Characterization, X-ray Absorption Spectroscopic Analysis and Photocatalytic Activity of Co/Zn Co-Doped TiO2 Nanoparticles Synthesized by One-Step Sonochemical Process

A novel one-step preparation of sonochemical method was applied to synthesize Co/Zn co-doped TiO2 nanoparticles using a sonicator of 750 W, 20 kHz for 30 min at room temperature. The formation of the anatase TiO2 phase for all as-prepared samples was observed from XRD results with a crystalline size in nanoscale. The use of ultrasound allowed for the successful doping of both Co and Zn into the TiO2 lattice, which was confirmed by Synchrotron light including X-ray near edge structure (XANES) and Extended X-ray absorption fine structure (EXAFS) spectroscopy. Ti K-edge, Co K-edge, and Zn K-edge XANES spectra exhibited the dominating +4, +2, and +2 valence state of Ti, Co, and Zn in as-prepared samples, respectively. A detailed XANES and EXAFS data analysis give strong evidence that the Co/Zn dopants partially replace the Ti atom of the TiO2 host. The Co/Zn co-doping extends the light absorption of the host to the visible region and restricts the e+/h+ recombination. The photocatalytic activity of samples was tested for degradation of Rhodamine B dye solution under visible light irradiation. The as-synthesized of the co-doped catalyst was presented as highly efficient, with 2.5 and 5 times dye degradation compared with single-doped and


Introduction
The development of photo-catalyst materials to inactivate pathogenic in aqueous media, degradation of hazardous materials, environmental cleanup, and the purification of pollution in water and air is a matter of growing interest [1]. Particularly, the use of visible light for driving the photocatalytic activity employing solar light is a great challenge. Of the semiconductor photocatalytic materials, titanium dioxide (TiO 2 ) has been the most extensively premeditated and utilized in various applications due to high chemical stability, great oxidizing strength, cheapness, and environmental friendliness [2,3]. However, because of the large energy band gap (3.0-3.2 eV for anatase and rutile phase), TiO 2 can only absorb UV light and is limited as a solar light-driven photocatalyst [4]. In addition, TiO 2 has a high recombination rate between the electron (e − ) and hole (h + ) pairs which results in low quantum yield. Hence, in order to enhance the visible light absorption and to slow down the e − /h + recombination, one of the approaches is to dope with metal/nonmetal, such as Zn, Mn, Co, Fe, Ni, Cu, V, Cr, Mo, Ce, Zr, Au, Y, F, N, I [5][6][7][8][9][10][11][12][13][14][15][16][17][18][19] 2 of 11 and so on. Moreover, recent reports are focused on co-doping of TiO 2 photocatalysts with different ions (metal/metal and metal/nonmetal), allowing better separation of the photogenerated electron and holes, assuring an effective enhancement of visible light adsorption together with higher photocatalytic activity [20][21][22]. Among various metal ions, 3d-transition metals ions such as Zn 2+ and Co 2+ are considered to be the candidate dopants, which the radii ions are similar, and the electronegativity ions are considerably approximate. So, the Co and Zn can enter the lattice of TiO 2 resulting in the improvement of the visible light harvesting and act as the trap for e − /h + pairs resulting in the enhance of charge carrier separation. In the report by J. Cai et al., highly efficient degradation of organic pollutants was presented by the stable boron and cobalt co-doped TiO 2 nanotubes [23]. Photocatalytic degradation of opaque dye acid fuchsin by Pr-Co co-doped TiO 2 was reported by J. Yu [24]. Additionally, detailed atomistic knowledge and local structure are the most important for the understanding of materials functions. X-ray absorption spectroscopy (XAS) is a more specialized technique to examine the local atomic, electronic structure, atomic geometry, and site/symmetry selected density of unoccupied electronic states [25,26]. Many researchers have worked on the development of TiO 2 -based nanoparticles, but most of the work involves the fabrication of nanostructures using conventional methods, these methods providing time-consuming and costly procedures. The facile and clean synthesis using ultrasounds has been confirmed to be useful for fabricating nanostructured materials, with fine dispersion and size reduction of particles. In addition, it prevents agglomeration and uniformly distributes particles [27]. The cavities are created in the solution due to the ultrasonic irradiation, then the cavities collapse after reaching a certain size releasing a large magnitude of energy. Under harsh conditions, various physical changes and reactions occur. So, various nanostructure materials can be successfully formed with desired nanosized. In previous work, we have reported the use of the sonochemical method to prepare nanomaterials at room temperature, such as Mn-Zn co-doped TiO 2 nanoparticles [28], perovskite ZnTiO 3 nanoparticles [29], and Co and Mn-doped ZnTiO 3 nanoparticles [30].
Hence, the present study aimed to investigate the fabrication of Co/Zn co-doped TiO 2 nanoparticles via facile one-step of the sonochemical method. The effect of dopant ions on structural phase, morphology, chemical composition, and optical properties were examined. The local structure of prepared samples was characterized by X-ray absorption near-edge structure and extended X-ray absorption fine structure technique. Rhodamine B dye was considered as a model pollutant to study the photocatalytic degradation capability of the synthesized nanoparticles under visible light irradiation.

