Assessment of Stormwater Quality in the Context of Trafﬁc Congestion: A Case Study in Egypt

: The aim of this study was to investigate the effect of trafﬁc congestion in urbanized areas (parking lots and highways) on stormwater quality. Three separate locations in Egypt’s heavily urbanized and populous Giza Governorate were picked for the purpose of monitoring and evaluating the stormwater quality: Faisal (A), El Dokki (B)


Introduction
The disparity between water demand and availability in Egypt is widening due to the country's limited water resources, fast population increase, and climate change [1,2].Egypt is awaiting the advent of a hazardous situation: a complete absence of water security, as the rest of the world battles resource shortages.From the expansive banks of Upper Egypt to the congested, populated Delta, the Nile has supported growth and development for millennia; civilization in the area was not merely a supplement of water but a direct outcome of it [3].The Nile is frequently depicted in literature and art, and it may even be heard in Egypt's national anthems.Egypt has frequently been referred to as "the gift of the Nile".However, Egypt's population of over 102 million is currently in danger from both natural and man-made droughts [4].Egypt has been battling an annual water deficit of almost 7 km 3 for the past few years; according to UNICEF (2021) [5] by 2025, the nation would "run out of water" completely.
There is an urgent need to talk about the issue in practical rather than fatalistic terms due to tensions in the south; the quickly rising, contentious Renaissance Dam in Ethiopia; Egypt's arid environment; and the overwhelming realities of climate change [6].Over the past few years, Egypt has struggled with an annual water deficit of almost 7 km 3 ; by 2025, the nation would "run out of water" completely [7].According to the Falkenmark Index [8], the nation was already functioning below the level of water scarcity; the total renewable water resource per person was 628 m 3 /year, a quantity that is currently under tremendous strain due to a growing population that has been expanding at a rate of over 1.8 to 2.1% annually since 1989 [1].Therefore, to address this issue, Egypt should think about using natural and unconventional water resources, such as deep groundwater extraction, seawater desalination, and wastewater treatment [9][10][11][12].One alternative is rain harvesting.During specific storm events, large amounts of rain fell in various parts of Egypt, which can occasionally cause disasters like flash floods and inundations.Rainwater harvesting is seen as a viable and promising solution to the problems of water scarcity and inundation [13,14].Stormwater gathers significant quantities of pollutants from point and non-point sources when it flies over sidewalks, lawns, driveways, roads, and other urban surfaces.However, the quality of stormwater effluents is typically subpar when compared to natural waterways or even treated municipal sanitary wastewater [15][16][17].Global urbanization is constantly sealing soils, removing vegetation, and altering natural drainage systems.These changes result in the surrounding landscape's infiltration capacity decreasing, which causes an increase in the frequency and speed (such as the immediacy of a flooding event) of stormwater runoff events [18].For instance, road surfaces in urban areas can contribute up to 40% of the overall amount of heavy metal loads and up to 26% of the total runoff volume [19][20][21].This is an excessively high contribution to the pollution load when you consider the space taken up by road surfaces [22,23].The main sources of traffic-related pollutants are engine oil leaks, tire and brake wear, road surface abrasion, and exhaust emissions.These contaminants can take the form of airborne particulate matter, heavy metals, solids, and polycyclic aromatic hydrocarbons (PAHs) [24].Road surface solids are diverse in composition.In addition to traffic-related activities, air deposition [25] and nearby soil [26] also contribute solids to the environment around urban roads.During transport, complicated mixing mechanisms are used for solids that are deposited on road surfaces.Additionally, because of the regular traffic operations, traffic-related particles frequently react with the mineral components of soil to create special combinations.A lot of research has been carried out on heavy metals because of their potential damage to human health.The urban environment contains a variety of heavy metal species, but copper (Cu), cadmium (Cd), nickel (Ni), lead (Pb), zinc (Zn), and chromium (Cr) have drawn the most attention because their potential acute or chronic harmful effects on flora, fauna, and people.Table 1 summarizes heavy metals caused by traffic activities [27,28].Stormwater-associated