Polyoxometalate Template-Based Synthetic Strategy to Prepare Ni, Mo Co-Doped CdS for E ﬃ cient Photocatalytic Hydrogen Evolution from Water Splitting

: In this work, a novel polyoxometalate template-based strategy was applied to construct the bi-metal-doped CdS photocatalysts. NiMo 6 polyoxometalate template precursor was applied for the preparation of Ni, Mo co-doped CdS photocatalysts (NiMo-CdS). The structures of the materials were explored by XRD, SEM, HRTEM, HAADF, element mapping, XPS, Raman spectrum and UV-vis DRS. Moreover, the results of the UV-vis spectrum showed that NiMo-CdS exhibited an enhanced performance on light absorption. The results of photocatalytic hydrogen evolution from water splitting demonstrated that the NiMo-CdS showed higher e ﬃ ciency on hydrogen evolution than noble-metal Pt-doped CdS. The reason could be ascribed to the enhanced light absorption ability and charge separation after Ni and Mo were introduced, which could also act as co-catalysts. The apparent quantum yield (AQY) e ﬃ ciency could reach 42% at 365 nm. This work proposed a novel and inexpensive method to synthesize the bi-metal (Ni, Mo) decorated CdS photocatalysts for e ﬃ cient hydrogen evolution from water splitting.


Introduction
Photocatalytic water splitting has been proposed since Honda and Fujishima first reported it in 1972 [1]. Afterward, it ignited a majority of interests in photocatalytic water splitting for hydrogen production. Past decades have witnessed the development of photocatalysis on the materials and the intrinsic mechanisms [2][3][4][5]. Among them, TiO 2 was regarded as one of the most traditional materials [6][7][8]. However, the limitations constrained its application since it could only absorb the UV-light that occupied only 4% of the full arc solar spectrum. Furthermore, the low carrier mobility also makes efficiency lower than 1%. Therefore, it was urgent to explore the novel materials which could absorb the irradiation light from a wide range, like visible light, or even infrared light.

Results and Discussions
The powder X-ray diffraction (XRD) patterns of x%(NiMo 6 )@CdS-τ (x = 5, 7.5, 10, τ = 12, 24, 36 h) composites are shown in Figure 1a-f, respectively. Although, after modification with variable amounts of NiMo 6 precursor and variable hydrothermal time, all XRD patterns turned out to be similar and all peaks of pristine CdS could be obviously detected in Figure 1a,c,e, according to Jade card No.01-0783. It implies that the introduction of Ni and Mo shows little influence on the bulk CdS structure. Despite this, Ni, Mo co-doping increases the lattice constant of the CdS structure, resulting in a small peak shift towards a lower angle, as shown in Figure 1b,d,f. Nonetheless, the crystalline structure of Ni and Mo species was still uncertain from the above XRD patterns, and hereafter, identified by X-ray photoelectron spectrum (XPS) measurements that will be discussed later.
The morphology characterizations of x%(NiMo 6 )@CdS-24 h were investigated by scanning electron microscopy (SEM) and high-resolution transmission electron microscopy (HRTEM) as depicted in Figures 2a-i and 3a-g, respectively. It can be seen in Figure 2 that polyhedral CdS particles exposing terrace facets on the corners were decorated with stacked thin slices. Comparing Figure 2a,d,g, the average crystal size of CdS, which was estimated from SEM images, exhibited a decreasing trend with the increasing hydrothermal time. In Figures 3 and 4a,b, a detailed understanding of crystal structure and morphology was provided by HRTEM measurements equipped with bright field (BF) and high-angle annular dark-field (HAADF) modes. As illustrated in Figure 3a-c, bulk polyhedral CdS particles were loaded with stacked structures that were speculated as NiO/MoS 2 layers according to Reference [10]. Furthermore, in Figure 3d,e, two specified areas highlighted by the square were targeted at the stacked layers ( Figure 3g) and the interfacial region (Figure 3f), respectively. More specifically, the lattice distances in these two regions were measured. In the interfacial region (red square box 1),  Figure 3f. The amplified HRTEM image of the stacked structure (yellow square box 2) in Figure 3g showed the coexistence of 0.210 and 0.940 nm spacing lattice fringes [25], which were referred to as NiO and 1T-MoS 2 , respectively. Through the identification of lattice constant in amplified HRTEM images, a preliminary conclusion that the composite of 1T-MoS 2 doping with NiO was decorated as the layer structure on bulk CdS particle has been raised so far. Moreover, the chemical composition and element distribution of stacked structures were further determined by element mapping. It is worth noting in Figure 4 that the stacked structures marked in a circle were mainly composed of Mo and S elements, whereas no Cd element was found. Besides, the Ni element was also observed in the red circle and bulk particle simultaneously, which can be considered that Ni atoms dope in MoS 2 and bulk CdS particle with a uniform distribution. The HRTEM mapping results also supported the speculation of NiO/1T-MoS 2 structure. on the surface of CdS, which could enhance the photocatalytic performance [22][23][24]. Afterward, the 1T and 2H mixed phase of MoS2 coupled with CdS as the photocatalyst also was synthesized [11]. The results exhibited an excellent activity on photocatalytic hydrogen evolution. However, suppose that the Ni-based co-catalysts and 1T-MoS2 with a higher concentration could serve as the co-catalysts simultaneously, it will be favorable for the enhancement of the charge separation and light absorption and thus, improve the photocatalytic activity.