Materials and Methods
Titanium isopropoxide (C 12 H 28 O 4 Ti), zinc nitrate hexahydrate (Zn(NO 3 ) 2 ·6H 2 O), and cobalt nitrate hexahydrate (Co(NO 3 ) 2 ·6H 2 O) purchased from Aldrich were used as Ti, Zn and Co precursors, respectively. The molar ratio of Zn dopant was fixed to 1 mol% and varying the Co concentration at 1, 2, 3, and 5 mol%. First, 0.05 M titanium isopropoxide was dissolved in absolute ethanol and zinc nitrate was then added to the solution under a magnetic stirrer for 20 min. After that, the Co at different concentrations was added to the solution followed by DI water. The mixing solution was kept under stirring for 15 min. Finally, the mixed precursor was irradiated under a high ultrasonic sonicator (750 W, 20 kHz) for 30 min at room temperature together with the slow addition of NaOH solution (6g of NaOH pallet in 20 mL of DI) until the precipitation solution was obtained. The obtained solution was washed thoroughly with deionized water until the pH became 7 and then dried at 120 • C for 12 h. Finally, as-synthesized TiO 2 nanopowders were obtained.
Phase structure of as-synthesized samples was characterized by the X-ray diffraction technique (XRD). Surface morphology and particles size analysis were obtained by the Schottky field emission scanning electron microscope (FESEM) model: SU8230. The UVvisible diffused reflection spectroscopy (UV-vis DRS) model: Perkin Elmer model Lamda 750s was used to study the optical properties of all samples. The chemical composition Crystals 2021, 11, 1254 3 of 11 of samples was obtained by the X-ray absorption spectroscopy (XAS) technique at Ti, Zn, and Co K-edge using Beamline-8, Synchrotron Light Research Institute (SLRI) Thailand, with the storage ring running at 1.2 GeV and beam current of beam current 80-120 mA. The data collection was carried out in transmission mode for Ti K-edge (at 4966 eV) and fluorescent mode for Zn K-edge (9659 eV) and Co K-edge (7709 eV) using double crystal Ge(220) monochromator. ATHENA and ATHEMIS programs were used for all XAS analyses. The specific area of prepared samples was measured by the surface area and pore size analyzer, Quantachrome, model: Autosorb iQ-C-XR. The photocatalytic behavior of prepared samples was evaluated using RhB degradation as a test reaction. In a typical, the photocatalytic performance was evaluated by the degradation of Rhodamine B (0.01 mmol) dye in an aqueous solution under visible light irradiation. The 0.08 g of catalyst was added to 100 mL of dye solution, the suspension was stirred for 20 min in the dark to ensure the establishment of adsorption/desorption between dye and catalyst, and then the visible light was irradiated. During the photocatalytic reaction, 4 mL of dye solution was taken at selected time intervals. The concentration of RhB in the supernatants was measured by UV-vis spectroscopy at a wavelength of 554 nm.

