Synthesis of Graphene-Based Biopolymer TiO 2 Electrodes Using Pyrolytic Direct Deposition Method and its Catalytic Performance

: The traditional methods used to synthesize graphene layers over semiconductors are chemical-based methods. In the present investigation, a novel photoelectroactive electrode was synthesized using a chitosan biopolymer without the usage of chemicals. A chitosan-biopolymer layer over the surface of TiO 2 was generated by electrodeposition. Furthermore, the pyrolysis method was used for the conversion of a biopolymer into graphene layers. The catalytic activity of the fabricated electrodes was investigated by the photo-electro-Fenton (PEF) process to oxidize chloramphenicol and nadolol pharmaceutical drugs in wastewater, remove metals (scandium, neodymium, and arsenic) and degrade real municipal wastewater. The PEF operational parameters (pH, voltage, reaction time, and Fenton catalytic dose) were optimized for the overall degradation of chloramphenicol and nadolol pharmaceutical drugs in wastewater. It was observed that at the optimum process operational parameters it took 40 min to degrade chloramphenicol and nadolol pharmaceutical drugs in wastewater. It was proved that biopolymer-based photoelectroactive novel electrodes render good catalytic activity. Furthermore, the reusability study of fabricated electrodes showed excellent storage and self-healing properties.


Introduction
The graphene structure has many superior properties for wastewater treatment studies by advanced oxidation processes [1]. Graphene has a zero bandgap between its valence and conduction bands and a strong ambipolar electric field effect at room temperature [2,3]. Moreover, graphene has attracted immense interest owing to its lightweight, unique planar structure, excellent mechanical strength, superior electron conductivity (10 7 -10 8 S/m) and mobility, high specific surface area (2630 m 2 /g), and good adsorption capacity [4]. Graphene is an excellent electrocatalyst with thermal and photochemical stability [5]. All these outstanding properties have thus aroused great research interest from the fundamental study of various applications of graphene. Some researchers used graphene as a photocatalyst [6,7], but most of the researchers focused on modified graphene [8,9]. Numerous methods have been employed for the synthesis of graphene, such as the mechanical exfoliation method, thermal decomposition, chemical vapor deposition, the exfoliation and reduction of chemically oxidized graphite, etc. Among those methods, chemical oxidants have been widely used for the exfoliation of graphite into graphene oxide and then graphene [10]. To avoid the huge amount of chemical consumption, researchers have been producing green reducing agents (biopolymers) for graphene oxide and graphene composites. These composites have been used as catalysts for various processes. However, these composites have not been used as photo-electro-catalysts. So, researchers have been focused on the direct electrodeposition of graphene over the semiconductor, but to adhere to the surface of the semiconductor graphene needs to be partially reduced to graphene oxide. It has been substantially used for sensors, photovoltaic cells, supercapacitor lithium-ion batteries, and, more recently, electro-photocatalysis. Furthermore, it has been investigated that the electrochemically reduced graphene oxide after electrodeposition forms a huge number of oxygen-carrying groups, promoting the development of graphene-based materials [11,12]. However, the major drawback of the partial reduction of the graphene oxide approach over the semiconductors is that it generates hydrogen bubbles during the electrochemical reduction process and these hydrogen bubbles ultimately destroy the π-conjugation stack of graphene and reduce its conductivity. This drawback affects the successive applications of the electrodeposited film [13,14]. To overcome these issues, many approaches have been developed to enhance electrochemical performance without the reduction of graphene. Nevertheless, graphene is a highly conductive material with a conductance of 600,000 S/m and the fabrication of a highly active photo-catalyst on conductive or semiconductive base metal is desirable, with an ordered geometry and without using any binders [15].
Recently, there has been interest in the use of green materials such as biopolymers as an alternative to reduced graphene layers or synthesis of the graphene layer without any binder. These green materials yield high-quality single-layer and few-layer graphene sheets and massive production of graphene for the practical application over the semiconductor by electrodeposition. The biopolymer method approach has been successfully used for the development of photocatalytic material [16], to be readily applicable in photo-electroFenton. Among other biopolymers, chitosan has been extensively suitable for electrodeposition [17,18]. It has been illustrated that chitosan can be electrodeposited as a stable thin film on the cathode, by a successfully generated cathodic neutralization mechanism. Researchers have used this technique for biomedical purposes due to the component properties of electrogenerated chitosan thin films [19,20]. Moreover, the electrodeposition process permits a chitosan film to be deposited directly onto the surface of the metal [21,22]. In the present study, novel TiO 2 -G film electrodes have been synthesized using a chitosan biopolymer for the generation of graphene layers over the surface of the TiO 2 cylindrical tube (semiconductor) without using any binder. A nano-oxide layer has been synthesized over the semiconductor and acts as a binder between the semiconductor and the graphene layer. Chitosan is a cheap biomaterial from natural resources without chemical modification or binders, it has been used for the synthesis of the graphene layer. The pyrolysis conversion method has been used to convert the chitosan layer into the graphene layer and it shows good adhesive properties over the surface of TiO 2 . The catalytic activity of the synthesized TiO 2 -G film electrodes has been investigated through its treatment of synthetic pharmaceutical wastewater (chloramphenicol and nadolol), the removal of metals (scandium, neodymium, and arsenic), and the degradation of real municipal wastewater by the photo-electro-Fenton (PEF) process. The PEF process experiments have been statistically designed by response surface methodology. The degradation mechanism in terms of oxidation radicals during the PEF treatment process has been investigated. Furthermore, the reusability of fabricated electrodes has been examined to assess the stability and adhesive properties of the graphene layer over the surface of TiO 2 after the PEF treatment process.

