Ceria Nanoparticles ’ Morphological Effects on the N 2 O Decomposition Performance of Co 3 O 4 / CeO 2 Mixed Oxides

Ceria-based oxides have been widely explored recently in the direct decomposition of N2O (deN2O) due to their unique redox/surface properties and lower cost as compared to noble metal-based catalysts. Cobalt oxide dispersed on ceria is among the most active mixed oxides with its efficiency strongly affected by counterpart features, such as particle size and morphology. In this work, the morphological effect of ceria nanostructures (nanorods (NR), nanocubes (NC), nanopolyhedra (NP)) on the solid-state properties and the deN2O performance of the Co3O4/CeO2 binary system is investigated. Several characterization methods involving N2 adsorption at −196 ◦C, X-ray diffraction (XRD), temperature programmed reduction (TPR), X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM) were carried out to disclose structure–property relationships. The results revealed the importance of support morphology on the physicochemical properties and the N2O conversion performance of bare ceria samples, following the order nanorods (NR) > nanopolyhedra (NP) > nanocubes (NC). More importantly, Co3O4 impregnation to different carriers towards the formation of Co3O4/CeO2 mixed oxides greatly enhanced the deN2O performance as compared to bare ceria samples, without, however, affecting the conversion sequence, implying the pivotal role of ceria support. The Co3O4/CeO2 sample with the rod-like morphology exhibited the best deN2O performance (100% N2O conversion at 500 ◦C) due to its abundance in Co2+ active sites and Ce3+ species in conjunction to its improved reducibility, oxygen kinetics and surface area.


Introduction
Nitrous oxide (N 2 O) is one of the most significant greenhouse gases contributing to the depletion of the ozone layer.N 2 O has a much higher global warming potential (GWP) compared to CO 2 (310 times higher) and a long atmospheric lifetime (114 years).The emissions of N 2 O are derived by both natural and anthropogenic sources.The main anthropogenic sources for N 2 O emissions involve agriculture (use of fertilizers), chemical industry (adipic and nitric acid production), the combustion of fossil fuels, as well as biomass burning, etc. [1][2][3][4].
Among the different transition metal oxides, cobalt spinel shows unique physicochemical characteristics, such as thermal stability and high reducibility, making it an excellent candidate for the deN 2 O process [15,23,29,30].However, the high cost of cobalt renders mandatory its dispersion to high surface area supports like ceria, magnesia, etc. [31,32].Among the various supports investigated, ceria exhibits unique redox properties associated with its high oxygen storage capacity (OSC), rendering this material highly effective in many catalytic processes [23,[33][34][35].Furthermore, the synergistic effects induced by strong metal-ceria interactions, in nanoscale, can modify the surface chemistry of the materials through geometric or/and electronic perturbations, leading to improved redox properties and catalytic activity [36][37][38][39][40].
However, the catalytic efficiency of transition metal oxides, involving ceria-based mixed oxides, can be considerably affected by the different counterpart characteristics, such as particle size and morphology.In this regard, engineering the particle size and shape (e.g., nanorods and nanocubes) through the employment of advanced nano-synthesis paths has lately received particular attention [33,[41][42][43].Interestingly, the support morphology greatly affects the redox properties, oxygen mobility and, subsequently, the catalytic activity of the mixed oxides.For instance, Lin et al. [44] prepared Co 3 O 4 /CeO 2 catalysts with three different support morphologies, namely polyhedra, nanorods and hexagonal shapes, with polyhedra exhibiting the highest catalytic activity for ammonia synthesis.In a similar manner, by tailoring the support morphology, CuO/CeO 2 nanoshaped materials of enhanced reducibility and deN 2 O performance can be obtained [45].Andrade-Martínez et al. [46] investigated the catalytic reduction of N 2 O over CuO/SiO 2 catalysts, revealing the key role of the spherical ordered mesoporous support, along with its functionalization through copper addition, on the improved catalytic activity and stability, making this material comparable to noble metal-reported systems.Different support morphologies (rods, plates and cubes) have also been employed for the low temperature CH 2 Br 2 oxidation revealing the superiority of cobalt-ceria nanorods in the catalytic performance [47].Moreover, cobalt oxide supported on ceria of different morphology (nanoparticles, nanorods and nanocubes) has been investigated for the catalytic oxidation of toluene with the nanoparticles exhibiting the highest catalytic activity due to the synergism at the interface between the two oxide phases, which leads to an improved reducibility [48].Very recently, the influence of support morphology (nanorods, nanocubes and nanopolyhedra) on the surface and structural properties of CuO/CeO 2 mixed oxide has been thoroughly explored through both in situ and ex situ characterization techniques.The results disclosed the significance of the ceria morphology on the reducibility and oxygen kinetics, revealing the order nanorods > nanopolyhedra > nanocubes [49].
In this work, ceria structures of various morphologies (nanopolyhedra, nanorods and nanocubes) were hydrothermally prepared, and then cobalt was impregnated into the above ceria supports.The purpose of this work was to explore the impact of support morphology on the surface chemistry and the deN 2 O performance of Co 3 O 4 /CeO 2 mixed oxides.The results clearly revealed that support morphology can exert a profound influence on the N 2 O decomposition, paving the way toward the rational design of highly efficient deN 2 O catalysts.

