The Hidden Cairns—A Case Study of Drone-Based ALS as an Archaeological Site Survey Method

: Conducting archaeological site surveys is time consuming, and large sites may have many small features or structures that are difﬁcult to locate and interpret. Vegetation cover and dense forest hide small structures, like cairns, while at the same time forest cover can cause problems for LiDAR tools. In this case study, drone-based ALS (airborne laser scanning) was tested as an archaeological site survey tool. The research site was complex and located partially in a forested area, which made it possible to evaluate how forest cover affects data. The survey methods used were rather simple: visual analysis, point density calculations in the forest area, and, for site interpretation purposes, digitizing observations and viewshed analysis. Using straightforward methods allowed us to evaluate the minimum time and skills needed for this type of survey. Drone-based ALS provided good results and increased knowledge of the site and its structures. Estimates of the number of cairns interpreted as graves more than doubled as a result of the high-accuracy ALS data. Based on the results of this study, drone-based ALS could be a suitable high-accuracy survey method for large archaeological sites. However, forest cover affects the accuracy, and more research is needed. The commercial company Geotrim Oy conducted laser scanning at Nuuttilanmäki on 30 October 2019. A late-autumn day was chosen so that the leaf cover and vegetation level would be minimized. Weather conditions were good; but, unfortunately, the night before the temperature dropped below 0 ◦ C. At the time of the survey, there was still frost cover everywhere, which affected the orthophoto quality of the scans. The survey was done with a GeoDrone X4L multicopter and YellowScan Surveyor LiDAR sensor (Figure 5): detailed product speciﬁcations can be found at Geotrim’s website [28]. The YellowScan Surveyor was chosen because of its high accuracy that made it suitable for this type of research. The YellowScan surveyor can produce point cloud data at even 100 points per square metre with an absolute accuracy of 5 cm. The ﬁrst ALS ﬂight was done at a ﬂight altitude of 50 m and the second ALS ﬂight was done at a ﬂying altitude of 70 m. The gap between the ﬂight lanes was 50 m. The third ﬂight was done with a camera (Model: Sony RX1 RII): more information and product speciﬁcs can be found at, for example, Geotrim’s website [29]. The size of the study area was approximately 23 ha, and each ﬂying tour took about 25 min. The ﬂight plan and settings for the ﬂight were done just before the start.


Introduction
Based on several earlier studies, LiDAR has become an important tool for many archaeologists, especially when combined with archaeological surveys. Risbøl et al. summarized its technological developments and adaptations in the Fenno-Scandinavian area during the last 15 years [1]. They concluded that drone-based airborne laser scanning (ALS) will expand the field of research in the future. In Finland, research concerning the use of ALS in archaeology has been conducted in the last decade [2][3][4], and it has become an important tool for many archaeologists and authorities working with cultural heritage management sites. The National Land Survey of Finland (NLS) performed laser scanning in Finland in 2008-2019, and the point density of their data was, at minimum, 0.5 points per square metre [5]. Their laser scanning data sets, as well as digital elevation model (DEM) data sets derived from the ALS data, are openly available on the NLS website [6]. Viewing DEM data sets processed using the hillshade tool has been made very easy because such data sets are, for example, available at the Paikkatietoikkuna (national geoportal presenting spatial data and related services' website) [7]. In 2020, NLS started collecting new data sets with a density of 5 points per square metre, but those data sets will only be available with a user license [8]. New data sets with higher point densities will improve accuracy from the archaeological point of view. The University of Oulu started a new project called 'Automatic detection of archaeological sites in airborne laser scanning data, LIDARK' at the beginning of February 2021 [9]. The first archaeological survey results with the new improved NLS data sets were introduced in February 2021 at a Finnish Heritage Agency

Materials
The research site for the case study was Nuuttilanmäki 1-4 (called just Nuuttilanmäki in this paper). It is located in Hartola, in the Itä-Häme region of southern Finland (Figure 1). It was first discovered in 1997 by archaeologist Timo Sepänmaa [22]. In the first survey, four different areas were discovered: area 1 contains cairns, area 2 is a settlement site, area 3 has a cup-marked stone, and area 4 a cup-marked rock. At the time of discovery, archaeologists interpreted the site as a possible Stone Age settlement area since it contained some quartz flakes and other objects. Additionally, some Iron Age pottery was discovered, so the dating of the possible settlement area is uncertain. The next surveys at the site were done in 2003 by Hannu Poutiainen [23] and in 2004 by Timo Jussila and Hannu Poutiainen [24]. They estimated that the site contained 30-40 cairns with a diameter of between 3 and 10 m and a height of 20-100 cm. Burnt clay, iron slag, cremated bones, and an iron knife were found in the settlement area in the 2003 survey. In 2012, the Lahti City Museum conducted archival research on the historical sites in the region and pinpointed a possible new historical settlement site, Kalho, in the same area as Nuuttilanmäki [25]. The village of Kalho was first mentioned in the year 1405, and records show that in the year 1560 it contained 10 houses [26].