Characteristics of TiO 2 -G Electrode
The TiO 2 -G electrode characterization was performed with an emission scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS) to examine the microstructure of the electrode. The graphene layer was scratched from the surface of the electrode to confirm the deposition. Its surface morphology was studied with SEM-EDS. Figure 1a shows a large graphene flake scratched from the surface of TiO 2 and it looked like a membrane or a layer. Moreover, Figure 1b shows the adhered uniform layer of graphene over the surface of TiO 2 . The corresponding EDS spectrum of TiO 2 -G exhibited the existence of carbon (16.04%wt), oxygen (10.71%wt), and titanium (73.25%wt). EDS mapping evidenced the presence of graphene over the TiO 2 surface ( Figure S1). The X-ray diffraction (XRD) spectroscopy pattern of the synthesized TiO 2 -G film was shown in Figure 2a. The formation of the TiO 2 rutile phase was confirmed, with the presence of two signature peaks of the TiO 2 rutile phase (JCPDS No. ) that appeared at 36.1 and 42.02 • indexed to (101) and (110) plane, respectively [22,23]. Contrarily, the XRD pattern of the TiO 2 -G film exhibited diffraction peaks at 60.8 and 72.8 • , which were attributed to the adherence of graphene film over the surface of TiO 2 . Additionally, diffraction peaks at 39.9, 52.3, and 76.8 • , corresponding to the characteristic peaks of titanium [24], represented the titanium (Ti) base metal. The presence of the graphene was further supported by Raman spectroscopy. Figure 2b shows the Raman spectra for the electrode TiO 2 -G. The representative D and G peaks expected of the graphene layer were identified at 1351 and 1596 cm −1 , respectively, over the TiO 2 surface. To confirm the presence of graphene, pristine graphene was used as a reference. The intensity ratio (I D /I G ) of the D and G band confirmed the presence of graphene over the TiO 2 surface. Furthermore, the existence of characteristic bands at A1g (607 cm −1 ) and Eg (400 cm −1 ) of TiO 2 in the lower wavenumber range showed the presence of the TiO 2 rutile phase [25].
Catalysts 2020, 10, x FOR PEER REVIEW 3 of 16 The TiO2-G electrode characterization was performed with an emission scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS) to examine the microstructure of the electrode. The graphene layer was scratched from the surface of the electrode to confirm the deposition. Its surface morphology was studied with SEM-EDS. Figure 1a shows a large graphene flake scratched from the surface of TiO2 and it looked like a membrane or a layer. Moreover, Figure 1b shows the adhered uniform layer of graphene over the surface of TiO2. The corresponding EDS spectrum of TiO2-G exhibited the existence of carbon (16.04%wt), oxygen (10.71%wt), and titanium (73.25%wt). EDS mapping evidenced the presence of graphene over the TiO2 surface ( Figure S1). The X-ray diffraction (XRD) spectroscopy pattern of the synthesized TiO2-G film was shown in Figure 2a. The formation of the TiO2 rutile phase was confirmed, with the presence of two signature peaks of the TiO2 rutile phase (JCPDS No. ) that appeared at 36.1 and 42.02° indexed to (101) and (110) plane, respectively [22,23]. Contrarily, the XRD pattern of the TiO2-G film exhibited diffraction peaks at 60.8 and 72.8°, which were attributed to the adherence of graphene film over the surface of TiO2. Additionally, diffraction peaks at 39.9, 52.3, and 76.8°, corresponding to the characteristic peaks of titanium [24], represented the titanium (Ti) base metal. The presence of the graphene was further supported by Raman spectroscopy. Figure 2b shows the Raman spectra for the electrode TiO2-G. The representative D and G peaks expected of the graphene layer were identified at 1351 and 1596 cm −1 , respectively, over the TiO2 surface. To confirm the presence of graphene, pristine graphene was used as a reference. The intensity ratio (ID/IG) of the D and G band confirmed the presence of graphene over the TiO2 surface. Furthermore, the existence of characteristic bands at A1g (607 cm −1 ) and Eg (400 cm −1 ) of TiO2 in the lower wavenumber range showed the presence of the TiO2 rutile phase [25].

