Evaluation of Pipe Materials in Water System Networks Using the Theory of Advanced Multi-Criteria Analysis

: This study used a multi-criteria analysis to ﬁnd the optimal material for water pipes in water systems. This paper used FRISCO for calculating the criteria weights and ranking the considered types of pipes. Five different types are considered using 22 criteria. The considered criteria included economic, environmental, and pipe properties. The results showed that the FRISCO method could be used for decision-making in water systems.


Introduction
Modern cities have complex above-and below-ground infrastructure. Our drinking water, delivered by a network of underground pipes, is vital to public health and the economy. This underground infrastructure is often neglected [1]. According to the Environmental Protection Agency, 4000-5000 miles of pipes are replaced annually, and this number is expected to rise [2]. When water pipes are not taken care of, they do not function properly, and water is wasted [3]. Leaks, interruptions, and other problems in pipes throughout water distribution systems lead to water loss, also known as non-revenue water (NRW). The global annual NRW volume reached 126 billion cubic meters, and it reduces the quality of water services, the city's water supply, and water quality and increases energy use [4]. Eighty-three percentage of non-revenue water was caused by leaks in transmission mains and service connections [5]. For instance, between 2014 and 2020, water system transmission lost 41% of Glendale's potable water production [6] and 10-30% in the United States and the United Kingdom. Developing countries may reach 70%; in addition, 3-7% in the Netherlands [7], 45% in Turkey [8], 47% in rural Iran [9], 40% in Addis Ababa, Ethiopia [10], 54% in Gabon, 20% in Burkina Faso, 72% in Nigeria [11], and 57.2-58% in Skiathos, Greece [12]. The quality and the type of pipe material have a significant impact on it [13]. To reduce NRW due to leakage and pipe failure, water loss is reduced by replacing the pipes [13,14]. Material choice is one of the most difficult parts of designing and making structural elements. It is also important for success, cutting costs, and obtaining better results [15]. Leaky pipes include transmission, distribution, and service. Depending on where they occur, they have different flow rates, disrupting tendencies, and visibility [16]. There is a close relationship between choosing the pipe material in the water systems, whether they are extension systems for old projects or for new projects, and maintaining the quality, safety, sustainability, and costs of the water systems. In light of climate change and water scarcity, research on water loss in potable water systems during transport is essential. After the design is completed, it can be hard to choose the right materials because materials can have so many different properties [17], and inappropriate materials can cause the network of water to fail, and its competitiveness depends on its material selection [18]. In order to properly allocate resources, stakeholders are more concerned with understanding the causes of pipe failure [19].
Pipe material, design and installation, operating conditions, and quality affect pipe failure probability. Pipe deterioration increases breakage rates, reduces hydraulic capacity, affects water quality, and shortens service life [51]. Some of the most common ways for HDPE pipes to break are ductile overload, non-ductile or pinhole cracks, and oxidative degradation [52]; for example, leaks at CI pipe sleeve connections; HDPE tee cracks, connector cracks, and pipe cracks; PVC pipe cracks, pipe corrosion, and tee leaks [49]. Between 1998 and 2002, the average number of pipe breaks per 100 miles in the United Kingdom was 5 for HDPE, compared to 8 for DI, 12 for PVC, 26 for AC, and 32 for CI [53]. In a Dutch failure case study, maintenance and failure data from seven companies were used to figure out how likely it was that a pipe would break in the future. Pipes are classified based on how easily they break during installation (AC, PE and PVC, CI, and DI), how quickly they deteriorate internally (AC, CI, DI, and PE and PVC), how quickly they deteriorate externally (CI, AC, PE and PVC, DI), and how quickly they deteriorate during land traffic (CI, AC, PE and PVC, and DI) [54]. It is possible to make a solid case out of DI, PVC, or HDPE, as mentioned in [53]. For optimal seismic performance in Los Angeles, high-density polyethylene (HDPE) or DI with locking joints may be the best option. Given a repair rate of six repairs per kilometer, the number of times a water pipeline is fixed per kilometer is mentioned in [55]. The length of the pipe increases the odds of breakage. Reducing the pipe diameter increases the possibility of breakage [56]. Pipes are more likely to break when pressure rises [56,57]. In general, there is a high risk of damage with PVC pipes [56]. NRW losses were studied as a network. Pipe bursts, breaks, and leaks have been reported in 14 states (2013-2017: 2,262,798 complaints): AC, 27.1%; HDPE, 19%; uPVC, 14.3%; DI, 8%; CI, 0.5%; and others, 2.1%. HDPE pipes contribute more to NRW than DI pipes; the study focused on HDPE, mild steel, and DI pipes [13]. CI and AC pipes fail over time, but for different reasons. CI fails due to a common fault, and AC fails due to a circular fault [58]. To evaluate the 14 pipe failure studies, we compared them using numbers from 1 to 5, with 5 representing the pipe with the lowest risk of failure, followed by the numbers from 4 to 1, and finally the arithmetic mean. DI has the lowest failure rate (3.79), followed by HDPE (3.7), PVC (3.15), CI (2.7), and AC (2.43), based on the arithmetic mean of the failure rates for each material. 'Examining Success Probabilities for ground movement Section also lists earthquake failure criteria.