Materials
The research site for the case study was Nuuttilanmäki 1-4 (called just Nuuttilanmäki in this paper). It is located in Hartola, in the Itä-Häme region of southern Finland ( Figure  1). It was first discovered in 1997 by archaeologist Timo Sepänmaa [22]. In the first survey, four different areas were discovered: area 1 contains cairns, area 2 is a settlement site, area 3 has a cup-marked stone, and area 4 a cup-marked rock. At the time of discovery, archaeologists interpreted the site as a possible Stone Age settlement area since it contained some quartz flakes and other objects. Additionally, some Iron Age pottery was discovered, so the dating of the possible settlement area is uncertain. The next surveys at the site were done in 2003 by Hannu Poutiainen [23] and in 2004 by Timo Jussila and Hannu Poutiainen [24]. They estimated that the site contained 30-40 cairns with a diameter of between 3 and 10 metres and a height of 20-100 cm. Burnt clay, iron slag, cremated bones, and an iron knife were found in the settlement area in the 2003 survey. In 2012, the Lahti City Museum conducted archival research on the historical sites in the region and pinpointed a possible new historical settlement site, Kalho, in the same area as Nuuttilanmäki [25]. The village of Kalho was first mentioned in the year 1405, and records show that in the year 1560 it contained 10 houses [26]. A new archaeological site survey was conducted at the Nuuttilanmäki and Kalho sites and the areas near them in spring 2019. The survey aimed to establish whether the site might be suitable for the purposes of this case study and for drone-based ALS in A new archaeological site survey was conducted at the Nuuttilanmäki and Kalho sites and the areas near them in spring 2019. The survey aimed to establish whether the site might be suitable for the purposes of this case study and for drone-based ALS in general. The survey resulted in the conclusion that Nuuttilanmäki is a much larger and Remote Sens. 2021, 13, 2010 4 of 18 more complex archaeological site than previously known. More cairns were discovered in a forested area south of the field. In addition, Iron Age pottery and cremated bone pieces were discovered on the northern side of the river. Furthermore, a possible medieval village area was discovered. One new archaeological site (Peltola) was discovered closer to the lake. The site includes a cup-marked stone, cairns, and a settlement dating back to the historical period. The survey report included new interpretations of the site: The site includes a possible Iron Age settlement area and the cairns in the forested area seem to be different than those in the field areas. The cairns in the southern part of the forested area could be related to slash and burn agriculture, and they differ from the cairns in the field by size, shape, and structure (Figures 2 and 3). The survey concluded that the Nuuttilanmäki site needs more research and that precise interpretations are difficult when just conducting visual inspections. As part of the 2019 field study, the exact coordinates of the 32 structures interpreted as cairns were measured with a GNSS surveyor (model Trimble R10) for the reference purpose of this study. The GNSS system could not be used in the forested area because of the density of the forest cover; thus, only a few cairn locations were measured inside the forest with a mobile phone GPS so that the protected area could be digitized. The survey report [27] can be found at the Finnish Heritage Agency's website (Muinaisjäännösrekisteri). The results of the field survey and cairn locations are illustrated in Figure 4. Nuuttilanmäki was chosen for this case study because of its complexity and location. Cairns at the site are located partially in an open field and partially in two different forest types (a very dense, mature, spruce forest and a young, pine forest with some spruces covered with dense undergrowth), which are difficult types to study from an archaeological and ALS point of view.