Photo-Electrocatalytic Activity (PEA)
The PEA of TiO 2 -G film electrodes was estimated by the oxidative degradation of chloramphenicol and nadolol simulated wastewater, the removal of metals, and municipal wastewater degradation by PEF. Design-expert software (version: 11) was employed to optimize the experimental runs for the determination of the PEA of the fabricated electrodes. Response surface methodology (RSM) is a fact-based approach for precising the experimental runs and evaluating the impacts of independent process parameters on the chosen responses. Central composite design (CCD) using a second-order polynomial equation was used for the optimization of the operational parameters of the PEF process using TiO 2 -G film electrodes concerning the overall degradation of drugs [26]. To design the experimental runs, the selected PEF process independent variables were pH (X 1 ), voltage (X 2 ), Fe dose (X 3 ), reaction time (X 4 ), and response in terms of catalytic activity was taken as overall degradation of drugs (%D) in the simulated wastewater. Preliminary PEF experiments were performed to determine the high and low values of the operational parameters. All the variables were coded and demonstrated as low-level (−2, −1), medium level (0), and high-level (+1, +2) as shown in Table 1. RSM for the experimental design such as CCD fitted the model under least square error. When several operational parameters are involved in the optimization process then RSM is an effective tool for optimization with a minimal number of experiments. The adequacy of the model was diagnostically checked by the analysis of variance (ANOVA) [27]. The interaction of operational parameters would be easily employed by response surface plots. The most important parameters were selected for the PEF process from literature and preliminary experiments [28]. Experiments recommended by CCD (Table 2) were carried out to determine the catalytic activity of synthesized electrodes. A quadratic model was best fitted for RSM modeling of the PEF process. The adequacy of the quadratic model was assessed by utilizing a sequential F-test, model summary, and subsequent ANOVA. The adequate precision values for %D (overall degradation) were 19.01 respectively. An adequate precision ratio greater than 4 was desirable and indicated that the design space would be navigated by Catalysts 2020, 10, 1050 5 of 17 the RSM model. It also provided information about the efficacy of the suggested model to understand the relationship between independent variables and the responses. The model F-values indicated the significance of the model and P < 0.05 indicated the significant PEF model-independent parameters as shown in Table 3. The significant model parameters with respect to %D were pH, time (t), voltage (V), Fe dose (Fe), (pHxFe), (txV), pH 2 , V 2 , Fe 2 . The Lack of Fit F-values were not significant relative to the pure error function so, it was good for accurate model fitting. The significance of the quadratic model was observed with a 95% confidence level. The variations between the actual and predicted were very small (<1.5%). The values of the coefficient of the determinant (R 2 , adjusted R 2, and predicted R 2 ) were 0.96, 0.93, and 0.82, respectively. The predicted R 2 of 0.82 was in reasonable agreement with the adjusted R 2 of 0.93, i.e., the difference was less than 0.2. So, there was a good correlation between predicted and experimental data. Furthermore, the residual plot confirmed the validation of the quadratic model ( Figure S2). In terms of significant process parameters, Equation (1) supported the best fitting of the quadratic model. The relative impact of the process parameters was identified from the coded equation as shown below.

