Rock Location and Quantitative Analysis of Regolith at the Chang ’ e 3 Landing Site Based on Local Similarity Constraint

Structural analysis of lunar regolith not only provides important information about lunar geology but also provides a reference for future lunar sample return missions. The Lunar Penetrating Radar (LPR) onboard China’s Chang’E-3 (CE-3) provides a unique opportunity for mapping the subsurface structure and the near-surface stratigraphic structure of the regolith. The problem of rock positioning and regolith-basement interface highlighting is meaningful. In this paper, we propose an adaptive rock extraction method based on local similarity constraints to achieve the rock location and quantitative analysis for regolith. Firstly, a processing pipeline is designed to image the LPR CH-2 A and B data. Secondly, we adopt an f-x EMD (empirical mode decomposition)-based dip filter to extract low-wavenumber components in the two data. Then, we calculate the local similarity spectrum between the filtered CH-2 A and B. After a soft threshold function, we pick the local maximums in the spectrum as the location of each rock. Finally, according to the extracted result, on the one hand, the depth of regolith is obtained, and on the other hand, the distribution information of the rocks in regolith, which changes with the path and the depth, is also revealed.


Introduction
Chang'E-3 landed at 340.4875 • E, 44.1189 • N on the Moon on 14 December 2013 in a new region that has not been explored before in the largest basin-the Mare Imbrium [1].The dual-frequency Lunar Penetrating Radar aboard the Yutu Rover provides a unique opportunity to map the subsurface structure to a depth of several hundreds of metres from the low-frequency channel (CH-1, 60 MHz) and the near-surface stratigraphic structure of the regolith from the high-frequency channel (CH-2A &CH-2B, 500 MHz).The LPR also provides an accurate detection result with high resolution from high-frequency observations [2].
LPR data processing and initial results were first presented by NAOC [3].Initial analysis of the LPR observations, especially that from the CH-1, indicates that there are more than nine subsurface layers from the surface to a depth of ~360 m [1].The onboard Lunar Penetrating Radar conducted a 114-m-long profile, which measured a thickness of ~5 m of the lunar regolith layer and detected three underlying basalt units at depths of 195, 215, and 345 m.The radar measurements suggest an underestimation of the global lunar regolith thickness by other methods and reveal a vast volume from the last volcanic eruption [4].Fa et al., Lai et al. and Zhang et al. speculated the near surface structure by processing the raw CH-2B data [5][6][7].Dong et al. and Zhang et al. calculated the parameters of the regolith [8,9].
The previous papers mainly studied the geological stratification and parameter inversion of regolith by using CH-2B data.The quantity and location of rocks in regolith have not been researched and CH-2A data have not been fully used.The quantity and location of rocks in regolith not only help to understand the evolution of regolith on the landing site but also provide a priori information for the further CE-5 plan of regolith collection.The rocks in lunar regolith are the break point, causing diffractions in LPR data.The kinematics characteristics of these diffractions are quite different from those of main reflections, which is expressed as a hyperbola in common offset sections [10,11].The vertex position of the diffractions indicates the location of rocks.Therefore, to reach this goal, a method for extracting low-wavenumber components of diffractions and taking full advantages of both LPR CH-2A and CH-2B data is needed.
Huang et al. [12] uses empirical mode decomposition (EMD) to prepare stable input for the Hilbert transform.The aim of EMD is stabilizing a nonstationary signal and decomposing the nonstationary signal into fast and slow oscillation components, called intrinsic mode functions (IMFs).1D EMD can be an adaptive band-pass filter, dividing the dataset into the IMFs with different frequency range.As the property of EMD, Bekara and van der Baan [13] propose f-x EMD to attenuate the random and coherent noise.Cai et al. [14] propose the guideline of t-f-x EMD denoising.Chen et al. [15] add an autoregressive (AR) model to f-x EMD to improve the applicable conditions and adopt f-x EMD as an effective tool for dip filter.
Local similarity is a typical local attribute and promising for quantifying the similarity of two datasets in a non-instantaneous and non-global manner [16].Different from traditional attributes, it is calculated using every element of the LPR data and its adjoining elements within a definite scope, which has been utilized in many signal processing fields such as image contrast [17,18], time-frequency analysis [19], noise attenuation [20,21], deblending [22].The basic criterion of image contrast in this method is the different similarity between signal and noise, i.e., the signal denotes a large value in the local similarity spectrum.In this way, noise and artifacts can be attenuated by using a threshold function.
In this paper, we propose an adaptive rock extraction method based on local similarity constrains to achieve the rock location and quantitative analysis for regolith.Firstly, a processing pipeline is designed to image the LPR CH-2 A and B data.Secondly, we adopt f-x EMD-based dip filter to extract low-wavenumber components in the two data.Then, we calculate the local similarity spectrum between the filtered CH-2 A and B. After a soft threshold function, we pick the local maximums in the spectrum as the location of each rock.Finally, according to the extracted result, on the one hand, the depth of regolith is obtained, and on the other hand, the distribution information of the rocks in regolith, which changes with the path and the depth, is also revealed.

