Preparing Polypyrrole-Coated Stretchable Textile via Low-Temperature Interfacial Polymerization for Highly Sensitive Strain Sensor

The stretchable sensor has been considered as the most important component in a wearable device. However, it is still a great challenge to develop a highly sensitive textile-based strain sensor with good flexibility, excellent skin affinity, and large dynamic range. Herein, polypyrrole (PPy) was immobilized on a stretchable textile knitted by polyester and spandex via low-temperature interfacial polymerization to prepare a conductive strain sensor for human motion and respiration measurements. Scanning electron microscopy, Fourier transform infrared spectrometry, and thermal gravimetric data verify that a thin layer of PPy has been successfully coated on the textile with a high density and very uniform distribution. The resistance of the as-prepared textile is 21.25 Ω/cm2 and the PPy-coated textile could be used as an electric conductor to light up a LED lamp. Moreover, the textile could tolerate folding at an angle of 180° and 500 times of bending-twisting cycles without significant changes on its resistance. A negative correlation between the resistance change and the applied strain is observed for the textile-based sensor in the strain ranging from 0 to 71% with the gauge factor of −0.46. After more than 200 cycles of stretching-releasing under the strain of 26%, there is no obvious alteration on the sensing responses. The sensors were attached on volunteers’ body or clothes for the real-time measurement of human motions and respiration, demonstrating that the textile-based sensor could sensitively detect finger, elbow, and knee bending and differentiate deep, normal, and fast breath. This work may provide an approach to uniform and dense coating conductive polymers on textiles for highly sensitive and stretchable sensors, which possess great potentials in practical applications for real-time monitoring human motions and physiological signs.


Introduction
As advances of flexible and stretchable electronics, various wearable devices have been developed in the past decades to meet people's requirements on real-time fitness tracking, daily health monitoring, and early disease diagnostics [1,2]. Strain sensors have been considered as crucial building blocks for wearable devices due to their great capability in sensing slight changes of human body and human skin [3]. After being directly attached to the clothes or skin, they could precisely detect a wide range of human motions and physical signs like respiration rate and heart rate [2][3][4][5]. Therefore, it is of great a sensor at its releasing and stretching states. Finally, the as-prepared sensors were fixed on finger, elbow, knee, and abdomen of the volunteers to demonstrate their potentials in practical monitoring of human motion and respiration.

Materials
Pyrrole (99%) was purchased from Adamas-beta Co. (Shanghai, China). Iron chloride hexahydrate (FeCl 3 ·6H 2 O), cyclohexane, and p-toluenesulfonic acid (PTS) were bought from Aladdin Reagent Co. (Shanghai, China). All other chemicals were of analytical grade and directly used without further purification. Deionized water was produced by a Millipore Q water purification system. The polyester/spandex-based stretchable textile was fabricated by BJD Clothes Co. (Zhengjiang, China). Before the experiments, the polyester/spandex textile was cut into small pieces with the desired shapes and sizes to meet the requirements of human motion and respiration measurements.

Preparation of PPy-Coated Textiles
The PPy-functionalized textile was prepared according to Chen's approach with minor modifications [32] (Figure 1). Firstly, 5 mL of 0.4 M FeCl 3 ·6H 2 O and 4 mL of 0.4 M PTS were mixed in a petri dish, followed by pre-cooling at 4 • C for 1 hour. A polyester/spandex-based stretchable textile with the size of 40 by 40 mm 2 was immersed into the above mixture. Then, 9 mL cyclohexane containing 150 µL pyrrole was slowly dropped into the FeCl 3 -PTS aqueous solution. Due to the immiscibility of water and cyclohexane, two phases were formed in the petri dish with the organic phase on top. The whole reaction system was stored at 4 • C for 12 hours. During this process, the color of the textile gradually changed from white to black. The functionalized textile was collected and thoroughly rinsed with water for three times to remove free polymers. Then, the textile was dried at 40 • C for 1 hour. The above procedures were repeated one more time to immobilize a dense PPy layer on the textile.
Micromachines 2019, 10, 788 3 of 11 elbow, knee, and abdomen of the volunteers to demonstrate their potentials in practical monitoring of human motion and respiration.

