Oxidation of Cylindrospermopsin by Fenton Process: A Bench-Scale Study of the Effects of Dose and Ratio of H2O2 and Fe(II) and Kinetics

The cyanotoxin cylindrospermopsin (CYN) has become a significant environmental and human health concern due to its high toxicological potential and widespread distribution. High concentrations of cyanotoxins may be produced during cyanobacterial blooms. Special attention is required when these blooms occur in sources of water intended for human consumption since extracellular cyanotoxins are not effectively removed by conventional water treatments, leading to the need for advanced water treatment technologies such as the Fenton process to produce safe water. Thus, the present study aimed to investigate the application of the Fenton process for the degradation of CYN at bench-scale. The oxidation of CYN was evaluated by Fenton reaction at H2O2/Fe(II) molar ratio in a range of 0.4 to 4.0, with the highest degradation of about 81% at molar ratio of 0.4. Doubling the concentrations of reactants for the optimized H2O2/Fe(II) molar ratio, the CYN degradation efficiency reached 91%. Under the conditions studied, CYN degradation by the Fenton process followed a pseudo-first-order kinetic model with an apparent constant rate ranging from 0.813 × 10−3 to 1.879 × 10−3 s−1.


Introduction
Although natural aquatic ecosystems can be eutrophic as water bodies age and are filled in with sediments [1], human activities, such as agriculture, industry, and sewage disposal, can speed up the natural eutrophication of lentic systems by increasing the load of nutrients, resulting in anthropogenic eutrophication. The nutrients enrichment of an aquatic environment, mainly due to nitrogen and phosphorus, leads to a rapid growth of cyanobacteria, algae, and aquatic plants, which results in a shift in the biodiversity and ecosystem balance, compromising the water quality and various uses of water [2][3][4][5][6][7].
The fast growth of cyanobacteria in eutrophic waters, most frequently referred to as cyanobacterial bloom, can be harmful when the toxins produced by these organisms (cyanotoxins) reach dangerous concentrations to humans and animals. Dozens of genera and species of cyanobacteria are capable of producing toxins [8][9][10], which are classified as secondary metabolites.
The cylindrospermopsins (CYNs) are among the cyanotoxins of most significant health concern. These cyanotoxins are produced by species of various genera, including Raphidiopsis (previously Cylindrospermopsis), Aphanizomenon, Dolichospermum (previously 2Fe(II) The degradation efficiency of the Fenton process depends on several parameters: pH, reaction time, temperature, initial concentration of pollutant, as well as reagents dosage and H 2 O 2 /Fe(II) molar ratio [47,48] since H 2 O 2 and Fe(II) can also scavenge hydroxyl radicals (Equations (3) and (4)) if their concentrations are not optimized. The reagents dosage also reflects on the cost of the process and on the solids concentration, which can increase the iron sludge production and impair further treatment steps or discharge when high concentrations of Fe(II) are used [49].
To the best of our knowledge, no previously published study focused on CYN degradation by the traditional Fenton process. Only recently, however, few studies concerning the CYN oxidation by Fenton-like processes are available and reported a CYN degradation efficiency of around 90% [64,65]. The high CYN degradation efficiency obtained by using Fenton-like processes (Equation (2)), which are generally slower than Fenton process (Equation (1)), shows the promising potential for the CYN degradation by Fenton process. Additionally, the uracil ring, which is critical to CYN toxicity [66], is very susceptible to oxidation by hydroxyl radical [67,68]. Thus, the present study aimed to evaluate the oxidation (degradation) of CYN using Fenton process, at bench-scale, with emphasis on the effects of H 2 O 2 /Fe(II) molar ratio and the initial concentrations of H 2 O 2 and Fe (II) on this cyanotoxin oxidation efficiency as well as the oxidation kinetics.

The Effect of H 2 O 2 /Fe(II) Molar Ration on CYN Degradation
As pointed out in the Materials and Methods (Section 4.1), two sets of experiments were carried out to evaluate the effect of H 2 O 2 /Fe(II) molar ratio on the CYN degradation. In the first set, the initial H 2 O 2 concentration was kept constant at 25 µM; and, in the second one the initial Fe(II) concentration was kept constant at 25 µM. Figure 1 presents the average results of the two sets.
