Reclaimed Area Land Cover Mapping Using Sentinel-2 Imagery and LiDAR Point Clouds

: This paper investigates the possibility of using fusion Sentinel-2 imageries (2016, ESA) and light detection and ranging (LiDAR) point clouds for the automation of land cover mapping with a primary focus on detecting and monitoring a ﬀ orested areas and deriving precise information about the spatial (2D and 3D) characteristics of vegetation for reclaimed areas. The study was carried out for reclaimed areas – two former sulfur mines located in Southeast Poland, namely, Jezi ó rko, where 216.5 ha of a ﬀ orested area was reclaimed after borehole exploitation, and Mach ó w, where 871.7 ha of dump area was reclaimed after open cast strip mining. The current land use and land cover (LULC) classes at the Mach ó w and Jezi ó rko former sulfur mines are derived based on Sentinel-2 image processing, and conﬁrmed the applied type of reclamation for both analysed areas. The following LULC classes showed a signiﬁcant spatial range: broad-leaved forest, coniferous forest, and transitional woodland shrub. The progress of a ﬀ orested areas, not only in terms of the occupied area, but also in terms of the growth of trees and shrubs, was conﬁrmed. The results of the study showed di ﬀ erences in vegetation parameters, namely, height and canopy cover. Various stages of vegetation growth were also observed. This indicates an ongoing process of vegetation development, as an e ﬀ ect of the reclamation treatment for these areas.


Introduction
Space management and monitoring environmental changes are nowadays very important issues. Monitoring the land use and land cover (LULC) changes, including the development of forest phytocoenoses, is one of the elements allowing us to observe the changes taking place in the environment, where it seems reasonable to indicate the possibility of automation and the application of the newest technologies and geodata. LULC changes are also essential in regards to the programs of the European Union, including the subject of proper land management and granting direct subsidies to agriculture. Farmers are obliged to maintain their farmland for so-called "good agriculture", that is, they have to prevent soil erosion and the succession of vegetation as they are not useful for agricultural production [1,2]. This issue is also vital for the assessment of the biomass, renewable energy, and problems of coal sequestration [3].
In modern and sustainable forestry, environmental management, conservation of nature or natural resources, and landscape protection, remote sensing technologies are more and more commonly applied [4][5][6]. The process of land cover mapping, especially in terms of reclaimed areas, is the subject Sentinel-2 satellite imageries (European Space Agency; ESA) consist of two satellites: Sentinel-2A (launched in 2015) and Sentinel-2B (launched in 2017). The satellites are equipped with modern multi-spectral high-resolution scanners-13 spectral channels with spatial resolution of 10, 20, and 60 m. Using Sentinel-2 (ESA) imageries opens up new possibilities in environmental studies [11,[31][32][33][34], mainly as a result of the good spatial and spectral resolution and short revisit time (five days for two satellites).
LiDAR (light detection and ranging) remote sensing technology offers possibilities for collecting 3D information (point clouds), and allows for the definition of many indices; characterizing vegetation; and provides possibilities for monitoring land cover, together with the identification of the spatial parameters of the vegetation [35][36][37][38][39].
In the case of forested areas, advanced analyses of the vegetation structure are performed, based on the canopy height model (CHM), which is the same as the normalized digital surface model (nDSM, [40]) generated from classes (i.e., ground and vegetation). LiDAR point clouds are employed for collecting 2D and 3D information about vegetation, as they are useful for obtaining precise information about the height of the vegetation and canopy cover. Directly, airborne laser scanning (ALS) point clouds can also be retrieved for other vegetation parameters, such as the light penetration index, the number of trees, the number and area of gaps, the crown size, or the vertical structure of the forest stand (i.e., features that are strongly correlated with the biomass of the vegetation) [41][42][43][44][45][46][47][48].