Repair and Replacement Costs
The cost of maintaining a piping system varies according to its material, age, maintenance frequency, and maintenance or reinstallation procedures. Certain materials require special equipment. Professional replacement or repair may increase the cost of maintenance. Pipes are arranged according to their lifespan, CI, AC, DI, HDPE, and PVC; according to their installation, HDPE and PVC are the same and lower than DI and CI [33]; according to the probability of failure, DI has the lowest failure rate followed by HDPE, PVC, CI, and AC.

Pipe Weight and Portability
The densities per meter of PVC, HDPE, and DI for a diameter of 200 mm are 17.26, 15.02, and 31.40 kg/m, respectively [38]. The weight saving over PVC/DI pipe is 13% [47]. Lightweight PVC pipe reduces transportation costs and affects the climate while also simplifying pipe handling on-site [35]. For a pipe with a diameter of 300 mm, PVC is 10, CI is 68, PE is 11.5 kg/m [59], and AC is 27.4 kg/m [60]. Water Supply System Reliability A piping system's reliability is its long-term ability to perform its intended function. Pipe material, age, and resistance to failure due to the impact of wear, corrosion resistance, temperatures, UV radiation, or aggressive chemicals can all have an impact on the reliability of a piping system. Together, these elements cause pipe failure.

Traffic Density and Road Conditions Affect Pipes
Failure of local water supply systems as a result of traffic leads to higher repair costs, excessive water losses, and limited destruction of other utility networks [61]. For example, the deformation and failure of HDPE pipes are influenced by factors, such as traffic loads [62]. The environmental impact of road construction exceeds that of transportation and installation combined [46]. Heavy vehicles driving over buried HDPE, PVC, and DI pipes were modeled using finite element analysis. These loads had minimal effects under many conditions, including corrosion [24].

Ease of Handling Emergency Situations
Time is of the essence, so a piping system that is easy to access and repair is crucial. The type of pipe material, ease of repair, whether the pipe is buried deep underground, accessibility, special tools and equipment, weight and brittleness, location, and accessibility can affect emergency response. Metal and asbestos pipes require more extensive repairs or replacements, while plastic pipes can be repaired with a coupling. HDPE and PVC pipes are lightweight and easy to move. CI, DI, and AC are heavy and difficult to handle.

Estimated Future Repair and Replacement Expenses
Pipes made of materials like PVC or HDPE may require more frequent maintenance and have a higher repair and replacement cost due to their lower durability, whereas pipes made of Lifespan DI and CI may require less frequent maintenance and have a lower repair and replacement cost due to their higher durability.

