A Compressed and High-Accuracy Star Tracker with On-Orbit Deployable Bafﬂe for Remote Sensing CubeSats

: CubeSats have been widely used in remote sensing applications such as global coverage, hotspots revisited, etc. However, due to the strict size limitation, the high-accuracy measuring instruments such as star tracker are too large to be applied in CubeSat, thus causing insufﬁcient accuracy in satellite attitude and image positioning. In order to reduce the volume of star tracker without compromising the performance, the relationship between the volume and pointing accuracy or dynamic performance is studied and an optimization model of star tracker with a minimum volume is proposed. Compared with the traditional star tracker, a deployable star tracker with a novel deployable bafﬂe and surrounded circuit structure is designed. The bafﬂe consists of nested three-stage sub-bafﬂes with a scientiﬁcally analyzed and veriﬁed taper to achieve smooth deployment and compression. The special circuit structure surrounds the lens and can be compressed in the inner sub-bafﬂe. Therefore, the deployable star tracker can be compressed to the smallest volume and the sub-bafﬂes can be deployed to the accurate position without self-lock risk. The experimental results verify its deployment accuracy and reliability as well as space environmental adaptability. The deployable star tracker has almost the same results on stray light suppression ability, pointing accuracy (better than 3” ( 3 σ ) ) and dynamic performance (up to 3 ◦ /s) with the traditional star tracker. Furthermore, an integrated attitude determination and control system based on the deployable star tracker for CubeSat is further designed and implemented to support high-accuracy remote sensing.


Introduction
Satellite remote sensing images significantly contribute to the study of the relevant phenomena and changes in the earth's surface, such as agriculture or agronomy, geology, coast, oceanography, urban development, climate and the environment [1][2][3][4][5][6]. Due to the low cost [7], numerous CubeSats proposed by Stanford University [8] can compose a constellation to achieve global coverage and hotspots revisited. A growing number of technology companies launched CubeSats to provide low-cost remote sensing images of earth for scientific research. It is estimated that remote sensing applications have become the main sector of CubeSats, accounting for about 45% of all applications [9]. Planet company launched a large number of CubeSat groups to build a constellation photographing the earth with unprecedented frequency [10]. Other companies such as Aistech Space, SatRevolution, SpaceTY, etc., [11] have also launched CubeSats to provide remote sensing service in recent years. In general, the image positioning accuracy of CubeSat is always not high due to the limitation of the star tracker. The star tracker can provide the highest attitude accuracy of an arcsecond or even less [12,13] among all measurement devices of the satellite. However, high-accuracy star trackers are usually large in size with a total length well over 100 mm, which is the standard size constraint of 1U CubeSat. In addition, more than one star tracker with different directions is needed to ensure the high attitude accuracy for remote sensing satellites [14]. Therefore, it is difficult to use the star trackers in CubeSat.
In order to apply the high-accuracy star tracker in CubeSats, the volume of the star tracker must be reduced. Since the star tracker is mainly composed of baffle, lens and imaging system, the volume can be reduced from these three aspects. Firstly, the most direct method is to reduce the aperture and focal length of the lens and then the size of baffle and circuit will be reduced correspondingly. The star tracker ASTRO-15 [15] developed by the JenaOptronik company has an aperture of φ50 mm and focal length of 55 mm, for which its volume is up to φ192 mm × 552 mm with 25 • baffle. The star tracker ST-16 developed by the Sinclair Interplanetary company is widely used in CubeSats [16,17]. Compared with the ASTRO-15, the aperture and focal length of ST-16 are reduced to φ10 mm and 16 mm, respectively, so the volume of ST-16 is only φ90 mm × 120 mm with 22 • baffle and 62 mm × 56 mm × 38 mm without the baffle. It can be concluded that the baffle is an important factor leading to the enlargement of the star tracker's volume. However, the smaller the baffle, the more stray light will enter the optical system, which will have a serious impact on the star images and result in poor accuracy or malfunction of the star tracker. In order to reduce the volume of the star tracker baffle without affecting the stray light suppression ability, some techniques are proposed. In [18,19], a two-stage baffle is developed by setting a near hemisphere lens in front of the lens as an angle filtering method, which reduces the baffle's length to two-thirds of that of the traditional baffle. In [20], an inclined vanes baffle design method is proposed to reduce the volume of the baffle. Meanwhile, it also possesses better stray light suppression ability than traditional baffles. The aforementioned methods could not significantly reduce the volume of star tracker. In [21,22], a composed method of multiple small star tracker without the baffle for CubeSats is proposed, which renders at least two star trackers in CubeSats remain unaffected by sunlight at any time. This method abandons the baffle, but it also takes up a large volume due to the large number of star trackers needed in the given task. The last method is to reduce the volume of the imaging system, which includes an imaging detector and signal processing circuit. Charge coupled device (CCD) and CMOS image sensor (CIS) have been widely used for imaging detector. However, CISs are more popular than CCDs in space applications due to their superior radiation tolerance, lower power and smaller size. Benefitting from the back-illuminated stacked technology, the CISs can achieve higher sensitivity and lower noise with smaller pixel size in low-light conditions [23][24][25], which provides a method or possibility to reduce the volume of star tracker. However, the smaller the detector, the smaller the aperture and focal length of the lens, which may cause the accuracy and dynamic performance to decline. In conclusion, the aforementioned methods and techniques fail to balance the volume and accuracy of the star tracker perfectly.
In this paper, an on-orbit DST with small volume and high accuracy is proposed after analyzing the relationship between volume and accuracy or dynamic performance. The DST adopts the structure of three-stage deployable baffles with an analyzed and verified taper and the special surrounded circuit structure. Simulation and experiments show that the DST has a very small volume when compressed, which is theoretically independent of its baffle. The DST can accurately deploy the baffle without self-lock risk and even be deployed in extreme temperature. The deployable baffle has nearly the same excellent stray light suppression ability as the traditional baffle. Compared with the large TST, the proposed DST has almost the same accuracy (better than 3" (3σ)) under different incident angles of strong stray light and dynamic performance (up to 3 • /s).

The Difficulty and Solution for High-Accuracy Remote Sensing CubeSats
As shown in Figure 1a, the height of a high-accuracy (better than 3" (3σ)) and largevolume TST usually exceeds that of a 1U CubeSat and its volume also takes up a large space of the CubeSat, causing the CubeSat to have less space for other satellite components. For Remote Sens. 2021, 13, 2503 3 of 25 normal CubeSats, it is unnecessary to use high-accuracy star trackers. However, for remote sensing, the high-accuracy star tracker is required to realize high positioning accuracy for observed images. A star tracker usually consists of baffle, lens, imaging detector and its signal processing circuits. If the size of some parts is changed according to the overall size limit of CubeSat, the star tracker's accuracy and dynamic performance will be reduced.

