Recent Advances on the Rational Design of Non-Precious Metal Oxide Catalysts Exemplified by CuOx/CeO2 Binary System: Implications of Size, Shape and Electronic Effects on Intrinsic Reactivity and Metal-Support Interactions

Catalysis is an indispensable part of our society, massively involved in numerous energy and environmental applications. Although, noble metals (NMs)-based catalysts are routinely employed in catalysis, their limited resources and high cost hinder the widespread practical application. In this regard, the development of NMs-free metal oxides (MOs) with improved catalytic activity, selectivity and durability is currently one of the main research pillars in the area of heterogeneous catalysis. The present review, involving our recent efforts in the field, aims to provide the latest advances—mainly in the last 10 years—on the rational design of MOs, i.e., the general optimization framework followed to fine-tune non-precious metal oxide sites and their surrounding environment by means of appropriate synthetic and promotional/modification routes, exemplified by CuOx/CeO2 binary system. The fine-tuning of size, shape and electronic/chemical state (e.g., through advanced synthetic routes, special pretreatment protocols, alkali promotion, chemical/structural modification by reduced graphene oxide (rGO)) can exert a profound influence not only to the reactivity of metal sites in its own right, but also to metal-support interfacial activity, offering highly active and stable materials for real-life energy and environmental applications. The main implications of size-, shape- and electronic/chemical-adjustment on the catalytic performance of CuOx/CeO2 binary system during some of the most relevant applications in heterogeneous catalysis, such as CO oxidation, N2O decomposition, preferential oxidation of CO (CO-PROX), water gas shift reaction (WGSR), and CO2 hydrogenation to value-added products, are thoroughly discussed. It is clearly revealed that the rational design and tailoring of NMs-free metal oxides can lead to extremely active composites, with comparable or even superior reactivity than that of NMs-based catalysts. The obtained conclusions could provide rationales and design principles towards the development of cost-effective, highly active NMs-free MOs, paving also the way for the decrease of noble metals content in NMs-based catalysts.


Introduction
The fast growth rate of population in the last decades has led to an unprecedented increase in energy demands. However, the main energy sources fulfilling global demands originate from fossil fuels, rising significant concerns in relation to sources availability and environmental degradation. To this end, the development of emerging energy technologies towards the production of environmentally friendly fuels besides the establishment of cost-effective environmental technologies for climate change mitigation has become a main priority in the scientific and industrial community. Clean and reliable energy supply in conjunction with environmental protection by means of highlyand cost-effective technologies is one of the most significant concerns of the 21st century [1][2][3][4].
In view of the above aspects, heterogeneous catalysis is expected to have a key role in the near future towards sustainable development. Heterogeneous catalysis has received considerable attention from both the scientific and industrial community, as it is a field of diverse applications, including the petrochemical industry with the production of high quality chemicals and fuels, the fields of energy conversion and storage, as well as the remediation of the environment through the abatement of hazardous substances, signifying its pivotal role in the world economy [1,3,[5][6][7].
On the other hand, metal oxides (MOs) prepared from earth-abundant, and inexpensive transition metals have attracted considerable attention as alternatives to rare and expensive NMs, due to their particular features, such as enhanced redox properties, thermal stability and catalytic performance in conjunction to their lower cost [2,3,5,[28][29][30][31][32][33][34][35][36][37][38][39][40][41][42][43]. The latter is clearly manifested in Figure  1, which schematically depicts the cost of noble metals in comparison with copper (a typical transition metal massively involved in MOs) for the past five-year period. It is evident that the price of noble metals is larger than that of copper by about four orders of magnitude. Mixed metal oxides (MMOs) appropriately prepared by admixing two or more single metal oxides in a specific proportion, have lately gained particular attention, since they exhibit unique structural and surface properties, which are completely different from that of parent oxides. Amongst the numerous MOs, transition metal-based oxides have attracted particular attention, due to their peculiar chemisorption capacity, linked to partially filled d-shells [44,45]. For instance, Cu-based oxides can catalyze a variety of reactions following a redox-type mechanism (e.g., photocatalysis), due to the wide range of Cu oxidation states (mainly Cu 0 , Cu I , Cu II ), which enables reactivity in multielectron pathways. On the other hand, reducible oxides, such as ceria, not only provide the basis of active phase dispersion, but could have a profound influence on the intrinsic catalytic activity, through metal-support interactions, as will be further discussed in the sequence. In particular, ceria or cerium oxide (CeO2) has attracted considerable attention, due to its unique properties, including enhanced thermal stability, high oxygen storage capacity (OSC) and oxygen mobility, as well as superior reducibility driven by the formation of surface/structural defects (e.g., oxygen vacancies) through the rapid interplay between the two oxidation states of cerium (Ce 3+ /Ce 4+ ) [2,6,38,[46][47][48]. Besides bare ceria's exceptional properties, its combination with transition metals leads to improved catalytic performance, due to the synergy between the metal phase and the support, related to electronic, geometric and bifunctional interactions [40,[49][50][51][52][53][54]. In this regard, the combination of CuOx and CeO2 oxides towards the formation of CuOx/CeO2 binary oxides, offers catalytic activities comparable or even better to NMs-based catalysts in various applications, such as CO oxidation, N2O decomposition, preferential oxidation of CO (CO-PROX), as lately reviewed [40].
The peculiar reactivity of CuOx/CeO2 system arises not only from the distinct characteristics of individual CuOx and CeO2 phases, but mainly from their synergistic interactions. More specifically, the synergistic effects between the different counterparts of MOs can offer unique characteristics (e.g., improved reducibility, abundant structural defects, etc.), reflected then on the catalytic activity [40,[55][56][57][58][59][60]. Various interrelated factors are usually considered under the term "synergy", involving among others: (i) The superior interfacial reactivity as compared to the reactivity of individual particles; (ii) The presence of defects (e.g., oxygen vacancies); (iii) The enhanced reducibility of MOs as compared to single ones; (iv) The interplay between interfacial redox pairs (e.g., Cu 2+ /Cu + and Ce 3+ /Ce 4+ ).
In view of the above, very recently, the modulation of metal-support interactions as a tool to enhance the catalytic performance was thoroughly reviewed, disclosing that up to fifteen-fold productivity enhancement can be achieved in reactions related to C1 chemistry by controlling metalsupport interactions [61]. However, it is well established today-thanks to the rapid development of sophisticated characterization techniques-that various interrelated factors, such as the composition, the size, the shape, and the electronic state of MOs different counterparts can exert a profound influence on the local surface chemistry and metal-support interactions, and in turn, on the catalytic activity of these multifunctional materials [6,48,51,52,[62][63][64][65][66][67][68][69][70][71][72][73][74]. In view of this fact, the fine-tuning of MOs towards the development of catalytic materials with the desired cost, activity, selectivity and stability could be considered the "Holy Grail" in the field of catalyst manufacturing. Size, shape, porous, redox and electronic adjustment by means of appropriate synthetic and promotional/modification routes can provide the vehicle to substantially modify not only the reactivity of metal sites in its own right, but also the interfacial activity, offering highly active and stable materials for real-life energy and environmental applications (Figure 2). . Figure 2. Schematic illustration of metal oxides (MOs) fine-tuning by adjusting their size, shape, composition and electronic/chemical state.
In light of the aforementioned issues, the present review article aims to gain insight into the particular effect of each adjusted parameter on MOs physicochemical characteristics and in turn, on their catalytic performance, towards revealing rigorous structure-property relationships. The basic principles of MOs fine-tuning by modulating the size, shape and electronic/chemical state by means of appropriate synthetic/modification routes will be initially presented. The implications of size, shape and electronic/chemical effects in catalysis will be next exemplified on the basis of state-of-theart catalytic applications of CuOx/CeO2 binary oxide, involving CO oxidation, N2O decomposition, preferential oxidation of CO (CO-PROX), water gas shift reaction (WGSR), and CO2 hydrogenation to value-added chemicals/fuels. It should be noted here that the scope of the present article is not to provide a complete survey in relation to the fundamental understanding and practical applications of CuOx/CeO2 system, which can be found in various comprehensive reviews [40,49,[75][76][77]. Herein, the CuOx/CeO2 system is used as an excellent benchmark to reveal how we can adjust the local surface chemistry and in turn, the catalytic activity of MOs. The obtained conclusions can provide rationales and design principles towards the development of cost-effective, highly active NMs-free MOs of various compositions, paving also the way for the decrease of noble metals content in NMs-based catalysts. The term "CuOx" instead of CuO is used throughout the text to denote the differentiation of Cu oxidation state depending on synthesis procedure and reaction environment, as discussed in the sequence.