Effect of Operational Parameters
ANOVA analysis provided information regarding the significance of operational parameters on the overall degradation-based p-values during PEF treatment. A P-value less than 0.05 specified that the model terms were significant, i.e., process parameters showed a remarkable impact on the variability of the response. Parametric analysis was studied by 3D response surface graphs. It provided information about the effect of interactive parameters on the catalytic activity of PEF process. The correlative impact (95% of confidence interval) of the parameters, voltage, time, pH and Fe dose on the %D are illustrated in Figure 3a-c. It could be perceived that at the upper side of pH range (7-11), %D was found always decreasing with the increase in t-value. A sharp increase in %D was observed with an increase in pH value from 3 to 7 with a rise in t-value from 30 to 75 min. However, pH 5, at t = 50 min, showed a maximum %D (Figure 3a). The pH value plays an important role in the PEF process: when the pH of the photoelectron chemical cell was varied from 2.0 to 5.5, a sharp increase was observed in %D. However, with a further increase in pH (>5.5), there was a sharp decline in %D. It might have been because of the nature of the degrading compound (chloramphenicol and nadolol) or if it contained an amide group (pub-chem, molecule structure). So, it exhibited alkaline characteristics when dissolved in water, and to degrade it, acidic conditions were more favorable. On the other hand, when there was an increase in pH, the redox potential of chloramphenicol and nadolol decreased. Therefore, a major part of the photogenerated electrons were directly absorbed by chloramphenicol and nadolol, which ultimately lowered the thermodynamic driving force and oxidative ability of photoanode [28]. The valence band potential of photoanodes was affected by higher pH, and it shifted towards more negative potential. It reduced the electron (e-)/hole (h+) separation effect, which ultimately disturbed the oxidizing power (Jia et al., 2020) and affected the catalytic performance. Therefore, optimal pH was a necessity for PEF, but for most of the cases highly acidic conditions were favorable for PEF. Highly acidic pH (<4) was very difficult to maintain and aftertreatment disposal of highly acidic treated wastewater would be very problematic. So, goethite and hematite were used for Fe dose because they worked under a wide range of pH (=7). Goethite and hematite acted as a Fenton catalyst to proceed the Fenton reaction in a less acidic medium [29]. The increase and decrease of Fe dose and the pH of the photo-electrocatalytic chamber worked differently over the %D as shown in Figure 3b. An increased Fe dose (0.1-0.4 mM) increased the %D at all pH values but when the Fe dose was >0.4 mM, there was a sharp decrease in %D at all pH values. It was observed that oxidation of pollutants by electrochemically generated H 2 O 2 occurred mainly on the surface of goethite and hematite photocatalysts rather than in bulk [29]. It enhanced the photocatalytic performance of catalysts by conducting an electron scavenging oxidation reaction. In general, the charge carriers (e-and h+) were generated upon light illumination (Equations (2)-(6) [30].
Catalysts 2020, 10, x FOR PEER REVIEW 7 of 16  It implies that the degradation process was very fast, which indicated that OH • mediated oxidation was prominent in the PEF process. Due to UVC illumination and applied voltage, OH • radicals were generated via Equations (7)-(10).   Figure 3c demonstrates that the %D increased with an increase in voltage up to 3.8 V concerning t-value. However, %D was sharply affected when the voltage increased from 3.8 V with the increase in t-value. At the t-value of 60 min, %D was highest with the increase in voltage.
It implies that the degradation process was very fast, which indicated that OH . mediated oxidation was prominent in the PEF process. Due to UV C illumination and applied voltage, OH . radicals were generated via Equations (7)- (10).
It was evidenced that the voltage was a highly significant parameter in the PEF process. Fe dose > 0.4 mM at voltage > 3.8 V, negatively impacted the photo-electroFenton reaction because other weaker reactive oxygen species such as H 2 O 2 and hydroperoxyl radical (HO . 2 ) come into existence via reactions (11) and (12).
With an increase in voltage at a higher Fe dose, the photo-electrochemical electrolyte would increase the weaker reactive oxygen species and ultimately reduce the %D. There was a direct relation between the applied voltage to the band bending of the semiconductor, it improved the charge separation and transfer of charge carriers between the graphene and TiO 2 [31]. When the applied voltage became greater than the flat band potential (3.8 V) of TiO 2 -G film, it negatively affected the %D. Voltage of 3.8 V was enough for complete band bending and more efficient separation of the photogenerated electrons and holes [32]. Remarkably, optimized voltage (high bias potential) was important for avoiding side reactions during the PEF process. However, when the applied potential of the electrode increased from flat band potential, it ultimately decreased the %D because of the generation of repulsive forces between the charge carriers due to high voltage. The voltage-triggered electrons in the TiO 2 conduction band (Equation (13)) would react with the oxygen-generated · O 2 − radicals (Equation (14)).

Optimization
The optimization of PEF independent parameters with the response (%D) for the degradation of chloramphenicol-and nadolol-simulated pharmaceutical wastewater by the PEF process using TiO 2 -G film electrodes, with desirability function was executed. To optimize the values of the operating parameters, the target was set to maximize %D removal, while keeping electric energy consumption as a minimum. As a result, the optimum condition was found by the desirability function approach using R as pH = 5, voltage = 3.8 V, time = 45 min and Fe dose = 0.40 mM with a predicted response of %D = 86.02%. A set of three experiments was conducted with the optimized conditions. Average experimental %D values at optimal conditions came out to be 85.86%, which was in good compliance with the predicted value.

