catalysts Tandem Reactions Based on the Cyclization of Carbon Dioxide and Propargylic Alcohols: Derivative Applications of α -Alkylidene Carbonates

: As a well-known greenhouse gas, carbon dioxide (CO 2 ) has attracted increasing levels of attention in areas of energy, environment, climate, etc. Notably, CO 2 is an abundant, nonﬂammable, and renewable C1 feedstock in view of chemistry. Therefore, the transformation of CO 2 into organic compounds is an extremely attractive research topic in modern green and sustainable chemistry. Among the numerous CO 2 utilization methods, carboxylative cycloaddition of CO 2 into propargylic alcohols is an ideal route due to the corresponding products, α -alkylidene cyclic carbonates, which are a series of highly functionalized compounds that supply numerous potential methods for the construction of various synthetically and biologically valuable agents. This cyclization reaction has been intensively studied and systematically summarized, in the past years. Therefore, attention has been gradually transferred to produce more derivative compounds. Herein, the tandem reactions of this cyclization with hydration, amination, alcoholysis, and isomerization to synthesize α -hydroxyl ketones, oxazolidinones, carbamates, unsymmetrical carbonates, tetronic acids, ethylene etc. were systematically reviewed.


Introduction
Since the industrial revolution, fossil fuels have become the primary energy source for human beings. Simultaneously, continuous consumption of fossil fuels has produced excessive carbon dioxide (CO 2 ), which leads to global warming and causes severe environmental impact such as rising sea levels, frequent extreme weather events, and imbalances of the ecosystem [1][2][3][4]. The threat of global warming to the environment and climate has been a significant challenge for human beings in the 21st century. Accordingly, the capture and treatment of CO 2 has become a strategic priority and has been intensively investigated [5]. In this aspect, the carbon capture and utilization (CCU) strategy has been regarded as a promising option for controlling the accumulation of CO 2 [6][7][8][9][10][11][12][13]. Compared with the traditional carbon capture and storage (CCS) strategy, CCU eliminates the extra energy-consuming process of CO 2 desorption and compression whereby CO 2 can be

Three-Component Reactions of Propargylic Alcohols, CO2 and Amines
As a series of typical nucleophilic reagents, amines can be employed in the threecomponent tandem reactions with CO2 and propargylic alcohols to effectively prepare oxazolidinones or carbamates, both of which are vital skeletons in biology, pharmaceutical chemistry and organic synthesis [60][61][62][63][64]. These three-component reactions undertake a two-step procedure. In the first step, the cyclic carbonate intermediates M1 are formed by the carboxylative cyclization of CO2 with the propargylic alcohols. The next step is the nucleophilic attack of the nitrogen atoms in amines to the carbonyl groups in M1. After this ring-opening process, the intramolecular cyclization or the keto-enol tautomerism occurs and the desired oxazolidinones 1, oxazolones 2 or carbamates 3 are generated. Generally, the three-component reaction of tertiary propargylic alcohols, CO2 and primary amines affords the 4-methyleneoxazolidin-2-ones (1); the three-component reaction of primary or secondary propargylic alcohols, CO2 and primary amines affords 4-methyloxazol-2-ones (2); and the three-component reaction of propargylic alcohols, CO2 and secondary amines affords β-oxopropylcarbamates (3), as illustrated in Scheme 1.