The highest CYN degradation efficiency of 81% was achieved with an H 2 O 2 /Fe(II) molar ratio of 0.4 in the first set of experiments ( Figure 1a) and 65% with H 2 O 2 /Fe(II) molar ratio of 1.0 in the second set of experiments. The effect of H 2 O 2 /Fe(II) molar ratio on the CYN oxidation presents a similar behavior in both sets of experiments, although the difference in the optimum H 2 O 2 /Fe(II) molar ratio. Regarding the blank synthetic water used to evaluate the degradation of CYN over the reaction time in the absence of Fenton reagents, less than 5% of CYN degradation was observed as expected because CYN standard is relatively stable in ultrapure water [20].
Comparing the CYN degradation efficiency at H 2 O 2 /Fe(II) molar ratio of 0.4 in the two sets of experiments, the lower degradation of 58% observed in the second set ( Figure 1b) can be explained by the initial H 2 O 2 and Fe(II) concentrations, which were 2.5 times lower in the second set than in the first set of experiments (see Figure 5). Additionally, comparing the relative residual Fenton reagents, while the relative residual H 2 O 2 was approximately similar in both sets of experiments, the relative residual Fe(II) was at least two times lower in the first set ( Figure 1b) than in the second set (Figure 1a), indicating that the increase in the Fenton reagents, especially Fe(II), increased the hydroxyl radical scavenging activity (see Equation (4)) and consequently the Fe(II) consumption. The highest CYN degradation efficiency of 81% was achieved with an H2O2/Fe(II) molar ratio of 0.4 in the first set of experiments ( Figure 1a) and 65% with H2O2/Fe(II) molar ratio of 1.0 in the second set of experiments. The effect of H2O2/Fe(II) molar ratio on the CYN oxidation presents a similar behavior in both sets of experiments, although the difference in the optimum H2O2/Fe(II) molar ratio. Regarding the blank synthetic water used to evaluate the degradation of CYN over the reaction time in the absence of Fenton reagents, less than 5% of CYN degradation was observed as expected because CYN standard is relatively stable in ultrapure water [20].
Comparing the CYN degradation efficiency at H2O2/Fe(II) molar ratio of 0.4 in the two sets of experiments, the lower degradation of 58% observed in the second set ( Figure  1b) can be explained by the initial H2O2 and Fe(II) concentrations, which were 2.5 times lower in the second set than in the first set of experiments (see Figure 5). Additionally, comparing the relative residual Fenton reagents, while the relative residual H2O2 was approximately similar in both sets of experiments, the relative residual Fe(II) was at least two times lower in the first set ( Figure 1b) than in the second set (Figure 1a), indicating that the increase in the Fenton reagents, especially Fe(II), increased the hydroxyl radical scavenging activity (see Equation (4)) and consequently the Fe(II) consumption.
The increase of the initial Fe(II) concentration may have led to a reduction in final pH as the hydrolysis of Fe(III) yielded in the Fenton reaction (Equation (1)) contributes to water acidification [69] (Figure 2a). The final pH at H2O2/Fe(II) molar ratio of 0.4 was lower in the first set of experiments ( Figure 2a) than in the second set ( Figure 2b). As higher degradation efficiencies of the Fenton process were reported at acidic conditions (pH values between 3 and 4) [61,70,71], the lowest final pH observed in the first set of experiments might have increased hydroxyl radical generation and consequently the CYN oxidation. As can be seen in Figure 1, the degradation efficiency of CYN decreased when H2O2/Fe(II) molar ratio increased from 0.4 to 1.6 and remained constant at higher H2O2/Fe(II) ratios. The observed reduction in the degradation efficiency of CYN may be explained by the scavenging of hydroxyl radicals by the excess H2O2 (see Equation (3)) since the residual CYN concentrations showed a similar trend as the residual H2O2. Furthermore, the scavenging of hydroxyl radicals by H2O2 leads to the generation of hydrop-   As can be seen in Figure 1, the degradation efficiency of CYN decreased when H 2 O 2 /Fe(II) molar ratio increased from 0.4 to 1.6 and remained constant at higher H 2 O 2 /Fe(II) ratios. The observed reduction in the degradation efficiency of CYN may be explained by the scavenging of hydroxyl radicals by the excess H 2 O 2 (see Equation (3)) since the residual CYN concentrations showed a similar trend as the residual H 2 O 2 . Furthermore, the scavenging of hydroxyl radicals by H 2 O 2 leads to the generation of hydroperoxyl radical that has a lower oxidation potential, 1.7 V (SHE), than the hydroxyl radical, 2.8 V (SHE) [72].