Materials
Pyrrole (99%) was purchased from Adamas-beta Co. (Shanghai, China). Iron chloride hexahydrate (FeCl3•6H2O), cyclohexane, and p-toluenesulfonic acid (PTS) were bought from Aladdin Reagent Co. (Shanghai, China). All other chemicals were of analytical grade and directly used without further purification. Deionized water was produced by a Millipore Q water purification system. The polyester/spandex-based stretchable textile was fabricated by BJD Clothes Co. (Zhengjiang, China). Before the experiments, the polyester/spandex textile was cut into small pieces with the desired shapes and sizes to meet the requirements of human motion and respiration measurements.

Preparation of PPy-Coated Textiles
The PPy-functionalized textile was prepared according to Chen's approach with minor modifications [32] (Figure 1). Firstly, 5 mL of 0.4 M FeCl3•6H2O and 4 mL of 0.4 M PTS were mixed in a petri dish, followed by pre-cooling at 4 °C for 1 hour. A polyester/spandex-based stretchable textile with the size of 40 by 40 mm 2 was immersed into the above mixture. Then, 9 mL cyclohexane containing 150 μL pyrrole was slowly dropped into the FeCl3-PTS aqueous solution. Due to the immiscibility of water and cyclohexane, two phases were formed in the petri dish with the organic phase on top. The whole reaction system was stored at 4 °C for 12 hours. During this process, the color of the textile gradually changed from white to black. The functionalized textile was collected and thoroughly rinsed with water for three times to remove free polymers. Then, the textile was dried at 40 °C for 1 hour. The above procedures were repeated one more time to immobilize a dense PPy layer on the textile.

Characterization
Surface morphologies of the polyester/spandex textiles before and after PPy modification were characterized using a JSM-7600 FESEM (JEOL, Tokyo, Japan). A smartphone-attached optical microscope (Wellwa, Guangdong, China) was applied to image the structural change of the PPycoated textile under tension at micrometer scale. The surface functional groups and the thermal stability of the textile before and after PPy coating were examined with a Fourier transform infrared spectrometer (FTIR, Nicolet 6700, Thermo Electronic Corporation, Waltham, MA, USA) and a SDT-Q600 thermogravimetric analyzer (TA Instruments, New Castle, DE, USA), respectively.

Characterization
Surface morphologies of the polyester/spandex textiles before and after PPy modification were characterized using a JSM-7600 FESEM (JEOL, Tokyo, Japan). A smartphone-attached optical microscope (Wellwa, Guangdong, China) was applied to image the structural change of the PPy-coated textile under tension at micrometer scale. The surface functional groups and the thermal stability of the textile before and after PPy coating were examined with a Fourier transform infrared spectrometer (FTIR, Nicolet 6700, Thermo Electronic Corporation, Waltham, MA, USA) and a SDT-Q600 thermogravimetric analyzer (TA Instruments, New Castle, DE, USA), respectively.

Strain Sensing Tests
The resistances of the PPy-coated polyester/spandex textiles were measured using a Keithley 2400 Source Meter. A 20 mm by 40 mm textile was bent at an angle of 0-180 • for the measurement of its resistance alteration. The resistance of the same textile was also examined after 500 times of bending or twisting to investigate the stability of the PPy layer. The textiles with the size of 20 mm by 40 mm were stretched with an electronic universal testing machine (WDW-211, Jinan, China) at the velocity of 500 mm/min to achieve the designed strains. Strain-induced resistance changes were collected to explore the strain sensing range.

On-Body Tests
The PPy-coated polyester/spandex textiles shaped as per the requirements of on-body measurements were fixed on clothes or skin to demonstrate their potentials in practical applications. The sensing performance of the device were collected with an electrochemical workstation (CHI 660E, CH Instrument Company, Shanghai, China). The current changes induced by the bending of finger, elbow, and knee were measured with the PPy-coated textile at an operating voltage of 0.1 V. The textile-based sensor was also attached on the volunteer's abdomen to sense the up and down movement caused by human breathing. The current patterns were collected to track deep breath, fast breath, and normal breath.