LPR Data Processing
Yutu Rover released by CE-3 was the first soft landing on the Moon since the Soviet Union's Luna 24 mission in 1976.To be specific, the Yutu rover explored the surface and subsurface of the landing site in the northern part of the Mare Imbrium using its four main instruments: the Panoramic Camera, Lunar Penetrating Radar (LPR), Visible-Near Infrared Spectrometer (VNIS), and Active Particle-Induced X-ray Spectrometer (APXS).Its track extends to 114.8 m (Figure 1) near a young crater.In this part, the data processing results of the LPR are reported.Aiming at the near-surface stratigraphic structure of the regolith, CH-2 antenna is selected.The CH-2 antenna is mounted at the bottom of lunar rover (Figure 2a), which is about 30 cm away from the ground.Figure 2b shows the structure of the CH2 antenna.As can be seen from the figure, the CH2 antenna has three antenna elements.The antenna elements are arranged side by side in a metal back cavity which is divided into three individual cavities.One antenna element is used to transmit EM waves and the other two are used to receive the EM waves.Each antenna element is 336 mm in length and 120 mm in width, and the space between the antenna elements is about 160 mm.The height of the back cavity of the antenna is reduced to 22 mm from a quarter of the center wavelength in order to ensure the lunar rover can maneuver over obstacles [2].Aiming at the near-surface stratigraphic structure of the regolith, CH-2 antenna is selected.The CH-2 antenna is mounted at the bottom of lunar rover (Figure 2a), which is about 30 cm away from the ground.Figure 2b shows the structure of the CH2 antenna.As can be seen from the figure, the CH2 antenna has three antenna elements.The antenna elements are arranged side by side in a metal back cavity which is divided into three individual cavities.One antenna element is used to transmit EM waves and the other two are used to receive the EM waves.Each antenna element is 336 mm in length and 120 mm in width, and the space between the antenna elements is about 160 mm.The height of the back cavity of the antenna is reduced to 22 mm from a quarter of the center wavelength in order to ensure the lunar rover can maneuver over obstacles [2].Aiming at the near-surface stratigraphic structure of the regolith, CH-2 antenna is selected.The CH-2 antenna is mounted at the bottom of lunar rover (Figure 2a), which is about 30 cm away from the ground.Figure 2b shows the structure of the CH2 antenna.As can be seen from the figure, the CH2 antenna has three antenna elements.The antenna elements are arranged side by side in a metal back cavity which is divided into three individual cavities.One antenna element is used to transmit EM waves and the other two are used to receive the EM waves.Each antenna element is 336 mm in length and 120 mm in width, and the space between the antenna elements is about 160 mm.The height of the back cavity of the antenna is reduced to 22 mm from a quarter of the center wavelength in order to ensure the lunar rover can maneuver over obstacles [2].As the tight arrangement of the antennas, two sets of 500 MHz data (CH-2A & CH-2B) are achieved and their data quality should be similar.However, due to the complex acquisition environment and inappropriate instrument parameter settings, the CH-2A data has a lower SNR (signal-to-noise ratio) than the CH-2B data.Therefore, the former papers only focused on the CH-2B data.In order to make full use of CH-2A and CH-2B data, according to the acquisition parameters, the actual situation, and the data quality, the LPR data processing pipeline is designed (Figure 3).Note that the non-uniform patrol mode and uninterrupted collection of the rover cause the problem of uneven sampling.After data editing and processing, the high-resolution radar images with 497 samples, 4595 traces and 0.02 m spatial interval are accessible.The IDs for the data from Lunar Penetrating Radar are listed in Appendix A in the Supporting Materials.As the tight arrangement of the antennas, two sets of 500 MHz data (CH-2A & CH-2B) are achieved and their data quality should be similar.However, due to the complex acquisition environment and inappropriate instrument parameter settings, the CH-2A data has a lower SNR (signal-to-noise ratio) than the CH-2B data.Therefore, the former papers only focused on the CH-2B data.In order to make full use of CH-2A and CH-2B data, according to the acquisition parameters, the actual situation, and the data quality, the LPR data processing pipeline is designed (Figure 3).Note that the non-uniform patrol mode and uninterrupted collection of the rover cause the problem of uneven sampling.After data editing and processing, the high-resolution radar images with 497 samples, 4595 traces and 0.02 m spatial interval are accessible.The IDs for the data from Lunar Penetrating Radar are listed in Appendix A in the Supporting Materials.The previous papers mainly studied on the geological stratification and parameter inversion.The quantity and location of rocks in regolith have not been researched.The quantity and location of rocks in regolith not only help to understand the evolution of regolith on the landing site but also provide a priori information for the further CE-5 plan of regolith collection.In the following method, we propose a rock extraction method based on local similarity constrains to achieve the rock location and quantitative analysis for regolith.