Textural/Structural Analysis (BET and XRD)
The main textural and structural characteristics of bare ceria samples and Co 3 O 4 /CeO 2 mixed oxides (hereinafter denoted as Co/CeO 2 ) are summarized in Table 1.According to the BET surface area, the following order is acquired: CeO 2 -NP (88 m 2 g −1 ) > CeO 2 -NR (79 m 2 g −1 ) > CeO 2 -NC (37 m 2 g −1 ).The addition of cobalt into CeO 2 decreases the surface area, without, however, significantly affecting the order obtained for bare ceria samples.The Co/CeO 2 -NR sample exhibits the highest value (72 m 2 g −1 ) succeeded by Co/CeO 2 -NP (71 m 2 g −1 ) and Co/CeO 2 -NC (28 m 2 g −1 ).Regarding the average pore diameter and pore volume, they both decreased upon the addition of Co to ceria nanorods and nanocubes.However, concerning ceria nanopolyhedra, the addition of cobalt leads to a small increase in the average pore diameter, whereas the pore volume is not significantly affected (Table 1).Figure 1a shows the Barret-Joyner-Halenda (BJH) desorption pore size distributions (PSD) of bare ceria and Co/CeO 2 catalysts.According to the pore size distribution, all the samples have their maxima at a pore diameter more than 3 nm, designating the presence of mesopores [50].It is obvious that bare ceria samples with the nanocube (CeO 2 -NC) and nanorod morphology (CeO 2 -NR) exhibit similar particle size distributions, whereas in ceria nanopolyhedra (CeO 2 -NP), a narrower PSD is observed.Noteworthily, PSD remains practically unaffected by the addition of cobalt in all cases.As it can be observed in Figure 1b which shows the adsorption-desorption isotherms, all samples demonstrate type IV isotherms with a hysteresis loop at a relative pressure > 0.5, further corroborating the mesoporous structure of the materials [51,52].
The XRD patterns of the samples are shown in Figure 2. The main peaks can be indexed to (111), (200), (220), (311), (222), (400), (331), (420), (422), (511) and (440) planes which are attributed to ceria face-centered cubic fluorite structure (Fm3m symmetry, no.225) [53,54].There are three small peaks at 2θ values of approx.36, 44 and 64 o which are typical of Co 3 O 4 [33].These three diffraction peaks correspond to the (311), (400) and (440) planes of Co 3 O 4 , respectively.The average crystallite diameter of the oxide phases (CeO 2 and Co 3 O 4 ) was assessed by an XRD analysis by means of the Williamson-Hall plot (Table 1).The CeO 2 crystallite size measurements showed 24, 14 and 11 nm for Co/CeO 2 -NC, Co/CeO 2 -NR and Co/CeO 2 -NP, respectively.As it is obvious from Table 1, there is a small decrease in the ceria crystallite size for nanocubes and nanorods, whereas no changes were observed for nanopolyhedra, indicating that the structural characteristics of ceria supports do not get significantly affected upon cobalt addition, as it will be further corroborated by a TEM analysis (see below).In a similar manner, the BET analysis (Table 1) indicates no significant modifications on the pore characteristics of ceria nanopolyhedra upon cobalt addition, which could be ascribed to their irregular morphology.It should be also noted that the samples with nanocube morphology exhibit the smallest BET surface area and the largest CeO 2 and Co 3 O 4 crystallite sizes in comparison to nanorods and nanopolyhedra.As for the crystallite size of cobalt oxide phase, the following sequence was obtained: Co/CeO 2 -NC (19 nm) > Co/CeO 2 -NR (16 nm) > Co/CeO 2 -NP (15 nm), which perfectly matches the order obtained for CeO 2 .pore characteristics of ceria nanopolyhedra upon cobalt addition, which could be ascribed to their irregular morphology.It should be also noted that the samples with nanocube morphology exhibit the smallest BET surface area and the largest CeO2 and Co3O4 crystallite sizes in comparison to nanorods and nanopolyhedra.As for the crystallite size of cobalt oxide phase, the following sequence was obtained: Co/CeO2-NC (19 nm) > Co/CeO2-NR (16 nm) > Co/CeO2-NP (15 nm), which perfectly matches the order obtained for CeO2.