Three-Component Reactions of Propargylic Alcohols, CO 2 and Amines
As a series of typical nucleophilic reagents, amines can be employed in the threecomponent tandem reactions with CO 2 and propargylic alcohols to effectively prepare oxazolidinones or carbamates, both of which are vital skeletons in biology, pharmaceutical chemistry and organic synthesis [60][61][62][63][64]. These three-component reactions undertake a two-step procedure. In the first step, the cyclic carbonate intermediates M1 are formed by the carboxylative cyclization of CO 2 with the propargylic alcohols. The next step is the nucleophilic attack of the nitrogen atoms in amines to the carbonyl groups in M1. After this ring-opening process, the intramolecular cyclization or the keto-enol tautomerism occurs and the desired oxazolidinones 1, oxazolones 2 or carbamates 3 are generated. Generally, the three-component reaction of tertiary propargylic alcohols, CO 2 and primary amines affords the 4-methyleneoxazolidin-2-ones (1); the three-component reaction of primary or secondary propargylic alcohols, CO 2 and primary amines affords 4-methyloxazol-2-ones (2); and the three-component reaction of propargylic alcohols, CO 2 and secondary amines affords β-oxopropylcarbamates (3), as illustrated in Scheme 1.
Until 2005, a relatively economical copper(I) catalyst was developed for this threecomponent reaction by Deng et al. [66], who reported a type of recyclable CuCl/1-butyl-3-methylimidazolium tetrafluoroborate ([BMIm]BF4) system. With this catalyst, 4-methylene-2-oxazolidinones could be obtained in 78-95% yields from the corresponding propargylic alcohols and primary amines under 2.5 MPa of CO2 (Scheme 3). Furthermore, the CuCl/[BMIm]BF4 system could be reused at least 3 times without obvious activity decline. Unfortunately, when primary and secondary propargylic alcohols or aniline were applied as one of the substrates, the desired oxazolidinone products could not be formed. In 2007, Jiang et al. [67] proposed a superior copper-catalyzed process in which CuI was utilized under supercritical CO2 (scCO2) conditions. Both 4-methyleneoxazolidin-2-ones and 4methyloxazol-2-ones were obtained from the reactions of various primary propargylic alcohols and secondary propargylic alcohols with primary amines in 70-95% and 88-96% yields (Scheme 4), indicating its broad substrate scope. Shortly afterwards, Zhao et al. [68] found that CuCl was also an effective catalyst without the participation of ILs, which enabled this three-component reaction under solvent-free and atmospheric CO2 pressure. Although excess primary amines were required and the yields were relatively low, the oxazolidinones could be obtained through this facile and mild process (Scheme 5).
In 2019, Wang et al. [69] reported a CuI/tetrabutylphosphoniumimidazol ([P4444][Im]) system for the transformation of CO2 into oxazolidinones under room temperature and atmospheric CO2 pressure (Scheme 6). The corresponding products were obtained in 54-87% yields. However, anilines also failed to generate the oxazolidinones. Regarding the mechanism, CuI and [P4444][Im] synergistically catalyzed the reaction. CuI activated the C≡C bonds of the propargyl alcohols; meanwhile, [P4444][Im] activated the hydroxyl groups of the propargyl alcohols. Furthermore, the authors proposed that the catalytic activity was affected by the alkalinity of ILs. A higher pKa would enhance its CO2 fixation ability in this three-component reaction, which led to an improved reaction performance of CO2, propargylic alcohols and primary amines. On the other hand, the dissociation ability of the metal anions played a pivotal role in the activity of the halogenated copper salts. Generally, a stronger dissociation ability of the anions would result in the better catalytic activity of the corresponding copper salt.
Until 2005, a relatively economical copper(I) catalyst was developed for this threecomponent reaction by Deng et al. [66], who reported a type of recyclable CuCl/1-butyl-3methylimidazolium tetrafluoroborate ([BMIm]BF 4 ) system. With this catalyst, 4-methylene-2-oxazolidinones could be obtained in 78-95% yields from the corresponding propargylic alcohols and primary amines under 2.5 MPa of CO 2 (Scheme 3). Furthermore, the CuCl/[BMIm]BF 4 system could be reused at least 3 times without obvious activity decline. Unfortunately, when primary and secondary propargylic alcohols or aniline were applied as one of the substrates, the desired oxazolidinone products could not be formed. In 2007, Jiang et al. [67] proposed a superior copper-catalyzed process in which CuI was utilized under supercritical CO 2 (scCO 2 ) conditions. Both 4-methyleneoxazolidin-2-ones and 4-methyloxazol-2-ones were obtained from the reactions of various primary propargylic alcohols and secondary propargylic alcohols with primary amines in 70-95% and 88-96% yields (Scheme 4), indicating its broad substrate scope. Shortly afterwards, Zhao et al. [68] found that CuCl was also an effective catalyst without the participation of ILs, which enabled this three-component reaction under solvent-free and atmospheric CO 2 pressure. Although excess primary amines were required and the yields were relatively low, the oxazolidinones could be obtained through this facile and mild process (Scheme 5).
In 2019, Wang et al. [69] reported a CuI/tetrabutylphosphoniumimidazol ([P 4444 ][Im]) system for the transformation of CO 2 into oxazolidinones under room temperature and atmospheric CO 2 pressure (Scheme 6). The corresponding products were obtained in 54-87% yields. However, anilines also failed to generate the oxazolidinones. Regarding the mechanism, CuI and [P 4444 ][Im] synergistically catalyzed the reaction. CuI activated Apart from the copper(I) compounds, silver salts had been found to be an excellent catalyst for this three-component reaction. In 2009, Jiang and Zhao [70] reported that AgOAc could efficiently promote the reaction of internal propargylic alcohols with primary amines in scCO2. It was noteworthy that when internal propargylic alcohols were used as substrates, both the primary and secondary alcohols could participate in this reaction, providing corresponding oxazolidinones rather than oxazolones (Scheme 7). In 2014, He group [71] developed a AgWO4/Ph3P system that worked under solvent-free conditions and 0.5 MPa of CO2. The oxazolidinones derivatives were obtained in 83%-95% yields (Scheme 8). Notably, this catalytic system was not sensitive to air and moisture, which facilitated the operations of the CO2 conversion process. Recently, Zhang and He et al. [72] demonstrated that the 1,3-oxazolidin-2-one derivatives could be achieved from the three-component reaction of typical terminal propargylic alcohols, CO2, and diverse primary amines employing Ag2CO3 as catalyst and (p-MeOC6H4)3P as an additive. Specifically, they developed a one-pot stepwise strategy to afford oxazolidinones. In this stepwise process, propargylic alcohols react with CO2 to form α-alkylidene cyclic carbonates under 2 MPa of CO2. Then, primary amines were directly added without any separation operation. Finally, the oxazolidinones were obtained at 120 °C under atmospheric CO2 pressure (Scheme 9). Moreover, this catalytic system could be reused at least 3 times.   Apart from the copper(I) compounds, silver salts had been found to be an excellent catalyst for this three-component reaction. In 2009, Jiang and Zhao [70] reported that AgOAc could efficiently promote the reaction of internal propargylic alcohols with primary amines in scCO2. It was noteworthy that when internal propargylic alcohols were used as substrates, both the primary and secondary alcohols could participate in this reaction, providing corresponding oxazolidinones rather than oxazolones (Scheme 7). In 2014, He group [71] developed a AgWO4/Ph3P system that worked under solvent-free conditions and 0.5 MPa of CO2. The oxazolidinones derivatives were obtained in 83%-95% yields (Scheme 8). Notably, this catalytic system was not sensitive to air and moisture, which facilitated the operations of the CO2 conversion process. Recently, Zhang and He et al. [72] demonstrated that the 1,3-oxazolidin-2-one derivatives could be achieved from the three-component reaction of typical terminal propargylic alcohols, CO2, and diverse primary amines employing Ag2CO3 as catalyst and (p-MeOC6H4)3P as an additive. Specifically, they developed a one-pot stepwise strategy to afford oxazolidinones. In this stepwise process, propargylic alcohols react with CO2 to form α-alkylidene cyclic carbonates under 2 MPa of CO2. Then, primary amines were directly added without any separation operation. Finally, the oxazolidinones were obtained at 120 °C under atmospheric CO2 pressure (Scheme 9). Moreover, this catalytic system could be reused at least 3 times.
Apart from the copper(I) compounds, silver salts had been found to be an excellent catalyst for this three-component reaction. In 2009, Jiang and Zhao [70] reported that AgOAc could efficiently promote the reaction of internal propargylic alcohols with primary amines in scCO2. It was noteworthy that when internal propargylic alcohols were used as substrates, both the primary and secondary alcohols could participate in this reaction, providing corresponding oxazolidinones rather than oxazolones (Scheme 7). In 2014, He group [71] developed a AgWO4/Ph3P system that worked under solvent-free conditions and 0.5 MPa of CO2. The oxazolidinones derivatives were obtained in 83%-95% yields (Scheme 8). Notably, this catalytic system was not sensitive to air and moisture, which facilitated the operations of the CO2 conversion process. Recently, Zhang and He et al. [72] demonstrated that the 1,3-oxazolidin-2-one derivatives could be achieved from the three-component reaction of typical terminal propargylic alcohols, CO2, and diverse primary amines employing Ag2CO3 as catalyst and (p-MeOC6H4)3P as an additive. Specifically, they developed a one-pot stepwise strategy to afford oxazolidinones. In this stepwise process, propargylic alcohols react with CO2 to form α-alkylidene cyclic carbonates under 2 MPa of CO2. Then, primary amines were directly added without any separation operation. Finally, the oxazolidinones were obtained at 120 °C under atmospheric CO2 pressure (Scheme 9). Moreover, this catalytic system could be reused at least 3 times.   Although transition metal compounds proved to be suitable catalysts for promoting CO 2 conversion, most reported systems were costly, unstable, and sensitive to air, water, or light. Therefore, some attention has been drawn to metal-free organocatalysis due to its economy, tunability, and functionality [73,74].
In 1990, Fournier and his colleagues [75] demonstrated that organocatalysts could efficiently promote the three-component tandem reaction of CO 2 , propargylic alcohols, and primary amines. In the presence of tri-n-butylphosphine (Bu 3 P), 4-methylene oxazolidin-2-ones were generated from the reaction of 2-methyl-3-butyn-2-ol, CO 2 , and primary amines in 38-72% yields under 5 MPa of CO 2 (Scheme 10). Based on this, the Costa group [76] discovered that a series of organic bases and bicyclic guanidines, were a type of favorable catalysts for the reaction of scCO 2 with terminal propargylic alcohols and primary amines. The yield of desired products were generally high when primary alkyl-, allyl-and benzylamines were employed, while lower yields were given using primary arylamines (Scheme 11). In 2016, Liu and Hua [77] revealed that both secondary and tertiary propargylic alcohols could efficiently react with primary amines and CO 2 under the catalysis of 2,2',2"-terpyridine in one-pot at 3 MPa of CO 2 to afford oxazolidinones and oxazolones (Scheme 12). Although transition metal compounds proved to be suitable catalysts for promoting CO2 conversion, most reported systems were costly, unstable, and sensitive to air, water, or light. Therefore, some attention has been drawn to metal-free organocatalysis due to its economy, tunability, and functionality [73,74].
In 1990, Fournier and his colleagues [75] demonstrated that organocatalysts could efficiently promote the three-component tandem reaction of CO2, propargylic alcohols, and primary amines. In the presence of tri-n-butylphosphine (Bu3P), 4-methylene oxazolidin-2-ones were generated from the reaction of 2-methyl-3-butyn-2-ol, CO2, and primary amines in 38-72% yields under 5 MPa of CO2 (Scheme 10). Based on this, the Costa group [76] discovered that a series of organic bases and bicyclic guanidines, were a type of favorable catalysts for the reaction of scCO2 with terminal propargylic alcohols and primary amines. The yield of desired products were generally high when primary alkyl-, allyl-and benzylamines were employed, while lower yields were given using primary arylamines (Scheme 11). In 2016, Liu and Hua [77] revealed that both secondary and tertiary propargylic alcohols could efficiently react with primary amines and CO2 under the catalysis of 2,2′,2"-terpyridine in one-pot at 3 MPa of CO2 to afford oxazolidinones and oxazolones (Scheme 12). ILs are a type of new green organic solvents, which have been applied in numerous areas owing to their unique features such as high stability, nonvolatility, recyclability, and tunability [78,79]. Mainly, ILs are often used as catalysts for the conversion of CO2. In 2005, Scheme 10. Bu 3 P catalyzed three-component reaction of CO 2 , propargylic alcohols and primary amines. Although transition metal compounds proved to be suitable catalysts for promoting CO2 conversion, most reported systems were costly, unstable, and sensitive to air, water, or light. Therefore, some attention has been drawn to metal-free organocatalysis due to its economy, tunability, and functionality [73,74].
In 1990, Fournier and his colleagues [75] demonstrated that organocatalysts could efficiently promote the three-component tandem reaction of CO2, propargylic alcohols, and primary amines. In the presence of tri-n-butylphosphine (Bu3P), 4-methylene oxazolidin-2-ones were generated from the reaction of 2-methyl-3-butyn-2-ol, CO2, and primary amines in 38-72% yields under 5 MPa of CO2 (Scheme 10). Based on this, the Costa group [76] discovered that a series of organic bases and bicyclic guanidines, were a type of favorable catalysts for the reaction of scCO2 with terminal propargylic alcohols and primary amines. The yield of desired products were generally high when primary alkyl-, allyl-and benzylamines were employed, while lower yields were given using primary arylamines (Scheme 11). In 2016, Liu and Hua [77] revealed that both secondary and tertiary propargylic alcohols could efficiently react with primary amines and CO2 under the catalysis of 2,2′,2"-terpyridine in one-pot at 3 MPa of CO2 to afford oxazolidinones and oxazolones (Scheme 12). ILs are a type of new green organic solvents, which have been applied in numerous areas owing to their unique features such as high stability, nonvolatility, recyclability, and tunability [78,79]. Mainly, ILs are often used as catalysts for the conversion of CO2. In 2005, Scheme 11. MTBD or TBD catalyzed three-component reaction of CO 2 , propargylic alcohols and primary amines. Although transition metal compounds proved to be suitable catalysts for promoting CO2 conversion, most reported systems were costly, unstable, and sensitive to air, water, or light. Therefore, some attention has been drawn to metal-free organocatalysis due to its economy, tunability, and functionality [73,74].
In 1990, Fournier and his colleagues [75] demonstrated that organocatalysts could efficiently promote the three-component tandem reaction of CO2, propargylic alcohols, and primary amines. In the presence of tri-n-butylphosphine (Bu3P), 4-methylene oxazolidin-2-ones were generated from the reaction of 2-methyl-3-butyn-2-ol, CO2, and primary amines in 38-72% yields under 5 MPa of CO2 (Scheme 10). Based on this, the Costa group [76] discovered that a series of organic bases and bicyclic guanidines, were a type of favorable catalysts for the reaction of scCO2 with terminal propargylic alcohols and primary amines. The yield of desired products were generally high when primary alkyl-, allyl-and benzylamines were employed, while lower yields were given using primary arylamines (Scheme 11). In 2016, Liu and Hua [77] revealed that both secondary and tertiary propargylic alcohols could efficiently react with primary amines and CO2 under the catalysis of 2,2′,2"-terpyridine in one-pot at 3 MPa of CO2 to afford oxazolidinones and oxazolones (Scheme 12). ILs are a type of new green organic solvents, which have been applied in numerous areas owing to their unique features such as high stability, nonvolatility, recyclability, and tunability [78,79]. Mainly, ILs are often used as catalysts for the conversion of CO2. In 2005, Scheme 12. 2,2',2"-terpyridine catalyzed three-component reaction of CO 2 , propargylic alcohols and primary amines.
ILs are a type of new green organic solvents, which have been applied in numerous areas owing to their unique features such as high stability, nonvolatility, recyclability, and tunability [78,79]. Mainly, ILs are often used as catalysts for the conversion of CO 2 . ScCO2 has been recognized as an environmentally friendly alternative to organic solvents owing to its nonflammability, easy separation, availability and low cost. In particular, it could be used as a green reaction medium as well as an exceptional raw material [67]. In order to develop an efficient and eco-friendly process for transforming CO2 into oxazolidinones, Xu et al. [81] tried to adopt scCO2 to react with propargylic alcohols and primary amines in the absence of any additional catalyst and solvent under 14 MPa pressure. Although aniline and tert-butylamine could not produce the desired product, the corresponding 4-methyleneoxazolidin-2-ones were smoothly given in 65-88% yields (Scheme 14).
Apart from the intensively studied homogeneous catalysis, various kinds of heterogeneous catalysts, including metal-oxides [82], metal nanoparticles [83], molecular sieves [84], silica-supported metal salts [85], and porous polymers [86], etc., were also employed to transform CO2 into high-value chemicals. Recently, metal-organic frameworks (MOFs) have been demonstrated to be favorable solid-state catalysts, owing to their high porosity, thermal stability, structural diversity, and excellent reusability [87,88]. Additionally, MOFs have been regarded as one of the most effective and promising CO2 adsorbents. Therefore, MOFs can significantly heighten the local concentration of CO2 near the catalytic sites to promote the conversion of CO2 [89]. In this aspect, Fei et al. [87] synthesized a Ag(I)-embedded sulfonate-MOF, a non-interpenetrated sulfonate-based porous structure with a prototypical primitive-cubic (pcu) topology, which possessed high CO2 affinity and alkyne activation properties. This MOF could efficiently promote the cyclization reaction of propargylic alcohols with CO2 and the three-component reaction of propargylic alcohols, CO2 and primary amines affording α-alkylidene cyclic carbonates and oxazolidinones with excellent yields under atmospheric pressure (Scheme 15). ScCO 2 has been recognized as an environmentally friendly alternative to organic solvents owing to its nonflammability, easy separation, availability and low cost. In particular, it could be used as a green reaction medium as well as an exceptional raw material [67]. In order to develop an efficient and eco-friendly process for transforming CO 2 into oxazolidinones, Xu et al. [81] tried to adopt scCO 2 to react with propargylic alcohols and primary amines in the absence of any additional catalyst and solvent under 14 MPa pressure. Although aniline and tert-butylamine could not produce the desired product, the corresponding 4-methyleneoxazolidin-2-ones were smoothly given in 65-88% yields (Scheme 14). ScCO2 has been recognized as an environmentally friendly alternative to organic solvents owing to its nonflammability, easy separation, availability and low cost. In particular, it could be used as a green reaction medium as well as an exceptional raw material [67]. In order to develop an efficient and eco-friendly process for transforming CO2 into oxazolidinones, Xu et al. [81] tried to adopt scCO2 to react with propargylic alcohols and primary amines in the absence of any additional catalyst and solvent under 14 MPa pressure. Although aniline and tert-butylamine could not produce the desired product, the corresponding 4-methyleneoxazolidin-2-ones were smoothly given in 65-88% yields (Scheme 14).
Apart from the intensively studied homogeneous catalysis, various kinds of heterogeneous catalysts, including metal-oxides [82], metal nanoparticles [83], molecular sieves [84], silica-supported metal salts [85], and porous polymers [86], etc., were also employed to transform CO2 into high-value chemicals. Recently, metal-organic frameworks (MOFs) have been demonstrated to be favorable solid-state catalysts, owing to their high porosity, thermal stability, structural diversity, and excellent reusability [87,88]. Additionally, MOFs have been regarded as one of the most effective and promising CO2 adsorbents. Therefore, MOFs can significantly heighten the local concentration of CO2 near the catalytic sites to promote the conversion of CO2 [89]. In this aspect, Fei et al. [87] synthesized a Ag(I)-embedded sulfonate-MOF, a non-interpenetrated sulfonate-based porous structure with a prototypical primitive-cubic (pcu) topology, which possessed high CO2 affinity and alkyne activation properties. This MOF could efficiently promote the cyclization reaction of propargylic alcohols with CO2 and the three-component reaction of propargylic alcohols, CO2 and primary amines affording α-alkylidene cyclic carbonates and oxazolidinones with excellent yields under atmospheric pressure (Scheme 15).
Apart from the intensively studied homogeneous catalysis, various kinds of heterogeneous catalysts, including metal-oxides [82], metal nanoparticles [83], molecular sieves [84], silica-supported metal salts [85], and porous polymers [86], etc., were also employed to transform CO 2 into high-value chemicals. Recently, metal-organic frameworks (MOFs) have been demonstrated to be favorable solid-state catalysts, owing to their high porosity, thermal stability, structural diversity, and excellent reusability [87,88]. Additionally, MOFs have been regarded as one of the most effective and promising CO 2 adsorbents. Therefore, MOFs can significantly heighten the local concentration of CO 2 near the catalytic sites to promote the conversion of CO 2 [89]. In this aspect, Fei et al. [87] synthesized a Ag(I)-embedded sulfonate-MOF, a non-interpenetrated sulfonate-based porous structure with a prototypical primitive-cubic (pcu) topology, which possessed high CO 2 affinity and alkyne activation properties. This MOF could efficiently promote the cyclization reaction of propargylic alcohols with CO 2 and the three-component reaction of propargylic alcohols, CO 2 and primary amines affording α-alkylidene cyclic carbonates and oxazolidinones with excellent yields under atmospheric pressure (Scheme 15). ene (DBU) was employed as an additive, the yield of several oxazolidinones increased to 99%. Further, the recyclability investigation demonstrated that the activity of MOF-SO3Ag would not significantly decrease after five cycles of regeneration, and the original skeleton structure remains intact. In the mechanism study, the high catalytic activity might be ascribed to the synergistic effect between sulfonate functionality and Ag(I) ions, in which Ag(I) activated the C≡C bonds of propargylic alcohols and sulfonates which were responsible for attracting CO2 (Scheme 16).