Recently, Huang et al. has presented a novel method to stabilize the 1T-MoS2, which gained an ascendant performance in electrochemical hydrogen evolution [10]. In this work, the polyoxometalate was used as a template to synthesize the NiO/1T-MoS2 composites. If this synthetic strategy could be applied in the construction of photocatalysts, the Ni, Mo co-doped CdS could be fulfilled via a simple method. However, relative works were rare. Consequently, in this work, NiO/1T-MoS2 as a co-catalyst was prepared via the polyoxometalate template-based method in onestep. The results exhibited that the MoS2 was mainly composed of the 1T phase and thus the photocatalytic ability was evidently improved. The AQY efficiency could reach 42% at under 365 nm. This work proposed a novel method for the construction of co-catalysts with non-noble metal in particulate photocatalytic water splitting, especially for the 1T-MoS2 preparation strategy.

Results and Discussions
The powder X-ray diffraction (XRD) patterns of x%(NiMo6)@CdS-τ (x = 5, 7.5, 10, τ = 12, 24, 36 h) composites are shown in Figure 1a-f, respectively. Although, after modification with variable amounts of NiMo6 precursor and variable hydrothermal time, all XRD patterns turned out to be similar and all peaks of pristine CdS could be obviously detected in Figure 1a,c,e, according to Jade card No.01-0783. It implies that the introduction of Ni and Mo shows little influence on the bulk CdS structure. Despite this, Ni, Mo co-doping increases the lattice constant of the CdS structure, resulting in a small peak shift towards a lower angle, as shown in Figure 1b,d,f. Nonetheless, the crystalline structure of Ni and Mo species was still uncertain from the above XRD patterns, and hereafter, identified by X-ray photoelectron spectrum (XPS) measurements that will be discussed later. The morphology characterizations of x%(NiMo6)@CdS-24 h were investigated by scanning electron microscopy (SEM) and high-resolution transmission electron microscopy (HRTEM) as depicted in Figure 2a-i and Figure 3a-g, respectively. It can be seen in Figure 2 that polyhedral CdS particles exposing terrace facets on the corners were decorated with stacked thin slices. Comparing Figure 2a,d,g, the average crystal size of CdS, which was estimated from SEM images, exhibited a decreasing trend with the increasing hydrothermal time. In Figures 3 and 4a,b, a detailed understanding of crystal structure and morphology was provided by HRTEM measurements equipped with bright field (BF) and high-angle annular dark-field (HAADF) modes. As illustrated in were further determined by element mapping. It is worth noting in Figure 4 that the stacked structures marked in a circle were mainly composed of Mo and S elements, whereas no Cd element was found. Besides, the Ni element was also observed in the red circle and bulk particle simultaneously, which can be considered that Ni atoms dope in MoS2 and bulk CdS particle with a uniform distribution. The HRTEM mapping results also supported the speculation of NiO/1T-MoS2 structure.  structures marked in a circle were mainly composed of Mo and S elements, whereas no Cd element was found. Besides, the Ni element was also observed in the red circle and bulk particle simultaneously, which can be considered that Ni atoms dope in MoS2 and bulk CdS particle with a uniform distribution. The HRTEM mapping results also supported the speculation of NiO/1T-MoS2 structure.    