Concerning the high percentage of residual H 2 O 2 (from 50 to 69%) and the low percentage of residual Fe(II) (from 1 to 9%) at H 2 O 2 /Fe(II) molar ratios above 1.0, higher degradation efficiency could be achieved over a long time since the regeneration of Fe(II) can be accomplished by residual H 2 O 2 by the Fenton-like reaction (Equation (2)). However, the Fenton-like reaction is very slow (second-order rate constant of 0.001 to 0.01 M −1 s −1 [44]) in comparison with the Fenton main reaction (second-order rate constant of 70 M −1 s −1 [43]), Equation (1).
Despite the high reactivity of hydroxyl radical with Fe(II) in comparison with H 2 O 2 , with second-order rate constants respectively of 3.2 × 10 8 and 3.3 × 10 7 M −1 s −1 [45], low H 2 O 2 /Fe(II) molar ratios resulted in higher CYN degradation. However, the optimal H 2 O 2 /Fe(II) molar ratios observed in this study are in accordance with the molar ratios of the Fenton main (Equation (1)) and global (Equation (8)) reactions, which suggests that H 2 O 2 /Fe(II) molar ratios less than or equal to 1 might favor the hydroxyl radical generation. It must be emphasized that there is no consensus regarding the optimum H 2 O 2 /Fe(II) molar ratio since it also depends on specific conditions such as pH and type and concentration of pollutant. For MCs degradation by the Fenton process, the optimum H 2 O 2 /Fe(II) molar ratio reported is in a range of 0.7 to 15 [36,[59][60][61].
Based on the CYN oxidation efficiencies, the value of 0.4 obtained from the first set of experiments was adopted as the optimum H 2 O 2 /Fe(II) molar ratio (25 µM H 2 O 2 and 62.5 µM Fe(II)) for CYN degradation by the Fenton process for the conditions evaluated in this study.

The Effect of Initial H 2 O 2 and Fe(II) Concentration on CYN Degradation
The effect of initial Fenton reagents concentrations on CYN degradation was evaluated at the optimal H 2 O 2 /Fe(II) molar ratio of 0.4 obtained from the first set of experiments in Phase 1 with initial H 2 O 2 and Fe(II) concentrations of 0.4, 1.0, and 2.0 times their optimal concentrations (25 µM H 2 O 2 and 62.5 µM Fe(II)). Figure 3 shows the relative residual concentration (C/C 0 ) of CYN, H 2 O 2 , and Fe(II) and the pH-time profile for various initial concentrations of H 2 O 2 and Fe(II).
The appropriate concentrations of H 2 O 2 and Fe(II) are a key factor in enhancing the efficiency of the Fenton process. The analysis of reagent blank synthetic water showed that no significant CYN degradation (less than 10%) was observed at the highest concentrations of Fenton reagents when tested alone, that is, 100 µM H 2 O 2 alone and 125 µM Fe(II) alone. Munoz and co-workers [64] also found no significant CYN degradation by heterogeneous Fenton-like reagents (H 2 O 2 and Fe 3 O 4 -R400) when tested independently.
On the other hand, the Fe(II) and H 2 O 2 interaction can lead to higher CYN degradation, even at low initial concentrations. As can be seen in Figure 3a In addition, the relative residual H 2 O 2 has remained almost constant, around 6%, while the relative residual Fe(II) decreased from 76% to 21% when the initial Fe(II) concentration increased from 25 to 125 µM ( Figure 3a). As previously mentioned, this reduction in the relative residual Fe(II) was probably caused by the oxidation of Fe(II) to Fe(III) by hydroxyl radicals (Equation (4)).