toxic heavy metals can build up in rivers and have a negative effect on living things.The presence of heavy metals in stormwater can pose a risk to human health, substantially weakening the safety of reuse at a time when stormwater is garnering significant attention as a potential alternative water supply [29].The type of vehicle and operating circumstances have a significant impact on the amount of airborne particle pollution produced by that vehicle [30,31].As fuel usage, which, in turn, depends on vehicle speed, affects emissions, operating circumstances play a big part.Traffic jams can result in frequent vehicle stop-starting, which results in incomplete fuel combustion and significant pollution loads such as particles.This implies that the production of airborne particulate pollution will be influenced by traffic congestion [32].
Polycyclic aromatic hydrocarbons (PAHs) are a broad class of chemical molecules containing at least two fused benzene rings arranged in various ways [33].The main source of PAHs on urban road surfaces is traffic.Vehicle exhaust and the abrasion of road surfaces are the two main traffic-related sources of PAHs.As a result, increased traffic volumes can be blamed for higher PAH loadings [34].Both the species composition and PAH loadings are impacted by traffic factors.Heavy PAH species offer a high risk to ecosystems and have a detrimental impact on the security of stormwater reuse.Vehicles' use of fossil fuels causes the release of particle pollution into the atmosphere.Although initially suspended in the atmosphere, these pollutants can be deposited on ground surfaces through dry and wet deposition processes, where they can, then, be carried to receiving waterways by storms.Therefore, the periodic monitoring and assessment of the quality of stormwater, groundwater, and surface water for different uses is an important issue for water resources management [35,36].
The water quality index (WQI) model is a useful tool for evaluating the quality of surface water [37,38].It makes use of aggregation techniques to reduce vast amounts of data on water quality to a single value or index.The WQI model has been used internationally to assess water quality (surface water and groundwater) using regional water quality standards.Due to its standardized structure and simplicity of usage, it has gained popularity since its invention in the 1960s.The selection of the water quality parameters, the creation of sub-indices for each parameter, the computation of parameter-weighting values, and the aggregation of sub-indices to produce the overall water quality index are the four phases that WQI models typically follow, in that order.To assess the water quality of rivers, lakes, reservoirs, and estuaries, several researchers have used a variety of WQI model applications [39].Traffic condition is one of the primary issues affecting Egyptian society.Nowadays, it is difficult for people to use public transport because it is constantly congested, especially during rush hours.For the people, getting where they are going and estimating how long it will take them to get there is difficult.There could be additional issues and delays for the individuals at work [40].Therefore, traffic congestion contributes to the polluting of air and road surfaces, as stated in Table 1.The aim of this study is to focus on an insightful picture on stormwater quality for different uses in the context of traffic congestion.To accomplish this, (i) the earlier research on the effect of high traffic volume on stormwater quality is reviewed; (ii) a case study for the assessment of stormwater quality in Egypt is considered, where three urban catchments with varying traffic intensities in the Faisal-A, Dokki-B, and Hadayek El-Ahram-C regions were examined; (iii) for the year 2021, the monthly average daily traffic (MADT) data were collected and analyzed for the three urban catchments studied; (iv) a laboratory analysis (physical, chemical, and biological) was carried out for the collected stormwater in six samples during the winter season for each region, distributed as follows: Faisal-A (13 March and 12 December 2021), El Dokki-B (two samples) (14 March and 20 January 2021), and Hadayek El-Ahram-C (3 January and 5 February 2021); and (v) the stormwater quality is assessed using the water quality index (WQI) in comparison to the Egyptian water quality criteria [41,42] and the World Health Organization [43].In addition, the stormwater quality indices for irrigation including the sodium adsorption ratio (SAR), total dissolved solids (TDS), total hardness (TH), permeability index (PI), soluble sodium percentage (SSP), residual sodium bicarbonate (RSBC), magnesium adsorption ratio (MAR), and Kelley's ratio (KR) were applied, and, finally, (vi) the conclusions and recommendations were presented.