Degradation Mechanism
To investigate the feasible PEF mechanism of chloramphenicol and nadolol degradation, a free-radical quenching study was performed to determine the effect of active radicals by using different scavengers, i.e., 1,4-benzoquinone, ethylenediaminetetraacetic acid and tert-butyl alcohol Catalysts 2020, 10, 1050 9 of 17 were used as the scavengers of superoxide radical ( · O 2 − ), hole (h + ) and hydroxyl radical (OH . ), respectively. Figure 4 shows the catalytic activity of TiO 2 -G film electrodes before and after adding 1,4-benzoquinone, ethylenediaminetetraacetic acid and tert-butyl alcohol. In the presence of scavengers, catalytic activity in terms of degradation was reduced from 85.86% to 22.5% within 45 min under the optimized operational conditions of PEF. The catalytic activity of TiO 2 becomes almost double with the graphene layer. It was proved that OH . radicals were responsible for the chloramphenicol and nadolol degradation, whereas holes and · O 2 − radicals acted equally in the degradation process as shown in Figure 4. The result of the quenching study was supported by electron paramagnetic resonance (EPR). The spin adducts observed by the EPR (DMPO) represent the presence of four distinctive peaks having an intensity proportion of 1:2:2:1 ( Figure 5). It ensured the generation of OH . in the PEF treatment process [33], while 2,2,6,6-tetramethylpiperidine 1-oxyl (TEMPO) showed a typical signal of three peaks with an intensity of 1:1:1. The signal intensity secured the presence of · O 2 − radicals as shown in Figure 5. The results revealed that TiO 2 -G film was excited by photons and electrical influence, which promoted the generation of OH . and · O 2 − species. The collaborative effect of graphene and TiO 2 intensified the catalytic activity. The heterojunction structure of the TiO 2 rutile phase promoted the segregation of e − /h + pairs and ultimately enhanced the catalytic activity. The e − in the conduction band of graphene reduced the interface barrier and migrated towards the conduction band of titanium oxide and became involved in the cathode circuit. These electrons were further captured by oxygen in the electrolyte solution and converted into · O 2 − . The holes in the valence band of TiO 2 directly attacked the organic matter. The electrons from TiO 2 transferred into the G film. Holes in the valence band of G film also participated in the direct degradation of organics but the electrons with the effect of applied voltage moved into the circuit and also participated in the water molecule splitting to generate · O 2 − and OH . radicals [34]. Furthermore, it was involved in the degradation of chloramphenicol and nadolol into small molecules, ultimately decreasing reaction time. Herein, the synergistic effect of graphene and TiO 2 significantly enhanced the e − /h + separation, which provided a higher catalytic activity.
Catalysts 2020, 10, x FOR PEER REVIEW 9 of 16 degradation of chloramphenicol and nadolol into small molecules, ultimately decreasing reaction time. Herein, the synergistic effect of graphene and TiO2 significantly enhanced the e − /h + separation, which provided a higher catalytic activity.

Removal of Rare Earth Metals and Arsenic from Simulated Wastewater
The photocatalytic activity of the synthesized electrodes was also investigated for metals by the removal of scandium, arsenic, and neodymium from simulated wastewater. Simulated wastewater was prepared by dissolving scandium (50 ppm), arsenic (50 ppm), and neodymium (50 ppm) in tap water. A batch experiment was performed with the optimized operational parameters and 84.23% of

Removal of Rare Earth Metals and Arsenic from Simulated Wastewater
The photocatalytic activity of the synthesized electrodes was also investigated for metals by the removal of scandium, arsenic, and neodymium from simulated wastewater. Simulated wastewater was prepared by dissolving scandium (50 ppm), arsenic (50 ppm), and neodymium (50 ppm) in tap water. A batch experiment was performed with the optimized operational parameters and 84.23% of arsenic removal, 81.12% of scandium removal, and 74.56% of neodymium removal was observed. In the case of arsenic removal at the anode, the oxidation of water molecules occurred, which ultimately oxidized the oxo-anions (As III) to form complex H 3 AsO 4 . At the cathode oxo-anions (As V) became reduced and formed complex HAsO 3 −2 and HAsO 3 − [35]. In the case of rare-earth metals, the accurate mechanism behind the removal is not yet clear. Rare earth metals form complexes with a Fenton catalyst and with reduction and oxidation of water molecules. Furthermore, the stripping with H 2 SO 4 helps to recover the high purity (99%) of rare earth metals [36,37].