Morphological Characterization (TEM)
Transmission electron microscopy (TEM) has been applied so as to examine the morphological differences among the materials.Figure 3a-c shows the TEM images of ceria supports.The CeO2-NR sample (Figure 3a) exhibits a rod-shaped morphology with the length varying between 25 and 200 nm. Figure 3b and c demonstrates mainly irregular-shaped nanopolyhedra and cubes, respectively.Figure 3d-f illustrates the images derived by TEM analysis for the Co/CeO2 mixed oxides.Evidently, the morphology is not affected by cobalt addition to the ceria carrier.

Morphological Characterization (TEM)
Transmission electron microscopy (TEM) has been applied so as to examine the morphological differences among the materials.Figure 3a-c shows the TEM images of ceria supports.The CeO 2 -NR sample (Figure 3a) exhibits a rod-shaped morphology with the length varying between 25 and 200 nm. Figure 3b and c demonstrates mainly irregular-shaped nanopolyhedra and cubes, respectively.Figure 3d-f illustrates the images derived by TEM analysis for the Co/CeO 2 mixed oxides.Evidently, the morphology is not affected by cobalt addition to the ceria carrier.

Redox Properties (H2-temperature programmed reduction (TPR))
H2-TPR experiments took place to investigate the ceria shape effect on the redox properties of as-prepared samples.Figure 4a shows the TPR profiles of bare ceria samples, consisting of two wideranging peaks which are centred at 526-551 °C and 789-813 °C.These peaks are attributed to ceria surface oxygen (Os) and bulk oxygen (Ob) reduction, respectively [33,49,55].In Table 2, the hydrogen consumption corresponding to surface oxygen as well as to bulk oxygen reduction is presented.Based on the ratio of surface-to-bulk oxygen (Os/Ob), the following order was acquired: CeO2-NR

