Atom-economical Synthesis and Characterization of Poly(oxindolidene thienylene vinylene) Based on Aldol Polycondensation Reaction

: It is known that π -conjugated polymers can be easily synthesized using monomers which possess metals or halogen atoms as well as transition-metal catalysts. However, in the polymer materials synthesized by such reactions, small amounts of halogens and transition-metal-catalysts remain, often negatively a ﬀ ecting their optoelectronic device performances. Herein, we report a new polycondensation method based on the aldol condensation reaction utilizing the intramolecular resonance e ﬀ ect of the anionic monomer through π -conjugation. We have designed a novel AB type monomer to synthesize the semiconducting poly(oxindolidene thienylene vinylene) (POTV) using the proposed system. Indeed, the polymerization readily proceeded by adding 5-nitro-2-thiophenecarbaldehyde as an initiator after the α -proton abstraction of the oxindole group by the reaction of the monomer precursor with lithium hexamethylsilazide (LiHMDS) / 12-crown-4. As a result, the objective POTV with M n = 3700 and Ð M = 1.47 could be obtained with a good yield (65%). In addition, an organic ﬁeld e ﬀ ect transistor (OFET) was based on POTV exhibited p-type characteristics, with a hole mobility of 2.24 × 10 − 4 cm 2 V − 1 s − 1 .


Introduction
Organic electronics, such as organic photovoltaics (OPVs) and organic field effect transistors (OFETs), have been well studied in recent years, because they have several advantages, such as a high mechanical flexibility and solution processability [1,2]. Therefore, the development of π-conjugated polymers employed in such organic electronic devices has been actively conducted [3][4][5]. Moreover, π-conjugated polymers used for such devices can be easily synthesized by transition-metal-catalyzed cross-coupling polycondensations.
The cross-coupling reactions include, for example, the Mizoroki-Heck [6,7], Kumada-Tamao [8], Sonogashira [9], Negishi [10,11], Migita-Kosugi-Stille [12,13], and Suzuki-Miyaura [14,15] reactions, and they are well known as the most practical methods for the formation of aryl-aryl bonds over the past four decades. For the synthesis of semiconducting polymers applicable to organic electronics, the Migita-Kosugi-Stille cross-coupling polycondensation has often been employed. However, these synthetic methods usually have some issues. First, expensive organometallic reagents are required for the synthesis of functionalized monomers, followed by troublesome purification steps. Second, the stoichiometric quantities of organometallic by-products, Scheme 1. Expected mechanism for the preparation of poly(oxindolidene thienylene vinylene) by the aldol condensation reaction.

Polymerizations
According to the successful polymerization method based on the Horner-Wadsworth-Emmons reaction reported by Goto et al., we tried to suppress the unwanted step-growth propagation reaction by adding a variety of bases to OTV in THF at −78 °C. All the polymerizations were initiated with 5nitro-2-thiophenecarboxaldehyde and allowed to stand for 24 h, targeting an Mn value of 10,800. The results are summarized in Table 1.