Carbamates as Products
Originally, methods for synthesizing carbamates through a one-pot three-component reaction of CO2, propargylic alcohols, and secondary amines were reported by Bruneau and Dixneuf [91] in 1987, employing (RuCl2(Norbornadiene))n as a catalyst in CH3CN. The corresponding carbamates were given in low to moderate yields (Scheme 17). In the same year, an analogous strategy was reported by Sasaki [65], in which Ru3(CO)12 was used to afford carbamates (Scheme 18). In addition to ruthenium compounds, iron and copper complexes were found to be suitable catalysts for this reaction [92,93]. In 1997, Kim et al. [93] demonstrated that a copper complex [Cu(L)]PF6 can effectively promote this threecomponent reaction under 3.8 MPa of CO2 to afford carbamates. Years later, Jiang et al. [94] reported a AgOAc/DBU system to synthesize β-oxoalkyl carbamates from the reaction of CO2, internal propargylic alcohols and secondary amines in 1,4-dioxane under 2 MPa of CO2. Although the bulky diisopropylamines failed to give the desired products, a range of carbamates could be obtained in 70-93% yields (Scheme 19). Moreover, this Ag(I)-embedded sulfonate-MOF can be reused at least three times. In 2020, Das and Nagaraja [90] reported the one-pot three-component reaction of propargylic alcohols, CO 2 , and primary amines at room temperature and atmospheric pressure conditions in the presence of a functional MOF-SO 3 Ag, which was constructed by a Ag(I)anchored sulfonate-functionalized UiO-66 structure. When 1,8-Diazabicyclo [5.4.0]undec-7ene (DBU) was employed as an additive, the yield of several oxazolidinones increased to 99%. Further, the recyclability investigation demonstrated that the activity of MOF-SO 3 Ag would not significantly decrease after five cycles of regeneration, and the original skeleton structure remains intact. In the mechanism study, the high catalytic activity might be ascribed to the synergistic effect between sulfonate functionality and Ag(I) ions, in which Ag(I) activated the C≡C bonds of propargylic alcohols and sulfonates which were responsible for attracting CO 2 (Scheme 16). Moreover, this Ag(I)-embedded sulfonate-MOF can be reused at least three times. In 2020, Das and Nagaraja [90] reported the one-pot three-component reaction of propargylic alcohols, CO2, and primary amines at room temperature and atmospheric pressure conditions in the presence of a functional MOF-SO3Ag, which was constructed by a Ag(I)-anchored sulfonate-functionalized UiO-66 structure. When 1,8-Diazabicyclo [5.4.0]undec-7ene (DBU) was employed as an additive, the yield of several oxazolidinones increased to 99%. Further, the recyclability investigation demonstrated that the activity of MOF-SO3Ag would not significantly decrease after five cycles of regeneration, and the original skeleton structure remains intact. In the mechanism study, the high catalytic activity might be ascribed to the synergistic effect between sulfonate functionality and Ag(I) ions, in which Ag(I) activated the C≡C bonds of propargylic alcohols and sulfonates which were responsible for attracting CO2 (Scheme 16).

Carbamates as Products
Originally, methods for synthesizing carbamates through a one-pot three-component reaction of CO2, propargylic alcohols, and secondary amines were reported by Bruneau and Dixneuf [91] in 1987, employing (RuCl2(Norbornadiene))n as a catalyst in CH3CN. The corresponding carbamates were given in low to moderate yields (Scheme 17). In the same year, an analogous strategy was reported by Sasaki [65], in which Ru3(CO)12 was used to afford carbamates (Scheme 18). In addition to ruthenium compounds, iron and copper complexes were found to be suitable catalysts for this reaction [92,93]. In 1997, Kim et al. [93] demonstrated that a copper complex [Cu(L)]PF6 can effectively promote this threecomponent reaction under 3.8 MPa of CO2 to afford carbamates. Years later, Jiang et al. [94] reported a AgOAc/DBU system to synthesize β-oxoalkyl carbamates from the reaction of CO2, internal propargylic alcohols and secondary amines in 1,4-dioxane under 2 MPa of CO2. Although the bulky diisopropylamines failed to give the desired products, a range of carbamates could be obtained in 70-93% yields (Scheme 19).