Material Corrosion Rate
Corrosion is one of the most significant factors affecting water quality and pipe corrosion. AC resists corrosion. It has health risks that limit installation. DI and CI can be corroded by aggressive water. There have been several reports of red and turbid water. PVC and HDPE are resistant to corrosion. Some pipe plasticizers contain lead, an emerging pollutant problem [63]. Similarly, rapid corrosion occurs in both CI and DI [1]. Leaching corrosion causes AC pipes to fail [64][65][66]. In an investigation into the reasons for the failure of cast iron and steel pipes, corrosion, transient pressure, and street loads were identified as the leading causes of failure for large-diameter pipes [22]. Iron release from CI pipes causes red water [67] Cast iron is affected both internally and externally by corrosion, which causes pipeline failure and fracture [68].

Environmental Impact
Different pipe materials can have very different effects on the environment, depending on the material and how it is made, installed, and thrown away [33]. This criterion is important because it makes it necessary to look at how the environment might change over the life of the pipe to figure out how it will affect the environment. The life cycle of PVC, HDPE, and DI pipes was analyzed to determine their carbon emissions in energy, pipe installation, use, and transportation. The percentage difference is as follows: 25%, 25%, and 26% for PVC, HDPE, and DI pipes, respectively [33]. DI and PVC pipes have the largest and lowest environmental impacts, respectively, compared to HDPE [29,69]. The 90-mm-diameter HDPE and PVC pipes have comparable environmental impacts, and by comparing DI to HDPE and PVC with a 200-mm diameter, DI has greater environmental impacts [47]. In comparison, the percentages were 12%, 11%, and 53% for HDPE, PVC, and DI, respectively [41].

Biofilms
Biofilm protects bacteria from chlorine and helps infected microbes grow. It can cause pipe corrosion, hydraulic issues, poor water quality, bad tastes and odors, and macroinvertebrate growth [70]. Biofilms are associated with water discoloration and foul odors. It contributes to the corrosion of both metallic and synthetic polymeric substances [71]. Researchers looked at how bacteria formed biofilms on PVC, HDPE, and stainless steel that had been exposed to ozone water. They found that, overall, biofilm buildup on different surfaces was pretty similar [72]. In a flow/non-flow biofilm study, HDPE and PVC growth rates were also similar [73]. For colonization and biofilm formation in model drinking water distribution systems, HDPE was superior to PVC [74]. During the stable period, ductile iron (DI) had greater biofilms than polyethylene (PE) [75]. Mycobacterial gene copies were significantly higher in DI pipes than in CI pipes, indicating the importance of material type in biofilm formation [76], and its effect is greater on AC than on PVC pipes [77]. PVC and HDPE have less biofilm resistance [78].

Cumulative Energy Demand (CED)
In this context, we will examine pipes from the perspective of their cumulative energy demand. Constant dimensions were taken into account in the comparison process. DI pipes are two to three times more energy-intensive than HDPE and PVC [46]. By adding the operation and construction phases, PVC uses the least amount of energy, followed by HDPE and DI [47]. The energy requirements for pipes in the manufacturing process from the extraction of raw materials to plant exit are 34.4, 25.5, 75.2, and 74.9 MJ/kg for DI, CI, PVC, and HDPE, respectively, and can be arranged as CI, DI, HDPE, and PVC [33]. DI pipes have less embodied energy than PVC or HDPE pipes [79,80]. PVC has the highest embodied energy, followed by HDPE and DI [38,44]. Pipe manufacturing was neglected [46]. AC pipe requires 20-40% less energy than DI or PVC [81]. PVC uses more energy and emits more CO 2 than non-recycled polyethylene, and vice versa if recycled [82]. The production phase accounts for 65% of the GWP and 67% of the cumulative energy demand [46]. When comparing the diameters of PVC, HDPE, and DI pipes, from smallest to largest, the greater diameter, the greater embodied energy, which was highest for DI, followed by HDPE, and lowest for PVC. In addition, PVC, which after 25 and 50 years, has the highest CED impact, followed by HDPE and DI [46].