The Difficulty and Solution for High-Accuracy Remote Sensing CubeSats
As shown in Figure 1a, the height of a high-accuracy (better than 3″ (3σ)) and largevolume TST usually exceeds that of a 1U CubeSat and its volume also takes up a large space of the CubeSat, causing the CubeSat to have less space for other satellite components. For normal CubeSats, it is unnecessary to use high-accuracy star trackers. However, for remote sensing, the high-accuracy star tracker is required to realize high positioning accuracy for observed images. A star tracker usually consists of baffle, lens, imaging detector and its signal processing circuits. If the size of some parts is changed according to the overall size limit of CubeSat, the star tracker's accuracy and dynamic performance will be reduced. It was observed that no matter how the parameters of star tracker are changed, its volume and accuracy will always be contradictory. Whether it comes to improving the accuracy or dynamic performance, the aperture of the lens must be increased. Figure 1b shows the relationship between the volume and the aperture.
Therefore, without decreasing the accuracy and dynamic performance of the star tracker, a deployable model for the star tracker is proposed, as shown in Figure 1c. On the one hand, the lens and imaging detector are not changed to theoretically render the DST to possess the same pointing accuracy and dynamic performance with TST. On the other hand, by using the deployable structure design, the technology of system-on-chip (SoC), the optimization of PCBs and the baffle of DST can be compressed and deployed. The volume of the electrical cabin can also be reduced. It should be explained that the power consumption of the proposed DST is very low (about 0.7 W) and so less heat will be produced. The heat will also be transferred to the satellite structure through the shell, which further reduces the temperature inside the DST. Additionally, the temperature changes of the lens can be corrected by on-orbit recalibration. Consequently, the proposed model can be adapted to minimize the size of the star tracker and make it related only to the lens.
Compared with TST, the proposed DST has similar accuracy under different incident angles of strong stray light, which is preferred 3" (3σ) with cross-boresight axis in Figure 1d. The product of an IADCS designed for CubeSat is shown in Figure 1e. The IADCS includes not only the basic components for attitude measurement and control but also two DSTs, which is incredible for traditional ADCS. When the CubeSat is with the IADCS in orbit, the DSTs will be deployed to provide the high-accuracy attitude data for CubeSat. Figure 2 shows the measuring principle of star tracker. When the star tracker is in a certain attitude matrix A in the celestial coordinate system, the navigation star s i can be measured by using the pinhole imaging principle. The direction vector corresponding to the celestial coordinate system is denoted as v i in Figure 2a. The direction vector in the star tracker coordinate system is w i , as shown in Figure 2b. where denotes the weighting coefficient and satisfies ∑ = 1. The optimal estimation, , of the star tracker attitude matrix in inertial space can be obtained.

The Analysis of Accuracy and Dynamic Performance
The key in achieving high-accuracy star tracker is the size of star spot on the detector. If the size of the star spot imaging on the detector occupies not less than 3 × 3 pixels, the star spot extraction accuracy, , can reach sub-pixel levels [28]. The constraint relationship between the accuracy index, , of star tracker and related optical parameters is described in Equation (4): The coordinate of the optical axis center on the detector is (x 0 , y 0 ). The coordinate of navigation star s i on the detector is (x i , y i ). Assume the focal length is f , the expression of the vector w i can be obtained [26] as Equation (1).
In the ideal case, the relationship can be expressed as the following equation.
When more than two stars are observed, the attitude matrix A of star tracker can be directly solved by quaternion optimal estimation QUEST [27] or other methods. The optimal attitude matrix A q can be obtained so that objective function J A q can reach the minimum value as is described in Equation (3): where α i denotes the weighting coefficient and satisfies ∑ n i=1 α i = 1. The optimal estimation, A q , of the star tracker attitude matrix in inertial space can be obtained.