Such behaviour suggests that, even at a fixed H 2 O 2 /Fe(II) molar ratio, the increase in the Fenton reagents led to an increase in the hydroxyl radical scavenging activity that can slow the rise in CYN degradation, as observed in Figure 3a. This explains why the increase concentrations (25 µM H2O2 and 62.5 µM Fe(II)). Figure 3 shows the relative residual concentration (C/C0) of CYN, H2O2, and Fe(II) and the pH-time profile for various initial concentrations of H2O2 and Fe(II). The appropriate concentrations of H2O2 and Fe(II) are a key factor in enhancing the efficiency of the Fenton process. The analysis of reagent blank synthetic water showed that no significant CYN degradation (less than 10%) was observed at the highest concentrations of Fenton reagents when tested alone, that is, 100 µM H2O2 alone and 125 µM Fe(II) alone. Munoz and co-workers [64] also found no significant CYN degradation by heterogeneous Fenton-like reagents (H2O2 and Fe3O4-R400) when tested independently.
On the other hand, the Fe(II) and H2O2 interaction can lead to higher CYN degradation, even at low initial concentrations. As can be seen in Figure 3.a, the CYN degradation was 49% with 10 µM H2O2 and 25 µM Fe(II), 81% with 25 µM H2O2 and 62.5 µM Fe(II), and 91% with 50 µM H2O2 and 125 µM Fe(II).
In addition, the relative residual H2O2 has remained almost constant, around 6%, while the relative residual Fe(II) decreased from 76% to 21% when the initial Fe(II) concentration increased from 25 to 125 µM ( Figure 3a). As previously mentioned, this reduction in the relative residual Fe(II) was probably caused by the oxidation of Fe(II) to Fe(III) by hydroxyl radicals (Equation (4)).
Such behaviour suggests that, even at a fixed H2O2/Fe(II) molar ratio, the increase in the Fenton reagents led to an increase in the hydroxyl radical scavenging activity that can slow the rise in CYN degradation, as observed in Figure 3.a. This explains why the increase from 25 µM H2O2 and 62.5 µM Fe(II) to 50 µM H2O2 and 125 µM Fe(II) only resulted in a rise of 10% in the CYN degradation, suggesting an asymptotic trend. This trend indicates that the CYN degradation by the Fenton process follows a reaction with an order greater than zero as the different initial concentrations of Fenton reagents resulted in different relative residual CYN after 30 min reaction (Figure 3).
Similarly, Park and co-workers [59], concerning the degradation of MC-LR by the Fenton process, also observed that increasing the H2O2 and Fe(II) concentration at a fixed H2O2/Fe(II) ratio increased the degradation efficiency until they reach a certain concentration above which all degradation efficiency increases appear to be insignificant.
The increase of the initial Fe(II) concentration diminished the final pH of the solution (Figure 3b), as also observed in the first set of experiments in Phase 1 (Figure 2a). As pre- Similarly, Park and co-workers [59], concerning the degradation of MC-LR by the Fenton process, also observed that increasing the H 2 O 2 and Fe(II) concentration at a fixed H 2 O 2 /Fe(II) ratio increased the degradation efficiency until they reach a certain concentration above which all degradation efficiency increases appear to be insignificant.
The increase of the initial Fe(II) concentration diminished the final pH of the solution (Figure 3b), as also observed in the first set of experiments in Phase 1 (Figure 2a). As previously mentioned, acidic conditions may favour hydroxyl radical generation and consequently CYN oxidation. Although the positive effect of the high initial Fe(II) concentration on decreasing pH, the negative effect on hydroxyl radicals scavenging (Equation (4)) seems more significant.

Kinetic Assessment
During the Fenton process, H 2 O 2 reacts with Fe(II) to produce mainly hydroxyl radical, hydroperoxyl radical and high-valent iron complexes, which can oxidize organic and inorganic compounds [48,73].
In this study, the kinetic experiments were performed with excess Fenton reagents. The H 2 O 2 and Fe(II) concentrations at the optimal H 2 O 2 /Fe(II) molar ratio obtained from Phase 1 were respectively 500 and 1250 times greater than the initial CYN concentration. Due to the excess Fenton reagents, reaction order and rate constant were estimated from a pseudo reaction. The fitting of the kinetic models to the experimental data of one replicate is shown in Figure 4.