Discoloration Water
Discolored tap water or turbidity/red water is a major cause of water quality complaints [83,84]. When talking about turbidity, the material of the pipe is very important, as can be seen in the case of iron pipes [85]. In a study where the pipes were arranged based on the quality of the water, the DI and CI pipe materials were ranked in the order of increasing turbidity and biofilm diversity as follows: CI and DI [86]. During the cleaning operations of water systems, there is a correlation in the concentrations of both iron and manganese [83].

Pressure Range
Researchers say water pipe rupture is related to the material and environment of the pipe, as well as the internal pressure load. Water hammers, which generate high water pressure, also cause pipe bursts. Broken pipes caused by high water pressure are a significant area of study [22,87]. PVC [23,88], ductile iron (DI) [89], cast iron (CI) [90], asbestos cement (AC) [91], and HDPE pipes deformation and failure under internal pressure must be studied and predicted to maximize their use [92].

Influence of Residual Chlorine
Chemical additives are needed to maintain the quality of water, but they can shorten pipe life. Desalinated water's chlorine decay was linked to wall decay, and high wall decay indicated deteriorated distribution pipes [84]. Residual chlorine in tap water accelerates the deterioration of plastic pipes [93]. Inactivating micro-pollutants with chlorine dioxide or sodium hypochlorite has long-term effects on the pipe material [94]. Disinfectants and biofilm affect iron corrosion's composition, structure, and morphology [95]. Tensile tests on chlorinated HDPE and PVC showed no changes. HDPE is more permeable to water than PVC due to being chlorinated [96]. Biofilms on CI had a different community composition than those on HDPE and PVC [97]. The likelihood of trihalomethane formation is highest in PVC pipes and then in PE pipes [98]. PVC has a lower chlorine effect than DI or CI [99]. Length of operation affects asbestos cement wall decay constants; PVC and polyethylene pipes have lower chlorine decay constants; CI pipes have higher chlorine decay constants [100]. Reactive (iron) and non-reactive (PVC) pipe walls decay [101]. Chlorine decay for PVC is less than DI; in CI pipes faster than PVC pipes [102]. Plastic is resistant to aggressive water [78].

Purchase Costs of Pipes
For pipe production, installation, and transportation phases of 12-inch diameter per km, some production and maintenance expenses are excluded. The equivalent cost for total GWP is $25/MT. For every metric ton of CO 2 , PVC costs $7950, DI costs $11,800, HDPE costs $5455, and CI costs $8820 [33]. HDPE was 5% cheaper and PVC was 10% cheaper than DI for 12-inch-diameter and smaller pipelines [53]. The buying prices for HDPE, PVC, DI, and CI pipes vary depending on the supplier, location, amount, size, maximum pressure, and diameter of the pipe. HDPE pipes cost $1-5 per foot, PVC pipes cost $1-20 per foot, DI pipes cost $20-30 per foot, and CI pipes cost between $20 and $40 per foot. The price for pipes of 200 mm diameter, for example, is as follows: asbestos $4.24/m, DI $16.40/m, CI $13/m [103], HDPE $0.21/m, and PVC $0.5/m [104]. The cost of manufacturing a pipe with a 12-inch diameter is as follows: HDPE $5.375/m, PVC $7.875/m, CI $8.725/m, and DI $11.7/m. Production costs are very high for DI, CI, PVC, and HDPE [33].

The Network Leakage Probability
Due to the complexity of the factors, predicting the rate at which water distribution network pipes will fail over time is important for setting aside enough funds for renewal [105]. A piping network's leakage risk depends on its material, quality, lifespan, condition, environmental conditions, and maintenance and repair practices. Pipe material and quality can affect leakage. Compared to DI or HDPE, AC, CI, and PVC are more likely to leak. Older or less-protected pipes may leak more than newer ones. Regular inspections, cleaning, and repairs can identify and fix potential leakage points before they worsen, while neglecting maintenance and repair can increase leakage over time.