Fine-Tuning of Metal Oxides (MOs)
Heterogeneous catalysis traditionally refers to a chemical reaction on the surface of a solid catalyst, involving adsorption and activation of reactant(s) on specific active sites, chemical transformation of adsorbed species and products desorption. Thanks to the rapid development of both in situ and ex situ characterization techniques, it is well acknowledged that the elementary reaction steps are strongly dependent on several parameters involving the size, the shape, the electronic state of individual particles, as well as on their interfacial interactions. Hence, the macroscopic catalytic behavior can be considered as the outcome of interactions between reactants, intermediates and products with the micro(nano)scopic coordination environment of surface atoms, involving geometric arrangements, electronic confinement, and interfacial effects, among others. In view of this fact, the modulation of the above-mentioned parameters can profoundly affect the local surface structure and chemistry with great implications in catalysis. It should be mentioned, however, that due to the interplay between structural and chemical factors, it is quite challenging to disclose the fundamental origin of catalytic performance. Thus, it is of vital importance to establish reliable structure-property relationships, unveiling the particular role of each factor. The latter could lead to rational design instead of trial-and-error methods by utilizing the fundamental knowledge at the nanoscale.
Moreover, taking into account that the majority of MOs consists of at least two different counterparts, this triggers unique opportunities towards designing various MOs of the same composition, but of different reactivity by adjusting the above-mentioned parameters either in one or both counterparts. For instance, by modulating the size, morphology and electronic/chemical state of ceria carrier in CuOx/CeO2 composites, a different extent of metal-support interactions can be attained with implications in catalysis. In a similar manner, the co-adjustment of the shape of both CuOx and CeO2 could lead to different synergistic interactions, providing CuOx/CeO2 systems of peculiar reactivity. The proposed adjusting approach on the way to fine-tune MOs is schematically illustrated in Figure 3, clearly revealing the unique opportunities in the field of materials synthesis and engineering towards the development of low-cost and highly-effective composites. In the following, the basic principles of size, shape, and electronic/chemical effects are provided in separate sections. It should be stressed, however, that this district presentation does not also mean a district effect of each factor in catalysis. Almost all parameters are interrelated; thus, the discrete role of each one in the catalytic activity of MOs cannot be easily disclosed, as further discussed below.

Size Effects
The rapid development of nanotechnology in the last years enables the fabrication of MOs with tunable size and shape at the nanometer scale. Nowadays, it has been both experimentally and theoretically revealed that the surface, structural and electronic properties of nanoparticles (NPs) differ essentially from the corresponding bulk properties. In general, by decreasing the particle size of metal oxide particles down to few nanometers (e.g., <10 nm), a dramatic increase in activity can be generally obtained, attributed to "size effects". This size-dependent reactivity can be ascribed to different contributions, namely: (i) Quantum size effects, (ii) presence of low coordinated atoms into NPs surface, (iii) electronic state of the surface, (iv) strong interparticle interactions. Hereinafter, the particular effect of every contribution is shortly presented for the sake of following discussions in relation to the fine-tuning of MOs. For additional reading, several comprehensive articles in this topical area are recommended [40,52,62,66,70,71,74,78].
In particular, by decreasing the size of a material down to nanometer scale, the surface-tovolume ratio is largely increased, resulting in an increased population of surface sites, being the active sites in catalysis. Besides the modulation of the fraction of atoms on the topmost surface layer, the number of atoms at corners and edges, being considered more active than those at planes, is considerably increased by decreasing the size. More specifically, size decrease leads to a high density of under-coordinated atoms with exceptional adsorption and catalytic properties [52,62,70,[79][80][81][82][83]. Typically, surface sites with low coordination number (CN) demonstrate stronger adsorption ability as compared to those of high CN [66,70,84]; linear relationships between the adsorption energy of various adsorbates and the coordination number have been found for several transition metals, including among others non-precious metals, such as Cu, Ni, and Co [85,86]. Thus, from the geometrical point of view, size decrease has a direct effect on both the number and type of active surface sites reflected then on catalytic activity.
Aside from the "geometric size effects", the electronic state of surface atoms can undergo substantial modifications upon decreasing the particle size down to nanometer scale. In particular, when a bulk material with a continuous electron band is subjected to size decrease down to the nanoscale, the so-called quantum effect or confinement effect is taking place, arising from the presence of discrete electronic states as in the case of molecules [62,70,74,78,87]. For instance, it has been reported that a higher electron density, with a d band close to the Fermi level, can be obtained for Au NPs smaller than ca. 2 nm as compared to bigger ones, with great implications in CO oxidation [88][89][90][91].
Recently, thanks to the introduction of new generation sophisticated characterization techniques (e.g., high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM), extended X-ray absorption fine structure (EXAFS)) and computational methods (e.g., DFT calculations), an indirect size effect linked to the metal-support interactions is clearly revealed. More specifically, even small perturbations between metal nanoparticles and oxide carriers, due to charge transfer between particles, local electric fields, morphological changes, "ligand" effect, etc., can induce a substantial modification in catalytic activity [40,50,55,[92][93][94][95]. To more accurately describe these phenomena, the term Electronic Metal Support Interactions (EMSI) has recently been proposed by Campbell [96] in contrast to classical Strong Metal Support Interactions (SMSI). In view of this concept, tiny metal clusters composed of a few or even single atoms could play a dominant role in catalysis, despite the fact that they do not account for more than a few percent of the total metal content [40,50]. In view of this fact, it has been shown that by controlling metal (Ni, Pd, Pt) nanocrystal size, the length of metal-ceria interface is appropriately adjusted with significant implications in CO oxidation; normalized reaction rates were dramatically increased with decreasing the size, due to the increased boundary length (Figure 4). . The calculated number of sites with a particular geometry (surface and perimeter or corner atoms in contact with the support) as a function of diameter and the turnover frequency (TOF) at 80 °C for ceria-based metals (Ni, Pd, Pt). Reproduced with permission from Reference [52]. Copyright © 2020 , American Association for the Advancement of Science (AAAS).
As an additional implication of size-dependent behavior, the significant effect of particle size on structural defects of reducible carriers (such as ceria) should be mentioned. In fact, a close relationship between the crystal size of ceria and the concentration of oxygen vacancies has been revealed; the large surface-to-volume ratio in conjunction to the exposure of under-coordinated sites can facilitate the formation of oxygen vacancies and the Ce 3+ fraction in non-stoichiometric CeO2-δ NPs [71,[97][98][99][100][101][102][103]. Moreover, an inverse correlation between the lattice parameters of CeO2 NPs and particle sizes has been established (Figure 5a), attributed to the increase of Ce 3+ and oxygen vacancies concentration [71]. A similar trend was recorded between the surface-to-bulk oxygen ratio and particle size ( Figure  5b).
Closing this part concerning the size effects, it should be noted, that although particle size decrease has, in general, a positive catalytic effect, there is a variation in relation to size-activity relationships depending on catalyst type and reaction environment. For instance, a positive size effect could be obtained if the rate determining step (rds) involves the bond cleavage of a reactant molecule on surface atoms with low coordination number. However, if the same under-coordinated atoms strongly bind dissociated species (e.g., oxygen atoms), this could lead to the poisoning of catalyst surface, and thus, to the negative size effect. In particular, in reactions with no structure sensitivity, the activity remains unaffected by changes in the particle size, while it could decrease with decreasing particle size, referred as negative particle size effect or antipathetic structure sensitivity, or increase as the particle size decreases, referred as positive particle size effect or sympathetic structure sensitivity [79]. Moreover, the activity may reach a maximum when small particles exhibit a negative effect, and larger particles show a positive one [79].  [71]. Copyright © 2020 , Royal Society of Chemistry.