The kinetics parameters of the oxidation of CYN for each replicate are shown in Table 1. As shown in Figure 4 and based on R 2 (Table 1), CYN oxidation by the Fenton process was best described by the pseudo-first-order kinetic model. The results obtained from all three replicates showed a similar trend concerning fitting this kinetic model to the experimental data.
In this study, the kinetic experiments were performed with excess Fenton reagents. The H2O2 and Fe(II) concentrations at the optimal H2O2/Fe(II) molar ratio obtained from Phase 1 were respectively 500 and 1250 times greater than the initial CYN concentration. Due to the excess Fenton reagents, reaction order and rate constant were estimated from a pseudo reaction. The fitting of the kinetic models to the experimental data of one replicate is shown in Figure 4.  The kinetics parameters of the oxidation of CYN for each replicate are shown in Table  1. As shown in Figure 4 and based on R² (Table 1), CYN oxidation by the Fenton process was best described by the pseudo-first-order kinetic model. The results obtained from all   The rate constant for CYN obtained by Munoz and co-workers [64] is significantly higher than that obtained herein (1.233 × 10 −3 s −1 , Table 1). Likewise, the rate constant for MC-RR found by the same authors [64] is also considerably greater than that reported by Zhong and co-workers (2.165 × 10 −3 s −1 ) [61], who evaluated the degradation of 0.7 µM of MC-RR diluted in deionized-distilled water at pH 3 and using an excess of Fenton reagents (1500 µM of H 2 O 2 and 100 µM of Fe(II)).
The results obtained by Munoz and co-workers [64] may be attributed to the nanocatalyst itself, which was specially designed and boosted for the heterogeneous Fenton-like oxidation [74]. As nanocatalysts have high surface areas and low diffusional resistance, they are more efficient than conventional heterogeneous catalysts [75].
The observed differences in the apparent pseudo-first-order rate constants reflect the different radical generations in each process. It should be pointed out that higher apparent rate constants may indicate higher hydroxyl radical concentration since the hydroxyl radical concentration is incorporated in the apparent rate constant and/or higher susceptibility to hydroxyl radical oxidation.
Despite these differences, the apparent rate constant for CYN degradation found in the present study is in the same order of magnitude as that (4 × 10 −3 s −1 ) reported by Chen and co-workers [67] obtained by using UV-TiO 2 photocatalysis under the following conditions: 2.4 µM of initial CYN, 313 µM of TiO 2 , O 2 saturation, and 350 nm irradiation with an intensity of about 1.12 × 10 16 photons s −1 cm −3 .

Summary and Conclusions
The degradation of CYN standard in ultrapure water was investigated by means of the Fenton process. The results showed that the CYN removal increased as the H 2 O 2 /Fe(II) molar ratio decreased. Within the range of H 2 O 2 /Fe(II) molar ratio tested (0.4 to 4.0), the highest CYN degradation of 81% was obtained when H 2 O 2 /Fe(II) molar ratio was 0.4 (25 µM H 2 O 2 and 62.5 µM Fe(II)).
The increase of the dosage of Fenton reagents (50 µM H 2 O 2 and 125 µM Fe(II)) at the optimal H 2 O 2 /Fe(II) molar ratio of 0.4 resulted in an increase of the CYN oxidation efficiency to 91%. The CYN oxidation by the Fenton process followed a pseudo-first-order kinetic model with an apparent rate constant of 1.233 × 10 −3 s −1 .
Based on the results herein obtained, the Fenton process was effective for the removal of CYN from ultrapure water. Thus, the Fenton process seems to be a promising alternative for the CYN removal in drinking water treatment that could be easily implemented in fullscale worldwide since Fenton process is quite simple and highly cost-effective. However, further studies are necessary to evaluate matrix effects and analyze the feasibility and applicability of the Fenton process to treat natural water with high concentrations of CYN and much higher concentrations of hydroxyl radical scavenging compounds such as natural organic matter.