Guaranteed Risk-Free Pipework
The non-profit National Sanitation Foundation (NSF) certifies products that meet quality and safety standards. They approve PVC [106], HDPE, and DI pipes for drinking water [23]. AWWA, ASTM, and the EPA do not classify CI as drinking water pipes. Because of corrosion and iron leaching, cast iron pipes are rarely used for potable water systems. Iron in drinking water is harmful. The secondary maximum contaminant level for iron in drinking water set by the EPA is 0.3 mg/L [107]. AC consumption increases the risk of developing stomach cancer [107,108]. Asbestos risk scores did not predict the occurrence of gastrointestinal tumors [109,110], but it causes lung cancer [111] and ovarian cancer in women [112].

Examining Success Probabilities for Ground Movement
Earthquake water main rupture probability: High vulnerability for CI 6, moderate for AC 12, low to moderate for PVC 13, low for DI 18, and low for PE 19, i.e., arranged as PE, DI, PVC, AC, and CI [113]. In terms of earthquake performance, PVC has historically fared poorly in comparison to DI and HDPE [53]. During the earthquake, pipes break all over the place (failure types are barrel, pulled joint, joint failure, and fitting). AC 1.79,  [114]. In a UK city, breaks in pipes, broken down by material, such as cast iron (45%), polyethene (22.3%), and asbestos cement (19%), of varying diameters (data from 1995-2018) are as follows: CI accounts for 69.3%, polyethene for 4.6%, and AC for 14.9% [56]. The length of the pipe increases the odds of breakage. Reducing the pipe diameter increases the possibility of breakage. Pipes are more likely to break when pressure rises [56]. In general, there is a high risk of damage with PVC pipes [56].

Additional Considerations
HDPE pipes are resistant to fatigue and water hammer, whereas PVC pipes are brittle and can leak quickly. HDPE is rubbery, whereas PVC is brittle like glass [115]. For HDPE, quantitative threshold odor number (TON) values ≥ 4. Migration tests of PVC pipes revealed few volatile migrants and no odor [21]. Socioeconomic factors affect pipe service life [19].
Based on the findings of a comprehensive literature review, a set of criteria and indicators are used. In order to maintain the quality, safety, sustainability, and costs of water systems, the literature review highlighted the significance of the decision-making process in selecting the pipe material in water systems, whether they are extension systems for old projects or modern systems. Many criteria for evaluating water pipes were discussed in the literature, either singly or collectively; however, in this study, these were compiled into 22 elements to make a comparison in the process of evaluating pipes in water systems using FRISCO's theory of multi-criteria analysis.

Materials and Methods
Advanced multi-criteria analysis can be used to compare various options by determining the possibilities, defining the criteria, measuring the criteria and their relative importance, and determining weighted and overall scores.

The following Criteria Have Been Selected
A set of criteria was developed based on the findings of a comprehensive literature review. These 22 criteria have been compiled to represent the most important aspects in selecting pipes by using the multi-criteria evaluation method.
The criteria selected are as follows: 1. Low cost of production; 2.
Low friction losses;
Repair and replacement costs; 6.
Water supply system reliability; 8.
Traffic density and road conditions affect pipes; 9.
Ease of handling emergency situations; 10. Estimated future repair and replacement expenses; 11. Probability of failure; 12

