Spatial–Temporal Change Analysis and Multi-Scenario Simulation Prediction of Land-Use Carbon Emissions in the Wuhan Urban Agglomeration, China

: In the context of global warming, the Wuhan Urban Agglomeration is actively responding to China’s carbon peak and carbon neutrality goals and striving to achieve a reduction in carbon sources and an increase in carbon sinks. Therefore, it is critical to investigate carbon emissions from land use. This study uses the carbon emission coefﬁcient method to calculate carbon emissions from land use in the Wuhan Urban Agglomeration, analyzes its temporal and spatial changes and differences in urban structure, and couples with the Markov–PLUS model to simulate and predict the carbon emissions of four scenarios of land use in 2035. The research found the following: (1) during the Wuhan “1+8” City Circle stage, carbon sources and emissions increased steadily, with average annual growth rates of 1.92% and 1.99%, respectively. Carbon sinks remained stable and then decreased, with an average annual growth rate of − 0.46%. (2) During the Wuhan Metropolitan Area stage—except for 2020 and 2021, which were affected by COVID-19—carbon sources, sinks, and emissions continued to grow in general, and the average annual growth rates increased to 4.46%, 1.58%, and 4.51%, respectively. (3) In terms of urban structure differences, Wuhan is a high-carbon optimization zone; Xianning, Huangshi, and Huanggang are ecological protection zones; other cities, such as Ezhou, Xiaogan, and Xiantao are comprehensive optimization zones; and there is no low-carbon development zone. (4) The multi-scenario simulation results show that carbon sources and emissions are the highest under the economic development scenario, with values of 100.2952 and 9858.83 million tons, respectively, followed by cropland protection, natural development, and low-carbon development scenarios. Under low-carbon development, carbon sinks were the highest, with values of 1.9709 million tons, followed by natural development, economic development, and cropland protection scenarios. The research results are conducive to the formulation of carbon peak and neutrality goals as well as low-carbon development plans for the Wuhan Urban Agglomeration.


Introduction
With the rapid development of the world economy, the resulting environmental pollution problems have become increasingly apparent.In recent years, global warming caused by greenhouse gas emissions has become more and more serious [1][2][3][4].The United Nations Intergovernmental Panel on Climate Change (IPCC) pointed out in the report "Climate Change 2022: Impacts, Adaptation and Vulnerability" that global temperatures have increased by 1.06 • C compared to pre-industrial levels; if this rises to 1.5 • C, nearly 8% of the world's farmland will be unusable, which would be a disaster for mankind [5,6].In September 2020, General Secretary Xi Jinping promised at the 75th session of the United Nations General Assembly that China will achieve a carbon peak by 2030 and carbon neutrality by 2060 [7].Therefore, reducing the emissions of greenhouse gases, especially carbon dioxide, has become a severe challenge facing the world at present.A large number of studies have shown that land-use and land-cover change (LUCC) is an important factor affecting carbon emissions and absorption [8].LUCC changes the land-use type, and then affects the surface economy and human activities in the region, resulting in a change in carbon emissions and absorption, thereby affecting the balance of the carbon budget [9].Therefore, it is of great significance to study carbon emissions from land use to realize these carbon peak and carbon neutrality goals and control climate warming.
To date, a large number of studies on land-use carbon emissions have been conducted from multiple angles and aspects at home and abroad [10], including the calculation of emissions on multiple scales and for different regions and methods [11][12][13]; influencing factors [14,15]; economic, social, and ecological effects [7,16]; optimization and control methods [17,18], and predictions [19][20][21].The calculation of land-use carbon emissions can be summarized in two categories: "top-down" methods, starting from the social economy, including material balance, emission coefficients, actual measurements, and factor decomposition, and "bottom-up" methods, starting from ecological nature, including model simulations, sample plot inventories, and remote sensing estimations [22].Among them, the carbon emission coefficient method is widely used because of its simple operation and wide application range.For example, Jie Xu et al. [23] used this method to calculate the carbon emissions of different land-use types in Meishan City (except for built-up land, for which they used the carbon emission coefficient of energy consumption to indirectly perform an estimation).On the basis of the abovementioned method, Zhouliang Cao et al. [24] integrated people's breathing into the carbon emissions of built-up land in Shaanxi Province, which increased the accuracy of the results.Cavalcante Leite Christiane et al. [25] used this method to calculate the carbon emissions of LUCC, energy consumption, and other secondary sources in southern Brazil, and Alejandro Carpio et al. [26] used it to calculate the carbon dioxide emissions and absorption caused by LUCC in the process of urban expansion in Mexico.The prediction of land-use carbon emissions is mainly based on the prediction of changes in land-use types and then calculated through carbon emission coefficients.At present, commonly used models for land-use change predictions include Markov, cellular automaton (CA) [19], conversion of land use and its effects on a small regional extent (CLUE-S) [20], future land-use simulation (FLUS) [21], and so on.For example, Beroho Mohamed et al. [27] predicted the land use and cover of the Mediterranean Basin in Morocco in 2038, 2058, and 2050 based on the CA-Markov model; in the verification results, the kappa coefficient was 0.73.Liting Chen et al. [28] simulated and analyzed land use in the Raohe River Basin in 2035 based on the Markov-FLUS coupling model, with scenarios, such as inertial development, farmland protection, and ecological priority, in order to optimize land space allocation under different development goals.Kaiqi Zhang et al. [29] coupled the InVEST model carbon-storage module and the GeoSOS-FLUS model and analyzed the spatiotemporal characteristics of carbon storage within six districts and eleven counties in the city of Guilin from 2000 to 2040 based on land-use data and future land prediction results in different scenarios.However, the CA model does not explore the relationship between land-use spatial change and spatial driving factors, which may lead to low simulation accuracy.CLUE-S belongs to the spatial model, which strengthens the spatial allocation module but ignores the possibility of the conversion of nondominant land types, resulting in low accuracy.The FLUS model only performs follow-up simulations based on the land-use data of the first period and does not have time attributes, resulting in insufficient simulation accuracy.The patch-generating land-use simulation model (PLUS) [30] is a rule-mining framework based on the land-expansion analysis strategy (LEAS) and a CA model based on multi-type random seeds (CARSs).This model not only retains the calculation process of the suitability probability based on the driving factors in the FLUS model, but also combines the sample training based on the conversion of various types of land-use data between the two periods in the CA model.Compared with other models, it can better improve the simulation accuracy of land-use types.Fanghu Sun et al. [31], for Anhui Province, analyzed the temporal and spatial evolution characteristics of land-use types and carbon storage from 1990 to 2018 by coupling the carbon storage module of the InVEST and PLUS models and predicted the change trends of carbon storage in 2034 and 2050 for natural development and ecological protection scenarios.Ziyao Wang et al. [32] used Bortala Mongolian Autonomous Prefecture as an example to conduct ecological zoning planning by coupling the InVEST-HFI-PLUS model to evaluate the habitat quality and human footprint index in the study area, as well as to dynamically evaluate the level of ecosystem services in different scenarios.In previous studies on land-use carbon emissions, the selection of carbon emission coefficients was a crucial step.The regional differences in carbon emission coefficients of built-up land are significant; therefore, selecting a suitable coefficient for the research area is urgent.Previous studies on predicting carbon emissions were often only conducted by limiting the quantity transfer of land-use types.This is a single method, with which it is difficult to truly simulate the real situation.Therefore, how to better simulate the quantity and spatial changes of land-use types in different scenarios, and thus simulate land-use carbon emissions, needs improvement.
Since Hubei Province first proposed the concept of the Wuhan Urban Agglomeration in April 2003, it has been committed to creating the Wuhan "1+8" City Circle to drive the development of cities around Wuhan.As the economic center of Hubei Province, Wuhan's economy is developing rapidly; however, it also produces a high level of carbon emissions.However, the economic volume of Wuhan makes it difficult to drive the development of the entire City Circle.In 2017, Hubei Province proposed to delineate the Wuhan Metropolitan Area within the scope of the "1 h commuting circle" as an optimization of the City Circle.Taking transportation first, the "146" spatial pattern of one core (Wuhan), four belts (Wuehuanghuang, Wuxian, Hanxiao, and Wuxian urban belts), and six pairs (Ezhou, Huangshi, Xiaogan, Huanggang, Xianning, and Xiantao) was constructed to promote the coordinated development of regional society, economy, and ecology in all aspects [33][34][35][36].Questions worth studying since the establishment of the Wuhan Urban Agglomeration include: what is the development trend of the carbon emissions of the cities and counties within this range, after delineating the Wuhan Metropolitan Area?What changes have occurred in the carbon emissions of each city and county compared with the previous ones?Finally, what is the future development trend?Therefore, based on the carbon emission coefficient method, this paper modifies factors through energy data to study land-use carbon emissions in the Wuhan Urban Agglomeration in two stages.Coupled with the Markov and PLUS models, this paper simulates and predicts carbon emissions from land use under different scenarios in 2035 by limiting the quantity and space of land use.The study of land-use carbon emissions in this region cannot only reflect the development process and pattern of the Wuhan Urban Agglomeration, but can also provide effective theoretical support and suggestions for future development planning through scenario simulation predictions.The carbon emission factor correction and land-use transfer restriction methods applied by the research institute are also expected to improve the universality of land-use carbon emission research and provide suggestions and references for it in different regions of the world.