Shape Effects
Nanostructured catalysts possess unique properties originating from nanoscale phenomena linked mainly to size effects, commented above, and shape effects. The latter refers to the modification of catalytic activity through the preferential exposure of specific crystallographic facets on the reaction environment, also termed as morphology-dependent nanocatalysis [51,65,66,70,82,[104][105][106]. In particular, the catalytic cycle and hence the reaction efficiency, is determined on reactants adsorption/activation and products desorption processes, being strongly influenced by the surface planes of catalysts particles. In this regard, the simultaneous modulation of size and shape at the nanometer scale can determine the number and the nature of exposed sites, and thus, the catalytic performance. This particular topic is an essential issue within the field of nanocatalysis, aiming to the control of a specific chemical reaction through co-adjusting these parameters at the nanometer scale.
Thanks to the latest advances in materials science, nanostructured catalysts with well-defined crystal facets can be fabricated by precisely controlling nanocrystals nucleation and growth rate [48,63,66,67,78,105]. The obtained crystal morphology is the result of several synthesis parameters, involving temperature, pressure, concentration, and pH, among others. Several reviews have been devoted to the subject [6,38,67,82,97,105,107,108]. Various structures with similar or different dimensions in all directions, such as nanospheres, nanocubes, nanowires, nanorods, nanosheets, etc., could be obtained.
The shape control of ceria and its implications in catalysis is most probably the most extensively investigated system among metal oxides in heterogeneous catalysis [2,6,38,48,51,64,65,73,82,97,104,107,[109][110][111][112]. The growth rate mechanism of ceria nanocrystals can be affected by various parameters, such as the basicity or polarity of the solvent [113,114], the aging temperature [115,116], the precursor compound [117,118], and the impregnation medium [119]. Regulation of nanocrystals nucleation and growth processes results in specific shapes, such as rods and cubes [48,67]. Moreover, by altering the physicochemical conditions during the synthesis procedure (e.g., by the usage of a capping agent), blocking of certain facets or continuous growth of others may occur.
In view of the above, it has been clearly revealed that the activity and selectivity are strongly affected by the exposed crystal planes. For instance, the formation rate of ammonia on Fe crystals follows the sequence: {111} >> {100} > {110} [167]. Similar morphology-dependent effects have been demonstrated for several noble metal [105,168] and metal oxide [51] catalyzed processes.
Very recently, we showed that among ceria nanoparticles of different morphology (nanocubes, nanorods and nanopolyhedra), as shown in Figure 7a, ceria nanorods with {100} and {110} crystal planes, exhibited the optimum redox properties in terms of loosely bound oxygen species population [115,121]. Figure 7b depicts the H2 temperature-programmed reduction (H2-TPR) profiles of ceria nanocubes, nanopolyhedra and nanorods, where two main peaks at ca. 550 and 800 °C can be identified, ascribed to the reduction of surface (Os) and bulk (Ob) oxygen, respectively. Notably, the surface-to-bulk (Os/Ob) ratio is strongly dependent on ceria morphology following the order: NC (0.71) < NP (0.94) < NR (1.13). It is also worth mentioning that the onset reduction temperature follows the reverse order, i.e.,: NC (589 °C) > NP (555 °C) > NR (545 °C), implying the lower temperature reduction of {110} and {100} surfaces as compared to {111}. More recently, we explored the impact of ceria exposed facets on structural defects by means of in situ Raman spectroscopy following a novel approach involving sequential spectra acquisition under alternating oxidizing and reducing atmospheres [115]. The in situ Raman measurements perfectly corroborated the aforementioned arguments in relation to the impact of crystal planes on the reducibility; the relative abundance of defects and oxygen vacancies exhibited by the ID/IF2g ratio, as well as the relative reducibility expressed by the detachment of O atoms and the partial Ce 4+ → Ce 3+ reduction, follow the same trend, i.e., NR > NP > NC.
These results unambiguously indicate that CeO2-nanorods exhibit the highest concentration of weakly bound oxygen species, linked to enhanced reducibility and oxygen mobility. Interestingly, an almost linear relationship is revealed between the redox properties, expressed either as Os/Ob or ID/IF2g ratio, and the CO oxidation performance, in terms of half-conversion temperature (T50), of ceria nanoparticles (Figure 7c), clearly demonstrating the implications of shape modulation in catalysis.

Electronic Effects
Besides modulating the local surface structure of MOs by size and shape effects, described above, the fine-tuning of electronic structure by appropriate promoters can be considered as an additional modulating tool. Promoters hold a key role in heterogeneous catalysis towards optimizing the catalytic activity, selectivity and stability by modifying the physicochemical features of MOs, and can be classified into two general categories: Structural promoters and electronic promoters. The first category mainly involves the doping of supporting carrier to enhance its structural characteristics and in turn, the stabilization of active phase (e.g., incorporation of rare earth dopants into three-way catalysts [5]). On the other hand, electronic promoters can modify catalysts surface chemistry either directly or indirectly. The former mainly includes the electrostatic interactions between the reactant molecules and the local electric field of promoters. The latter denotes the promoter-induced modifications on metal Fermi level, which is then reflected on the chemisorptive bond strength of reactants and intermediates with great consequences in catalysis. In particular, "promoter effect" is related to the changes in the work function (Φ) of the catalysts surface upon promoter addition, accompanied by substantial modification of its chemisorption properties. The vast majority of electronic promotion over metal oxide catalysts refers to alkali modifiers. It has been well documented that alkali addition can drastically enhance the activity and selectivity of numerous catalytic systems, involving among others Pt-, Pd-, Rh-, Cu-, Fe-based catalysts, in various energy and environmental related reactions (e.g., [169][170][171][172][173][174]). Various comprehensive studies have been devoted to the role of promoters in heterogeneous catalysis, to which the reader can refer for further reading [175][176][177].
Figures 8 and 9 depict the "promoter effect" in the case of alkali-doped Co3O4 oxides during the N2O decomposition [178,179]. A close relationship between the catalytic performance (in terms of half-conversion temperature, T50) and the work function (Φ) was disclosed revealing the electronic nature of alkali promotion; electropositive modifiers (such as alkalis) can decrease the work function of the catalyst surface, thus, activating the adsorption/decomposition of electron-acceptor molecules (such as N2O) [178]. However, at high alkali coverages, depolarization occurs, due to the strengthening of the alkali-alkali bond at the expense of the alkali-surface bond, resulting in a work function increase [180]. Adapted from Reference [178]. Copyright © 2020 , Elsevier. In this point, it should be mentioned that, depending on the support nature and crystal planes, alkali adsorption may lead to surface reconstruction. This surface reconstruction can be explained by taking into account the structural/electronic perturbations induced by the formation of the alkalisurface bond [181]. As mentioned previously, the crystallographic orientation of the support plays an important role in the diffusion rate of the adsorbed species, as well as in their in-between interaction, resulting in different structural stabilization [181]. For instance, potassium promoter was shown to stabilize certain iron facets in K-promoted iron catalysts, by inducing changes in the crystal growth rate, thus, enabling the formation of small particles with abundance in active facets and affecting the activity and selectivity of the overall system [182]. As shown in Figure 10, by increasing the K/Fe surface atomic ratio, the crystal facets become more stable and the surface energy is decreased [182]. This clearly manifests the pivotal role of alkali addition towards co-adjusting the structural and electronic properties of the catalyst surface, and in turn, the catalytic performance. Besides the alkali-induced modifications on the chemisorption properties, significant alterations on the surface oxygen mobility have been demonstrated; alkali addition could facilitate suprafacial recombination of oxygen towards molecular oxygen desorption, thus, liberating active sites [40]. Both the electronic and redox modifications induced by alkali addition can exert remarkable effects on catalytic activity and selectivity, demonstrating the key role of "promoter effect" as an additional adjusting parameter in catalysis.
It should be noted here, as mentioned in the case of size and shape effects, that the promoter effect is not always positive. The latter strongly depends on reactants type (electron donor or electron acceptor adsorbates) and the work function changes (increase or decrease) induced by the promoter (electropositive or electronegative). Thus, besides the structure-sensitivity, commented above, the electronic-sensitivity of a given reaction should always be taken into account, when attempting to coadjust the size, shape and electronic state. Although, this is not an easy task, it could be an effective approach towards designing cost-effective and highly active composites, as revealed in the sequence.

Chemical Modifiers
Besides the extensive use of alkalis or alkaline earths as promoters, numerous other chemical substances can be employed to modulate the local surface chemistry/structure and in turn, the activity, selectivity and long-term stability of parent catalyst (e.g., [74]). In this regard, metal alloys (e.g., Au-Ni alloys as reforming catalysts [183], Pt-Sn alloys for ethanol oxidation [184]) are extensively employed in catalysis towards obtaining highly active and cost-effective catalytic formulations. Several mechanisms are considered responsible for the enhanced performance of bimetallic systems, involving mainly structural (strain effects) and electronic (charge-transfer effects) modifications that can be induced by the interaction between the different counterparts. The latter substantially modifies the binding energy of adsorbates and the path of chemical reactions with major consequences in catalysis [50,74].
In a similar manner, chemical substances with unique physico-chemical properties, such as carbon-based materials, have lately received considerable attention as chemical modifiers or supporting carriers [62,185]. Various carbon materials, such as carbon nanotubes (CNTs), reduced graphene oxide (rGO), ordered mesoporous carbon (OMC), carbon nanofibers (CNFs), and graphitic carbon nitride (g-C3N4), have received particular attention in catalysis after the significant progress in controlled synthesis and the fundamental understanding of their properties. In general, nanocarbons (NCs) possess unique physical (large surface area, specific morphology, appropriate pore structure) and chemical (electronic structure, surface acidity/basicity) properties arising from their nanoscale confined structures [185].
The combination of metal nanoparticles (NPs) with carbon materials by means of various synthetic approaches can exert significant modifications on the structural and electronic surrounding of NPs with subsequent implications in catalysis [62,185]. As for example, confined Fe NPs in CNTs exhibit an almost twice yield to C5+ hydrocarbons as compared to Fe particles during the syngas conversion to liquid hydrocarbons [186]. The latter was mainly ascribed to the modified structural and redox properties of confined Fe NPs within CNTs [62]. Moreover, the application of graphene in catalysis allows the fabrication of multifunctional materials with distinct heterostructures, which offer quite different properties as compared to individual materials [185,187,188]. In general, carbon materials with exceptional structural and electronic characteristics can be effectively employed either as supporting materials or chemical modifiers, offering unique opportunities towards modulating the intrinsic reactivity of MOs. For instance, it has been found that the homogeneous distribution of copper atoms on the surface of rGO in combination with the outstanding electronic properties of rGO lead to high electrocatalytic activity, due to the synergy between the two components [189].
Metal-organic frameworks (MOFs) are another type of supporting carriers/chemical modifiers consisting of inorganic metal ions or clusters that are bridged with organic ligands in order for one or more dimensional configurations to be formed [190]. These materials exhibit unique properties, such as high surface area and porosity, while their complex network consisting of various channels allows passage in small molecules [191]. The fabrication of MOF-based MOs composites is of great interest, as it results in the development of materials with tunable properties and functionality. Metal nanoparticles regarded as the active centers can be stabilized by MOFs through confinement effects [192]. As for example, Cu, Ni, and Pd nanoparticles encapsulated by MOFs exhibited high catalytic efficiency, ascribed mainly to the synergistic effects of nanoconfinement and electron-donation offered by MOF framework [193][194][195][196][197][198]. Furthermore, by changing the MOFs functional groups, products distribution may differ, as a consequence of variations induced in the chemical environment of the catalytically active sites [199].