An f-x Domain EMD-Based Dip Filter
EMD can provide an empirical decomposition of a non-stationary signal.These decomposed sub-signals are separated based on oscillation frequency and called IMFs.A stable IMF has a constant instantaneous frequency and narrow-band waveform, satisfying two conditions [12]: (1) the number of extremes and zero crossings in the data series are either equal or differ by one, and (2) at any points, the mean value of the envelope defined by the local maxima and the local minima is zero.The previous papers mainly studied on the geological stratification and parameter inversion.The quantity and location of rocks in regolith have not been researched.The quantity and location of rocks in regolith not only help to understand the evolution of regolith on the landing site but also provide a priori information for the further CE-5 plan of regolith collection.In the following method, we propose a rock extraction method based on local similarity constrains to achieve the rock location and quantitative analysis for regolith.

An f-x Domain EMD-Based Dip Filter
EMD can provide an empirical decomposition of a non-stationary signal.These decomposed sub-signals are separated based on oscillation frequency and called IMFs.A stable IMF has a constant instantaneous frequency and narrow-band waveform, satisfying two conditions [12]: (1) the number of extremes and zero crossings in the data series are either equal or differ by one, and (2) at any points, the mean value of the envelope defined by the local maxima and the local minima is zero.
In the 1D case, the signal is decomposed into several sub-signals c n (t) with different frequency ranges, which can be written as where s(t) is the input signal and u n (t) is the decomposed IMFs.r(t) denotes the residual and N is the IMF number.
As the advantages of signal decomposition, Bekara and van der Baan [13] adopt EMD in f-x domain to suppress random noise and steep dip coherent noise.They consider the noise energy is dominant in the high wavenumber portion in the f-x domain.The high wavenumber portion presents the fast oscillation of each frequency slice.Based on the separation between the noise and signal, noise can be attenuated by simply removing IMF1 from noisy data.The detailed process is shown as follows: (1) Set the size of the time window.
(2) Pick a time window and adopt 1D forward Fourier transform along the time direction.
(3) Pick a frequency slice and separate it into real and imaginary parts.(4) Compute IMF1s for real and imaginary parts to obtain the filtered parts.
The two advantages of f-x EMD are convenience and stability.The f-x EMD is a data-driven f-k filter and does not require the predefined muting zone in the f-k domain, which is easily embedded into field data processing.Moreover, unlike convolutional operator-based denoising methods (such as f-x predictive filter), f-x EMD can deal with an irregular spatial sampling dataset [13,23].For data acquisition of LPR, irregular spatial sampling is inevitable because of the complex terrain, finite time and expensive cost.Therefore, f-x EMD is a promising tool in LPR data processing.
It should also be noted that the choice of the removed IMFs can be more than one.The choice is determined by dispersion of high wavenumber components and noise level.When the target noise is located in high wavenumber components or the noise level is low, the number of removed IMFs can be small.Conversely, more IMFs should be removed.
Since the dip angle of the signal is related to wavenumber, f-x EMD can be used as a dip filter [15].The different IMFs present different dip angle ranges, i.e., high dip components locate in the low IMFs and low dip components locate in the high IMFs.If we divide the IMF set into several subsets, the dataset is separated by the dip angle.Therefore, we define the dip filter using f-x EMD as follows: where Λ( f , x) is the filtered frequency slice and u i ( f , x) is the ith separated IMF.D i is the ith dip subsets and m is the number of divided subsets.ε i denotes the weighting factors.Figure 4 demonstrates the results of three types of dip filters (high-pass, mid-pass and low-pass) working on a plane wave model.In the synthetic data (Figure 4a), the dataset contains three dip sets.After the three dip filters, different dip events (Figure 4b-d) are well extracted.Table 1 shows the detailed parameters of the three filters.The LPR data are acquired in a constant-offset way, whose source can be considered as wave plane.The kinematics characteristics of the main reflection events are similar to that of the terrain.The rock in lunar regolith is the break point, causing diffractions in LPR data.The kinematics characteristics of these diffractions are hyperbola.In a word, the reflection events are low dip and smooth, whereas the diffraction events show a high dip.The diffraction point extraction can be transformed into a problem of steep dip decreasing.Therefore, we should select a simple low-pass dip filter, with m = 0, The key parameter is the number of removed IMFs p.
Remote Sens. 2019, 11, x FOR PEER REVIEW 6 of 21 reflection events are similar to that of the terrain.The rock in lunar regolith is the break point, causing diffractions in LPR data.The kinematics characteristics of these diffractions are hyperbola.In a word, the reflection events are low dip and smooth, whereas the diffraction events show a high dip.The diffraction point extraction can be transformed into a problem of steep dip decreasing.Therefore, we should select a simple low-pass dip filter, with 0 m = , 1 0 . The key parameter is the number of removed IMFs p .