Study Area
The study area is located in the Giza Governorate in the northern part of the Nile River Valley in Egypt as shown in Figure 1   Moreover, Faisal Street is located in the east of Giza Governorate and extends to the western side of it at a distance of seven kilometers.Faisal Street is considered one of the most important entrances to Giza Governorate from and to many other governorates, at the end of which there is the shooting range that connects Giza Governorate and the roads leading to the governorates of Fayoum, Alexandria, and the North Coast.
The study area expresses a semi-arid climate [44].Weather data concerning the studied regions were obtained from the Egyptian Meteorological Authority (MEA) (http://web.civilaviation.gov.eg/companies/meteorology)(accessed on November, December, January, February, and March 2021).Figure 2 shows the average monthly rainfall depth and temperatures for the study area for the year 2021.

Traffic Data in the Study Area
The monthly average daily traffic (MADT) statistics for the studied road were gathered from the General Authority of Roads, Bridges, and Land Transport (GARBLT) (http://www.garblt.gov.eg,accessed on 3 June 2023) based on the Unicorn Limited device.The average MADT for Faisal Street, Dokki region, and Hadayek El-Ahram region were 47,950, 20,919, and 27,064 cars per day, respectively.The Arc GIS program was utilized to define the catchment area's size and uses for each type of surface: Housing area/Commercial area/Housing area/Restaurant and parking service/etc.(Figure 1).In addition, Table 2 summarizes the catchment area for the three studied regions (Faisal, Dokki, and Hadayek El-Ahram regions), the type of surface, and the MADT.

Points of Measurement
The The following distribution was made using the stormwater samples that were taken from each route throughout the winter season for this study: according to APHA [45], two samples, A1 and A2, from Faisal Street were sampled on 13 March and 20 December 2021, respectively; two samples, B1 and B2, from the El Dokki region were sampled on 14 March and 20 January 2021; and two samples, C1 and C2, from the Hadayek El-Ahram region were sampled on 3 January and 5 February 2021, respectively.The stormwater sample

Traffic Data in the Study Area
The monthly average daily traffic (MADT) statistics for the studied road were gathered from the General Authority of Roads, Bridges, and Land Transport (GARBLT) (http://www.garblt.gov.eg,accessed on 3 June 2023) based on the Unicorn Limited device.The average MADT for Faisal Street, Dokki region, and Hadayek El-Ahram region were 47,950, 20,919, and 27,064 cars per day, respectively.The Arc GIS program was utilized to define the catchment area's size and uses for each type of surface: Housing area/Commercial area/Housing area/Restaurant and parking service/etc.(Figure 1).In addition, Table 2 summarizes the catchment area for the three studied regions (Faisal, Dokki, and Hadayek El-Ahram regions), the type of surface, and the MADT.
Table 2. Description of the measurement points, catchment area, type of surface, and monthly average daily traffic (MADT).

Points of Measurement
The Catchment Area's Size (m

Stormwater-Monitoring Points and the Analyzed Water Quality Parameters
The following distribution was made using the stormwater samples that were taken from each route throughout the winter season for this study: according to APHA [45], two samples, A1 and A2, from Faisal Street were sampled on 13 March and 20 December 2021, respectively; two samples, B1 and B2, from the El Dokki region were sampled on 14 March and 20 January 2021; and two samples, C1 and C2, from the Hadayek El-Ahram region were sampled on 3 January and 5 February 2021, respectively.The stormwater sample points' locations are shown in Figure 3.The samples of stormwater were obtained in a one-liter high-density polyethylene bottle, pre-cleaned with 10% nitric acid, rinsed repeatedly with bi-distilled water, stabilized with ultrapure nitric acid (0.5% HNO3), and stored at a temperature of around 4 °C.These samples were brought to the Faculty of Agriculture's lab at Mansoura University where they underwent physical, chemical, and biological analysis.The water samples were analyzed for physicochemical characteristics: water temperature, electrical conductivity (EC), and total dissolved solids (TDS).The chemical parameters are pH, total hardness (TH), chemical oxygen demand (COD), biochemical oxygen demand (BOD), total nitrogen (TN), total suspended solids (TSS), Na + , Ca 2+ , K + , and Mg 2+ (major cations), and HCO , CO3 2− , Cl , NO , and SO4 2-(major anions).Inductively coupled plasma was used for the determination of the heavy metals Al, Cr, Cd, Fe, Cu, Mn, Ni, Zn, and Pb; and major cations Na + , Ca 2+ , K + , and Mg 2+ , according to ASTM D8110-17 (Model: ICAP 7400).In addition, the pH was directly measured during water sampling using a digital pH meter, Jenway pH-meter (location: U.K) Model: 3505.The hydraulic conductivity of the water was directly measured using the Hanna Combo meter, Model-HI 98129.
According to ASTM D1252-06 criteria, the chemical oxygen demand (COD) was determined.To determine TDS, a typical fiberglass filter was used to filter a known volume of thoroughly mixed sample material.In accordance with ASTM D5907-18, the filtrated sample (liquid phase) was then evaporated to constant weight at 180 °C.Total phosphorus was measured as orthophosphate by the ascorbic acid method according to UV/VIS Spec- The samples of stormwater were obtained in a one-liter high-density polyethylene bottle, pre-cleaned with 10% nitric acid, rinsed repeatedly with bi-distilled water, stabilized with ultrapure nitric acid (0.5% HNO 3 ), and stored at a temperature of around 4 • C.These samples were brought to the Faculty of Agriculture's lab at Mansoura University where they underwent physical, chemical, and biological analysis.The water samples were analyzed for physicochemical characteristics: water temperature, electrical conductivity (EC), and total dissolved solids (TDS).The chemical parameters are pH, total hardness (TH), chemical oxygen demand (COD), biochemical oxygen demand (BOD), total nitrogen (TN), total suspended solids (TSS), Na + , Ca 2+ , K + , and Mg 2+ (major cations), and HCO − 3 , CO 3 2− , Cl − , NO − 3 , and SO 4 2− (major anions).Inductively coupled plasma was used for the determination of the heavy metals Al, Cr, Cd, Fe, Cu, Mn, Ni, Zn, and Pb; and major cations Na + , Ca 2+ , K + , and Mg 2+ , according to ASTM D8110-17 (Model: ICAP 7400).In addition, the pH was directly measured during water sampling using a digital pH meter, Jenway pH-meter (location: U.K) Model: 3505.The hydraulic conductivity of the water was directly measured using the Hanna Combo meter, Model-HI 98129.
According to ASTM D1252-06 criteria, the chemical oxygen demand (COD) was determined.To determine TDS, a typical fiberglass filter was used to filter a known volume of thoroughly mixed sample material.In accordance with ASTM D5907-18, the filtrated sample (liquid phase) was then evaporated to constant weight at 180 • C. Total phosphorus was measured as orthophosphate by the ascorbic acid method according to UV/VIS Spectrophotometer/PG instruments Model: T80.The process relies on the formation of an antimonyl-phosphomolybdate complex by the interaction of potassium antimony tartrate and ammonium molybdate with orthophosphate in the presence of ascorbic acid as a reducing agent.This compound yields an intense blue color, which was measured spectrophotometrically at 885 nm using a 1 cm cell length.