Pretreatment Effects
Besides the advances that can be induced by adjusting the size, shape and electronic state of MOs, special pretreatment protocols or activation procedures could be applied to further adjust the local surface chemistry of MOs (e.g., [200,201]). In particular, the local surface chemistry of the MOs can be further tailored by appropriate pretreatment protocols, including thermal or chemical pretreatment. According to the pretreatment protocol followed, different properties get affected, resulting in diversified catalytic behavior. By way of illustration, it has been reported that defect engineering by a low-pressure thermal process instead of atmospheric pressure activation, could notably increase the concentration of oxygen vacancy defects and in turn, the CO oxidation activity of ceria nanoparticles, offering an additional tool towards the fine-tuning of MOs [200]. Moreover, it has been documented that the pretreatment protocol (oxidation or reduction) induces significant effects on the local surface structure of cobalt-ceria oxides affecting the dehydroxylation process in ammonia synthesis [202]. In a similar manner, oxidative pretreatment of cobalt-ceria catalysts resulted in an impoverishment of catalyst surface in cobalt species, due to the preferential existence of cerium species on the outer surface, whereas, cobalt and cerium species are uniformly distributed on the catalyst surface through the reduction pretreatment, which gives rise to the formation of oxygen vacancies [33]. In addition, a strong interaction between gold and ceria has been observed after O2 pretreatment, due to the electron transfer from Au 0 to ceria, giving rise to oxygen vacancy formation, lattice oxygen migration, as well as to the formation of Au δ+ -CO and surface bicarbonate species, favoring, thus, the adsorption of CO and the desorption of CO2 [203]. In terms of T100, CO oxidation performance showed the following order: O2 pretreatment (74 °C) < N2 pretreatment (142 °C) < 10% CO/Ar pretreatment (169 °C) [203]. In view of the above short discussion, the pretreatment conditions can affect the facilitation with which certain active species are formed on the catalyst surface, the oxygen mobility or the formation of oxygen defects, with great implications in the catalytic performance.

Implications of MOs Fine-Tuning in Catalysis Exemplified by CuOx/CeO2 Binary System
In this section, the implications of metal oxides fine-tuning by means of the above-described size, shape and electronic/chemical effects are presented, on the basis of the CuOx/CeO2 binary oxide system. This particular catalytic system is selected as representative MOs, taking into account the tremendous fundamental and practical attention lately devoted to the copper-containing cerium oxide materials. More specifically, the abundant availability of copper and ceria and consequently, their lower cost (about four orders of magnitude, Figure 1) render CuOx/CeO2 composites strongly competitive. Moreover, their excellent reactivity-linked to peculiar metal-support interactions-in conjunction to their remarkable resistance to various substances, such as carbon dioxide, water and sulfur is of particular fundamental and practical importance [57,76,204]. Remarkably, coppercontaining ceria catalysts appropriately adjusted by the aforementioned routes demonstrated catalytic activity similar or even better than NMs-based catalysts in various applications, such as CO oxidation, the decomposition of N2O and the water-gas shift reaction, among others [115,124,159,[205][206][207][208][209][210][211][212][213][214][215][216].
For instance, the inverse CeOx/Cu(111) system exhibits superior CO oxidation performance at a relatively low-temperature range (50-100 °C), in which the noble metals do not function well, exhibiting activity values of about one order of magnitude higher than those measured on Pt(100), Pt (111), and Rh (111) [217][218][219]. The latter has been mainly attributed, on the basis of the most conceptual experimental and theoretical studies, to the existence of Ce 3+ at the metal-oxide interface which binds O atoms weaker as compared to bulk Ce 3+ [217,220].
In light of the above aspects, in this section, the main implications of size, shape and electronic/chemical effects on the catalytic performance of CuOx/CeO2 system during some of the most relevant applications in heterogeneous catalysis will be discussed. It should be stressed that it is not the aim of this section to provide an extended overview of CuOx/CeO2 catalytic applications, which can be found in several comprehensive reviews [3,49,57,75,76,221]. It mainly aims to provide a general optimization framework towards the development of highly active and cost-effective MOs, paving also the way for the decrease of precious metal content in NMs-based catalysts.