Redox Properties (H 2 -Temperature Programmed Reduction (TPR))
H 2 -TPR experiments took place to investigate the ceria shape effect on the redox properties of as-prepared samples.Figure 4a shows the TPR profiles of bare ceria samples, consisting of two wide-ranging peaks which are centred at 526-551 • C and 789-813 • C.These peaks are attributed to ceria surface oxygen (O s ) and bulk oxygen (O b ) reduction, respectively [33,49,55].In Table 2, the hydrogen consumption corresponding to surface oxygen as well as to bulk oxygen reduction is presented.Based on the ratio of surface-to-bulk oxygen (O s /O b ), the following order was acquired: CeO 2 -NR (1.13) > CeO 2 -NP (0.94) > CeO 2 -NC (0.71).This indicates the superior reducibility of the rod-shaped sample as it exhibits the highest amount of loosely bound oxygen species.The latter is expected to notably affect the deN 2 O process, where the desorption of adsorbed oxygen species mainly determines the reaction rate (vide infra).The reduction profiles of the Co/CeO 2 samples as well as the one of a Co 3 O 4 reference are shown in Figure 4b.Table 2 summarizes the main TPR peaks along with the hydrogen consumption (mmol H 2 g −1 ).Pure Co 3 O 4 shows two reduction peaks (a and b) in much lower temperatures than those of bare ceria samples, namely 305 • C and 415 • C.They are ascribed to the stepwise reduction of Co 3 O 4 → CoO → Co, respectively [44,[56][57][58].
On the other hand, Co/CeO 2 samples exhibit two main peaks at the temperature range of 318-335 • C (peak a) and 388-405 • C (peak b), ascribed to the reduction of Co 3+ to Co 2+ and Co 2+ to Co 0 , respectively [33,59,60].Obviously, the cobalt addition facilitates the reduction of ceria surface oxygen, shifting the peaks centered at 526-551 • C to a lower temperature (comparison of Figure 4a,b).They also exhibit a broad peak above 800 • C, attributed to the ceria subsurface oxygen reduction, while the capping oxygen reduction overlaps with the reduction of CoO [33,56,61].Apparently, the reduction of the mixed oxides takes place in lower temperatures compared to the bare ceria samples, demonstrating the beneficial effect of cobalt on the surface oxygen reduction of ceria.In fact, the interaction between the two oxide phases could be considered responsible for the improved reducibility and oxygen mobility, as thoroughly discussed in previous studies [48,49,62].According to the consumption of hydrogen in the low-temperature range (Table 2), which could be related to the cobalt species reduction along with the ceria surface oxygen reduction, the Co/CeO 2 -NP and Co/CeO 2 -NR samples exhibit a similar H 2 uptake (about 2.40 mmol H 2 g −1 ) while the sample of nanocube morphology exhibits a much lower value (2.05 mmol H 2 g −1 ).This trend is well-matched to the catalytic results (vide infra), revealing the key role of redox ability on the deN 2 O process.
Moreover, the Co/CeO 2 -NR sample exhibits the lowest reduction temperature (peak at 318 • C) in comparison with the other samples (peak ca.335 • C), indicating the facilitation of Co 3+ species reduction over ceria nanorods.Noteworthily, the theoretical amount of hydrogen for the complete reduction of Co 3 O 4 to Co (approx.1.76 mmol H 2 g −1 , based on a 7.8 wt.% nominal loading of Co) is always surpassed by the hydrogen amount required for the reduction of Co/CeO 2 samples (Table 2).
The latter reveals the facilitation of ceria capping oxygen reduction in the presence of cobalt, further corroborating the above findings.2.4.Surface Analysis (X-ray Photoelectron Spectroscopy (XPS)) An XPS analysis was performed in order to investigate the effect of ceria morphology on the elemental chemical states and surface composition of Co/CeO 2 mixed oxides.Figure 5a shows the Ce3d XPS spectra of ceria nanoparticles of different morphology and the corresponding Co/CeO 2 samples, which can be deconvoluted into eight components [63][64][65], with the assignment of the characteristic peaks having been thoroughly described in our previous work [49].In brief, the three pairs of peaks labeled as u, v; u", v"; and u"', v"' are ascribed to Ce 4+ , whereas the residual u' and v' peaks are ascribed to Ce 3+ species.
The corresponding O 1s spectra of the samples are depicted in Figure 5b.The low binding energy peak at 529. ) and water, carbonate as well as hydroxyl species [23,56].
The proportion of Ce 3+ (%) as well as the O II /O I ratio for all samples is summarized in Table 3. Bare ceria supports exhibit a similar amount of Ce 3+ ranging from 23.3 to 25.3%.Regarding, the cobalt-ceria samples, the population of Ce 3+ species is slightly higher, varying between 26.1 and 28.5%.In particular, the Co/CeO 2 -NR sample exhibits the highest amount (28.5%) followed by Co/CeO 2 -NP (26.7%) and Co/CeO 2 -NC (26.1%), indicating the abundance of the nanorod samples in oxygen vacancies.Interestingly, the relative ratio of adsorbed to lattice oxygen (O II /O I ) and the Ce 3+ (%) follow the same order, namely, Co/CeO 2 -NR (0.60) > Co/CeO 2 -NP (0.53) > Co/CeO 2 -NC (0.51), perfectly matched to the order obtained for the catalytic performance, as it will be discussed in the sequence.It should be also noted that Co addition to CeO 2 -NR enhances both the population of reduced Ce 3+ species and the O II /O I ratio, revealing the synergistic interactions between cerium and cobalt oxides toward the formation of highly reducible composites, in agreement with the TPR results.Figure 6 depicts the Co 2p XPS spectra of Co/CeO 2 samples along with the spectrum obtained for the Co 3 O 4 reference sample for comparison purposes.The samples exhibit two major peaks of Co2p 3/2 (780 eV) and Co2p 1/2 (795 eV).According to peaks' positions and shapes, the structure of the cobalt spinel is formed [23,66,67].The Co 2+ /Co 3+ ratio of Co/CeO 2 samples derived by the deconvolution of the Co2p 1/2 and Co2p 3/2 peaks is included in Table 3.The nanorod sample, which offers the best deN 2 O performance (vide infra), exhibits the highest Co 2+ /Co 3+ ratio (1.32), followed by nanocubes (1.06) and nanopolyhedra (0.94).In view of this fact, it has been reported that samples with a high Co 2+ /Co 3+ ratio exhibit better deN 2 O performance [3,20,22,43,59], further corroborating the present findings.cobalt spinel is formed [23,66,67].The Co 2+ /Co 3+ ratio of Co/CeO2 samples derived by the deconvolution of the Co2p1/2 and Co2p3/2 peaks is included in Table 3.The nanorod sample, which offers the best deN2O performance (vide infra), exhibits the highest Co 2+ /Co 3+ ratio (1.32), followed by nanocubes (1.06) and nanopolyhedra (0.94).In view of this fact, it has been reported that samples with a high Co 2+ /Co 3+ ratio exhibit better deN2O performance [3,20,22,43,59], further corroborating the present findings.