Phase Structure
The crystallographic structures of as-synthesized pure TiO 2 , single-doping, and codoping nanopowders prepared by the single-step sonochemical method were confirmed by XRD investigation as seen in Figure 1. The diffraction position of 2θ at 25.3 • , 37.6 • , 48.1 • , and 54.1 • corresponded to the (101), (112), (200), and (105) crystallographic planes of the anatase-TiO 2 phase, respectively. All XRD diffractograms of co-doping samples clearly exhibit the formation of pure anatase TiO 2 phase without any secondary phase of metal oxide. By the increase in the cobalt content in TiO 2 samples, the intensities of the main anatase phase slightly declined, and the width of diffraction peaks of 101 became broader, clearly representing the reduction of the crystalline size. These may have indicated the shrinkage of some of the TiO 2 lattices caused by the incorporation of the doped Co/Zn ions. From the results, it can be proposed the sonochemical reaction mechanism that the hydrolytic species of TTIP in water condensed to form a large number of tiny gel nuclei, which aggregated to form larger clusters. Ultrasonic irradiation from the sonicator generates a lot of local hot spots within the solution, outside which the polycondensation of ≡Ti-OH or ≡Ti-OR is promoted [31]. The local hot spot is an important role in the rapid loss of organic residue and water. This further causes the formation of a large number of seed nuclei, which leads to smaller grain size. In this case, the preferred region for TiO 2 crystallization is the interfacial zone of the ultrasound cavity, which is due to the low vapor pressure of the reactants. Compared with the traditional stirring technology, sonochemistry has been demonstrated to stimulate the speed of the reaction in liquid. Hence, high intensity of ultrasounds can accelerate the crystallization of TiO 2 , and nanocrystalline products were obtained without the heat-treatment process.

Structural Study
The XAS technique with synchrotron light including X-ray absorption near edge structure (XANES) and extended X-ray absorption fine structure (EXAFS) was used to investigate the electronic nature of Co/Zn co-doped TiO 2 samples. The normalized XANES spectra of single-doped, co-doped TiO 2 and the reference standards are shown in Figure 2. Generally, the interpretation of Ti K-edge is intricate, of which the main features of postedge edge (>4980 eV) can be determined to dipole transition from Ti 1s → 4p states, whereas the pre-edge (<4980 eV) can be assigned to the electronic transition to the crystal field split hybridized states between Ti 4p and 3d orbital based on a mixture of quadrupole and dipole excitations [6]. By examining these data and comparing with the literature, as displayed in Figure 2a, the Ti K-edge for TiO 2 , single-doping, and co-doping samples describes the pre-edge spectra of anatase TiO 2 based specimens including four characteristic spectra denoted as A 1 , A 2 , A 3 , and B in the energy region of 4988-4996 eV. The pre-edge Ti K-edge XANES structure arises from 1s to 4d dipole electric transition, with the intensities of the peaks affected by the local geometry and particular medium-range structure of the sample around central Ti atoms [6]. Moreover, the features of pre-edge such as height and position indicate that these samples contain hexa-coordinated Ti 4+ atoms. The partial split of pre-edge spectra of Ti K-edge could be observed in the first derivative XANES as written in Figure 2b, representing the edge raising of structures, which has been discussed above.