Study Area
The Wuhan Urban Agglomeration (Figure 1) is centered in Wuhan City, with a radius of about 100 km.It is divided into nine cities, namely, Wuhan, Huangshi, Ezhou, Xiaogan, Huanggang, Xianning, Xiantao, Tianmen, and Qianjiang, with a total area of 58,025 square kilometers, accounting for 31.21% of the province's total area.In 2020, the resident population was 3248.88 million, accounting for 55.16% of the province's population; the gross domestic product (GDP) was CNY 26,361.01 billion, accounting for 60.38% of the province's GDP [37].With the advantages, such as its unique location, dense industry and personnel distribution, and national strategic support, the Wuhan Urban Agglomeration has developed rapidly and has become an important strategic fulcrum for the development of Hubei Province and the central region.According to the "14th Five-Year Plan for Natural Resources Protection and Development of Hubei Province" promulgated in 2021, reaching carbon peak and neutrality is an opportunity and a challenge for the province, which is taking the lead in realizing the green development in Central China.As a pioneer in the economic, social, and ecological development of Hubei Province, the Wuhan Urban Agglomeration views the realization of carbon peak and neutrality goals as an important task.

Data Sources
In this study, 1 km of land-use data in 2000, 2005, 2010, and 2015 was used to calculate land-use carbon emissions, in order to explore their spatiotemporal patterns in the Wuhan Urban Agglomeration during the Wuhan "1 + 8" City Circle" stage.Sentinel-2 images (10 m) from 2017 to 2022 were used for supervision classification to obtain land-use types; land-use carbon emission calculations were conducted to explore the spatiotemporal patterns of land-use carbon emissions in the Wuhan Urban Agglomeration during the Wuhan Metropolitan Area stage; and the emission results from 2020 were selected to explore the regional differences.According to the relevant research [38][39][40], and considering the availability, quantification, and correlation of the data with land-use types, a total of 12 factors (Table 1), including terrain, meteorology, soil, location, economy, and grain resources, were selected as the driving factors of the PLUS model to simulate and predict land-use changes and land-use carbon emissions.The data sources needed for the experiment are listed in Table 2.

Data Sources
In this study, 1 km of land-use data in 2000, 2005, 2010, and 2015 was used to calculate land-use carbon emissions, in order to explore their spatiotemporal patterns in the Wuhan Urban Agglomeration during the Wuhan "1+8" City Circle" stage.Sentinel-2 images (10 m) from 2017 to 2022 were used for supervision classification to obtain land-use types; land-use carbon emission calculations were conducted to explore the spatiotemporal patterns of land-use carbon emissions in the Wuhan Urban Agglomeration during the Wuhan Metropolitan Area stage; and the emission results from 2020 were selected to explore the regional differences.According to the relevant research [38][39][40], and considering the availability, quantification, and correlation of the data with land-use types, a total of 12 factors (Table 1), including terrain, meteorology, soil, location, economy, and grain resources, were selected as the driving factors of the PLUS model to simulate and predict land-use changes and land-use carbon emissions.The data sources needed for the experiment are listed in Table 2.