Carbamates as Products
Originally, methods for synthesizing carbamates through a one-pot three-component reaction of CO 2 , propargylic alcohols, and secondary amines were reported by Bruneau and Dixneuf [91] in 1987, employing (RuCl 2 (Norbornadiene)) n as a catalyst in CH 3 CN. The corresponding carbamates were given in low to moderate yields (Scheme 17). In the same year, an analogous strategy was reported by Sasaki [65], in which Ru 3 (CO) 12 was used to afford carbamates (Scheme 18). In addition to ruthenium compounds, iron and copper complexes were found to be suitable catalysts for this reaction [92,93]. In 1997, Kim et al. [93] demonstrated that a copper complex [Cu(L)]PF 6 can effectively promote this three-component reaction under 3.8 MPa of CO 2 to afford carbamates. Years later, Jiang et al. [94] reported a AgOAc/DBU system to synthesize β-oxoalkyl carbamates from the reaction of CO 2 , internal propargylic alcohols and secondary amines in 1,4-dioxane under 2 MPa of CO 2 . Although the bulky diisopropylamines failed to give the desired products, a range of carbamates could be obtained in 70-93% yields (Scheme 19).
were up to 68-98% (Scheme 21a). According to the proposed mechanism, Ag(I) activated the C≡C bonds of propargylic alcohols; meanwhile, the Ag2CO3 and Ph3P in situ formed [(Ph3P)2Ag]2CO3 to simultaneously activate the hydroxyls of the propargyl alcohols and CO2, embedding CO2 into propargyl alcohols to generate cyclic carbonate IV via intermediates I, II and III. Afterwards, the nitrogen atoms in secondary amines attacked the carbonyl groups of the cyclic carbonate IV to produce intermediate V, followed by the tautomerization of the enol to the carbamates 3 (Scheme 21b).  were up to 68-98% (Scheme 21a). According to the proposed mechanism, Ag(I) activated the C≡C bonds of propargylic alcohols; meanwhile, the Ag2CO3 and Ph3P in situ formed [(Ph3P)2Ag]2CO3 to simultaneously activate the hydroxyls of the propargyl alcohols and CO2, embedding CO2 into propargyl alcohols to generate cyclic carbonate IV via intermediates I, II and III. Afterwards, the nitrogen atoms in secondary amines attacked the carbonyl groups of the cyclic carbonate IV to produce intermediate V, followed by the tautomerization of the enol to the carbamates 3 (Scheme 21b). were up to 68-98% (Scheme 21a). According to the proposed mechanism, Ag(I) activated the C≡C bonds of propargylic alcohols; meanwhile, the Ag2CO3 and Ph3P in situ formed [(Ph3P)2Ag]2CO3 to simultaneously activate the hydroxyls of the propargyl alcohols and CO2, embedding CO2 into propargyl alcohols to generate cyclic carbonate IV via intermediates I, II and III. Afterwards, the nitrogen atoms in secondary amines attacked the carbonyl groups of the cyclic carbonate IV to produce intermediate V, followed by the tautomerization of the enol to the carbamates 3 (Scheme 21b).   Inspired by this case, the synergistic catalytic systems of silver(I) compounds with organic additives have been widely applied in this three-component tandem reaction. In 2014, the He group developed a milder Ag 2 WO 4 /Ph 3 P system [71], which was suitable for the three-component reaction of terminal propargylic alcohols, CO 2 and secondary amines. Catalyzed by this system, carbamates were obtained in moderate to excellent yields under 0.5 MPa (Scheme 20). Subsequently, the same group found that once Ag 2 WO 4 was replaced by Ag 2 CO 3 [95], this three-component tandem reaction could be realized under atmospheric CO 2 pressure. The yields of the corresponding β-oxopropylcarbamates were up to 68-98% (Scheme 21a). According to the proposed mechanism, Ag(I) activated the C≡C bonds of propargylic alcohols; meanwhile, the Ag 2 CO 3 and Ph 3 P in situ formed [(Ph 3 P) 2 Ag] 2 CO 3 to simultaneously activate the hydroxyls of the propargyl alcohols and CO 2 , embedding CO 2 into propargyl alcohols to generate cyclic carbonate IV via intermediates I, II and III. Afterwards, the nitrogen atoms in secondary amines attacked the carbonyl groups of the cyclic carbonate IV to produce intermediate V, followed by the tautomerization of the enol to the carbamates 3 (Scheme 21b).
Driven by these works, ever increasing attention has been paid to developing the reaction conditions' mildness and economy for the reaction system, especially for the low CO 2 pressure and recycling performance of the catalyst. In 2018, Zhang and He et al. [72] reported the Ag 2 CO 3 /(p-MeOC 6 H 4 ) 3 system for the synthesis of β-oxopropylcarbamates via a one-pot stepwise method. Similar to the abovementioned synthesis method for oxazolidinones, the first step was to generate α-alkylidene cyclic carbonates under 2 MPa of CO 2 . Then, the second step involved directly adding secondary amines to synthesize carbamates under ambient temperature and atmospheric CO 2 pressure without any separation operations or additional additives (Scheme 22). Although this strategy required high pressure, the metal loading of this system was extremely low (0.01%), and the catalyst could be recycled at least 3 times. In the same year, a AgCl/Et 4 NCl system was proposed by Song, Zhang and Hao et al. [96], which could obtain β-oxopropylcarbamates through a milder and easier strategy. In this reaction, β-oxopropylcarbamates were synthesized in moderate to excellent yields at 60 • C and atmospheric CO 2 pressure in CH 3 CN. Yields of products were mainly affected by the steric hindrance effect and the induction effect of the oxygen atom (Scheme 23). Scheme 20. Ag2WO4/Ph3P system catalyzed three-component reaction of propargylic alcohols, CO2 and secondary amines. Driven by these works, ever increasing attention has been paid to developing the reaction conditions' mildness and economy for the reaction system, especially for the low CO2 pressure and recycling performance of the catalyst. In 2018, Zhang and He et al. [72] reported the Ag2CO3/(p-MeOC6H4)3 system for the synthesis of β-oxopropylcarbamates via a one-pot stepwise method. Similar to the abovementioned synthesis method for oxazolidinones, the first step was to generate α-alkylidene cyclic carbonates under 2 MPa of Scheme 20. Ag 2 WO 4 /Ph 3 P system catalyzed three-component reaction of propargylic alcohols, CO 2 and secondary amines. Scheme 20. Ag2WO4/Ph3P system catalyzed three-component reaction of propargylic alcohols, CO2 and secondary amines. Driven by these works, ever increasing attention has been paid to developing the reaction conditions' mildness and economy for the reaction system, especially for the low CO2 pressure and recycling performance of the catalyst. In 2018, Zhang and He et al. [72] reported the Ag2CO3/(p-MeOC6H4)3 system for the synthesis of β-oxopropylcarbamates via a one-pot stepwise method. Similar to the abovementioned synthesis method for oxazolidinones, the first step was to generate α-alkylidene cyclic carbonates under 2 MPa of Scheme 21. (a) Ag 2 CO 3 /Ph 3 P system catalyzed three-component reaction of propargylic alcohols, CO 2 and secondary amines. (b) The proposed catalytic mechanism of the Ag 2 CO 3 /Ph 3 P system. a milder and easier strategy. In this reaction, β-oxopropylcarbamates were synthesized in moderate to excellent yields at 60 °C and atmospheric CO2 pressure in CH3CN. Yields of products were mainly affected by the steric hindrance effect and the induction effect of the oxygen atom (Scheme 23). Recently, our group also achieved significant progress in preparing β-oxopropylcarbamates through this one-pot three-component tandem reaction strategy. For example, in 2018, we reported a green and recyclable catalytic system based on AgBr and an IL of 1ethyl-3-methylimidazolium acetate ([C2C1im][OAc]) for the three-component tandem reaction of propargylic alcohols, secondary amines, and CO2 under atmospheric CO2 pressure without any solvent (Scheme 24a) [97]. Notably, this AgBr/[C2C1im][OAc] system exhibited desirable stability and could be reused at least 5 times. Judging from the yield data, the generation of carbamates was mainly affected by the steric effects of the substituted R1 and R2 groups in the propargylic alcohols. The desired products were obtained in high to excellent yields in the case of most secondary amines. The seldom-reported dissymmetric secondary amine also gave the target product in a moderate yield. Its proposed mechanism is shown in Scheme 24b. Initially, OAc − and secondary amines simultaneously activated CO2 and the hydroxyl groups of substrate 1 (intermediate I) and enhanced the nucleophilicity of the hydroxyl oxygens to the CO2 molecules, leading to the formation of carbonate intermediate II. Subsequently, Ag(I) activated the C≡C bond to facilitate the combination of C−O, generating the five-membered ring III. Afterwards, the catalysts were released from III to form the key intermediate IV. Finally, the secondary amine attacked the carbonyl groups of the intermediate IV to generate the intermediate V, followed by the keto-enol tautomerism and formation of β-oxopropylcarbamates 3. Moreover, N-heterocyclic carbene (NHC) silver complexes were found in this catalytic system, which might be formed by the interaction between C(2) protons and acetate ions, generating free NHC and then reacting with the Ag salt to create the bis-NHC structure (Scheme 24c). a milder and easier strategy. In this reaction, β-oxopropylcarbamates were synthesized in moderate to excellent yields at 60 °C and atmospheric CO2 pressure in CH3CN. Yields of products were mainly affected by the steric hindrance effect and the induction effect of the oxygen atom (Scheme 23). Recently, our group also achieved significant progress in preparing β-oxopropylcarbamates through this one-pot three-component tandem reaction strategy. For example, in 2018, we reported a green and recyclable catalytic system based on AgBr and an IL of 1ethyl-3-methylimidazolium acetate ([C2C1im][OAc]) for the three-component tandem reaction of propargylic alcohols, secondary amines, and CO2 under atmospheric CO2 pressure without any solvent (Scheme 24a) [97]. Notably, this AgBr/[C2C1im][OAc] system exhibited desirable stability and could be reused at least 5 times. Judging from the yield data, the generation of carbamates was mainly affected by the steric effects of the substituted R1 and R2 groups in the propargylic alcohols. The desired products were obtained in high to excellent yields in the case of most secondary amines. The seldom-reported dissymmetric secondary amine also gave the target product in a moderate yield. Its proposed mechanism is shown in Scheme 24b. Initially, OAc − and secondary amines simultaneously activated CO2 and the hydroxyl groups of substrate 1 (intermediate I) and enhanced the nucleophilicity of the hydroxyl oxygens to the CO2 molecules, leading to the formation of carbonate intermediate II. Subsequently, Ag(I) activated the C≡C bond to facilitate the combination of C−O, generating the five-membered ring III. Afterwards, the catalysts were released from III to form the key intermediate IV. Finally, the secondary amine attacked the carbonyl groups of the intermediate IV to generate the intermediate V, followed by the keto-enol tautomerism and formation of β-oxopropylcarbamates 3. Moreover, N-heterocyclic carbene (NHC) silver complexes were found in this catalytic system, which might be formed by the interaction between C(2) protons and acetate ions, generating free NHC and then reacting with the Ag salt to create the bis-NHC structure (Scheme 24c). Recently, our group also achieved significant progress in preparing β-oxopropylcarbamates through this one-pot three-component tandem reaction strategy. For example, in 2018, we reported a green and recyclable catalytic system based on AgBr and an IL of 1-ethyl-3methylimidazolium acetate ([C 2 C 1 im][OAc]) for the three-component tandem reaction of propargylic alcohols, secondary amines, and CO 2 under atmospheric CO 2 pressure without any solvent (Scheme 24a) [97]. Notably, this AgBr/[C 2 C 1 im][OAc] system exhibited desirable stability and could be reused at least 5 times. Judging from the yield data, the generation of carbamates was mainly affected by the steric effects of the substituted R 1 and R 2 groups in the propargylic alcohols. The desired products were obtained in high to excellent yields in the case of most secondary amines. The seldom-reported dissymmetric secondary amine also gave the target product in a moderate yield. Its proposed mechanism is shown in Scheme 24b. Initially, OAc − and secondary amines simultaneously activated CO 2 and the hydroxyl groups of substrate 1 (intermediate I) and enhanced the nucleophilicity of the hydroxyl oxygens to the CO 2 molecules, leading to the formation of carbonate intermediate II. Subsequently, Ag(I) activated the C≡C bond to facilitate the combination of C−O, generating the five-membered ring III. Afterwards, the catalysts were released from III to form the key intermediate IV. Finally, the secondary amine attacked the carbonyl groups of the intermediate IV to generate the intermediate V, followed by the keto-enol tautomerism and formation of β-oxopropylcarbamates 3. Moreover, N-heterocyclic carbene (NHC) silver complexes were found in this catalytic system, which might be formed by the interaction between C(2) protons and acetate ions, generating free NHC and then reacting with the Ag salt to create the bis-NHC structure (Scheme 24c).
Apart from the metal-catalyzed process, the metal-free organocatalytic method was also studied. The Costa group [76] studied the reactions of propargylic alcohols with scCO 2 or in acetonitrile with gaseous CO 2 , employing organic bases as catalysts. They found that bicyclic guanidines such as 1,5,7-triazabicyclo[4.4.0]dec-5-ene (TBD) and 7-Methyl-1,5,7-triazabicyclo[4.4.0]dec-5-ene (MTBD) were effective catalysts for transforming CO 2 into α-alkylidene cyclic carbonates. Based on this, they successfully obtained a range of carbonates in high yields and good selectivity through a one-step three-component tandem reaction of CO 2 , terminal propargylic alcohols and an external N-nucleophiles (secondary amines). According to his results, the catalytic performance of MTBD was better than TBD (Scheme 25). In 2007, Qi and Jiang [98] reported that β-oxopropylcarbamates could be efficiently synthesized in the absence of any additional catalysts and organic solvents in compressed CO 2 with propargylic alcohols, secondary amines. The target products were obtained in 35-88% yields at 130 • C and 14 MPa of CO 2 (Scheme 26). Apart from the metal-catalyzed process, the metal-free organocatalytic method was also studied. The Costa group [76] studied the reactions of propargylic alcohols with scCO2 or in acetonitrile with gaseous CO2, employing organic bases as catalysts. They found that bicyclic guanidines such as 1,5,7-triazabicyclo[4.4.0]dec-5-ene (TBD) and 7-Methyl-1,5,7-triazabicyclo[4.4.0]dec-5-ene (MTBD) were effective catalysts for transforming CO2 into α-alkylidene cyclic carbonates. Based on this, they successfully obtained a range of carbonates in high yields and good selectivity through a one-step three-component tandem reaction of CO2, terminal propargylic alcohols and an external N-nucleophiles (secondary amines). According to his results, the catalytic performance of MTBD was better than TBD (Scheme 25). In 2007, Qi and Jiang [98] reported that β-oxopropylcarbamates could be efficiently synthesized in the absence of any additional catalysts and organic solvents in compressed CO2 with propargylic alcohols, secondary amines. The target products were obtained in 35-88% yields at 130 °C and 14 MPa of CO2 (Scheme 26). Recently, some heterogeneous catalysts were also developed for the target reaction, such as the metal-based nanostructured materials of one-dimensional silver nanowires (Ag NWs) and spherical silver nanoparticles (Ag NPs). Their unique properties (good dispersity and uniformity) and the rapid development of synthesis strategies made it feasible to prepare nanomaterials with different shapes, sizes, structures and tunable compositions [99]. Recently, these kinds of materials were gradually applied in converting CO 2 under environmentally friendly conditions. In 2015, the Han group [100] reported the Ag NPs catalyzed cyclic carboxylation reaction of CO 2 with propargylic alcohols affording α-alkylidene cyclic carbonates. Later, Ag NPs combined with MOF was employed to synthesize propionic acid from terminal alkynes and CO 2 [54,101]. Recently, some heterogeneous catalysts were also developed for the target reaction, such as the metal-based nanostructured materials of one-dimensional silver nanowires (Ag NWs) and spherical silver nanoparticles (Ag NPs). Their unique properties (good dispersity and uniformity) and the rapid development of synthesis strategies made it feasible to prepare nanomaterials with different shapes, sizes, structures and tunable compositions [99]. Recently, these kinds of materials were gradually applied in converting CO2 under environmentally friendly conditions. In 2015, the Han group [100] reported the Ag NPs catalyzed cyclic carboxylation reaction of CO2 with propargylic alcohols affording αalkylidene cyclic carbonates. Later, Ag NPs combined with MOF was employed to synthesize propionic acid from terminal alkynes and CO2 [54,101].
Inspired by these works, Qi and Hu et al. [99] successfully synthesized a diversity of β-oxopropylcarbamates via a three-component coupling reaction of propargylic alcohols, CO2 and secondary amines employing Ag NWs as a catalyst for the first time (Scheme 27). In this reaction, terminal propargylic alcohols with various alkyl or aryl substituents could react with symmetric and asymmetric dialkylamines and amines with long alkyl chains to afford target products with good to excellent yields under 1 MPa of CO2 in CH3CN with DMAP as an additive. Moreover, Ag NWs could be easily recycled by centrifugation and reused at least 4 times. In 2019, Chang and Sadeghzadeh et al. [102] developed ionic gelation (IG) (of TPP and spirulina) related catalyst (DFNS/IG-Ag(I) NPs) for the one-pot synthesis of β-oxopropylcarbamates through the three-component tandem reaction of propargylic alcohols, CO2 and secondary amines at 50 °C and 1.5 MPa of CO2 (Scheme 28). The yields of carbamates were mainly affected by steric hindrance of the substituents in propargylic alcohols or amines. Notably, this catalyst could be recycled 5 times. In the proposed catalytic mechanism, spirulina and TPP synergistically activated the hydroxyl groups of propargyl alcohols. Simultaneously, CO2 was captured and activated by the synergistic effects of TPP and spirulina. Afterwards, Ag(I) species activated the C≡C bonds to facilitate the combination of the negatively charged oxygen atoms with the carbons in the triple bonds, leading to the formation of the five-membered rings. Subsequently, the catalysts were released from the five-membered ring to form the cyclic carbonate intermediate. Finally, the secondary amine attacked the carbonyl groups of the cyclic carbonate intermediates, followed by the keto-enol tautomerism and formation of β-oxopropylcarbamates.  Recently, some heterogeneous catalysts were also developed for the target reaction, such as the metal-based nanostructured materials of one-dimensional silver nanowires (Ag NWs) and spherical silver nanoparticles (Ag NPs). Their unique properties (good dispersity and uniformity) and the rapid development of synthesis strategies made it feasible to prepare nanomaterials with different shapes, sizes, structures and tunable compositions [99]. Recently, these kinds of materials were gradually applied in converting CO2 under environmentally friendly conditions. In 2015, the Han group [100] reported the Ag NPs catalyzed cyclic carboxylation reaction of CO2 with propargylic alcohols affording αalkylidene cyclic carbonates. Later, Ag NPs combined with MOF was employed to synthesize propionic acid from terminal alkynes and CO2 [54,101].
Inspired by these works, Qi and Hu et al. [99] successfully synthesized a diversity of β-oxopropylcarbamates via a three-component coupling reaction of propargylic alcohols, CO2 and secondary amines employing Ag NWs as a catalyst for the first time (Scheme 27). In this reaction, terminal propargylic alcohols with various alkyl or aryl substituents could react with symmetric and asymmetric dialkylamines and amines with long alkyl chains to afford target products with good to excellent yields under 1 MPa of CO2 in CH3CN with DMAP as an additive. Moreover, Ag NWs could be easily recycled by centrifugation and reused at least 4 times. In 2019, Chang and Sadeghzadeh et al. [102] developed ionic gelation (IG) (of TPP and spirulina) related catalyst (DFNS/IG-Ag(I) NPs) for the one-pot synthesis of β-oxopropylcarbamates through the three-component tandem reaction of propargylic alcohols, CO2 and secondary amines at 50 °C and 1.5 MPa of CO2 (Scheme 28). The yields of carbamates were mainly affected by steric hindrance of the substituents in propargylic alcohols or amines. Notably, this catalyst could be recycled 5 times. In the proposed catalytic mechanism, spirulina and TPP synergistically activated the hydroxyl groups of propargyl alcohols. Simultaneously, CO2 was captured and activated by the synergistic effects of TPP and spirulina. Afterwards, Ag(I) species activated the C≡C bonds to facilitate the combination of the negatively charged oxygen atoms with the carbons in the triple bonds, leading to the formation of the five-membered rings. Subsequently, the catalysts were released from the five-membered ring to form the cyclic carbonate intermediate. Finally, the secondary amine attacked the carbonyl groups of the cyclic carbonate intermediates, followed by the keto-enol tautomerism and formation of β-oxopropylcarbamates. Inspired by these works, Qi and Hu et al. [99] successfully synthesized a diversity of β-oxopropylcarbamates via a three-component coupling reaction of propargylic alcohols, CO 2 and secondary amines employing Ag NWs as a catalyst for the first time (Scheme 27). In this reaction, terminal propargylic alcohols with various alkyl or aryl substituents could react with symmetric and asymmetric dialkylamines and amines with long alkyl chains to afford target products with good to excellent yields under 1 MPa of CO 2 in CH 3 CN with DMAP as an additive. Moreover, Ag NWs could be easily recycled by centrifugation and reused at least 4 times. In 2019, Chang and Sadeghzadeh et al. [102] developed ionic gelation (IG) (of TPP and spirulina) related catalyst (DFNS/IG-Ag(I) NPs) for the one-pot synthesis of β-oxopropylcarbamates through the three-component tandem reaction of propargylic alcohols, CO 2 and secondary amines at 50 • C and 1.5 MPa of CO 2 (Scheme 28). The yields of carbamates were mainly affected by steric hindrance of the substituents in propargylic alcohols or amines. Notably, this catalyst could be recycled 5 times. In the proposed catalytic mechanism, spirulina and TPP synergistically activated the hydroxyl groups of propargyl alcohols. Simultaneously, CO 2 was captured and activated by the synergistic effects of TPP and spirulina. Afterwards, Ag(I) species activated the C≡C bonds to facilitate the combination of the negatively charged oxygen atoms with the carbons in the triple bonds, leading to the formation of the five-membered rings. Subsequently, the catalysts were released from the five-membered ring to form the cyclic carbonate intermediate. Finally, the secondary amine attacked the carbonyl groups of the cyclic carbonate intermediates, followed by the keto-enol tautomerism and formation of β-oxopropylcarbamates.
In the same year, Fan et al. [103] developed a unique bifunctional hybrid catalyst (TEMPO-FPS-laccase NPs) through co-immobilization of 2,2,6,6-tetra-methylpiperidine-1oxyl (TEMPO) and laccase in the same cavities into glycidyloxypropyl functionalized fibrous phosphosilicate (FPS) nanoparticles (Scheme 29a). This catalyst was applied for the one-pot synthesis β-oxopropylcarbamates via a three-component tandem reaction of propargylic alcohols, CO 2 , and secondary amines employing water as the solvent under 1.5 MPa of CO 2 (Scheme 29b). The yields of the corresponding carbamates ranged from 48-97%. Although the system required relatively high CO 2 pressure, this heterogeneous biocatalyst was truly attractive due to its environmentally friendly characters such as superior storage stability, easy separation and remarkable recyclability, which could be reused at least 10 times by extremely low catalyst loading. The remarkable cycle performances were mainly attributed to the FPS nanostructure, while the excellent catalytic performances were determined by the use of enzymes. Similar to the above mechanism, this production of βoxopropylcarbamates also proceeded with the formation of αalkylidene cyclic carbonate, nucleophilic attack of amine, and keto-enol tautomerism. In 2020, Hassan et al. [104] reported that in the presence of a new magnetic nano-catalyst, palladium NPs supported on magnetic fibrous silica ionic gelation (FeNi 3 /DFNS/IG/Pd MNPs), β-oxopropylcarbamates were synthesized through a three-component tandem reaction of propargylic alcohols, CO 2 and secondary amines in 54-98% yields at 70 • C and 2 MPa of CO 2 with water as a solvent. Moreover, this nano-catalyst can be recycled at least 10 times (Scheme 30).
used at least 10 times by extremely low catalyst loading. The remarkable cycle performances were mainly attributed to the FPS nanostructure, while the excellent catalytic performances were determined by the use of enzymes. Similar to the above mechanism, this production of β-oxopropylcarbamates also proceeded with the formation of α-alkylidene cyclic carbonate, nucleophilic attack of amine, and keto-enol tautomerism. In 2020, Hassan et al. [104] reported that in the presence of a new magnetic nano-catalyst, palladium NPs supported on magnetic fibrous silica ionic gelation (FeNi3/DFNS/IG/Pd MNPs), β-oxopropylcarbamates were synthesized through a three-component tandem reaction of propargylic alcohols, CO2 and secondary amines in 54-98% yields at 70°C and 2 MPa of CO2 with water as a solvent. Moreover, this nano-catalyst can be recycled at least 10 times (Scheme 30).
In the past decades, graphene has been widely used as a favorable supporter for metal or metal-oxide nanoparticles due to its large specific surface area [105,106], excellent dispersion for metal particles, and superior stability [107][108][109]. Based on this, a more gentle strategy was developed by He et al. [109]. They reported the graphene oxide (rGO) supported Ag NPs catalysts (Ag-rGO) for the efficient transformation of CO2 at ambient conditions. Target β-oxopropylcarbamates could be obtained smoothly from the reaction of 2-methyl-3-butyn-2-ol, diethylamine, and CO2 in 86% yield under atmospheric CO2 pressure in the presence of Ag-rGO and [N4444] [Triz]. Additionally, the robust stability of Ag-rGO enables its structure and activity to be maintained after 5 cycles (Scheme 31).  used at least 10 times by extremely low catalyst loading. The remarkable cycle performances were mainly attributed to the FPS nanostructure, while the excellent catalytic performances were determined by the use of enzymes. Similar to the above mechanism, this production of β-oxopropylcarbamates also proceeded with the formation of α-alkylidene cyclic carbonate, nucleophilic attack of amine, and keto-enol tautomerism. In 2020, Hassan et al. [104] reported that in the presence of a new magnetic nano-catalyst, palladium NPs supported on magnetic fibrous silica ionic gelation (FeNi3/DFNS/IG/Pd MNPs), β-oxopropylcarbamates were synthesized through a three-component tandem reaction of propargylic alcohols, CO2 and secondary amines in 54-98% yields at 70°C and 2 MPa of CO2 with water as a solvent. Moreover, this nano-catalyst can be recycled at least 10 times (Scheme 30).
In the past decades, graphene has been widely used as a favorable supporter for metal or metal-oxide nanoparticles due to its large specific surface area [105,106], excellent dispersion for metal particles, and superior stability [107][108][109]. Based on this, a more gentle strategy was developed by He et al. [109]. They reported the graphene oxide (rGO) supported Ag NPs catalysts (Ag-rGO) for the efficient transformation of CO2 at ambient conditions. Target β-oxopropylcarbamates could be obtained smoothly from the reaction of 2-methyl-3-butyn-2-ol, diethylamine, and CO2 in 86% yield under atmospheric CO2 pressure in the presence of Ag-rGO and [N4444] [Triz]. Additionally, the robust stability of Ag-rGO enables its structure and activity to be maintained after 5 cycles (Scheme 31).

