Exploring PRISMA Scene for Fire Detection: Case Study of 2019 Bushﬁres in Ben Halls Gap National Park, NSW, Australia

: Precursore IperSpettrale della Missione Applicativa (Hyperspectral Precursor of the Application Mission, PRISMA) is a new hyperspectral mission by the ASI (Agenzia Spaziale Italiana, Italian Space Agency) mission launched in 2019 to measure the unique spectral features of diverse materials including vegetation and forest disturbances. In this study, we explored the potential use of this new sensor PRISMA for active wildﬁre characterization. We used the PRISMA hypercube acquired during the Australian bushﬁres of 2019 in New South Wales to test three detection techniques that take advantage of the unique spectral features of biomass burning in the spectral range measured by PRISMA. The three methods—the CO 2 -CIBR (continuum interpolated band ratio), HFDI (hyperspec-tral ﬁre detection index) and AKBD (advanced K band difference)—were adapted to the PRISMA sensor’s characteristics and evaluated in terms of performance. Classiﬁcation techniques based on machine learning algorithms (support vector machine, SVM) were used in combination with the visual interpretation of a panchromatic sharpened PRISMA image for validation. Preliminary analysis showed a good overall performance of the instrument in terms of radiance. We observed that the presence of the striping effect in the data can inﬂuence the performance of the indices. Both the CIBR and HFDI adapted for PRISMA were able to produce a detection rate spanning between 0.13561 and 0.81598 for CO 2 -CIBR and that between 0.36171 and 0.88431 depending on the chosen band combination. The potassium emission index turned out to be inadequate for locating ﬂaming in our data, possibly due to multiple factors such as striping noise and the spectral resolution (12 nm) of the PRISMA band centered at the potassium emission. 2500 ha, and is situated 60 km south-east of Tamworth and 10 km from the township of Nundle. The park is located at a comparatively high altitude that results in generally cool temperatures and high rainfall. Due to these characteristics, as reported in the BHGNP plan of management [24], wildﬁres were considered an unusual event at the time that plan was written; however, the simultaneous occurrence of high temperatures and wind speeds and low relative humidity that is required for high-intensity ﬁre behavior, conditions rare for this region, occurred in 2019. with central wavelengths located at 1646.9205 nm, 8,548,984 nm and 579.1278 nm shows a derived fire front extension of about


Introduction
Active wildfires are complex phenomena that involve heat transfer and high temperatures, peaking at around 1000 K for flaming and around 600 K for the smoldering phase [1,2]. Because of the high contrast with the ambient background temperature (300 K), most active fire remote-sensing applications rely on measurements of the Plankian thermal emission signature in the middle infrared (MIR) atmospheric window (3-5 µm), where solar radiation is lower than in the short-wave infrared (SWIR) window. Long-wavelength infrared (LWIR: 8-14 µm) regions can also be used to improve fire detection methods. [3].
Among other techniques, imaging spectroscopy in the visible and near-infrared (VNIR) and SWIR spectral ranges has been proved to have great potential for characterizing the fire disturbance continuum, which includes three phases: (1) pre-fire (fuel type and condition), (2) active fires (fire spread, intensity and emission) and (3) post-fire (burn severity) [4].
Several methods have been explored and tested for studying the pre-and post-fire phases [4] by using reflectance spectra, which highlight unique characteristics linked to the state of vegetation. For active fire characterization in the VNIR-SWIR hyperspectral range, [4,5] diverse aspects need to be considered. Because the data are generally acquired in the day time [4], to accurately detect a fire, the emitted radiance and reflected solar radiance background need to be properly separated. The spatial resolution of satellite