For the purpose of unveiling the definite crystalline structure of NiMo-containing stacks on the CdS surface, the 5%(NiMo6)@CdS-24 h sample was probed by X-ray photoelectron spectrum (XPS) measurements. As indicated in Figure 5a, two characteristic signals referred to as Cd 2+ 3d5/2 and Cd 2+ 3d3/2, of which binding energy was located at 404.8 and 411.5 eV respectively, both exhibited a 0.2 eV blueshift in comparison with pure CdS [9,18,26]. The S 2p spectrum in Figure 5b was deconvolved into three characteristic peaks appearing at 161.2, 162.5 and 164.5 eV, which can be assigned to S 2-2p3/2, S 2-2p1/2 [9,18,27] and S2 2- [28], respectively. Similarly, compared with pure CdS, these peaks in the S 2p spectrum showed a slight blueshift ranging from 0.1 to 0.4 eV. The blue shift of Cd 3d and S 2p spectrum resulted from the decoration of NiMo-containing composite that slightly changed the chemical state of bulk CdS.
The Mo 3d spectrum in Figure 5c was characterized by three main peaks referred to as Mo 4+ 3d5/2, Mo 4+ 3d3/2 and Mo 6+ , implying the existence of Mo 4+ species in (NiMo6)@CdS. Furthermore, the peaks of Mo 4+ 3d5/2 and Mo 4+ 3d3/2 appeared at 229.0 and 232.3 eV respectively, which were in accordance with bare 1T-MoS2 published in previous reports [9,18] and no additional Mo 4+ signal was observed. That said, it is 1T-MoS2 rather than 2H-MoS2 or other Mo-containing compounds that were modified on bulk CdS particles, exactly falling in line with the anticipation through this template-based synthetic strategy.
On the contrary, according to our group's previous work [11], 1T and 2H phases of MoS2 can coexist as the mixed-phase in MoS2@CdS composites. It seems to inevitably generate a mixed phase of MoS2 while modifying CdS photocatalyst [9,26]. By contrast, the above observation of pure 1T-MoS2 phase could be ascribed to the dopant Ni, which might facilitate the transformation from the coexistence of 1T-and 2H-MoS2 to a mere 1T-MoS2 phase. According to the previous study, NiMo6 precursor was introduced as the template to fabricate the NiO/1T-MoS2 composite structure that was decorated on CdS particles, where 1T-MoS2 was stabilized by NiO species [10]. Meanwhile, due to the n-type doping, Mo atoms donate electrons to Ni atoms (n-type dopants) and act as the positive charge centers, resulting in the upshift in Mo 3d spectrum, as same to the similar upshift in Cd 3d For the purpose of unveiling the definite crystalline structure of NiMo-containing stacks on the CdS surface, the 5%(NiMo 6 )@CdS-24 h sample was probed by X-ray photoelectron spectrum (XPS) measurements. As indicated in Figure 5a, two characteristic signals referred to as Cd 2+ 3d 5/2 and Cd 2+ 3d 3/2 , of which binding energy was located at 404.8 and 411.5 eV respectively, both exhibited a 0.2 eV blueshift in comparison with pure CdS [9,18,26]. The S 2p spectrum in Figure 5b was deconvolved into three characteristic peaks appearing at 161.2, 162.5 and 164.5 eV, which can be assigned to S 2− 2p 3/2 , S 2− 2p 1/2 [9,18,27] and S 2 2− [28], respectively. Similarly, compared with pure CdS, these peaks in the S 2p spectrum showed a slight blueshift ranging from 0.1 to 0.4 eV. The blue shift of Cd 3d and S 2p spectrum resulted from the decoration of NiMo-containing composite that slightly changed the chemical state of bulk CdS. The Mo 3d spectrum in Figure 5c was characterized by three main peaks referred to as Mo 4+ 3d 5/2 , Mo 4+ 3d 3/2 and Mo 6+ , implying the existence of Mo 4+ species in (NiMo 6 )@CdS. Furthermore, the peaks of Mo 4+ 3d 5/2 and Mo 4+ 3d 3/2 appeared at 229.0 and 232.3 eV respectively, which were in accordance with bare 1T-MoS 2 published in previous reports [9,18] and no additional Mo 4+ signal was observed. That said, it is 1T-MoS 2 rather than 2H-MoS 2 or other Mo-containing compounds that were modified on bulk CdS particles, exactly falling in line with the anticipation through this template-based synthetic strategy.