The general objective of this paper was to define the possibilities of automation in LULC mapping for two former and reclaimed sulfur mine areas, especially the identification of afforested areas and forest succession dynamics, using Sentinel-2 imageries and LiDAR technology. The aim of the study was to identify the potential, for example, increases in vegetation height and canopy cover, using this geodata to highlight the progress of the occupied forested areas for reclaimed areas, as well as the growth of the trees and shrubs.

Data and Methods
The study areas were the former sulfur mines of Jeziórko (50 •  Sentinel-2 satellite imageries (European Space Agency; ESA) consist of two satellites: Sentinel-2A (launched in 2015) and Sentinel-2B (launched in 2017). The satellites are equipped with modern multi-spectral high-resolution scanners − 13 spectral channels with spatial resolution of 10, 20, and 60 m. Using Sentinel-2 (ESA) imageries opens up new possibilities in environmental studies [11,[31][32][33][34], mainly as a result of the good spatial and spectral resolution and short revisit time (five days for two satellites).
LiDAR (light detection and ranging) remote sensing technology offers possibilities for collecting 3D information (point clouds), and allows for the definition of many indices; characterizing vegetation; and provides possibilities for monitoring land cover, together with the identification of the spatial parameters of the vegetation [35][36][37][38][39].
In the case of forested areas, advanced analyses of the vegetation structure are performed, based on the canopy height model (CHM), which is the same as the normalized digital surface model (nDSM, [40]) generated from classes (i.e., ground and vegetation). LiDAR point clouds are employed for collecting 2D and 3D information about vegetation, as they are useful for obtaining precise information about the height of the vegetation and canopy cover. Directly, airborne laser scanning (ALS) point clouds can also be retrieved for other vegetation parameters, such as the light penetration index, the number of trees, the number and area of gaps, the crown size, or the vertical structure of the forest stand (i.e., features that are strongly correlated with the biomass of the vegetation) [41][42][43][44][45][46][47][48].
The general objective of this paper was to define the possibilities of automation in LULC mapping for two former and reclaimed sulfur mine areas, especially the identification of afforested areas and forest succession dynamics, using Sentinel-2 imageries and LiDAR technology. The aim of the study was to identify the potential, for example, increases in vegetation height and canopy cover, using this geodata to highlight the progress of the occupied forested areas for reclaimed areas, as well as the growth of the trees and shrubs.

Data and Methods
The study areas were the former sulfur mines of Jeziórko (50 0  The post-mining sites and sulfurous soils are a unique example of anthropogenically-created conditions that are extremely difficult for natural succession and adaptation in conditions of severe environmental stress, which, at a time of environmental and climate change, [49,50] is important for the global situation and cognition in this field. The areas after sulfur mining are characterized by difficult conditions for reclamation and vegetation growth. In this case, especially for the Jeziórko The post-mining sites and sulfurous soils are a unique example of anthropogenically-created conditions that are extremely difficult for natural succession and adaptation in conditions of severe environmental stress, which, at a time of environmental and climate change, [49,50] is important for the global situation and cognition in this field. The areas after sulfur mining are characterized by difficult conditions for reclamation and vegetation growth. In this case, especially for the Jeziórko sulfur mine, where the area was strongly chemically transformed because of the method of exploitation (underground melting, borehole method, and Frasch method), it is a very difficult area for the adaptation of vegetation (Figure 2) [51][52][53][54].
Remote Sens. 2020, 12, 261 5 of 20 60 kg ha-1 K2O), and grass sowing [52]. The next step of reclamation was area afforestation, mainly with one-year-old Scots pine seedlings (Pinus sylvestris L.) and an admixture of silver birch (Betula pendula Roth) and boreal oak (Quercus rubra L.) [51]. Of the more than 2000 ha previously occupied by the mine, over 700 hectares in total were reforested, of which 216.5 hectares, where this research was conducted, are currently managed by the Nowa Dęba Forest Inspectorate, State Forest National Forest Holding. Currently, the object is reforested mainly by scot pine and birch that are about 30 years old.  The former Machów sulfur mine and former Jeziórko sulfur mine are located in Southern Poland, near Tarnobrzeg. The region has an average annual temperature of 8.2 • C (-1.6 • C in January, and +18.7 • C in July), and the average annual precipitation ranges from 550 to 650 mm. The growing season lasts from 200 to 220 days per annum.