Polymerizations
According to the successful polymerization method based on the Horner-Wadsworth-Emmons reaction reported by Goto et al., we tried to suppress the unwanted step-growth propagation reaction by adding a variety of bases to OTV in THF at −78 • C. All the polymerizations were initiated with 5-nitro-2-thiophenecarboxaldehyde and allowed to stand for 24 h, targeting an M n value of 10,800. The results are summarized in Table 1. First, 1.05 equivalents of sodium hexamethyldisilazide (NaHMDS) / 15-crown-5 as a base to OTV was used. The polymerization was then perfomed at −40 • C for 24 h (Run 1). The 15-crown-5 was expected to capture the sodium cation of NaHMDS, and increase the reactivity of the monomer anions. Unfortunately, the polymerization hardly proceeded (M n = 1300). Therefore, we attempted to accelerate the reactivity of the monomer anions by increasing the reaction temperature to room temperature without changing the other conditions (Run 2). As a result, the molecular weight was slightly improved (M n = 2100), probably due to the increased reactivity between the polymer chain end and incoming monomers at the elevated temperature from −40 • C to room temperature. Next, the solvent used for the polymerization was optimized. Actually, THF was changed to the mixed solvent of toluene / THF = 20.0 / 0.17 by vol. (Run 3) and a slight improvement was noted in the molecular weight (M n = 2600, Ð M = 1.46). This is considered to be due to the suppressed inactivation of the formyl group of the monomer based on the lower resonance effect in the more apolar solvent. Therefore, toluene / THF = 20.0 / 0.17 by vol. was adopted as the solvent, then the base was optimized. Lithium hexamethylsilazide (LiHMDS) was previously used in the successful synthesis of the well-defined polyamide [29]. Thus, LiHMDS was employed as a base for the α-proton abstraction. Under this condition, the molecular weight of the obtained POTV was not improved, showing a value similar to that for Run 3. On the other hand, the molecular weight distribution was slightly improved (Run 4, M n = 2500, Ð M = 1.37). The SEC curves for the resulting polymers are shown in Figure 1. They indicated that the monomer was mostly consumed under the conditions using LiHMDS (Runs 4-6). The result may be derived from the atomic radius size of the cation. The smaller the atomic radius of the cation, the closer the distance between the anionic monomers and counter cation. Therefore, the lithium cation with a small atomic radius was close to the monomer and reduced the effect of the resonance stabilization, to improve the reactivity of the formyl group of OTV. Since LiHMDS was determined to be an effective base, the amount of 12-crown-4 was optimized (Run 5). Reducing the amount of 12-crown-4 from 1.05 to 0.1 equivalent to OTV further improved the molecular weight (M n = 3000, Ð M = 1.45). It was postulated that the reduction of the crown ether amount enhanced the contact ion pair between the anionic monomer and Li cation, resulting in a lower resonance effect and futher increasing the reactivity of the formyl group of OTV. Finally, the reaction temperature was raised to 30 • C, to improve the reactivity of the monomer (Run 6). As a result, POTV with the highest M n value was obtained, although the Ð M value was not very low (M n = 3700, Ð M = 1.47). This improvement in molecular weight is again probably due to the enhanced reactivity between the polymer chain end and monomers at the elevated temperature. Eventually, POTV with M n = 5300, Ð M = 1.57 could be obtained by the Soxhlet extraction of POTV (Run 6) with methanol, hexane and acetone, followed by recovering with chloroform. It should be noted that there are several sharp peaks in the lower molecular weight region of the SEC curves for all Runs. They may possibly be derived from the linear and/or cyclic oligomers, which are hardly removed by the Soxhlet extraction. The presence of oligomers suggests the partial step-growth mechanism for the proposed polymerization, which are coincident with the fact that the resulting POTVs were obtained in relatively high yields, while having lower M n values than expected.

Optical Properties and Microstructures
The normalized UV-vis absorption spectra of POTV in both the solution and film states (Run 6) are shown in Figure 2. The optical characteristics are summarized in Table 2. POTV exhibited a multiband spectrum that is often observed for donor-acceptor (D-A) polymers. The high-energy region correscponds to the π-π* transition, while the low-energy region is attributed to the intra-and intermolecular charge transfer (ICT) band (0-1 and 0-0) between the D-A units. It is obvious that the λmax shifted to the longer wavelength region from the solution to film states. This is probably because of the enhanced ICT effect, caused from the more coplanar structures in the film state than in the solution, inducing the polymer intermolecular interactions. Based on the absorption onset, the optical band gaps of POTV were calculated to be 1.66 eV and 1.64 eV for the as-cast and annealed films, respectively. The results suggest that the annealing treatment improves the planarity of the molecules and futher enhances the intermolecular interaction in the solid state.