On the contrary, according to our group's previous work [11], 1T and 2H phases of MoS 2 can coexist as the mixed-phase in MoS 2 @CdS composites. It seems to inevitably generate a mixed phase of MoS 2 while modifying CdS photocatalyst [9,26]. By contrast, the above observation of pure 1T-MoS 2 phase could be ascribed to the dopant Ni, which might facilitate the transformation from the coexistence of 1T-and 2H-MoS 2 to a mere 1T-MoS 2 phase. According to the previous study, NiMo 6 precursor was introduced as the template to fabricate the NiO/1T-MoS 2 composite structure that was decorated on CdS particles, where 1T-MoS 2 was stabilized by NiO species [10]. Meanwhile, due to the n-type doping, Mo atoms donate electrons to Ni atoms (n-type dopants) and act as the positive charge centers, resulting in the upshift in Mo 3d spectrum, as same to the similar upshift in Cd 3d spectrum. Besides, the appearance of Mo 6+ species can be attributed to partial oxidation of Mo 4+ in the synthesis procedure [10,18,29]. The above findings indicate an intriguing possibility that NiO/1T-MoS 2 @CdS photocatalysts were successfully prepared by the introduction of NiMo 6 precursors into the CdS photocatalyst.
MoS2@CdS photocatalysts were successfully prepared by the introduction of NiMo6 precursors into the CdS photocatalyst.
Raman spectra were conducted to obtain further insight into the phase of MoS2 on the surface of CdS. As illustrated in Figure 5d, two intensive peaks of the Raman shift which appeared at 152.4 and 218.2 cm −1 [30] were detected, respectively. It further substantiates the existence of the 1T-MoS2 phase, whereas no observation of the 2H-MoS2 phase was found. It keeps in agreement with the XPS analysis discussed above. Surprisingly no obvious peak referred to 1T-MoS2 was observed in 10%(NiMo6)@CdS sample, which inferred that 1T-MoS2 was almost covered by excess NiO once the amount of NiMo6 precursor increased over 10%. As the first step of the three main steps in photocatalysis, the optical absorption of photocatalysts is of necessity to enhance photocatalytic performance [31], which can be reflected by UV-vis diffuse reflection spectrum (UV-vis DRS). As illustrated in Figure 6a, pure CdS and 10%(NiMo6)@CdS-24 h samples had an approximate band edge position at nearly 515 and 555 nm, respectively. The absorption band edge positions of 5% and 7.5%(NiMo6)@CdS-24 h samples were at around 540 nm. According to the Tauc plot method, the band gap of semiconductor catalysts was calculated. As presented in Figure 6b, the 10%(NiMo6)@CdS-24 h sample had a band gap at around 2.24 eV, which was narrower than 5% (2.32 eV), 7.5%(NiMo6)@CdS-24 h samples (2.28 eV) and pure CdS (2.40 eV). Moreover, the light absorption ability of 5%(NiMo6)@CdS-24 h composite was superior to the pristine Raman spectra were conducted to obtain further insight into the phase of MoS 2 on the surface of CdS. As illustrated in Figure 5d, two intensive peaks of the Raman shift which appeared at 152.4 and 218.2 cm −1 [30] were detected, respectively. It further substantiates the existence of the 1T-MoS 2 phase, whereas no observation of the 2H-MoS 2 phase was found. It keeps in agreement with the XPS analysis discussed above. Surprisingly no obvious peak referred to 1T-MoS 2 was observed in 10%(NiMo 6 )@CdS sample, which inferred that 1T-MoS 2 was almost covered by excess NiO once the amount of NiMo 6 precursor increased over 10%.