Rock Extraction Based on Local Similarity Constraint
For quantitative analysis, the problem of rock positioning is commonly picking the local maximums in the filtered data.However, as shown in Figure 2

Rock Extraction Based on Local Similarity Constraint
For quantitative analysis, the problem of rock positioning is commonly picking the local maximums in the filtered data.However, as shown in Figure 2, the preprocessed LPR CH-2 A and B data are interfered with by noise.The strong coherence of noise leads to many noise-caused local maximums, which reduces the accuracy of rock extraction.To take full advantages of both LPR CH-2A and CH-2B data and reduce the effects of noise, we introduce local similarity (see Appendix B) in the process of rock positioning.The basic idea is the similarity difference between the signal and noise in two similar datasets.We consider the two noisy datasets (D) are a totalization of noise (N) and signal (S): The noise is caused by ambient disturbance, instrument defect, etc., which has little relationship with underground structure, and the signal is just the opposite.In a word, if the observing system is the same, the signal will have larger similarity than the noise.We calculate the local similarity spectrum between the two data points to quantify the difference in similarity.We consider the local similarity (c) between two noisy datasets as and Equation ( 6) can be easily modified as We utilize a soft threshold function modifies to attenuate the noise interference.We obtain an approximate signal-dominated local similarity spectrum: where ε is the threshold value and i, j is the sample coordinates in the time-space domain.
In Figure 5, we add noise with different noise levels into the same data (Figure 4a) to obtain two noisy datasets with similar useful signal (Figure 5a,b).The added noise is Gaussian random noise and the distribution is N(µ, σ) =N(0, 0.001) and N(µ, σ) =N(0, 0.0003) , respectively.Then, we calculate the similarity spectrum (Figure 5c) between the two noisy data and apply a soft threshold function to it.In this spectrum, we observe a large similarity difference between signal and noise.After the soft thresholding, the spectrum highlights the useful signal.
According to the property of local similarity, we propose a rock-extracting method based on local similarity constraint.The detailed workflow is shown as follows: (1) For LPR CH-2A and B data

Verification of Simulation Result
In order to validate the effectiveness of the proposed method, a complex model (Figure 6a) is built.This synthetic model considers many factors referenced from [24][25][26]: random medium, undulating interface, and anomalous body.FDTD is applied for the simulation of the simple model [27].According to the actual acquisition parameters of LPR [2], the simulated parameters are shown in Table 2.The forward results are obtained in Figure 6b,c.