CO Oxidation
CO oxidation is probably the most studied reaction in heterogeneous catalysis, due to its practical and fundamental importance. The catalytic elimination of CO is of great importance in various applications involving, among others, automotive exhaust emissions control and fuel cell systems. More importantly, CO oxidation can serve as a prototype reaction to gain insight into the structure-property relationships.
Regarding, at first, the CO oxidation activity of individual CuOx phase, it has been clearly revealed that it is strongly dependent on oxidation state, size and morphology. In particular, the following activity order: Cu2O > metastable cluster CuO > CuO has been revealed, closely related to the ability to release lattice oxygen [222,223]. On the other hand, the exposed crystal planes of CuOx phase drastically affect the CO oxidation; truncated octahedral Cu2O with {332} facets displayed better activity than low index {111} and {100} planes [224]. Similarly, CuO with exposed {011} planes is more active that close-packed {111} planes [225]. In view of this fact, it has been found that the CO oxidation activity of CuO mesoporous nanosheets with high-index facets is about 35 times higher than that of the commercial sample [226]. In general, surface vacancies, originated from coordinately unsaturated surface Cu atoms, can easily activate oxygen species towards their reaction with the reducing agent [3].
In a similar manner, theoretical and experimental studies have shown that the energy of anionic vacancies formation over bare ceria follows the order: {111} > {100} > {110}, as previously analyzed [82, 104,109,112,146,[160][161][162][163][164][165][166]. Moreover, a large increase in oxygen vacancies concentration has been found for ceria crystal size lower than ca. 10 nm [98], revealing the interrelation between size and shape effects. In this regard, we recently showed that ceria nanorods with {100} and {110} exposed facets demonstrated the optimum CO oxidation activity amongst ceria samples of different morphology; a close relationship between crystal planes-oxygen exchange kinetics-CO oxidation activity was disclosed [115].
In view of the above aspects, it could be argued that by adjusting the shape and size of individual counterparts of MOs (CuOx and CeOx in the case of CuOx/CeO2 mixed oxides), significant modifications in their redox and catalytic properties can be obtained. However, in view of the fact that "the whole is more than the sum of its part", the majority of catalytic studies in heterogeneous catalysis is based on CuOx/CeO2 mixed oxide than on individual oxides [52,227,228]. The underlying mechanism of this synergistic effect linked to metal-support interactions is the subject of numerous theoretical and experimental studies in catalysis. The latest advances in the field of CuOx-CeO2 interactions and their implications in catalysis have been recently reviewed by one of us [40]. In general, the superiority of binary oxides can be ascribed to various interrelated phenomena, involving among others: (i) Electronic perturbations between nanoparticles, (ii) redox interplay between interfacial sites, (iii) facilitation of the formation of structural defects, (iv) improved reducibility and oxygen mobility, (v) unique reactivity of interfacial sites [40]. However, all of these factors are closely related with the intrinsic and extrinsic characteristics of individual oxides, triggering unique opportunities towards the development of highly active MOs by engineering the size and shape of individual oxides and in turn, the interfacial reactivity . Moreover, chemical or electronic effects induced by aliovalent doping can exert a profound influence on the catalytic performance, offering an additional tool towards the rational design of MOs (Figure 2). In the sequence, the optimization of CO oxidation activity of CuOx/CeO2 catalysts by means of the abovementioned approaches is presented, as an indicative example of MOs rational design.
Recently, we thoroughly explored the impact of ceria nanoparticles shape effects on the CO oxidation activity of CuOx/CeO2 catalysts. The results clearly revealed the significant role of morphology in the CO oxidation activity, following the order: Nanorods (NR) > nanopolyhedra (NP) > nanocubes (NC), Figure 11. However, more importantly, CuO incorporation to different ceria carriers boosted the catalytic performance, without affecting the order observed for bare CeO2 ( Figure  11), demonstrating the crucial role of support. The CuOx/CeO2-NR sample exhibited a half-conversion temperature (T50) of ca. 70 °C, which is much lower to that required for a typical noble metal oxidation catalyst, such as Pt/Al2O3 (T50 = 230 °C), as shown in Figure 12. Based on a thorough in situ and ex situ characterization study, a perfect relationship between the CO oxidation performance and the following parameters was disclosed: (i) Relative population of Cu + /Ce 3+ redox pairs, (ii) abundance of loosely bound oxygen species, expressed in terms of surface-to-bulk oxygen reducibility, (iii) relative concentration of oxygen vacancies, evidenced by the ID/IF2g Raman ratio (Figure 7c) [115]. Similar conclusions in relation to the key role of ceria morphology in the CO oxidation activity have been reported by several groups [117,134,154,158,210,212,[229][230][231], most of these revealing the superiority of nanorods.
However, it should be noted that similar or even better catalytic activities can be obtained by different morphologies (e.g., [124,211,212]). In this regard, it was recently shown that sub-nanometer copper oxide clusters (1 wt.% Cu loading) deposited on ceria nanospheres (NS) exhibited superior performance as compared to that deposited on nanorods (T100 = 122 °C vs. 194 °C) [124]. Extensive characterization investigations revealed that the copper species in nanorods samples existed in both Cu-[Ox]-Ce and CuOx clusters, while CuOx clusters dominated in nanospheres. Among these species, only CuOx clusters could be easily reduced to Cu(I) when they were subjected to interaction with CO, which is considered to be the reason of the enhanced reactivity of CuOx/CeO2-NS samples [124]. So far, numerous synthesis routes and different precursors have been employed to adjust the structural and morphological characteristics of CuOx/CeO2 composites, mostly summarized by Prasad and Rattan [76]. For instance, it has been found that the use of Ce(III) instead of Ce(IV) precursors can lead to CuOx/CeO2 catalysts with superior reducibility and CO oxidation activity [232]. In particular, it was experimentally shown that Ce(III)-derived samples contained a higher amount of Cu + species, through the redox equilibrium Cu 2+ + Ce 3+ ↔ Cu + + Ce 4+ , which are responsible for their enhanced oxidation performance [232]. Moreover, CuOx/CeO2 samples prepared from copper acetate precursor demonstrated better CO oxidation performance as compared to those prepared from nitrate, chloride and sulfate precursors [233]. Avgouropoulos and co-workers [234,235] recently employed a novel hydrothermal method for the synthesis of atomically dispersed CuOx/CeO2 catalysts, offering high CO oxidation performance. By means of various complementary techniques, it was shown that the catalytic activity is mainly related to the nature of highly dispersed copper species rather than the structural/textural characteristics. In a similar manner, Elias et al. [236] reported on the facile synthesis of phase-pure, monodisperse ~3 nm Cu0.1Ce0.9O2-x crystallites via solution-based pyrolysis of heterobimetallic Schiff complexes. An increase of CO oxidation activity by one and three orders of magnitude compared to ceria nanoparticles (3 nm) and microparticles (5 μm), respectively, was attained ( Figure 13). Besides the engineering of shape and size, porous structure engineering could exert a significant influence on the CO oxidation activity of CuOx/CeO2 catalysts [123,213]. As for example, threedimensional CuOx-doped CeO2 prepared by a hard template method exhibited complete CO conversion at temperatures as low as 50 °C, due to their improved textural and redox properties [213].
Regarding the influence of CuOx/CeO2 composition on the CO oxidation activity, most of the studies revealed an optimum Cu/(Cu+Ce) atomic ratio in the range of 15-30% [212,231,232,237,238]. Within this specific range, the optimum physicochemical characteristics and interfacial interactions can be achieved, reflected then on catalytic activity.
Apart from the above-described approaches that have been put forward to improve the CO oxidation performance of CuOx/CeO2 oxides, the addition of aliovalent elements as structural/surface promoters should be mentioned. In view of this fact, it has been found that the modification of ceria support by Mn [239] or Sn [240] can drastically modify the dispersion of CuOx and the redox interplay between Cu species and support, thus, enhancing the CO oxidation performance. Very recently, the tuning of the interfacial properties of CuOx/CeO2 by In2O3 doping was also explored [241]. It was found that the CO oxidation performance of In2O3-CuOx/CeO2 sample greatly exceeds that of parent oxide, offering complete CO conversion at temperatures as low as 100 °C [241]. By means of complementary characterization studies and density functional theory calculations, it was proved that In2O3 could modify the geometric structure of CuOx particles by reducing their size. The latter results in more metal-support interfacial sites and abundant defects. Moreover, the interaction between In and Cu could modify the electronic state of Cu atoms towards the stabilization of partially reduced Cu sites at the interface [241].
Recently, copper-ceria nanosheets were synthesized by using graphene oxide as a sacrificial template, in an attempt to increase the concentration of active interfacial sites [242]. The copper-ceria interaction was further adjusted by appropriate pretreatment, with the catalyst calcined at 600 °C exhibiting complete CO conversion at 90 °C, due to the high concentration in active copper species and oxygen vacancies [242]. Moreover, a sword-like copper-ceria composite derived by a Ce-based MOF with 5 wt.% Cu loading, exhibited superior CO conversion performance (T100 = 100 °C) in comparison to other irregular-shaped catalysts, due to the good interfacial contact, which resulted in the abundance of Cu + active species and oxygen vacancies [191]. Very recently, triple-shelled CuOx/CeO2 hollow nanospheres were synthesized by MOFs, exhibiting high CO conversion performance (T100 = 130 °C) [243]. This was mainly ascribed to the porous structure of the tripleshelled morphology, offering an enhanced synergistic interaction between copper and ceria [243]. Table 1 summarizes, at a glance, indicative attempts followed to adjust the interfacial properties and in turn, the CO oxidation performance of CuOx/CeO2 binary oxides. It is evident that extremely active composites can be obtained by adjusting the shape, size and electronic/chemical state by means of appropriate synthetic and/or promotional routes. It is of worth pointing out the superiority of finely-tuned CuOx/CeO2 samples as compared to noble metal-based catalysts, offering unique opportunities towards the rational design of highly active metal oxide catalysts. Moreover, as further guidance, it would be of particular importance to explore the combining effect of different adjusted parameters (e.g., CuOx/CeO2 nanorods co-doped with main-group elements) towards further optimization.

N2O Decomposition
Nitrous oxide (N2O) has been lately recognized as one of the most potent greenhouse gases and ozone depleting substances [246]. In view of this fact, the catalytic abatement of N2O has received particular attention as one of the most promising remediation methods. Although noble metals exhibit satisfactory activity, their high cost and sensitivity to various substances (e.g., O2, H2O) hinder widespread applications. Hence, as previously stated, noble metal-free composites have gained particular attention as potential candidates. The recent advances in the field of N2O decomposition over metal oxides have been recently reviewed by Konsolakis [246]. It was clearly revealed that MOs could be effectively applied for N2O decomposition, demonstrating comparable or even better catalytic performance compared to NMs-based catalysts. More interestingly, and in line with the aim and scope of the present article, it was shown that very active and stable MOs could be obtained by adjusting their size, shape and electronic state through appropriate synthesis and promotional routes [246].
Herein, we shortly present the main approaches lately followed to improve the deN2O performance of MOs, exemplified by the CuOx/CeO2 system. Table 2 presents indicative studies towards this direction, involving our recent advances in the field [215,247]. It is of worth noticing the comparable or even superior deN2O performance of finely-tuned CuOx/CeO2 samples as compared to noble metal-based catalysts (Table 2).
The effect of ceria morphology (nanorods, nanocubes, nanopolyhedra) on the deN2O performance of CuOx/CeO2 composites was extensively investigated by Pintar and co-workers [146]. Copper clusters located on {100} and {110} planes-preferentially exposed on ceria nanorods-exhibit a normalized activity ca. 20% higher compared to {111} planes of polyhedra ( Figure 15). In terms of conversion performance, the 4.0 wt.% CuOx/Ceria-nanorods exhibited a half-conversion temperature (T50) of about 430 °C compared to 440 °C and 470 °C of nanopolyhedra and nanocubes, respectively. On the basis of a thorough characterization study, it was disclosed that the oxygen mobility and the regeneration of active Cu phase are easier on ceria nanorods, which in turn, facilitates the deN2O activity through oxygen desorption and replenishment of active sites [146]. In a similar manner, CuOx supported on CeO2 nanospheres exhibited high deN2O performance (T50 = 380 °C, Table 2), ascribed mainly to the high population of CuOx clusters on the high surface area CeO2 nanospheres [205]. These findings clearly demonstrate the significant advances that can be achieved in the deN2O process by engineering the size and shape of metal oxide composites. Figure 15. The activity of nanoshaped CuOx/CeO2 catalysts measured at T = 375 °C. Adapted from Reference [146]. Copyright © 2020 , American Chemical Society.