Sulfur was exploited from 1969 to 1992, using an open pit method in the Machów sulfur mine. During the open pit method of exploitation, large-scale underground excavations were created (about 560 ha; 80-100 m in depth) as well as above-level external excavations. During the exploitation period, 280 mln m 3 of soil was moved and formed into a heap. The reclaimed heap area after sulfur mining occupied more than 880 ha. The reclamation process of Machów (from 1976 to 1998) included technical road building, landscaping, strengthening the slopes to minimize erosion, and plant cultivation on slopes and shelfs.
Sulfur mining in Jeziórko started in 1966, and the sulfur was exploited using a Frasch method (underground melting). The Jeziórko sulfur mine was the first and the biggest mine in Poland where sulfur was exploited using the Frasch method. Poland was the third-largest sulfur producer in the world using this method. The Frasch method was connected with a high geological and, in particular, chemical transformation of the land. The reclamation process (from 1993 to 2010) to forestry (about 216 ha) included removing the mine infrastructure (such as mine wells, pipelines, and access roads), improvements to hydrographic conditions and landscaping, pH neutralization of sulfurous and excessively acidic soils by liming (average 400-500 Mg ha-1 of sludge), fertilization (70 kg ha-1 P 2 O 5 , 60 kg ha-1 K 2 O), and grass sowing [52]. The next step of reclamation was area afforestation, mainly with one-year-old Scots pine seedlings (Pinus sylvestris L.) and an admixture of silver birch (Betula pendula Roth) and boreal oak (Quercus rubra L.) [51]. Of the more than 2000 ha previously occupied by the mine, over 700 hectares in total were reforested, of which 216.5 hectares, where this research was conducted, are currently managed by the Nowa Dęba Forest Inspectorate, State Forest National Forest Holding. Currently, the object is reforested mainly by scot pine and birch that are about 30 years old.
The study was prepared based on the following data sets: Preliminary processing of the Sentinel-2 image was carried out using the SNAP 3.0.0 (ESA opensource software). Atmospheric correction was applied (Geomatica, PCI Geomatics). The main step was the Sentinel-2 image classification using the pixel-based supervised method (minimum distance algorithm; ILWIS). The classification was carried out by a photointerpretation key for Sentinel-2: RGB (red, green, and blue) and CIR (red, green, and NIR) composition, prepared during the field study (the training areas; area of interest; AOI) using a Spectra Precision GNSS receiver. The number of AOI was around 600 pixels for Machów and 350 for Jeziórko. The assessment of the classification results was carried out (ILWIS) by the Confusion Matrix function, which defined the average accuracy (AA), average reliability (AR), and overall accuracy (OA) based on the validation points. The validation points were chosen for each class from the test areas-not including the training areas. The number of validation points was around 2300 pixels for Machów and 600 for Jeziórko. The image classification result was generalized with the Boundary Clean and Majority Filter function (ArcGIS, Esri).
Airborne laser scanning point clouds were used to obtain precise information about the structure (2D and 3D) of the terrain and vegetation [41][42][43][44][45][46][47][48]. The processing of ALS point clouds was started by the following generated models: digital terrain model (DTM), digital surface model (DSM) and normalised DSM (nDSM = DSM-DTM), using GridSurface Create and Canopy Model functions in FUSION Version 3.50 (McGaughey, Pacific Northwest Research) [55]. The hillshade in grayscale (3D representation of the surface) with detailed profiles of the terrain were prepared based on the ALS data in ArcGIS (Esri).