The Analysis of Accuracy and Dynamic Performance
The key in achieving high-accuracy star tracker is the size of star spot on the detector. If the size of the star spot imaging on the detector occupies not less than 3 × 3 pixels, the star spot extraction accuracy, δ pix , can reach sub-pixel levels [28]. The constraint relationship between the accuracy index, α design , of star tracker and related optical parameters is described in Equation (4): where Figure 2c, α design , denotes the 3σ design accuracy and δ pix = 0.1l pix denotes the 0.1 pixel length of the detector. According to Equation (4), long focal length and small detector size will result in a small α, thus achieving high accuracy of the star tracker. However, changing the focal length will also affect the angle of field of view θ FOV . The mathematical expression of θ FOV is described as follows: where N pixel denotes the number of pixels in one direction of the detector. If the θ FOV is too small, the number of navigation stars in the field of view will be reduced to further decrease the accuracy of the star tracker. However, if the θ FOV is too large, too many navigation stars will be obtained and this affects the computing time of the processor. Therefore, the focal length and the detector size need to be balanced. However, the star spots imaging will be affected by many factors and mainly by spatial stray light and satellite dynamic rotation. As shown in Figure 3, spatial stray light and satellite rotation will separately cause star spots to be corrupted and observed to be trailing, thus leading to failure in obtaining star spot coordinates and further attitude problems. In order to achieve highly-accurate star spot extraction, it is necessary to ensure that stars can be imaged accurately. Therefore, the factors affecting star spot imaging should be analyzed.
where denotes the correction factor related to the lens, denotes the intensity of starlight, denotes the aperture of the lens and denotes the exposure time of the detector.
(a) (b) Due to sunlight and the earth-atmosphere light in space, the stray light will be imaged on the detector through the lens. The stray light can be regarded as a surface light source, then the average stray light energy, , received by a single pixel of the detector is approximately expressed as Equation (7) in the following: where denotes the correction coefficient related to the imaging system, ( ) denotes the stray light suppression rate of the baffle and denotes the luminance of stray light. In order to extract star spot coordinates from stray light, it is guaranteed that > .
When the satellite rotates, the star tracker will rotate at a certain angular velocity . At this time, the average star energy received by a single pixel of the detector can be expressed as Equation (8) in the following: where _ denotes the total energy on the detector, denotes the region of star spots imaging and denotes average star spot imaging width on the detector. In order to image the star spot at a higher angular velocity, it is known from Equation (8) that a decrease in exposure time is required to reduce the area of star spots imaging. However, the total energy received by the detector will also be decreased as the exposure time becomes smaller. Therefore, a larger lens aperture, , is needed to ensure the sufficient star energy.
Whatever the angular velocity, the energy of star spots is far less than that of stray light. If there is no baffle, the star spot would be corrupted by the stray light to further affect the star identification. Therefore, a baffle must be installed in front of the lens to It is assumed that the image size of a star spot is 3 × 3. The average star energy E 1 collected by a single pixel of star tracker detector can be expressed by Equation (6) in the following: where η 1 denotes the correction factor related to the lens, I star denotes the intensity of starlight, d denotes the aperture of the lens and t denotes the exposure time of the detector. Due to sunlight and the earth-atmosphere light in space, the stray light will be imaged on the detector through the lens. The stray light can be regarded as a surface light source, then the average stray light energy, E 2 , received by a single pixel of the detector is approximately expressed as Equation (7) in the following: where η 2 denotes the correction coefficient related to the imaging system, ξ (θ) denotes the stray light suppression rate of the baffle and B sl denotes the luminance of stray light. In order to extract star spot coordinates from stray light, it is guaranteed that E 1 > E 2 . When the satellite rotates, the star tracker will rotate at a certain angular velocity ω sat . At this time, the average star energy E 3 received by a single pixel of the detector can be expressed as Equation (8) in the following: where E 3_total denotes the total energy on the detector, A star denotes the region of star spots imaging and N denotes average star spot imaging width on the detector. In order to image the star spot at a higher angular velocity, it is known from Equation (8) that a decrease in exposure time is required to reduce the area of star spots imaging. However, the total energy received by the detector will also be decreased as the exposure time becomes smaller. Therefore, a larger lens aperture, d, is needed to ensure the sufficient star energy. Whatever the angular velocity, the energy of star spots is far less than that of stray light. If there is no baffle, the star spot would be corrupted by the stray light to further affect the star identification. Therefore, a baffle must be installed in front of the lens to suppress the stray light. The baffle design for length and outer aperture diameter is shown  Figure 4. According to the geometric principle of the baffle design, the length of the baffle is calculated as described in Equation (9): where ψ denotes the earth aspect angle of the baffle to prevent weak stray light, especially the earth-atmosphere light, from entering the aperture directly and ϑ = 0.5 θ FOV denotes the half-FOV angle of the star tracker. The calculation of the outer aperture, D, of the baffle can be expressed as Equation (10) combined with Equation (9).
Remote Sens. 2021, 13, x FOR PEER REVIEW 7 of 25 suppress the stray light. The baffle design for length and outer aperture diameter is shown in Figure 4. According to the geometric principle of the baffle design, the length of the baffle is calculated as described in Equation (9): where denotes the earth aspect angle of the baffle to prevent weak stray light, especially the earth-atmosphere light, from entering the aperture directly and = 0.5 denotes the half-FOV angle of the star tracker. The calculation of the outer aperture, , of the baffle can be expressed as Equation (10)   As shown in Figure 5, when the earth aspect angle is fixed, the length of the baffle and the outer aperture will increase with increased half-FOV angle. When the half-FOV angle is fixed, the ability of the star tracker to suppress stray light is enhanced but the baffle length and the outer aperture increase with the decreased earth aspect angle. Therefore, the TST usually has a longer baffle due to the small earth aspect angle.  As shown in Figure 5, when the earth aspect angle is fixed, the length of the baffle and the outer aperture will increase with increased half-FOV angle. When the half-FOV angle is fixed, the ability of the star tracker to suppress stray light is enhanced but the baffle length and the outer aperture increase with the decreased earth aspect angle. Therefore, the TST usually has a longer baffle due to the small earth aspect angle. suppress the stray light. The baffle design for length and outer aperture diameter is shown in Figure 4. According to the geometric principle of the baffle design, the length of the baffle is calculated as described in Equation (9): where denotes the earth aspect angle of the baffle to prevent weak stray light, especially the earth-atmosphere light, from entering the aperture directly and = 0.5 denotes the half-FOV angle of the star tracker. The calculation of the outer aperture, , of the baffle can be expressed as Equation (10)   As shown in Figure 5, when the earth aspect angle is fixed, the length of the baffle and the outer aperture will increase with increased half-FOV angle. When the half-FOV angle is fixed, the ability of the star tracker to suppress stray light is enhanced but the baffle length and the outer aperture increase with the decreased earth aspect angle. Therefore, the TST usually has a longer baffle due to the small earth aspect angle.  According to the structure of the star tracker and combining Equations (9) and (10), the theoretical volume of the TST can be expressed in Equation (11) as follows: where F lens denotes the F-number of lens, k d denotes the ratio between the manufacturing diameter and the outer aperture diameter and k f −TST denotes the coefficient describing the relationship between the focal length and the length of the electronic cabin. It is obvious from the Equation (11) that the volume of traditional star tracker is cubic with the aperture of the lens.
To sum up, as is shown Figure 6, improving the pointing accuracy and dynamic performance of the star tracker will increase the aperture, which will further increase the length of the baffle and eventually increase the volume of the star tracker. If the volume of the baffle can be compressed by using an optimization model according to Equation (11), the length of the star tracker will be independent of the baffle no matter how the aperture is increased. According to the structure of the star tracker and combining Equations (9) and (10), the theoretical volume of the TST can be expressed in Equation (11) as follows: where denotes the F-number of lens, denotes the ratio between the manufacturing diameter and the outer aperture diameter and denotes the coefficient describing the relationship between the focal length and the length of the electronic cabin. It is obvious from the Equation (11) that the volume of traditional star tracker is cubic with the aperture of the lens.
To sum up, as is shown Figure 6, improving the pointing accuracy and dynamic performance of the star tracker will increase the aperture, which will further increase the length of the baffle and eventually increase the volume of the star tracker. If the volume of the baffle can be compressed by using an optimization model according to Equation (11), the length of the star tracker will be independent of the baffle no matter how the aperture is increased.