As the first step of the three main steps in photocatalysis, the optical absorption of photocatalysts is of necessity to enhance photocatalytic performance [31], which can be reflected by UV-vis diffuse reflection spectrum (UV-vis DRS). As illustrated in Figure 6a, pure CdS and 10%(NiMo 6 )@CdS-24 h samples had an approximate band edge position at nearly 515 and 555 nm, respectively. The absorption band edge positions of 5% and 7.5%(NiMo 6 )@CdS-24 h samples were at around 540 nm. According to the Tauc plot method, the band gap of semiconductor catalysts was calculated. As presented in Figure 6b, the 10%(NiMo 6 )@CdS-24 h sample had a band gap at around 2.24 eV, which was narrower than 5% (2.32 eV), 7.5%(NiMo 6 )@CdS-24 h samples (2.28 eV) and pure CdS (2.40 eV). Moreover, the light absorption ability of 5%(NiMo 6 )@CdS-24 h composite was superior to the pristine CdS photocatalyst and NiMo 6 precursor in Figure 6c,d. Therefore, the modification with NiO/1T-MoS 2 on bulk CdS photocatalyst broadened the absorption of the light wavelength range [27,32]. The enhancement of absorption ability can be attributed to the heterojunction among NiO, 1T-MoS 2 and CdS [32,33]. Additionally, the tailing region of light absorption was intensified, which could be ascribed to the increasing amount of MoS 2 with a broad absorption range in visible light [34,35].
Catalysts 2020, 10, x FOR PEER REVIEW 7 of 13 CdS photocatalyst and NiMo6 precursor in Figure 6c,d. Therefore, the modification with NiO/1T-MoS2 on bulk CdS photocatalyst broadened the absorption of the light wavelength range [27,32]. The enhancement of absorption ability can be attributed to the heterojunction among NiO, 1T-MoS2 and CdS [32,33]. Additionally, the tailing region of light absorption was intensified, which could be ascribed to the increasing amount of MoS2 with a broad absorption range in visible light [34,35]. Accumulated hydrogen evolution of x%(NiMo6)@CdS-τ samples was recorded as illustrated in Figure 7a-f. Typically, loading noble metal Pt as a co-catalyst on CdS photocatalyst enhances the photocatalytic performance. As shown in Figure 7e, (NiMo6)@CdS samples with non-noble metal all displayed a remarkable improvement in photocatalytic activity, which was comparable or even superior to the optimal Pt-CdS in the literature [36]. With regard to the hydrothermal time, τ, in Figure 7b-d, the (NiMo6)@CdS-24 h sample was endowed with the best photocatalytic performance. It infers that the (NiMo6)@CdS-24 h sample was prepared in suitable particle size and modified with a uniform distribution of NiO/1T-MoS2 after moderate hydrothermal time of 24 h, which accounts for its outstanding activity compared with the other hydrothermal times. Furthermore, as we can see in Figure 7a, the 5%(NiMo6)@CdS sample exhibited the highest photocatalytic activity with a hydrogen evolution rate of 348.5 μmol/h, whereas 7.5% and 10%(NiMo6)@CdS samples showed a relatively lower rate of 301.1 and 253.7 μmol/h, under the same hydrothermal time of 24 h. This difference of photocatalytic performance between variable precursor amounts can be explained by the influence of the modification with the special layer structure of NiO/1T-MoS2, which is clarified as mentioned below. Additionally, combined with the analysis of optical absorption, Figure 7f showed that the 5%(NiMo6)@CdS sample performed an excellent photocatalytic activity within the visible light region. Photocatalytic stability was evaluated by intermittent test sequences and each sequence consisted of the consecutive hydrogen measurement for 5 h. After one test sequence, the Accumulated hydrogen evolution of x%(NiMo 6 )@CdS-τ samples was recorded as illustrated in Figure 7a-f. Typically, loading noble metal Pt as a co-catalyst on CdS photocatalyst enhances the photocatalytic performance. As shown in Figure 7e, (NiMo 6 )@CdS samples with non-noble metal all displayed a remarkable improvement in photocatalytic activity, which was comparable or even superior to the optimal Pt-CdS in the literature [36]. With regard to the hydrothermal time, τ, in Figure 7b-d, the (NiMo 6 )@CdS-24 h sample was endowed with the best photocatalytic performance. It infers that the (NiMo 6 )@CdS-24 h sample was prepared in