Water Quality Index (WQI)
The water quality index is a method for determining how acceptable the water is for drinking and other uses [35] using one figure.The following is how the WQI values arrived at the 27 water parameters for physical, chemical, and biological characteristics.A weight of wi = 3 to 4 is assigned to contaminants that have a significant impact on water quality, whereas a weight of wi = 1 to 2 is assigned to contaminants that have little or no impact [35,38,39].Thus, weight = 2 is given to the following water parameters: pH, EC, SO 4 , CO 3 , HCO 3 , Cl, Mg, Ca, Na, and K.However, the weight attributed to TDS, TSS, TN, TP, Ni, Fe, Cu, and Al is 3, While the weights for NO 3 , NH 4 , BOD, and COD are set at 4. Additionally, the weights for Cr, Cd, Mn, Zn, and Pb are 4.
The following equation is used to determine the relative weight (Wi): wi is the weight of each parameter, where n is the number of parameters and Wi is the relative weight of the ith parameter.The quality-rating scale (q) is then established for each parameter using the following formula: where Ci is the concentration of each chemical parameter in each water sample in mg/L except for pH, and Si is the corresponding value according to [38].Then, the sub-index (SI i ) is estimated with each parameter, dimensionless and WQI, as follows: Then, WQI is determined as follows: where n is the number of parameters, q i is the quantity rating based on the concentration of the ith parameter, and SI i is the sub-index of the parameter.The relative weights (Wi) of the examined stormwater physicochemical characteristics are listed in Table 3.  Wi is the relative weight of the ith parameter, and wi, is the weight of each parameter.
The calculated WQI values can be grouped into six categories as shown in Table 4 [37].The Excel program was utilized to carry out the statistics analysis, correlation between water quality parameters, and computation of the different water quality indices.

Evaluation of the Suitability of Irrigation Water Quality
Sodium adsorption ratio (SAR), total hardness (TH), total dissolved solids (TDS), soluble sodium percentage (SSP), residual sodium bicarbonate (RSBC), permeability index (PI), magnesium adsorption ratio (MAR), and Kelley's ratio (KR) are the categories of groundwater indices that are used to determine whether or not a body of water is suitable for irrigation.Equations ( 5) to (11) were used to determine the following values: SAR, TH, SSP, PI, RSBC, MAR, and KR as shown in Table 5.Based on the classifications of the indices SAR, EC, TDS, RSBC, TH, SSP, KR, and MAR, Table 6 shows the suitability of stormwater for irrigation.