Three-Component Reactions of Propargylic Alcohols, CO2 and H2O
Since Kutscheroff developed the Hg(II) salts/H2SO4 catalytic system for the hydration of alkynes [110,111], great efforts have been devoted to a mercury-free route to obtain versatile carbonyl compounds [112][113][114]. Hydration of propargylic alcohols is a straightforward method to generate α-hydroxy ketones, which are vital skeletons in various drugs and natural products [115][116][117]. However, the direct hydration of propargylic alcohols to prepare α-hydroxy ketones was not an ideal route, owing to the formation of byproducts resulting from the Meyer-Schuster and Rupe rearrangements [118,119]. Therefore, a more efficient and eco-friendly reaction route has been developed, employing CO2 as a promoter for hydrating propargylic alcohols and H2O. The procedures of this threecomponent reaction were involved with the generation of α-alkylidene cyclic carbonates, in situ hydrolysis and the keto−enol tautomerization to afford the desired α-hydroxy ketones (Scheme 32). In the overall cycle, CO2 was not consumed and acted as a co-catalyst. In the past decades, graphene has been widely used as a favorable supporter for metal or metal-oxide nanoparticles due to its large specific surface area [105,106], excellent dispersion for metal particles, and superior stability [107][108][109]. Based on this, a more gentle strategy was developed by He et al. [109]. They reported the graphene oxide (rGO) supported Ag NPs catalysts (Ag-rGO) for the efficient transformation of CO 2 at ambient conditions. Target β-oxopropylcarbamates could be obtained smoothly from the reaction of 2-methyl-3-butyn-2-ol, diethylamine, and CO 2 in 86% yield under atmospheric CO 2 pressure in the presence of Ag-rGO and [N 4444 ][Triz]. Additionally, the robust stability of Ag-rGO enables its structure and activity to be maintained after 5 cycles (Scheme 31).

Three-Component Reactions of Propargylic Alcohols, CO2 and H2O
Since Kutscheroff developed the Hg(II) salts/H2SO4 catalytic system for the hydration of alkynes [110,111], great efforts have been devoted to a mercury-free route to obtain versatile carbonyl compounds [112][113][114]. Hydration of propargylic alcohols is a straightforward method to generate α-hydroxy ketones, which are vital skeletons in various drugs and natural products [115][116][117]. However, the direct hydration of propargylic alcohols to prepare α-hydroxy ketones was not an ideal route, owing to the formation of byproducts resulting from the Meyer-Schuster and Rupe rearrangements [118,119]. Therefore, a more efficient and eco-friendly reaction route has been developed, employing CO2 as a promoter for hydrating propargylic alcohols and H2O. The procedures of this threecomponent reaction were involved with the generation of α-alkylidene cyclic carbonates, in situ hydrolysis and the keto−enol tautomerization to afford the desired α-hydroxy ketones (Scheme 32). In the overall cycle, CO2 was not consumed and acted as a co-catalyst.