Catalytic Evaluation Studies
The impact of ceria morphology on the catalytic decomposition of N2O under oxygen deficient and oxygen excess conditions was next examined.Figure 7a and b shows the N2O conversion profiles as a temperature function for bare ceria as well as Co/CeO2 samples in the absence and presence of

Catalytic Evaluation Studies
The impact of ceria morphology on the catalytic decomposition of N 2 O under oxygen deficient and oxygen excess conditions was next examined.Figure 7a,b shows the N 2 O conversion profiles as a temperature function for bare ceria as well as Co/CeO 2 samples in the absence and presence of oxygen, respectively.The Co/CeO 2 -NR sample exhibits the best catalytic performance, both in the absence and presence of oxygen in the gas stream.Apparently, the addition of cobalt in the ceria lattice enormously enhances the catalytic efficiency without, however, affecting the catalytic order of bare ceria samples, suggesting the pivotal role of ceria morphology on the deN 2 O performance.In terms of the half-conversion temperature (T 50 ), the following order is obtained for the mixed oxides in the absence of oxygen: Co/CeO 2 -NR (449 The same trend is observed in the presence of oxygen as well, although in slightly higher temperatures, due to its competitive sorption on the catalyst surface.In this point, it should be noted that the un-catalyzed reaction shows nearly zero N 2 O conversion in the temperature range investigated, as previously reported [29,46,68]. terms of the half-conversion temperature (T50), the following order is obtained for the mixed oxides in the absence of oxygen: Co/CeO2-NR (449 °C) > Co/CeO2-NP (458 °C) > Co/CeO2-NC (464 °C).The same trend is observed in the presence of oxygen as well, although in slightly higher temperatures, due to its competitive sorption on the catalyst surface.In this point, it should be noted that the uncatalyzed reaction shows nearly zero N2O conversion in the temperature range investigated, as previously reported [29,46,68].The above findings can be well-interpreted by taking into account a redox-type mechanism for the decomposition of N2O over cobalt spinel oxides [4,23,24,30,59,[69][70][71][72][73]: The above findings can be well-interpreted by taking into account a redox-type mechanism for the decomposition of N 2 O over cobalt spinel oxides [4,23,24,30,59,[69][70][71][72][73]: In this mechanistic sequence, N 2 O is initially chemisorbed on the Co 2+ sites (Equation ( 1)) which are considered as the active centres for initiating the N 2 O dissociative adsorption.Then, the regeneration of the active sites is taking place through the Co 3+ /Co 2+ redox cycle, involving the combination of O − into O 2 − (Equation ( 2)) and the desorption of molecular oxygen (Equation ( 3)), which finally leads to the regeneration of those sites [69].However, in the case of Co 3 O 4 /CeO 2 mixed oxides, the excellent redox characteristics of ceria, such as oxygen storage capacity and oxygen mobility, can be further accounted for the regeneration of active sites through the following steps [69]: Based on the above mechanistic scheme, the superiority of the Co/CeO 2 sample with a rod-like morphology can receive a consistent explanation.More specifically, nanorod-shaped ceria with (110) and (100) reactive planes exhibit enhanced oxygen kinetics and reducibility as it has the highest population of loosely bound oxygen species (Table 2), which is a decisive factor in terms of deN 2 O activity.In other words, the high amount of weakly bound oxygen species present in the Co 3 O 4 /CeO 2 samples of rod-like morphology, linked directly to oxygen vacancy formation and oxygen mobility, could be considered responsible for the formation and the consequent regeneration of active sites.In this regard, a perfect interrelation between the catalytic performance (in terms of the half-conversion temperature, T 50 ) and the redox properties (in terms of the ratio of surface oxygen to bulk oxygen, O s /O b ) is disclosed, as illustrated in Figure 8.This clearly justifies the key role of redox properties on the deN 2 O process.In a similar manner, Liu et al. [28] have pointed out that the synergistic interaction between the two oxide phases in a CuO-CeO 2 mixed oxide enhances the reducibility and consequently the deN 2 O efficiency as the surface-adsorbed oxygen species is easily desorbed and the active sites' regeneration is enabled.Moreover, ceria nanorods facilitate the reduction of Co 3+ to Co 2+ active sites (Table 3), further contributing to the superior catalytic performance of the Co/CeO2-NR sample.Along the same line, it has been recently reported that ceria nanorods stabilize the partial oxidation state of Co in CoOX/CeO2 catalysts via the facilitation of oxygen transfer at the metal-support interface [74].It More interestingly, the deN 2 O performance of CeO 2 as well as the Co 3 O 4 /CeO 2 samples totally coincides, indicating the significance of the ceria carrier.However, the superiority of the mixed oxides in comparison to the bare ceria samples is evident, reflecting the synergistic interactions between cobalt and cerium oxides.The latter is manifested by the improved redox properties (in terms of H 2 consumption and TPR onset temperature) of Co 3 O 4 /CeO 2 mixed oxides as compared to bare ceria (Table 2).In a similar manner, the incorporation of cobalt into the ceria lattice increases both the amount of the adsorbed oxygen species (O − /O 2 2− ) and Ce 3+ (Table 3), related with the surface oxygen reduction and the abundance in oxygen vacancies (O vac ).Moreover, ceria nanorods facilitate the reduction of Co 3+ to Co 2+ active sites (Table 3), further contributing to the superior catalytic performance of the Co/CeO 2 -NR sample.Along the same line, it has been recently reported that ceria nanorods stabilize the partial oxidation state of Co in CoO X /CeO 2 catalysts via the facilitation of oxygen transfer at the metal-support interface [74].It should be, therefore, deduced that ceria nanorods with the exposed (110) and (100) facets show the highest surface-to-bulk oxygen ratio resulting in improved reducibility and oxygen kinetics while exhibiting the highest amount of weakly bound oxygen species which is a decisive factor in the deN 2 O process.Upon cobalt addition, the nanorod sample exhibits in addition the highest population in Ce 3+ /Co 2+ redox pairs, indicative of abundant oxygen vacancies, which, along with its enhanced reducibility, leads to a superior deN 2 O performance.
In this point, the enhanced textural characteristics (BET area and pore volume) of Co/CeO 2 -NR as compared to Co/CeO 2 -NC should be also mentioned, which could be further accounted for its enhanced deN 2 O performance.Thus, by taking into account the specific activity normalized per unit of surface area (nmol m −2 s −1 ) instead of mass unit (nmol g −1 s −1 ), an inferior performance is observed for Co/CeO 2 -NR compared to Co/CeO 2 -NC (Table 4).On the other hand, Co 3 O 4 /CeO 2 -NR exhibits a superior deN 2 O performance (both in terms of conversion and specific activity) as compared to Co 3 O 4 /CeO 2 -NP despite their similar structural (crystallite size) and textural (surface area) properties (Table 1).The latter clearly reveals the importance of exposed facets and redox properties on the deN 2 O process, as it has been similarly reported by Zabilskiy et al. [45] for CuO/CeO 2 nanostructures of different morphology.Therefore, on the basis of the present findings, it can be deduced that the enhanced N 2 O conversion performance of Co 3 O 4 /CeO 2 -NR mixed oxides could be attributed to a compromise between redox and textural characteristics.