Using FUSION software, the height of the vegetation was calculated (GridMetrics and CloudMetrics functions) as the value of the 95th percentile of the ALS point clouds relative altitude-a height below which is 95% of the whole analyzed points population. The standard deviation of the height and canopy cover (defined with values of 0%-100%) were also calculated. Visualizations of the vertical vegetation structure in the form of histograms were done using densitymetrics (FUSION)-information on the number of laser points reflected from the vegetation, in one-meter vertical intervals for the subsequent cells of the raster [55].

Results
The effects of processing the Sentinel-2 imagery and ALS point clouds are presented for the former sulfur mines of Machów and Jeziórko analysed areas. The first shows the LULC classes as a result of the image classification, then, the 2D and 3D parameters of the terrain and vegetation derived based on the ALS.
The morphometry characteristics of the terrain are presented as a DTM in the chosen color scale, from blue to red-for the lowest and highest values of the height above mean sea level (AMSL), respectively, and as a hillshade, in grayscale.
The parameters of vegetation, such as the height of vegetation (derived as 95th percentile), and the standard deviation of height and the canopy cover (value of 0%-100%), are presented as precise information about the spatial range of the vegetation and a visualization of the vertical vegetation structure. The parameters are presented as a raster map with a spatial resolution of 1.0 m.
The most important LULC class for the Machów area is broad-leaved forest, but significant value is also given to agricultural lands, according to an agricultural and forest type of reclamation that was carried out at this former sulfur mine. Class broad-leaved forest is 41.4% of the analysed area, coniferous forest is 1.7%, transitional woodland shrub is 17.6%; arable lands is 26.5%, pastures is 12.2%, and waters is 0.6%.  The morphometry characteristics of the Machów terrain derived based on ALS point cloud processing are presented in Figure 4, using a digital terrain model (DTM), hillshade, and detailed profiles of the spoil dump. The 2D area of the spoil dump is 891.47 ha and the 3D volume of the masses is 324.79 mln m 3 [58,59].  The most important LULC class for the Machów area is broad-leaved forest, but significant value is also given to agricultural lands, according to an agricultural and forest type of reclamation that was carried out at this former sulfur mine. Class broad-leaved forest is 41.4% of the analysed area, coniferous forest is 1.7%, transitional woodland shrub is 17.6%; arable lands is 26.5%, pastures is 12.2%, and waters is 0.6%.
The morphometry characteristics of the Machów terrain derived based on ALS point cloud processing are presented in Figure 4, using a digital terrain model (DTM), hillshade, and detailed profiles of the spoil dump. The 2D area of the spoil dump is 891.47 ha and the 3D volume of the masses is 324.79 mln m 3 [58,59].
The biggest total value of the LULC classes for the Machów analysed area are forested areas, so an important aim of the study was to derive detailed information about the spatial structure of the vegetation. This was done using ALS point clouds (2012) processing, as follows: height of vegetation (95th percentile), and standard deviation of the height and canopy cover (values of 0%−100%), presented in Figure 5 [58,59].
Remote Sens. 2020, 12, x FOR PEER REVIEW 8 of 20 The biggest total value of the LULC classes for the Machów analysed area are forested areas, so an important aim of the study was to derive detailed information about the spatial structure of the vegetation. This was done using ALS point clouds (2012) processing, as follows: height of vegetation (95th percentile), and standard deviation of the height and canopy cover (values of 0%−100%), presented in Figure 5 [58,59].

Jeziórko Sulfur Mine
The results of the Sentinel-2 image classification (2016), the LULC classification for the analysed area, are presented in Figure 6. The assessment parameters have the following values: AA = 86.17%, AR = 87.73%, and OA = 90.54% (Table 2) [11,56,57].  The most dominant LULC classes for the Jeziórko area are forested areas. Broad-leaved forest has a value of 52.6% of the analysed area, coniferous forest has 24.6%, transitional woodland shrub has 18.3%. The total value of the forested areas is 95.5%. Other classes are mineral extraction sites, which has 1.2%, and waters, which has 3.4%.