could be related to slash and burn agriculture, an by size, shape, and structure (Figures 2 and 3) tilanmäki site needs more research and that prec conducting visual inspections. As part of the 2019 32 structures interpreted as cairns were measure R10) for the reference purpose of this study. The forested area because of the density of the fores were measured inside the forest with a mobile ph be digitized. The survey report [27] can be found (Muinaisjäännösrekisteri). The results of the fie trated in Figure 4. Nuuttilanmäki was chosen for and location. Cairns at the site are located partia different forest types (a very dense, mature, spr some spruces covered with dense undergrowth) an archaeological and ALS point of view.      The commercial company Geotrim Oy conducted laser scanning at Nu on 30 October 2019. A late-autumn day was chosen so that the leaf cover an level would be minimized. Weather conditions were good; but, unfortunate The commercial company Geotrim Oy conducted laser scanning at Nuuttilanmäki on 30 October 2019. A late-autumn day was chosen so that the leaf cover and vegetation level would be minimized. Weather conditions were good; but, unfortunately, the night before the temperature dropped below 0 • C. At the time of the survey, there was still frost cover everywhere, which affected the orthophoto quality of the scans. The survey was done with a GeoDrone X4L multicopter and YellowScan Surveyor LiDAR sensor ( Figure 5): detailed product specifications can be found at Geotrim's website [28]. The YellowScan Surveyor was chosen because of its high accuracy that made it suitable for this type of research. The YellowScan surveyor can produce point cloud data at even 100 points per square metre with an absolute accuracy of 5 cm. The first ALS flight was done at a flight altitude of 50 m and the second ALS flight was done at a flying altitude of 70 m. The gap between the flight lanes was 50 m. The third flight was done with a camera (Model: Sony RX1 RII): more information and product specifics can be found at, for example, Geotrim's website [29]. The size of the study area was approximately 23 ha, and each flying tour took about 25 min. The flight plan and settings for the flight were done just before the start. The commercial company Geotrim Oy conducted laser scanning at Nu on 30 October 2019. A late-autumn day was chosen so that the leaf cover and level would be minimized. Weather conditions were good; but, unfortunatel before the temperature dropped below 0 °C. At the time of the survey, there w cover everywhere, which affected the orthophoto quality of the scans. The done with a GeoDrone X4L multicopter and YellowScan Surveyor LiDAR sen 5): detailed product specifications can be found at Geotrim's website [28]. The Surveyor was chosen because of its high accuracy that made it suitable for research. The YellowScan surveyor can produce point cloud data at even 100 square metre with an absolute accuracy of 5 cm. The first ALS flight was don altitude of 50 m and the second ALS flight was done at a flying altitude of 70 between the flight lanes was 50 m. The third flight was done with a camera (M RX1 RII): more information and product specifics can be found at, for example website [29]. The size of the study area was approximately 23 ha, and each flyin about 25 min. The flight plan and settings for the flight were done just before  After the field study, a Geotrim Oy engineer preprocessed the ALS data and produced the orthophoto from the images. Preprocessing the data was also fast, and readymade LAZ files were delivered and ready to use after three working days. Basic data processing and map production was done using the ArcMap 10.  Table 1.