Preferential Oxidation of CO (CO-PROX)
The copper-ceria binary oxides are amongst the most widely investigated catalytic systems in the preferential oxidation of carbon monoxide (CO-PROX), a reaction used for the production of highly purified hydrogen and the removal of CO. CuOx/CeO2 catalysts have gained particular attention in CO-PROX process, due to their superior performance, which is mainly ascribed to the peculiar properties of copper-ceria interface [40].
In the light of the above-mentioned size, shape and electronic/chemical effects, numerous efforts have been put forward towards optimizing the CO-PROX performance. Indicative approaches followed to fine-tune the CO-PROX performance are summarized in Table 3, and further discussed below. Several copper-ceria catalytic systems of various copper loadings have been synthesized by different methods, with the optimum Cu loading varying between 5 and 10 wt.% [250,[252][253][254]265]. A further increase in Cu content from 10 to 15 wt.% has been reported to reduce the catalytic activity, due to the large CuOx agglomerates on the catalyst surface [252]. It was revealed, by means of both ex situ and in situ characterization studies, that the desired CO oxidation process is related to partially reduced Cu + species, whereas, highly reduced copper species not strongly associated with CeO2 favor the undesired H2 oxidation [40,250,[265][266][267]. In view of this fact, extensive research efforts have been put forward to control the two competitive oxidation processes by appropriately adjusting the geometric and electronic interactions between copper and ceria through the above-described finetuning approaches.
Regarding the shape effect, different copper-ceria nanostructures (rods, cubes, spheres, octahedra, spindle or multi-shelled morphologies) have been synthesized and studied for the CO-PROX reaction. It was revealed that the shape-controlled synthesis of ceria nanoparticles has a profound influence on the CO-PROX activity and selectivity. In particular, it was found that rodshaped and polyhedral copper-ceria systems exhibited higher CO conversion performance (T50 = 68 °C) at low-temperatures, as compared to plates (T50 = 71 °C) and cubes (T50 = 89 °C) [157]. The latter was mainly attributed to the smaller CuOx clusters subjected to a strong interaction with the ceria carrier, which, in turn, facilitates the formation of Cu + sites and oxygen vacancies [157]. More importantly, a close relationship between measurable physicochemical parameters, such as the amount of Cu + species and the A584/A454 Raman ratio (related to oxygen vacancies) with the catalytic performance was obtained ( Figure 16); rod-and polyhedral-shaped samples exhibited the highest values on Cu + species and oxygen vacancies, demonstrating, also, the optimum CO-PROX performance [157]. In this point, it should be mentioned that in relation to which ceria shape is the most active or selective for the CO-PROX process, inconclusive results are acquired, due to the different reaction conditions applied (see Table 3) in conjunction to the complexity of CO-PROX process, which is affected to a different extent by the various interrelated parameters (e.g., reducibility, metal dispersion, oxygen vacancies, oxidation state, metal-support interactions). Under this perspective, it was reported that copper-ceria nanocubes exhibited higher CO2 selectivity than copper-ceria nanorods or nanospheres, due to the difficulty of nanocubes to fully reduce the copper oxide species under CO-PROX conditions [133,268], while, at the same time, exhibiting lower CO conversion than nanorods [268] and nanospheres [133]. In a similar manner, CuOx/CeO2 spheres and spindles, exposing {111} and {002} facets, showed the highest CO conversion (T50 = 69 and 74 °C, respectively), as well as a wide temperature window for total CO conversion (95-195 °C for spheres and 115-215 °C for spindles), in comparison with octahedrons, cubes and rods [116]. Interestingly, in different shaped ceria nanostructures, a close relationship is found between the concentration of oxygen vacancies and the amount of reduced copper species (Figure 17), clearly revealing the key role of exposed facets towards adjusting the catalytic performance. These findings were further substantiated by DFT calculations (Figure 18), showing the high population of oxygen vacancies at the intersection of {111} and {002} facets in opposition to CeO2 {111} surface [116].  In an attempt to optimize the CO-PROX performance through size and shape engineering singleand multi-shelled copper-ceria hollow microspheres were synthesized [260,269]. By tuning the number of shells, the catalytic activity was notably improved, with the triple-shelled structure ( Figure  19) exhibiting the highest activity and selectivity (100% CO conversion and 91% CO2 selectivity at 95 °C), as well as a wide temperature window for complete CO conversion (95-195 °C) [260]. The increase in the number of shells enhances the electronic and geometric interaction between copper and ceria, offering a high population of exposed active sites and an increased space inside the catalyst which facilitates reactants accessibility [260]. Taking into account the pivotal role of nanoparticles crystallite size/shape and their consequent effect on metal-support interactions, different preparation routes have been investigated for the synthesis of copper-ceria composites, such as the hydrothermal method, the template-assisted method, the solid-state preparation method, sol-gel, co-precipitation, freeze-drying, depositionprecipitation, etc. [250,251,[253][254][255]257,262,270]. For instance, template-assisted synthesis resulted in small ceria crystallite sizes (ca. 5.6 nm), and thus, in a high population of copper-ceria interfacial sites with implications in Cu oxidation state and CO-PROX activity [257]. Moreover, the precursor compounds or the template agent used during the synthesis procedure can affect the pore size and volume or the reducibility of the materials [255,271]. Interestingly, ethanol washing during the preparation of CuOx/CeO2 oxides leads to decreased particle sizes, as it affects the dehydration process between precursors particles, resulting in decreased adsorbed water and improved dispersion [272]. Very recently, a novel ultrasound-assisted precipitation method was employed to adjust the defective structure of CeO2 and in turn, the CO-RPOX activity [273]. By means of characterization techniques and theoretical calculations, it was shown that only two-electron defects on ceria surface (i.e., defects adsorbing oxygen to form peroxides instead of superoxide species which are formed on one-electron defects) were responsible for the formation of Cu + and Ce 3+ species, which were intimately involved in the CO adsorption and oxygen activation processes [273]. In particular, the adsorption of O2 on two-electron defects resulted in peroxides formation, followed by Cu ions incorporation towards the development of Cu-O-Ce structure. Meanwhile, the two additional electrons in the two-electron defects facilitate the electronic re-dispersion in Cu-O-Ce structure, leading to the creation of Cu + (CO adsorption sites) and Ce 3+ (oxygen activation sites).
Another approach in the direction of catalysts functionalization that has attracted considerable attention in recent years is the preparation of inverse catalytic systems. In particular, the co-existence of Cu + and Cu 2+ ions was observed in star-shaped inverse CeO2/CuOx catalysts which exhibited high catalytic activity [274]. Moreover, the alteration of Ce/Cu molar ratio and/or the pH value in the inverse CeO2/CuOx catalysts notably affects the morphology and the particle size, which in turn, favor the contact interface between ceria and copper, and thus, the CO oxidation at the expense of H2 oxidation in PROX process [44]. In addition, a multi-step synthetic approach has been applied for a high concentration of oxygen vacancies to be successfully anchored at the interfaces of the inverse CeO2/CuOx system, leading to outstanding CO-PROX activity (~100% CO conversion at a wide temperature window 120-210 °C) and adequate stability [275].
The doping effect on the CO-PROX performance has also been studied in the inverse copperceria catalysts [276,277]. It was reported that doping ceria with transition metals (e.g., Fe, Co, Ni) induces changes in the ceria lattice and in the formation of oxygen vacancies [276]. The doping element affects the reducibility of the CeO2/CuOx catalysts, while promoting the formation of Ce 3+ ions and oxygen vacancies, with the NiO-doped CeO2/CuOx catalyst exhibiting the highest activity (T50 = 68 °C) and the widest temperature window for total CO conversion (115-155 °C) [276]. In the inverse copper-ceria catalysts, it has also been found that the presence of Zn improves the CO-PROX performance, as it has the ability to hinder the CuO reduction to highly reduced copper sites which provide the active sites for the H2 oxidation [277].
By applying appropriate pretreatment protocols, the CO-PROX performance may also be greatly affected. In particular, the pretreatment of copper-ceria catalysts in an oxidative or reductive atmosphere affects the amount and dispersion of the active species, and consequently, the catalytic performance [262]. The pretreatment with hydrogen led to a breakage of the Cu-[Ox]-Ce structure, which resulted in enhanced catalytic performance, indicating the significance of the highly dispersed CuOx clusters in the CO-PROX process [262]. Furthermore, the pretreatment in an acidic or a basic environment affects the interaction between the two oxide phases. For instance, the pretreatment of ceria spheres in a basic solvent (2M NaOH), followed by etching in an ionic liquid for the acquisition of ceria nanocubes, resulted in the best catalytic activity at temperatures lower than 150 °C, due to the strong interaction between the highly dispersed CuOx clusters and ceria support [263]. An acidic treatment with nitric acid in nanorod-shaped CuOx/CeO2 catalysts has also been performed by Avgouropoulos and co-workers [264]. It was found that a highly acidic environment (pH < 4) led to an enrichment of catalysts surface in Cu + species and to high concentrations of oxygen vacancies and Ce 3+ species, while facilitating the formation of surface hydroxyls that are considered responsible for controlling the interfacial interactions in the copper-ceria binary system [264]. All the abovementioned characteristics in conjunction with the better copper dispersion and the improved reducibility of the highly acidic catalysts resulted in enhanced catalytic performance (T50 ≃ 84 °C) [264]. The same group has also investigated the pretreatment effect of employing ammonia solutions in copper-ceria nanorods [278]. It was revealed that the textural and structural properties of the modified catalysts remained almost unaffected after treatment, whereas, increasing the Cu:NH3 ratio to 1:4 resulted in higher reducibility and gave rise to Cu + and surface lattice oxygen species, leading, thus, to improved catalytic performance [278]. As shown in Figure 20, close relationships between the half-conversion temperature (T50) and the main Raman peak shift or the concentration of Ce 3+ and oxygen vacancies were observed [278]. Another adjusted parameter that can exert a profound influence on the catalytic performance is the electronic promotion mainly induced by alkali modifiers, as it may affect the chemisorption ability of active sites, as well as the copper-ceria interactions. In that context, it was found that the presence of K + ions in CuOx/CeO2 catalysts has a beneficial effect on CO-PROX process in the presence of both CO2 and H2O, since a proper K + content was proved to alleviate the CO2 and H2O adsorption on the reaction sites and thus, enhancing the catalytic performance [279]. Potassium has also been found to stabilize Cu + active species by affecting Cu-Ce interactions [280].
An additional engineering approach towards enhancing the CO-PROX reactivity of CuOx/CeO2 oxides involves the employment of chemical substances of specific architecture and textural properties, such as the carbon-based materials (rGO, CNTs, etc.). These materials favor the dispersion of copper and ceria, while affecting the reducibility and the population of oxygen vacancies, thus, resulting in enhanced catalytic performance at low-temperatures [256,[281][282][283][284]. As for example, the introduction of rGO resulted in abundant Ce 3+ species and oxygen vacancies, offering high catalytic activity at temperatures below 135 °C and good resistance to CO2 and H2O [283].
Interestingly, by combining electronic (alkali promotion) and chemical modification (carbon nanotubes), highly active multifunctional composites can be obtained. In copper-ceria catalysts supported on carbon nanotubes (CNTs) with a specific alkali/Cu atomic ratio, i.e., 0.68, the nature of the alkali metal (Li, Na, K, Cs) has been shown to affect the dispersion of ceria over CNTs and the copper-ceria interaction [261]. K-promoted CuOx/CeO2 oxides combined with CNTs exhibited high catalytic activity (T50 ≃ 109 °C as compared to 175 °C of un-promoted catalyst), attributed to the Kinduced modification on redox/electronic properties [261].