Structure Design and Volume Analysis
The biggest difference between the DST and the TST is the deployable baffle structure. Given the aperture of lens and the half-FOV, the theoretical length of the baffle and the outer aperture can be calculated. The baffle of DST is divided into sub-baffles with different diameters by the vanes based on the geometrograph method [29]. Therefore, each sub-baffle can be nested with one another to achieve deployment and compression. The design method of deployable baffle is as follows.
In Figure

Structure Design and Volume Analysis
The biggest difference between the DST and the TST is the deployable baffle structure. Given the aperture of lens and the half-FOV, the theoretical length of the baffle and the outer aperture can be calculated. The baffle of DST is divided into sub-baffles with different diameters by the vanes based on the geometrograph method [29]. Therefore, each subbaffle can be nested with one another to achieve deployment and compression. The design method of deployable baffle is as follows.
In Figure Remote Sens. 2021, 13, x FOR PEER REVIEW 9 of 25 Point must satisfy Equation (13) to cancel the third vane.
Each designed sub-baffle sidewall is different from the traditional baffle, which has a certain taper . The three important deployable baffle position parameters (point C, G and F) can be derived by Equation (12). Equation (14) represents the coordinates of point ( , ).
Equation (16) represents the coordinates of point ( , ) in the following: Point H must satisfy Equation (13) to cancel the third vane.
Each designed sub-baffle sidewall is different from the traditional baffle, which has a certain taper α. The three important deployable baffle position parameters (point C, G and F) can be derived by Equation (12). Equation (14) represents the coordinates of Equation (15) represents the coordinates of point G(x G , y G ).
Equation (16) represents the coordinates of point F(x F , y F ) in the following: where ω denotes the sun aspect angle, L denotes the theoretical length of the baffle and D denotes the diameter of the outer aperture.
Any sub-baffle is independent with one another and driven by the springs. The springs are placed between the sub-baffles, as shown in Figure 8. The sub-baffles can be compressed by the external binding device and the springs are compressed between the sub-baffles. When the binding device is released, the sub-baffles will pop out and be deployed by the drive of the springs.
where denotes the sun aspect angle, denotes the theoretical length of the baffle and denotes the diameter of the outer aperture.
Any sub-baffle is independent with one another and driven by the springs. The springs are placed between the sub-baffles, as shown in Figure 8. The sub-baffles can be compressed by the external binding device and the springs are compressed between the sub-baffles. When the binding device is released, the sub-baffles will pop out and be deployed by the drive of the springs. As shown in Figure 8a, each sub-baffle is divided into main body part and connection part , = 1,2,3.
is used to prevent the sub-baffle from being deployed excessively. As shown in Figure 8b, can make each sub-baffle coincide with the bottom to improve the stability after compression. The diameter and height of and must satisfy the constraint given by Equation (17) in the following: As shown in Figure 8a, each sub-baffle is divided into main body part A i and connection part B i , i = 1, 2, 3. B i is used to prevent the sub-baffle from being deployed excessively. As shown in Figure 8b, B i can make each sub-baffle coincide with the bottom to improve the stability after compression. The diameter and height of A i and B i must satisfy the constraint given by Equation (17) in the following: where α denotes the taper of the sub-baffle wall, D i denotes the inner diameter for the big end of A i , d i denotes the inner diameter for the small end of A i , H i denotes the distance between adjacent sub-baffle in the deployable state, D Bi = D i−1 denotes the inner diameter of the big end of B i , d Bi denotes the inner diameter of the small end of B i and p i denotes the contact length between B i and A i−1 .
The most important parameters of the deployable baffle are the diameter and length of each sub-baffle. The structural parameters of A i satisfies the constraint as described in Equation (18): T denotes design the parameter of deployable baffle and ϕ denotes the deign matrix of deployable baffle as is shown in Equation (19).
To ensure that the D Bi of each sub-baffle can come into contact with the bottom surface due to the springs, each sub-baffle needs to satisfy the constraint as described in Equation (20) in the compressed state: where L M denotes the height of the lens mount, h i denotes the distance between adjacent sub-baffle in the suppression state, l i denotes the length of B i , l i = l xi + l yi , l xi denotes the length of B i with each sub-baffle and l yi is used to ensure that the bottom end of B i coincides with the bottom, respectively. In the actual mechanical design and processing, h i could be short by the design. When the signal processing circuit PCBs are complex, the PCBs are surrounded outside the lens to make full use of the space, as shown in Figure 8. Moreover, using SoC technology for signal processing can further reduce the number of circuit PCBs. Under the extreme and ideal conditions, the deployable length L d and compressed length L c of the deployable star tracker can be expressed as described in Equation (21): where k f is similar to k f −TST in describing the DST. Combining with Equations (9) and (10), the volume of DST under deployable state and compressed state can be expressed as described in Equation (22).
The volume ratio κ of compression to deployment is as described in Equation (23).
Therefore, compared with the TST, the DST can effectively reduce its volume in a special manner.

Analysis of Reliability
When the baffle is being deployed, the deploying time of the same sub-baffle with different edges may be different. The springs will be deformed so that the driving force is not along the optical axis. No matter how much driving force the springs produce, the sub-baffles cannot continue in its deployment, which is named as the baffle self-lock phenomenon. In order to solve the self-lock problem, it is assumed that the sub-baffle i inclines for some reason during the deployment with β angle relative to the sub-baffle i − 1. Additionally, it is assumed that the spring driving force T is along the optical axis of the sub-baffle i and the stress model of the sub-baffle is shown in Figure 9.
Therefore, compared with the TST, the DST can effectively reduce its volume in a special manner.

Analysis of Reliability
When the baffle is being deployed, the deploying time of the same sub-baffle with different edges may be different. The springs will be deformed so that the driving force is not along the optical axis. No matter how much driving force the springs produce, the sub-baffles cannot continue in its deployment, which is named as the baffle self-lock phenomenon. In order to solve the self-lock problem, it is assumed that the sub-baffle inclines for some reason during the deployment with angle relative to the sub-baffle − 1. Additionally, it is assumed that the spring driving force is along the optical axis of the sub-baffle and the stress model of the sub-baffle is shown in Figure 9. When the sub-baffle is stationary, the stress relationship is as described in Equation (24): where and denote the friction force on the upper and lower edge of the sub-baffle as Figure 9. The definition of friction is given by = and = (μ is the friction coefficient between the sub-baffle). and are the positive pressures of the subbaffle on the upper and lower edge of the sub-baffle − 1, respectively. and are the positive pressures of the sub-baffle − 1 on the upper and lower edge of the subbaffle , respectively. According to the geometric relationship of the force, Equation (25) can be derived.
Combined with Equations (24) and (25), the critical condition of self-lock can be derived as Equation (26). When the sub-baffle i is stationary, the stress relationship is as described in Equation (24): where f 1 and f 2 denote the friction force on the upper and lower edge of the sub-baffle i as Figure 9. The definition of friction is given by f 1 = µN 1 and f 2 = µN 2 (µ is the friction coefficient between the sub-baffle).
Combined with Equations (24) and (25), the critical condition of self-lock can be derived as Equation (26).
Therefore, in order to prevent the self-lock during deployment, the taper and friction coefficient of the sub-baffle must satisfy tanα > µ, which can be considered to possess high reliability.