Case Study
To select the PRISMA hypercube, we searched the PRISMA catalogue [23] for images acquired in the eastern Australian seaboard between October 2019 and February 2020. We then selected the hypercube, acquired on 27 December 2020, in a cloud-free condition. The study was conducted on a subarea (region of interest (ROI)) of the hypercube with a size of 140 × 115 pixels and 212 bands depicting an active fire ( Figure 1b 2500 ha, and is situated 60 km south-east of Tamworth and 10 km from the township of Nundle. The park is located at a comparatively high altitude that results in generally cool temperatures and high rainfall. Due to these characteristics, as reported in the BHGNP plan of management [24], wildfires were considered an unusual event at the time that plan was written; however, the simultaneous occurrence of high temperatures and wind speeds and low relative humidity that is required for high-intensity fire behavior, conditions rare for this region, occurred in 2019. then selected the hypercube, acquired on 27 December 2020, in a cloud-free condition. The study was conducted on a subarea (region of interest (ROI)) of the hypercube with a size of 140 × 115 pixels and 212 bands depicting an active fire ( Figure 1b) in New South Wales about 250 km north of Sydney in the Ben Halls Gap National Park (BHGNP) which covers 2500 ha, and is situated 60 km south-east of Tamworth and 10 km from the township of Nundle. The park is located at a comparatively high altitude that results in generally cool temperatures and high rainfall. Due to these characteristics, as reported in the BHGNP plan of management [24], wildfires were considered an unusual event at the time that plan was written; however, the simultaneous occurrence of high temperatures and wind speeds and low relative humidity that is required for high-intensity fire behavior, conditions rare for this region, occurred in 2019.

PRISMA Sensor
The Hyperspectral Precursor of the Application Mission, PRISMA, was launched on 22 March 2019 on board the(Vettore Europeo di Generazione Avanzata) VEGA rocket. The mission has a capacity to acquire up to 223 images per day with a scene of 30 km × 30 km. Generally, the acquisition is based on a priority list and on-demand acquisition request.
The PRISMA imaging payload includes an imaging spectrometer (hyperspectral camera) with VNIR (visible and near-infrared) and SWIR (shortwave infrared) detectors and a panchromatic (PAN) camera detector. The imaging spectrometer provides a continuum of spectral bands spanning between 400 nm and 2500 nm at a ground-sampling distance (GSD) of 30 m/pixel ( Table 1). The PAN acquires the same area at 5 m/pixel.
The PRISMA hyperspectral instrument differs from previous space-imaging spectrometers because it uses an optical design based on a prism, rather than a grating, to obtain the dispersion of incoming radiation on a 2D focal plane. The advantages of prismbased spectrometers are their compact design and high efficiency [26]; the main disadvantage is the low dispersion [26]. The "instantaneous" spectral and spatial dimensions (across the track) of the PRISMA hyperspectral cube are directly determined by the 2D

PRISMA Sensor
The Hyperspectral Precursor of the Application Mission, PRISMA, was launched on 22 March 2019 on board the(Vettore Europeo di Generazione Avanzata) VEGA rocket. The mission has a capacity to acquire up to 223 images per day with a scene of 30 km × 30 km. Generally, the acquisition is based on a priority list and on-demand acquisition request.
The PRISMA imaging payload includes an imaging spectrometer (hyperspectral camera) with VNIR (visible and near-infrared) and SWIR (shortwave infrared) detectors and a panchromatic (PAN) camera detector. The imaging spectrometer provides a continuum of spectral bands spanning between 400 nm and 2500 nm at a ground-sampling distance (GSD) of 30 m/pixel ( Table 1). The PAN acquires the same area at 5 m/pixel.
The PRISMA hyperspectral instrument differs from previous space-imaging spectrometers because it uses an optical design based on a prism, rather than a grating, to obtain the dispersion of incoming radiation on a 2D focal plane. The advantages of prism-based spectrometers are their compact design and high efficiency [26]; the main disadvantage is the low dispersion [26]. The "instantaneous" spectral and spatial dimensions (across the track) of the PRISMA hyperspectral cube are directly determined by the 2D detectors, while the third dimension (along the track) is determined by the satellite motion (push broom) [27], to provide the 30 × 30 km scene.