Stormwater Water Quality
Table 7 summarizes the statistical analysis for the measured stormwater quality parameters in light of WHO and Egyptian water quality standards.The results show that the pH and conductivity are in the range of common values for road runoff according to the Egypt Decrees [41] limits.With regard to phosphorus, this study discovered a relationship between traffic volume and stormwater pollution levels.Site A1 recorded the highest amounts of total phosphorus, followed by site C1.The highest amount of heavy traffic and the impacts of first-flush stormwater may increase oil pollution, which would explain the high pollution at site A with almost all of the traffic being heavy.On the other hand, the TSS are in the range of common values for road runoff; moreover, the total nitrogen and TDS are in the range of common values according to the Egypt Decrees limits, but site A1 has a higher value of TSS (817 mg/L).Figure 4A shows the variation of MADT for the studied sites and the pH indicating acid stormwater at El Dokki-B2, Hadayek E.-C1, and Hadayek E.-C2. Figure 4B shows the variation of MADT for the studied sites and the EC indicating low EC values for the stormwater at the smallest MADT at El Dokki-B1 and El Dokki-B2.On the other hand, the variation of MADT has no effect on the HCO 3 , Cl, NH 4 , and TN concentrations as shown in Figure 4C-E,I, respectively.In addition, the variation of BOD, COD, and TP concentrations with the MADT for the studied sites show a small variation as these pollutants come from point pollutant sources and do not depend on traffic congestion as shown in Figure 4K,L,J, respectively.Figure 4G shows significant correlations between MADT and heavy metals.The results indicated that the concentration of the TSS in stormwater is influenced by the traffic intensity where sites A and C show significantly higher pollution of TSS, because the traffic intensity at A is more than twice that of B and C. Most of the highest monthly loads were measured at the three sites, which have a MADT of 47,950, 20,919, and 27,064 cars, respectively.Modern engine lubricants prepared with zinc dialkyl-dithio phosphate compounds are employed to protect moving metal components from wear when considering phosphorus emissions from automobiles [54].The results also revealed that BOD concentrations were highest at C1, C2, A1, and A2 (45, 45, 40, and 38 mg/L, respectively), but, at site B, they were in the range of common values, according to the Egypt Decrees limits, and the COD was higher at site A1, A2, and C1 (80, 79, and 59.66 mg/L), respectively, but, at site B1, B2, and C2, it was in the range of common values.The levels of pollutant concentrations generated from the highest-traffic sites, such as BOD and COD and oil and grease, were relatively higher than those measured at lower-traffic sites.The results for heavy metals in Table 7 showed that the concentration of dissolved Zn, Cu, Fe, and Cr at El Dokki, Hadayek El-Ahram, and Faisal did not fall within the range of common values, in general, but the results for heavy metal concentrations were generally higher; this might be due to the high-traffic activities and percent of street areas in urban catchments (Figure 4).On the other hand, according to Egypt's Decrees limits, the value of Mn in all sites falls within the range of the common values for road runoff.Several studies on street runoff in the literature have found that metal concentrations are positively correlated with the number of vehicles on the street during a rainfall event [21].In addition, according to the findings, the concentration of the key heavy elements Al, Cr, Cd, Fe, Cu, Mn, Ni, Zn, and Pb is higher than the Egyptian stormwater standards, as shown in Figure 5.

WQI Results
Table 8 summarizes the WQI results for the studied regions.Therefore, the results show that the WQI ranged from 426 to 929 with an average of 661 + 168.The WQI of 776 and 708 for Faisal (A), 499 and 426 for El Dokki (B), and 929 and 626 for Hadayek El-Ahram (C) indicate that the water is unfit for drinking and, before use, proper treatment is required.Therefore, heavy metals like Al, Cr, Cd, Fe, and Cu were present in it.In addition, BOD, COD, and TP pollutants also contribute to the high value of the WQI. Figure 4 shows the relationship between the measured stormwater quality parameters, Egyptian water quality criteria (Egypt Decree [41,42]), and the MADT.(G) (H)

WQI Results
Table 8 summarizes the WQI results for the studied regions.Therefore, the results show that the WQI ranged from 426 to 929 with an average of 661 + 168.The WQI of 776 and 708 for Faisal (A), 499 and 426 for El Dokki (B), and 929 and 626 for Hadayek El-Ahram (C) indicate that the water is unfit for drinking and, before use, proper treatment is required.Therefore, heavy metals like Al, Cr, Cd, Fe, and Cu were present in it.In addition, BOD, COD, and TP pollutants also contribute to the high value of the WQI. Figure 4 shows the relationship between the measured stormwater quality parameters, Egyptian water quality criteria (Egypt Decree [41,42]), and the MADT.