Analysis of Deployment Accuracy
The inclination between sub-baffles may occur after deployment because the spring force is not completely along the optical axis. If the adjacent sub-baffle inclines after full deployment, the imaging and stray light suppression ability for the star tracker will be affected due to the incorrect position of the sub-baffles.
In the worst case, with a force perpendicular to the sidewall in the deployable state, the fit clearance error in the manufacturing process will cause the relative inclination of adjacent sub-baffle. The material of the baffle will deform to cause further inclination. It is assumed that the fit clearance between adjacent sub-baffle is ∆m ≥ 0 and the adjacent sub-baffles are inclined relatively under the action of external forces as shown in Figure 10.
= (26) Therefore, in order to prevent the self-lock during deployment, the taper and friction coefficient of the sub-baffle must satisfy > , which can be considered to possess high reliability.

Analysis of Deployment Accuracy
The inclination between sub-baffles may occur after deployment because the spring force is not completely along the optical axis. If the adjacent sub-baffle inclines after full deployment, the imaging and stray light suppression ability for the star tracker will be affected due to the incorrect position of the sub-baffles.
In the worst case, with a force perpendicular to the sidewall in the deployable state, the fit clearance error in the manufacturing process will cause the relative inclination of adjacent sub-baffle. The material of the baffle will deform to cause further inclination. It is assumed that the fit clearance between adjacent sub-baffle is Δ ≥ 0 and the adjacent sub-baffles are inclined relatively under the action of external forces as shown in Figure  10. If the fit clearance satisfies Δ = 0, it must be considered that the angle between the sub-baffle and the radius of the rotating circle is greater than 90°. Otherwise, the subbaffles would also be inclined under Δ = 0. Therefore, the contact length must satisfy Equation (27).

> (27)
If Equation (27) is satisfied, it can ensure zero inclination when achieving full deployment without applying force. Only when this condition is satisfied will the influence of the fit clearance Δ on the inclination be considered.
When the fit clearance satisfies Δ > 0 and Equation (27), respectively, the sub-baffle inclines relative to the sub-baffle − 1 under the action of external force as shown in Figure 10b. In triangle ACG, Equation (28) can be derived by the cosine theorem described as follows: If the fit clearance satisfies ∆m = 0, it must be considered that the angle between the sub-baffle and the radius of the rotating circle is greater than 90 • . Otherwise, the sub-baffles would also be inclined under ∆m = 0. Therefore, the contact length p i must satisfy Equation (27).
If Equation (27) is satisfied, it can ensure zero inclination when achieving full deployment without applying force. Only when this condition is satisfied will the influence of the fit clearance ∆m on the inclination be considered.
When the fit clearance satisfies ∆m > 0 and Equation (27), respectively, the sub-baffle i inclines relative to the sub-baffle i − 1 under the action of external force as shown in Figure 10b. In triangle ACG, Equation (28) can be derived by the cosine theorem described as follows: where S denotes the length of line CG, R denotes the length of line AG and AC, ∆ = R (D+∆m) ∆m denotes the length of line BC and β is angle of CAF. Therefore, the S is derived as described in Equation (29). The maximum inclination angle γ i can be derived as described in Equation (30).
To simplify the expression of γ i , the R and β must be reduced. In triangle ACF, the Equation (31) can be derived by the sine theorem.
Therefore, sinβ and cosβ can be derived as described by Equation (32).
In triangle ACF, the Equation (33) can be derived by the cosine theorem.
The total maximum inclination angle γ of the three-stage sub-baffle relative to the lens center is described in Equation (38).
With the external force, the three sub-baffles can be regarded as interference joints when the fit clearance satisfies ∆m = 0. The whole deployable baffle can be regarded as a rigid body and cantilever structure. When the fit clearance satisfies ∆m > 0, the three sub-baffles will incline first. Then the material deformation occurs and each sub-baffle can be regarded as a cantilever structure separately. Due to the irregular shape of the sub-baffles, the finite element method (FEM) software will be used to analyze the material deformation of the deployable baffle under the two fit conditions. Table 1 lists the key values related to the volume ratio and the calculated ratio values according to the Equation (22). Due to the requirements of manufacturing technology and space radiation protection, the length of the deployable baffle with a small focal length after compression cannot be completely ignored. Therefore, the real volume ratio κ real is slightly larger than the κ ideal . If the focal length is larger, then the two values of volume ratio will be closer. The DST can be smaller and closer to the volume limitation by optimizing the structure in the future.

Deployment Accuracy and Reliability
The deployment accuracy of the DST is mainly affected by the inclination and material deformation of the sub-baffles. The relevant design parameters of the practical DST are shown in Table 2. It is explained that the simulations are based on the parameters of practical DST. The relationship between the relative maximum inclination angle and the clearance for each sub-baffle of the proposed DST is calculated by Equation (34), as shown in Figure 11. The simulation results show that the relative maximum inclination angle between the sub-baffles can be greatly reduced with the smaller clearance value. Table 1 lists the key values related to the volume ratio and the calculated ratio values according to the Equation (22). Due to the requirements of manufacturing technology and space radiation protection, the length of the deployable baffle with a small focal length after compression cannot be completely ignored. Therefore, the real volume ratio κ is slightly larger than the κ . If the focal length is larger, then the two values of volume ratio will be closer. The DST can be smaller and closer to the volume limitation by optimizing the structure in the future.

Deployment Accuracy and Reliability
The deployment accuracy of the DST is mainly affected by the inclination and material deformation of the sub-baffles. The relevant design parameters of the practical DST are shown in Table 2. It is explained that the simulations are based on the parameters of practical DST. The relationship between the relative maximum inclination angle and the clearance for each sub-baffle of the proposed DST is calculated by Equation (34), as shown in Figure  11. The simulation results show that the relative maximum inclination angle between the sub-baffles can be greatly reduced with the smaller clearance value. As shown in Figure 12, the material deformation analysis with ∆m = 0 and ∆m = 0.1 mm after deployment of the practical DST is realized by the FEM software, ANSYS. A vertical force of 100 Mpa is applied to the edge of the third sub-baffle. The relevant simulation parameters and results are shown in Table 3. The simulation results show that the material deformation can be ignored because the values of two ∆m are both less than 1 mm. Therefore, for the sake of deployment accuracy, only the influence of inclination for sub-baffles needs to be considered. mm. Therefore, for the sake of deployment accuracy, only the influence of inclination for sub-baffles needs to be considered.  In order to avoid self-lock, the taper of the designed sub-baffles must satisfy α > 2.86° as described in Equation (26) by polytetrafluoroethylene (PTFE) with = 0.05. The practical design of the sub-baffles has a taper of 4°. However, by conducting deployment experiments 50 times for the practical DST without PTFE as shown in Figure 13, the experimental results show that each sub-baffle can be deployed to the appropriate position without self-lock and the average height error of the DST is 0.0284 mm within the allowable error range. Therefore, the inclination between adjacent sub-baffles can be approximately ignored.  In order to avoid self-lock, the taper of the designed sub-baffles must satisfy α > 2.86 • as described in Equation (26) by polytetrafluoroethylene (PTFE) with µ = 0.05. The practical design of the sub-baffles has a taper of 4 • . However, by conducting deployment experiments 50 times for the practical DST without PTFE as shown in Figure 13, the experimental results show that each sub-baffle can be deployed to the appropriate position without self-lock and the average height error of the DST is 0.0284 mm within the allowable error range. Therefore, the inclination between adjacent sub-baffles can be approximately ignored.