The Process of Determining Weights for Each Criterion
The FRISCO formula was used to rank the criteria and assign a weight factor for each criterion because it is universally acknowledged as the best and most used for this type of analysis [116][117][118][119][120][121][122][123][124].
The FRISCO formula was used to calculate the weighting coefficients: where p represents the sum of the points obtained for each line by the element taken into account; ∆p represents the difference between the point of the item taken into account and the point of the item from the last level; m represents the current number of criteria is outclassed (outperformed in terms of points) by the criteria considered; Ncrt represents the total number of criteria that have been taken into account; ∆p represents the difference between the point of the item taken into account and the point of the first level.
The criteria's weights on a three-value Latin square grid will be used to calculate the weighting factors (0, 0.5, and 1). As Ncrt is a representation of the number of criteria used in the study, Ncrt here is equal to 22. A comparison is made between each criterion in this grid, with the input in relation to weights (0, 0.5, 1) in each line, followed by the output in each column. That is when this criterion is parallel to the one in row [125].
For the insertion process in the Latin grid to calculate the weighting coefficients (γ i ), if the criteria are more important than the comparison criterion, the cell concerned takes the number 1, and if it is of the same importance, the cell takes the number 0.5 and at last the value is set to 0 when it is of the lower importance.
After setting the weights, they are summed for each line and called the points (p), which are equal to half the square of the number of criteria. In this study, the number of criteria is 22, and the half of the square of the criteria is equal to 242.0, which is also equal to the sum of the total points [125].
After determining the total points, the level of importance is determined by that the largest value of the specific grade points or the specified criterion represents the number 1, which is a more important criterion, and then the rest of the numbers come to 22, which represents the last criterion in the order in terms of importance.
When several criteria share the same level as found in this Latin grid, for instance in criteria No. 10 and No. 14, the average here represents the level, so 10 and 14 take the same number, which is 5.5 [125].
The role of the level is to determine the order in which the criteria are ranked from the point of view of the degree. The level value helps determine the correct value of the parameter (m). The value (m) corresponding to a criterion is equal to the number of terms (positive integer or zero) in the ascending sequence of levels, with values strictly higher than the level of the criterion considered.
In the table made with a square grid, the values in the levels column will be sorted (either up or down), and with 22 criteria, the order of levels going up is [1, 2, 3, 4, 5.5, 5.5, . . . ]. For example, for the criterion at level 1, m = 0; for the criterion at level 3, m = 19; and for the two criteria at level 5.5, m = 16 [125].
The role of the level is only to determine the order in which the criteria are ranked from the point of view of the degree.

A Contribution Note Is Added to One of the Criteria by Awarding an Ni Score
After figuring out the weighting coefficients, the variables will be analyzed by giving each option an Ni score based on the criteria or variables that were looked at. These scores show how important each criterion is. The scores are represented using the integer numbers from 1 to 10. The grade is given for each variable according to each criterion. That is, one variable is analyzed in turn in terms of each criterion, until all the variables are exhausted.

Calculation of Products between Ni Scores and Weighting Coefficients (Result Matrix)
The products among the Ni scores of the criteria for the five pipe alternatives and weighting factors will be calculated in a table called the result matrix. Then this operation will be summed and will primarily be the variable with the largest summation, and if the values of the summation are close, the variables involved guarantee close performance.

Results
The data presented in Table 1 display the process of determining the weights of each criterion, and it is also noted that the main diagonal of the quadratic table of criteria contains only 0.5 values because no criterion can be more or less important than it, and then each row is summed separately to obtain the sum of the points represented with the letter (p).
To calculate the weighting coefficients of the FRISCO formula as given in Table 2; for example, to determine ∆p, the difference between the element point taken into account in the calculation and the point of the last level element is calculated. Here, for example, the last item is criterion No. 16, which obtains 6.5 points and is compared to all the criteria from 1 to 22; in the same way to calculate (−∆p ) the difference between the point of the item taken and the first level, and here it is equal to criterion No. 12, which obtained 20 points.
The data presented in Table 3 show that the alternatives to pipes were analyzed by giving Ni scores for the criteria that were analyzed using the integers from 1 to 10. Criterion 12, which is a criterion that allocates environmental impacts, for example, says that HDPE has the least impact on the environment; so in terms of weight, the highest score is taken, and if the criteria are positive, the highest score will be given to the specific alternative. Table 4 presents the results of multiplying the weighting coefficients in the scores for the five alternatives to the pipes. The final score, which is used to rank the alternatives, is found by adding the results of multiplying each column. This is shown in the last line of the table. The analyses revealed that the alternative, as shown in Figure 1, HDPE, has the highest quantity (218.78), followed by PVC (218.66), AC (164.47), DI (164.25), and finally CI (140.09). There are numerous similarities between PVC and HDPE, and AC and DI. Table 1. This is a table showing the process for determining the weights for each criterion.   1  2  3  4  5  6  7  8  9  10  11  12  13  14  15  16  17  18  19  20  21