PRISMA Scene
The PRISMA data are made available for free by the Italian Space Agency (ASI) [23,28]. The data are delivered in the HDF5 format with four options: (1) Level 1 (Hyperspectral/PAN) is radiometrically corrected and calibrated TOA (top of atmosphere) data; (2) Level 2B, the Geolocated at Ground Spectral Radiance Product (hyperspectral/PAN); (3) Level 2C, the Geolocated At-surface Reflectance Product (hyperspectral/PAN); and (4) Level 2D, a Geocoded version of the Level 2C product (hyperspectral/PAN). We used the LC1-PRISMA product acquired on 27 December 2019. The image processing was implemented by using the ENVI 5.5 (Harris Geospatial Solution, USA) software and consisted of three steps: (1) applying the scale factor 100 to convert the digital numbers of the L1 product to radiance expressed in Wm −2 sr −1 µm −1 [23,28]; (2) removing noisy bands and building the hyperspectral cube, by stacking the visible and SWIR data; (3) implementing the atmospheric correction and obtaining a reflectance spectrum; (4) producing spectral detection maps and implementing the code (in Matlab 2020b) for the semi-automatic processing of the CO 2 -CIBR and HDFI. The hypercube was visually explored to identify the noisy bands affecting the spectra; specifically, the bands within two VNIR spectral intervals (402.2041-426.7687 nm and 972.3630-959.4313 nm) and two SWIR intervals (942.8875-969.7985 nm and 2456.2781-2496.8254 nm) were removed. Because, in our data, the L2 PRISMA reflectance product showed several artifacts in the SWIR that would affect the classification, we preferred to derive the reflectance by applying atmospheric correction to the L1 PRISMA product.
The atmospheric correction was realized by using the QUAC (quick atmospheric correction) available in ENVI 5.5 and applied to the whole PRISMA scene. The QUAC was chosen for several reasons: (a) the image is cloud-free and no cloud shadows are in the scene, and it works best with scenes that contain diverse materials such as soil, vegetation and manmade structures [29], as in our case; (b) the full set of metadata that would be used to implement first-principles radiative-transfer modelling (i.e., fast line-ofsight atmospheric analysis of hypercubes, FLAASH) could not be found in our data; (c) [30] generally found that the results for QUAC were within ±15% of those for FLAASH. The QUAC returns apparent reflectance integer data, with pixel values ranging from 0 to 10,000 (representing 0 to 100% reflectance) [29]. Due to the PRISMA spectral characteristics, the near-shortwave infrared (NIR-SWIR) option available for QUAC was selected, and the pixel values were divided by 10,000 to obtain values spanning between 0 and 1.0 [29]. Figure 2a shows PRISMA single-pixel reflectance spectra corresponding to diverse categories in the imagery.
velop the CO2-CIBR metric, which turned out to be successful with both airborne (airborne visible/infrared imaging spectrometer, AVIRIS) and EO1-Hyperion data. The PRISMA fire radiance spectra were explored (an example of the spectra is shown in Figure 2b) to select the wavelengths to be used to calculate the CIBRs. The minimum absorption (λm) was found for bands centered at 2001.79 nm, 2010.36 nm, 2052.70 nm and 2061.09 nm. For the shoulders, the PRISMA bands centered at 1984.49 nm and 2035.94 nm were selected as λ2 and λ3, and those at 2035.94 nm and 2086.04 nm, as λ2 and λ3. The PRISMA central wavelengths and corresponding weighting factors that were used to calculate the CO2-CIBR are reported in Table 2.