Stormwater Quality for Irrigation
The results for the gathered samples' stormwater irrigation indices are summarized in Table 9.While the total hardness (TH) and residual sodium bicarbonate (RSBC) indicate poor irrigation water quality, the stormwater quality irrigation indices for TDS, SAR, SSP, PI, and MAR indicate excellent stormwater for irrigation.

Stormwater Quality for Irrigation
The results for the gathered samples' stormwater irrigation indices are summarized in Table 9.While the total hardness (TH) and residual sodium bicarbonate (RSBC) indicate poor irrigation water quality, the stormwater quality irrigation indices for TDS, SAR, SSP, PI, and MAR indicate excellent stormwater for irrigation.

Discussion
The generation of pollutants is affected by various factors, such as rainfall intensity, land type, and the previous dry period; their relationships have been well-established in previous studies [55,56].Based on the stormwater quality parameter results, the values of total phosphorus demonstrate remarkable fluctuations at most sites.Spatial variation was recorded, with site C1 showing the highest mean value (6 mg/L), followed by sites A1 and B1 (5.02 mg/L and 4.55 mg/L, respectively).The higher concentrations may be due to the domestic and industrial sewage disposal at these sites; moreover, the elevated phosphorous concentrations are related to the pollutants [11,57].It is interesting that the mean average value of TN is even lower than the recommended TN content according to the Egypt Decrees [41,42] and WHO [43].In addition, heavy traffic and other human activities that produce air pollutants such as ozone, carbon dioxide, hydrocarbons, sulphur oxides, and suspended particulate matter contribute to a decrease in pH, indicating acid stormwater (Figure 4A).The results show that traffic intensity has an effect on the TSS in stormwater.Table 7 and Figure 4G shows the substantially higher pollution of TSS at the Faisal site compared to that at El Dokki and Hadayek El-Ahram, where the traffic intensity at Faisal is more than twice that of El Dokki and Hadayek El-Ahram.These results are consistent with the previous literature [58,59].Table 7 and Figure 5C,D,H show that the average concentration of dissolved Zn, Cu, Mg, and Fe was 3.91 mg/L, 1.82 mg/L, 46.25 mg/L, and 7.62 mg/L, respectively, at the Faisal-A1; whereas, it indicates 3.028 mg/L, 2 mg/L, 500 mg/L, and 7.21 mg/L, respectively, at El Dokki-B1.At Hadayek E.-C1, it was 3.342, 1.253, 46.249, and 6.23 mg/L, respectively.In general, the results of heavy metal concentrations were generally higher due to the high-traffic activities and percentage of street areas in urban catchments [29].For example, in several studies, including those by [60], it was shown that the primary factor influencing the concentrations of heavy metals in stormwater was traffic density.Heavy metal pollutants from vehicles may also be affected by driving behaviors (such as how often brakes are used) and how long vehicles are left in a location (idling).It is well-recognized that significant sources of metals in stormwater include tire wear and vehicle brake emissions [28].The results showed that the levels of organic pollutants (COD and BOD) and disintegrated heavy metals (Zn, Cu, Pb, and Mn) were mainly due to the high traffic volume; these results are compatible with the previous literature [59].The assessment of drinking water quality is a timely requirement amid emerging public health problems in this context, where the availability of safe water is at risk due to natural and man-made activities; the WQI was employed to analyze the variation in stormwater quality.For the six stormwater samples from Faisal-A1-A2, El Dokki-B1-B2, and Hadayek E.-C1-C2, using the Excel program, the correlation matrix between the researched physio-chemical parameters and WQI was performed and examined as shown in Table 10.As a result, it was shown that there was a high positive correlation between WQI and SO 4 , Cl, BOD, TSS, Cr, Cd, and TDS, while a moderate correlation was found between WQI and COD, Zn, and Al.The correlation between QWI and Mg, on the other hand, is strongly negative, while the correlation between QWI and Na, K, and Al is modest.Weak correlations are observed between WQI and pH, HCO 3 , Cu, Mn, and Ca.As shown in Table 10, an 84% positive correlation between TSS and WQI is observed where the TSS may include heavy metals that are transferred from the surface by stormwater during the rainfall season.Therefore, lowering the amount of TSS in stormwater would lead to significantly reduced levels of particle-bound heavy metals and total phosphorus.There are other options, such as eliminating particle-bound pollution using non-structural preventive approaches, such as street sweeping, before it enters storm drain water.To collect rainwater, it is also recommended to have an effective stormwater sewerage system.The irrigation water quality indices show the total hardness (TH) and residual sodium bicarbonate (RSBC) indicating poor irrigation water.Hard water flows through the irrigation system of a farmer's field before it ever reaches the soil, leaving behind hard water deposits that eventually limit the effectiveness of water delivery to the plants.Watering zones may entirely block up over time, which is frequently the case with drip irrigation systems [61].Surendran et al. [62] confirmed the viability of using lowquality water for agriculture while also demonstrating the positive effects of magnetically treated irrigation water on crop development and output.Reverse osmosis (RO) systems are sometimes used by farmers to alleviate a variety of water problems, including hard water, in some specialized growth environments, such as greenhouses and hydroponics enterprises [63].RO, however, ultimately has no effect on treating hard water.Additionally, excessive amounts of calcium and magnesium, the minerals that make up the majority of hard water, lead to the fouling of pricey membranes that are essential to the functionality and effectiveness of RO systems.Large quantities of ozone are produced by agricultural ozone water treatment systems, which, when injected into water, instantly oxidize or remove unwanted pollutants for simple filtering.One of the main benefits of our ozone treatment system is that it is easily scalable, including our softeners, to be able to treat bigger volumes of contaminated irrigation water.The end result is soft water that is safe for crops and will not harm irrigation systems [64].The ability of electric vehicles to help improve air quality in cities and towns is their main advantage.Sun et al. [65] concluded that employing renewable energy during the manufacturing and battery production process would reduce CO 2 emissions, particularly in China and the USA.Battery electric vehicles were shown to be more energy-efficient.And, finally, to deal with the traffic congestion solutions, smart road design is recommended.Therefore, one of the easiest ways to lessen traffic congestion is to stop the problem of traffic congestion brought on by too many people trying to drive at once on any one road.In a civil engineer's design, providing several routes to the same destination can help reduce the number of vehicles in congested areas.Drivers spend less time waiting in traffic as a result of the traffic being distributed over all streets.Reducing the number of lanes available to private automobiles in favor of public transportation is another option.A civil engineer's plan can reduce the overall number of vehicles on the road by swapping out a few open roadway lanes for bus lanes, carpool lanes, or even sidewalks, as some potential drivers may choose to use another mode of transportation that is more cost-effective or better suits their lifestyle.There will inevitably be drivers who need or choose to operate their own automobiles.However, the likelihood of congestion can be decreased by lowering the overall number of vehicles on the road by offering alternate routes.
The need for a greater investment in public transport options across the nation is highlighted in a 2022 report by the United States Public Interest Research Group (US-PIRG).Reduced oil consumption (USPIRG estimates that even the current level of public transport utilization saves billions of gallons a year), less traffic congestion, and a smaller national environmental impact are cited as arguments for increased public transit use.(https://onlinemasters.ohio.edu/blog/traffic-congestion-problems-and-solutions/,accessed on 1 June 2023).