Data Processing
The supervised classification of land-use types was conducted.Sentinel-2 remote sensing images from 2017 to 2022 were selected, and after preprocessing techniques, such as radiometric calibration and atmospheric correction, a classification was conducted in ENVI5.3.The classification system was based on the planning division of the 2007 national standard "Classification of Land Use Status", combined with the existing situation of the Wuhan City Circle, and divided the land-use types into cropland, forest land, grassland, water, built-up land, and unused land.These were combined with Google Earth images to establish interpretation signs and obtain the final land-use type data.The slope was calculated using the slope tool in Arcgis 10.4.1 using DEM data.The shortest distances of highways, railways, and water systems were calculated using the Euclidean distance tool in Arcgis10.4.1 using road network and water system data.This study used the carbon emission coefficient method to calculate land-use carbon emissions, including carbon absorption (carbon sinks) generated by forest land, grassland, water, and unused land, and carbon emissions (carbon sources) generated by cropland and built-up land.Cropland, forest land, grassland, water, and unused land were calculated using the direct measurement method [41], and the calculation formula is as follows: where C direct is the direct carbon emission; C i represents the carbon sources and carbon sinks of the i-th land-use type (positive value is carbon source, negative value is carbon sink); A i is the area of the i-th land-use type; and F i is the carbon emission coefficient of the i-th land-use type.For cropland, there were significant differences in carbon emissions due to different crops planted in different regions.Therefore, this study determined the carbon emission coefficient of cropland suitable for the Wuhan Urban Agglomeration based on the research on land-use carbon emissions in Hubei Province [41].The regional differences in land-use types, other than built-up land and cropland, were relatively small.Therefore, for forestland and grassland, based on the research results of Jingyun Fang [42] and combined with other relevant literature [41,[43][44][45], this study determined the carbon emission coefficient suitable for the Wuhan Urban Agglomeration by taking the median of its research results.For water, based on the research results of Li Lai [46] and Xiaonan Duan [47], the average value was taken as the carbon emission of water.For unused land, this study determined the carbon emission coefficient commonly used in the relevant literature [41,[43][44][45].The coefficients of cropland, forestland, grassland, water, and unused land were determined to be 0.497, −0.581, −0.021, −0.253, and −0.005 t(C)/(hm 2 •a), respectively.
Since 80-90% of the carbon emissions of built-up land come from the combustion of fossil fuels [24,[48][49][50], built-up land was calculated using an indirect estimation method [41], and the calculation formula is as follows: where C indirect is the amount of indirect carbon emissions, α is the conversion of various energy sources into standard coal consumption, and β is the carbon emission coefficient corresponding to standard coal.The results of converting various types of energy into standard coal were obtained from the statistical yearbooks of each city.The carbon emission coefficient was obtained according to IPCC2006, which was 0.5404 t(C)/t.Since the statistical yearbooks for 2021 and 2022 have not yet been published, the energy consumption data could not be obtained.Moreover, some cities and counties did not have statistical energy data before 2016.Therefore, the direct measurement method was used again to estimate the carbon emissions of built-up land.The carbon emission coefficient was calculated using the indirect estimation method based on the energy data from previous years and the area of built-up land.The calculation formula is as follows: where F b is the carbon emission coefficient of built-up land; C j is the carbon emissions from built-up land in year j, calculated using the indirect estimation method; A j is the built-up land area in the j-th year; and m is the total number of years used to calculate the carbon emission coefficient.The final calculated carbon emission coefficient for built-up land was 102.57t(C)/(hm 2 •a).

Evaluation of Land-Use Carbon Emission Pattern
Carbon source intensity (C e ) [51][52][53] and carbon sink intensity (C s ) [54][55][56] were selected to more accurately reflect the real situation of land-use carbon emissions in each city.The carbon source intensity indicates the number of carbon sources required per unit of GDP in the region, and the carbon sink intensity indicates the number of carbon sinks generated per unit of land area in the region.The calculation formula is as follows: where E p is the total carbon source, G p is the GDP, S p is the total amount of carbon, and A p is the land area.
The economic contribution coefficient of carbon sources (ECC) [41,[57][58][59] and the ecological carrying capacity of carbon sinks (ESC) [41,[59][60][61] were selected to analyze the carbon emission patterns of cities in the Wuhan Urban Agglomeration.The carbon source economic contribution coefficient is a standard that reflects the economic efficiency of carbon emissions in a region and can measure the contribution of carbon emissions to economic development; the carbon sink ecological carrying coefficient is a standard that reflects the carbon sink absorption capacity in the region and can measure the region's contribution to carbon absorption.The calculation formula is as follows: where G n is the GDP of the nth city and county, G is the GDP of the Wuhan Urban Agglomeration, E n is the total carbon sources in the nth city, E is the total carbon sources in the Wuhan Urban Agglomeration, S n is the carbon accumulation in the nth city, and S is the carbon accumulation of the Wuhan Urban Agglomeration.If ECC > 1, it means that the city's carbon source economic contribution and the carbon emission economic efficiency are higher, and vice versa; if ESC > 1, it indicates that the city's carbon sink ecological carrying coefficient and the carbon absorption capacity are higher, and vice versa.

Accuracy Verification and Scenario Presupposition of the PLUS Model
The PLUS model is a rule mining framework based on the land-expansion analysis strategy (LEAS) and a CA model based on the multi-type random seed (CARS) [19].The model is mainly divided into two parts: the first part (LEAS) compares the land-use-type data for the two periods, samples the expansion of various types of land use, and uses the random forest algorithm to mine the driving forces of various factors for the expansion of each land-use type, ultimately capturing their development probabilities and the extent to which all drivers contribute to their expansion.The second part (CARS) combines multi-type random seed generation and the threshold decrease mechanism to dynamically present the land-use change process, including the spatial change, area change, and change curve of each land-use type [62][63][64].
Taking the land use of the Wuhan Urban Agglomeration in 2017 as the starting layer, the land use in 2020 was simulated and the simulation results were compared with the land use at present in 2020.The kappa and FoM coefficients were used to evaluate the prediction results.In the verification results, the kappa coefficient was 0.87, the overall accuracy was 90%, and the FoM coefficient was 0.126.This shows that the PLUS model is more accurate in simulating and predicting the land-use types in the Wuhan Urban Agglomeration, and thus can be used to predict future land-use types.
Based on the development trend and related policies of the Wuhan Urban Agglomeration, this study simulated and predicted land-use types under the four scenarios of natural development, low-carbon development, economic development, and cropland protection through constraints on land-use quantity and land-use spatial transfer, and then predicted the spatial patterns of land-use carbon emissions based on the results.In terms of land-use quantity constraints, we referred to the results of the land-use transfer matrix from 2017 to 2020 and used the Markov model to predict the number of land-use types in 2035 as the input of the PLUS model.In terms of land-use spatial transfer restrictions, according to the matrix under different scenarios, we selected the case where the conversion ratio exceeded 1% of the total area of the land type as the allowed conversion.The specific constraints were as follows: under natural development, the transfer probability of each land-use type remained unchanged and the spatial transfer was not restricted; under low-carbon development, the probability of grassland and forest land transfer to built-up land was reduced by 30%, the probability of built-up land and unused land transfer to grassland and forest land increased by 20% and spatial transfer limited the transfer of forest land to cropland and built-up land; under economic development, the probability of transferring grassland and woodland to built-up land was increased by 20%, the probability of transferring unused land to built-up land was increased by 30%, the probability of transferring built-up land to grassland and forest land was reduced by 30%, and no restrictions were placed on spatial transfer; under cropland protection, the probability of transferring cropland to other land uses was reduced by 30%, and the probability of transferring grassland, forest land, unused land, and built-up land to cropland was increased by 10%.Spatial transfer limited the transfer of cropland to unused land and built-up land.

