Low Noise Low Power Cmos Telescopic-ota for Bio-medical Applications

The preamplifier block is crucial in bio-medical signal processing. The power intensive Operational Transconductance Amplifier (OTA) is considered, and the performance of preamplifier is studied. A low noise and low power telescopic OTA is proposed in this work. To reduce the noise contribution in the active load transistors, source degeneration technique is incorporated in the current stealing branch of the OTA. The OTA design optimization is achieved by g m /I d methodology, which helps to determine the device geometrical parameters (W/L ratio). The proposed design was implemented in CMOS 90 nm with bias current and supply voltage of 1.6 µA and 1.2 V, respectively. The post layout simulation results of the proposed amplifier gave a gain of 62 dB with phase margin 57°, CMRR 78 dB, input referred noise 3.2 µVrms, Noise Efficiency Factor (NEF) 1.86 and power consumption of 1.92 µW.


Introduction
The recent advancement in health monitoring system with NEMS/MEMS technology has opened up the opportunity for integrating a greater number of sensors on a chip (high density) which in its turn allows for better disease diagnosis and treatment of patients.Figure 1 [1] shows the physiological signal's frequency and amplitude distribution in the range of 1 µV-10 mV and 0.5 Hz-10 KHz.This work will focuses on the frequency range of Epilepsy seizure diagnoses using EEG signal which is limited to 100 Hz.Some of the bio-signal recording systems are constructed such that they are implantable, and are placed beneath the skin to record for a fairly long period (7-12 weeks) to diagnose the disorders.These recording systems demand low power consumption, small size [2] and low noise for faithful signal detection.
The preamplifier is shown in Figure 2 [1].It consists of an MOS Depletion Pseudo Resistor (MDPR), coupling capacitor (C 1 ), feed back capacitor (C f ) and load capacitor (C L ).MDPR is used for the rejection of DC offset at the electrode-tissue interface, which emulates high resistance values (Tera ohm) with smaller swing.The midband gain of the preamplifier is decided by the ratio of capacitors (C f /C 1 ) and the bandwidth approximately to g m,OTA /A m * C L .To design preamplifier, OTA is the most important circuit for better performance and also for a power-intensive circuit.The challenging issue is to design a preamplifier with low power, low noise and optimized area.The amplifier should be stable and should collect undistorted signal by rejecting large DC offset voltage due to the interface between the electrode and the tissue [3].Due to bio-compatibility, the existing circuitry still requires improvement in terms of: area, noise level, heat and power dissipation [3].For instance, the power consuming area of 80 mW/cm 2 , produces a heat flux which may cause necrosis in muscle tissue [4].Chaturvedi and Amrutur [2] demonstrated the advantages of open loop over closed loop neural amplifier architectures which are based on the requirement of low frequency signal applications.In their work, they had the benefit of area and power consumption.These open loop architectures have drawbacks in terms of inaccuracy in gain and large distortion.Harrison and Charles [1] achieved better noise level with the cost of power consumption and high bias current.Yang and Holleman [5] demonstrated dual stages, single ended input stage and differential second stage, and focused on supply noise cancellation which achieved better NEF.Nemievosky et al. [6] explained the input referred noise and power spectral density model in saturation and subthreshold regions.They proposed an optimization method to reduce the noise by changing the aspect ratio.Study of the related works reveals the importance of low noise and low power preamplifier design with optimized device geometry.The advantages of single stage telescopic OTA [1] are high gain and area efficiency.Therefore, we propose telescopic OTA with source degeneration in the current stealing branch in this work.Optimized device geometry has been selected based on the g m /I D method shown in Figure 3. Post-layout simulation of the proposed OTA design is carried out with and without source degeneration in the current stealing branch and the results are compared with conventional OTA.This proposed design achieves better noise level and better power consumption.
This paper is organized as follows.Section 2 demonstrates the g m /I D methodology for the proposed OTA.Section 3 reports the proposed OTA with source degeneration in the current stealing branch.Section 4 discuss the obtained post-layout simulation results.

g m /I D Methodology
The g m /I D is a design parameter that reveals the region of operation and aspect ratio of all MOS transistors in a circuit.This g m /I D parameter is obtained by characterization of NMOS and PMOS transistors through simulation for a particular technology [7]. Figure 3 shows the simulation of g m /I D vs.I n (normalized current density) plots for both NMOS and PMOS transistors with (W = 10 × L min ), (L = L min ) in CMOS 90 nm technology.
The design methodology is followed as presented in