Conclusions
By using motor cars and engaging in other human activities that are common in urban areas, many pollutants, including dangerous species like heavy metals, reach the urban environment.Either these pollutants are instantly deposited on ground surfaces, such as roads, or they accumulate in the atmosphere first before reaching those surfaces.This study examines the impact of traffic congestion on the stormwater quality in urbanized regions and determines whether it is adequate for irrigation and drinking.In order to monitor and assess the stormwater quality, three different locations in Egypt's densely populated and urbanized Giza Governorate were chosen: Faisal (A), El Dokki (B), and Hadayek El-Ahram (C), which have respective catchment areas of 10,476, 7566, and 9870 m 2 , and monthly average daily traffic (MADT) values of 47,950, 20,919, and 27,064 cars.Six water samples were examined, and the physio-chemical and heavy metal stormwater quality indicators were compared with Egypt's water standards and World Health Organization (WHO) recommendations.The results show that the WQI ranged from 426 to 929, with an average of 661 ± 168, proving that each area under investigation had contaminated stormwater and required pretreatment in order for it to be useable.Therefore, the WQI of 776 and 708 for Faisal (A), 499 and 426 for El Dokki (B), and 929 and 626 for Hadayek El-Ahram (C) indicate that the water is unfit for drinking.Therefore, heavy metals like Al, Cr, Cd, Fe, and Cu were present in it.The stormwater quality irrigation indices of total dissolved solids (TDS), sodium adsorption ratio (SAR), soluble sodium percentage (SSP), permeability index (PI), magnesium adsorption ratio (MAR), and Kelley's ratio (KR), however, show excellent stormwater for irrigation, while total hardness (TH) and residual sodium bicarbonate (RSBC) show poor irrigation water quality.Strong linear correlations between heavy metals, total phosphorus (TP), and TSS were discovered.Based on the correlation between TSS, heavy metals, and TP that has been found, lowering the stormwater's suspended-solid levels would result in much lower particle-bound heavy metals and total phosphorus levels.The sites with the highest traffic volume recorded maximum stormwater pollution.The careful selection of the location for a single-sample collection is a crucial issue because the stormwater quality changes significantly during a specific event.The location should be favorable for stormwater and satisfy the following criteria: (i) the outfall locations, including longitude and latitude recurving water, are certain; (ii) the site drainage map, (iii) the estimation of the impervious area within each outfall drainage area, (iv) facility improvement which may affect the discharge described, (v) the facility's history of large leaks or spills of toxic or hazardous pollutants within the last three years, as well as the location and description of any existing structures and nonstructural pollutant sources like onsite materials that may come into contact with stormwater runoff, are all factors that should be considered.The obtained sampling data from stormwater flows, which is a useful tool for identifying pollutant sources, best management practices, and plans for preventing stormwater pollution, can be developed to prioritize eradicating these sources.There are alternatives, such as removing particle-bound pollution using non-structural preventive methods before it enters storm drain water, including street sweeping.Installing an adequate stormwater sewerage system is also advised to collect rainwater.In addition, the use of renewable energy throughout the manufacturing and battery production processes will lower CO 2 emissions, and battery electric vehicles are more energy-efficient.To deal with the traffic congestion solutions, (i) smart road design is recommended; and (ii) by substituting a few open roadway lanes for bus lanes, carpool lanes, or even sidewalks, a civil engineer's plan can decrease the overall number of vehicles on the road because some potential drivers might decide to use another mode of transportation that is more cost-effective or better suits their lifestyle, (iii) according to the United States Public Interest Research Group (USPIRG) report for 2022 that emphasizes the need for increased funding for public transportation alternatives across the country.Increased public transit usage is justified by claims of decreased oil consumption (USPIRG calculates that even current public transportation use saves billions of gallons annually), decreased traffic, and a milder national environmental impact.Finally, carrying out seasonal monitoring for stormwater quality is an important issue for the best management practices and policies for reducing stormwater pollution.
. The stormwater quality is assessed in three regions in urban areas of Giza, named Dokki, Hadayek El-Ahram, and Faisal regions.The urban area (Dokki) is located southwest of the Cairo city center; it is characterized by heavy traffic and other human activities that produce air pollutants such ozone, carbon dioxide, hydrocarbons, sulphur oxides, and suspended particulate matter.Hadayek El-Ahram is a district of central Giza.It is a middle-class and prosperous residential neighborhood.About 19 km from the center of Cairo and 14 km from Giza Square, Hadayek al-Ahram is situated close to Al Remaya Square, El Haram Street, and Faisal Street.