suitable particle size and modified with a uniform distribution of NiO/1T-MoS 2 after moderate hydrothermal time of 24 h, which accounts for its outstanding activity compared with the other hydrothermal times. Furthermore, as we can see in Figure 7a, the 5%(NiMo 6 )@CdS sample exhibited the highest photocatalytic activity with a hydrogen evolution rate of 348.5 µmol/h, whereas 7.5% and 10%(NiMo 6 )@CdS samples showed a relatively lower rate of 301.1 and 253.7 µmol/h, under the same hydrothermal time of 24 h. This difference of photocatalytic performance between variable precursor amounts can be explained by the influence of the modification with the special layer structure of NiO/1T-MoS 2 , which is clarified as mentioned below. Additionally, combined with the analysis of optical absorption, Figure 7f showed that the 5%(NiMo 6 )@CdS sample performed an excellent photocatalytic activity within the visible light region. Photocatalytic stability was evaluated by intermittent test sequences and each sequence consisted of the consecutive hydrogen measurement for 5 h. After one test sequence, the photocatalysts were reused through suction filtration and drying in a vacuum. Then, the photocatalytic reactor with photocatalysts inside was evacuated again and then irradiated for the next round. As illustrated Catalysts 2020, 10, 1478 8 of 13 in Figure 8a, the 5%(NiMo 6 )@CdS-24 h composite maintained a relatively stable photocatalytic performance through three cycles. In the last stability test cycle, the average hydrogen evolution per hour had decreased to approximately 90% compared to the initial cycle. In Figure 8b, the XRD pattern of the after-test sample was conducted in comparison with the before-test one. As illustrated in Figure 8b, there was no obvious difference in the characteristic peaks, which indicated that the photo-corrosion phenomenon was not observed from the XRD result and the main structure of CdS was maintained. Therefore, the photocatalytic performance reduction can be attributed to the mass loss of photocatalysts in the suction filtration and drying process. As mentioned above, the introduction of NiO species could stabilize the 1T-MoS 2 structure, which could probably result in the stable photocatalytic activity of NiMo-CdS samples. However, the intrinsic stabilization mechanism of NiMo-CdS photocatalysts needs to be further explored in future research.
Catalysts 2020, 10, x FOR PEER REVIEW 8 of 13 photocatalysts were reused through suction filtration and drying in a vacuum. Then, the photocatalytic reactor with photocatalysts inside was evacuated again and then irradiated for the next round. As illustrated in Figure 8a, the 5%(NiMo6)@CdS-24 h composite maintained a relatively stable photocatalytic performance through three cycles. In the last stability test cycle, the average hydrogen evolution per hour had decreased to approximately 90% compared to the initial cycle. In Figure 8b, the XRD pattern of the after-test sample was conducted in comparison with the before-test one. As illustrated in Figure 8b, there was no obvious difference in the characteristic peaks, which indicated that the photo-corrosion phenomenon was not observed from the XRD result and the main structure of CdS was maintained. Therefore, the photocatalytic performance reduction can be attributed to the mass loss of photocatalysts in the suction filtration and drying process. As mentioned above, the introduction of NiO species could stabilize the 1T-MoS2 structure, which could probably result in the stable photocatalytic activity of NiMo-CdS samples. However, the intrinsic stabilization mechanism of NiMo-CdS photocatalysts needs to be further explored in future research. distributed uniformly on the surface of both CdS particles and 1T-MoS2 layers, exhibit high activity in proton reduction [22,24]. Therefore, NiO and 1T-MoS2 loaded as bi-metal co-catalysts both play a vital role in promoting proton reduction, ultimately accelerating the hydrogen evolution. Having said that, the substantial interaction between NiO/1T-MoS2 with bulk CdS need to be further investigated with in-depth studies, and the migration mechanism of photo-induced electrons inside NiO/1T-MoS2 layers have not yet been fully clarified.