Verification of Simulation Result
In order to validate the effectiveness of the proposed method, a complex model (Figure 6a) is built.This synthetic model considers many factors referenced from [24][25][26]: random medium, undulating interface, and anomalous body.FDTD is applied for the simulation of the simple model [27].According to the actual acquisition parameters of LPR [2], the simulated parameters are shown in Table 2.The forward results are obtained in Figure 6b,c.
In the forward results (Figure 5b,c), there are two types of useful signals, i.e., reflections (0-6 and 60-80 ns) and diffractions (10-60 ns).Since our focus is rock positioning, we mute the shallow reflections before the dip filter.
Figure 7 demonstrates the results of the dip filter.After the f-x EMD-based low-pass dip filter, the steep-dip components are well attenuated.For diffractions, the positions of filtered components are consistent with their corresponding vertex positions.We also see some noise residual in the filtered data, leading to many noise-caused local maximums.5b,c), there are two types of useful signals, i.e., reflections (0-6 and 60-80 ns) and diffractions (10-60 ns).Since our focus is rock positioning, we mute the shallow reflections before the dip filter.Figure 8 demonstrates the local similarity spectrum between the two filtered datasets after soft thresholding and the result of rock positioning.The spectrum is clean and signal-dominated, proving the effectiveness of our method; the energy group denotes the useful signal.Note that reflection energy in the spectrum also leads to unexpected rock extraction.Before local maximum picking, we mute the deep reflection energy (arrows in Figure 8a) and the muted results are shown in Figure 8b. Figure 8c demonstrates the result of rock positioning.
Figure 7 demonstrates the results of the dip filter.After the f-x EMD-based low-pass dip filter, the steep-dip components are well attenuated.For diffractions, the positions of filtered components are consistent with their corresponding vertex positions.We also see some noise residual in the filtered data, leading to many noise-caused local maximums.Figure 8 demonstrates the local similarity spectrum between the two filtered datasets after soft thresholding and the result of rock positioning.The spectrum is clean and signal-dominated, proving the effectiveness of our method; the energy group denotes the useful signal.Note that reflection energy in the spectrum also leads to unexpected rock extraction.Before local maximum picking, we mute the deep reflection energy (arrows in Figure 8a) and the muted results are shown in Figure 8b. Figure 8c demonstrates the result of rock positioning.In order to evaluate the effect of rock positioning, we compare the result with the integrated regolith model (Figure 6a).From Figure 9, we see that most of the rocks are effectively extracted and their position is consistent with the model and a few rocks are unextracted and over extracted.In order to evaluate the effect of rock positioning, we compare the result with the integrated regolith model (Figure 6a).From Figure 9, we see that most of the rocks are effectively extracted and their position is consistent with the model and a few rocks are unextracted and over extracted.We use three concepts (detection rate, missed detection rate and false alarm rate) to evaluate the result of rock positioning quantitatively.
(1) The detection rate det R is the probability that a rock block can be detected and is expressed by: where det N is the number of the rocks which can be detected, all N is the total number of rocks.
(2) The rate of missed detection mis R is the probability that a rock block cannot be detected.It is expressed by: where mis N is the number of the rocks which cannot be detected, all N is the total number of rocks.
(3) The false alarm rate fal R is the probability that a non-existent rock is detected.It is  We use three concepts (detection rate, missed detection rate and false alarm rate) to evaluate the result of rock positioning quantitatively.
(1) The detection rate R det is the probability that a rock block can be detected and is expressed by: where N det is the number of the rocks which can be detected, N all is the total number of rocks.
(2) The rate of missed detection R mis is the probability that a rock block cannot be detected.It is expressed by: where N mis is the number of the rocks which cannot be detected, N all is the total number of rocks.
(3) The false alarm rate R f al is the probability that a non-existent rock is detected.It is expressed by: where N f al is the number of the detected rocks which are non-existent,N all is the total number of rocks.The detection rate of the above-mentioned forward result is R det = 92.105%, the missed detection rate is R mis = 7.895%, and the false alarm rate is R f al = 68.421%.It can be seen that our method has a high detection rate and a low missed detection rate.The reason for missed detection is that the rock is close to the reflector so that the diffractions are interfered with by reflections.The false alarm rate is relatively high; there are two main reasons for the excessive extraction of rocks: (1) In the rock enrichment area (9-13 m), diffraction interferences decrease the accuracy of local maximum picking; (2) bigger rocks allow the diffractions generated by their upper and lower interfaces to be recognized, which generates serval "rock pairs" (red circle) in extracted results.After removing these "rock pairs", the actual false alarm rate drops to 23.684%.Although there are a few errors in the extraction results, the rock distribution is close to the model, which is acceptable for the rock analysis.