Degradation of Municipal Wastewater
The photocatalytic activity of the synthesized electrodes was also investigated for real municipal wastewater. Real municipal wastewater was collected from the Mikkeli, Finland wastewater plant. The initial chemical oxygen demand of the wastewater was 745 mg/L, pH = 7.2, Total organic carbon = 56.6 mg/L. A batch experiment was performed using the process with the optimized parameters. Removal of COD (67.56%) and TOC (60.18%) was observed after 45 min of the reaction time. The real wastewater study shows that there are certain real wastewater parameters (Fe concentration = 13mg/L, phosphorus = 11mg/L, nickel = 6.5 mg/L) that reduce the activity of synthesized electrodes [38], which ultimately increase the reaction time. The accuracy of the optimized operational parameters of heterogenous photo-electrocatalysis was confirmed.

Electrode Durability and Reusability
It is crucial to evaluate the durability and reusability of the catalysts for practical applications of photo-electrocatalysis in the real water treatment process. From a practical point of view, the durability of the electrode is very important. The stability of the TiO 2 -G film was examined under optimized PEF process conditions. The anodic voltage was maintained at 3.8 V with an increase in the reaction time. The fresh electrode provided %D of 85.86% but after the 10 × 5 h of successive PEF reactions, the efficiency of the electrodes was reduced by 1.32%. After successive reactions, the reduction of the catalytic activity was observed due to (i) the structural change of the metal and biopolymer layer, (ii) perturbation of the electrons and holes during the reaction with organic compounds, and (iii) diffusion between the surface of the electrode and the bulk solution. After the long-term PEF experiments, the used TiO 2 -G film electrode was re-examined by XRD, RAMAN, and SEM. It was observed that the structural configuration of the electrodes (RAMAN) was not much affected (Figure 6a) but in Figure 6b, the XRD peak shift was observed after the treatment process. XRD peak shift can be caused by several factors. In the present conditions, applied voltage, hematite and goethite might be responsible for the XRD peak shift. It revealed a little consistent shifting for characteristic peaks to higher 2θ values because of the lattice parameters of the synthesized electrode undergoing material change with the effect of voltage and the Fenton catalyst in the electrolyte. This variation in lattice parameters would lead to the lattice strains, ultimately creating the internal stress and decreasing the length of lattice parameters, leading to increased molecular size which in turn depicted a peak shifting towards greater 2θ in XRD analysis [39,40]. An XRD peak corresponding to Ti showed higher intensity after treatment. It showed that the oxide layer was a little bit depleted after treatment. SEM images showed minute cracks in the GO film after successive PEF reactions as shown in Figure 7a. The TiO 2 -G film electrodes were stored in tap water for two days; then a PEF reaction was run for chloramphenicol and nadolol oxidation and excellent catalytic activity towards chloramphenicol and nadolol oxidation was observed (85.58%). In terms of conductivity, chitosan-modified membranes have excellent stability in water [41]. Further, SEM was performed again to understand the structural changes of TiO 2 -G film. This indicated that the TiO 2 -G film electrodes regained their catalytic activity in the presence of water as shown in Figure 7b. After 50 (5 h per day) h of PEF reactions, their catalytic activity was reduced and further regenerated after two days of storage in water. The chitosan membranes have self-healing properties [42,43]. The consistency of the graphene layer was damaged with a successive PEF reaction but the minute cracks were healed over the surface of the electrode. Its further use may provide reduced catalytic activity with time. So, further modification to the electrode synthesis is required to increase the adhesive properties of graphene over the surface of the semiconductor to achieve long durability. Overall, the present electrode synthesis method provides good restorable catalytic activity and storage properties of the catalytic electrode.
Catalysts 2020, 10, x FOR PEER REVIEW 11 of 16 graphene over the surface of the semiconductor to achieve long durability. Overall, the present electrode synthesis method provides good restorable catalytic activity and storage properties of the catalytic electrode.