Environmental Adaptability
The space temperature will be extreme when the DST is deploying. The deploying device system requires heat to release the sub-baffles. It is necessary to consider whether the DST can be deployed at extremely low temperatures. Thus, ten experiments were carried out at extremely low temperatures (−40 • C) and room temperature (25 • C), respectively. The experiment results show that the DST can be deployed at extremely low temperature, which takes t −40 • C = 243.6 s from the moment of sending the deployment command to full deployment. However, it only takes t 25 • C = 32.3 s at room temperature. Although the deployment time of the DST at extremely low temperatures is much longer than that at room temperature, it proves that the deployable baffle can finally be deployed in space environment. Remote Sens. 2021, 13, x FOR PEER REVIEW 17 of 25 Figure 13. The practical deployment height of the deployable baffle at 50 times experiment.

Environmental Adaptability
The space temperature will be extreme when the DST is deploying. The deploying device system requires heat to release the sub-baffles. It is necessary to consider whether the DST can be deployed at extremely low temperatures. Thus, ten experiments were carried out at extremely low temperatures (−40 ℃) and room temperature (25 ℃), respectively. The experiment results show that the DST can be deployed at extremely low temperature, which takes ̅ ℃ = 243.6 s from the moment of sending the deployment command to full deployment. However, it only takes ̅ ℃ = 32.3 s at room temperature. Although the deployment time of the DST at extremely low temperatures is much longer than that at room temperature, it proves that the deployable baffle can finally be deployed in space environment.
Due to the satellite attitude, the top and circumferential direction of the star tracker will be directly illuminated by the sun during a certain period of time after the satellite enters the sunlight area. If the black anodizing process is adopted, the sun absorption rate of the baffle is high and the temperature will rise rapidly. After entering the shadow area, the temperature will decrease rapidly, resulting in a great temperature fluctuation. In practical satellite applications, as shown in Figure 14, silvered fluorinated ethylene propylene film (also known as F46/Ag film) is pasted on the surface of the deployable baffle because it has much lower sun absorptance. Due to the satellite attitude, the top and circumferential direction of the star tracker will be directly illuminated by the sun during a certain period of time after the satellite enters the sunlight area. If the black anodizing process is adopted, the sun absorption rate of the baffle is high and the temperature will rise rapidly. After entering the shadow area, the temperature will decrease rapidly, resulting in a great temperature fluctuation. In practical satellite applications, as shown in Figure 14, silvered fluorinated ethylene propylene film (also known as F46/Ag film) is pasted on the surface of the deployable baffle because it has much lower sun absorptance.

Environmental Adaptability
The space temperature will be extreme when the DST is deploying. The deploying device system requires heat to release the sub-baffles. It is necessary to consider whether the DST can be deployed at extremely low temperatures. Thus, ten experiments were carried out at extremely low temperatures (−40 ℃) and room temperature (25 ℃), respectively. The experiment results show that the DST can be deployed at extremely low temperature, which takes ̅ ℃ = 243.6 s from the moment of sending the deployment command to full deployment. However, it only takes ̅ ℃ = 32.3 s at room temperature. Although the deployment time of the DST at extremely low temperatures is much longer than that at room temperature, it proves that the deployable baffle can finally be deployed in space environment.
Due to the satellite attitude, the top and circumferential direction of the star tracker will be directly illuminated by the sun during a certain period of time after the satellite enters the sunlight area. If the black anodizing process is adopted, the sun absorption rate of the baffle is high and the temperature will rise rapidly. After entering the shadow area, the temperature will decrease rapidly, resulting in a great temperature fluctuation. In practical satellite applications, as shown in Figure 14, silvered fluorinated ethylene propylene film (also known as F46/Ag film) is pasted on the surface of the deployable baffle because it has much lower sun absorptance. According to the mass and heat capacity of the satellite as shown in Figure 14, Table 4 shows the results of temperature changes relative to whether or not the DST has F46/Ag film pasted in an orbital cycle. The F46/Ag film can greatly reduce the influence of the sun on DSTs, rendering the DSTs with better environmental adaptability. Table 4. The temperature changes of black anodizing process and F46/Ag film in an orbital cycle.

Index
Black Anodizing F46/Ag Film

Stray Light Suppression Ability
For the DST, the deployable structure does not affect its optical performance. The point light transmittance (PST) is usually used to measure the ability of the baffle to suppress stray light. The PST is defined as the ratio of the illuminance E o (θ) generated on the imaging surface of the optical detector and the illuminance E i (θ) on the input aperture perpendicular to the point source as described in Equation (31), when a light source with an off-axis angle of θ passes through the optical system.
For the star tracker, the illuminance of the sunlight at the entrance of the baffle is constant except in the shadow areas of Earth. The simulation results of the deployable baffle and the traditional baffle with the same optical parameters are shown in Figure 15. The optical absorbance of the coating material on the inner surface is set to 95%. The design sunlight suppression angle is 28 • .
on DSTs, rendering the DSTs with better environmental adaptability.