Optical Properties and Microstructures
The normalized UV-vis absorption spectra of POTV in both the solution and film states (Run 6) are shown in Figure 2. The optical characteristics are summarized in Table 2. POTV exhibited a multiband spectrum that is often observed for donor-acceptor (D-A) polymers. The high-energy region correscponds to the π-π* transition, while the low-energy region is attributed to the intra-and intermolecular charge transfer (ICT) band (0-1 and 0-0) between the D-A units. It is obvious that the λ max shifted to the longer wavelength region from the solution to film states. This is probably because of the enhanced ICT effect, caused from the more coplanar structures in the film state than in the solution, inducing the polymer intermolecular interactions. Based on the absorption onset, the optical band gaps of POTV were calculated to be 1.66 eV and 1.64 eV for the as-cast and annealed films, respectively. The results suggest that the annealing treatment improves the planarity of the molecules and futher enhances the intermolecular interaction in the solid state.

Optical Properties and Microstructures
The normalized UV-vis absorption spectra of POTV in both the solution and film states (Run 6) are shown in Figure 2. The optical characteristics are summarized in Table 2. POTV exhibited a multiband spectrum that is often observed for donor-acceptor (D-A) polymers. The high-energy region correscponds to the π-π* transition, while the low-energy region is attributed to the intra-and intermolecular charge transfer (ICT) band (0-1 and 0-0) between the D-A units. It is obvious that the λmax shifted to the longer wavelength region from the solution to film states. This is probably because of the enhanced ICT effect, caused from the more coplanar structures in the film state than in the solution, inducing the polymer intermolecular interactions. Based on the absorption onset, the optical band gaps of POTV were calculated to be 1.66 eV and 1.64 eV for the as-cast and annealed films, respectively. The results suggest that the annealing treatment improves the planarity of the molecules and futher enhances the intermolecular interaction in the solid state.  To provide further an insight into the crystalline structures and the morphology of the POTV thin films, the grazing-incidence wide-angle X-ray scattering (GIWAXS) was examined. The 2D-GIWAXS images and the corresponding diffractogram profiles of the polymer films (as-cast, and annealed at 200 • C) are shown in Figure 3. The as-cast film of POTV exhibited out-of-plane (100), (200), and (300) diffraction peaks along the q z axis. Additionally, the in-plane (010) reflection peak along the q y axis was clearly observed (Figure 3a,b). Such crystalline lattices can be assigned similarly to the representative semiconducting polymer of regioregular head-to-tail poly(3-hexylthiophene) [30]. These results indicated that the as-cast thin film of POTV favored the edge-on orientation on the substrate. On the other hand, the crystalline structures and orientation of the annealed film of POTV at 200 • C significantly changed, exhibiting an out-of-plane (010) diffraction peak along the q z axis, and the in-plane reflection peak became rather complicated, showing multispots derived from higher order crystal structures (Figure 3c,d). The π-π stacking distances of the POTV as-cast film and its annealed film were determined to be 3.98 Å and 3.59 Å, respectively, from the (010) diffraction peaks. The result indicates that the annealing treatment enhanced the intermolecular interaction to decrease the π-π stacking distance. Remember that, in the UV-vis spectroscopy, the λ max value of the as-cast film shifted to the longer wavelength region, implying the occurrence of a more effective ICT, which is coincident with the behavior of the π-π stacking distance observed by GIWAXS, as already mentioned.  1.64 To provide further an insight into the crystalline structures and the morphology of the POTV thin films, the grazing-incidence wide-angle X-ray scattering (GIWAXS) was examined. The 2D-GIWAXS images and the corresponding diffractogram profiles of the polymer films (as-cast, and annealed at 200 °C) are shown in Figure 3. The as-cast film of POTV exhibited out-of-plane (100), (200), and (300) diffraction peaks along the qz axis. Additionally, the in-plane (010) reflection peak along the qy axis was clearly observed (Figures 3a,b). Such crystalline lattices can be assigned similarly to the representative semiconducting polymer of regioregular head-to-tail poly(3-hexylthiophene) [30]. These results indicated that the as-cast thin film of POTV favored the edge-on orientation on the substrate. On the other hand, the crystalline structures and orientation of the annealed film of POTV at 200 °C significantly changed, exhibiting an out-of-plane (010) diffraction peak along the qz axis, and the in-plane reflection peak became rather complicated, showing multispots derived from higher order crystal structures (Figure 3c,d). The π-π stacking distances of the POTV as-cast film and its annealed film were determined to be 3.98 Å and 3.59 Å, respectively, from the (010) diffraction peaks. The result indicates that the annealing treatment enhanced the intermolecular interaction to decrease the π-π stacking distance. Remember that, in the UV-vis spectroscopy, the λmax value of the as-cast film shifted to the longer wavelength region, implying the occurrence of a more effective ICT, which is coincident with the behavior of the π-π stacking distance observed by GIWAXS, as already mentioned.