All solutions used in the experiments were prepared using ultrapure water (Milli-Q Reference water purification system, C79625, Merck Millipore, Darmstadt, Hesse, Germany).

Experimental Setup
Fenton experiments were performed in 250 or 500 mL borosilicate glass beaker batch reactors at room temperature (23 to 25 • C). The oxidation experiments were carried out with a CYN solution with initial concentration (C 0 ) of 0.05 µM prepared by diluting a CYN stock solution (0.12 µM) with ultrapure water. This solution will be referred to as "synthetic water". Oxidation reactions were started by adding to the synthetic water predetermined amounts of Fe(II), immediately followed by the addition of H 2 O 2 , under vigorous magnetic stirring. After the desired reaction time, a sodium sulfite solution (2 times stoichiometric excess of Na 2 SO 3 to H 2 O 2 [76]) was added to quench the residual H 2 O 2 , stopping the generation of hydroxyl radicals. The Fe(II), H 2 O 2 , and sodium sulfite stock solutions were always prepared fresh.
All of the experiments were carried out in triplicates. The synthetic water initial pH was adjusted to 5.0 ± 0.1 with 50 mM H 2 SO 4 and measured with a pH probe (Scientific Orion 3 Star portable pH meter, Thermo Fisher Scientific, Waltham, MA, USA).
The experimental setup can be divided into three phases ( Figure 5).  Figure 5). After that, similar experiments were performed in the second set, keeping fixed the initial Fe(II) concentration at 25 µM with initial H2O2 concentrations ranging from 10 to 100 µM (see Phase 1 orange boxes in Figure 5). The optimal H2O2/Fe(II) molar ratio was chosen based on the highest CYN degradation obtained from both sets of experiments. Additionally, In Phase 1, blank synthetic water was used to evaluate the degradation of CYN over the reaction time in the absence of Fenton reagents.
In Phase 2, experiments were conducted to evaluate the effect of the initial concentrations of H2O2 and Fe(II) on CYN degradation after a 30 min reaction time. These oxidation experiments were performed at initial concentrations of H2O2 and Fe(II) 0.4, 1, and 2 times the initial concentrations of the optimal H2O2/Fe(II) molar ratio obtained from Phase 1. Additionally, in Phase 2, the degradation of CYN over the reaction time was also evaluated using Fenton reagents (H2O2 and Fe(II)) separately at the highest concentrations tested in this study.  Figure 5). After that, similar experiments were performed in the second set, keeping fixed the initial Fe(II) concentration at 25 µM with initial H 2 O 2 concentrations ranging from 10 to 100 µM (see Phase 1 orange boxes in Figure 5). The optimal H 2 O 2 /Fe(II) molar ratio was chosen based on the highest CYN degradation obtained from both sets of experiments. Additionally, In Phase 1, blank synthetic water was used to evaluate the degradation of CYN over the reaction time in the absence of Fenton reagents.
In Phase 2, experiments were conducted to evaluate the effect of the initial concentrations of H 2 O 2 and Fe(II) on CYN degradation after a 30 min reaction time. These oxidation experiments were performed at initial concentrations of H 2 O 2 and Fe(II) 0.4, 1, and 2 times the initial concentrations of the optimal H 2 O 2 /Fe(II) molar ratio obtained from Phase 1. Additionally, in Phase 2, the degradation of CYN over the reaction time was also evaluated using Fenton reagents (H 2 O 2 and Fe(II)) separately at the highest concentrations tested in this study.

Detection and Quantification of H 2 O 2
The H 2 O 2 concentration was measured using the horseradish peroxidase (POD)-N,N-Diethyl-p-phenylenediamine (DPD) photometric method as described by Hahn and co-workers [77]. Hydrogen peroxide was measured immediately after the reaction time, withdrawing a sample from the reactor before adding the sodium sulfite solution.
In the analytical routine, a 13.5 mL aliquot of the oxidized synthetic water was transferred to a 50 mL beaker and, under magnetic stirring, 1.5 mL of a solution of 0.5 M Na 2 HPO 4 plus 0.5 M NaH 2 PO 4 was added. Right after that, 25 µL of 38.12 mM DPD solution (prepared in 50 mM H 2 SO 4 ) and 25 µL of 100 units mL −1 POD were added. The mixture was allowed to react for 40 s and then was transferred to a 5 cm path length quartz cuvette cell. The absorbance was measured at a wavelength of 551 nm using a UV-Vis spectrophotometer (DR 5000, Hach, Loveland, CO, USA).