Discussion
Decision-making entails the identification and selection of alternatives in order to choose the most appropriate alternative based on the various considerations and expectations of the decision-makers. Every problem-solving decision is based on information determined by the priorities of the decision-makers. This study focused on the analysis of

Discussion
Decision-making entails the identification and selection of alternatives in order to choose the most appropriate alternative based on the various considerations and expectations of the decision-makers. Every problem-solving decision is based on information determined by the priorities of the decision-makers. This study focused on the analysis of multiple alternatives based on the theory of advanced multi-criteria analysis, including information, alternatives, values, and preferences, in order to select the best pipes for water systems.
In order to preserve water resources as a result of leakage caused by exploding pipes and maintenance and replacement operations, it is crucial to make the right decision when selecting the type of pipe material to be used from the market's available options. This study concluded with the assistance of stakeholders in the decision-making process based on evidence and facts in the installation and replacement of water system pipes by comparing the most commonly used materials in this field.
The 22 standards were developed on the basis of the literature and actual pipe problems encountered during the operational lifetime.
The weights were determined based on the opinions of water pipeline operation, maintenance, and planning specialists. The Ni scores were established based on an exhaustive review of the literature. These standards have been developed as a result of an in-depth analysis of pipe problems from the beginning of production to the end of their service life, as well as the factors that affect them, so that can evaluate alternatives.
Several specialized units in the field of water operation and maintenance have discussed the importance levels of water systems, but the evaluation process heavily depends on the institution's priorities when determining its standards and weights.
The results of the Environmental Impact Assessment are one of the most important factors taken into account throughout the life of the pipes. After environmental impact and guaranteed risk-free piping work, the highest initial weights were assigned to criteria that have an impact on maintenance and operation, such as reliability, probability of failure, repairability, and service life, as presented in Figures 2-4. About 41% of global warming and 44% of energy consumption come from water system operation and maintenance [46]. Pumping emits 90% of greenhouse gases and uses 60% of energy [57]. The annual energy consumption was 220-260 kWh per person [126].
According to the sources [38,44], PVC meets the cumulative energy demand criterion with the highest value. PVC and high-density polyethylene yield comparable end-products, so they converge. Despite cumulative energy demand (criterion 13) increasing from 9 to 10 for PVC pipes, HDPE pipes maintained their lead in terms of the final score. According to the established criteria, the HDPE alternative came in first, followed by PVC, asbestos cement, ductile iron, and cast iron.
Several specialized units in the field of water operation and maintenance have discussed the importance levels of water systems, but the evaluation process heavily depends on the institution's priorities when determining its standards and weights.
The results of the Environmental Impact Assessment are one of the most important factors taken into account throughout the life of the pipes. After environmental impact and guaranteed risk-free piping work, the highest initial weights were assigned to criteria that have an impact on maintenance and operation, such as reliability, probability of failure, repairability, and service life, as presented in Figures 2-4. About 41% of global warming and 44% of energy consumption come from water system operation and maintenance [46]. Pumping emits 90% of greenhouse gases and uses 60% of energy [57] . The annual energy consumption was 220-260 kWh per person [126].      Conducting weights may vary according to the policies of the institution, and it is a very complex process, but the priorities as shown in the percentage of weights can be adopted in accordance with the institution's requirements. Taking current environmental commitments and climate changes during the pipes' operational lives into account, the resulting weights were reasonable. The percentages ranged in eight levels, from 16% for environmental impact to 1% for ground movement and pressure level as presented in Figure 5.