Materials
All chemicals were obtained as analytic reagent chemicals unless otherwise noted. Ammonium molybdate tetrahydrate ((NH4)6Mo7O24·4H2O), nickel nitrate hexahydrate (Ni(NO3)2·6H2O) and cadmium nitrate tetrahydrate (Cd(NO3)2·4H2O) were bought from Beijing InnoChem technology Co., Ltd. (Beijing, China). Thioacetamide (CH3CSNH2) was purchased from Sinopharm Chemical Reagent Co., Ltd. (Beijing, China). Ultra-pure water with a resistivity of 18.2 MΩ·cm was used throughout all of the experiments. The influence mechanism of the modification with NiO/1T-MoS 2 on pristine CdS photocatalyst can be elucidated from two primary perspectives. Through the polyoxometalate template-based synthetic strategy with NiMo 6 precursor [10], NiO/1T-MoS 2 was successfully loaded on the bulk CdS surface and stacked together to eventually form the thick layer structures. On the one hand, due to the superior absorption ability of 1T-MoS 2 [33][34][35], the thicker layer structure containing more NiO/1T-MoS 2 can absorb a larger proportion of the incident light, which in turn suppresses the excitation of photo-induced electron and hole pairs inside CdS photocatalysts and further diminishes the total photocatalytic efficiency of the NiO/1T-MoS 2 @CdS composite. In other words, the excessive coverage of NiO/1T-MoS 2 restrains the optical absorption of bulk CdS photocatalyst and hence the total photocatalytic performance is bound to reduce to some extent. On the other side, the effective photocatalysis reacts in the prerequisite that the photo-excited carriers separated inside the bulk CdS particle successfully transfer to the surface of Ni/1T-MoS 2 layer structures, where the interfacial chemical reaction occurs. It is reasonable to speculate that the 1T-MoS 2 layer structure as its excellent conductivity [37,38] enhances the transportation of electrons through its suitable layer structure and simultaneously inhibits the combination of photo-excited charges in CdS particles. NiO species, distributed uniformly on the surface of both CdS particles and 1T-MoS 2 layers, exhibit high activity in proton reduction [22,24]. Therefore, NiO and 1T-MoS 2 loaded as bi-metal co-catalysts both play a vital role in promoting proton reduction, ultimately accelerating the hydrogen evolution. Having said that, the substantial interaction between NiO/1T-MoS 2 with bulk CdS need to be further investigated with in-depth studies, and the migration mechanism of photo-induced electrons inside NiO/1T-MoS 2 layers have not yet been fully clarified.

Materials
All chemicals were obtained as analytic reagent chemicals unless otherwise noted. Ammonium molybdate tetrahydrate ((NH 4 ) 6 [10]. 4.2 mmol of (NH 4 ) 6 Mo 7 O 24 ·4H 2 O was dissolved in 80 mL ultra-pure water and the solution was heated to 80 • C and then stirred for 1 h, which was referred to as Mo-Solution. 4 mmol of Ni(NO) 3 ·6H 2 O was dissolved in 20 mL ultra-pure water, which was referred to as Ni-Solution. Next, the latter Ni-Solution was added dropwise to the former Mo-Solution and was stirred for 5 h at 80 • C. Subsequently, 80 mL ultra-pure water was added, after which the solution was heated to 100 • C and stirred for 1 h. Finally, after the solution was naturally cooled down to room temperature, the obtained NiMo 6 products were washed several times by centrifugation with distilled water and dried at 80 • C for 12 h under vacuum.
3.3. Synthesis of x%(NiMo 6 )@CdS-τ(τ = 12, 24, 36 h) (NiMo 6 )@CdS particles with variable amounts of NiMo 6 were fabricated by a conventional hydrothermal reaction method. 36 mmol of CH 3 CSNH 2 was dissolved into 50 mL ultra-pure water and the solution was sonicated for 5 min. After sonication, the solution was stirred for 1 h. Then, 5 mmol of Cd(NO 3 ) 2 ·4H 2 O and variable amounts of NiMo 6 precursor (x% × 5 mmol NiMo 6 ) were introduced into the CH 3 CSNH 2 aqueous solution, respectively. After continuous magnetic stirring for 6 h, the thorough stirring solution was transferred into a 100 mL Teflon-lined stainless-steel autoclave and heated at 200 • C for periods ranging from 12 to 36 h. After being washed 5~6 times by centrifugation with distilled water and dried at 80 • C for 12 h under vacuum, the brownish-yellow x%(NiMo 6 )@CdS-τ products were obtained, where x and τ represent the mole fraction of NiMo 6 precursor and hydrothermal time, respectively.