Water-Gas Shift Reaction (WGSR)
The water-gas shift reaction (WGSR) plays a key role in the production of pure hydrogen, through the chemical equilibrium: CO + H2O ↔ CO2 + H2. Among the different catalytic systems, copper-ceria oxides have gained particular attention, due to their low cost and adequate catalytic performance. Moreover, significant efforts have been put forward towards optimizing the lowtemperature WGS activity by means of the above discussed methodologies. Regarding CuOx/CeO2 catalyzed WGSR, two main reaction mechanisms have been proposed, namely, the redox and the associative mechanism. The first one involves the oxidation of adsorbed CO by oxygen originated by H2O dissociation. The second one involves the reaction of CO with surface hydroxyl groups towards the formation and subsequent decomposition of various intermediate species, such as formates [161,285].
A thorough study concerning the nature of active species and the role of copper-ceria interface for the low-temperature WGSR has been recently performed by Chen et al. [285]. It was revealed that the activity of copper-ceria catalysts is intrinsically related with the Cu + species present at the interfacial perimeter, with the CO molecule being adsorbed on the Cu + sites, while water being dissociatively activated on the oxygen vacancies of ceria [285,286]. In a similar manner, Flytzani-Stephanopoulos and co-workers [287] have earlier shown that strongly bound Cu-[Ox]-Ce species, probably associated with oxygen vacancies of ceria, are the active species for the low-temperature WGSR, whereas, the weakly bound copper oxide clusters and CuOx nanoparticles act as spectators.
Although the distinct role of copper and ceria and their interaction is not well determined, it is generally accepted that the activation of H2O, linked to copper-ceria interface and oxygen vacancies, is the rate-determining step [285]. Therefore, particular attention has been paid to modulate the interfacial reactivity via the above discussed adjusting approaches. Indicative studies towards modulating the WGSR performance are summarized in Table 4, and further discussed below. The preparation method can affect various characteristics, such as the specific surface area, the total pore volume, the dispersion of the active phase or the crystallite size [206,291]. For instance, copper-ceria catalyst prepared by a hard template method showed higher WGSR activity as compared to the one prepared by co-precipitation (62 vs. 54% CO conversion at 450 °C), due to its larger surface area and higher CuOx dispersion, while they both exhibited a similar amount of acidic surface sites [291]. Among CuOx/CeO2 catalysts synthesized by different precipitation methods, the catalysts prepared by stepwise precipitation showed the highest CO conversion, due to their higher reducibility and oxygen defects [208]. Precipitation was also found to give catalysts with higher WGSR activity, namely, 91.7% CO conversion at 200 °C, in comparison with the hydrothermal (82%) or sol-gel methods (64.5%), due to their abundance in oxygen vacancies, associated with the small CuOx crystals and large pore volume [206].
The precipitating agent used could also exert a significant impact on the physicochemical properties of CuOx/CeO2 catalysts, with the great implication in the catalytic behavior [207,292]. By employing ammonia water instead of ammonium and potassium carbonate, the WGSR activity is notably enhanced (91.7% CO conversion at 200 °C in contrast to 78.3% and 46.2%, respectively), due to the better dispersion of copper species and the stronger copper-ceria interactions [207]. Moreover, the copper precursor compound (nitrate or ammonium ions) and the preparation temperature can notably affect the WGSR activity [292].
Recently, it was found that the dispersion of differently formed copper structures (particles, clusters, layers) on ceria of rod-like morphology is dependent on copper loading, with low copper loadings (1-15 mol.%) exhibiting monolayers and/or bilayers of copper, while a further increase in copper loading up to 28 mol.% results in faceted copper particles and multi-layers of copper [286]. At copper loadings up to 15 mol.%, a linear relationship between the CO conversion and the copper content was observed (Figure 21), indicating that the number of the active interfacial sites (Cu + -Vo-Ce 3+ ) is significantly increased along with Cu content up to 15 mol.% [286]. The morphological features of both copper and ceria counterparts notably affect the WGSR activity. In a comprehensive study by Zhang et al. [293], it was reported that Cu cubes exhibit high WGSR activity in contrast to Cu octahedra with the Cu-Cu suboxide (CuxO, x ≥ 10) interface of Cu(100) surface being the active sites. In a similar manner, it was shown that ceria nanoshapes (rods, cubes, octahedra) exhibit different behavior during interaction with CO and H2O, due to their diverse defect chemistry [294]. Upon CO exposure, ceria nanocubes, exposing {100} planes, favor the formation of oxygen defects at the expense of the existing anti-Frenkel defects, while in nanorods and nanooctahedra (exposing mainly {111} planes) both types of defects are formed [294]. By combining Raman and FTIR results, it was revealed that H2-reduced ceria rods and octahedra could be further reduced in CO, resulting in the formation of both defects. In contrast, cubes cannot be further reduced by CO; thus, oxygen is available to form carbonates and bicarbonates by converting Frenkel defects to oxygen vacancies [294]. These findings clearly revealed the key role of both copper and ceria nanoshape on the defect chemistry of individual counterparts. It should be noted, however, that in the binary copper-ceria system, where multifaceted interactions are taking place, the relationships between shape effects and catalytic activity can be rather complex, leading to inconsistent conclusions [119,136,159].
Very recently, Yan et al. [288] reported on a novel structural design approach towards optimizing the WGS activity of CuOx/CeO2 system. In particular, inverse copper-ceria catalysts of high efficiency were developed through the fabrication of highly stable bulk-nano interfaces under reaction conditions. Nano-sized ceria particles (2-3 nm) were stabilized on bulk copper resulting in abundant ceria-copper interfaces [288]. This inverse catalyst showed outstanding WGS conversion (T100 = 350 °C), due to the high amount of interfacial sites and the strong copper-ceria interaction, which facilitated the dissociation of water and the oxidation of CO [288].
The doping approach has also been employed to enhance the WGSR activity of CuOx/CeO2 system [209,295]. For instance, copper-ceria catalysts doped with 2 wt.% yttrium have shown excellent WGSR activity and high thermal stability, as yttrium favored the oxygen vacancy formation on ceria [209]. Recently, Wang et al. [295] performed DFT calculations in order to theoretically investigate the alkali effect on the WGSR activity of Cu (111) and Cu (110) surfaces. It was found that potassium enhances the WGSR activity as it favors the dissociation of H2O and induces stronger promotion on the (111) surface. With regard to other alkali metals (Na, Rb, Cs), the promoting effect on the dissociation of water differentiates with their electronegativities which induce changes in the work function, i.e., the lower the work function, the stronger the promoting effect of the alkali [295].
Finally, the WGSR activity and the sintering resistance of the CuOx/CeO2 catalysts can be further enhanced by improving the metal-support interactions through appropriate pretreatment protocols [290,296]. As for example, the treatment of CuOx/CeO2 catalyst in a gas mixture of 20CO2/2H2 led to highly active catalysts, due to the electron enrichment of copper atoms via electronic metal-support interactions [290]. Moreover, ceria pretreatment in different atmosphere (air, vacuum or H2) affected the WGSR performance of CuOx/CeO2 catalysts, with the H2-pretreated samples exhibiting the highest conversion performance, due to the strong synergism between the two oxide phases, the small CuOx particle size, and the high concentration in oxygen vacancies [296].