Structural Study
The XAS technique with synchrotron light including X-ray absorption near edge structure (XANES) and extended X-ray absorption fine structure (EXAFS) was used to investigate the electronic nature of Co/Zn co-doped TiO2 samples. The normalized XANES spectra of single-doped, co-doped TiO2 and the reference standards are shown in Figure 2. Generally, the interpretation of Ti K-edge is intricate, of which the main features of post-edge edge (>4980 eV) can be determined to dipole transition from Ti 1s → 4p states, whereas the pre-edge (<4980 eV) can be assigned to the electronic transition to the crystal field split hybridized states between Ti 4p and 3d orbital based on a mixture of quadrupole and dipole excitations [6]. By examining these data and comparing with the literature, as displayed in Figure 2a, the Ti K-edge for TiO2, single-doping, and co-doping samples describes the pre-edge spectra of anatase TiO2 based specimens including four characteristic spectra denoted as A1, A2, A3, and B in the energy region of 4988-4996 eV. The pre-edge Ti K-edge XANES structure arises from 1s to 4d dipole electric transition, with the intensities of the peaks affected by the local geometry and particular mediumrange structure of the sample around central Ti atoms [6]. Moreover, the features of preedge such as height and position indicate that these samples contain hexa-coordinated Ti 4+ atoms. The partial split of pre-edge spectra of Ti K-edge could be observed in the first derivative XANES as written in Figure 2b, representing the edge raising of structures, which has been discussed above. To confirm the existence of Co and Zn dopants ions in TiO 2 lattice, Co-and Zn Kedge XANES measurements were conducted. For the Zn K-edge, the normalized XANES spectra and the first derivative of prepared samples and ZnO reference standard are shown in Figure 2c,d, respectively. Following the inspection of the spectra, it was found that the spectra exhibit a strong absorption edge in a range of 9660-9670 eV with no pre-edge region because the 3d orbital in Zn 2+ ion is fully occupied by electrons. The energy absorption spectra of all samples correspond to the Zn 2+ of the ZnO reference standard. Thus, the Zn species being introduced into the TiO2 host is evidently present in a 2+ oxidation state. In the case of Co K-edge, as seen in Figure 2e,f, normalized XANES spectra and their first derivative of all as-prepared samples reveals the main absorption energy at~7710 eV corresponding to the transition to higher energy levels. The strong absorption edge of the co-doped sample corresponds to the CoO reference standard. It can be concluded that prepared samples comprise Co 2+ of oxidation state. Moreover, both post-edge spectra of Zn K-edge (after 9670 eV) and Co K-edge (after 7730 eV) are not likely to occur ZnO and CoO standard spectrum, respectively, which is presumed the Zn 2+ and Co 2+ cations partially replaced Ti 4+ cations to octahedrally coordinated with six oxygen anions. However, the Co-dopants do not exhibit the changing in pre-and post-edge of XANES feature, this implies that the dopant ion might not change the host structure but be incorporated in the TiO 2 host. To confirm the existence of Co and Zn dopants ions in TiO2 lattice, Co-and Zn Kedge XANES measurements were conducted. For the Zn K-edge, the normalized XANES spectra and the first derivative of prepared samples and ZnO reference standard are shown in Figure 2c,d, respectively. Following the inspection of the spectra, it was found that the spectra exhibit a strong absorption edge in a range of 9660-9670 eV with no preedge region because the 3d orbital in Zn 2+ ion is fully occupied by electrons. The energy absorption spectra of all samples correspond to the Zn 2+ of the ZnO reference standard. Thus, the Zn species being introduced into the TiO2 host is evidently present in a 2+ oxidation state. In the case of Co K-edge, as seen in Figure 2e,f, normalized XANES spectra and their first derivative of all as-prepared samples reveals the main absorption energy at ~7710 eV corresponding to the transition to higher energy levels. The strong absorption edge of the co-doped sample corresponds to the CoO reference standard. It can be concluded that prepared samples comprise Co 2+ of oxidation state. Moreover, both postedge spectra of Zn K-edge (after 9670 eV) and Co K-edge (after 7730 eV) are not likely to occur ZnO and CoO standard spectrum, respectively, which is presumed the Zn 2+ and Co 2+ cations partially replaced Ti 4+ cations to octahedrally coordinated with six oxygen anions. However, the Co-dopants do not exhibit the changing in pre-and post-edge of XANES feature, this implies that the dopant ion might not change the host structure but be incorporated in the TiO2 host.
For an in-depth elucidation of the local structure in as-prepared samples, the EXAFS inquisition was employed at Ti K-edge, Zn K-edge, and Co-kedge. EXAFS spectra are For an in-depth elucidation of the local structure in as-prepared samples, the EXAFS inquisition was employed at Ti K-edge, Zn K-edge, and Co-kedge. EXAFS spectra are Fourier-transformed (FT) with k 2 -weighting to produce radial distribution functions, as shown in Figure 3. By analysis of Ti as an absorber atom for TiO 2 , there are two peaks appearing at around 1.9 Å and 2.7 Å (Black line). The first peak is the Ti-O coordination, associating with the single scattering path of absorbing Ti atom with the nearest neighboring O atoms by six-coordinated around the Ti atom. While the second peak is the Co/Zn-Ti coordination assigned to the single and multiple scattering paths of the absorbing Ti atom with the nearest neighboring Ti atoms and with the nearest neighboring Co/Zn atoms. For describing the environment around Zn-and Co-dopants ions, FT spectra of co-coped samples at Zn and Co were analyzed. It can be seen that the radial distribution features for the Zn/Co dopants in all TiO 2 samples studied are similar to the Ti in TiO 2 . This indicates that the environment around dopant ions is identical with the host Ti, which can be implied the Zn/Co dopants replaced in the Ti site of samples.