Methods
Visual data inspection was chosen as the high-accuracy site survey method. The study area (one archaeological site) was limited, so visual inspection and digitising the features with ArcMap program did not take much time. By keeping the data processing as simple as possible, we also evaluated the minimum time and effort needed for this process. After using the ArcMap program for point cloud comparison, ground points were then transformed into DEMs using a LAS data set to raster conversion tool. Data set one was converted to a 0.2 × 0.2 m DEM and then to a 0.1 × 0.1 m DEM with the same basic settings. There were only minor visual differences between the two raster data sets. Then, the same process was repeated for data set two. Using visual comparison, the 0.1 × 0.1 raster made from data set one was chosen for further data processing. Comparing the various data visualisation methods was beyond the scope of this study. LiDAR data visualisation methods for archaeology use have been discussed and compared in many papers previously [30]. The basic ArcMap hillshade tool yielded quite good results, but the best visual result was achieved with the Relief Visualization Toolbox 2.2.1 program [31] and with a tool measuring hillshade from multiple directions (number of directions 16 and sun elevation angle 35), which was then used in the ArcMap program.
Point density calculations were chosen as a simple method for evaluating forest and vegetation effect. Archaeological features like small structures are usually at ground level or very close to ground level; if the point density from the ground is very low, then the results can be unreliable from an archaeological standpoint. To assess the impact of different forests and vegetation on the point density, three different vegetation areas were identified from the orthophoto ( Figure 6). The southern area (stand 1) was a very dense, mature, spruce forest and classified as forest with grass-herb vegetation type. The middle area (stand 2) was a young, pine forest with some spruces in the middle belonging to the grass-herb vegetation forest type. Information about forest resources and types were collected from the Karttaselain web page [32]. The northern area between the road and the forest (stand 3) was open grassland that had been used as pasture area, and it was defined as a threatened, seminatural grasslands and grazed woodlands habitat type. All three areas were digitized as polygons. Point densities were determined using the LAStools toolbox (rapidlasso GmbH, Gilching, Germany). First, laser points representing the ground were extracted from the point cloud using the lasground tool of the LAStools toolbox. The tool detects ground points using a slightly tuned version of Axelsson [33]. A digital terrain model (DTM) was then formed using the ground points. Next, the height above ground was calculated for each non-ground point by subtracting the corresponding DTM value from the height of the point. Points located within 1 metre of the ground were classified as low vegetation points. Point densities were calculated separately for the two forest stands and grassland areas, the two flying altitudes and two point classes, ground class and low vegetation class. Thus, 12 different point densities were acquired as a result. The point densities were calculated by simply determining the number of points within the stands and dividing the number of points by the area of the stand.
Visual data evaluation continued with site interpretations. Cairns that were spotted using the hillshade map and orthophotos were divided into two classes based on their shape, size, and appearance: as possible graves or cairns that are related to agriculture. Cairns that were interpreted as graves were digitized as polygons. Other interesting structures, such as pits in the old village area, were also digitized. The largest cairn proved interesting, and that location was chosen for testing visibility using the viewshed analyzing tool in ArcMap. The largest cairn differed from others due to its size and location, which gave the impression that it is meant to be very visible, unlike those other smaller cairns. During the field survey, the current vegetation made it difficult to evaluate how visible the largest cairn could be from the river or lake direction.Visibility analysis is a quite common GIS method in archaeology and it can yield interesting results; however, such results are often also subject to the interpretations made by various researchers [34]. DTM value from the height of the point. Points located within 1 metre of the grou classified as low vegetation points. Point densities were calculated separately fo forest stands and grassland areas, the two flying altitudes and two point classes class and low vegetation class. Thus, 12 different point densities were acquired