Carbon Dioxide Continuum-Interpolated Band Ratio (CO 2 -CIBR)
The continuum-interpolated band ratio (CIBR) [2,31] can be used to separate the dominantly emitted radiance from the dominantly reflected radiance and is described by Metric (1).
where λ m is the wavelength at which the absorption is the strongest, λ 2 and λ 3 are the "shoulder" wavelengths with no absorption, and w2 and w3 are weighting factors, where w2 + w3 = 1 and w2 is given by (2).
For the carbon dioxide absorption features at 2010 nm were used by [2,6,10] to develop the CO 2 -CIBR metric, which turned out to be successful with both airborne (airborne visible/infrared imaging spectrometer, AVIRIS) and EO1-Hyperion data. The PRISMA fire radiance spectra were explored (an example of the spectra is shown in Figure 2b) to select the wavelengths to be used to calculate the CIBRs. The minimum absorption (λ m ) was found for bands centered at 2001.79 nm, 2010.36 nm, 2052.70 nm and 2061.09 nm. For the shoulders, the PRISMA bands centered at 1984.49 nm and 2035.94 nm were selected as λ 2 and λ 3 , and those at 2035.94 nm and 2086.04 nm, as λ 2 and λ 3 .
The PRISMA central wavelengths and corresponding weighting factors that were used to calculate the CO 2 -CIBR are reported in Table 2.

HFDI
The authors of [6,10] reported fire detection more accurate than that realized with the CIBR by using the hyperspectral fire detection index (HFDI), a normalized difference index defined as where L λ 1 and L λ 2 are the spectral radiances at two SWIR bands around 2430 nm and 2060 nm expressed in Wm −2 sr −1 µm −1 . These two bands provided better performance when using AVIRIS spectral data [6]. In addition, [10] highlighted that this metric needs to be adapted to the sensor noise level around the spectral range 2400-2500 nm. Because the PRISMA sensor is very new and its derived products are under continuous evaluation, we derived the HFDI for a series of band combinations following an approach similar to that used by [10] for EO1-Hyperion to identify the best combination.

Potassium Emission
Trace elements such as potassium, sodium and phosphorus [32][33][34] present in the biomass ionized at flaming temperatures emit signals at specific wavelengths that can be detected in the spectrum measured by a spectrometer [5,7,10]. These signals have been used to locate wildfire flaming phases using laboratory and airborne sensors [5,7]; their ability to be used to detect flaming from space [2,5,10] depending on a range of factors warrants further exploration [10]. Because the K emission lines occur at two specific wavelengths (766.5 nm and 769.9 nm) [7], two metrics were developed: (1) the K emission index [6,10], defined by the ratio of the radiances measured at the K emission wavelength (770 nm) and at the proximal band (780 nm), not influenced by the emission and acting as the background; (2) the AKBD metric, a normalized difference between the K emission bands and the background bands [5,10].

Fire Reference for Comparison
In order to compare the detection performance of the metrics, the fire pixels need to be discriminated from non-fire pixels. To do this, we applied a supervised classification to the reflectance PRISMA scene, to select endmembers (the truth to be used to train the classification algorithm). Specifically, we selected 48 pixels representing smoke, 48 pixels for the bare soil class (bare soil/road/anthropic), 36 pixels for vegetation (high vegetation, bushes and low vegetation), 12 pixels for freshly burned areas, and 48 pixels for active fires. Of the ground truth, 83% was used for the training, while the remaining 17% was selected for the classification validation. The pixels were selected by exploring the false color composite (Figure 1b) and looking at the PRISMA spectral profile, which was comparable with the corresponding classes that can be found in the literature [10,35]. In addition, pan sharpening was attempted to fuse a panchromatic-camera, 5 m-resolution PRISMA product and L2C PRISMA (VNIR-SWIR) projected product to obtain higher-resolution images, to be used for fire pixel validation. The data were fused using the Gram-Schmidt pan sharpening function available in ENVI 5.5, and although the L2D data were relatively noisy, they were used to visually confirm the burning areas. The classification was implemented by using the support vector machine (SVM) [36,37]. The SVM is considered, along with the random forest classifier and artificial neural networks, one of the most effective supervised classification methods [38] for multidimensional, large-scale image data. The SVM method algorithms perform well on noisy data and small numbers of training pixels [38,39], are suitable for anomaly detection [40] and are usually more accurate than other classification algorithms [37,41].
The kernel type was set as polynomial, with the value set to 2 and the penalty parameter set to 200. The result is showed in Figure 3b.
The kernel type was set as polynomial, with the value set to 2 and the penalty parameter set to 200. The result is showed in Figure 3b.
The overall classification accuracy was 96.87%, with a K coefficient of 0.96. The class fire, which is was of interest in this study, resulted in commission (false positive) and omission (false negative) error of 0%). Determining if there was good agreement with the other classes regarding this result was beyond the scope of this study. The classification was used to create a mask, with values equal to 1 corresponding to fire pixels and those equal to 0, the background (not burning pixels), for use in assessing the performance of the detection indices.