Materials Synthesis
In the present work, the chemicals that were used were of analytical reagent grade.Ce(NO 3 ) 3 •6H 2 O (Fluka, Bucharest, Romania, purity ≥99.0%) and Co(NO 3 ) 2 •6H 2 O (Sigma-Aldrich, Taufkirchen, Germany, purity ≥98%) were employed as precursor compounds for the preparation of bare ceria as well as Co/CeO 2 mixed oxides.Also, NaOH (Sigma-Aldrich, Taufkirchen, Germany, purity ≥98%) and ethanol (ACROS Organics, Geel, Belgium, purity 99.8%,) were used during materials synthesis.Initially, the hydrothermal method was applied for the preparation of bare ceria nanoparticles, as described in detail in our previous work [49].In brief, ceria nanorods (CeO 2 -NR) were synthesized by dissolving NaOH (36.7 M) in double deionized water and then adding an appropriate amount of an aqueous solution of Ce(NO 3 ) 3 •6H 2 O (0.13 M) under vigorous stirring.Next, the transfer of the final slurry into a Teflon bottle and its aging at 90 • C for 24 h occurred.For the synthesis of ceria nanopolyhedra (CeO 2 -NP), a similar procedure was followed, employing, however, a lower amount of NaOH (6 M).In order to synthesize ceria nanocubes (CeO 2 -NC), the same procedure as the one described above for the synthesis of ceria nanorods was followed, with the obtained slurry to be aged at 180 • C instead of 90 • C. In all cases, centrifugation was used for the recovery of the solid products that were thoroughly washed with double deionized water until a neutral pH was reached and finally washed with ethanol so as to avoid the nanoparticles' agglomeration.Afterwards, drying of the precipitate at 90 • C for 12 h followed by calcination at 500 • C for 2 h under air flow (heating ramp 5 • C/min) was carried out.
The Co/CeO 2 -NX catalysts where NX stands for NP: nanopolyhedra, NR: nanorods and NC: nanocubes were prepared by wet impregnation, employing an aqueous solution of Co(NO 3 ) 2 •6H 2 O, in order to achieve an atomic ratio Co/(Co+Ce) of 0.2 which corresponds to 7.8 wt.% of Co loading.Heating under stirring of the obtained suspensions until complete water evaporation occurred, followed by drying at 90 • C for 12 h and final calcination at 500 • C for 2 h under air flow (heating ramp 5 • C/min).

