentration at the crack tip and impeding the growth and development of the cracks. However, a certain number of tiny cracks will be formed near the GHB, near the fibers, and between the GHB and the fibers. With the increase of external force, these tiny cracks will extend along the matrix to the interface of fiber, GHB, and hydration products, or even penetrate the fiber and GHB, causing local stretching and peeling of PVA fibers and shattering inside the GHB, which will lead to the destruction of the material.

Conclusions
(1) The content of GHB has a significant effect on the compressive and split tensile strengths and thermal conductivity, the effect of water-cement ratio on split tensile strength is more significant. The PVA content has little effect on the strength and thermal conductivity of GPCC. The optimal ratio was determined as 40% GHB, 1.5% PVA fiber, and 0.26 water-binder ratio. (2) In this experiment, when the content of GHB is greater than 40%, there is a significant reduction in strength, and the effect of fiber is not obvious. It may be that the high doping amount of GHB will have interaction with the PVA fiber, and this problem should be considered in the next research. (3) The change of the GHB content has a significant effect on the mechanical index and thermal conductivity of GPCC. As the GHB content is increased, the compressive strength and tensile strength gradually decrease, and the thermal conductivity starts to rise after a significant decreasing trend. Therefore, further optimization of the GHB content can be considered to reduce the thermal conductivity of GPCC and ensure its mechanical properties. (4) Through micromechanical analysis, the presence of glass beads reduces the bond be-

Conclusions
(1) The content of GHB has a significant effect on the compressive and split tensile strengths and thermal conductivity, the effect of water-cement ratio on split tensile strength is more significant. The PVA content has little effect on the strength and thermal conductivity of GPCC. The optimal ratio was determined as 40% GHB, 1.5% PVA fiber, and 0.26 water-binder ratio. (2) In this experiment, when the content of GHB is greater than 40%, there is a significant reduction in strength, and the effect of fiber is not obvious. It may be that the high doping amount of GHB will have interaction with the PVA fiber, and this problem should be considered in the next research. (3) The change of the GHB content has a significant effect on the mechanical index and thermal conductivity of GPCC. As the GHB content is increased, the compressive strength and tensile strength gradually decrease, and the thermal conductivity starts