Electrode Fabrication (TiO2-G Film)
A seamless Ti tube with 165 cm 2 area was used as a base material for electrode fabrication. Silicon carbide sandpaper was used to polish the roughness of the Ti tube and then it was cleaned with acetone, isopropanol and finally with distilled water. Mechanical etching of the Ti tube was performed ultrasonically with 1:10 (acetone and water) for 60 min. Chemical etching of the Ti tube was performed (HF: HNO3: H2O; 1:4:10) for 10 s and then rinsed with distilled water. Anodization

Electrode Fabrication (TiO 2 -G Film)
A seamless Ti tube with 165 cm 2 area was used as a base material for electrode fabrication. Silicon carbide sandpaper was used to polish the roughness of the Ti tube and then it was cleaned with acetone, isopropanol and finally with distilled water. Mechanical etching of the Ti tube was performed ultrasonically with 1:10 (acetone and water) for 60 min. Chemical etching of the Ti tube was performed (HF: HNO 3 : H 2 O; 1:4:10) for 10 s and then rinsed with distilled water. Anodization was performed with Ti seamless perforated tube (3 cm) as a positive electrode and copper tube (3 cm) as a negative electrode. The distance maintained between the electrodes was 1 cm in 5% HF electrolyte at 20 V (Minipa MPL-1303 power supply) for 2 h. The fresh anodized electrode was calcinated in the muffle furnace (500 • C) for 3 h. The electrodeposition of chitosan proceeded with the preparation of the chitosan solution. An aqueous solution of chitosan was prepared by dissolving 600 mg of chitosan in 800 mL of water and 1% (V/V) acetic acid. The prepared stock solution was stirred for 1 h. During the electrodeposition process, TiO 2 was used as a cathode and a parallel copper tube as an anode. Direct current was supplied for the electrodeposition (Model: Minipa MPL-1303) with a constant voltage of 20 V for 3 h. Furthermore, after the electrodeposition process, the electrodes were rinsed with distilled water and then dried at 50 • C in the air-dry oven overnight. The thin film was pyrolyzed under the Ar atmosphere at 900 • C. Characterization of the synthesized electrode was performed using an X-ray diffractometer (XRD, Empyrean series 2 PANalytical X-ray with Co-anode at 40 kW, 30 mA), Monochromator 3D, a high dynamic range pixel detector was purchased from Malvern Panalytical a spectris company, Malvern, United Kingdom. HORIBA Jobin Yvon LabRAM HR, RAMAN spectroscopy, HORIBA UK limited, Northampton, United Kingdom (a green laser with wavelength 514.53 nm) explored the chemical and molecular interaction. The surface material elemental and chemical composition of the synthesized electrode was explored by scanning electron microscopy (SEM)-energy dispersive X-ray spectroscopy (EDS) (Hitachi S-4800, Krefeld, Germany).
The synthesized electrode was cut into a 0.5 × 0.5 cm 2 piece. This electrode piece was directly used as a sample for characterization. In the case of SEM-EDS, the direct electrode (0.5 × 0.5 cm 2 piece) and a scratch from the surface of the TiO 2 base were used as samples for characterization. The accelerating voltage and emission current for SEM were 2.00 kV and 65.8 µA, respectively.

Design of Experiments, Experimental Setup and Procedure
The experiments were designed using the statistical design-expert software version 11 (STAT-EASE Inc., Minneapolis, MN, USA) program. Central composite design (CCD) based on response surface methodology (RSM) was used for the experimental design and analysis of the experimental data. It consisted of factorial runs (2 N ), axial runs (2 N ) and experimental error calculated by center runs (C E ). CCD was implemented for the quadratic effect because the second-order effect did not estimate separately by 2 N factorial design. In the statistical analysis, the desired response was optimized corresponding to the independent process parameters. The statistical parameters were calculated by ANOVA with the aid of RSM [37]. CCD under RSM statistically designed the experiments, furthermore, determined the mathematical model, and finally checked the accuracy of the mathematical model in terms of F-value. The selected PEF process independent variables were pH (X 1 ), voltage (X 2 ), Fe dose (X 3 ), reaction time (X 4 ), and response in terms of catalytic activity was taken as overall degradation of drugs in the simulated wastewater. The range and level of the factors varied accordingly to pre-performed experiments (Equation (15)).
where X was the response of the system andX 1 , X 2 , X 3, and X 4 were independent selected PEF process variables. A true correlation between the independent variables and responses was needed to identify the optimization of response variables concerning independent variables. CCD arranged the designed experimental run in standard order for data clustering to diminish the error and effect of the uncontrolled factors. An empirical model second-order polynomial equation was generated to correlate between the independent variables and response (Equation (16)).
where ∂ 0 is the constant coefficient, ∂ i , ∂ ii , ∂ ij were linear interaction coefficients, quadratic, and second-order terms, respectively. The terms x i and x j were variables and ∀ was an error function. The accuracy of the model was determined in terms of R 2 , adjusted R 2 , and predicted R 2 .
The statistical significance of the model was observed by an adequate precision ratio. A batch reactor was designed at a laboratory scale for the treatment of chloramphenicol-and nadolol-simulated pharmaceutical wastewater by PEF process with a working volume of 1 L and fused glass bubblers at the substratum of the reactor for injecting air. UV-C18 W lamps (Philips) were positioned at the top and the bottom of the reactor. For PEF designed experiments, the TiO 2 -G film electrodes as anode and cathode were placed inside the glass reactor (diameter of 3 cm) as shown in Figure 8. The voltage for an experimental condition was managed by using a direct current power supply (Minipa PL-1303). All the experiments were carried out in a laboratory with excellent air ventilation. The pH of each experimental run was adjusted according to requirements. After the termination of each run, the withdrawn samples were permitted to settle dispersed particles for 60 min. The upper liquid phase was taken for further analysis. electrodes as anode and cathode were placed inside the glass reactor (diameter of 3 cm) as shown in Figure 8. The voltage for an experimental condition was managed by using a direct current power supply (Minipa PL-1303). All the experiments were carried out in a laboratory with excellent air ventilation. The pH of each experimental run was adjusted according to requirements. After the termination of each run, the withdrawn samples were permitted to settle dispersed particles for 60 min. The upper liquid phase was taken for further analysis.