Trend Analysis of Land-Use Carbon Emissions in the Wuhan Urban Agglomeration from 2000 to 2015
Figure 2 shows the results for the calculations of land-use carbon emissions in the Wuhan Urban Agglomeration in 2000, 2005, 2010, and 2015 using the carbon emission coefficient method.From 2000 to 2015, the number of carbon sources showed a continuous growth trend, with an average annual growth rate of 1.92%.The growth rate from 2000 to 2010 was relatively slow, with an annual average of 1.13%, and the growth rate from 2010 to 2015 was relatively fast, with an annual average of 3.51%.The growth trend of carbon emissions was roughly the same as that of carbon sources, with an annual average of 1.17% from 2000 to 2010 and 3.67% from 2010 to 2015.This may have been because, in 2010, the Wuhan Urban Agglomeration was listed as a key development area in the "12th Five-Year Plan" of the country, and this rapid economic development brought about inevitable carbon emissions; the carbon source intensity decreased significantly from 2000 to 2015, indicating that, with the upgrading of technology and economic development, the number of carbon sources required per unit of GDP was greatly reduced.From 2000 to 2015, carbon sinks decreased slightly, with an average annual growth rate of −0.46%.From 2000 to 2010, the number and intensity of carbon sinks were basically stable, and from 2010 to 2015, there was a slight decline, and the average annual growth rate of carbon sinks was −1.45%.This may have also been due to the transformation of ecological land into built-up land due to rapid economic development, resulting in a reduction in carbon sinks and carbon sink intensity [65].The results show that, during the period of the Wuhan "1+8" City Circle from 2000 to 2015, the carbon emission of land use in the Wuhan Urban Agglomeration emphasized economic development but ignored ecological protection to a certain extent.This model led to the stagnation-and even a retreat-of the pace of ecological protection, which, in turn, led to the continuous growth of carbon emissions and increasingly serious ecological pollution.Figure 3 shows the results for the calculations of land-use carbon emissions in the Wuhan Urban Agglomeration from 2017 to 2022 using the carbon emission coefficient method.The average annual growth rates of carbon sources, sinks, and emissions from 2017 to 2022 were 4.46%, 1.58%, and 4.50%, respectively.From 2017 to 2019, the number of carbon sources and emissions showed a continuous growth trend with average annual growth rates of 9.49% and 9.59%, respectively.From 2019 to 2021, it showed a downward trend with average annual growth rates of −4.33% and −4.49%, respectively.From 2021 to 2022, there was a significant rebound, with average annual growth rates of 13.34% and 13.78%, respectively.Perhaps, due to the impacts of COVID-19 in 2020 and 2021, the Wuhan Urban Agglomeration was sealed off in multiple time periods and locations, which led to a stagnant state of urban development [66,67].Many enterprises that have a greater impact on carbon sources closed down, resulting in a significant reduction in carbon sources and carbon emissions.In 2022, the impact of the pandemic weakened, with only some areas being sealed off from October to November.By December, the restrictions were fully lifted and the economy rebounded.The construction of major enterprises also brought about an increase in carbon emissions.Compared with the sharp reduction in 2000-2015, the carbon source intensity basically remained stable.From 2017 to 2021, the number and intensity of carbon sinks showed a slow growth trend with an average annual growth rate of 4.51%, which was inseparable from the emphasis on ecological green development in Hubei Province in recent years.In 2022, there was a significant downward trend with an average annual growth rate of −9.33%.This may also have been because, in 2022, when the impact of COVID-19 was relatively weak, the economic recovery led to the expansion of the built-up land area and the occupation of ecological land, resulting in a reduction in carbon sinks and carbon sink intensity.The results show that, from 2017 to 2022, the carbon emissions from land use in the Wuhan Metropolitan Area stage not only ensured stable economic development, but also strengthened ecological protection and development.This model ensured that economic development and ecological protection went hand in hand.Although it is still difficult to change the trend of carbon emission growth, it has slowed down to a certain extent.In particular, the two years of COVID-19 restrictions achieved a negative-growth trend for carbon emissions.

Differences in the Urban Structure of Carbon Emissions from Land Use in the Wuhan Urban Agglomeration in 2020
From the 2020 map of land-use types in the Wuhan Urban Agglomeration (Figure 4) and the area map of land-use types in each city (Figure 5), it can be seen that the area of forest land is relatively large, accounting for 41.47%, followed by cropland, built-up land, and water, accounting for 20.72%, 15.98%, and 15.02%, respectively.From the perspective of cities, the land-use structures in Huangshi, Xianning, and Huanggang are relatively similar, and forest land accounts for the largest proportion, being greater than 45%.The three cities of Xiantao, Tianmen, and Qianjiang are dominated by cropland, which accounts for more than 45% of the city area.The three cities of Wuhan, Ezhou, and Xiaogan

Differences in the Urban Structure of Carbon Emissions from Land Use in the Wuhan Urban Agglomeration in 2020
From the 2020 map of land-use types in the Wuhan Urban Agglomeration (Figure 4) and the area map of land-use types in each city (Figure 5), it can be seen that the area of forest land is relatively large, accounting for 41.47%, followed by cropland, built-up land, and water, accounting for 20.72%, 15.98%, and 15.02%, respectively.From the perspective of cities, the land-use structures in Huangshi, Xianning, and Huanggang are relatively similar, and forest land accounts for the largest proportion, being greater than 45%.The three cities of Xiantao, Tianmen, and Qianjiang are dominated by cropland, which accounts for more than 45% of the city area.The three cities of Wuhan, Ezhou, and Xiaogan have a relatively balanced area of cropland, forest land, and water.From the perspective of the overall spatial distribution, the built-up land in the Wuhan Urban Agglomeration is concentrated in the downtown area of Wuhan, and the rest of the built-up land is evenly distributed in clusters; most of the water is in the lakes, mainly surrounding the central city of Wuhan; cropland is mainly concentrated on the west side and a small amount is also concentrated on the southeast side; and forest land is mainly distributed in the Mufu Mountains in the south and Dabie Mountains in the northeast.