Materials Characterization
The porosity of the materials was evaluated by the N 2 -adsorption isotherms at −196 • C, using an ASAP 2010 (Micromeritics, Norcross, GA, USA) apparatus (from ReQuimTe Analyses Laboratory, Universidade Nova de Lisboa, Lisboa, Portugal).The samples were previously degassed at 300 • C for 6 h.The specific surface area was calculated by the Brunauer-Emmett-Teller (BET) equation [75].
Structural characterization was carried out by means of X-ray diffraction (XRD) in a PAN'alytical X'Pert MPD equipped with a X'Celerator detector and secondary monochromator (Cu Kα λ = 0.154 nm, 50 kV, 40 mA; data recorded at a 0.017º step size, 100 s/step) in the University of Trás-os-Montes e Alto Douro.The collected spectra were analyzed by Rietveld refinement using PowderCell software, allowing the determination of crystallite sizes by means of the Williamson-Hall plot.
The redox properties were assessed by Temperature Programmed Reduction (TPR) experiments in an AMI-200 Catalyst Characterization Instrument (Altamira Instruments, Pittsburgh, PA, USA), employing H 2 as a reducing agent.In a typical H 2 -TPR experiment, 50 mg of the sample (grain size 180-355 µm) was heated up to 1100 • C (10 • C/min) under H 2 flow (1.5 cm 3 ) balanced with He (29 cm 3 ).The amount of H 2 consumed (mmol g −1 ) was calculated by taking into account the integrated area of TPR peaks, calibrated against a known amount of CuO standard sample [76,77].
The surface composition and the chemical state of each element were determined by X-ray photoelectron spectroscopy (XPS) analyses, performed on a VG Scientific ESCALAB 200A spectrometer using Al Kα radiation (1486.6 eV) in CEMUP.The charge effect was corrected using the C1s' peak as a reference (binding energy of 285 eV).The CASAXPS software was used for data analysis.
The samples were imaged by transmission electron microscopy (TEM).The analyses were performed on a Leo 906E apparatus (Austin, TX, USA), at 120 kV in the University of Trás-os-Montes e Alto Douro.The samples were prepared by ultrasonic dispersion, and a 400 mesh formvar/carbon copper grid (Agar Scientific, Essex, UK) was dipped into the solution for the TEM analysis.