Design of Telescopic OTA
Figure 5 shows the schematic of proposed telescopic OTA with source degeneration in the current stealing branch.In the proposed OTA, M0 is a bias transistor, and M1 and M2 are input differential transistors.M3, M4, M5 and M6 are cascode transistors.M7 and M8 are load transistors, M9, M10, M11 and M12 are current stealing transistors.R is the source degenerative resistor in each branch and bias current (I b ) is 1.6 µA, I steal is 710 nA, R = 300 kΩ.The local feedback provided by the degeneration resistor circulates part of the noise current in MOS transistor, without passing it to the output [11].
Bio-amplifier overall performance majorly depends on optimized architecture, proper biasing and sizing of OTA.The design parameters of OTA such as gain, phase margin, UGB, power consumption, noise, slew rate and CMRR can be optimized by proper selection of the Vgs, aspect ratio (W/L) and bias current.Factors influencing the overall performance of the preamplifier are: optimized architecture, proper biasing and sizing of OTA.For low noise and low power design, all transistors are operated in different regions i.e., weak inversion, moderate inversion and strong inversion based on their aspect ratio (W/L).The standard biasing circuits [12] are used to bias the OTA.
This paper proposed a noise reduction technique by introducing source degeneration in the current stealing branch [2,11], which has more impact on noise reduction.Current stealing is a gain enhancement technique.OTA's output impedance is inversely proportional to the drain current and transconductance is directly proportional to the square root of I D .From these relations, gain is inversely proportional to the drain current.The current stealing technique separates the bias currents of input and load transistors to alter the gain and drain currents [13].
Decrement of the current in active load transistors reduces the overall noise and improves the gain.A PMOS input telescopic amplifier with current stealing technique (g m -g m structure) is presented in [1].In this work, the circuit with all PMOS transistors with one side cascode offers less gain.

Proposed Low Noise OTA Design
The Inversion Coefficient (IC) can be calculated, based on the ratio of drain current (I D ) to the moderate inversion (IC = 1, both currents are equal) characteristic current (I S ) [3].
The calculation of the modern inversion characteristic current (I S ) [14] is given by where, U T = Thermal voltage (KT/q) = 26 mV, MOS transistors are modeled using any one of the following: BSIM, PSP, EKV or ACM [15].In this work, EKV semi-empirical model is used.The EKV Model is chosen for low power circuit design and this model is also valid for three regions of operation [16].MOS transistor Trans conductance (g m ) is where, k = Sub threshold slope factor (0.7) is equivalent to 1/n, n represents reciprocal of surface potential.Table 1 shows the different regions of operation based on their Inversion Coefficient (IC) [17].From the Qian [18], the typical "bio-signals" background noise is in the range of 5-10 µVrms.Input referred noise level of OTA should be kept lower than the base level of the "bio-signals" and this noise will effect the OTA performance [19].Design parameters of the proposed OTA (Figure 5) are given in Table 2. To reduce OTA power consumption, the input referred noise should be varied with reference to background noise.By maximizing the input differential pair transconductance (g m1,2 ), input referred noise voltage is reduced from all noise sources like load transistors and resistors with same power consumption.Input transistors are biased in deep subthreshold region with selection of an Inversion Coefficient (IC) value less than 0.1.In order to reduce the noise of telescopic OTA, source degeneration resistors are used which provide significant reduction in flicker noise.Noise contribution of different transistors in a circuit is given by the following relative formulae, Equations ( 4) are ( 5) divided by where, C 1 , C f = input and feedback capacitors, C m is miller capacitance shown in Figure 2. Equations ( 4) and ( 5) represent the contribution of noise current density in MOS transistor per unit hertz.In Equation ( 6) total input-referred noise of OTA is given as ratio of output-referred noise to gain.In Equations ( 7) and ( 8), thermal noise and flicker noise of the OTA are shown in terms of noise contributions of input transistors, load transistors and resistor respectively.The area (W × L)and g m of M 1,2 are inversely proportional and transconductance of M 7,11 is directly proportional to the OTA noise.In Equation ( 9), overall noise of the OTA is represented in terms of ( g m I D ) and corner frequency ( f co ).Equation ( 10) states the impact of OTA noise over preamplifier.By introducing current stealing branch, g m1,2 is increased g m7,8 which reduces the overall input-referred noise of the OTA.Transistor total gate input referred noise is the combination of flicker noise and thermal noise.At critical frequency ( f co ), flicker and thermal noises are equal [20].
Flicker noise in the PMOS transistors is less than NMOS due to less trapping of carriers at the gate and mobility [21].The reason for preferring PMOS as input transistors is that flicker noise is two orders less than NMOS [22].Larger gate area for an input differential pair reduces the flicker noise and causes instability due to larger gate capacitance (W × L area).
Low noise amplifier design needs to optimized according to the sizing and biasing of the input and load transistors.Flicker noise can be minimized by increasing the gate area (W × L) of active transistors as well decreasing the trans conductance (g m ) of load transistors.Gate area can be maximized by increasing the aspect ratio (W/L) for a constant current.Increased gate area in terms of W in × L in leads to a change in region of operation to the subthreshold.Due to larger g m and lower currents, low power is attained.Noise contribution from load transistors is reduced by minimizing the transconductance (g m7,8 ) through reduced current in the load transistors.Due to reduction of a large amount of current in the load transistors, output resistance and resulted gain is increased.Cascode transistors provide larger output resistance and zero noise contribution at the output side.
To minimize the noise within limited power budget, trade-off between noise and power should be considered.NEF is calculated theoretically, which is the noise-power trade-off limit.This limit is achieved by operating the transistors in either weak or strong inversion during implementation.
where, V ni,rms = Input referred noise voltage, I tot = Total bias current, U T = Thermal voltage, K B = Boltzman constant, BW = Bandwidth in Hz.
A single BJT amplifier with zero flicker noise has unity NEF where MOS transistors have accounted for flicker noise.For the proposed OTA, NEF is estimated as 1.86 and compared with the previous works in Table 3.