Stray Light Suppression Ability
For the DST, the deployable structure does not affect its optical performance. The point light transmittance (PST) is usually used to measure the ability of the baffle to suppress stray light. The PST is defined as the ratio of the illuminance ( ) generated on the imaging surface of the optical detector and the illuminance ( ) on the input aperture perpendicular to the point source as described in Equation (31), when a light source with an off-axis angle of passes through the optical system.
For the star tracker, the illuminance of the sunlight at the entrance of the baffle is constant except in the shadow areas of Earth. The simulation results of the deployable baffle and the traditional baffle with the same optical parameters are shown in Figure 15. The optical absorbance of the coating material on the inner surface is set to 95%. The design sunlight suppression angle is 28°. The simulation results show that the stray light suppression ability of the deployable baffle is as good as a traditional baffle. In order to achieve the practical PST performance of the baffle, an experiment was carried out, as shown in the Figure 16a. The ultrablack The simulation results show that the stray light suppression ability of the deployable baffle is as good as a traditional baffle. In order to achieve the practical PST performance of the baffle, an experiment was carried out, as shown in the Figure 16a. The ultrablack film with absorbance up to 95% is coated on the inner surface of sub-baffles. The practical DST was rotated to create a certain angle with the fixed sun simulator to simulate the stray light incident angle. The stray light incident angle is set to 28 • to 60 • (interval of 2 • ). At different stray light incident angles, the average background gray values of the 1000 images are recorded, respectively.
According to the average gray values of the images under different sun incident angles, the normalized test result of PST was achieved and the simulation result was also normalized as Figure 16b. The experiment results possess a similar curve as the simulations, which means the deployable baffle has good stray light suppression ability.
stray light incident angle. The stray light incident angle is set to 28° to 60° (interval of 2°). At different stray light incident angles, the average background gray values of the 1000 images are recorded, respectively.
According to the average gray values of the images under different sun incident angles, the normalized test result of PST was achieved and the simulation result was also normalized as Figure 16b. The experiment results possess a similar curve as the simulations, which means the deployable baffle has good stray light suppression ability.

Accuracy and Dynamic Performance
As shown in Figure 16a, in order to acquire the accuracy of star trackers at different sun incident angles, the 1000 quaternion data are calculated by the star tracker in real time at each sun incident angle. Due to the weather, only 32° to 60° experimental data are adopted. According to the quaternion differential equation as described in Equation (40), the three-axis angular velocity of star tracker can be calculated as follows: where = denotes the attitude quaternion and denotes the rotational angular velocity of the star tracker, respectively. Due to the short sampling time for calculations, the three-axis rotation angle of the star tracker can be calculated by using Equation (41): where ( ) denotes the quaternion at time k and ( ) denotes the three-axis rotation angle of the star tracker between time k and time k − 1. Since the star tracker does not rotate on the tripod, the three-axis rotation angle should be zero, theoretically. However, the measured three-axis rotation angle is not zero. The triple standard deviation (3σ) method is adopted to evaluate the accuracy of the star tracker. It should be explained that because the calculated rotation angle is positive, its probability density function is different from that of Gaussian distribution [30]. The result must be divided by the √2. The predicted accuracy (3σ) of star trackers can be expressed by the noise equivalent angle (NEA). The calculation equations of NEA are described as Equation (42) [31]. The roll axis error angle of the star tracker will be affected by the focal length. Therefore, the

Accuracy and Dynamic Performance
As shown in Figure 16a, in order to acquire the accuracy of star trackers at different sun incident angles, the 1000 quaternion data are calculated by the star tracker in real time at each sun incident angle. Due to the weather, only 32 • to 60 • experimental data are adopted. According to the quaternion differential equation as described in Equation (40), the three-axis angular velocity of star tracker can be calculated as follows: where Q = q 0 q 1 q 2 q 3 T denotes the attitude quaternion and ω b Rb denotes the rotational angular velocity of the star tracker, respectively. Due to the short sampling time for calculations, the three-axis rotation angle of the star tracker can be calculated by using Equation (41): where Q (k) denotes the quaternion at time k and θ (k) denotes the three-axis rotation angle of the star tracker between time k and time k − 1. Since the star tracker does not rotate on the tripod, the three-axis rotation angle should be zero, theoretically. However, the measured three-axis rotation angle is not zero. The triple standard deviation (3σ) method is adopted to evaluate the accuracy of the star tracker. It should be explained that because the calculated rotation angle is positive, its probability density function is different from that of Gaussian distribution [30]. The result must be divided by the √ 2. The predicted accuracy (3σ) of star trackers can be expressed by the noise equivalent angle (NEA). The calculation equations of NEA are described as Equation (42) [31]. The roll axis error angle of the star tracker will be affected by the focal length. Therefore, the NEA of roll axis will be worse than that of cross-boresight. The equation is described as follows: where N e_pixel denotes the number of effective pixels, E centroid denotes the average centering accuracy and N star denotes the average number of recognized stars. The design parameters and predicted accuracy of the DST are shown in Table 5. The practical accuracy (3σ) variation between the proposed DST and TST with the same lens and detector under different sun incident angles is shown in Figure 17. The three-axis average accuracy (3σ) is shown in Table 6.
parameters and predicted accuracy of the DST are shown in Table 5.  (3 ) The practical accuracy (3σ) variation between the proposed DST and TST with the same lens and detector under different sun incident angles is shown in Figure 17. The three-axis average accuracy (3σ) is shown in Table 6.  The average accuracy of the DST is better than 2″ (3σ). However, in the whole experiment, the accuracy of the DST is better than 3″ (3σ). Due to the influence of weather and the installation in the experiment, the accuracy of the two star trackers is somewhat Figure 17. The variation of three-axis accuracy for two star trackers. The average accuracy of the DST is better than 2" (3σ). However, in the whole experiment, the accuracy of the DST is better than 3" (3σ). Due to the influence of weather and the installation in the experiment, the accuracy of the two star trackers is somewhat different. However, it is within the allowable error range. When the sun incident angle is close to the designed sunlight suppression angle, the accuracy of DST and TST becomes simultaneously worse. Although the energy of the stars is greater than the stray light, the gray values of the stars becomes higher. The centroid method for extracting the stars would result in the offset of the star coordinates. This problem can be solved if a more advanced star extraction algorithm is adopted.
It should be explained that the accuracy of the DST is the measurement accuracy of the instrument at that time and environment. If the absolute attitude data of the star tracker needs to be obtained, some important factors such as chromatic aberration, temperature, stellar aberrations and proper motion should be further considered [32]. The lens of the DST has completed the correction of distortion and chromatic aberration. Bulk thermal changes can be corrected by on-orbit recalibration. Stellar aberrations and proper motion can be corrected by an accurate real-time clock and orbital ephemeris.
The remote sensing CubeSats usually do not regard the dynamic performance as important and so the designed parameters about the lens and detector are mainly focused on accuracy. The DST and TST are fixed on a uniaxial turntable without stray light and the turntable rotates at a constant slew rate within ±10 • , as shown Figure 18. The rotation angular velocity of the star tracker can be calculated by Equation (40). The slew rate is constant and so the angular calculated by Equation (41) increased and decreased uniformly. The triple standard deviation (3σ) of the angular is adopted to evaluate the accuracy.
would result in the offset of the star coordinates. This problem can be solved if a more advanced star extraction algorithm is adopted. It should be explained that the accuracy of the DST is the measurement accuracy of the instrument at that time and environment. If the absolute attitude data of the star tracker needs to be obtained, some important factors such as chromatic aberration, temperature, stellar aberrations and proper motion should be further considered [32]. The lens of the DST has completed the correction of distortion and chromatic aberration. Bulk thermal changes can be corrected by on-orbit recalibration. Stellar aberrations and proper motion can be corrected by an accurate real-time clock and orbital ephemeris.
The remote sensing CubeSats usually do not regard the dynamic performance as important and so the designed parameters about the lens and detector are mainly focused on accuracy. The DST and TST are fixed on a uniaxial turntable without stray light and the turntable rotates at a constant slew rate within 10°, as shown Figure 18. The rotation angular velocity of the star tracker can be calculated by Equation (40). The slew rate is constant and so the angular calculated by Equation (41) increased and decreased uniformly. The triple standard deviation (3σ) of the angular is adopted to evaluate the accuracy. The uniaxial turntable is rotated at 0.5, 1.0, 1.5, 2.0, 2.5 and 3.0°/s in dynamic performance experiments. The calculated slew rate by two star trackers is shown in Figure 19. The average accuracy (3σ) under different slew rates is shown in Table 7. The uniaxial turntable is rotated at 0.5, 1.0, 1.5, 2.0, 2.5 and 3.0 • /s in dynamic performance experiments. The calculated slew rate by two star trackers is shown in Figure 19. The average accuracy (3σ) under different slew rates is shown in Table 7. The dynamic performance experiments show that the DST and the TST with same lens and detector are similar. The DST and the TST can both identify the stars under the maximum slew rate of 3 • /s. The reason why the accuracy of the star trackers decreases with the increase in slew rate is that the star spots are trailing as shown in Figure 3, which results in the offset of star spots centroid.  The dynamic performance experiments show that the DST and the TST with same lens and detector are similar. The DST and the TST can both identify the stars under the maximum slew rate of 3°/s. The reason why the accuracy of the star trackers decreases with the increase in slew rate is that the star spots are trailing as shown in Figure 3, which results in the offset of star spots centroid.