OFET Performances
The OFET devices with bottom-gate top-contact architectures were fabricated for elucidating the semiconducting characteristics of POTV (Run 6), after Soxhlet extraction. Hole mobilities were measured on devices prepared on PETS-passivated substrates. It is noted that the presence of hydroxyl groups on the bare SiO 2 surface may act as charge traps. Measurements were performed at nitrogen atmosphere in the solution-sheared film. Figure 4 depicted the exemplary transfer curves for the POTV OFET device. The POTV OFET exhibited a good hole-transporting behavior, with a maximum hole mobility of 2.24 × 10 −4 cm 2 V −1 s −1 , despite its relatively low molecular weight M n = 5300 ( Table 3). The I d of the device is of the ordered of 10 −11 A, when it is in the OFF state, and increase up to 10 −7 A when it is turned to the ON state, thus indicating an ON/OFF current ratio of 1.92 × 10 4 .

OFET Performances
The OFET devices with bottom-gate top-contact architectures were fabricated for elucidating the semiconducting characteristics of POTV (Run 6), after Soxhlet extraction. Hole mobilities were measured on devices prepared on PETS-passivated substrates. It is noted that the presence of hydroxyl groups on the bare SiO2 surface may act as charge traps. Measurements were performed at nitrogen atmosphere in the solution-sheared film. Figure 4 depicted the exemplary transfer curves for the POTV OFET device. The POTV OFET exhibited a good hole-transporting behavior, with a maximum hole mobility of 2.24 × 10 −4 cm 2 V −1 s −1 , despite its relatively low molecular weight Mn = 5,300 ( Table 3). The Id of the device is of the ordered of 10 −11 A, when it is in the OFF state, and increase up to 10 −7 A when it is turned to the ON state, thus indicating an ON/OFF current ratio of 1.92 × 10 4 .

Materials
Tetrahydrofuran (THF, 99.5%, stabilizer-free, Kanto Chemical Co., Inc., Tokyo, Japan) was purified by refluxing over sodium benzophenone under nitrogen for 2 h, followed by distillation just before use. Other reagents purchased from Sigma-Aldrich Japan K.K., Tokyo Chemical Industry Co., Ltd., Kanto Chemical Co., Inc. or FUJIFILM Wako Pure Chemical Industries, Ltd., were used as received. Furthermore, (2-phenylethyl)trichlorosilane (PETS) for the self-assembly monolayer (SAM) treatment was purchased from Gelest, Inc. (1) Triphenylphosphine (14.2 g, 54.2 mmol) was placed in a 200 mL two-necked flask purged with N 2 . After dissolving in dichloromethane (86.0 mL), the solution was cooled down to 0 • C before addition of Br 2 (2.78 mL, 54.2 mmol). Then, 2-Hexyl-1-decanol (15.0 mL, 51.6 mmol) was added dropwise over 30 min and the reaction was stirred at room temperature overnight. The reaction was quenched by adding a saturated aqueous solution of Na 2 SO 3 , then extracted with dichloromethane. After the organic phase was dried over anhydrous magnesium sulfate, the filtered solution was removed under the reduced pressure. The resulting residue was washed with hexane, and the precipitates were filtered. The filtrate was concentrated under the reduced pressure, yielding the title compound as a pale-yellow oil (12.3 g, 83%). 1 (2) A compound 1 (7.63 g, 25.0 mmol), 6-bromoisatin (5.00 g, 22.1 mmol) and anhydrous potassium carbonate (3.66 g, 26.5 mmol) were placed in a 200 mL two-necked flask purged with N 2 . After dissolving the mixture in N,N-dimethylformamide (140 mL), it was heated to 60 • C and allowed to stand for 20 h. After cooling down to room temperature, the reaction mixture was extracted with ethyl acetate and washed with water and brine. The organic phase was dried over anhydrous magnesium sulfate, filtered, rotary evaporated, and purified by silica gel chromatography, using hexane/ethyl acetate (9/1) as an eluent to afford the title compound as an orange solid (8.14 g, 82%). 1