Figure 1 .
Figure 1.Map of the study area.

Sustainability 2023 , 23 Figure 2 .
Figure 2. Average data of the rainfall depth and average temperature in 2021.

Figure 2 .
Figure 2. Average data of the rainfall depth and average temperature in 2021.

Sustainability 2023 , 23 Figure 3 .
Figure 3. Locations of the stormwater sampling points A1 and A2, from Faisal Street; B1 and B2, from the El Dokki region; and C1 and C2, from the Hadayek El-Ahram region

Figure 3 .
Figure 3. Locations of the stormwater sampling points A1 and A2, from Faisal Street; B1 and B2, from the El Dokki region; and C1 and C2, from the Hadayek El-Ahram region.

Table 2 .
Description of the measurement points, catchment area, type of surface, and monthly average daily traffic (MADT).

Table 3 .
The relative weight of stormwater physicochemical parameters.

Table 4 .
[37]es of the water quality index for possible usage[37].

Table 5 .
Water quality indices for irrigation purposes.

Table 6 .
Indices for the stormwater classification of suitability for irrigation uses.

Table 7 .
Statistical analysis for the measured stormwater quality parameters in light of WHO and Egyptian water quality standards.

Table 8 .
WQI results for the studied regions.

Table 9 .
Stormwater irrigation indices' result for the collected samples.

Table 8 .
WQI results for the studied regions.

Table 9 .
Stormwater irrigation indices' result for the collected samples.