Differences in the Urban Structure of Carbon Emissions from Land Use in the Wuhan Urban Agglomeration in 2020
From the 2020 map of land-use types in the Wuhan Urban Agglomeration (Figure 4) and the area map of land-use types in each city (Figure 5), it can be seen that the area of forest land is relatively large, accounting for 41.47%, followed by cropland, built-up land, and water, accounting for 20.72%, 15.98%, and 15.02%, respectively.From the perspective of cities, the land-use structures in Huangshi, Xianning, and Huanggang are relatively similar, and forest land accounts for the largest proportion, being greater than 45%.The three cities of Xiantao, Tianmen, and Qianjiang are dominated by cropland, which accounts for more than 45% of the city area.The three cities of Wuhan, Ezhou, and Xiaogan have a relatively balanced area of cropland, forest land, and water.From the perspective of the overall spatial distribution, the built-up land in the Wuhan Urban Agglomeration is concentrated in the downtown area of Wuhan, and the rest of the built-up land is evenly distributed in clusters; most of the water is in the lakes, mainly surrounding the central city of Wuhan; cropland is mainly concentrated on the west side and a small amount is also concentrated on the southeast side; and forest land is mainly distributed in the Mufu Mountains in the south and Dabie Mountains in the northeast.We used the carbon emission index method to calculate the carbon sources, carbon sinks, carbon emissions, carbon source intensity, carbon sink intensity, carbon source economic contribution coefficient, and carbon sink ecological carrying coefficient for the nine cities in the Wuhan Urban Agglomeration in 2020, as shown in Table 3. Spatial visualization processing was performed on the abovementioned parameters, as shown in Figure 6.In the Wuhan Urban Agglomeration, Huanggang had the largest number of carbon We used the carbon emission index method to calculate the carbon sources, carbon sinks, carbon emissions, carbon source intensity, carbon sink intensity, carbon source economic contribution coefficient, and carbon sink ecological carrying coefficient for the nine cities in the Wuhan Urban Agglomeration in 2020, as shown in Table 3. Spatial visualization processing was performed on the abovementioned parameters, as shown in Figure 6.In the Wuhan Urban Agglomeration, Huanggang had the largest number of carbon sources, followed by Wuhan.The total carbon sources of the two accounted for 49% of the total amount in the Wuhan Urban Agglomeration.Qianjiang had the lowest number of carbon sources, accounting for only 3.6% of the total amount.This was more consistent with the development of the Wuhan Urban Agglomeration.As the leader in the development of the Wuhan Urban Agglomeration, Wuhan's economy and development speed far exceed those of other cities, which inevitably leads to a large proportion of carbon sources in Wuhan.As its largest city, Huanggang accounts for 30% of the total area of the Wuhan Urban Agglomeration; therefore, its carbon source is also larger than in the other cities.Huanggang had the largest carbon sink, followed by Xianning.The carbon accumulation of the two accounted for 61% of the Wuhan Urban Agglomeration.The carbon sink of Qianjiang was the smallest, accounting for only 0.8% of the total Wuhan Urban Agglomeration.This was inseparable from the distribution of forest land.The Dabie and Mufu Mountains are in the jurisdictions of Huanggang and Xianning, respectively.They have rich forest resources and, therefore, a large carbon sink.The proportion of carbon emissions was basically the same as the proportion of carbon sources.This was because the carbon accumulation in the Wuhan Urban Agglomeration was relatively low, at only 2% of the total carbon sources.Therefore, it was difficult for the carbon sinks to have a greater impact on the carbon emissions, and the number of carbon sources determined the level of carbon emissions to a certain extent.The carbon source intensity of Wuhan is lower than that of the Wuhan Urban Agglomeration overall, indicating that the number of carbon sources required to produce unit economic benefits is relatively small, and the carbon source utilization efficiency is relatively high.The carbon sink intensities of Huangshi, Xianning, and Huanggang were greater than that of the Wuhan Urban Agglomeration as a whole, indicating that these three cities had more carbon sinks per unit land area and stronger carbon sink absorption capacities.According to the ECC and ESC, the nine cities in the Wuhan Urban Agglomeration are divided into four types of zones, shown in Table 4.As shown in Figure 7, there is no low-carbon development zone in the Wuhan Urban Agglomeration.Wuhan is the only high-carbon optimization zone and its carbon source economic contribution coefficient is as high as 2.79.Ecological protection zones are concentrated in the east and south, including Xianning, Huangshi, and Huanggang.Among them, the carbon sink ecological carrying coefficient of Huanggang, which was the city that made the greatest contribution to the ecological protection of the Wuhan Urban Agglomeration, was as high as 2.36.The carbon sink ecological carrying coefficient of Huangshi was only 1.03, which shows that Huangshi still has great potential as an ecological protection zone.Comprehensive optimization zones were mainly concentrated in the northwest, including Ezhou, Xiaogan, Xiantao, Tianmen, and Qianjiang.Among them, the economic contribution coefficient of carbon sources in Ezhou was 0.98, and it is very likely to become the next high-carbon optimization zone, making further contributions to the economic development of the Wuhan Urban Agglomeration.The economic contribution coefficient of carbon sources in Tianmen was 0.46 and the ecological carrying coefficient of carbon sinks was 0.17.The road to economic development and ecological protection in Tianmen is long and difficult, and there is still a lot of room for development and progress.
(10,000 Tons) (  According to the ECC and ESC, the nine cities in the Wuhan Urban Agglomeration are divided into four types of zones, shown in Table 4.As shown in Figure 7, there is no low-carbon development zone in the Wuhan Urban Agglomeration.Wuhan is the only high-carbon optimization zone and its carbon source economic contribution coefficient is as high as 2.79.Ecological protection zones are concentrated in the east and south, including Xianning, Huangshi, and Huanggang.Among them, the carbon sink ecological carrying coefficient of Huanggang, which was the city that made the greatest contribution to the ecological protection of the Wuhan Urban Agglomeration, was as high as 2.36.The carbon sink ecological carrying coefficient of Huangshi was only 1.03, which shows that Huangshi still has great potential as an ecological protection zone.Comprehensive optimization zones were mainly concentrated in the northwest, including Ezhou, Xiaogan, Xiantao, Tianmen, and Qianjiang.Among them, the economic contribution coefficient of  Wuhan, as the only high-carbon optimization zone, is the leader in development and plays an extremely important role in the economic development of the entire Wuhan Urban Agglomeration.However, it should also pay attention to the accumulation of carbon sinks, adopt methods, such as carbon compensation and carbon trading, and strive to make positive contributions to ecological protection.Xianning, Huangshi, and Huanggang are ecological protection zones with a high number of forested areas.They should strictly abide by the bottom-line rules of ecological environment protection, provide full play to their natural advantages, and conduct green development measures.Ezhou, Xiaogan, Xiantao, Tianmen, and Qianjiang are comprehensive optimization zones.While the economic development of these areas is insufficient, the carbon sink function is also poor.They should adjust their industrial structure, optimize their industrial layout, and achieve rapid development, while ensuring the lowest possible carbon levels.There is no low-carbon development zone in the Wuhan Urban Agglomeration, which shows that the positioning of the city's main functions is quite different, and there is a lack of cities that can both ensure economic development and achieve low-carbon protection.Therefore, cities should develop green industries and strive towards the goal of becoming low-carbon development zones.
cities should develop green industries and strive towards the goal of becoming low bon development zones.