6-Bromo-(N-2-hexyldecyl)oxindole (3)
A compound 2 (7.95 g, 17.7 mmol) was placed in a 100 mL two-necked flask purged with N 2 . After dissolving it in dimethyl sulfoxide (65.0 mL), hydrazine (5.50 mL, 177 mmol) was added. The mixture was heated to 140 • C and allowed to stand for 40 min. After cooling down to 0 • C, the reaction was quenched by adding a 6 M HCl aq. (2.5 mL). The quenched solution was extracted with ethyl a cetate and washed with water and brine. The organic phase was dried over anhydrous magnesium sulfate, filtered, rotary evaporated and purified by silica gel chromatography using hexane/ethyl a cetate (8.5/1.5) as an eluent to afford the title compound as a viscous yellow oil (6.16 g, 80%). 1 13

5-(Trimetyltin)thiophene-2-carbaldehyde (5)
A compound 4 (1.90 g, 8.00 mmol) and tetrakis(triphenylphosphine)palladium(0) (0.462 g, 0.40 mmol) were placed in a 100 mL two-necked flask purged with N 2 . After dissolving the mixture in toluene (40.0 mL), hexamethylditin (2.50 mL, 12.0 mmol) was added, and the mixture was heated to 85 • C and allowed to stand for 8 h. After cooling down to room temperature, the reaction mixture was filtered through celite. It was then extracted with hexane and washed with water and brine. The organic phase was dried over anhydrous magnesium sulfate, filtered, rotary evaporated and purified by sublimation, yielding the title compound as a white crystalline solid (1.22 g, 55%). 1  The compounds of 3 (1.81 g, 4.14 mmol) and 5 (1.14 g, 4.14 mmol), tris(dibenzylideneacetone)dipalladium(0) (0.190 g, 0.207 mmol) and tri(o-tolyl)phosphine (0.317 g, 1.04 mmol) were placed in a 100 mL two-necked flask purged with N 2 . After dissolving the mixture in toluene (40.0 mL), it was heated to 100 • C and allowed to stand for 2 h. After cooling down to room temperature, the reaction mixture was filtered through celite. It was then extracted with hexane and washed with water and brine. The organic phase was dried over anhydrous magnesium sulfate, filtered, rotary evaporated and purified by silica gel chromatography using hexane/ethyl acetate (7/3) as and eluent to afford OTV as an orange solid (1.22 g, 63%). 1