Catalytic Performance Evaluation
The catalytic studies for the N 2 O decomposition took place in a quartz fixed-bed U-shaped reactor (0.8 cm i.d.) with 100 mg of catalyst loading (grain size 180-355 µm).The feed gas (1000 ppm N 2 O and 0 or 2 vol.% O 2 ) total flow rate was 150 cm 3 /min which corresponds to a Gas Hour Space Velocity (GHSV) of 40,000 h −1 .The analysis of the gases was performed by a gas chromatograph (SHIMADZU 14B).The apparatus is equipped with a TCD detector and two separation columns (Molecular Sieve 5A for O 2 , N 2 measurements and Porapack QS for N 2 O measurement).Prior to the catalytic activity measurements, the materials under consideration were subjected to further processing under He flow (100 cm 3 /min) at 400 • C. In order to minimize the external and internal diffusion limitations, preliminary experiments concerning the influence of particle size and W/F ratio on deN 2 O catalytic performance were carried out.Based on these experiments, a catalyst particle size in the range of 180-355 µm was selected, in addition to a W/F ratio of 0.04 g s cm −3 .The conversion of N 2 O (X N2O ) was calculated from the difference in N 2 O concentration between the inlet and outlet gas streams, according to the equation The specific reaction rate (r, mol m −2 s −1 ) of the N 2 O decomposition was also estimated using the following formula: where F and V m are the total flow rate and gas molar volume, respectively, at standard ambient temperature and pressure conditions (298 K and 1 bar), m cat is the catalyst's mass and S BET is the surface area.

Conclusions
In this work, three different ceria nanoshaped materials (nanorods, nanocubes and nanopolyhedra) were hydrothermally synthesized and used as supports for the cobalt oxide phase.Both single CeO 2 and Co/CeO 2 mixed oxides were catalytically assessed during the decomposition of N 2 O in the presence and absence of oxygen.For bare ceria samples, the following deN 2 O order was obtained: CeO 2 -NR (nanorods) > CeO 2 -NP (nanopolyhedra) > CeO 2 -NC (nanocubes).Most importantly, cobalt addition to the CeO 2 carriers greatly enhances the N 2 O decomposition, not affecting at all the order obtained for the bare ceria supports and clearly reflecting the key role of support.The present results clearly reveal the key role of support morphology on the textural, structural and redox properties, reflected then on the catalytic performance of Co 3 O 4 /CeO 2 mixed oxides.Among the different samples investigated, the cobalt-ceria nanorods (Co/CeO 2 -NR) exposing {100} and {110} facets showed the best deN 2 O performance, ascribed mainly to their abundance in Co 2+ active sites in conjunction to their enhanced redox and textural properties.

Figure 2 .
Figure 2. The XRD patterns of the CeO2 and Co/CeO2 samples.

Figure 2 .
Figure 2. The XRD patterns of the CeO 2 and Co/CeO 2 samples.
3 eV is attributed to the lattice oxygen (O I ) of Co 3 O 4 and CeO 2 phases, and the high binding energy peak at 531.3 eV corresponds to the chemisorbed oxygen (O II ) such as adsorbed oxygen (O − /O 2 2−

Figure 5 .
Figure 5.The X-ray photoelectron spectroscopy (XPS) spectra of (a) Ce 3d and (b) O 1s of bare CeO 2 and Co/CeO 2 samples.

Figure 6 .
Figure 6.The Co 2p XPS spectra of the Co3O4 and Co/CeO2 samples: The Co 2p XPS spectra of Co/CeO2 samples have been magnified.

Figure 6 .
Figure 6.The Co 2p XPS spectra of the Co 3 O 4 and Co/CeO 2 samples: The Co 2p XPS spectra of Co/CeO 2 samples have been magnified.

Figure 7 .
Figure 7. N2O conversion as a function of temperature for CeO2 and Co/CeO2 samples of different morphology (a) in the absence and (b) in the presence of oxygen: The reaction conditions are 1000 ppm N2O, 0 or 2% O2 and Gas Hour Space Velocity (GHSV) = 40,000 h −1 .

Figure 7 .
Figure 7. N 2 O conversion as a function of temperature for CeO 2 and Co/CeO 2 samples of different morphology (a) in the absence and (b) in the presence of oxygen: The reaction conditions are 1000 ppm N 2 O, 0 or 2% O 2 and Gas Hour Space Velocity (GHSV) = 40,000 h −1 .

Figure 8 .
Figure 8.The half-conversion temperature (T 50 ) as a function of the TPR surface-to-bulk oxygen ratio (O s /O b ).

Table 1 .
The textural and structural properties of bare CeO 2 and Co/CeO 2 samples.

Table 2 .
The redox properties of the bare CeO 2 and Co/CeO 2 samples.
a Estimated by the area of the corresponding temperature programmed reduction (TPR) peaks, which is calibrated against a known amount of CuO standard sample.

Table 3 .
The XPS results of bare CeO 2 and Co/CeO 2 samples.

Table 4 .
The N 2 O conversion and specific activity of Co/CeO 2 samples at 420 • C: The reaction conditions are 1000 ppm N 2 O, 0 or 2 vol.% O 2 and GHSV = 40,000 h −1 .