Results and Discussion
SEM was employed to characterize surface morphologies of polyester/spandex textiles before and after PPy immobilization. As shown in Figure 2a,c, the pristine polyester/spandex textile is woven with fibers, which possess very smooth surface and the diameter of~20 µm. After low-temperature interface polymerization, the fiber surface became rough ( Figure 2b) and a lot of small particles could be observed (Figure 2d). High-magnified image (Inset of Figure 2d) further illustrates that the fiber is fully covered with a dense and uniform film, which is significantly different from the loosely attached particles prepared with chemical oxidative polymerization at room temperature [33]. The greatly reduced reaction rate and the polymerization occurred at the interface between two phases may cause the formation of the uniform and thin PPy layer. The data strongly proves that PPy has been successfully immobilized on the textile surface to function as a continuous conductive layer. The same approach could also be applied to successfully immobilize PPy on nylon/lycra, silk, and cotton textiles. Their maximum strains much lower than that of PPy-coated polyester/spandex textile. Thus, we chose polyester/spandex textile as the substrate to prepare the strain sensor in this work (Figures S1 and S2 in supporting information).
FTIR spectra were collected to further verify the existence of PPy on the textiles. In comparison to pristine polyester/spandex textile, two weak peaks appear at 1447 and 1531 cm −1 in the spectra of the PPy-coated one ( Figure 3a). The former peak could be attributed to the C=C and C-C stretching vibration of PPy ring [32]. The latter one may be ascribed to the pyrrole ring characteristic vibration [34]. The thermal stability of the textiles was also investigated by measuring the weight change in the temperature range of 25-700 • C under the nitrogen atmosphere. It can be seen from Figure 3b that the weight of the pristine textile keeps at a very stable level as temperature increases from 25 to 400 • C. However, after PPy coating, the sample undergoes a gradual weight loss of~5%, which may be due to the breakdown of the PPy backbone and chemical decomposition of the dopant FeCl 3 . Interestingly, the remaining weights of pristine and PPy-modified textiles at 700 • C are 14.6% and 25.0%, respectively. The relatively high content of carbon element in PPy may lead to the remarkable enhancement on the residue weight of PPy-modified sample. The FTIR and TGA data also verify that the PPy has been immobilized on the textiles, agreeing well with the SEM images.
has been successfully immobilized on the textile surface to function as a continuous conductive layer. The same approach could also be applied to successfully immobilize PPy on nylon/lycra, silk, and cotton textiles. Their maximum strains much lower than that of PPy-coated polyester/spandex textile. Thus, we chose polyester/spandex textile as the substrate to prepare the strain sensor in this work (Figures S1, S2 in supporting information).  FTIR spectra were collected to further verify the existence of PPy on the textiles. In comparison to pristine polyester/spandex textile, two weak peaks appear at 1447 and 1531 cm −1 in the spectra of the PPy-coated one (Figure 3a). The former peak could be attributed to the C=C and C-C stretching vibration of PPy ring [32]. The latter one may be ascribed to the pyrrole ring characteristic vibration [34]. The thermal stability of the textiles was also investigated by measuring the weight change in the temperature range of 25-700 °C under the nitrogen atmosphere. It can be seen from Figure 3b that the weight of the pristine textile keeps at a very stable level as temperature increases from 25 to 400 °C. However, after PPy coating, the sample undergoes a gradual weight loss of ~5%, which may be due to the breakdown of the PPy backbone and chemical decomposition of the dopant FeCl3. Interestingly, the remaining weights of pristine and PPy-modified textiles at 700 °C are 14.6% and 25.0%, respectively. The relatively high content of carbon element in PPy may lead to the remarkable enhancement on the residue weight of PPy-modified sample. The FTIR and TGA data also verify that the PPy has been immobilized on the textiles, agreeing well with the SEM images. Before the sensing tests, the resistance of the PPy-coated polyester/spandex textile is measured as 21.25 Ω/cm 2 , which is comparable to the PPy-modified polyester/spandex and cotton/spandex fabrics [35]. We changed the pyrrole volume in the polymerization system to control the amount of PPy coated on the textiles. As the monomer volume rises from 50 to 150 μL, the amount of PPy coated on the textiles gradually increases. When the volume further enhances to 200 μL, a slight reduction on the PPy amount is observed ( Figure S3a in supporting information). Moreover, the amount of surface-coated PPy could significantly affect the conductivity of the textile. Large amount of PPy on the textile may lead to a high level of conductivity ( Figure S3b in supporting information). Since the conductive textile is designed as a strain sensor, we must rule out the interferences of bending and twisting on the textile resistance. Thus, we investigated the effects of bending angle and repeated bending/twisting on the normalized resistance of the PPy-functionalized textile. When the textile was bent from 0° to 180°, the resistance remains at a constant level, suggesting that the bending does not affect its electronic property. Since bending and twisting cannot be avoided during the practical applications of wearable devices, the influences of repeated bending and twisting on the textile resistance were also studied. As shown in Figure 4b,c, the normalized resistance is also stable during 500 times of twisting and bending, indicating that the textile can tolerate repeated bending and twisting without alteration on the device conductivity. To demonstrate the conductivity, a PPy- Before the sensing tests, the resistance of the PPy-coated polyester/spandex textile is measured as 21.25 Ω/cm 2 , which is comparable to the PPy-modified polyester/spandex and cotton/spandex fabrics [35]. We changed the pyrrole volume in the polymerization system to control the amount of PPy coated on the textiles. As the monomer volume rises from 50 to 150 