LPR Data Result
After proving the effectiveness of our proposed method, we process the LPR CH-2 data.The results of the dip filter are shown in Figure 10 and the corresponding local similarity spectra are shown in Figure 11a.From Figure 10, we see that most diffractions locate in 15-118 ns.The muted spectrum is shown in Figure 11b.Then, we utilize the result of rock positioning (Figure 12) to research the evolution of regolith on the landing site.
Remote Sens. 2019, 11, x FOR PEER REVIEW 13 of 21 interfaces to be recognized, which generates serval "rock pairs" (red circle) in extracted results.After removing these "rock pairs", the actual false alarm rate drops to 23.684% .Although there are a few errors in the extraction results, the rock distribution is close to the model, which is acceptable for the rock analysis.

LPR Data Result
After proving the effectiveness of our proposed method, we process the LPR CH-2 data.The results of the dip filter are shown in Figure 10 and the corresponding local similarity spectra are shown in Figure 11a.From Figure 10, we see that most diffractions locate in 15-118 ns.The muted spectrum is shown in Figure 11b.Then, we utilize the result of rock positioning (Figure 12) to research the evolution of regolith on the landing site.

Discussion
After we obtained the result of rock positioning for LPR data, we divided the layers according to the distribution of the rocks, as shown in Figure 13.The base rock layer is basalt, which is the product of the last basalt covering.The regolith layer contains a lot of rock fragments.The depth of regolith is 5 m at minimum and 10 m at maximum.The stratified result is consistent with previous results [5][6][7].The dielectric constant is critical for time-depth conversion.The permittivity of lunar regolith is influenced by density and ilmenite concentrations [28][29][30].Many measurements have been investigated using lunar regolith samples from the Apollo & Luna era; the relative dielectric constant of Surveyor regolith samples ranges from 2.00 to 3.28 [31] and the relative dielectric constant of Luna regolith samples ranges from 1.7 to 4.4 [32,33].More recently, microwave remote sensing was used to estimate the dielectric constant of regolith [34,35].

Discussion
After we obtained the result of rock positioning for LPR data, we divided the layers according to the distribution of the rocks, as shown in Figure 13.The base rock layer is basalt, which is the product of the last basalt covering.The regolith layer contains a lot of rock fragments.The depth of regolith is 5 m at minimum and 10 m at maximum.The stratified result is consistent with previous results [5][6][7].