Synthesis of Pt-CdS
Pt-CdS photocatalyst was prepared by the photo-deposition method. Typically, with H 2 PtCl 6 as a precursor, the co-catalyst Pt with a mass ratio of 0.2% compared to the samples, was loaded on pure CdS photocatalyst via the photo-deposition method, in the presence of 80 mL of methanol solution (25 vol%). After the suction filtration, all solid samples were dried at 80 • C for 12 h in a vacuum and then the Pt-CdS photocatalyst was collected and obtained as the experimental control group.

Characterizations
To identify the crystalline phase and the composition of the obtained photocatalysts, powder X-ray diffraction patterns were measured on an X-ray diffractometer (D8 Advance, Bruker, Karlsruhe, Germany) equipped with Cu-Kα as the X-ray source at 40 kV voltage and 15 mA current. The diffraction angle (2θ) range was from 10 • to 80 • with a scan speed of 5 • /min. The powder X-ray diffraction patterns were further analyzed by Jade 6.0 software. The surface morphology of obtained photocatalysts was unveiled by scanning electron microscopy (SEM) (JSM-6700, JEOL, Tokyo, Japan) and high-resolution field-emission transmission electron microscopy (HRTEM) with element mapping (TALOS F200X, FEI, Hillsborough, OR, USA). The chemical composition and electronic state of obtained photocatalysts were derived from X-ray photoelectron spectroscopy (XPS) conducted by an X-ray photoelectron spectrometer (AXIS UltraDLD, Kratos, Manchester, UK) with Mg-Kα radiation. Raman spectra measurement was performed on a dispersive Raman microscope (Senterra R200-L, Bruker Optics, Karlsruhe, Germany) with the excitation wavelength of 520 nm. The optical absorption property of obtained photocatalysts was reflected by UV-vis diffuse reflection spectra (DRS) on a UV-Vis spectrophotometer (UV-2450, Shimadzu, Kyoto, Japan) with BaSO 4 as the reference.

Photocatalytic Activity Measurements
The particulate photocatalytic hydrogen evolution was conducted in a 300 mL Pyrex glass reactor under irradiation under visible light, using a 300 W Xe-lamp (CEL-HXF300, Beijing China Education Au-light Co., Ltd., Beijing, China) equipped with an optical filter ranging from 420 to 780 nm, followed with a closed gas circuit system connected with a vacuum pump and online gas chromatography (Huaai GC9160, Huaai, Shanghai, China). 50 mg of (NiMo 6 )@CdS sample was dispersed in an aqueous solution (100 mL) containing 20 vol% 0.05/0.07 mol/L Na 2 S/Na 2 SO 3 through the 10 min sonication.
The photocatalytic reactor was pumped to vacuum to evacuate the dissolved air in the solution. The photocatalysts were in suspension with continuous magnetic stirring while being exposed to light irradiation. The amount of hydrogen evolved per hour was determined by the online gas chromatography equipped with argon as a carrier gas.

Conclusions
In summary, a series of Ni, Mo co-doped CdS photocatalysts with non-noble metal such as Pt, have been prepared by polyoxometalate template-based synthetic strategy with NiMo 6 precursor. 1T-MoS 2 stabilized by the introduction of NiO together with stacking layer structures was successfully decorated on the terrace facets of bulk CdS particles. Due to the modification of the special layer structure, NiO/1T-MoS 2 @CdS composites exhibited a greater photocatalytic performance than pristine Pt-loaded CdS, among which the 5%(NiMo 6 )@CdS sample stood out for its best hydrogen evolution activity with approximately 348.5 µmol/h, in the presence of Na 2 S/Na 2 SO 3 . The AQY efficiency could reach to 42% at 365 nm. The above results illustrated that NiO and 1T-MoS 2 have a synergistic effect on enhancing the separation efficiency of photoexcited electron and hole pairs in CdS and facilitating the interfacial proton reduction, namely hydrogen evolution, at the surface-active site. However, the more detailed charge transfer procedure through the NiO/1T-MoS 2 layer structure still needs clarifying in future research.