a The point densities were calculated by simply determining the number of poin the stands and dividing the number of points by the area of the stand. Visual data evaluation continued with site interpretations. Cairns that wer using the hillshade map and orthophotos were divided into two classes based shape, size, and appearance: as possible graves or cairns that are related to ag Cairns that were interpreted as graves were digitized as polygons. Other interest tures, such as pits in the old village area, were also digitized. The largest cair interesting, and that location was chosen for testing visibility using the viewshe ing tool in ArcMap. The largest cairn differed from others due to its size and which gave the impression that it is meant to be very visible, unlike those othe cairns. During the field survey, the current vegetation made it difficult to evalu visible the largest cairn could be from the river or lake direction.Visibility ana quite common GIS method in archaeology and it can yield interesting results; such results are often also subject to the interpretations made by various researc

Results
The results for the high-accuracy survey were good. Together, LiDAR and orthophotos provided much new, detailed information about the Nuuttilanmäki site. Based on the visualisations (coloured DEM and multihillshade) and orthophotos, we identified a total of 150 possible cairns and digitized each of them into point format (Figures 7 and 8). Some of the cairns were more difficult to interpret than others. Especially cairns that could be related to agriculture in the possible old cultivation area were more difficult to spot, as they did not have such a clear form or shape as possible graves. We made the same observation about cairn types in the field. Possible graves include mounds carefully constructed with stones of the same size and consisting of low and symmetric structures, whereas cairns in the deep, forested area consisted of all sizes of stones that had been thrown into a single mound. Forest cover and dense vegetation clearly affected the ground point density, as was expected. Especially one area with dense, young spruce was problematic. The stand 2 area was also very difficult to access and interpret in the field survey because of dense undergrowth ( Figure 9). One of the most problematic areas with young spruces can be spotted already from the point clouds ( Figure 10), and those same spots proved problematic when using the hillshade tool. Point density calculations showed the significant effect of those spots on different forested areas (Figures 11 and 12). In the open field area, the point density from the ground was very good, with data set 1 having an average of 69.22 points per square metre and data set 2 an average of 52.15 points per square metre. In the forested areas, the ground point density dropped on average to 12-18 points per square metre. The first aim of this study was to evaluate drone-based ALS as an archaeological site survey tool. Drones are often used for photography purposes in archaeological research, but no earlier research has inspected the potential of drone-based ALS as a site survey method in Finland. Conducting archaeological field surveys is often quite time consuming and, thus, it can be quite expensive, especially if the area is large and contains many different features, like small structures. The Finnish Heritage Agency has published quality guidelines for archaeological fieldwork in Finland [11], and those guidelines state that the purpose of the survey is to create an overview of cultural heritage in the area and provide information on the number, location, types, and extent of archaeological sites in the survey area. They also divide survey methods into a general survey, theme survey, and 'highaccuracy survey'. A high-accuracy survey aims to define and extend the archaeological site or area as reliably as possible via mostly non-destructive techniques, such as geophysical or remote sensing methods. Only one previous study with drone-based ALS has been conducted in Finland, although the results have not yet been published [12]. However, the LiDAR data used in the present study have already been introduced in another article [1]. Drone-based ALS was tested, for example, in Norway in 2018 with promising results [13] and in Italy in 2021 [14]. However, more research is needed on drone-based ALS in archaeology.