Synthesis of POTV
The representative experiment for Run 6 (see Scheme 2) is as follows: A 20 mL two-necked flask was first purged with N 2 and placed with dehydrated toluene (18 mL), 12-crown-4 ether (8.0 µL, 0.05 mmol) and lithium hexamethyldisilazide (1.3 M in THF, 0.40 mL, 0.52 mmol). After cooling down the flask to −78 • C, the OTV solution (232 mg, 0.495 mmol, 2 mL of toluene) was added to the reaction mixture and allowed to stir for 5 min. The initiator of 5-nitro-2-thiophenecarboxaldehyde (3.4 mg, 0.022 mmol, 0.5 mL of toluene) was added to the mixed solution to start the polymerization. The polymerization was perfomed with stirring at 30 • C for 24 h. To quench the polymerization, a 5 M HCl aq. solution (2 mL) was finally added. The aliquot of the resulted solution was sampled out and extracted with a mixture of chloroform and water. The obtained sample was analyzed by SEC before precipitation. To precpitate the polymer, the rest of the solution was poured into methanol/water (200 mL/ 100 mL). By filtrating and drying the polymer under vacuum, the crude POTV was obtained as a black solid (146 mg, 65%). SEC: M n = 3700, Ð M = 1.47. (M n = 5700, Ð M = 1.57, after Soxhlet extraction).
Catalysts 2019, 9, x FOR PEER REVIEW 2 of 3 A compound 4 (1.90 g, 8.00 mmol) and tetrakis(triphenylphosphine)palladium(0) (0.462 g, 0.40 mmol) were placed in a 100 mL two-necked flask purged with N2. After dissolving the mixture in toluene (40.0 mL), hexamethylditin (2.50 mL, 12.0 mmol) was added, and the mixture was heated to 85 °C and allowed to stand for 8 h. After cooling down to room temperature, the reaction mixture was filtered through celite. It was then extracted with hexane and washed with water and brine. The organic phase was dried over anhydrous magnesium sulfate, filtered, rotary evaporated and purified by sublimation, yielding the title compound as a white crystalline solid (1.22 g, 55%). 1  The compounds of 3 (1.81 g, 4.14 mmol) and 5 (1.14 g, 4.14 mmol), tris(dibenzylideneacetone)dipalladium(0) (0.190 g, 0.207 mmol) and tri(o-tolyl)phosphine (0.317 g, 1.04 mmol) were placed in a 100 mL two-necked flask purged with N2. After dissolving the mixture in toluene (40.0 mL), it was heated to 100 °C and allowed to stand for 2 h. After cooling down to room temperature, the reaction mixture was filtered through celite. It was then extracted with hexane and washed with water and brine. The organic phase was dried over anhydrous magnesium sulfate, filtered, rotary evaporated and purified by silica gel chromatography using hexane/ethyl acetate (7/3) as and eluent to afford OTV as an orange solid (1.22 g, 63%). 1

Synthesis of POTV
The representative experiment for Run 6 (see Scheme 2) is as follows: A 20 mL two-necked flask was first purged with N2 and placed with dehydrated toluene (18 mL), 12-crown-4 ether (8.0 μL, 0.05 mmol) and lithium hexamethyldisilazide (1.3 M in THF, 0.40 mL, 0.52 mmol). After cooling down the flask to −78 °C, the OTV solution (232 mg, 0.495 mmol, 2 mL of toluene) was added to the reaction mixture and allowed to stir for 5 min. The initiator of 5-nitro-2-thiophenecarboxaldehyde (3.4 mg, 0.022 mmol, 0.5 mL of toluene) was added to the mixed solution to start the polymerization. The polymerization was perfomed with stirring at 30 °C for 24 h. To quench the polymerization, a 5 M HCl aq. solution (2 mL) was finally added. The aliquot of the resulted solution was sampled out and extracted with a mixture of chloroform and water. The obtained sample was analyzed by SEC before precipitation. To precpitate the polymer, the rest of the solution was poured into methanol/water (200 mL/ 100 mL). By filtrating and drying the polymer under vacuum, the crude POTV was obtained as a black solid (146 mg, 65%). SEC: Mn = 3,700, ÐM = 1.47. (Mn = 5,700, ÐM = 1.57, after Soxhlet extraction).