Prediction of Land-Use Carbon Emissions under a Multi-Scenario Simulation of the Wuhan Urban Agglomeration
The Markov-PLUS model was used to predict the land-use types in natural development, low-carbon development, economic development, and cropland protection scenarios in the Wuhan Urban Agglomeration in 2035.The quantitative results are shown in Table 5 and the spatial results are shown in Figure 8.It can be seen from Table 5 that the unused land area under the four scenarios remains almost unchanged, with only small fluctuations: in terms of grassland area, the three scenarios of low-carbon development, economic development, and cropland protection are almost all the same and are all better than the natural development scenario; the cropland area under the cropland protection scenario is much better than the other three scenarios, followed by economic development, natural development, and low-carbon development; in terms of built-up land area, the economic development scenario is the best, the cropland protection and natural development scenarios are similar, and the low-carbon development is the worst; the forest land area is largest under low-carbon development, followed by natural development, economic development, and cropland protection; the water area under natural development, low-carbon development, and economic development is not very different, while it is the lowest under the cropland protection scenario.It can be seen from Figure 8 that the spatial distribution of unused land and grassland presents little change; the change in the distribution of cropland is mainly due to the fact that, under the cropland protection scenario, there are different degrees of area increase in the west and southeast of the Wuhan Urban Agglomeration, including Qianjiang, Tianmen, Xiantao, the south of Xiaogan, the southwest of Wuhan, and the southeast of Huanggang, compared with the other three scenarios.The change in the distribution of built-up land was mainly due to its expansion, according to the original built-up land area under the economic development scenario.The key expansion areas were the central urban area of Wuhan, the southwest of Tianmen, and multiple urban areas in Xiaogan.The changes in the distribution of forest land were mainly due to low-carbon development.The northeastern and southern regions of the Wuhan Urban Agglomeration included the northern part of Xiaogan and the expansion of forest land in Huanggang, Xianning, and Huangshi.The distribution of water did not change much.The reduced water under the cropland protection scenario was mainly at the edge of the lake and reservoir area, and this part of the area was transformed into built-up land.The main differences in the simulation results of the four different scenarios lie in cropland, built-up land, forest land, and water.Under low-carbon development, the area of forest land increased significantly compared with the other scenarios, while built-up land and cropland decreased slightly.This was mainly because, in the simulated low-carbon scenario, the use of afforestation to reduce carbon caused forest land to occupy built-up land and cropland, and reducing these can also achieve low-carbon development to a certain extent.Under the scenario of economic development, the area of built-up land increased significantly; the area of cropland also increased to a certain extent, compared with natural development and low-carbon development; and the area of forest land decreased.This was because, in the scenario of simulated economic development, vigorously developing the economy led to the continuous expansion of cities and towns, and the area of cropland also increased to meet the basic needs of population expansion, which causes a significant encroachment on forest land, and thus, deforestation.Under the condition of cropland protection, the area of cropland expanded rapidly and the area of forest land and water decreased significantly.This was mainly because, in the context of cropland protection, on the one hand, it was necessary to ensure that cropland would not be encroached on by other land-use types and, on the other hand, its development was realized by pushing the distribution of mountains and reclaiming land from the lakes.We used the carbon emission index method to further calculate the results of land-use carbon emissions in the Wuhan Urban Agglomeration under a multi-scenario simulation prediction, as shown in Tables 6 and 7. Overall, the carbon sources in the Wuhan Urban Agglomeration were the highest under the economic development scenario, with 98.5883 million tons, followed by cropland protection, natural development, and lowcarbon development; carbon sinks were the highest under the low-carbon development scenario, with 1.9709 million tons, followed by natural development, economic development, and cropland protection; and carbon emissions were ranked in line with carbon sources.Combined with the quantity of each land-use type under the scenario simulation prediction mentioned above, it can be seen that, under the low-carbon development scenario, the considerable increase in the forest land area reduced both the area of built-up land and carbon emissions; under economic development, the built-up land and carbon emissions increased considerably; in the case of cropland protection, the area of cropland increased substantially, most of which was occupied by forest land and water; and the area of built-up land remained stable.Therefore, the increase in carbon emissions was slightly lower.From the city's point of view, for the scenarios of natural development and low-carbon development, Wuhan had the highest number of carbon sources, while, for the scenarios of economic development and cropland protection, Huanggang surpassed Wuhan in this regard.For the scenarios of natural development, low-carbon development, and economic development, Ezhou had the lowest number of carbon sources, while Qianjiang had the lowest cropland protection.Huanggang was always the city with the most carbon sinks; Qianjiang was the city with the lowest number of carbon sinks under the natural development, low-carbon development, and economic development scenarios; and Tianmen was the city with the lowest number of carbon sinks under the cropland protection scenario.Under the natural development, low-carbon development, and economic development scenarios, Wuhan had the highest carbon emissions and Ezhou had the lowest.Under the cropland protection scenario, Huanggang had the highest carbon emissions, while Qianjiang had the lowest.We used the carbon emission index method to further calculate the results of landuse carbon emissions in the Wuhan Urban Agglomeration under a multi-scenario simulation prediction, as shown in Tables 6 and 7. Overall, the carbon sources in the Wuhan Urban Agglomeration were the highest under the economic development scenario, with 98.5883 million tons, followed by cropland protection, natural development, and low-carbon development; carbon sinks were the highest under the low-carbon development scenario, with 1.9709 million tons, followed by natural development, economic development, and cropland protection; and carbon emissions were ranked in line with carbon sources.Combined with the quantity of each land-use type under the scenario simulation prediction mentioned above, it can be seen that, under the low-carbon development scenario, the considerable increase in the forest land area reduced both the area of built-up land and carbon emissions; under economic development, the built-up land and carbon emissions increased considerably; in the case of cropland protection, the area of cropland increased substantially, most of which was occupied by forest land and water; and the area   It was found that the carbon sources were mainly composed of built-up land; therefore, the change in the built-up land area determined the size of a carbon source, to a certain extent.Therefore, how to control the expansion of built-up land in future planning is particularly important for "source reduction".On the one hand, it is necessary to perform reasonable planning for the development of the city and to set up a buffer zone for urban expansion in advance at the edge of the city, in case urban development leads to the occupation of forest land and other carbon sink areas.On the other hand, it is necessary to properly control expansion and development, pay more attention to the development mode centered on efficiency, reduce the intensity of carbon sources, and improve the efficiency of carbon source utilization.Carbon sinks are mainly composed of forest land; therefore, increasing the area of forest land is an important means of "increasing sinks".In future planning, on the one hand, it is necessary to protect the existing forest land and prevent the loss of forest land caused by human factors, such as the expansion and occupation of built-up land, as well as natural factors, such as forest fires.On the other hand, in cities, it is necessary to coordinate and connect green, public, open spaces, such as small parks, small green spaces, and small forests, and build urban green corridors to achieve effective green growth.The number of carbon sources is far higher than the number of carbon sinks.On the one hand, this shows that the impact of carbon sources on carbon emissions is far greater than that of carbon sinks."Reducing sources" can reduce carbon emissions more rapidly than "increasing sinks".On the other hand, it also shows that there is still a large gap between the situation at present in the Wuhan Urban Agglomeration and the goal of achieving carbon neutrality.Effectively increasing the number of carbon sinks is a more important means of achieving carbon neutrality after the carbon peak is achieved.From the perspective of cities, by comparing the carbon emission results for the Wuhan Urban Agglomeration in 2020, it can be observed that Wuhan and Huanggang have always been the two cities with the highest proportion of carbon emissions.Carbon emissions in Xiaogan will also gradually increase, and it will become a city with the highest carbon emissions after Wuhan and Huanggang.These three cities will always be the key areas of "source reduction".The forestland areas in Huanggang, Xiaogan, and Wuhan are the most susceptible to the impact of different planning methods, resulting in considerable changes in carbon sinks, indicating that the forestland in these three cities needs to be protected, and other land-use methods should be avoided as much as possible.The carbon emissions from Tianmen under the cropland protection scenario remain at the same level as in 2020, while the other three scenarios produced a considerable increase.This indicates that Tianmen may be the next key city for vigorous development, and it may also become a high-carbon optimization area that urgently needs to reduce carbon levels.How to reduce the increase in carbon emissions caused by urban development as much as possible is an issue that needs to be focused on in Tianmen's development planning.