For H 2 O 2 quantification, a 6-point calibration curve encompassing H 2 O 2 concentrations over the range of 0 to 10.29 µM was used. Samples were diluted using ultrapure water when their concentration was higher than the range of the calibration curve. The limit of detection (LoD) of 0.06 µM was determined according to Eurachem guidelines [78].

Detection and Quantification of Fe(II) and Total Iron
The concentrations of Fe(II) and total iron were measured by the ferrozine photometric method [79]. Similar to the hydrogen peroxide, residual Fe(II) and total iron were measured immediately after the reaction time.
Initially, to quantify residual Fe(II), a 0.3 mL of a 10 mM ferrozine solution (prepared in 0.1 M ammonium acetate) was added to a 2.7 mL sample of the oxidized synthetic water to form the Fe(II)-ferrozine complex whose absorbance can be measured at a wavelength of 562 nm using a UV-Vis spectrophotometer (DR 5000, Hach) employing 1 cm path length quartz cuvette cell.
Following the analytical routine, to quantify the total iron present, 0.45 mL of 1.4 M hydroxylamine hydrochloride (prepared in 2 M HCl) was added to a 2.4 mL aliquot of Fe(II)-ferrozine complex solution in order to reduce the Fe(III) to Fe(II) species. This mixture was allowed to react for ten minutes, and then 0.15 mL of 10 M ammonium acetate was added, and the absorbance of the resultant solution was also measured at a wavelength of 562 nm. The Fe(III) concentration was calculated as the difference between total iron and Fe(II) concentrations.
For Fe(II) and total iron quantifications, a 6-point calibration curve encompassing Fe(III) concentrations over the range of 0 to 6.72 µM was used. Samples were diluted using ultrapure water when their concentration was higher than the range of the calibration curve. The LoD of 0.61 µM for Fe(II) and 0.64 µM for total iron were determined according to Eurachem guidelines [78].

Detection and Quantification of CYN
Cylindrospermopsin was determined by high-performance liquid chromatography (Agilent 1200 Series, Agilent Technologies, Palo Alto, CA, USA) coupled to mass spectrometry (3200 QTRAP, Sciex, Toronto, ON, Canada) with an electrospray ion source operating in the positive mode, using N 2 as curtain (20 psi) and source gas (40 psi) under a capillary spray voltage of 5 kV at 450 • C. Separation from matrix interferents was performed using a Kromasil 100-5 C18 column (100 × 4.6 mm, 5 µm, Akzo Nobel, Bohus, Sweden), coupled to its corresponding guard column (3.0 × 4.6 mm, 5 µm) at room temperature (19 to 21 • C), using 0.15% (v/v) acetic acid solutions prepared in ultrapure water (A) and methanol (B) as mobile phase, at a flow rate of 0.55 mL min −1 . Gradient elution was achieved by increasing B from 10% (initial condition) to 30% in 0.5 min, to 90% in 7.5 min, held B constant for 2 min, and returning to the initial condition in 2 min. Under these conditions, CYN eluted at approximately 4.6 min.
For MS acquisition, a declustering potential of 56 V was applied to the orifice to prevent the ions from clustering together. Multiple reaction monitoring (MRM) was used for CYN detection and quantification through the monitoring of three precursor-toproduct ion transitions. The most intense one, at m/z 416.1 to 194.3 (43 eV CE), was used for quantification, while transitions at m/z 416.1 to 336.1 (29 eV CE) and 416.1 to 176.2 (45 eV CE) were used for confirmation purposes.
Quantification was performed by external calibration using a 6-point analytical curve encompassing CYN concentrations over the range of 2.41 nM to 0.12 µM. The LoD of 0.24 nM was determined according to Eurachem guidelines [78]. Since the LoD was quite low, sample extraction and extract concentration were not necessary for quantification of CYN.