CO2 Hydrogenation
The hydrogenation of carbon dioxide to value-added chemicals, such as methanol, has received considerable attention, in terms of environmental protection and sustainable energy. The significant role of copper-ceria interfacial sites in the CO2 hydrogenation process has been confirmed by both theoretical and experimental studies [40,297,298]. In particular, metal-oxide interface plays a key role in CO2 hydrogenation process, as it could provide the active sites for reactants adsorption, while these interfacial sites may stabilize the key intermediates [299]. In view of this fact, copper-ceria catalysts have shown higher selectivity in methanol than their zirconia-supported counterparts, as the copperceria interface favored the dispersion of copper and the oxygen vacancy formation, while the interaction between copper and ceria led to a decrease in copper particle size [300]. The interfaces between the defective CeO2-x and the highly dispersed Cu + /Cu 0 species are considered the active sites for methanol synthesis in the case of CuOx/CeO2 system [301]. Furthermore, the different metalsupport interactions between the two catalysts resulted in different reaction intermediates, namely, carbonates for the CuOx/CeO2 catalysts and bicarbonates for the zirconia-supported ones, thus, resulting in different selectivity, with the copper-zirconia composites being highly selective in CO [300].
In view of the above aspects, the fine-tuning of the metal-support interface could lead to highly active and selective catalysts. Indicative studies towards adjusting the CO2 conversion to methanol under similar reaction conditions are summarized in Table 5, and further discussed below. The activity and selectivity of the CuOx/CeO2 catalysts for methanol synthesis are greatly affected by the support morphology. Copper-ceria nanorods exposing {100} and {110} crystal planes exhibited the highest methanol yield (Table 5) as compared to nanocubes and nanoparticles, due to the strong interaction between the two oxide phases and the high copper dispersion [131]. Copperceria nanorods were also found to be more active than nanocubes, while exhibiting similar conversion performance with the nanoparticles, for carbonate (diethyl) hydrogenation [147].
In a similar manner, CuOx/CeO2 catalysts led, mainly, to the production of CO at atmospheric pressures through the RWGS reaction, with the nanorod-shaped catalyst exhibiting higher CO2 conversion (~50% at 450 °C) as compared to nanospheres (~40% at 450 °C), revealing the structure dependence of the RWGS [137]. The active intermediates are preferably formed on the {110} ceria exposed surface of the rod-like morphology, resulting in high catalytic performance [137].
Copper-ceria nanorods of various copper loadings were also investigated in the hydrogenation of carbonate to methanol, with the catalysts of ca. 20 wt.% Cu content exhibiting superior catalytic performance [306]. The copper content can significantly affect the mole fraction of Ce 3+ and Cu + species (Figure 22), and in turn, the methanol yield [306]. In addition, a space-confined synthetic approach was applied for the synthesis of highly dispersed copper-ceria catalysts for RWGS, offering 100% CO selectivity at 300 °C and ambient pressure [307]. The enhanced catalytic performance was ascribed to the abundance in interfaces formed among the highly dispersed copper nanoparticles and the Ce 3+ species, thus, favoring H2 spillover [307].
The controlled synthesis of multicomponent systems could also be an effective approach for highly active and selective hydrogenation catalysts (e.g., [302][303][304][305]308]). For instance, the ternary composite consisting of Cu, ZnO, CeOx, supported on SBA-15 exhibited high catalytic activity for methanol synthesis (Table 5), due to the peculiar synergistic effects between the different counterparts [302]. Copper was considered to be the active site for hydrogen activation, while ZnO and CeOx oxides facilitated the CO2 adsorption and hydrogen spillover on the interfacial sites [302]. In a similar manner, the introduction of alumina to ceria carrier (Cu/AlCe) led to highly active composites (Table 5), mainly ascribed to the high copper dispersion [303]. Interestingly, highly active and selective CO2 hydrogenation catalysts can be obtained by co-adjusting the composition, structure and shape, in line with the fine-tuning methodology herein proposed (Figures 2 and 3). In this perspective, bimetallic composites (Cu-Ni) incorporated into ceria nanoparticles of specific morphology (e.g., nanotubes, nanorods) could lead to highly active composites for the CO2 hydrogenation to methanol ( Table 5). The enhanced catalytic performance of Cu-Ni/CeO2 nanoshaped catalysts was mainly interpreted on the basis of the synergistic interaction between Cu and Ni as well as of that between the ceria carrier and Cu-Ni alloy [304,305]. Similarly, the bimetallic Cu-Fe/CeO2 catalyst has shown enhanced stability in the high-temperature RWGS due mainly to the fact that iron oxide clusters (FeOx) highly dispersed over ceria act as textural promoters [308]. Finally, copper nanocrystals encapsulated in Zr-based MOFs demonstrated high activity and selectivity for CO2 hydrogenation to methanol, outperforming the benchmark Cu/ZnO/Al2O3 catalyst [197].

Outlook and Challenges
In the present review, the copper-ceria binary system has been employed as a reference system to reveal the different approaches that can be followed to modulate the local surface chemistry, and in turn, the catalytic performance of metal oxides (MOs), by means of size, shape and electronic/chemical functionalization. More importantly, the fine-tuning of the above-mentioned parameters can affect not only the reactivity of metal sites in its own right, but also the interfacial activity (e.g., through the formation of oxygen vacancies, facilitation of redox interplay between the different counterparts, etc.) offering a synergistic contribution towards the development of NMs-free highly active and selective composites for several energy and environmental applications.
For instance, the employment of appropriate synthetic routes, such as the hydrothermal method, leads to the development of nanoparticles with specific morphologies, exposing distinct crystal facets of different coordination environments, with great implications in catalysis. Moreover, particles size/shape engineering strongly affects the interfacial reactivity through both geometric and electronic interactions, offering metal oxide systems with the desired properties. In addition, special pretreatment protocols or activation procedures can notably affect the metal dispersion and the population of oxygen defects, with great consequences in the catalytic efficiency. In view of the above, the fine tuning of metal oxides by combining bulk and nano effects or by adjusting the coordination environment could lead to highly efficient catalysts.
Besides the modulation of local surface chemistry by means of size and shape engineering, the electronic/chemical modification (e.g., alkali promotion, incorporation of rGO or g-C3N4, employment of MOFs) can be adopted as an additional functionalization tool to regulate the electronic environment and the oxygen exchange kinetics of MOs.
In view of the above aspects, highly active composites, with a comparable or even better performance than that of NMs, have been developed for various processes, such as CO oxidation, N2O decomposition, preferential oxidation of CO, among others. As for example, the combination of precipitation method with alkali promotion can lead to highly active and oxygen-tolerant CuOx/CeO2 catalysts for N2O decomposition. On the other hand, the modulation of ceria support morphology (nanorods) by the hydrothermal method resulted in CuOx/CeO2 composites with superior CO oxidation performance, even better to that of Pt-based catalysts. More importantly, the co-adjustment of different parameters (e.g., the shape of individual counterparts along with the electronic state of metal entities) could lead not only to distinct reactivity of each counterpart, but also to different synergistic interactions, offering mixed metal oxides of unique features. Hence, metal oxides appropriately adjusted by means of suitable synthetic and electronic/chemical modification routes could provide the materials platform for real-life energy and environmental applications.
Another approach towards the fine-tuning of metal oxides could be the employment of computational studies (e.g., DFT calculations) prior to the synthesis of the catalysts, providing, thus, the required feedback that would lead to the focused functionalization of specific parameters. This combinatorial theoretical and experimental approach could result in specific composites with predefined characteristics, while it would save precious time during experimental trials.
Last, but not least, the conclusions drawn from the present survey can provide the design principles for the development of low-loading NMs-based catalysts, paving the way for the decrease of noble metals content in energy and environmental applications in which their use is inevitable. In any case, the fundamental understanding of structure-property relationships is a prerequisite factor towards the rational design of efficient and inexpensive catalytic composites.
Author Contributions: M.L. contributed to paper writing; M.K. contributed to the conception, design and writing of the paper; All authors contributed to the discussion, read and approved the final version of the manuscript. All authors have read and agreed to the published version of the manuscript.