Discussion of the Findings
We selected the experimental results from land-use carbon emissions from 2000 to 2015 and compared them with the existing research results for the Wuhan Urban Agglomeration to verify the accuracy of this article.Compared with the results of En Chen [68], the calculated carbon sources, sinks, and emissions in this article were all lower.The reasons for the differences were as follows: En Chen's research divided cropland into two parts for the calculations, namely, carbon sources and carbon sinks.However, this paper comprehensively calculated the D-value between the carbon sources and carbon sinks of cropland, resulting in less of both.Both calculation methods can be used.The former can reflect the different effects of arable land as a carbon source and sink in more detail, while the latter directly reflects the final presentation state of arable land, making the calculation more convenient.En Chen added carbon emissions from the tertiary industry and population to the calculation of carbon sources for built-up land, while this paper only calculated the carbon emissions generated by energy consumption.Therefore, the carbon sources and carbon emissions calculated in this paper were less than those in En Chen's research.Compared with the results of Junfeng Zhang et al. [69], the carbon emissions calculated in this paper were higher, and the reasons for the differences were as follows: his research overestimated the carbon sequestration function of cropland, and the overall carbon emissions from the cropland showed carbon sequestration, which led to lower-value research results.In addition, the carbon emissions from transportation introduced in his research are worth further study; however, it is still necessary to consider whether accurate estimates can be achieved to add to the final land-use carbon emission results.
The experimental results show that the Markov-PLUS model presented a significant improvement in the simulation and prediction effect of land use in the Wuhan Urban Agglomeration (kappa coefficient: 0.87; overall accuracy: 90%) compared to Haijun Wang et al. [70], who used the CA-Markov model to simulate built-up land use in the Wuhan urban area (overall accuracy: 80%).This solved the problem of traditional CA models lacking a relationship between impact factors and spatial changes.Compared to Zizheng Zhang et al.'s [71] use of the Markov-FLUS model (kappa coefficient: 0.85), there was a slight improvement, and this paper solved the problem of the lack of temporal attributes in the FLUS model.Compared to Guoping Huang et al.'s [72] use of the CLUE-S model in the Wuchang District, Wuhan City (kappa coefficient: 0.86), there was also a slight improvement, and this paper solved the problem of the CLUE-S model ignoring the possibility of non-dominant land-type transformations.The experimental results show a significant improvement compared to the PLUS model's research on the other regions, such as Jiening Wang et al.'s [73] simulation and prediction of land use in Shandong Province (kappa coefficient: 0.68), and Ziyao Wang et al.'s [74] simulation and prediction of land use in Beijing (kappa coefficient: 0.77).Compared with the results for the land-use simulation prediction of Yunnan Province (kappa coefficient: 0.89; overall accuracy: 0.93) by Rongyao Wang et al. [75], and of Changsha City (kappa coefficient: 0.91; overall accuracy: 0.95) by Kao Zhang et al. [40], there is still a gap in the research.The reason may be that the spatial resolution of land use in this paper is high; therefore, the prediction accuracy is slightly lower but the accuracy results meet the experimental requirements.In the future, methods can be found for optimization.