Morphology and Surface Area Analysis
The FESEM images of single-doped and co-doped samples are displayed in Figure 4. As shown in Figure 4a, almost spherical-shaped particles with particle agglomeration were observed in the single Zn doped TiO 2 samples. For 3% and 5% co-doping samples (Figure 4b,c), FESEM images exhibit the uniform distribution of nanoparticles, especially the Co-3%, as seen in Figure 4b. In addition, the micrograph in Figure 4d demonstrated that the particle size analysis by FESEM image, the average particle sizes are around 10-20 nm.
ing Ti atom with the nearest neighboring Ti atoms and with the nearest neighboring Co/Zn atoms. For describing the environment around Zn-and Co-dopants ions, FT spectra of co-coped samples at Zn and Co were analyzed. It can be seen that the radial distribution features for the Zn/Co dopants in all TiO2 samples studied are similar to the Ti in TiO2. This indicates that the environment around dopant ions is identical with the host Ti, which can be implied the Zn/Co dopants replaced in the Ti site of samples.

Morphology and Surface Area Analysis
The FESEM images of single-doped and co-doped samples are displayed in Figure 4. As shown in Figure 4a, almost spherical-shaped particles with particle agglomeration were observed in the single Zn doped TiO2 samples. For 3% and 5% co-doping samples (Figure 4b,c), FESEM images exhibit the uniform distribution of nanoparticles, especially the Co-3%, as seen in Figure 4b. In addition, the micrograph in Figure 4d demonstrated that the particle size analysis by FESEM image, the average particle sizes are around 10-20 nm.
For the specific area of all as-prepared samples, N2 adsorption-desorption and corresponding pore size distribution calculated by BJH (TiO2-Zn/Co-3%) are shown in Figure  5a,b, respectively. It can be seen that the single-and co-doping shows isotherm of type II,   For the specific area of all as-prepared samples, N 2 adsorption-desorption and corresponding pore size distribution calculated by BJH (TiO 2 -Zn/Co-3%) are shown in  Figure 5a,b, respectively. It can be seen that the single-and co-doping shows isotherm of type II, which is a typical medium microporous structure. The surface area of Zn-TiO 2 , 1%-Co/Zn-TiO 2 , 3%-Co/Zn-TiO 2 , and 5%-Co/Zn-TiO 2 are 190. 86, 201.77, 205.27, 206.40, 208.83 m 2 /g, respectively. The large surface of co-doped samples compared to pure-, single-doped, and previous studies may increase the interaction in photocatalytic activity, which is beneficial for photo photocatalytic efficiency.

Optical Properties
The UV-vis DRS measurement of pure TiO2, single-doped, and co-doped samples is shown in Figure 6. For the single-doped samples, extended visible light absorption is observed compared to pure TiO2. Furthermore, the larger absorption in the visible region is noticed in the co-doped samples. It is suggested that increasing co-dopant concentration could result in the reduction of bandgap energy and the enhancement in visible lightharvesting of TiO2. This feature would be correlated to the incorporation of dopant ions in the host lattice that could generate new electronic states in the TiO2 bandgap. Hence the