Discussion
After we obtained the result of rock positioning for LPR data, we divided the layers according to the distribution of the rocks, as shown in Figure 13.The base rock layer is basalt, which is the product of the last basalt covering.The regolith layer contains a lot of rock fragments.The depth of regolith is 5 m at minimum and 10 m at maximum.The stratified result is consistent with previous results [5][6][7].The dielectric constant is critical for time-depth conversion.The permittivity of lunar regolith is influenced by density and ilmenite concentrations [28][29][30].Many measurements have been investigated using lunar regolith samples from the Apollo & Luna era; the relative dielectric constant of Surveyor regolith samples ranges from 2.00 to 3.28 [31] and the relative dielectric constant of Luna regolith samples ranges from 1.7 to 4.4 [32,33].More recently, microwave remote sensing was used to estimate the dielectric constant of regolith [34,35].The dielectric constant is critical for time-depth conversion.The permittivity of lunar regolith is influenced by density and ilmenite concentrations [28][29][30].Many measurements have been investigated using lunar regolith samples from the Apollo & Luna era; the relative dielectric constant of Surveyor regolith samples ranges from 2.00 to 3.28 [31] and the relative dielectric constant of Luna regolith samples ranges from 1.7 to 4.4 [32,33].More recently, microwave remote sensing was used to estimate the dielectric constant of regolith [34,35].Fa et al., Dong et al. and Feng et al. report the estimated results of the lunar regolith permittivity in the CE-3 landing area using the LPR are 3.0 ± 0.03, 2.9 ± 0.4 and ~3, respectively [5,8,36].Therefore, we set the relative dielectric constant to 3.0 as an appropriate value for time-depth conversion in the processing pipeline (Figure 3).
To estimate the depth error, we need to set the range of the dielectric constant.Based on previous research results [5,8,36] and including all dielectric constant estimates, we believe that ε r = 3.0 ± 0.5 is a suitable range of dielectric constant variation.After counting and analysing the extracted rocks, we obtain their space location, time, and depth position (Appendix C) for different dielectric constants (ε r = 2.5, 3.0, 3.5).When ε r = 3.0 ± 0.5, the error of the position estimation is less than 10% (−9.62% to 7.36%), and the maximum error values are −0.87 and 0.67 m.In the same way, we estimate the position of the interface.When ε r = 3.0 ± 0.5, the average estimated depth of lunar regolith is estimated to be 7.5 +0.71 −0.60 m.Moreover, we can also obtain the distribution information of the rocks in regolith which changes with the path and the depth.Figure 14 is a scatterplot of the rock number and location at each 5 m.The figure shows us a relationship between the number of rocks and distance.There is a minimum value at 5-10 m, 30-35 m, 75-80 m and 85-90 m where the number is less than 1.The mission will drill and collect the regolith from the moon [37], which requires that there is no rock below the drilling point, otherwise the drilling machine will be damaged.The scatterplot can help us select the drilling point.
Feng et al. report the estimated results of the lunar regolith permittivity in the CE-3 landing area using the LPR are 3.0 ± 0.03, 2.9 ± 0.4 and ~3, respectively [5,8,36].Therefore, we set the relative dielectric constant to 3.0 as an appropriate value for time-depth conversion in the processing pipeline (Figure 3).
To estimate the depth error, we need to set the range of the dielectric constant.Based on previous research results [5,8,36] and including all dielectric constant estimates, we believe that ε = ± 3.0 0.5 r is a suitable range of dielectric constant variation.After counting and analysing the extracted rocks, we obtain their space location, time, and depth position (Appendix C) for different dielectric constants ( ε = 2.5, 3.0, 3.5 Moreover, we can also obtain the distribution information of the rocks in regolith which changes with the path and the depth.Figure 14 is a scatterplot of the rock number and location at each 5 m.The figure shows us a relationship between the number of rocks and distance.There is a minimum value at 5-10 m, 30-35 m, 75-80 m and 85-90 m where the number is less than 1.The Chang'E-5 mission will drill and collect the regolith from the moon [37], which requires that there is no rock below the drilling point, otherwise the drilling machine will be damaged.The scatterplot can help us select the drilling point.In the same way, the analysis between the number of rocks and depth has been performed in Figure 15.There is a maximum value at ~5 m.The above stratified analysis tells us that the depth of regolith is 5 m at minimum and 10 m at maximum.From 5 m, the interface appears, and the number of rocks is decreasing.The tendency in Figure 15 is consistent with the stratigraphic structure at the CE-3 landing site.In the same way, the analysis between the number of rocks and depth has been performed in Figure 15.There is a maximum value at ~5 m.The above stratified analysis tells us that the depth of regolith is 5 m at minimum and 10 m at maximum.From 5 m, the interface appears, and the number of rocks is decreasing.The tendency in Figure 15 is consistent with the stratigraphic structure at the CE-3 landing site.

Conclusions
The LPR equipped on the Yutu Rover detected the lunar geological structure in the Northern Imbrium.A data preprocessing pipeline is designed to solve some types of issues, such as repeated

Figure 1 .
Figure 1.Yutu's path on the Moon.The context image was taken by the descent camera on the CE-3 lander.The red star shows the landing site.The blue line shows the path.

Figure 2 .
Figure 2. (a) The position of CH-2 antenna on the rover (b) The structure of the CH2 antenna.

Figure 1 .
Figure 1.Yutu's path on the Moon.The context image was taken by the descent camera on the CE-3 lander.The red star shows the landing site.The blue line shows the path.

21 Figure 1 .
Figure 1.Yutu's path on the Moon.The context image was taken by the descent camera on the CE-3 lander.The red star shows the landing site.The blue line shows the path.

Figure 2 .
Figure 2. (a) The position of CH-2 antenna on the rover (b) The structure of the CH2 antenna.Figure 2. (a) The position of CH-2 antenna on the rover (b) The structure of the CH2 antenna.

Figure 2 .
Figure 2. (a) The position of CH-2 antenna on the rover (b) The structure of the CH2 antenna.Figure 2. (a) The position of CH-2 antenna on the rover (b) The structure of the CH2 antenna.

Table 1 .Figure 4 .
Figure 4. Demonstration of dip filter using f-x EMD.(a) The synthetic data, (b) high-pass dip filtered data, (c) mid-pass dip filtered data, (d) low-pass dip filtered data.
, the preprocessed LPR CH-2 A and B data are interfered with by noise.The strong coherence of noise leads to many noise-caused local maximums, which reduces the accuracy of rock extraction.To take full advantages of both LPR CH-2A and CH-2B data and reduce the effects of noise, we introduce local similarity (see Appendix B) in the process of rock positioning.The basic idea is the similarity difference between the signal

Figure 4 .
Figure 4. Demonstration of dip filter using f-x EMD.(a) The synthetic data, (b) high-pass dip filtered data, (c) mid-pass dip filtered data, (d) low-pass dip filtered data.