Innovations and Possible Improvement Directions
There were two main aspects to this paper and certain directions for future improvements.First of all, the carbon emission coefficient method was essentially an empirical model [11].This paper referred to the carbon emission coefficients in the relevant literature; however, those of built-up land in different regions varied greatly and the universality was poor.For example, Kangkang Yu et al. [43] calculated the carbon emission coefficient of built-up land in the Taihu Lake Basin as 65.30 t(C)/ hm 2 •a , and the research results of Na Lu [76] showed that the Chinese built-up land carbon emission coefficient was 40.73 t(C)/ hm 2 •a .Therefore, this study chose to indirectly calculate the carbon emissions of the Wuhan Urban Agglomeration based on the energy data.At the same time, a new problem arose, namely, it was difficult to obtain the energy data for previous years and below the municipal level.Therefore, based on the energy data and the area of built-up land, this study calculated the carbon emission coefficient of built-up land in line with the existing situation of the Wuhan Urban Agglomeration in order to obtain a more accurate result.However, the energy utilization efficiency of built-up land in different periods was still different [77]; therefore, the carbon emission coefficients for the same location during different periods will still present certain differences.Establishing an accurate carbon emission coefficient system to calculate the carbon emissions in different regions, time periods, and scales will be the focus of the future research.This paper explored the carbon emissions from land use in the Wuhan Urban Agglomeration through the changes in the trends of land use carbon emissions and structure between cities.Using the carbon emission coefficient method, the results obtained may be different to the actual value.However, this does not affect the judgment of the development trend obtained through long-term calculations and the structural judgment obtained through the calculations performed for different cities in the region.Through the research on their temporal and spatial differences, coupled with the implementation of relevant policies, it is beneficial to reveal the impact of policy implementation on land-use carbon emissions, and provide theoretical and technical support for subsequent research planning.
Secondly, this paper used the two aspects of land-use quantity constraints and landuse spatial transfer constraints to simulate the scenarios.Compared with other relevant research examples, such as Haishan He et al. [39], who only simulated scenarios based on the constraints of land-use area change, this paper not only realized the changes in land-use areas through quantitative constraints, but also performed more detailed scenario simulations, such as strictly restricting the encroachment on basic farmland by other land-use methods through spatial transfer constraints [78].The results of this study show that, although the low-carbon development scenario can considerably promote ecological protection, it inevitably hinders economic development.On the contrary, the economic development scenario ignores ecological protection while ensuring rapid economic development.Meanwhile, cropland was strictly protected and thus continuously expanded.These are relatively extreme scenarios, which obviously do not conform to the complex and diverse development scenarios in reality; however, they can show us the consequences of different decisions made from an extreme perspective.Therefore, how to simulate a comprehensive development scenario based on land-use conversion rules and the number of land-use conversions in the future, so as to find a better comprehensive and optimized development scenario, is a research point that needs to be considered.

Sustainability 2023 ,
15,  x FOR PEER REVIEW 4 of 23 population was 3248.88 million, accounting for 55.16% of the province's population; the gross domestic product (GDP) was CNY 26,361.01 billion, accounting for 60.38% of the province's GDP[37].With the advantages, such as its unique location, dense industry and personnel distribution, and national strategic support, the Wuhan Urban Agglomeration has developed rapidly and has become an important strategic fulcrum for the development of Hubei Province and the central region.According to the "14th Five-Year Plan for Natural Resources Protection and Development of Hubei Province" promulgated in 2021, reaching carbon peak and neutrality is an opportunity and a challenge for the province, which is taking the lead in realizing the green development in Central China.As a pioneer in the economic, social, and ecological development of Hubei Province, the Wuhan Urban Agglomeration views the realization of carbon peak and neutrality goals as an important task.

Figure 1 .
Figure 1.Research area of Wuhan Urban Agglomeration.

Figure 1 .
Figure 1.Research area of Wuhan Urban Agglomeration.
Sustainability 2023, 15, x FOR PEER REVIEW 9 of 23of ecological protection, which, in turn, led to the continuous growth of carbon emissions and increasingly serious ecological pollution.

Figure 2 .Figure 3
Figure 2. Land-use carbon emission results from 2000 to 2015.3.2.Trend Analysis of Land-Use Carbon Emissions in the Wuhan Urban Agglomeration from 2017 to 2022Figure3shows the results for the calculations of land-use carbon emissions in the Wuhan Urban Agglomeration from 2017 to 2022 using the carbon emission coefficient method.The average annual growth rates of carbon sources, sinks, and emissions from

Figure 4 .
Figure 4. Land-use types in the Wuhan Urban Agglomeration in 2020.Figure 4. Land-use types in the Wuhan Urban Agglomeration in 2020.

Figure 4 . 23 Figure 5 .
Figure 4. Land-use types in the Wuhan Urban Agglomeration in 2020.Figure 4. Land-use types in the Wuhan Urban Agglomeration in 2020.Sustainability 2023, 15, x FOR PEER REVIEW 11 of 23

Figure 5 .
Figure 5. Land-use-type area of each city in the Wuhan Urban Agglomeration in 2020.

Figure 6 .
Figure 6.Carbon emissions from land use in the Wuhan Urban Agglomeration in 2020.

Figure 6 .
Figure 6.Carbon emissions from land use in the Wuhan Urban Agglomeration in 2020.

Figure 7 .
Figure 7. Zoning of land-use carbon emissions in the Wuhan Urban Agglomeration in 2020.Figure 7. Zoning of land-use carbon emissions in the Wuhan Urban Agglomeration in 2020.

Figure 7 .
Figure 7. Zoning of land-use carbon emissions in the Wuhan Urban Agglomeration in 2020.Figure 7. Zoning of land-use carbon emissions in the Wuhan Urban Agglomeration in 2020.

Figure 8 .
Figure 8. Prediction of land-use spaces under multi-scenario simulations of the Wuhan Urban Agglomeration in 2035.

Figure 8 .
Figure 8. Prediction of land-use spaces under multi-scenario simulations of the Wuhan Urban Agglomeration in 2035.

Table 1 .
Factors for simulation prediction of land-use change.

Table 2 .
Data information and sources.

Table 3 .
Carbon emissions from land use in cities in the Wuhan Urban Agglomeration in 2020.

Table 4 .
Carbon emission zoning in the Wuhan Urban Agglomeration.

Table 4 .
Carbon emission zoning in the Wuhan Urban Agglomeration.

Table 5 .
Prediction of land-use quantity under a multi-scenario simulation of the Wuhan Urban Agglomeration in 2035.

Table 5 .
Prediction of land-use quantity under a multi-scenario simulation of the Wuhan Urban Agglomeration in 2035.

Table 6 .
Carbon emissions from different land-use types simulated under multi-scenario simulations of the Wuhan Urban Agglomeration in 2035.

Table 7 .
Carbon emissions from land use in different cities under multi-scenario simulations of the Wuhan Urban Agglomeration in 2035.