µL, the amount of PPy coated on the textiles gradually increases. When the volume further enhances to 200 µL, a slight reduction on the PPy amount is observed ( Figure S3a in supporting information). Moreover, the amount of surface-coated PPy could significantly affect the conductivity of the textile. Large amount of PPy on the textile may lead to a high level of conductivity ( Figure S3b in supporting information). Since the conductive textile is designed as a strain sensor, we must rule out the interferences of bending and twisting on the textile resistance. Thus, we investigated the effects of bending angle and repeated bending/twisting on the normalized resistance of the PPy-functionalized textile. When the textile was bent from 0 • to 180 • , the resistance remains at a constant level, suggesting that the bending does not affect its electronic property. Since bending and twisting cannot be avoided during the practical applications of wearable devices, the influences of repeated bending and twisting on the textile resistance were also studied. As shown in Figure 4b,c, the normalized resistance is also stable during 500 times of twisting and bending, indicating that the textile can tolerate repeated bending and twisting without alteration on the device conductivity. To demonstrate the conductivity, a PPy-immobilized textile was connected with a LED and two batteries in series. The textile could function as an electrical conductor to light up a LED lamp with lowest working voltage of 2.0 V (Figure 4d). The tensile property of the PPy-coated polyester/spandex textile is quite different in the wasp and weft directions. Along the weft direction, the textile can be stretched up to the strain of 100%, which is ~2 times higher than the maximum strain in the wasp direction ( Figure 5a). Therefore, in the following experiments, the stretching force was applied along the weft direction to investigate the properties of the textile-based strain sensor. The gauge factor (GF) is employed to evaluate the tensile sensitivity according to the following equation: Where ΔR and R0 are the change of resistance and the initial resistance, respectively, and ɛ is the strain applied in the test. As illustrated in Figure 5b, the normalized resistance change is negatively correlated to the strain applied to the PPy-coated textile in the strain range of 0 to 71% with R 2 of 0.96 (Figure 5b). The GF is calculated to be −0.46 in the linear sensing range (0-71%). The performance of the textile-based strain sensor could be prominently affected by the amount of PPy coating layer ( Figure S3 in supporting information). When the mass ratios of PPy on the textiles are 0.128 and 0.180, the stretching of the sensors induce the enhancement of the textile resistance. On the contrary, the resistance of the sensor decreases at the stretching state as the mass ratio increases to 0.183. It can be clearly seen that the sensor with the PPy mass ratio of 0.183, which was prepared at the monomer volume of 150 μL, has the largest absolute value of GF and the widest sensing range. The durability of the PPy-coated polyester/spandex sensor is studied under stretching-releasing cycles with the strain of 26% and the applied voltage of 0.1 V. It can be seen that the current responses to the repeated stretching and releasing keeps very stable even after 200 cycles (Figure 5c). Significant changes on the current profiles occur after 200 stretching-releasing cycles, indicating that the sensor can tolerate 200 times of stretching-releasing without alteration on its sensing performance ( Figure S4 in supporting information). The non-uniform stretching velocity applied by the universal testing machine may lead to the zigzag current changes in Figure 5c. In comparison to the strain sensors based on PPy-coated textiles that were prepared with other approaches [11,22,31,[36][37][38], the as-prepared one possesses the largest dynamic range as well as the comparable GF and conductivity (Table 1). More importantly, for the textile-based sensor, the resistance at the stretching state is lower than that at the releasing The tensile property of the PPy-coated polyester/spandex textile is quite different in the wasp and weft directions. Along the weft direction, the textile can be stretched up to the strain of 100%, which is 2 times higher than the maximum strain in the wasp direction ( Figure 5a). Therefore, in the following experiments, the stretching force was applied along the weft direction to investigate the properties of the textile-based strain sensor. The gauge factor (GF) is employed to evaluate the tensile sensitivity according to the following equation: where ∆R and R 0 are the change of resistance and the initial resistance, respectively, and is the strain applied in the test. As illustrated in Figure 5b, the normalized resistance change is negatively correlated to the strain applied to the PPy-coated textile in the strain range of 0 to 71% with R 2 of 0.96 (Figure 5b). The GF is calculated to be −0.46 in the linear sensing range (0-71%). The performance of the textile-based strain sensor could be prominently affected by the amount of PPy coating layer ( Figure S3 in supporting information). When the mass ratios of PPy on the textiles are 0.128 and 0.180, the stretching of the sensors induce the enhancement of the textile resistance. On the contrary, the resistance of the sensor decreases at the stretching state as the mass ratio increases to 0.183. It can be clearly seen that the sensor with the PPy mass ratio of 0.183, which was prepared at the monomer volume of 150 µL, has the largest absolute value of GF and the widest sensing range. The durability of the PPy-coated polyester/spandex sensor is studied under stretching-releasing cycles with the strain of 26% and the applied voltage of 0.1 V. It can be seen that the current responses to the repeated stretching and releasing keeps very stable even after 200 cycles (Figure 5c). Significant changes on the current profiles occur after 200 stretching-releasing cycles, indicating that the sensor can tolerate 200 times of stretching-releasing without alteration on its sensing performance ( Figure S4 in supporting information). The non-uniform stretching velocity applied by the universal testing machine may lead to the zigzag current changes in Figure 5c. In comparison to the strain sensors based on PPy-coated textiles that were prepared with other approaches [11,22,31,[36][37][38], the as-prepared one possesses the largest dynamic range as well as the comparable GF and conductivity (Table 1). More importantly, for the textile-based sensor, the resistance at the stretching state is lower than that at the releasing state.