Fire Detection Analysis
The fire localization analysis was conducted for the three fire detection indices adapted to the PRISMA band features.
The detection rate was calculated by linear regression between the fire pixels derived by the specific indices and the ones resulting from the reference (the SVM-derived fire mask). A thresholding approach was used to identify the detected fire pixels. The cut-off ranges were obtained by automatically computing the minimum and maximum values for each index considering only pixels inside the "fire" class. (1) The cut-off minimum was obtained by subtracting two standard deviations (2σ) from the mean, and (2) the cut-off maximum, by adding one standard deviation (1σ) to the mean. The cut-off intervals were used to discriminate fire from background for each index frame.
The first index to be analyzed was the CO2-CIBR. Figure 4 shows the CO2-CIBR maps for the four band combinations. We can observe that, despite the striping noise, the front fire is recognizable. Specifically, it was better delineated when the absorption bands centered at 2001.79 nm and 2010.36 nm were used. The overall classification accuracy was 96.87%, with a K coefficient of 0.96. The class fire, which is was of interest in this study, resulted in commission (false positive) and omission (false negative) error of 0%).
Determining if there was good agreement with the other classes regarding this result was beyond the scope of this study. The classification was used to create a mask, with values equal to 1 corresponding to fire pixels and those equal to 0, the background (not burning pixels), for use in assessing the performance of the detection indices.