The morphometry characteristics of the terrain, derived based on ALS point cloud processing, are presented in Figure 7. The area is rather flat, with the lowest place being 146 m AMSL and the highest place being 154 m AMSL. The visualization, in the form of hillshade (Figure 7b), shows the effect of the reclamation works carried out at the Jeziórko sulfur mine, such as roads, drainage ditches, and slopes [60].  The most dominant LULC classes for the Jeziórko area are forested areas. Broad-leaved forest has a value of 52.6% of the analysed area, coniferous forest has 24.6%, transitional woodland shrub has 18.3%. The total value of the forested areas is 95.5%. Other classes are mineral extraction sites, which has 1.2%, and waters, which has 3.4%.
The morphometry characteristics of the terrain, derived based on ALS point cloud processing, are presented in Figure 7. The area is rather flat, with the lowest place being 146 m AMSL and the highest place being 154 m AMSL. The visualization, in the form of hillshade (Figure 7b), shows the effect of the reclamation works carried out at the Jeziórko sulfur mine, such as roads, drainage ditches, and slopes [60]. Detailed information about the spatial structure of the vegetation is presented in Figure 8 [11,60]. For the Jeziórko analysed area, we can observe the different stages of growth in the forested vegetation; for presentation, a different color scale than for Machow has been chosen to precisely show the differences in height vegetation. The parameters, derived based on ALS point clouds, showed precise information about the structure (3D) of the vegetation.  Detailed information about the spatial structure of the vegetation is presented in Figure 8 [11,60]. For the Jeziórko analysed area, we can observe the different stages of growth in the forested vegetation;

Discussion
The Jeziórko and Machów former sulfur mine areas are both examples of a dynamic increase in forested areas. For the LULC classes of broad-leaved forest, coniferous forest, and transitional woodland shrub, we can observe a dynamic change in growth. In previous studies [11][12][13], these areas showed an increase of spatial range in forested areas from the year 2000 to 2016, using image classification of Landsat 7 (2000), on-screen vectorization orthophoto (2009), Landsat 8 (2013), and the image classification of Sentinel-2 (2016).
The current LULC classes at the Machów and Jeziórko former sulfur mines, which are derived based on Sentinel-2 (2016, ESA) image processing, confirmed the applied type of reclamation in both areas. For Jeziórko, it was forestry, and for Machów, it was agroforestry [61][62][63][64]. The Jeziórko area is now almost fully covered by coniferous forest, broad-leaved forest, and transitional woodland shrub. At Machów, forested areas (broad-leaved forest and transitional woodland shrub) have the largest value, but there are also important agricultural lands − arable lands and pastures.
The total value of the LULC classes of coniferous forest, broad-leaved forest, and transitional woodland shrub in 2016 (Sentinel-2) get the following values: 95.5% for the Jeziórko analysed area, and 60.7% for Machów. For the Machów area, there are also important agricultural lands, as follows: arable lands and pastures, which covered a total of 38.7% of the analysed area according to the agroforestry type of reclamation for this area. According to the previous studies, based on Landsat 7 and Lansat 8 image processing [11][12][13], the increase in forested area for the period of time of 2000-2016 for Jeziórko was 13.3%, and for Machów was 14.6%. The forested areas in 2000 (Landsat 7) had a total value of 82.0% for Jeziórko, and 46.1% for Machów research area, and in 2013 (Landsat 8), Jeziórko was 93.8% and Machów was 50.5% [11][12][13].
Sentinel-2 images allowed for the correct identification of LULC classes (assessment above 90%). The results of the Sentinel-2 images' classification in the study were satisfactory, indicating that it is reasonable to automate the process of the classification of land cover and for monitoring the increase

Discussion
The Jeziórko and Machów former sulfur mine areas are both examples of a dynamic increase in forested areas. For the LULC classes of broad-leaved forest, coniferous forest, and transitional woodland shrub, we can observe a dynamic change in growth. In previous studies [11][12][13], these areas showed an increase of spatial range in forested areas from the year 2000 to 2016, using image classification of Landsat 7 (2000), on-screen vectorization orthophoto (2009), Landsat 8 (2013), and the image classification of Sentinel-2 (2016).