Optical Properties
The UV-vis DRS measurement of pure TiO 2 , single-doped, and co-doped samples is shown in Figure 6. For the single-doped samples, extended visible light absorption is observed compared to pure TiO 2 . Furthermore, the larger absorption in the visible region is noticed in the co-doped samples. It is suggested that increasing co-dopant concentration could result in the reduction of bandgap energy and the enhancement in visible light-harvesting of TiO 2 . This feature would be correlated to the incorporation of dopant ions in the host lattice that could generate new electronic states in the TiO 2 bandgap. Hence the distance of charge transfers between the d electron of the dopant ion and the conduction or valence band is narrowed, leading to the increase in visible light response of the material. Moreover, the different valence states of dopants including Co 2+ and Zn 2+ from the host matrix Ti 4+ may induce the substantial generation of oxygen deficiencies. The bandgap energies of all samples were calculated from the DRS spectra employing a modified Kubelka-Munk equation as plotted in Figure 6b. It is obviously noticed that the deposition of co-dopants significantly affects the decrease of the bandgap energy of the host TiO 2 which has an estimated value of 3.21, 3.01, 2.78, 2.75, 2.72, and 2.68 eV for pure TiO 2 , Zn-TiO 2 , 1%Co/Zn-TiO 2 , 3%Co/Zn-TiO 2 , and 5%Co/Zn-TiO 2 , respectively. From these results, it was inferred that the Co/Zn co-doped TiO 2 could be activated effectively under visible light illumination.

Photocatalytic Activity
The photocatalytic performance of the prepared samples was employed for rhodamine b dye decolorization under visible light irradiation. Pure RhB exhibit the absorption band at 544 nm, which is assigned to the chromophoric group. The percentage of degradation (D) for RhB dye was calculated using the following equation; where A 0 is the absorbance value of the initial RhB solution, A t is the absorbance value of degraded RhB solution at the reaction time t. Under the visible light irradiation without the catalyst, no decrease in the RhB concentration is observed, implying that the self-photolysis of RhB is negligible when irradiated with visible light. When the reaction was carried out by a single doped sample, around 40% of RhB degradation after 90 min was obtained a seen in Figure 6. For the Co/Zn co-doped TiO 2 (Figure 7a), the superior degradation of around 80% was found in the samples containing 3% of Co-content after 90 min of irradiation time while the sample with 1, 2, and 5% Co doping content exhibited about 51, 73 and 71% of photodecolorization, respectively. According to the results, all as-synthesized co-doped catalysts show higher degradation rates than Co-and Zn-single-doped and bare TiO 2 . Obviously, a comparison in the plots of dye degradation shows that the concentration of as-prepared catalyst can indeed influence the degradation efficiency. The increase of dopant content to 3 mol% resulted in the increase in dye degradation, which might be attributed to the Co increased, the surface barrier becomes higher and narrower space charge obtained, leading to easy of e/h pairs. However, a slight decrease of dye decomposition was observed when the concentration of Co-doped was further increased to 5mol%, this may be due to when the content of cobalt dopant is increased beyond the limit, the space charge recombination is lower and penetration depth of light into the catalyst greatly exceeds the layer of space charge, indicating in high recombination of e/h pairs [32].