( 2 )
steep-dip components by an f-x EMD-based low-pass dip filter.Calculate local similarity spectrum between LPR CH-2A and B data.(3) Utilize a soft threshold function for the local similarity spectrum.(4) Mute the reflection area.(5) Pick the local maximum and record the corresponding space coordinates.

Figure 6 .
Figure 6.(a) The synthetical regolith model, (b) Forward result A with offset of 0.16 m (c) Forward result B with offset of 0.32 m.

Figure 6 .
Figure 6.(a) The synthetical regolith model, (b) Forward result A with offset of 0.16 m (c) Forward result B with offset of 0.32 m.

Figure 7 .
Figure 7. Demonstration of dip filter results in two datasets with different offsets.

Figure 7 . 21 Figure 8 .
Figure 7. Demonstration of dip filter results in two datasets with different offsets.Remote Sens. 2019, 11, x FOR PEER REVIEW 11 of 21

Figure 8 .
Figure 8.(a) Local similarity spectrum in two filtered datasets (Figure 6), (b) diffraction section of (a), (c) the result of rock positioning

21 Figure 9 .
Figure 9.The comparison of rock positioning.

N
is the number of the detected rocks which are non-existent, all N is the total number of rocks.The detection rate of the above-mentioned forward result is = 92.105%det R , the missed detection rate is = 7.895% mis R , and the false alarm rate is = 68.421%fal R .It can be seen that our method has a high detection rate and a low missed detection rate.The reason for missed detection is that the rock is close to the reflector so that the diffractions are interfered with by reflections.The false alarm rate is relatively high; there are two main reasons for the excessive extraction of rocks: (1) In the rock enrichment area (9-13 m), diffraction interferences decrease the accuracy of local

Figure 9 .
Figure 9.The comparison of rock positioning.

Figure 10 .
Figure 10.The results of the dip filter for (a) LPR CH-2A data and (b) LPR CH-2B data.Figure 10.The results of the dip filter for (a) LPR CH-2A data and (b) LPR CH-2B data.

Figure 10 .
Figure 10.The results of the dip filter for (a) LPR CH-2A data and (b) LPR CH-2B data.Figure 10.The results of the dip filter for (a) LPR CH-2A data and (b) LPR CH-2B data.

Figure 11 .
Figure 11.(a) Local similarity spectrum for filtered LPR CH-2A and B, (b) diffraction section of (a).Figure 11.(a) Local similarity spectrum for filtered LPR CH-2A and B, (b) diffraction section of (a).

Figure 11 .
Figure 11.(a) Local similarity spectrum for filtered LPR CH-2A and B, (b) diffraction section of (a).Figure 11.(a) Local similarity spectrum for filtered LPR CH-2A and B, (b) diffraction section of (a).

Figure 12 .
Figure 12.The result of rock positioning for LPR data.The relative dielectric constant is set to 3.

Figure 13 .
Figure 13.The interface of regolith and base rock.The relative dielectric constant is set to 3.
Fa et al., Dong et al. and

Figure 12 .
Figure 12.The result of rock positioning for LPR data.The relative dielectric constant is set to 3.

21 Figure 12 .
Figure 12.The result of rock positioning for LPR data.The relative dielectric constant is set to 3.

Figure 13 .
Figure 13.The interface of regolith and base rock.The relative dielectric constant is set to 3.
Fa et al., Dong et al. and

Figure 13 .
Figure 13.The interface of regolith and base rock.The relative dielectric constant is set to 3.
of the position estimation is less than 10% (−9.62% to 7.36%), and the maximum error values are −0.87 and 0.67 m.In the same way, we estimate the position of the interface.When ε

Figure 14 .
Figure 14.Scatterplot of the rock number and location at each 5 m.

Figure 14 .
Figure 14.Scatterplot of the rock number and location at each 5 m.

21 Figure 15 .
Figure 15.Analysis between the number of rocks and depth.

Figure 15 .
Figure 15.Analysis between the number of rocks and depth.

Table 1 .
Parameter list for three types of dip filters.