The second aim of this study was to evaluate how different forest types and the density of vegetation affect the detection of archaeological sites. Some of the major challenges of using LiDAR in archaeology have been studied before, especially in forested areas. Especially one area with dense, young spruce was problematic. Th was also very difficult to access and interpret in the field survey because o growth (Figure 9). One of the most problematic areas with young spruces already from the point clouds (Figure 10), and those same spots proved prob using the hillshade tool. Point density calculations showed the significant spots on different forested areas (Figures 11 and 12). In the open field area, sity from the ground was very good, with data set 1 having an average of 69 square metre and data set 2 an average of 52.15 points per square metre. I areas, the ground point density dropped on average to 12-18 points per sq        We visually interpreted the sites based on the data and then confirmed th wards through a field survey. The number of cairns interpreted as graves more t bled: The original estimation was 30-40 graves, while the new estimation, base visualisations and orthophoto, was 89 graves. On the north side of the road, we and digitized 10 clear pits. On the eastern side of the pits, we discovered an in oval-shaped, low hillock or mound, which could be the foundation of a larger From the current road toward the hillock was a flattened area, which was also in and could be the traces of an earlier road or path ( Figure 13). A new, one-day fiel was conducted in May 2020 just to confirm the findings in the LiDAR data. The survey confirmed our interpretations of the cairn types and their locations. Com with the previously GNSS-measured cairn locations revealed some differences pretations ( Figure 14), but without full excavations it was impossible to confirm them. Making interpretations in the field was also difficult, so cairn locations m with GNSS may also contain mistakes. Orthophoto was also used to separate cairns from the stones in the open field area. There were some big stones that loo similar to cairns in the hillshade data. The grave cairns seemed to be located in and it was possible to calculate their area based on the polygons. Altogether, t covered an area of 1199 square metres, with the mean value being 13.5 square m the largest cairn alone covering approximately 45.5 square metres. The viewshed from the location of the largest cairn showed that it may have been visible from direction if the vegetation level had been low ( Figure 15). LiDAR data from t survey only covered a very limited area, so the viewshed analysis utilized a 2 × 2 made by the National Land Survey of Finland. The lake direction is important We visually interpreted the sites based on the data and then confirmed them afterwards through a field survey. The number of cairns interpreted as graves more than doubled: The original estimation was 30-40 graves, while the new estimation, based on the visualisations and orthophoto, was 89 graves. On the north side of the road, we spotted and digitized 10 clear pits. On the eastern side of the pits, we discovered an interesting oval-shaped, low hillock or mound, which could be the foundation of a larger building. From the current road toward the hillock was a flattened area, which was also interesting and could be the traces of an earlier road or path ( Figure 13). A new, one-day field survey was conducted in May 2020 just to confirm the findings in the LiDAR data. The new site survey confirmed our interpretations of the cairn types and their locations. Comparison with the previously GNSS-measured cairn locations revealed some differences in interpretations ( Figure 14), but without full excavations it was impossible to confirm any of them. Making interpretations in the field was also difficult, so cairn locations measured with GNSS may also contain mistakes. Orthophoto was also used to separate possible cairns from the stones in the open field area. There were some big stones that looked very similar to cairns in the hillshade data. The grave cairns seemed to be located in a cluster, and it was possible to calculate their area based on the polygons. Altogether, the cairns covered an area of 1199 square metres, with the mean value being 13.5 square metres and the largest cairn alone covering approximately 45.5 square metres. The viewshed analysis from the location of the largest cairn showed that it may have been visible from the lake direction if the vegetation level had been low ( Figure 15). LiDAR data from the drone survey only covered a very limited area, so the viewshed analysis utilized a 2 × 2 m DEM made by the National Land Survey of Finland. The lake direction is important because one significant west-to-east water route traversed the lake and one route to the village was via the lake and the smaller Kalho river.
Remote Sens. 2021, 13, x FOR PEER REVIEW 11 of 16 one significant west-to-east water route traversed the lake and one route to the village was via the lake and the smaller Kalho river.   Remote Sens. 2021, 13, x FOR PEER REVIEW 11 of 16 one significant west-to-east water route traversed the lake and one route to the village was via the lake and the smaller Kalho river.