Measurements and Characterization
1 H and 13 C nuclear magnetic resonance (NMR) spectra were recorded on a JEOL JNM-ECX400 in chloroform-d at 25 °C or 40 °C, calibrated to chloroform as a standard (δH 7.26). Size exclusion Scheme 2. Synthetic route for POTV (Run 6).

Measurements and Characterization
1 H and 13 C nuclear magnetic resonance (NMR) spectra were recorded on a JEOL JNM-ECX400 in chloroform-d at 25 • C or 40 • C, calibrated to chloroform as a standard (δ H 7.26). Size exclusion chromatography (SEC) was recorded on a Jasco GULLIVER 1500, equipped with an absorbance detector (UV, λ = 254 nm) and three polystyrene gel columns (Eluent: THF, 1.0 mL/min, 40 • C). The M n and M w /M n values of the polymers were calculated from a calibration curve using eight polystyrene standards. A JASCO V-670 spectrophotometer was used for recording UV−vis spectra. The treatment conditions for preparing the thin film samples for the measurement of UV−vis spectra are as follows: (a) dissolution of the polymer in chloroform (~1 mg/mL), (b) drop-cast onto the quartz substrates, and (c) annealing at 200 • C for 10 min. For operating grazing-incidence wide-angle x-ray scattering (GIWAXS), the beamline BL46XU of SPring-8, Japan (proposal No. 2018A1794) was used. The polymer samples for the GIWAXS experiment were prepared as follows: (a) dissolution of the polymer in chloroform (8.0 mg/mL), (b) filtering through PTFE filters (0.45 µm pore size), and (c) spin-coating onto Si wafers. The samples were irradiated at a fixed incident angle α i = 0.12 • , through a Huber diffractometer. The X-ray energy was 12.398 keV (X-ray wavelength λ = 0.10002 nm). The GIWAXS patterns were recorded on a 2D image detector (Pilatus 300K, sample-to-detector distance = 174.4 mm). The scattering vectors q y and q z for GIWAXS are defined in Equation (1).

OFET Fabrication
POTV thin films were deposited onto the substrates, using a customized solution-shearing apparatus equipped with a top shearing blade and temperature-controlled heating stage. POTV were dissolved in chloroform/o-dichlorobenzene (95/5 vol%) co-solvents to prepare the semiconducting ink (10 mg/mL), and then coated onto the PETS-treated Si/SiO 2 substrate for electronic properties characterization. Shearing speed was precisely controlled at 800 µm/s and heating during coating was achieved at a temperature of 35 • C. Post-annealing was performed under vacuum at 80 • C for 3 h. Gold contacts were deposited onto PTOV channel by thermal deposition, at a pressure of 5 × 10 −7 Torr, with shadow mask to form the source and drain electrode. OFETs with a channel length of 40 µm and a width 1000 µm were used. The field effect mobilities were evaluated in the saturation region using the following equation, WC (2) where I d is the drain current, V g gate voltage, L the channel length, W the channel width and C is the capacitance. The slope in I d 1/2 versus V g plots was determined in the saturation region for field effect mobility calculation.

Conclusions
In this study, the atom-economical synthesis of a π-conjugated polymer was reported, based on the aldol condensation reaction free of transition-metals and halogens. Indeed, the synthesis of poly(N-2-hexyldecyloxindolidene thienylene vinylene) (POTV), with a moderate M n = 3700 and Ð M = 1.47 (M n = 5300 and Ð M = 1.57 after Soxhlet extraction), was obtained when using LiHMDS/12-crown-4, OTV, and 5-nitro-2-thiophenecarbaldehyde as a base, monomer, precursor, and initiator, respectively, in toluene/THF at 30 • C. The results of the OFET device indicated that the POTV possesses the potential for organic electronic applications. In the future, toward a better OFET performance, it is expected that a high-molecular-weight POTV with a controllable molecular weight may be obtained by optimizing the polymerization conditions, such as types of the base, temperature, and solvent.