Analytical Methods
A MeterLab standard pH meter was used to measure the pH of the wastewater. A double beam UV−visible spectrophotometer (HACH, DR 5000, Colorado, USA) was used to analyze the degradation of simulated wastewater samples. The λmax of chloramphenicol is 272 nm and nadolol displays three absorption peaks in the ultraviolet region at about 218, 270, and 278 nm. Catalytic activity in terms of overall degradation (%D) was calculated by using Equation (17), where B1 = initial absorbance; B2 = final absorbance. Chloramphenicol sample absorbance was observed at 272 nm and nadolol absorbance was observed at three peaks, 218, 270, and 278 nm.
An inductively coupled plasma-optical emission spectroscopy (ICP-OES) Optima 8000 Series-Perkin Elmer Co., USA was used to determine the concentration of metals in the synthetic wastewater. The catalytic mechanism was explained by EPR (EPRA-9300/CMS 8400) to observe the generation of radicals during the PEF treatment process.

Conclusions
Graphene film TiO2 electrodes have been successfully synthesized with the pyrolysis method. It has been concluded that the nano-oxide layer acts as a good binder between the semiconductor and

Analytical Methods
A MeterLab standard pH meter was used to measure the pH of the wastewater. A double beam UV−visible spectrophotometer (HACH, DR 5000, Colorado, CO, USA) was used to analyze the degradation of simulated wastewater samples. The λmax of chloramphenicol is 272 nm and nadolol displays three absorption peaks in the ultraviolet region at about 218, 270, and 278 nm. Catalytic activity in terms of overall degradation (%D) was calculated by using Equation (17), where B 1 = initial absorbance; B 2 = final absorbance. Chloramphenicol sample absorbance was observed at 272 nm and nadolol absorbance was observed at three peaks, 218, 270, and 278 nm.
An inductively coupled plasma-optical emission spectroscopy (ICP-OES) Optima 8000 Series-Perkin Elmer Co., USA was used to determine the concentration of metals in the synthetic wastewater. The catalytic mechanism was explained by EPR (EPRA-9300/CMS 8400) to observe the generation of radicals during the PEF treatment process.

Conclusions
Graphene film TiO 2 electrodes have been successfully synthesized with the pyrolysis method. It has been concluded that the nano-oxide layer acts as a good binder between the semiconductor and the graphene layer. A nano-oxide layer increases the adhesive properties of graphene over the surface of the semiconductor. The catalytic activity of the TiO 2 -G film electrode was investigated by the PEF process to oxidize pharmaceutical drugs, remove metals, and treat municipal wastewater. It has been concluded that due to the high conductivity of graphene, the electrons in the conduction band of graphene reduce the interface barrier and migrate towards the conduction band of TiO 2 and get involved in the cathode circuit. It ultimately acts as a photocatalyst and an electrocatalyst for the degradation of pharmaceutical drugs. The catalytic activity of TiO 2 -G film is quite good for the treatment of municipal wastewater. So, TiO 2 -G film electrodes have good catalytic activities to be used for real applications. It has been proved that the catalytic activity of titanium oxide doubled with the synthesis of the graphene layer over it. The reusability study of the fabricated electrode showed its better durability, excellent storage, and self-healing properties but needed modification for long term use of TiO 2 -G film electrodes in practical applications. Nevertheless, the prepared TiO 2 -G film electrodes exhibited excellent degradation capacity, demonstrating a promising technology for the treatment of pharmaceuticals, metal removal, as well as real wastewater micropollutants.