Simulation and Post Layout Results
Post layout simulation results of proposed telescopic OTA are summarized as follows.All the bio-medical application amplifiers must have input referred noise less than the background noise, i.e., 5-10 µVrms.However, the proposed OTA achieved lesser noise level of 3.2 µVrms with operating frequency of 7 kHz, as shown in Figure 6.For faithful amplification and filtering of signals for bio-medical applications, the amplifier must have a minimum gain of 40 dB and phase margin greater than 45°.Post layout simulation results of the proposed design reveal that gain and phase margin are 62 dB and 57°respectively (as shown in Figure 7).The layout area (as shown Figure 8) of the proposed OTA is optimized to 258.43 µm 2 .Table 3 reports the performance of proposed OTA design along with the other existing works.The comparison statistics between proposed and existing work are not presented since the technology node differs.Akbari and Omid [8] presented a folded cascode amplifier using gm/id methodology for flicker noise minimization.This methodology obtained better improvement in the flicker noise reduction as well as DC gain, gain-bandwidth with low power consumption.Harrinson and Charles [1] proposed a neural amplifier with low noise reduction and high power consumption from mHz to kHz.Chaturvedi and Amrutur [2] presented a paper on ultra low power and low noise neural amplifier.In his work, though new concept of current stealing is introduced and a half-side PMOS cascode is used to reduce the noise, gain is reduced.Yang and Holleman [5] presented an ultra low power low noise neural recording amplifier with better achievement in power, noise and gain with low current and supply voltage of 1 V.The proposed design parameters prove that the OTA is suitable for bio-medical applications.

Conclusions
The main objective of this work is to propose a telescopic OTA for better gain, low noise and power.Introduction of the current stealing branch with source degeneration will enable this proposed telescopic OTA to yield the expected application parameters.The g m /I D methodology is adapted for device geometry and their operating regions.EKV model is recommended for CMOS 90 nm technology.Post layout simulations are carried out with V DD 1.2 V. Proposed OTA achieved 3.2 µVrms low noise level.The input transistors are operated in a subthreshold region where current levels have reduced to 1.6 µA and lead to low power consumption.Simulation results of the present work with reference to gain, power, input referred noise, CMRR and NEF have recommended that the proposed telescopic OTA is more suitable for epileptic seizure detection using EEG signal where noise limitations and gain improvements are required.

Figure 4 . 1 .
Akbari et al. demonstrated  [8,9] g m /I D design flow.Selection of the high g m /I D value from the Figure3ensures lower V gs , larger W and smaller L without reduction in current.This keeps the input transistors (M 1,2 ) operating in weak inversion and leads to minimizing the input-referred noise.2. The selection of a low g m /I D value from Figure3for reducing the input referred noise, ensures high V gs , lower W and larger L, without current reduction.This means that the load and stealing transistors (M

Figure 4 .
Figure 4. Design flow of g m /I D methodology.
OX = Oxide Capacitance per unit area, µ = Mobility of charge carriers, k = Subthreshold gate coupling coefficient (Typically, 0.7) and W L = Aspect ratio of transistor.

Figure 6 .
Figure 6.Total Input referred noise voltage density of the OTA.

Figure 7 .
Figure 7. Post layout simulation results of amplifier gain and phase margin.

Table 1 .
Relation between g m , I D and Region of operation with Inversion Coefficient (IC).

Table 2 .
Operating Parameters for transistors in OTA with I total = 1.6 µA.

Table 3 .
Report of related works done and post layout simulation results of proposed OTA.