Photocatalytic Activity
The photocatalytic performance of the prepared samples was employed for rhodamine b dye decolorization under visible light irradiation. Pure RhB exhibit the absorption band at 544 nm, which is assigned to the chromophoric group. The percentage of degradation (D) for RhB dye was calculated using the following equation; where A0 is the absorbance value of the initial RhB solution, At is the absorbance value of degraded RhB solution at the reaction time t. Under the visible light irradiation without the catalyst, no decrease in the RhB concentration is observed, implying that the self-photolysis of RhB is negligible when irradiated with visible light. When the reaction was carried out by a single doped sample, around 40% of RhB degradation after 90 min was obtained a seen in Figure 6. For the Co/Zn co-doped TiO2 (Figure 7a), the superior degradation of around 80% was found in the samples containing 3% of Co-content after 90 min of irradiation time while the sample with 1, 2, and 5% Co doping content exhibited about 51, 73 and 71% of photo-decolorization, respectively. According to the results, all as-synthesized co-doped catalysts show higher degradation rates than Co-and Zn-single-doped and bare TiO2. Obviously, a comparison in the plots of dye degradation shows that the concentration of as-prepared catalyst can indeed influence the degradation efficiency. The increase of dopant content to 3 mol% resulted in the increase in dye degradation, which might be attributed to the Co increased, the surface barrier becomes higher and narrower Crystals 2021, 11, x FOR PEER REVIEW 9 of 12 decomposition was observed when the concentration of Co-doped was further increased to 5mol%, this may be due to when the content of cobalt dopant is increased beyond the limit, the space charge recombination is lower and penetration depth of light into the catalyst greatly exceeds the layer of space charge, indicating in high recombination of e/h pairs [32].
Reaction kinetics gives information about the reaction rates and the mechanisms by which the reactants are converted to the products. The equation for pseudo-first-order kinetic is given below; where C and C0 are the final and initial concentrations (ppm) of RhB, k is the apparent reaction rate constant (min −1 ) and t is the irradiation time (min). Figure 7b demonstrates the photocatalytic reaction kinetic of RhB degradation in the solution based on the data plotted in Figure 6. As it can be seen, a rather good correlation to pseudo-first-order reaction kinetics (R 2 = 0.97) was found, which suggests that the RhB degradation over these samples follows the first-order kinetics. Among all as-prepared catalysts, 3% of Co/Zn doped TiO2 shows the highest reaction rate constant of 0.0114 min −1 , which is about 5.2 and 2.6 times that over pure and single-doping catalysts, respectively. It is observed that the superior performance of organic compounds photodegradation was found in Co/Zn co-doping TiO2. It may be due to many factors, such as the increase of visible light harvesting due to the narrowing energy band gap, slower time for e -/h + pairs recombination, and greater hydroxyl radical generation. Additionally, the pos-  Reaction kinetics gives information about the reaction rates and the mechanisms by which the reactants are converted to the products. The equation for pseudo-first-order kinetic is given below; where C and C 0 are the final and initial concentrations (ppm) of RhB, k is the apparent reaction rate constant (min −1 ) and t is the irradiation time (min). Figure 7b demonstrates the photocatalytic reaction kinetic of RhB degradation in the solution based on the data plotted in Figure 6. As it can be seen, a rather good correlation to pseudo-first-order reaction kinetics (R 2 = 0.97) was found, which suggests that the RhB degradation over these samples follows the first-order kinetics. Among all as-prepared catalysts, 3% of Co/Zn doped TiO 2 shows the highest reaction rate constant of 0.0114 min −1 , which is about 5.2 and 2.6 times that over pure and single-doping catalysts, respectively. It is observed that the superior performance of organic compounds photodegradation was found in Co/Zn co-doping TiO 2 . It may be due to many factors, such as the increase of visible light harvesting due to the narrowing energy band gap, slower time for e − /h + pairs recombination, and greater hydroxyl radical generation. Additionally, the possible mechanism of photodegradation for organics compounds using metal-doped TiO 2 was studied by comparing with similarly reported [33][34][35][36]. They reported that when the light irradiation on the metal-doped TiO 2 catalyst, photoexcited electrons were transferred from the valence band to newly created electronic states in the band structure via metals incorporated into the TiO 2 matrix. Then, the transferred electron reacted with an oxygen molecule (O 2 ) to generate a superoxide anion ·O − 2 ; e − + O 2 → ·O − 2 , and a positive hole in the valence band of TiO 2 reacted with (i) a water molecule (H 2 O) or (ii) hydroxyl ion (OH − ) to form a hydroxyl radical (·OH); (i) h + + H 2 O → ·OH + H + and (ii) h + + OH − → ·OH . Finally, the reactive species ·O − 2 and ·OH could oxidize the target organic compounds to generate CO 2 , CO, and other byproducts.

Conclusions
In summary, Co/Zn co-doped TiO 2 was successfully synthesized by a facile onestep sonochemical method at room temperature. The use of ultrasounds allowed for the successful doping of both Co and Zn into the TiO 2 lattice, which caused a shift in the light absorption toward the higher wavelength. XANES measurement confirmed the oxidation state of 4+, 2+, and 2+ for Ti, Zn, and Co, respectively. EXAFS analysis reveals that the cobalt and zinc are possibly occupied into TiO 2 lattice, by replacing some Ti 4+ . The Co/Zn co-doped TiO 2 photocatalyst exhibited good photodegradation of RhB dye under visible light irradiation. The best decolorization performance was achieved in the content of 3% for cobalt doping concentration. It is presumed that (i) the sonochemical method provides the small nanoparticles resulting in higher surface area and (ii) the incorporation of Co and Zn lead to enhance visible light harvesting and to diminish the electron-hole recombination, which improved the photocatalytic behavior.