The water supply may be harmful due to an asbestos pipe [66]. For ease of connection during maintenance, it can be used again to repair the same network if a pipe fails. Therefore, it was necessary to refer to it in the future replacement process, and a new criterion of comparison could be set in the case of connecting the old asbestos pipes with a new system of pipes to replace them according to the ease of connection with the asbestos line. Sometimes pipe replacement costs matter. Due to the high cost of replacing old pipes with new recommended pipes, asbestos is sometimes used in new water systems' networks, especially in long asbestos networks.  According to the sources [38,44], PVC meets the cumulative energy demand criterion with the highest value. PVC and high-density polyethylene yield comparable end-products, so they converge. Despite cumulative energy demand (criterion 13) increasing from 9 to 10 for PVC pipes, HDPE pipes maintained their lead in terms of the final score. According to the established criteria, the HDPE alternative came in first, followed by PVC, asbestos cement, ductile iron, and cast iron.
Conducting weights may vary according to the policies of the institution, and it is a very complex process, but the priorities as shown in the percentage of weights can be adopted in accordance with the institution's requirements. Taking current environmental commitments and climate changes during the pipes' operational lives into account, the resulting weights were reasonable. The percentages ranged in eight levels, from 16% for environmental impact to 1% for ground movement and pressure level as presented in Figure 5.   Inaccurate data in an environmental impact can have a significant impact on the results. PVC has the highest CED effect after 25 and 50 years, followed by HDPE and DI [46]. Despite this change, HDPE remains in the first place in the final score, followed by PVC and DI.
As for the effect of pipe diameters on the selection process, the initial evaluation can be based on the environmental impact, i.e., the diameter of the pipe is selected based on the environmental impact. Then other criteria related to the specified diameter are compared as in [33], which demonstrated that PVC 410-510 mm, HDPE 410-460 mm, DI 460-510 mm, and CI 460-560 mm have the lowest economic costs and global warming potential [47]. Because pipe diameter is related to environmental impact and cost, it has a substantial impact on the evaluation process used to determine the final score. In addition, pipe diameter has a substantial impact on the weights process.
According to the available literature, the most frequently utilized pipes in water distribution systems were selected for this evaluation. The importance of comparison criteria, used materials, and weight has been extensively discussed with specialists, and given the focus of recent research, it is more logical.
Although embodied energy is an element of the environmental impact assessment, the single and combined comparisons were chosen. Water system sustainability can be better understood, and decisions can be made by taking into account both embodied energy and environmental impact but being aware of its function and design and able to offer suggestions for its enhancement, while making sure no essential elements of sustainability are missed. Despite its low energy consumption, a product may have a significant negative effect on the environment. The overall sustainability of the piping system can be improved by considering both criteria and addressing the trade-offs that arise from doing so.
Pipes' expected lifetime was calculated using an average of findings from other studies; this could provide a more accurate picture once the rate of pipe failure during service was factored in.
Future research may include a consideration of the effect of environmental factors on the pipes as a criterion for evaluation. The severity of pipe defects changes with the seasons, as shown in [127,128], socioeconomic factors and soil quality [19], and mechanical properties of materials [129], including ultimate tensile strength, percent of elongation, hardness, and yield strength [15].
Due to a lack of information in the literature, the following elements have not been compared: fatigue, water hammering, elasticity, and fragility. However, they may be included in future studies comparing pipes based on their tolerance of operational conditions, such as fatigue, water hammering, elasticity, fragility [115], number of threshold odors (TON) [21], and UV radiation. In addition to the dimensions and operating conditions such as pressure and temperature, the temperature influences the yield stress diagram. Therefore, we recommend that temperature should be taken into account during the evaluation process, as it affects differently and may increase the likelihood of pipe failure [128]. Therefore, other criteria can be developed based on the degree to which temperature influences the pipes.
It is preferable to have input from other specialists when determining comparison criteria and assigning relative importance levels.