A much more significant current signal may be collected at a higher strain under a constant applied voltage, which is favorable for the practical applications.    To understand the sensing mechanism, a PPy-coated textile was examined using an optical microscope at both releasing and stretching states (Figure 6a,b). A typical woven structure could be observed in both images. At the releasing state, the fibers are loosely entangled together. When the strain is applied in the weft direction, the warp fibers are aligned and tightly hold together with each other. According to Holm's contact resistance theory, higher pressure and more contact points lead to the lower contact resistance [38]. Since PPy has been coated on the fibers during the low-temperature polymerization process, the tight contacts of the fibers may significantly increase the pathways in the textiles for the electron transfer, thus reducing the resistance of the sensors (Figure 6c). However, the effects of strain on individual fibers should also be considered in the sensing mechanism. The application of a strain may lead to the rupture of the PPy coating layer, which obviously leads to the enhancement of the textile resistance. Therefore, the strain-induced addition of the electron transfer pathways and rupture of the conductive coating layers may both contribute to the performance of the textile-based sensors. As shown in Figure S3 (ESI), positive GFs were observed in the textiles with thin PPy layers because of the easy fraction of the conductive layers under tensile loading. While, negative GFs appear in the samples containing more PPy since the addition of contact points plays a prominent role. obviously leads to the enhancement of the textile resistance. Therefore, the strain-induced addition of the electron transfer pathways and rupture of the conductive coating layers may both contribute to the performance of the textile-based sensors. As shown in Figure S3 (ESI), positive GFs were observed in the textiles with thin PPy layers because of the easy fraction of the conductive layers under tensile loading. While, negative GFs appear in the samples containing more PPy since the addition of contact points plays a prominent role. To further demonstrate the feasibility of the strain sensor based on PPy-coated polyester/spandex textiles, the devices were fixed on body to test their capability for human motion and respiration monitoring. As shown in Figure 7a-c, repeated bending of finger, elbow, and knee could be sensitively real-time detected with the as-prepared strain sensors. Once the volunteer bends the finger, elbow, and knee, stretching forces are applied to the sensors, resulting in the sharp reduction of the resistance. As the finger, elbow, and knee are straightened again, the resistances recover to the original levels. The PPy-coated textile was also stitched on the clothes to sense the breath-caused changes on the abdomen (Figure 7d). During the inhalation process, the abdomen contracts, leading to the rising of resistance. The abdomen relaxes in the exhalation process and the resistance decreases. The strain sensor can not only monitor the respiration rate, but also differentiate various breathing patterns like deep breath, normal breath, and fast breath. Inspired by Zhao and Shu's work [39][40][41], to demonstrate its great compatibility with daily clothing, the textile-based sensor was stitched on a glove for the sensing of finger bending, also showing very sensitive responses (Figure 7e). Based on above results, it can be concluded that the PPy-coated polyester/spandex textile is very promising to be used as the strain sensor for real-time monitoring human motions and precise tracking human's cardiopulmonary function. To further demonstrate the feasibility of the strain sensor based on PPy-coated polyester/spandex textiles, the devices were fixed on body to test their capability for human motion and respiration monitoring. As shown in Figure 7a-c, repeated bending of finger, elbow, and knee could be sensitively real-time detected with the as-prepared strain sensors. Once the volunteer bends the finger, elbow, and knee, stretching forces are applied to the sensors, resulting in the sharp reduction of the resistance. As the finger, elbow, and knee are straightened again, the resistances recover to the original levels. The PPy-coated textile was also stitched on the clothes to sense the breath-caused changes on the abdomen (Figure 7d). During the inhalation process, the abdomen contracts, leading to the rising of resistance. The abdomen relaxes in the exhalation process and the resistance decreases. The strain sensor can not only monitor the respiration rate, but also differentiate various breathing patterns like deep breath, normal breath, and fast breath. Inspired by Zhao and Shu's work [39][40][41], to demonstrate its great compatibility with daily clothing, the textile-based sensor was stitched on a glove for the sensing of finger bending, also showing very sensitive responses (Figure 7e). Based on above results, it can be concluded that the PPy-coated polyester/spandex textile is very promising to be used as the strain sensor for real-time monitoring human motions and precise tracking human's cardiopulmonary function. 10,788 ponses of the textile-based strain sensors to human finger bending (a), elb bending (c). Inserts are the photos showing the attachment of the device al-time measurements of respiration by fixing a sensor on the volunteer's a asurements of finger bending by a glove-stitched sensor.
, we have prepared a PPy-coated stretchable textile via low-temper ethod to function as a sensitive and wearable strain sensor for mo piration. The PPy film is uniformly and densely deposited on the uous conductive layer, rendering the as-prepared textile with the cm 2 . The as-prepared textile could be used as an electrical conduc importantly, it can tolerate 500 times of bending and twisting wi esistance. The tensile tests show that the textile-based strain sen