Three-Component Reactions of Propargylic Alcohols, CO 2 and H 2 O
Since Kutscheroff developed the Hg(II) salts/H 2 SO 4 catalytic system for the hydration of alkynes [110,111], great efforts have been devoted to a mercury-free route to obtain versatile carbonyl compounds [112][113][114]. Hydration of propargylic alcohols is a straightforward method to generate α-hydroxy ketones, which are vital skeletons in various drugs and natural products [115][116][117]. However, the direct hydration of propargylic alcohols to prepare α-hydroxy ketones was not an ideal route, owing to the formation of byproducts resulting from the Meyer-Schuster and Rupe rearrangements [118,119]. Therefore, a more efficient and eco-friendly reaction route has been developed, employing CO 2 as a promoter for hydrating propargylic alcohols and H 2 O. The procedures of this three-component reaction were involved with the generation of α-alkylidene cyclic carbonates, in situ hydrolysis and the keto−enol tautomerization to afford the desired α-hydroxy ketones (Scheme 32). In the overall cycle, CO 2 was not consumed and acted as a co-catalyst. Transition-metal compounds such as Ag and Cu salts are favorable catalysts for the CO2-promoted hydration of propargylic alcohols. In 2014, Qi et al. [40] reported that the CO2-promoted process could proceed smoothly in the presence of AgOAc and DBU under 2 MPa of CO2 in a mixed acetonitrile/water solvent. Both the internal and terminal propargylic alcohols could produce the target products in good yields (Scheme 33). In 2018, Song and Liu et al. [46] discovered that α-hydroxy ketones could be efficiently produced in the presence of ZnCl2 and DBU under 1 MPa of CO2 in CH3CN (Scheme 34). In 2019, Scheme 32. The process of CO 2 -promoted hydration of propargylic alcohols.
Transition-metal compounds such as Ag and Cu salts are favorable catalysts for the CO 2 -promoted hydration of propargylic alcohols. In 2014, Qi et al. [40] reported that the CO 2 -promoted process could proceed smoothly in the presence of AgOAc and DBU under 2 MPa of CO 2 in a mixed acetonitrile/water solvent. Both the internal and terminal propargylic alcohols could produce the target products in good yields (Scheme 33). In 2018, Song and Liu et al. [46] discovered that α-hydroxy ketones could be efficiently produced in the presence of ZnCl 2 and DBU under 1 MPa of CO 2 in CH 3 CN (Scheme 34). In 2019, Chen et al. [42] developed a Cu 2 O/DBU system that could efficiently transform a range of propargylic alcohols into desired α-hydroxy ketones under atmospheric CO 2 pressure in CH 3 CN employing cyclohexyldiphenylphosphine as an additive (Scheme 35). the CO2-promoted hydration of propargylic alcohols to afford α-hydroxy ketones under atmospheric CO2 pressure and solvent-free condition (Scheme 36a) [43]. Diverse propargylic alcohols could be transformed into target hydroxy ketones in excellent yields with the catalysis of only a trace amount of silver (0.005−0.25 mol %). Notably, this system could be reused at least 5 times. Furthermore, an unprecedented turnover number (TON) of 9200 was obtained. The proposed catalytic mechanism of the AgOAc/[Emim][OAc] system is shown in Scheme 36b. Firstly, the highly concentrated [OAc] simultaneously activated CO2 and the hydroxyl groups from substrates 1, inducing the following nucleophilic attack and formation of intermediates II. Afterward, Ag species activated the C≡C bonds to promote the formation of the C−O bonds, resulting in the creation of five-membered rings III. Then, the catalysts were released and the key α-alkylidene cyclic carbonates IV were generated. Subsequently, water molecules acted as nucleophiles and attacked the carbonyls of α-alkylidene cyclic carbonates IV to generate the intermediates V with the catalysis of the basic ILs, followed by the keto-enol tautomerism. Finally, one equivalent of CO2 was released and the desired ketone 2 was formed. the CO2-promoted hydration of propargylic alcohols to afford α-hydroxy ketones under atmospheric CO2 pressure and solvent-free condition (Scheme 36a) [43]. Diverse propargylic alcohols could be transformed into target hydroxy ketones in excellent yields with the catalysis of only a trace amount of silver (0.005−0.25 mol %). Notably, this system could be reused at least 5 times. Furthermore, an unprecedented turnover number (TON) of 9200 was obtained. The proposed catalytic mechanism of the AgOAc/[Emim][OAc] system is shown in Scheme 36b. Firstly, the highly concentrated [OAc] simultaneously activated CO2 and the hydroxyl groups from substrates 1, inducing the following nucleophilic attack and formation of intermediates II. Afterward, Ag species activated the C≡C bonds to promote the formation of the C−O bonds, resulting in the creation of five-membered rings III. Then, the catalysts were released and the key α-alkylidene cyclic carbonates IV were generated. Subsequently, water molecules acted as nucleophiles and attacked the carbonyls of α-alkylidene cyclic carbonates IV to generate the intermediates V with the catalysis of the basic ILs, followed by the keto-enol tautomerism. Finally, one equivalent of CO2 was released and the desired ketone 2 was formed. In order to synthesize α-hydroxy ketones through a greener route, our group developed an effective AgOAc/1-ethyl-3-methylimidazolium acetate ([Emim][OAc]) system for the CO 2 -promoted hydration of propargylic alcohols to afford α-hydroxy ketones under atmospheric CO 2 pressure and solvent-free condition (Scheme 36a) [43]. Diverse propargylic alcohols could be transformed into target hydroxy ketones in excellent yields with the catalysis of only a trace amount of silver (0.005−0.25 mol %). Notably, this system could be reused at least 5 times. Furthermore, an unprecedented turnover number (TON) of 9200 was obtained. The proposed catalytic mechanism of the AgOAc/[Emim][OAc] system is shown in Scheme 36b. Firstly, the highly concentrated [OAc] simultaneously activated CO 2 and the hydroxyl groups from substrates 1, inducing the following nucleophilic attack and formation of intermediates II. Afterward, Ag species activated the C≡C bonds to promote the formation of the C−O bonds, resulting in the creation of five-membered rings III. Then, the catalysts were released and the key α-alkylidene cyclic carbonates IV were generated. Subsequently, water molecules acted as nucleophiles and attacked the carbonyls of α-alkylidene cyclic carbonates IV to generate the intermediates V with the catalysis of the basic ILs, followed by the keto-enol tautomerism. Finally, one equivalent of CO 2 was released and the desired ketone 2 was formed. In 2015, Liu et al. [41] reported a metal-free catalytic system for hydrating propargylic alcohols and H2O with CO2 as a co-catalyst to produce α-hydroxy ketones at atmospheric CO2 pressure (Scheme 37). A series of desired products could be obtained in good to excellent yields in the presence of tetrabutylphosphonium imidazole (

Three-Component Reactions of Propargylic Alcohols, CO2 and Monohydric Alcohols
As weak nucleophiles, monohydric alcohols could also react with propargylic alcohols and CO2, affording β-oxoalkyl carbonates, which are a kind of dissymmetric carbonate and generally used as important reagents and intermediates in organic synthesis [120,121]. The three-component reaction of propargylic alcohols, CO2 and monohydric alcohols could proceed smoothly through the sequential steps of carboxylative cyclization, nucleophilic attack of monohydric alcohols, and tautomerization (Scheme 38).

Three-Component Reactions of Propargylic Alcohols, CO 2 and Monohydric Alcohols
As weak nucleophiles, monohydric alcohols could also react with propargylic alcohols and CO 2 , affording β-oxoalkyl carbonates, which are a kind of dissymmetric carbonate and generally used as important reagents and intermediates in organic synthesis [120,121]. The three-component reaction of propargylic alcohols, CO 2 and monohydric alcohols could proceed smoothly through the sequential steps of carboxylative cyclization, nucleophilic attack of monohydric alcohols, and tautomerization (Scheme 38).

Three-Component Reactions of Propargylic Alcohols, CO2 and Monohydric Alcohols
As weak nucleophiles, monohydric alcohols could also react with propargylic alcohols and CO2, affording β-oxoalkyl carbonates, which are a kind of dissymmetric carbonate and generally used as important reagents and intermediates in organic synthesis [120,121]. The three-component reaction of propargylic alcohols, CO2 and monohydric alcohols could proceed smoothly through the sequential steps of carboxylative cyclization, nucleophilic attack of monohydric alcohols, and tautomerization (Scheme 38). Dixneuf et al. [122] initially first synthesized cyclic carbonates using tributylphosphine as a catalyst. Then these cyclic carbonates react with monohydric alcohols to afford desired dissymmetric carbonates in the presence of triethylamine or KCN (Scheme 39). Later, the Costa group [76] developed the one-pot synthesis strategy to obtain β-oxoalkyl carbonates through the three-component reaction of propargylic alcohols, CO2 and monohydric alcohols employing bicyclic guanidines as catalysts under scCO2 conditions. Dixneuf et al. [122] initially first synthesized cyclic carbonates using tributylphosphine as a catalyst. Then these cyclic carbonates react with monohydric alcohols to afford desired dissymmetric carbonates in the presence of triethylamine or KCN (Scheme 39). Later, the Costa group [76] developed the one-pot synthesis strategy to obtain β-oxoalkyl carbonates through the three-component reaction of propargylic alcohols, CO 2 and monohydric alcohols employing bicyclic guanidines as catalysts under scCO 2 conditions.

Three-Component Reactions of Propargylic Alcohols, CO2 and Monohydric Alcohols
As weak nucleophiles, monohydric alcohols could also react with propargylic alcohols and CO2, affording β-oxoalkyl carbonates, which are a kind of dissymmetric carbonate and generally used as important reagents and intermediates in organic synthesis [120,121]. The three-component reaction of propargylic alcohols, CO2 and monohydric alcohols could proceed smoothly through the sequential steps of carboxylative cyclization, nucleophilic attack of monohydric alcohols, and tautomerization (Scheme 38). Scheme 38. The process of the three-component reaction of propargylic alcohols, CO2 and monohydric alcohols.
Dixneuf et al. [122] initially first synthesized cyclic carbonates using tributylphosphine as a catalyst. Then these cyclic carbonates react with monohydric alcohols to afford desired dissymmetric carbonates in the presence of triethylamine or KCN (Scheme 39). Later, the Costa group [76] developed the one-pot synthesis strategy to obtain β-oxoalkyl carbonates through the three-component reaction of propargylic alcohols, CO2 and monohydric alcohols employing bicyclic guanidines as catalysts under scCO2 conditions. Scheme 39. Two step strategy for the three-component reaction of propargylic alcohols, CO2 and monohydric alcohols.
In recent years, silver and zinc compounds have been developed as excellent catalysts for this three-component reaction. In 2016, He et al. [44] reported an effective Ag2CO3 In recent years, silver and zinc compounds have been developed as excellent catalysts for this three-component reaction. In 2016, He et al. [44] reported an effective Ag 2 CO 3 /Ph 3   Although the above strategies could effectively synthesize β-oxoalkyl carbonates, several drawbacks remain, such as high CO 2 pressure, narrow substrate scope, etc. To improve the reaction conditions, Song and Zhang et al. [47] developed a synergistic silver sulfadiazine/ n Bu 4 NBr system for the one-pot synthesis of β-oxopropyl carbonates under atmospheric CO 2 pressure and solvent-free conditions (Scheme 43). Additionally, this protocol showed excellent tolerance for a wide range of propargyl alcohols and monohydric alcohols. Various desired carbonates could be obtained in 64-99% yields, although phenol failed to afford the target product, and an excess amount of alcohol was generally required. Furthermore, they speculated that the excellent catalytic performance was attributed to the synergistic catalysis of silver sulfadiazine and n Bu 4 NBr. In 2020, Detrembleur et al. [51] proposed a AgI/tetrabutylammonium phenolate ([TBA][OPh]) catalytic system, which was highly active for this one-pot process (Scheme 44). Most of the desired products could be obtained in more than 97% yields under atmospheric CO 2 pressure in DMSO. The yield data further demonstrated that primary monohydric alcohols were more active than secondary or tertiary monohydric alcohols. Notably, the authors explored the kinetic insights and the catalytic mechanism through FT-IR spectroscopy and density functional theory (DFT) calculations. Although the above strategies could effectively synthesize β-oxoalkyl carbonates, several drawbacks remain, such as high CO2 pressure, narrow substrate scope, etc. To improve the reaction conditions, Song and Zhang et al. [47] developed a synergistic silver sulfadiazine/ n Bu4NBr system for the one-pot synthesis of β-oxopropyl carbonates under atmospheric CO2 pressure and solvent-free conditions (Scheme 43). Additionally, this protocol showed excellent tolerance for a wide range of propargyl alcohols and monohydric alcohols. Various desired carbonates could be obtained in 64-99% yields, although phenol failed to afford the target product, and an excess amount of alcohol was generally required. Furthermore, they speculated that the excellent catalytic performance was attributed to the synergistic catalysis of silver sulfadiazine and n Bu4NBr. In 2020, Detrembleur et al. [51] proposed a AgI/tetrabutylammonium phenolate ([TBA][OPh]) catalytic system, which was highly active for this one-pot process (Scheme 44). Most of the desired products could be obtained in more than 97% yields under atmospheric CO2 pressure in DMSO. The yield data further demonstrated that primary monohydric alcohols were more active than secondary or tertiary monohydric alcohols. Notably, the authors explored the kinetic insights and the catalytic mechanism through FT-IR spectroscopy and density functional theory (DFT) calculations.  Although the above strategies could effectively synthesize β-oxoalkyl carbonates, several drawbacks remain, such as high CO2 pressure, narrow substrate scope, etc. To improve the reaction conditions, Song and Zhang et al. [47] developed a synergistic silver sulfadiazine/ n Bu4NBr system for the one-pot synthesis of β-oxopropyl carbonates under atmospheric CO2 pressure and solvent-free conditions (Scheme 43). Additionally, this protocol showed excellent tolerance for a wide range of propargyl alcohols and monohydric alcohols. Various desired carbonates could be obtained in 64-99% yields, although phenol failed to afford the target product, and an excess amount of alcohol was generally required. Furthermore, they speculated that the excellent catalytic performance was attributed to the synergistic catalysis of silver sulfadiazine and n Bu4NBr. In 2020, Detrembleur et al. [51] proposed a AgI/tetrabutylammonium phenolate ([TBA][OPh]) catalytic system, which was highly active for this one-pot process (Scheme 44). Most of the desired products could be obtained in more than 97% yields under atmospheric CO2 pressure in DMSO. The yield data further demonstrated that primary monohydric alcohols were more active than secondary or tertiary monohydric alcohols. Notably, the authors explored the kinetic insights and the catalytic mechanism through FT-IR spectroscopy and density functional theory (DFT) calculations. Recently, natural minerals have also been designed as catalysts for the transformation of CO2. In 2020, Liu et al. [50] loaded silver on attapulgite (ATP) material, a hydrous silicate clay mineral-rich in Mg and Al with a fibrous morphology and demonstrated a certain adsorption effect on CO2. This effective Ag/ATP nanocomposite catalyst was applied for the one-pot synthesis of non-symmetric carbonates through the threecomponent reaction of propargylic alcohols, CO2 and monohydric alcohols (Scheme 45a). The desired β-oxoalkyl carbonates were obtained in low to high yields under 1 MPa of CO2 in DMF with 1,5-diazabicyclo[4.3.0]non-5-ene (DBN) as a co-catalyst. Moreover, the yields were largely influenced by the electron-donating effect of R3 in alcohols. In the in-Scheme 43. Silver sulfadiazine/ n Bu 4 NBr system catalyzed three-component reaction of propargylic alcohols, CO 2 and monohydric alcohols. Recently, natural minerals have also been designed as catalysts for the transformation of CO2. In 2020, Liu et al. [50] loaded silver on attapulgite (ATP) material, a hydrous silicate clay mineral-rich in Mg and Al with a fibrous morphology and demonstrated a certain adsorption effect on CO2. This effective Ag/ATP nanocomposite catalyst was applied for the one-pot synthesis of non-symmetric carbonates through the threecomponent reaction of propargylic alcohols, CO2 and monohydric alcohols (Scheme 45a). The desired β-oxoalkyl carbonates were obtained in low to high yields under 1 MPa of CO2 in DMF with 1,5-diazabicyclo[4.3.0]non-5-ene (DBN) as a co-catalyst. Moreover, the yields were largely influenced by the electron-donating effect of R3 in alcohols. In the in- Recently, natural minerals have also been designed as catalysts for the transformation of CO 2 . In 2020, Liu et al. [50] loaded silver on attapulgite (ATP) material, a hydrous silicate clay mineral-rich in Mg and Al with a fibrous morphology and demonstrated a certain adsorption effect on CO 2 . This effective Ag/ATP nanocomposite catalyst was applied for the one-pot synthesis of non-symmetric carbonates through the three-component reaction of propargylic alcohols, CO 2 and monohydric alcohols (Scheme 45a). The desired βoxoalkyl carbonates were obtained in low to high yields under 1 MPa of CO 2 in DMF with 1,5-diazabicyclo [4.3.0]non-5-ene (DBN) as a co-catalyst. Moreover, the yields were largely influenced by the electron-donating effect of R 3 in alcohols. In the investigations on recyclability, the authors found that Ag/ATP could be recycled at least 10 times by increasing the reaction temperature to decompose the produced carbonates coated on the catalyst's surface. Regarding the catalytic mechanism, the hydroxyl protons in propargyl alcohols firstly interacted with DBN to form [DBNH] + . Then the adsorbed CO 2 on the ATP was attacked by the hydroxyl and oxygen anions to form intermediates II. Subsequently, the silver nanoparticles on the ATP activated the C≡C to promote the connections of the oxygen atoms from the CO 2 to the carbon atoms in the triple bonds, resulting in the formation of five-membered rings III. Afterward, intermediates III received the protons from [HDBN] + and gave the key α-alkylidene cyclic carbonates IV. Eventually, DBN activated the hydroxyl groups in monohydric alcohols to attack the carbonyl groups of the cyclic carbonates IV to produce intermediates V. The target β-oxoalkyl carbonates 3 were finally formed by the following tautomerism (Scheme 45b).