Fire Detection Analysis
The fire localization analysis was conducted for the three fire detection indices adapted to the PRISMA band features.
The detection rate was calculated by linear regression between the fire pixels derived by the specific indices and the ones resulting from the reference (the SVM-derived fire mask). A thresholding approach was used to identify the detected fire pixels. The cut-off ranges were obtained by automatically computing the minimum and maximum values for each index considering only pixels inside the "fire" class. (1) The cut-off minimum was obtained by subtracting two standard deviations (2σ) from the mean, and (2) the cut-off maximum, by adding one standard deviation (1σ) to the mean. The cut-off intervals were used to discriminate fire from background for each index frame.
The first index to be analyzed was the CO 2 -CIBR. Figure 4 shows the CO 2 -CIBR maps for the four band combinations. We can observe that, despite the striping noise, the front fire is recognizable. Specifically, it was better delineated when the absorption bands centered at 2001.79 nm and 2010.36 nm were used. Table 3 shows the results obtained in terms of the detection rate. A detection rate of 0.81 and a cut-off ranging between 0.550 and 0.74674 were determined for the CO 2 -CIBR having the minimum absorption band centered at 2001.36 nm, in agreement with the visual interpretation in Figure 4a.   Table 3 shows the results obtained in terms of the detection rate. A detection ra 0.81 and a cut-off ranging between 0.550 and 0.74674 were determined for the CO2-C having the minimum absorption band centered at 2001.36 nm, in agreement with the ual interpretation in Figure 4a.
Instead detection rate of 0.29 was obtained for the CO2-CIBR centered at 2010.36 very low compared to what was suggested by visual interpretation.
A low detection rate, consistent with the visual interpretation, was obtained fo other two CO2-CIBRs (Figure 4c,d). In these cases, the striping noise was relatively formly distributed and comparable with the signal. To mitigate the effect of the noise on the single bands [10], the mean value of the C CIBR indices was calculated. The result ( Figure 5) provides a cut-off of 0.7741 ± 0.1 well separated from the mean background value ( Figure 5).  A low detection rate, consistent with the visual interpretation, was obtained for the other two CO 2 -CIBRs (Figure 4c,d). In these cases, the striping noise was relatively uniformly distributed and comparable with the signal.
To mitigate the effect of the noise on the single bands [10], the mean value of the CO 2 -CIBR indices was calculated. The result ( Figure 5) provides a cut-off of 0.7741 ± 0.1091, well separated from the mean background value ( Figure 5).  The HFDI was retrieved by applying Equation (2) for the 24 possible band combinations ( Figure 6).  Table 4 reports the cut-off ranges and detection rates obtained for the 24 band combinations.
In this case, a bias value of 0.05 or 0.08 (Table 4) was added to the cut-off min in order to discriminate the "fire" from background. The results of the linear regression in terms of the detection rate are reported in Table 4. We can observe that nine HFDIs out of the 24 resulted in detection rates better than 0.76. The best performance was obtained by using the bands 2312.85 nm and 2061.08 nm, with a detection rate of 0.88. Twelve detection rates  Table 4 reports the cut-off ranges and detection rates obtained for the 24 band combinations.
Remote Sens. 2021, 13,1410  In this case, a bias value of 0.05 or 0.08 (Table 4) was added to the cut-off min in order to discriminate the "fire" from background. The results of the linear regression in terms of the detection rate are reported in Table 4. We can observe that nine HFDIs out of the 24 resulted in detection rates better than 0.76. The best performance was obtained by using the bands 2312.85 nm and 2061.08 nm, with a detection rate of 0.88. Twelve detection rates resulted in a "not a number" output.
To highlight the fire front, a mask was applied to the background (Figure 7).  The mean value of the HFDIs was calculated. The result provides a cut-off of 0.0778 ± 0.0265, well separated from the mean background value (Figure 8).   Finally, we calculated the potassium emission index by using the PRISMA band 44, centered at 770.25 nm (for the emission, Figure 9a) and the band 45 centered at 780.63 nm (for the background). The scatter plot obtained for the two bands shows a high correlation between the bands (Figure 9b). The results for the two indices are shown in Figure 9c,d. We can observe the prevalence of the striping effect over the signal. The fire is not recognizable when using the band ratio, and it is blurred and difficult to delineate when using the AKBD metric.

Discussion
We analyzed the three fire detection indices based on daytime acquisition by the new PRISMA sensor over the bushfires that occurred in Ben Halls Gap National Park in 2019. In our PRISMA subscene, both the CO2-CIBR and HFDI indices were able to discriminate