The current LULC classes at the Machów and Jeziórko former sulfur mines, which are derived based on Sentinel-2 (2016, ESA) image processing, confirmed the applied type of reclamation in both areas. For Jeziórko, it was forestry, and for Machów, it was agroforestry [61][62][63][64]. The Jeziórko area is now almost fully covered by coniferous forest, broad-leaved forest, and transitional woodland shrub. At Machów, forested areas (broad-leaved forest and transitional woodland shrub) have the largest value, but there are also important agricultural lands-arable lands and pastures.
The total value of the LULC classes of coniferous forest, broad-leaved forest, and transitional woodland shrub in 2016 (Sentinel-2) get the following values: 95.5% for the Jeziórko analysed area, and 60.7% for Machów. For the Machów area, there are also important agricultural lands, as follows: arable lands and pastures, which covered a total of 38.7% of the analysed area according to the agroforestry type of reclamation for this area. According to the previous studies, based on Landsat 7 and Lansat 8 image processing [11][12][13], the increase in forested area for the period of time of 2000-2016 for Jeziórko was 13.3%, and for Machów was 14.6%. The forested areas in 2000 (Landsat 7) had a total value of 82.0% for Jeziórko, and 46.1% for Machów research area, and in 2013 (Landsat 8), Jeziórko was 93.8% and Machów was 50.5% [11][12][13].
Sentinel-2 images allowed for the correct identification of LULC classes (assessment above 90%). The results of the Sentinel-2 images' classification in the study were satisfactory, indicating that it is reasonable to automate the process of the classification of land cover and for monitoring the increase in forested areas. According to papers using Sentinel images [31][32][33][34] and preparing terrain information for reclaimed areas using remote sensing data [7][8][9][65][66][67][68][69], research has confirmed the possibility of using Sentinel-2 images for LULC change detection and for the monitoring of vegetated areas in reclaimed areas.
Remote sensing materials and automated procedures of processing were indicated in research for finding the possibility of monitoring post-industrial areas, mainly in terms of the objectivity of the obtained results of land cover classification and the spatial structure (2D and 3D) of the vegetation. Analyses can be done at any time interval to analyze changes (4D analyses), according to the revisit time of the satellites and the ALS data availability-processing allows for obtaining a detailed LULC classification in a semi-automated way. It opens up possibilities in monitoring the progress of the growth spatial range of vegetation areas at any time interval, which is an important step in the assessment of the results from a carried-out reclamation. Fusing Sentinel-2 images and ALS point clouds gives possibilities for defining LULC changes and precise information about the spatial characteristics of vegetation on reclaimed areas by afforestation [11].
The parameters from the processed ALS point clouds in this research showed a variation in the height of the vegetation and canopy cover. It is important that we have precise information about the height of the vegetation at the Machów and Jezioróko analysed area. The automation of the processes for detecting and monitoring forested areas for the analysed areas is important and vital, because of the control process effects of the reclamation areas of former mines [9,11,70,71].
According to studies on Jeziórko and Machów, particularly for the Jeziórko area, an increase in forested areas was shown. For Jeziórko, a test site analysis of ALS point clouds suggests a significant variation in the height of the vegetation and canopy cover. Jeziórko was a heavily degraded area, in which there are still the remains of sulfur mines, and a graphical and spatial view of the vegetation structure shows differences in vegetation growth. This indicates an ongoing process of vegetation development, as an effect of the reclamation treatment for this area. Frasch's method of sulfur exploitation caused geochemical, ground, and hydrology transformations [51,52].
The area after sulfur mining is characterized by difficult conditions for reclamation, so the monitoring of vegetation growth for this area is very important. An integration of the results of the Sentinel-2 image classification and LiDAR point clouds processing gives complementary and objective information about the distribution of the LULC classes. The spatial range and structure of the vegetation are precisely described. Geostatistical and geochemical analyses are used as complementary research.