Three-Component Reactions of Propargylic Alcohols, CO2 and Bi-Nucleophiles
In the area of CCU, the condensation of vicinal diols or 2-aminoethanols with CO2 has attracted significant attention. Many strategies have been reported for this reaction to afford the corresponding cyclic carbonates or 2-oxazolidinones, which are a series of highvalue chemical intermediates [124][125][126][127][128][129][130]. Unfortunately, these condensations are usually incomplete due to the thermodynamic limitations and invalidation of catalysts caused by

Three-Component Reactions of Propargylic Alcohols, CO 2 and Bi-Nucleophiles
In the area of CCU, the condensation of vicinal diols or 2-aminoethanols with CO 2 has attracted significant attention. Many strategies have been reported for this reaction to afford the corresponding cyclic carbonates or 2-oxazolidinones, which are a series of high-value chemical intermediates [124][125][126][127][128][129][130]. Unfortunately, these condensations are usually incomplete due to the thermodynamic limitations and invalidation of catalysts caused by the formation of by-products such as water. Although dehydrating agents are typically applied to overcome the equilibrium limitation [126,127,130], the other byproducts derived from the consumed additives still remained in this process [58]. As a result, the yields of desired products in these reactions were usually unsatisfactory even under harsh reaction conditions, which largely limits its practical application. Delightedly, a significant breakthrough has been achieved recently. Scientists revealed that introducing propargylic alcohols into these reactions could effectively avoid the formation of water and bypass the thermodynamic limitation. In this method, the reverse reactions were completely suppressed due to the low nucleophilicity of the generated α-hydroxy ketone [45,49,53]. More importantly, these three-component reactions of propargylic alcohols, CO 2 and vicinal diols or 2-aminoethanols could simultaneously afford the high-value products of cyclic carbonates or 2-oxazolidinones. Regarding the mechanism, this thermodynamically favorable process undertook a two-step procedure: (1) the formation of α-alkylidene cyclic carbonate intermediates M1 from the carboxylative cyclization of propargylic alcohols and CO 2 ; (2) the nucleophilic ring-opening reaction of intermediates M1 and vicinal diols or 2-aminoethanols to produce M2 or M3, followed by the generation of cyclic carbonates 2 or 2-oxazolidinones 3 with 1 equiv. of α-hydroxyl ketones through intramolecular nucleophilic cyclization (Scheme 46).

Vicinal Diols as Bi-Nucleophiles
In the past few years, considerable progress on metal-catalyzed systems for this reaction has been achieved. In 2017, He et al. [45] first proposed a Ag(Ⅰ)-catalyzed system for this three-component reaction of propargylic alcohols, CO2 and vicinal diols to afford cyclic carbonates and α-hydroxyl ketones with an electron-rich bidentate phosphine 4,5-Bis(diphenylphosphino)-9,9-dimethylxanthene (Xantphos) as an additive (Scheme 47). They proved this process was a thermodynamically favorable route through DFT calculations, in which desired products could be obtained in good to excellent yields under 1 MPa of CO2 in CH3CN catalyzed by the Ag2CO3/Xantphos system. Subsequently, Song and Liu et al. [46] developed a Zn(Ⅱ)-catalyzed system for this three-component reaction (Scheme 48) in 2018. Target products could be obtained in excellent yields under 1 or 2 MPa in CH3CN. However, an excess of vicinal diols (1.5 equiv.) was required. Moreover, both of these routes required solvents and high CO2 pressure.
In 2019, Song and Zhang et al. [48] developed an efficient silver sulfadiazine/Et4NBr synergistic catalytic system, enabling this three-component reaction to proceed smoothly under atmospheric CO2 pressure and solvent-free conditions (Scheme 49a). Furthermore, this catalytic system exhibited a broad substrate scope. Propargylic alcohols with different alkyl substituents, including long-chain alkyl, isopropyl, cyclohexyl, vinyl, and phenyl, could react smoothly with 1,2-diols bearing short-or long-chain alkyl and sterically hin-