Discussion
We analyzed the three fire detection indices based on daytime acquisition by the new PRISMA sensor over the bushfires that occurred in Ben Halls Gap National Park in 2019. In our PRISMA subscene, both the CO 2 -CIBR and HFDI indices were able to discriminate the fire front. Regarding the CO 2 -CIBR, the best performance was obtained by using the band centered at 2001.79 nm (absorption) and those at 1984.49 nm and 2035.94 nm (the "shoulders"). However, when we look at the CO 2 -CIBR calculated with the PRISMA bands (2010. 36 nm, 1984.49 nm and 2035.94 nm) very close to the AVIRIS [10] ones (2010 nm, 1990 nm and 2040 nm), the obtained map (Figure 4b) and the detection rate (Table 3) look very different. The lower detection rate is due to the presence of a stripe whose values are comparable to those of fire. This needs to be further investigated in a range of PRISMA scenes.
The  [10] for the CO 2 -CIBR for EO1-Hyperion is interesting found.
The results obtained with the HFDI agree with the literature [10], which indicates that the HFDI should perform better than the CO 2 -CIBR. The best band combination turned out to be 2312.85 nm and 2061.08 nm, resulting in a detection rate of 0.88; this is very close to the AVIRIS one (2430 nm and 2061 nm) reported in [10]. When comparing the bestperforming EO1-Hyperion combinations used in [10] with the "almost" corresponding PRISMA combination, we obtained NaN. In Table 4, it is possible to observe how the cut-off ranges for these combinations are too narrow to permit a distinction between fire and background. Even looking at the single HFDI images in Figure 6, it is evident that, from the thirteenth combination onward, the front of the fire blends into the background.
The potassium (K)-emission-based index underperformed compared to the other two indices. Diverse aspects need to be considered to interpret this result. The full width half maximum (FWHM) of PRISMA in the used bands is 12.7 nm, so the separation is challenged compared to that for the ≤10 nm FWHM of EO1-Hyperion or AVIRIS [10]. Another effect to take into account is the striping effect present in our data that affects each band in a different way. This effect is stronger or weaker depending on the signal present in the image. For example, in an absorption band, all the signal is absorbed and the striping is imaged. The K emission band is very close to the O 2 absorption band centered at 765 nm, and it can be weakened by the two combined effects. Furthermore, the type of combustion (i.e., crown) as well as the vegetation type can contribute, as diverse vegetation species contain various amounts of K [33]. Finally, the presence of smoke can attenuate the signal [10] as well as the spatial resolution (30 m/px) [9] if only a fraction of the pixel is flaming.
In agreement with the literature for the EO1-Hyperion, our first results show that the HFDI performs better, in terms of fire detection, than the CO 2 -CIBR and AKBD. This is promising considering the difference in spectral resolution between PRISMA (~13 nm) and EO1-Hyperion (10 nm).
Future efforts should focus on the analysis of fires in diverse ecosystems (present in the scene or found in other PRISMA data), to determine if a common threshold can be found for retrieving the HFDI.

Conclusions
This study concerns a multimethod analysis for studying active land fires in New South West Australia that occurred during the 2019 bushfire season using hyperspectral techniques from space. We report the first case study of active fire characterization by using data from the new PRISMA space mission by the Italian Space Agency. The fire occurred in the Ben Halls Gap National Park during the bushfire season of 2019/2020 in Australia and was imaged by the PRISMA sensor. Firstly, we wanted to verify the ability of the PRISMA sensor to provide spectral features useful for characterizing phenomena, such as wildfires, different from those considered in its primary mission objectives; secondly, we tested three fire detection indices that relate the measured radiance to the intrinsic characteristics of the phenomena, such as the ionization of trace elements (AKBD index), carbon dioxide emissions (the CO 2 -CIBR index) and radiance values in the SWIR bands (HFDI).
The indices were adapted to PRISMA spectral features. Atmospheric correction was implemented to transform radiance into reflectance; a supervised classification, using the SVM approach, was used to retrieve the detection rate.
The obtained reflectance spectra are representative of diverse classes present in the scene. The overall performance of the instrument in terms of the radiance in our data was good. However, the presence of the striping effect can influence the performance of the indices.
In terms of the detection performance, the results agree with the literature to date [10]. In addition, PRISMA resulted in improved CO 2 -CIBR and HFDI performance compared to the EO1-Hyperion satellite [10].
The AKBD data resulted in underperformance. This is possibly due to multiple factors including the spectral resolution in the potassium band (12 nm), the striping noise, attenuation from the atmosphere and the spatial resolution.
The results are promising in terms of using PRISMA for active fire characterization using SWIR bands.
To close, it is relevant to mention that, due to the complexity of the hyperspectral sensors and the large number of data they collects, there is a gap between case studies and operational applications. In this context, synergies between future missions (i.e., EnMap, Chime, Surface Biology and Geology -SBG and Spaceborne Hyperspectral Applicative Land and Ocean Mission-SHALOM) and knowledge sharing will be very important for providing complementary information.  Data Availability Statement: PRISMA L1 and L2 data are available free of charge under PRISMA data license policy and can be accessed online at the official Italian Space Agency website www. prisma.asi.it, accessed on 4 February 2021. The added value dataset generated during the current study is available from the corresponding author upon reasonable request.