Conclusions
In summary, we have prepared a PPy-coated stretchable textile via low-temperature interfacial polymerization method to function as a sensitive and wearable strain sensor for monitoring human motions and respiration. The PPy film is uniformly and densely deposited on the textile surface to produce a continuous conductive layer, rendering the as-prepared textile with the conductivity as high as 21.25 Ω/cm 2 . The as-prepared textile could be used as an electrical conductor to light up a LED lamp. More importantly, it can tolerate 500 times of bending and twisting without significant change on its resistance. The tensile tests show that the textile-based strain sensor possesses a negatively dynamic range from 0 to 71% with GF as −0.46. After more than 200 cycles of stretching-releasing under the strain of 26%, there is no obvious alteration on the sensing response. The on-body investigations further demonstrate that the sensor based on PPy-coated polyester/spandex textile could sensitively detect human motions like finger, elbow, and knee bending and differentiate human respiration patterns like deep, normal, and fast breath. This work may not only develop a strain sensor based on PPy-coated textile for practical applications in wearable electronics, but also provide an approach for the uniform and dense coating of conductive polymers on textiles.
Supplementary Materials: The following are available online at http://www.mdpi.com/2072-666X/10/11/788/s1, Figure S1: SEM images of pristine nylon/lycra, silk and cotton fabrics at low (a,e,i) and high magnifications (c,g,k); SEM images of PPy-caoted nylon/lycra, silk and cotton fabrics at low (b,f,j) and high magnifications (d,h,l). Figure S2: PPy-coated polyester/spandex, nylon/lycra, silk and cotton textiles stretched to the maximum strain. Figure S3: Mass ratios (a) of surface-coated PPy to the textile and resistance ratios (b) of the as-prepared conducting textiles after polymerization with different volume of Py. Relative resistance change (∆R/R 0 ) of the as-prepared textiles prepared with 50 µL Py (c), 100 µL Py (d), 150 µL Py (e) and 200 µL Py (f). Figure S4: Current responses of a textile-based sensor upon periodic stretching-releasing cycles under a strain of 26%.
Funding: This work was financially supported by Chongqing Natural Science Foundation (cstc2019jcyj-msxmX0314), Fundamental Research Funds for the Central Universities (XDJK2019B002 and XDJK2018B003) and Chongqing Engineering Research Center for Micro-Nano Biomedical Materials and Devices.

Conflicts of Interest:
The authors declare no conflict of interest.