Vicinal Diols as Bi-Nucleophiles
In the past few years, considerable progress on metal-catalyzed systems for this reaction has been achieved. In 2017, He et al. [45] first proposed a Ag(I)-catalyzed system for this three-component reaction of propargylic alcohols, CO 2 and vicinal diols to afford cyclic carbonates and α-hydroxyl ketones with an electron-rich bidentate phosphine 4,5-Bis(diphenylphosphino)-9,9-dimethylxanthene (Xantphos) as an additive (Scheme 47). They proved this process was a thermodynamically favorable route through DFT calculations, in which desired products could be obtained in good to excellent yields under 1 MPa of CO 2 in CH 3 CN catalyzed by the Ag 2 CO 3 /Xantphos system. Subsequently, Song and Liu et al. [46] developed a Zn(II)-catalyzed system for this three-component reaction (Scheme 48) in 2018. Target products could be obtained in excellent yields under 1 or 2 MPa in CH 3 CN. However, an excess of vicinal diols (1.5 equiv.) was required. Moreover, both of these routes required solvents and high CO 2 pressure.
In 2019, Song and Zhang et al. [48] developed an efficient silver sulfadiazine/Et 4 NBr synergistic catalytic system, enabling this three-component reaction to proceed smoothly under atmospheric CO 2 pressure and solvent-free conditions (Scheme 49a). Furthermore, this catalytic system exhibited a broad substrate scope. Propargylic alcohols with different alkyl substituents, including long-chain alkyl, isopropyl, cyclohexyl, vinyl, and phenyl, could react smoothly with 1,2-diols bearing short-or long-chain alkyl and sterically hindered substituents. The corresponding cyclic carbonates and α-hydroxyl ketones were obtained in satisfactory yields under optimal conditions. Moreover, a plausible mechanism was speculated, as shown in Scheme 49b. Initially, sulfadiazine and Ag species simultaneously activated −OH and C≡C of the propargylic alcohols to form the carbonate intermediates II. Significantly, Et 4 N + stabilized the carbonate intermediates II and enhanced the nucleophilicity of the oxygen atoms. Then, the catalysts were released and the cyclic carbonates III were generated. Afterward, the activated −OH from vicinal diols attacked the carbonyl groups of intermediates III to produce intermediates IV. Eventually, the target cyclic carbonates 3 were produced through the intramolecular nucleophilic cyclization with 1 equiv. of α-hydroxyl ketones 4 released from the skeletons.
Regarding organocatalysis, strong bases such as DBU, TBD, and MTBD, etc., are beneficial for the activation of CO 2 and hydroxyl groups due to their rich electronegativity [52]. Based on this, Song and Liu et al. [52] reported a facile metal-free DBU-catalyzed strategy for the one-pot preparation of cyclic carbonates and α-hydroxy ketones from propargylic alcohols, CO 2 and vicinal diols. However, the reaction required a large amount of solvent (DMF) and relatively high CO 2 pressure (3 MPa) (Scheme 50). Subsequently, mild N-heterocyclic olefins-CO 2 adducts (NHO-CO 2 )/MTBD organic catalytic system was reported by Zhou and Lu et al. [49]. In the presence of this system, various functionalized five-membered cyclic carbonates could be obtained under ambient conditions (Scheme 51a). Notably, this system showed high tolerance for a wide range of vicinal diols. The corresponding cyclic carbonates could be produced in moderate to high yields. Specifically, this three-component reaction proceeded via a one-pot two steps strategy. The initial carboxylative cyclization was catalyzed by the NHO-CO 2 adducts under ambient conditions. Once propargylic alcohols were completely converted, MTBD, vicinal diols and solvents were added successively for the subsequent transesterification. Additionally, the authors employed complicated polyhydroxy carbohydrate derivatives for this one-pot method to accurately synthesize bio-based cyclic carbonates. Regarding organocatalysis, strong bases such as DBU, TBD, and MTBD, etc., are beneficial for the activation of CO2 and hydroxyl groups due to their rich electronegativity [52]. Based on this, Song and Liu et al. [52] reported a facile metal-free DBU-catalyzed strategy for the one-pot preparation of cyclic carbonates and α-hydroxy ketones from propargylic alcohols, CO2 and vicinal diols. However, the reaction required a large amount of solvent (DMF) and relatively high CO2 pressure (3 MPa) (Scheme 50). Subsequently, mild N-heterocyclic olefins-CO2 adducts (NHO-CO2)/MTBD organic catalytic system was reported by Zhou and Lu et al. [49]. In the presence of this system, various functionalized five-membered cyclic carbonates could be obtained under ambient conditions (Scheme 51a). Notably, this system showed high tolerance for a wide range of vicinal diols. The corresponding cyclic carbonates could be produced in moderate to high yields. Specifically, this three-component reaction proceeded via a one-pot two steps strategy. The initial carboxylative cyclization was catalyzed by the NHO-CO2 adducts under ambient conditions. Once propargylic alcohols were completely converted, MTBD, vicinal diols and solvents were added successively for the subsequent transesterification. Additionally, the authors employed complicated polyhydroxy carbohydrate derivatives for this one-pot method to accurately synthesize bio-based cyclic carbonates. similar Ag2O/1,1,3,3-tetramethylguanidine (TMG) system for this three-component reaction, which could proceed successfully under 1 MPa of CO2 in CH3CN with a TON up to 1260 (Scheme 53) [54]. In addition to the Ag(I) catalytic systems, more economical Cu(I) catalytic systems were developed for this three-component reaction by the same group in 2018. The desired products could be obtained in good to excellent yield in the presence of CuI, 1,10-phen, and t-BuOK under 0.5 MPa of CO2 (Scheme 54) [55]. Although significant progress has been achieved, these catalytic systems still suffered from several shortcomings such as the requirement for high CO2 pressure, the addition of solvents or additives, low catalyst recyclability, and high metal loading, which limited their further applications in industry.
Inspired by these works, our group combined the advantages of transition-metal catalysts and ILs and developed a favorable AgNO3/ [C2C1im][OAc] system for this reaction (Scheme 55a) [57]. A wide range of 2-oxazolidinones and α-hydroxyl ketones could be simultaneously obtained in excellent yields under atmospheric CO2 pressure at 60 °C without any additives or traditional volatile solvents with an extremely low metal loading (0.25% AgNO3). In addition, this system showed excellent recyclability, which could be easily recycled and reused 5 times. Moreover, this system exhibited outstanding performance in evaluating the green metrics. In the aspect of the catalytic mechanism, the basic OAc − firstly activated the −OH in substrates 2, promoting its interaction with CO2 to form Scheme 54. CuI, 1,10-phen and t-BuOK catalyzed three-component reaction of propargylic alcohols, CO 2 , and 2-aminoethanols.
Inspired by these works, our group combined the advantages of transition-metal catalysts and ILs and developed a favorable AgNO 3 /[C 2 C 1 im][OAc] system for this reaction (Scheme 55a) [57]. A wide range of 2-oxazolidinones and α-hydroxyl ketones could be simultaneously obtained in excellent yields under atmospheric CO 2 pressure at 60 • C without any additives or traditional volatile solvents with an extremely low metal loading (0.25% AgNO 3 ). In addition, this system showed excellent recyclability, which could be easily recycled and reused 5 times. Moreover, this system exhibited outstanding performance in evaluating the green metrics. In the aspect of the catalytic mechanism, the basic OAc − firstly activated the −OH in substrates 2, promoting its interaction with CO 2 to form the carbonate intermediates II. Next, the Ag species activated the C≡C bonds, resulting in the combination of the negatively charged oxygen atoms with the carbon atoms in the triple bonds to afford the five-membered rings III. Subsequently, the catalysts were released from the five-membered rings and intermediates IV were generated. Afterwards, intermediates V were produced through the nucleophilic attack of the carbonyl groups in intermediates IV by the nitrogen atoms of the substrates 2. Then the keto-enol tautomerism occurred, leading to the formation of intermediates VI. Finally, the desired 2-oxazolidinones 3 were generated via the intramolecular nucleophilic cyclization of intermediates VI with α-hydroxyl ketones 4 released from the molecules (Scheme 55b). Later, we demonstrated that the cheaper Cu(I) salt could also be employed as an effective catalyst for this reaction when combined with ILs (Scheme 56) [58]. In the presence of CuBr and 1-butyl-3-methylimidazolium acetate ([C 4 C 1 im][OAc]), a variety of desired products could be produced in good to excellent yields under 1 atm of CO 2 pressure with a low metal loading (0.5 mol% of CuBr). This system also did not require additional volatile organic solvents and additives. Moreover, it could be reused at least 3 times.
VI with α-hydroxyl ketones 4 released from the molecules (Scheme 55b). Later, we demonstrated that the cheaper Cu(I) salt could also be employed as an effective catalyst for this reaction when combined with ILs (Scheme 56) [58]. In the presence of CuBr and 1butyl-3-methylimidazolium acetate ([C4C1im][OAc]), a variety of desired products could be produced in good to excellent yields under 1 atm of CO2 pressure with a low metal loading (0.5 mol% of CuBr). This system also did not require additional volatile organic solvents and additives. Moreover, it could be reused at least 3 times. ) through an anion-exchange resin, for the green synthesis of 2-oxazolidinones and α-hydroxyl ketones based on the three-component reaction of propargylic alcohols, CO 2 and 2-aminoethanols under atmospheric CO 2 pressure at 80 • C (Scheme 57). These ILs act as both catalysts and solvents, which could be easily recycled and reused at least for 5 times without significant loss of activity.
In 2018, Li and He et al. [56] synthesized a task-specific IL, 1,5,7triazabicylo[4.4.0]dec-5-ene trifluoroethanol ([TBDH][TFE]) through an anion-exchange resin, for the green synthesis of 2-oxazolidinones and α-hydroxyl ketones based on the three-component reaction of propargylic alcohols, CO2 and 2-aminoethanols under atmospheric CO2 pressure at 80 °C (Scheme 57). These ILs act as both catalysts and solvents, which could be easily recycled and reused at least for 5 times without significant loss of activity.

Isomerization of α-Alkylidene Cyclic Carbonates
Recently, the isomerization of α-alkylidene cyclic carbonates generated from the carboxylative cycloaddition of CO2 into propargylic alcohols was developed to afford valuable tetronic acids, which are a series of crucial intermediates and essential skeletons in agricultural, pharmaceutical, and biological chemistry [131][132][133]. Compared with the already reported route [59,[134][135][136][137][138][139], this route showed the advantages of easily accessible raw materials, mild reaction conditions, simple operation, high atom economy, etc. Consequently, it is an environmentally friendly alternative strategy, which provides a new methodology for the subsequent derivative applications of α-alkylidene cyclic carbonates.
AnUntil now, the only example for synthesizing tetronic acids through the reactions of propargylic alcohols and CO2 was reported in 2018. Zhou and Yu et al. [59] demonstrated that a wide range of tetronic acid derivatives could be obtained in 58-90% yields through the tandem reactions of cyclization and isomerization in the presence of excessive Cs2CO3 at atmospheric CO2 pressure and 65 °C in 1,3-dimethyl-2-imidazolidinone (DMI) (Scheme 58a). This system showed excellent tolerance for functional groups. The substrates with both symmetric and asymmetric dialkyl, methyl, and phenyl at α-position of the hydroxyl group, and cyclic, tertiary alcohols with various halogen substituents could undergo this process smoothly and obtain the target products with satisfactory yields. Based on the yield data, the aryl propargylic alcohols with electron-withdrawing groups were more favorable than those with electron-donating groups. The proposed mechanism for this reaction is shown in Scheme 58b. First, the CO2 reacts with the proton-removed substrates 1 to form carbonate intermediates I. Then the α-alkylidene cyclic carbonate intermediates II are formed through the intramolecular cyclization of intermediates I. Afterwards, the carbonate anions attacked the carbonyl groups in intermediates II and

Isomerization of α-Alkylidene Cyclic Carbonates
Recently, the isomerization of α-alkylidene cyclic carbonates generated from the carboxylative cycloaddition of CO 2 into propargylic alcohols was developed to afford valuable tetronic acids, which are a series of crucial intermediates and essential skeletons in agricultural, pharmaceutical, and biological chemistry [131][132][133]. Compared with the already reported route [59,[134][135][136][137][138][139], this route showed the advantages of easily accessible raw materials, mild reaction conditions, simple operation, high atom economy, etc. Consequently, it is an environmentally friendly alternative strategy, which provides a new methodology for the subsequent derivative applications of α-alkylidene cyclic carbonates.
AnUntil now, the only example for synthesizing tetronic acids through the reactions of propargylic alcohols and CO 2 was reported in 2018. Zhou and Yu et al. [59] demonstrated that a wide range of tetronic acid derivatives could be obtained in 58-90% yields through the tandem reactions of cyclization and isomerization in the presence of excessive Cs 2 CO 3 at atmospheric CO 2 pressure and 65 • C in 1,3-dimethyl-2-imidazolidinone (DMI) (Scheme 58a). This system showed excellent tolerance for functional groups. The substrates with both symmetric and asymmetric dialkyl, methyl, and phenyl at α-position of the hydroxyl group, and cyclic, tertiary alcohols with various halogen substituents could undergo this process smoothly and obtain the target products with satisfactory yields. Based on the yield data, the aryl propargylic alcohols with electron-withdrawing groups were more favorable than those with electron-donating groups. The proposed mechanism for this reaction is shown in Scheme 58b. First, the CO 2 reacts with the proton-removed substrates 1 to form carbonate intermediates I. Then the α-alkylidene cyclic carbonate intermediates II are formed through the intramolecular cyclization of intermediates I. Afterwards, the carbonate anions attacked the carbonyl groups in intermediates II and opened the rings to form intermediates III. Next, the carbonate anions were released via Dieckmann-type condensation and the intermediates IV were formed. Finally, the intermediates IV underwent further deprotonation by addition of excess Cs 2 CO 3 , resulting in the formation of enolates V, which could be quenched by the acids to produce the desired tetronic acids 2.
opened the rings to form intermediates III. Next, the carbonate anions were released via Dieckmann-type condensation and the intermediates IV were formed. Finally, the intermediates IV underwent further deprotonation by addition of excess Cs2CO3, resulting in the formation of enolates V, which could be quenched by the acids to produce the desired tetronic acids 2. Scheme 58. (a) Cs2CO3-catalyzed reaction of propargylic alcohols with CO2. (b) The proposed catalytic mechanism of Cs2CO3.

Conclusions
In summary, the tandem reactions based on the cyclization of CO2 and propargylic alcohols were summarized in this review. Notably, the three-component tandem reaction of CO2, propargylic alcohols with nucleophiles and the isomerization of α-alkylidene cyclic carbonates could afford a series of vital skeletons in organic synthesis, biology, and pharmacy. Moreover, these tandem routes exhibited great economic and environmental benefits. Currently, catalytic systems have been increasingly developed for these reactions, aiming to remove volatile organic solvents, and improve catalytic activity and recyclability. However, the reported reaction systems still have some drawbacks such as dependence on high catalyst equivalent and high purity of CO2, which limits their largescale industrial application. Therefore, the development of catalysts with low catalyst loading to reduce costs and a higher CO2 adsorption to utilize low-concentration CO2 are urgently required. These achievements will expand this area into a more important branch of the future CCU strategy.

Conclusions
In summary, the tandem reactions based on the cyclization of CO 2 and propargylic alcohols were summarized in this review. Notably, the three-component tandem reaction of CO 2 , propargylic alcohols with nucleophiles and the isomerization of α-alkylidene cyclic carbonates could afford a series of vital skeletons in organic synthesis, biology, and pharmacy. Moreover, these tandem routes exhibited great economic and environmental benefits. Currently, catalytic systems have been increasingly developed for these reactions, aiming to remove volatile organic solvents, and improve catalytic activity and recyclability. However, the reported reaction systems still have some drawbacks such as dependence on high catalyst equivalent and high purity of CO 2 , which limits their large-scale industrial application. Therefore, the development of catalysts with low catalyst loading to reduce costs and a higher CO 2 adsorption to utilize low-concentration CO 2 are urgently required. These achievements will expand this area into a more important branch of the future CCU strategy.  Data Availability Statement: All data were taken from the articles of the bibliography section.

Conflicts of Interest:
The authors declare no conflict of interest.