Discussion
In this paper, an on-orbit DST is proposed. The DST with high accuracy and small volume is realized by the deployable baffle and surrounding circuit structure. On the one hand, any large and high-accuracy star tracker such as ASTRO-15 can use the proposed model to reduce its volume. On the other hand, the designers can only focus on the volume of the lens and detector to make star trackers smaller and more accurate.

Discussion
In this paper, an on-orbit DST is proposed. The DST with high accuracy and small volume is realized by the deployable baffle and surrounding circuit structure. On the one hand, any large and high-accuracy star tracker such as ASTRO-15 can use the proposed model to reduce its volume. On the other hand, the designers can only focus on the volume of the lens and detector to make star trackers smaller and more accurate.
If there is difficulty in deploying the DST due to extreme space temperature, the satellite could send the deployment command for a longer period of time to allow the heating resistors to fuse the nylon wire. The satellite could also rely on other attitude sensors, such as sun sensors, when the DST could not be deployed. If the space temperature is appropriate, the satellite could send deployment commands. Actually, a satellite is usually equipped with more than two star trackers. If one of them could not be deployed, the others could be deployed successfully. If all the DSTs are not deployed for some reason, it does not mean that the DSTs cannot work. The result of this impact is that the ability of the baffle to suppress stray light will be weakened. The satellite requires readjustment to their attitude to ensure that stray light does not enter the FOV of the DST.
The DST can be used in IADCS designed for CubeSats. Compared with the IADCS400 [33] designed by Hyperion Technologies, the example IADCS can equip two DSTs as shown in Figure 20 such that the occupation of TST is greatly reduced. Moreover, the attitude determination accuracy with 3" (3σ) of the example IADCS is much higher than IADCS400 with 30" (3σ). Additionally, the DST can further reduce the rocket launch volume occupied by the star tracker. After the CubeSat enters the orbit, it can be deployed to release the space. The CubeSat would be subjected to certain spring forces during deployment, which can cause the satellite to rotate or deviate from its orbit. However, the IADCS can drive the reaction wheels or the propellers to solve that problem at this moment. ment, which can cause the satellite to rotate or deviate from its orbit. However, the IADCS can drive the reaction wheels or the propellers to solve that problem at this moment.
With future optimizations, the volume of DST can be further reduced to the volume limit. Thus, the high-accuracy satellite could be much smaller to reduce the launch volume and cost significantly. More and more organizations and companies would launch Cu-beSats to build their own constellation for scientific research or commercial viability. Figure 20. An example IADCS with two DSTs. The IADCS also includes a sun sensor, a gyroscope, three reaction wheels and three magnetorquers. In addition, the performance, interface and volume are listed.

Conclusions
By analyzing the relationship between volume and accuracy or dynamic performance, this paper proposed an on-orbit DST. The deployable baffles with a scientifically analyzed and verified taper and surrounding circuit structure are designed to minimize the volume of the star tracker. The experiment results show that the practical DST has a volume ratio close to the theoretical value. The simulations and experiments show that it can be deployed with an error close to zero and without self-locking risk due to the taper Figure 20. An example IADCS with two DSTs. The IADCS also includes a sun sensor, a gyroscope, three reaction wheels and three magnetorquers. In addition, the performance, interface and volume are listed.
With future optimizations, the volume of DST can be further reduced to the volume limit. Thus, the high-accuracy satellite could be much smaller to reduce the launch volume and cost significantly. More and more organizations and companies would launch CubeSats to build their own constellation for scientific research or commercial viability.

Conclusions
By analyzing the relationship between volume and accuracy or dynamic performance, this paper proposed an on-orbit DST. The deployable baffles with a scientifically analyzed and verified taper and surrounding circuit structure are designed to minimize the volume of the star tracker. The experiment results show that the practical DST has a volume ratio close to the theoretical value. The simulations and experiments show that it can be deployed with an error close to zero and without self-locking risk due to the taper and a series of strategies. Furthermore, the DST can even be deployed in extreme temperatures so that the DST would not be affected by the temperatures common to space environments. Compared to the TST with same lens and detector, the stray light suppression ability, accuracy (better than 3" (3σ)) and dynamic performance (up to 3 • /s) are nearly equal. More than one DST can easily be integrated in IADCS for CubeSats to provide high-accuracy attitude data for remote sensing applications.
Author Contributions: Conceptualization, X.L., F.X. and Z.Y.; investigation, X.L., F.X. and S.F.; participated in the modeling, X.L. and S.F.; collected the data and analyzed the experimental data, X.L.; collected the related resources and supervised the experiment, X.L. and F.X.; writing-original draft, X.L.; writing-review and editing, F.X.; project administration and funding acquisition, F.X. and Z.Y. All authors have read and agreed to the published version of the manuscript.