To comprehensively assess the current state of the restored ecosystem after sulfur extraction, environmental components such as soil, surface water, the reaction of trees and herbaceous plants to a high sulfur concentration in soil, and plant nutrients have been examined. Soil contamination and plant reactions to contamination were assessed in two ways: spatially in a regular square grid sample points arrangement, covering above 200 ha of the reclaimed area [52], and in the reductionist approach of studying plots representing various categories of land plant cover [51,54]. The water chemistry was analyzed in the points located on the ponds and resivoirs in seasonal variations [53]. An examination of the abovementioned elements of the environment allowed for a comprehensive assessment of the state of the restored ecosystem.
LiDAR point cloud processing provides accurate information about the spatial and temporal distribution of LULC classes, and shows the spatial range and structure of the vegetation. Point clouds derived from laser scanning via an unmanned aerial vehicle (UAV) platform [72], or generated using, for example, a stereo-matching method from UAV imagery, could also be employed for such purposes [73][74][75]. Because of the use of LiDAR data-satellite (SLS), airborne (ALS), unmanned (ULS), or terrestrial (TLS) laser scanning-an exact assessment of the vegetation connected with the spatial distribution of the point cloud is possible. These indicators are often defined to meet the needs of planning and inventory, as well as for mapping plant associations. Geoinformation technologies show great potential for carrying out large area studies of the spatial vegetation structure.
An assessment of the LiDAR point clouds for the automation of the mapping range and structure of vegetation in forested areas is very important. In 2018, new satellite laser scanning missions began, such as global ecosystem dynamics investigation (GEDI) and ice, cloud, and land elevation Satellite-2 (ICESat-2), meaning that we can also test the possibilities of using data from these satellite LiDAR for detecting and monitoring forested areas. GEDI provides high-quality laser ranging observations of the Earth's forests and topography. GEDI is mounted on the Japanese Experiment Module's Exposed Facility (JEM-EF), and provides the first high-resolution observations of a forest vertical structure at a global scale [76]. ICESat-2 was launched in September 2018, and became the highest-resolution laser altimeter ever to be operated from space. The satellite is now measuring the height of the Earth's surfaces in remarkable detail. The satellite collects detailed elevation measurements over tropical and temperate latitudes, providing a remarkable look at the heights of the land and ocean features. The advanced topographic laser altimeter system (ATLAS) on ICESat-2 measures the elevation by sending pulses of light to the Earth's surface. It then measures, to within a billionth of a second, how long it takes individual photons to return to the sensor. Each dot on the visualization above represents a photon detected by ATLAS. Most of the dots in this "photon cloud" are clustered around a surface, whether a tree top, the ground, or waves in the ocean [77].

Conclusions
Post-mining areas are characterized by a dispersion in land cover classes and a diverse spatial structure of the formed vegetation. Monitoring the vegetation development is very significant for these areas. The aspect of monitoring the post-mining areas is directly connected with the constant need for precise geometric and attribute data, which can be obtained as a result of the application of remote sensing technologies and then integrated into a GIS system to generate new information with the application of spatial analyses 2D/3D. This study showed a difference in the spatial range and structure of vegetation at the forested areas, which grows on the reclaimed areas' former sulfur mines. The study highlighted the possibility of updating the LULC classes in terms of the identification and monitoring of reclaimed areas, with the processing of Sentinel-2 and LiDAR point clouds. In the presented study, the collected ALS point clouds show significant differences in the spatial structure of the vegetation. This diversity was visible in the surface size (2D) and vertical vegetation structure (3D). Differentiated vertical structures of vegetation indicate a long-lasting process of forest regrowth in reclaimed areas, using LiDAR point clouds allows for wider and more precise definitions of the spatial structure of vegetation. Furthermore, the application of the processed point clouds facilitates the objective and relatively accurate assessment of the spatial characteristics of the vegetation overgrowing in reclaimed areas, for example, its height above ground and canopy cover.