Discussion
One important factor limiting the use of drone-based ALS in archaeology is price of the instruments and the skills required to use them and perform data pr In this case study, we accomplished the survey work by cooperating with a co company that conducted the ALS with a drone and preprocessed the data. It is to buy a professional survey service, like a drone-based ALS survey. In Finland chaeological surveys are done by commercial archaeology companies [35,36]. Fo son, it is also good to evaluate the survey process from that perspective. If the d utilize drone-based ALS as an archaeological site survey method, it must be fast ple to perform. Not all archaeologists are familiar with GIS, and so it may be d utilize such a method for commercial archaeology if it requires special skills or e tools. This research project was conducted as simply as possible, and the sam could be followed in commercial archaeology. If the study area is large and conta small details that need to be spotted and documented, drone-based ALS could b ble method for such cases. For smaller archaeological sites, the benefits of sav would be smaller and other methods like TLS or MLS should be also considered LiDAR data processing part of this study was fast. The process introduced in the sections takes only about 1-2 working days, depending on how familiar the res with the GIS programs. In the future, drone-based ALS data from the archaeolog could be also visualized in 3D and, for example, in virtual reality. With virtu places can be experienced from an egocentric and stereoscopic perspective [38]. person view could provide understanding about the archaeological site landsc

Discussion
One important factor limiting the use of drone-based ALS in archaeology is the high price of the instruments and the skills required to use them and perform data processing. In this case study, we accomplished the survey work by cooperating with a commercial company that conducted the ALS with a drone and preprocessed the data. It is possible to buy a professional survey service, like a drone-based ALS survey. In Finland, most archaeological surveys are done by commercial archaeology companies [35,36]. For this reason, it is also good to evaluate the survey process from that perspective. If the desire is to utilize drone-based ALS as an archaeological site survey method, it must be fast and simple to perform. Not all archaeologists are familiar with GIS, and so it may be difficult to utilize such a method for commercial archaeology if it requires special skills or expensive tools. This research project was conducted as simply as possible, and the same process could be followed in commercial archaeology. If the study area is large and contains many small details that need to be spotted and documented, drone-based ALS could be a suitable method for such cases. For smaller archaeological sites, the benefits of saving time would be smaller and other methods like TLS or MLS should be also considered [37]. The LiDAR data processing part of this study was fast. The process introduced in the previous sections takes only about 1-2 working days, depending on how familiar the researcher is with the GIS programs. In the future, drone-based ALS data from the archaeological sites could be also visualized in 3D and, for example, in virtual reality. With virtual reality, places can be experienced from an egocentric and stereoscopic perspective [38]. The first-person view could provide understanding about the archaeological site landscapes. Today Finnish Heritage Agency only accepts small-size PDF files as survey reports and the reports can be, for example, found via Kulttuuriympäristön palveluikkuna web page [39]. Digital archaeological data, like 3D models, are not collected, stored, or archived in Finland yet. Improving archaeological survey methods and producing high-accuracy data are not enough if the data are not archived for the future in any way. Solutions for digital archiving should be found soon [40]. Besides simple maps in a PDF report, other options to visualize archaeological spatial data could be considered as well.
As a non-destructive site survey method, drone-based ALS produced new, useful information about the research site and the research complemented previous knowledge about the Nuuttilanmäki site. One of the biggest advantages of this method is that it saves time. Fieldwork with the drone was done smoothly and quickly. In the field, the three separate flying rounds and several settings between them took only about two working hours. Surveying the same large and complex area with other methods, like using a total station or TLS, would have taken many days or even weeks to obtain the same high-accuracy survey data and coordinates for all the structures. Using drone-based ALS before the actual field survey in the future would help researchers focus on and identify those features or structures inside the larger area that need more visual inspection. Visual evaluation and interpretation of the data was fast, and digitising those observations was simple. Soon, other high-accuracy LiDAR data sets will be available for Finland [41]. Since this data set is actually the first such high-accuracy data set, in the future it could serve as reference material for many other corresponding research projects. The data are also suitable for more complex analyses that could yield even more detailed information about the site or its structures. In the future, when more data are available, automatic detection of the cairns or pits could provide a different point of view. Overall, the research area is challenging and the site is complex, so more research is needed for more reliable interpretations. Estimations of the number of possible graves more than doubled, but it is possible that plenty more cairns remain hidden in the ground. Previous studies have shown that Iron Age graves are difficult to locate precisely because structures can also be more underground [18].
Forest and dense vegetation affect the drone-based ALS results from an archaeological standpoint. This should be considered when using other LiDAR data sets in archaeological surveys. To evaluate data accuracy, orthophotos could provide useful information about the vegetation cover. The National Land Survey of Finland provides orthophotos for all of Finland in open access format, and the data sets can be downloaded together with the DEMs [42]. Detailed information about the forest types can be found via the karttaselain application. For cultural heritage protection, we need more information and monitoring especially of those sites that are in forested areas and possibly at risk of damage because of forestry operations [20]. First, we should evaluate just what sites are most critical or require more research. The role of remote sensing in that respect can be significant. Remote sensing data and especially high-accuracy data, like in the present case study, could also help researchers monitor the sites after such forestry operations as thinning, clearcutting, or afforestation. The Nuuttilanmäki research site is partly located in the forest, and research could continue in the future after forestry operations with a new, high-accuracy survey, thereby making it possible to evaluate the effects of such operations. However, to best protect the archaeological sites from forestry operations we need to first know what kind of information is required from the forest management perspective. For example, how accurate should knowledge be about the structures at the site in order to protect them? The Finnish Heritage Agency has published some guidelines about forestry and cultural heritage [43]. Forestry operations are allowed in archaeological sites but damaging or covering the site is prohibited. For instance, driving over the site structures, like cairns, is prohibited. Furthermore, protected areas should be marked on the field beforehand. Detailed information about the locations of the archaeological site structures is not always easy to find or access, though. Harvester drivers or loggers particularly could benefit from high-accuracy archaeological data in their work plan and maps. In the future, cooperation between archaeologists and forestry professionals could benefit both sectors. One study about that type of cooperation was done between 2011 and 2013 with good results [44].
From a site interpretation perspective, high-accuracy data expanded previous knowledge on the hidden cairns at Nuuttilanmäki. Large areas like in this study are difficult to observe and outline. Mapping all the structures helps us understand the complexity of the site. In this case study, one problem encountered when making interpretations was a lack of reference material or suitable reference sites. As said before, no high-accuracy remote sensing data sets exist from sites that could be suitable for comparison. Current open access DEM data sets are not accurate enough, and these types of Iron Age cemetery sites are not visible enough in the data. Overall, archaeological research has been quite limited and minimal in this part of Finland. One site, Kotisalo, which is located in the same municipality, about 14 km to the northeast, could be a similar Iron Age cemetery with cup-marked stones and a possible settlement site. One of the cairns at the Kotisalo site was excavated in 2003, with the cairn type proving quite mysterious and not allowing for any clear conclusions after the excavations [45]. It could be interesting to compare cairns at different possible Iron Age cemeteries based on their spatiality, sizes, shapes, and other features in the future. This high-accuracy survey supported the hypothesis that some of the cairns are Iron Age graves. Those cairns appear in a cluster form and cover such a large area that no space is available for cultivation in that part of the research site. In that area, the soil is very rocky and not suitable for basic agriculture. During the field survey, a metal detector was used in a non-destructive manner, and it gave off metal signals for those possible graves. It is also possible that those cairns are not graves at all and the purpose is not yet known; without excavations, it is difficult to confirm their purpose. Pits in the village area were easy to spot during the survey, but the oval-shaped mound was not so visible when the field survey was done. The largest cairn was perhaps built to be seen, as the top of it is one big stone that can be seen from a distance. The location of that cairn, on the edge of the slope, is optimal if it is meant to be visible and not hidden. If the site area had been free of vegetation or forest cover, then the village could have been spotted from the lake and the water route.

Conclusions
Drone-based ALS provided much detailed information about a difficult, complex, and large-scale archaeological site. Compared to previous field studies done at the site, knowledge about the structures and site type increased a great deal after just a minimum amount of time and effort using this method. Drone-based ALS was also a fast way to collect very precise survey data. Collecting the same data with other methods, such as total station or TLS, would take much longer at a research site like the one assessed in this case study. Drone-based ALS is a useful method for conducting an archaeological site survey if the research site is large and contains many small structures, like in this case study. However, vegetation and its effect on the data quality from an archaeological standpoint should be considered in future research. As shown in this study, a very dense forest can diminish data quality. From a cultural heritage and management point of view, drone-based ALS could provide quite useful information and support archaeological interpretations.  Data Availability Statement: Third-party data restrictions apply to the availability of the data. Data were obtained from Geotrim Oy and are available from the author [Johanna Roiha] with the permission of Geotrim Oy. The results will be reported to the Finnish Heritage Agency following their guidelines.